BASIS-RAS-DISK-MIB
Standard SNMP MIB module defining data structures for BASIS-RAS-DISK-MIB.
Imported Objects
Objects
10 total| Object Name |
|---|
rasDsk OBJECT IDENTIFIER .1.3.6.1.4.1.351.110.6.2 |
IMPORTS Unknown .1.3.6.1.4.1.351.110.6.2 |
rasDskStatusIndicates whether the RAS Disk diagnostics has been
Enabled or not.rw Enumeration .1.3.6.1.4.1.351.110.6.2.1 |
dskHealthShows the Status of the Hard Disk, which depends on the
number of corrupted files and number of Bad sectors in
the ASC. The Status is PASS if there are no Corrupted
files in the Disk AND the number of Bad Sectors is within
the threshold value. If the Disk has one or more
Corrupted files OR if the Number of Bad Sectors exceeds
the threshold value, the Status is FAIL. If Diagnostics
is going on, the Status is TestInProgress. Status will be
UNKNOWN until the diagnostics starts for the first time.ro Enumeration .1.3.6.1.4.1.351.110.6.2.2 |
standbyDskHealthShows the Status of the Standby ASC Hard Disk, which
depends on the number of corrupted files and number of
Bad sectors in the Standby ASC. The Status is UNKNOWN, if
there is no Standby ASC in the shelf.ro Enumeration .1.3.6.1.4.1.351.110.6.2.3 |
wakeupIntervalIndicates the RAS Disk diagnostics task Wake up time
period, in HOURS. This Interval is configurable between
12 hours and 7 days. If RAS Disk diagnostics is Enabled,
the diagnostics starts whenever the wakeupInterval is
elapsed. If RAS Disk diagnostics is Enabled AND if the
CLI cnfrasdsk is executed, then the Disk diagnostics
starts immediately.rw INTEGER .1.3.6.1.4.1.351.110.6.2.4 |
lastTimeShows the Time when the RAS Disk diagnostics was
Last done. The format is DD MONTH HH:MM:SS.ro DisplayString .1.3.6.1.4.1.351.110.6.2.5 |
numBadSectorsIndicates the Number of Bad Sectors found in the Disk.ro INTEGER .1.3.6.1.4.1.351.110.6.2.6 |
crptdPRIfilesIndicates the Number of SM configuration files,
corrupted.ro INTEGER .1.3.6.1.4.1.351.110.6.2.7 |
crptdFWfilesIndicates the Number of FirmWare files, corrupted.ro INTEGER .1.3.6.1.4.1.351.110.6.2.8 |
More MIBs from Stratacom
Browse all StratacomMIBs →Standard SNMP MIB module defining data structures for CISCO-WAN-AXIPOP-MIB.
Standard SNMP MIB module defining data structures for STRATACOM-MIB.
The CISCO-WAN-SVC-MIB manages ATM service provisioning, configuration, and status monitoring on Cisco BPX-SES and MGX ATM switches, specifically tracking XPVC/XPVP segments, OAM cell handling, and ENNI auto-discovery via ILMI. It facilitates the administration of ATM traffic classes (CBR, VBR, UBR, ABR) and virtual circuit states (SVC, SPVC) across User-Network and Network-Network interfaces.
Standard SNMP MIB module defining data structures for CISCO-MGX82XX-SONET-MIB.
The CISCO-MGX82XX-DSX3-MIB enables configuration and monitoring of DS3/E3 interface parameters, including alarm states (AIS, LOF, RAI), performance statistics, and Bit Error Rate Testing (BERT) on Cisco MGX 8220/8230 T3/E3 service modules such as the CESM-T3E3 and FRSM-VHS. This module facilitates the management of physical layer convergence procedures (PLCP) and maintenance byte fields (Tx/Rx MA) defined by ITU-T G.832 for channelized T3 and E3 circuits.
The CISCO-WAN-PAR-MIB manages the Portable AutoRoute (PAR) controller on Cisco MGX and BPX switches to provision, monitor, and alarm connections while controlling LMI communication and clocking selection. It enables the configuration of routing capabilities, failure event conditioning, and the management of feeder-to-node signaling and switch synchronization.