BASIS-SERIAL-MIB
The BASIS-SERIAL-MIB enables configuration and monitoring of serial port interfaces on Processor and Service Modules within Cisco MGX8850, MGX8250, and MGX8220 ATM edge switches. It provides management access to serial port operational states, error counters, and configuration parameters for legacy serial communication links on these specific hardware platforms.
Imported Objects
Objects
14 total| Object Name |
|---|
serialInterface OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.4.1 |
serialInterfaceTableThis table represents Physical serial interfaces in the module. SEQUENCE OF SerialInterfaceEntry .1.3.6.1.4.1.351.110.4.1.1 |
serialInterfaceEntryAn entry for each serial interface. Each entry contains information on port type, port speed. SerialInterfaceEntry .1.3.6.1.4.1.351.110.4.1.1.1 |
serialPortNumThis object identifies the serial port number. The value 1 is used for Console Port. The Console Port is also known as control port(CP). The value 2 is used for Maintenance Port and this can be used as SLIP (Serial Line Internet Protocol) interface. The Maintenance Port is also known as Modem Port(MP).ro Integer32 .1.3.6.1.4.1.351.110.4.1.1.1.1 |
serialPortTypeThis object identifies the type of port. main(1) : This is applicable for Maintenance Port debug(2) : This is applicable for Console Port.ro Enumeration .1.3.6.1.4.1.351.110.4.1.1.1.2 |
serialPortEnableThis object is used for enabling/disabling serial port.rw Enumeration .1.3.6.1.4.1.351.110.4.1.1.1.3 |
serialPortbpsThis object identifies the baud rate of the ports.rw Enumeration .1.3.6.1.4.1.351.110.4.1.1.1.4 |
serialPortNumOfValidEntriesThis object contains number of serial ports. This identifies the number of entries in serialInterfacetable.ro Integer32 .1.3.6.1.4.1.351.110.4.1.2 |
basisSerialMIBThe MIB module to configure serial ports in Processor Module and different Service Modules(cards) in MGX8850,MGX8250 and MGX8220 ATM Edge switches. MODULE-IDENTITY .1.3.6.1.4.1.351.150.69 |
basisSerialMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.69.2 |
basisSerialMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.69.2.1 |
basisSerialConfGroupThe collection of objects which are used to represent serial ports. Unknown .1.3.6.1.4.1.351.150.69.2.1.1 |
basisSerialMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.351.150.69.2.2 |
basisSerialComplianceThe compliance statement for objects related to Serial Ports. Unknown .1.3.6.1.4.1.351.150.69.2.2.1 |
More MIBs from Stratacom
Browse all StratacomMIBs →Standard SNMP MIB module defining data structures for CISCO-WAN-AXIPOP-MIB.
Standard SNMP MIB module defining data structures for STRATACOM-MIB.
The CISCO-WAN-SVC-MIB manages ATM service provisioning, configuration, and status monitoring on Cisco BPX-SES and MGX ATM switches, specifically tracking XPVC/XPVP segments, OAM cell handling, and ENNI auto-discovery via ILMI. It facilitates the administration of ATM traffic classes (CBR, VBR, UBR, ABR) and virtual circuit states (SVC, SPVC) across User-Network and Network-Network interfaces.
Standard SNMP MIB module defining data structures for CISCO-MGX82XX-SONET-MIB.
The CISCO-MGX82XX-DSX3-MIB enables configuration and monitoring of DS3/E3 interface parameters, including alarm states (AIS, LOF, RAI), performance statistics, and Bit Error Rate Testing (BERT) on Cisco MGX 8220/8230 T3/E3 service modules such as the CESM-T3E3 and FRSM-VHS. This module facilitates the management of physical layer convergence procedures (PLCP) and maintenance byte fields (Tx/Rx MA) defined by ITU-T G.832 for channelized T3 and E3 circuits.
The CISCO-WAN-PAR-MIB manages the Portable AutoRoute (PAR) controller on Cisco MGX and BPX switches to provision, monitor, and alarm connections while controlling LMI communication and clocking selection. It enables the configuration of routing capabilities, failure event conditioning, and the management of feeder-to-node signaling and switch synchronization.