AXprimoM210-MIB
AI MIB Summary
The AXprimoM210-MIB facilitates SNMP-based monitoring and management of AXprimoM210-08T and AXprimoM210-08P access switches, exposing standard interface statistics, port status states, and device health metrics.
The MIB module for AXprimoM210-08T and AXprimoM210-08P
Main OID:
axprimo-M210.1.3.6.1.4.1.21839.2.2.26
1111
Objects
Active
Status
10
Dependencies
Imported Objects
Objects
1111 total| Object Name |
|---|
alaxala OBJECT IDENTIFIER .1.3.6.1.4.1.21839 |
alaxalaMib OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2 |
axsEx OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2 |
axprimo-M210The MIB module for AXprimoM210-08T and AXprimoM210-08P MODULE-IDENTITY .1.3.6.1.4.1.21839.2.2.26 |
AXprimoM210MIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1 |
switchMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.1 |
switchNumberThe total number of switches present on this system.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.1.2 |
switchInfoTableTable of descriptive and status information about
the switch units in this system. SEQUENCE OF SwitchInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.1.3 |
switchInfoEntryTable providing descriptions and status information for
switch units. SwitchInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.1.3.1 |
swUnitIndexThis object identifies the switch within the system
for which this entry contains information. This
value can never be greater than switchNumber. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.1 |
swHardwareVerHardware version of the main board.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.2 |
swMicrocodeVerMicrocode version of the main board.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.3 |
swLoaderVerLoader version of the main board.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.4 |
swOpCodeVerOperation code version of the main board.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.6 |
swPortNumberThe number of ports on this switch.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.7 |
swPowerStatusIndicates the switch using internalPower(1),
redundantPower(2) or both(3)ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.8 |
swRoleInSystemIndicates the switch is master(1), backupMaster(2)
or slave(3) in this system.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.9 |
swSerialNumberSerial number of the switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.10 |
swServiceTagService tag serial-number of the switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.13 |
swModelNumberModel number of the switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.14 |
swEpldVerThe EPLD version of the switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.15 |
swLinuxVersionThe Linux Kernel version of the switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.3.1.17 |
switchOperStateGlobal operation state of the switch.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.1.4 |
switchProductId OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.1.5 |
swProdNameThe product name of this switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.5.1 |
swProdManufacturerThe product manufacturer of this switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.5.2 |
swProdDescriptionThe product description of this switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.5.3 |
swProdVersionThe runtime code version of this switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.5.4 |
swProdUrlThe URL of this switch, which we can connect through
a web browser.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.5.5 |
swIdentifierA unique identifier of which switch in the chassis is currently
being looked at.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.1.5.6 |
swChassisServiceTagThe service tag of the chassis this switch resides in.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.1.5.7 |
switchIndivPowerTableTable about the status of individual powers. SEQUENCE OF SwitchIndivPowerEntry .1.3.6.1.4.1.21839.2.2.26.1.1.6 |
switchIndivPowerEntryTable about the status of individual power. SwitchIndivPowerEntry .1.3.6.1.4.1.21839.2.2.26.1.1.6.1 |
swIndivPowerUnitIndexThis is defined as swUnitIndex.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.1.6.1.1 |
swIndivPowerIndex1 means internal power, 2 means external power.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.1.6.1.2 |
swIndivPowerStatusnotPresent(1) means not present, green(2) means
up, red(3) means down.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.1.6.1.3 |
switchJumboFrameStatusenable(1) means the Jumbo Frame has enabled, disabled(2)
means the Jumbo Frame has disabled.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.1.7 |
amtrMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.1.8 |
amtrMacAddrAgingStatusIf this is enabled(1), the MAC address table will age out according to
its timer. If this is disabled(2), the MAC address table will not
age out.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.1.8.3 |
amtrMacAddrDynamicCountThe number of dot1dTpFdbTable entries in the BRIDGE-MIB.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.1.8.4 |
amtrMacAddrStaticCountThe number of dot1dStaticTable entries in the BRIDGE-MIB.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.1.8.5 |
amtrMacAddrTotalCountThe sum of dot1dTpFdbTable and dot1dStaticTable entries.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.1.8.6 |
portMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.2 |
portTableTable of descriptive and status information describing
the configuration of each switch port. This table also
contains information about each trunk. SEQUENCE OF PortEntry .1.3.6.1.4.1.21839.2.2.26.1.2.1 |
portEntryAn entry in the table, describing the configuration of
one switch port or trunk. PortEntry .1.3.6.1.4.1.21839.2.2.26.1.2.1.1 |
portIndexThe port and the trunk (including trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by the same
value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.1 |
portNameThe name of the port or trunk. This is the same as ifAlias
in the IF-MIB (RFC2863 or later).rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.2 |
portTypeIndicates the port type of the configuration of the switch.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.3 |
portSpeedDpxCfgConfigures the speed and duplex mode for a port or trunk,
according to:
halfDuplex10(2) - 10Mbps and half duplex mode
fullDuplex10(3) - 10Mbps and full duplex mode
halfDuplex100(4) - 100Mbps and half duplex mode
fullDuplex100(5) - 100Mbps and full duplex mode
halfDuplex1000(6) - 1000Mbps and half duplex mode
fullDuplex1000(7) - 1000Mbps and full duplex mode
halfDuplex10g(8) - 10g and half duplex mode
fullDuplex10g(9) - 10g and full duplex mode
hundredBaseTX port can be set as:
halfDuplex10(2)
fullDuplex10(3)
halfDuplex100(4)
fullDuplex100(5)
hundredBaseFX port can be set as:
fullDuplex100(5)
thousandBaseSX port can be set as:
fullDuplex1000(7)
thousandBaseLX port can be set as:
fullDuplex1000(7)
thousandBaseT port can be set as:
halfDuplex10(2)
fullDuplex10(3)
halfDuplex100(4)
fullDuplex100(5)
thousandBaseGBIC port can be set as:
fullDuplex1000(7)
thousandBaseSfp port can be set as:
fullDuplex1000(7)
hundredBaseFxScSingleMode port can be set as:
fullDuplex100(5)
hundredBaseFxScMultiMode port can be set as:
fullDuplex100(5)
thousandBaseCX port can be set as:
fullDuplex1000(7)
tenG port can be set as:
halfDuplex10g(8)
fullDuplex10g(9)
The actual operating speed and duplex of the port
is given by portSpeedDpxStatus.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.4 |
portFlowCtrlCfg(1) Flow control mechanism is enabled with tx and rx pause
mechansim.
If the port type is hundredBaseTX or thousandBaseSX:
When the port is operating in halfDuplex mode, the
port uses backPressure flow control mechanism. When
the port is operating in fullDuplex mode, the port
uses IEEE 802.3x flow control mechanism.
If the port type is hundredBaseFX:
When the port is operating in halfDuplex mode, the
port uses backPressure flow control mechanism. When
the port is operating in fullDuplex mode, Flow
control mechanism will not function.
(2) Flow control mechanism is disabled.
(5) Flow control mechanism is enabled with tx pause
mechanism only.
(6) Flow control mechansim is enabled with rx pause
mechansim only.
Fast ethernet ports can be set as:
enabled(1),
disabled(2).
Gigabit ethernet ports can be set as:
enabled(1),
disabled(2),
tx(5),
rx(6).
The actual flow control mechanism is used given by
portFlowCtrlStatus.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.5 |
portCapabilitiesPort or trunk capabilities.rw Bits .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.6 |
portAutonegotiationWhether auto-negotiation is enabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.7 |
portSpeedDpxStatusThe operating speed and duplex mode of the
switched port or trunk. If the entry represents a trunk,
the speed is that of its individual members unless
the member ports have been inconsistently configured
in which case the value is error(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.8 |
portFlowCtrlStatus(2) BackPressure flow control mechanism is used.
(3) IEEE 802.3 flow control mechanism is used.
(4) Flow control mechanism is disabled.
If the entry represents a trunk and the member ports
have been inconsistently configured then this value
is error(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.9 |
portTrunkIndexThe trunk to which this port belongs. A value of 0
means that this port does not belong to any trunk.
A value greater than zero means that this port
belongs to a trunk in the trunkIndex, defined by the
corresponding trunkPorts.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.10 |
portComboForcedModeThis determines the running mode of a combo port.
For a non-combo port, this variable has a value of none(1),
and setting this variable to none(1) has no effect.
For a combo port, this has its own valid values not
equal to none(1), and setting this variable to none(1) is
not allowed. sfpForced(4) is set if user want to force
this port running in fiber mode.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.12 |
portMasterSlaveModeCfgConfigures the PHY mode when auto negotiation is disabled and
speed-duplex is 1000full for giga copper port.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.15 |
portMacAddrLearningStatusSet this variable to enabled(1) to start to learn MAC
addresses. Set this variable to disabled(2) to stop to
learn MAC addresses.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.17 |
portMacAddrLearningCountThe current number of learned MAC addresses.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.18 |
portUpTimeThe port up time (in hundredths of a second).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.19 |
portShutdownReasonThe reason of port shutdown. The value is 0 if no
shutdown action is applied to this port.ro Bits .1.3.6.1.4.1.21839.2.2.26.1.2.1.1.20 |
cableDiagMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.2.3 |
cableDiagCtlActionTo execute cable diagnostics on a port, assign
cableDiagCtlAction to the value of ifIndex defined
by the ifIndex in the IF-MIB. When read, this object
always returns 0.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.3.1 |
cableDiagResultTableTable for cable diagnostics result. SEQUENCE OF CableDiagResultEntry .1.3.6.1.4.1.21839.2.2.26.1.2.3.2 |
cableDiagResultEntryEntry for cable diagnostics result. CableDiagResultEntry .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1 |
cableDiagResultIfIndexThis is defined as the ifIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.1 |
cableDiagResultStatusPairAThe result of cable diagnostics. If there is no fault
on the cable, the value is ok(2). Value notTestedYet(1)
means the pair is not tested yet. Value ok(2) means the
pair works well. Value open(3) means there is a lack of
continuity between pins at each end of the pair. Value
short(4) means conductors are short-circuited together on
the pair. Value openShort(5) means the pair has open
and short issues. Value crosstalk(6) means the pair is
incorrectly connected at one end. Value unknown(7) means
pair has an error matching none of the above. Value
impedanceMismatch(8) means different quality cables
connected together. Value failed(9) means test failed.
Value notSupported(10) means cable diagnostics is not
supported. Value noCable(11) means there is no connected
cable.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.2 |
cableDiagResultStatusPairBThe result of cable diagnostics. If there is no fault
on the cable, the value is ok(2). Value notTestedYet(1)
means the pair is not tested yet. Value ok(2) means the
pair works well. Value open(3) means there is a lack of
continuity between pins at each end of the pair. Value
short(4) means conductors are short-circuited together on
the pair. Value openShort(5) means the pair has open
and short issues. Value crosstalk(6) means the pair is
incorrectly connected at one end. Value unknown(7) means
pair has an error matching none of the above. Value
impedanceMismatch(8) means different quality cables
connected together. Value failed(9) means test failed.
Value notSupported(10) means cable diagnostics is not
supported. Value noCable(11) means there is no connected
cable.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.3 |
cableDiagResultStatusPairCThe result of cable diagnostics. If there is no fault
on the cable, the value is ok(2). Value notTestedYet(1)
means the pair is not tested yet. Value ok(2) means the
pair works well. Value open(3) means there is a lack of
continuity between pins at each end of the pair. Value
short(4) means conductors are short-circuited together on
the pair. Value openShort(5) means the pair has open
and short issues. Value crosstalk(6) means the pair is
incorrectly connected at one end. Value unknown(7) means
pair has an error matching none of the above. Value
impedanceMismatch(8) means different quality cables
connected together. Value failed(9) means test failed.
Value notSupported(10) means cable diagnostics is not
supported. Value noCable(11) means there is no connected
cable.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.4 |
cableDiagResultStatusPairDThe result of cable diagnostics. If there is no fault
on the cable, the value is ok(2). Value notTestedYet(1)
means the pair is not tested yet. Value ok(2) means the
pair works well. Value open(3) means there is a lack of
continuity between pins at each end of the pair. Value
short(4) means conductors are short-circuited together on
the pair. Value openShort(5) means the pair has open
and short issues. Value crosstalk(6) means the pair is
incorrectly connected at one end. Value unknown(7) means
pair has an error matching none of the above. Value
impedanceMismatch(8) means different quality cables
connected together. Value failed(9) means test failed.
Value notSupported(10) means cable diagnostics is not
supported. Value noCable(11) means there is no connected
cable.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.5 |
cableDiagResultDistancePairADisplays the fault distance of pair A of the cable
in meters.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.6 |
cableDiagResultDistancePairBDisplays the fault distance of pair B of the cable
in meters.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.7 |
cableDiagResultDistancePairCDisplays the fault distance of pair C of the cable
in meters.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.8 |
cableDiagResultDistancePairDDisplays the fault distance of pair D of the cable
in meters.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.9 |
cableDiagResultTimeDisplays the last time of cable diagnostics.
For example, 'Jan 1 02:03:04 2002'.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.3.2.1.11 |
portUtilTableDispalys port utilization during recent 300 seconds. SEQUENCE OF PortUtilEntry .1.3.6.1.4.1.21839.2.2.26.1.2.6 |
portUtilEntryDispalys port utilization during recent 300 seconds. PortUtilEntry .1.3.6.1.4.1.21839.2.2.26.1.2.6.1 |
portUtilIfIndexThe port and trunk interface of the portUtilTable.
The interface identified by a particular value of this
index is the same interface identified by the same value
of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.6.1.1 |
portInOctetRateThe input octet rate (kbits/sec) of the port.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.6.1.2 |
portInPacketRateThe input packet rate (pkts/sec) of the port.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.6.1.3 |
portInUtilThe input utilization of the port, in one per
hundred.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.6.1.4 |
portOutOctetRateThe output octet rate (kbits/sec) of the port.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.6.1.5 |
portOutPacketRateThe output packet rate (pkts/sec) of the port.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.6.1.6 |
portOutUtilThe output utilization of the port, in one per
hundred.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.6.1.7 |
portHist OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.2.8 |
portHistControlTableA list of history control entries. SEQUENCE OF PortHistControlEntry .1.3.6.1.4.1.21839.2.2.26.1.2.8.1 |
portHistControlEntryA list of parameters that set up a periodic sampling of
statistics. PortHistControlEntry .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1 |
portHistControlIndexAn index that uniquely identifies an entry in the
portHistControl table.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1.1 |
portHistControlNameA textual name of the entity. It is mandatory that
this only contain printable ASCII characters.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1.2 |
portHistControlDataSourceThis object identifies the source of the data for
which historical data was collected and
placed in a media-specific table on behalf of this
portHistControlEntry. This source can be any
interface on this device.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1.3 |
portHistControlIntervalThe interval in seconds over which the data is
sampled for each bucket in the part of the
media-specific table associated with this
portHistControlEntry. This interval can
be set to any number of seconds between 1 and
86400 (1 day).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1.4 |
portHistControlBucketsRequestedThe requested number of discrete time intervals
over which data is to be saved in the part of the
media-specific table associated with this
portHistControlEntry.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1.5 |
portHistControlBucketsGrantedThe number of discrete sampling intervals
over which data shall be saved in the part of
the media-specific table associated with this
portHistControlEntry.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1.6 |
portHistControlStatusThe status of this portHistControl entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.2.8.1.1.7 |
portHistCurrentTableA list of Ethernet history entries. SEQUENCE OF PortHistCurrentEntry .1.3.6.1.4.1.21839.2.2.26.1.2.8.2 |
portHistCurrentEntryAn historical sample of Ethernet statistics on a particular
Ethernet interface. This sample is associated with the
portHistControlEntry which set up the parameters for
a regular collection of these samples. PortHistCurrentEntry .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1 |
portHistCurrentIndexThe history of which this entry is a part. The
history identified by a particular value of this
index is the same history as identified
by the same value of portHistControlIndex.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.1 |
portHistCurrentSampleIndexAn index that uniquely identifies the particular
sample this entry represents among all samples
associated with the same portHistControlEntry.
This index starts at 1 and increases by one
as each new sample is taken.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.2 |
portHistCurrentIntervalStartThe value of sysUpTime at the start of the interval
over which this sample was measured.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.3 |
portHistCurrentInOctetsThe total number of octets received on the interface,
including framing characters.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.4 |
portHistCurrentInUcastPktsThe number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were not addressed to a multicast
or broadcast address at this sub-layer.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.5 |
portHistCurrentInMulticastPktsThe number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were addressed to a multicast
address at this sub-layer. For a MAC layer protocol, this
includes both Group and Functional addresses.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.6 |
portHistCurrentInBroadcastPktsThe number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were addressed to a broadcast
address at this sub-layer.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.7 |
portHistCurrentInDiscardsThe number of inbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being deliverable to a higher-layer protocol. One
possible reason for discarding such a packet could be to
free up buffer space.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.8 |
portHistCurrentInErrorsFor packet-oriented interfaces, the number of inbound
packets that contained errors preventing them from
being deliverable to a higher-layer protocol. For
character-oriented or fixed-length interfaces, the
number of inbound transmission units that contained
errors preventing them from being deliverable to a
higher-layer protocol.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.9 |
portHistCurrentInUnknownProtosFor packet-oriented interfaces, the number of packets
received via the interface which were discarded because of
an unknown or unsupported protocol. For character-oriented
or fixed-length interfaces that support protocol
multiplexing the number of transmission units received via
the interface which were discarded because of an unknown or
unsupported protocol. For any interface that does not
support protocol multiplexing, this counter will always be
0.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.10 |
portHistCurrentOutOctetsThe total number of octets transmitted out of the
interface, including framing characters.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.11 |
portHistCurrentOutUcastPktsThe total number of packets that higher-level protocols
requested be transmitted, and which were not addressed to a
multicast or broadcast address at this sub-layer, including
those that were discarded or not sent.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.12 |
portHistCurrentOutMulticastPktsThe total number of packets that higher-level protocols
requested be transmitted, and which were addressed to a
multicast address at this sub-layer, including those that
were discarded or not sent. For a MAC layer protocol, this
includes both Group and Functional addresses.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.13 |
portHistCurrentOutBroadcastPktsThe total number of packets that higher-level protocols
requested be transmitted, and which were addressed to a
broadcast address at this sub-layer, including those that
were discarded or not sent.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.14 |
portHistCurrentOutDiscardsThe number of outbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being transmitted. One possible reason for discarding
such a packet could be to free up buffer space.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.15 |
portHistCurrentOutErrorsFor packet-oriented interfaces, the number of outbound
packets that could not be transmitted because of errors.
For character-oriented or fixed-length interfaces, the
number of outbound transmission units that could not be
transmitted because of errors.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.16 |
portHistCurrentInUtilizationThe best estimate of the mean physical layer
network utilization on this interface during this
sampling interval, in hundredths of a percent.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.17 |
portHistCurrentOutUtilizationThe best estimate of the mean physical layer
network utilization on this interface during this
sampling interval, in hundredths of a percent.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.2.1.18 |
portHistPreviousTableA list of Ethernet history entries. SEQUENCE OF PortHistPreviousEntry .1.3.6.1.4.1.21839.2.2.26.1.2.8.3 |
portHistPreviousEntryAn historical sample of Ethernet statistics on a particular
Ethernet interface. This sample is associated with the
portHistControlEntry which set up the parameters for
a regular collection of these samples. PortHistPreviousEntry .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1 |
portHistPreviousIndexThe history of which this entry is a part. The
history identified by a particular value of this
index is the same history as identified
by the same value of portHistControlIndex.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.1 |
portHistPreviousSampleIndexAn index that uniquely identifies the particular
sample this entry represents among all samples
associated with the same portHistControlEntry.
This index starts at 1 and increases by one
as each new sample is taken.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.2 |
portHistPreviousIntervalStartThe value of sysUpTime at the start of the interval
over which this sample was measured.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.3 |
portHistPreviousInOctetsThe total number of octets received on the interface,
including framing characters.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.4 |
portHistPreviousInUcastPktsThe number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were not addressed to a multicast
or broadcast address at this sub-layer.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.5 |
portHistPreviousInMulticastPktsThe number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were addressed to a multicast
address at this sub-layer. For a MAC layer protocol, this
includes both Group and Functional addresses.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.6 |
portHistPreviousInBroadcastPktsThe number of packets, delivered by this sub-layer to a
higher (sub-)layer, which were addressed to a broadcast
address at this sub-layer.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.7 |
portHistPreviousInDiscardsThe number of inbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being deliverable to a higher-layer protocol. One
possible reason for discarding such a packet could be to
free up buffer space.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.8 |
portHistPreviousInErrorsFor packet-oriented interfaces, the number of inbound
packets that contained errors preventing them from
being deliverable to a higher-layer protocol. For
character-oriented or fixed-length interfaces, the
number of inbound transmission units that contained
errors preventing them from being deliverable to a
higher-layer protocol.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.9 |
portHistPreviousInUnknownProtosFor packet-oriented interfaces, the number of packets
received via the interface which were discarded because of
an unknown or unsupported protocol. For character-oriented
or fixed-length interfaces that support protocol
multiplexing the number of transmission units received via
the interface which were discarded because of an unknown or
unsupported protocol. For any interface that does not
support protocol multiplexing, this counter will always be
0.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.10 |
portHistPreviousOutOctetsThe total number of octets transmitted out of the
interface, including framing characters.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.11 |
portHistPreviousOutUcastPktsThe total number of packets that higher-level protocols
requested be transmitted, and which were not addressed to a
multicast or broadcast address at this sub-layer, including
those that were discarded or not sent.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.12 |
portHistPreviousOutMulticastPktsThe total number of packets that higher-level protocols
requested be transmitted, and which were addressed to a
multicast address at this sub-layer, including those that
were discarded or not sent. For a MAC layer protocol, this
includes both Group and Functional addresses.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.13 |
portHistPreviousOutBroadcastPktsThe total number of packets that higher-level protocols
requested be transmitted, and which were addressed to a
broadcast address at this sub-layer, including those that
were discarded or not sent.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.14 |
portHistPreviousOutDiscardsThe number of outbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being transmitted. One possible reason for discarding
such a packet could be to free up buffer space.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.15 |
portHistPreviousOutErrorsFor packet-oriented interfaces, the number of outbound
packets that could not be transmitted because of errors.
For character-oriented or fixed-length interfaces, the
number of outbound transmission units that could not be
transmitted because of errors.ro Counter64 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.16 |
portHistPreviousInUtilizationThe best estimate of the mean physical layer
network utilization on this interface during this
sampling interval, in hundredths of a percent.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.17 |
portHistPreviousOutUtilizationThe best estimate of the mean physical layer
network utilization on this interface during this
sampling interval, in hundredths of a percent.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.8.3.1.18 |
portMediaInfoTableThis table lists the information of the media device
(SFP/XFP/Copper) installed in the physical port.
Only the ifIndices of Ethernet ports those are associated
with the operational cards will be included in this table. SEQUENCE OF PortMediaInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.2.10 |
portMediaInfoEntryAn entry in the Interface Media Information table.
The ifIndices of ethernet interfaces will be used
to index this table. PortMediaInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.2.10.1 |
portMediaInfoIfIndexifindex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.1 |
portMediaInfoConnectorTypeThe connector type.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.2 |
portMediaInfoFiberTypeThe fiber type.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.3 |
portMediaInfoEthComplianceCodesThe ethernet compliance codes.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.4 |
portMediaInfoBaudRateThe baud rate.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.5 |
portMediaInfoVendorOUIThe OUI of the vendor.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.6 |
portMediaInfoVendorNameThe media vendor name, full name of the corporation.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.7 |
portMediaInfoPartNumberThe media vendor part number.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.8 |
portMediaInfoRevisionThe media vendor product version number.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.9 |
portMediaInfoSerialNumberThe vendor serial number of the media device.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.10 |
portMediaInfoDateCodeThe date code of the media device.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.10.1.11 |
portOpticalMonitoringInfoTableThis table lists the instrumented parameters of all
optical interfaces. SEQUENCE OF PortOpticalMonitoringInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.2.11 |
portOpticalMonitoringInfoEntryOnly the ifIndices of optical interfaces
whose parameters need to be monitored will
be used to index this table. PortOpticalMonitoringInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.2.11.1 |
portOpticalMonitoringInfoIfIndexifindex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.11.1.1 |
portOpticalMonitoringInfoTemperatureThis object holds the value of the transmitter laser
diode temperature for the interface. This object
indicates the health of the transmitter.
The format is xxx.yyyy C(elcius). If the device supports
ALARM WARNING TRAP, then followed by whether the measured
value is normal, high/low alarm or high/low warning.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.11.1.2 |
portOpticalMonitoringInfoVccThis object holds the value of the Vcc. It is measured
in V. If the device supports ALARM WARNING TRAP, then
followed by whether the measured value is normal,
high/low alarm or high/low warning.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.11.1.3 |
portOpticalMonitoringInfoTxBiasCurrentTx Bias Current. It is measured in mA. If the device
supports ALARM WARNING TRAP, then followed by whether
the measured value is normal, high/low alarm or
high/low warning.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.11.1.4 |
portOpticalMonitoringInfoTxPowerThis object holds the value of the transmitter optical
signal power for the interface, measured in dBm. If the
device supports ALARM WARNING TRAP, then followed by
whether the measured value is normal, high/low alarm
or high/low warning.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.11.1.5 |
portOpticalMonitoringInfoRxPowerThis object holds the value of the receiver optical
signal power for the interface, measured in dBm. If
the device support ALARM WARNING TRAP, then followed
by whether the measured value is normal, high/low alarm
or high/low warning.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.2.11.1.6 |
portTransceiverThresholdInfoTableThis table lists the threshold of transceivers. SEQUENCE OF PortTransceiverThresholdInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.2.12 |
portTransceiverThresholdInfoEntryIdentify the index of the transceiver PortTransceiverThresholdInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.2.12.1 |
portTransceiverThresholdInfoIfIndexifindex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.1 |
portTransceiverThresholdInfoTemperatureLowAlarmThis object holds the low alarm threshold of
the transmitter laser diode temperature for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.2 |
portTransceiverThresholdInfoTemperatureLowWarnThis object holds the low warning threshold of
the transmitter laser diode temperature for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.3 |
portTransceiverThresholdInfoTemperatureHighWarnThis object holds the high warning threshold of
the transmitter laser diode temperature for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.4 |
portTransceiverThresholdInfoTemperatureHighAlarmThis object holds the high alarm threshold of
the transmitter laser diode temperature for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.5 |
portTransceiverThresholdInfoVccLowAlarmThis object holds the low alarm threshold
of the Vcc.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.6 |
portTransceiverThresholdInfoVccLowWarnThis object holds the low warning threshold
of the Vcc.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.7 |
portTransceiverThresholdInfoVccHighWarnThis object holds the high warning threshold
of the Vcc.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.8 |
portTransceiverThresholdInfoVccHighAlarmThis object holds the high alarm threshold
of the Vcc.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.9 |
portTransceiverThresholdInfoTxBiasCurrentLowAlarmlow alarm threshold of Tx Bias Current.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.10 |
portTransceiverThresholdInfoTxBiasCurrentLowWarnlow warning threshold of Tx Bias Current.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.11 |
portTransceiverThresholdInfoTxBiasCurrentHighWarnhigh warning threshold of Tx Bias Current.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.12 |
portTransceiverThresholdInfoTxBiasCurrentHighAlarmhigh alarm threshold of Tx Bias Current.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.13 |
portTransceiverThresholdInfoTxPowerLowAlarmThis object holds the low alarm threshold
of the transmitter optical signal power
for theinterface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.14 |
portTransceiverThresholdInfoTxPowerLowWarnThis object holds the low warning threshold
of the transmitter optical signal power
for the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.15 |
portTransceiverThresholdInfoTxPowerHighWarnThis object holds the high warning threshold
of the transmitter optical signal power
for the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.16 |
portTransceiverThresholdInfoTxPowerHighAlarmThis object holds the high alarm threshold
of the transmitter optical signal power for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.17 |
portTransceiverThresholdInfoRxPowerLowAlarmThis object holds the low alarm threshold
of the receiver optical signal power for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.18 |
portTransceiverThresholdInfoRxPowerLowWarnThis object holds the low warning threshold
of the receiver optical signal power for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.19 |
portTransceiverThresholdInfoRxPowerHighWarnThis object holds the high warning threshold
of the receiver optical signal power for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.20 |
portTransceiverThresholdInfoRxPowerHighAlarmThis object holds the high alarm threshold
of the receiver optical signal power for
the interface.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.21 |
portTransceiverThresholdAutoModeIndicate the transceiver threshold is retrieved from
EEPROM or configured by user.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.2.12.1.22 |
powerSavingTableTable for power saving configuration. SEQUENCE OF PowerSavingEntry .1.3.6.1.4.1.21839.2.2.26.1.2.14 |
powerSavingEntryAn entry describing the configuration and status for
power saving. PowerSavingEntry .1.3.6.1.4.1.21839.2.2.26.1.2.14.1 |
powerSavingIfIndexThe port interface of the powerSavingTable. The interface
identified by a particular value of this index is the same
interface as identified by the same value of ifIndex in the
IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.14.1.1 |
powerSavingStatusPower saving enabled status.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.2.14.1.2 |
trunkMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.3 |
trunkMaxIdThe maximum number for a trunk identifier.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.3.1 |
trunkValidNumberThe number of valid trunks.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.3.2 |
trunkTableTable describing the configuration and status of each
trunk. SEQUENCE OF TrunkEntry .1.3.6.1.4.1.21839.2.2.26.1.3.3 |
trunkEntryAn entry describing the configuration and status of a
particular trunk. TrunkEntry .1.3.6.1.4.1.21839.2.2.26.1.3.3.1 |
trunkIndexIdentifies the trunk within the switch that is
described by the table entry. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.3.3.1.1 |
trunkPortsThe complete set of ports currently associated with
this trunk.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.3.3.1.2 |
trunkCreationA value of static(1) means a statically configured trunk.
A value of lacp(2) means an LACP-configured trunk.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.3.3.1.3 |
trunkStatusWriting this to valid(1) creates an entry.
Writing this to invalid(2) destroys an entry.
A trunk created by LACP cannot be manually destroyed
or (re)configured.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.3.3.1.4 |
trunkBalanceModeThis defines the load balancing mode of trunks
in the system. It may be based on source and/or
destination MAC address or IP address.
macSrc(1) means source MAC address.
macDst(2) means destination MAC address.
macSrcDst(3) means source and destination MAC address.
ipSrc(4) means source IP address.
ipDst(5) means destination IP address.
ipSrcDst(6) means source and destination IP address.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.3.4 |
lacpMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.4 |
lacpPortTableTable for LACP port configuration. SEQUENCE OF LacpPortEntry .1.3.6.1.4.1.21839.2.2.26.1.4.1 |
lacpPortEntryEntry for LACP port configuration. While an entry may
exist for a particular port, the port may not support
LACP and an attempt to enable LACP may result in
failure. LacpPortEntry .1.3.6.1.4.1.21839.2.2.26.1.4.1.1 |
lacpPortIndexThe port interface of the lacpPortTable. The interface
identified by a particular value of this index is the
same interface as identified by the same value of
ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.4.1.1.1 |
lacpPortStatusWhether 802.3ad LACP is enabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.4.1.1.2 |
staMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.5 |
staSystemStatusGlobal spanning tree status.
(1) Spanning tree protocol is enabled.
(2) Spanning tree protocol is disabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.1 |
staPortTableThe table manages port settings for Spanning Tree
Protocol 802.1d, 802.1w or 802.1s depending on the
value specified by staProtocolType. SEQUENCE OF StaPortEntry .1.3.6.1.4.1.21839.2.2.26.1.5.2 |
staPortEntryThe conceptual entry of staPortTable. StaPortEntry .1.3.6.1.4.1.21839.2.2.26.1.5.2.1 |
staPortProtocolMigrationWhen operating in RSTP (version 2) mode, writing true(1)
to this object forces this port to transmit RSTP BPDUs.
Any other operation on this object has no effect and
it always returns false(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.3 |
staPortOperEdgePortThe operational value of the edge port parameter. The object is
initialized to the value of staPortAdminEdgePort and is set false
when a BPDU is received.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.5 |
staPortAdminPointToPointThe administrative point-to-point status of the LAN segment
attached to this port. A value of forceTrue(0) indicates that
this port should always be treated as if it is connected to
a point-to-point link. A value of forceFalse(1) indicates
that this port should be treated as having a shared media
connection. A value of auto(2) indicates that this port is
considered to have a point-to-point link if it is an Aggregator
and all of its members are aggregatable, or if the MAC entity
is configured for full duplex operation, either through
auto-negotiation or by management means.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.6 |
staPortOperPointToPointThe operational point-to-point status of the LAN segment
attached to this port. This indicates whether a port is
considered to have a point-to-point connection or not.
The value is determined by management or by auto-detection,
as described in the staPortAdminPointToPoint object.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.7 |
staPortSystemStatusPer-port spanning tree status.
(1) Spanning tree protocol is enabled.
(2) Spanning tree protocol is disabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.9 |
staPortLongAdminPathCostThe admin value of the RSTP path cost or MST external pathcost.
The contribution of this port to the path cost (in 32
bits value) of paths towards the spanning tree root which
include this port.
This object is used to configure the spanning tree port
path cost in the 32-bit value range when the
staPathCostMethod is long(2).
If the staPathCostMethod is short(1), this mib object is not
instantiated.
Setting this to 0 means that the path cost is automatically
determined. In this case, read staPortLongOperPathCost to get
the oper value.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.10 |
staPortLongOperPathCostThe oper value of the RSTP path cost or MST external pathcost.
The contribution of this port to the path cost (in 32
bits value) of paths towards the spanning tree root which
include this port.
This object is used to configure the spanning tree port
path cost in the 32-bit value range when the
staPathCostMethod is long(2).
If the staPathCostMethod is short(1), this mib object is not
instantiated.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.11 |
staPortBpduFloodingThis parameter is used to configure the capability of BPDUs
flooding.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.12 |
staPortBpduGuardA value of enabled(1) indicates that BPDU port guard feature
is enabled for each port. A value of disabled(2) indicates
that the feature is disabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.15 |
staPortAdminEdgePortWithAutoThe administrative value of the edge port parameter.
A value of enable(1) indicates that this port should be
assumed as an edge-port, a value of disable(2) indicates
that this port should be assumed as a non-edge-port and
a value of auot (3) indicates this port in RSPT or MSTP mode
should be assumed as an edge-port after migration or max age expire
without receiving any BPDU and sending BPDU with proposal flag on.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.16 |
staPortBpduFilterThe administrative value of the BPDU filter parameter.
A value of enabled(1) indicates that this port will avoid
transmitting BPDUs on edge-port and the value of disabled(2)
indicates that this port will not avoid transmitting BPDUs
on edge-port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.17 |
staPortRootGuardStatusSpecifies the desired status of the root guard. This variable
configures the root guard feature to enforce the root bridge
placement in the network.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.18 |
staPortBpduGuardAutoRecoveryA value of enabled(1) indicates that BPDU port guard auto
recovery mechanism is enabled for this port. A value of
disabled(2) indicates that the mechanism is disabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.19 |
staPortBpduGuardAutoRecoveryIntervalThe interval in seconds used by BPDU guard auto recovery
mechanism.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.20 |
staPortTcPropStopStop topology change progate on this ifindex.
Don't enable on potentially ring port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.5.2.1.21 |
staProtocolTypeThe version of Spanning Tree Protocol the bridge is currently
running. The value 'stp(1)' indicates the Spanning Tree
Protocol is as specified in IEEE 802.1D,'rstp(2)' indicates that
the Rapid Spanning Tree Protocol is as specified in IEEE
802.1w, and the value 'mstp(3)' indicates that the Multiple Spanning
Tree Protocol is as specified in IEEE 802.1s. New values may
be defined in the future as new or updated versions of the
protocol become available.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.3 |
staTxHoldCountThe value used by the Port Transmit state machine to limit
the maximum transmission rate.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.4 |
staPathCostMethodIndicates the type of spanning tree path cost mode configured
on the switch. This mode applies to all instances of the
spanning tree protocol running on the switch.
When the value of this MIB object is changed, the path cost of
all ports will be reassigned to the default path cost values
based on the new spanning tree path cost mode and the
ports' speed.
When the value of this MIB object is set to long(2), the
staPortLongPathCost MIB object must be used to retrieve/configure
the spanning tree port path cost as a 32-bit value.
The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected.
While retrieving the value of dot1dStpPortPathCost, the maximum
value of 65535 will be returned if the value of staPortLongPathCost
for the same instance exceeds 65535.
When the value of this MIB object is set to short(1), the
dot1dStpPortPathCost in BRIDGE-MIB must be used.rw StaPathCostMode .1.3.6.1.4.1.21839.2.2.26.1.5.5 |
xstMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.5.6 |
mstNameThe name of the Multiple Spanning Tree region.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.5.6.1 |
mstRevisionThe Revision number of the Multiple Spanning Tree region.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.2 |
mstMaxHopsThe max hop number counts of the Multiple Spanning Tree region.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.3 |
xstInstanceCfgTableThis table is used to configure the property of a specific
instance in Multiple Spanning Tree or Rapid Spanning Tree.
If Rapid Spanning Tree protocol is in use, the
mstInstanceEditIndex is always 0. SEQUENCE OF XstInstanceCfgEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.4 |
xstInstanceCfgEntryA conceptual row containing the property of the RST or MST instance. XstInstanceCfgEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1 |
xstInstanceCfgIndexAn arbitrary integer within the range from 1 to the value of
the maximum instance that uniquely identifies a spanning
tree instance. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.1 |
xstInstanceCfgPriorityThe priority of a specific spanning tree instance.
The value assigned should be in the range 0-61440
in steps of 4096.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.2 |
xstInstanceCfgTimeSinceTopologyChangeThe time (in hundredths of a second) since the last topology
change detected by the bridge entity in RST or MST.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.3 |
xstInstanceCfgTopChangesThe total number of topology changes detected by
this bridge in RST or MST since the management entity
was last reset or initialized.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.4 |
xstInstanceCfgDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Multiple Spanning Tree Protocol. (802.1s)
or Rapid Spanning Tree Protocol (802.1w) executed by this node.
This value is used as the root identifier parameter in
all configuration bridge PDUs originated by this node.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.5 |
xstInstanceCfgRootCostThe cost of the path to the root as seen from
this bridge of the RST or MST.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.6 |
xstInstanceCfgRootPortThe number of the port which offers the
lowest cost path from this bridge to the root
bridge of the RST or MST.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.7 |
xstInstanceCfgMaxAgeThe maximum age of Multiple Spanning Tree Protocol (802.1s)
or Rapid Spanning Tree Protocol (802.1w) information learned
from the network on any port before it is discarded,
in units of hundredths of a second. This is the actual
value that this bridge is currently using.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.8 |
xstInstanceCfgHelloTimeThe amount of time between the transmission of
configuration bridge PDUs by this node on any port
when it is the root of the specific spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using in RST or MST.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.9 |
xstInstanceCfgHoldTimeThis time value determines the interval length
during which no more than two configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.10 |
xstInstanceCfgForwardDelayFor RST or MST protocol, this time value, measured in units of
hundredths of a second, controls how fast a port changes
its spanning state when moving towards the forwarding
state. The value determines how long the port
stays in each of the listening and learning
states, which precede the forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the forwarding database. This value is the
current value being used by the bridge.
xstInstanceCfgBridgeForwardDelay defines the value that
this bridge and all others would start using
if/when this bridge were to become the root.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.11 |
xstInstanceCfgBridgeMaxAgeFor RST or MST protocol, the time (in hundredths of second)
that all bridges use for MaxAge when this bridge is acting
as the root. Note that 802.1D-1990 specifies that the range
for this parameter is related to the value of
xstInstanceCfgBridgeHelloTime. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.12 |
xstInstanceCfgBridgeHelloTimeFor RST or MST protocol,the time (in hundredths of a second) that
all bridges use for HelloTime when this bridge is acting
as the root. The granularity of this timer is specified
by 802.1D-1990 to be 1 second.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.13 |
xstInstanceCfgBridgeForwardDelayFor RST or MST protocol, the time (in hundredths of a second)
that all bridges use for ForwardDelay when this bridge
is acting as the root.
Note that 802.1D-1990 specifies that the range for this
parameter is related to the value of
xstInstanceCfgBridgeMaxAge. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.14 |
xstInstanceCfgTxHoldCountFor RST or MST protocol, the value used by the port transmit
state machine to limit the maximum transmission rate.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.15 |
xstInstanceCfgPathCostMethodFor RST or MST protocol, this indicates the type of spanning tree path
cost mode used by the switch. The mode applies to all instances of the
Spanning Tree protocol running on the switch.
When the value of this MIB object is changed, the path cost
of all ports will be reassigned to the default path cost
values based on the new spanning tree path cost mode and the
ports' speed.
When the value of this MIB object is set to long(2),
the xstInstancePortPathCost MIB object must be used in order
to retrieve/configure the spanning tree port path cost as a
32-bit value. The set operation on dot1dStpPortPathCost in
BRIDGE-MIB will be rejected. While retrieving the value of
dot1dStpPortPathCost, the maximum value of 65535 will be
returned if the value of xstInstancePortPathCost for the same
instance exceeds 65535.
When the value of this MIB object is set to short(1),
the dot1dStpPortPathCost in BRIDGE-MIB must be used.ro StaPathCostMode .1.3.6.1.4.1.21839.2.2.26.1.5.6.4.1.16 |
xstInstancePortTableThe extension table for dot1dStpPortEntry to provide
additional Spanning Tree information and configuration. SEQUENCE OF XstInstancePortEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.5 |
xstInstancePortEntryThe conceptual row for xstInstancePortTable. XstInstancePortEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1 |
xstInstancePortPriorityDefines the priority used for this port in the Spanning
Tree Algorithm. If the path cost for all ports on a
switch is the same, the port with the highest priority
(i.e., lowest value) will be configured as an active link
in the Spanning Tree. This makes a port with higher
priority less likely to be blocked if the Spanning Tree
Algorithm is detecting network loops. Where more than one
port is assigned the highest priority, the port with
lowest numeric identifier will be enabled.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.3 |
xstInstancePortStateThe port's current state as defined by application of
the Spanning Tree Protocol. This state controls what
action a port takes on reception of a frame:
discarding(1): Port receives configuration messages,
but does not forward packets.
learning(2): Port has transmitted configuration messages
for an interval set by the Forward Delay
parameter without receiving contradictory
information. Port address table is cleared,
and the port begins learning addresses.
forwarding(3): Port forwards packets, and continues learning
addresses.
For ports which are disabled (see xstInstancePortEnable),
this object will have a value of discarding(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.4 |
xstInstancePortEnableThe enabled/disabled status of the port.ro EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.5 |
xstInstancePortDesignatedRootThe unique bridge identifier of the bridge
recorded as the root in the configuration BPDUs
transmitted by the designated bridge for the
segment to which the port is attached.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.7 |
xstInstancePortDesignatedCostThe path cost of the designated port of the
segment connected to this port. This value is
compared to the root path cost field in received
bridge PDUs.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.8 |
xstInstancePortDesignatedBridgeThe bridge identifier of the bridge which this
port considers to be the designated bridge for
this port's segment.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.9 |
xstInstancePortDesignatedPortThe port identifier of the port on the designated
bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.10 |
xstInstancePortForwardTransitionsThe number of times this port has transitioned
from the learning state to the forwarding state.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.11 |
xstInstancePortPortRoleThe role of the port in the RST or MST protocol:
(1) The port has no role within the spanning tree
(2) The port is part of the active topology connecting
the bridge to the root bridge (i.e., root port)
(3) The port is connecting a LAN through the bridge to the
root bridge (i.e., designated port)
(4) The port may provide connectivity if other
bridges, bridge ports, or LANs fail or are removed.
(5) The port provides backup if other
bridges, bridge ports, or LANs fail or are removed.
(6) For MST protocol only, indicates whether this instance
is in a master role.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.12 |
xstInstancePortAdminPathCostThe admin value of the MST internal pathcost,
in the range of 1 to 200000000.
This parameter is used to determine the best path between
devices. Therefore, lower values should be assigned to
ports attached to faster media, and higher values assigned
to ports with slower media. (Path cost takes precedence
over port priority).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.13 |
xstInstancePortOperPathCostThe oper value of the RST pathcost or MST internal pathcost,
in the range of 1 to 200000000.
This parameter is used to determine the best path between
devices. Therefore, lower values should be assigned to
ports attached to faster media, and higher values assigned
to ports with slower media. (Path cost takes precedence
over port priority).ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.5.1.14 |
mstInstanceEditTableThe Multiple Spanning Tree region instance vlan configuration table.
Please read the actual instance vlan mapped in the mstInstanceOperTable. SEQUENCE OF MstInstanceEditEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.6 |
mstInstanceEditEntryA conceptual row containing the status of the MSTP instance. MstInstanceEditEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.6.1 |
mstInstanceEditIndexAn arbitrary integer within the range from 1 to the value of
the maximum instance that uniquely identifies a spanning
tree instance. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.6.1.1 |
mstInstanceEditVlansMapA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with vlanIndex values
of 0 through 7; the second octet to VLANs 8 through
15; etc., The most significant bit of each octet
corresponds to the lowest value vlanIndex in that octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.
To create a row, write any of mstInstanceEditVlansMap,
mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or
mstInstanceEditVlansMap4k, to a non-empty list.
To destroy a row, write all of these four variables
to an empty list.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.6.1.2 |
mstInstanceEditVlansMap2kA string of octets containing one bit per VLAN for
VLANS with vlanIndex values of 1024 through 2047. The
first octet corresponds to VLANs with vlanIndex values
of 1024 through 1031; the second octet to VLANs 1032
through 1039; etc. The most significant bit of each
octet corresponds to the lowest value vlanIndex in that
octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.
To create a row, write any of mstInstanceEditVlansMap,
mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or
mstInstanceEditVlansMap4k, to a non-empty list.
To destroy a row, write all of these four variables
to an empty list.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.6.1.3 |
mstInstanceEditVlansMap3kA string of octets containing one bit per VLAN for
VLANS with vlanIndex values of 2048 through 3071. The
first octet corresponds to VLANs with vlanIndex values
of 2048 through 2055; the second octet to VLANs 2056
through 2063; etc. The most significant bit of each
octet corresponds to the lowest value vlanIndex in that
octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.
To create a row, write any of mstInstanceEditVlansMap,
mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or
mstInstanceEditVlansMap4k, to a non-empty list.
To destroy a row, write all of these four variables
to an empty list.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.6.1.4 |
mstInstanceEditVlansMap4kA string of octets containing one bit per VLAN for
VLANS with vlanIndex values of 3072 through 4095. The
first octet corresponds to VLANs with vlanIndex values
of 3072 through 3079; the second octet to VLANs 3080
through 3087; etc. The most significant bit of each
octet corresponds to the lowest value vlanIndex in that
octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.
To create a row, write any of mstInstanceEditVlansMap,
mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or
mstInstanceEditVlansMap4k, to a non-empty list.
To destroy a row, write all of these four variables
to an empty list.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.6.1.5 |
mstInstanceEditRemainingHopsThe remaining hop count for this MST instance.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.6.1.6 |
mstInstanceOperTableThe Multiple Spanning Tree region instance vlan mapped table. SEQUENCE OF MstInstanceOperEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.7 |
mstInstanceOperEntryA conceptual row containing the status of the MSTP instance. MstInstanceOperEntry .1.3.6.1.4.1.21839.2.2.26.1.5.6.7.1 |
mstInstanceOperIndexAn arbitrary integer within the range from 1 to the value of
the maximum instance that uniquely identifies a spanning
tree instance. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.6.7.1.1 |
mstInstanceOperVlansMapA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with vlanIndex values
of 0 through 7; the second octet to VLANs 8 through
15; etc., The most significant bit of each octet
corresponds to the lowest value vlanIndex in that octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.7.1.2 |
mstInstanceOperVlansMap2kA string of octets containing one bit per VLAN for
VLANS with vlanIndex values of 1024 through 2047. The
first octet corresponds to VLANs with vlanIndex values
of 1024 through 1031; the second octet to VLANs 1032
through 1039; etc. The most significant bit of each
octet corresponds to the lowest value vlanIndex in that
octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.7.1.3 |
mstInstanceOperVlansMap3kA string of octets containing one bit per VLAN for
VLANS with vlanIndex values of 2048 through 3071. The
first octet corresponds to VLANs with vlanIndex values
of 2048 through 2055; the second octet to VLANs 2056
through 2063; etc. The most significant bit of each
octet corresponds to the lowest value vlanIndex in that
octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.7.1.4 |
mstInstanceOperVlansMap4kA string of octets containing one bit per VLAN for
VLANS with vlanIndex values of 3072 through 4095. The
first octet corresponds to VLANs with vlanIndex values
of 3072 through 3079; the second octet to VLANs 3080
through 3087; etc. The most significant bit of each
octet corresponds to the lowest value vlanIndex in that
octet.
For each VLAN, if it is mapped to this MSTP instance,
then the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.5.6.7.1.5 |
staLoopbackDetectionPortTableA table provides the mechanism to configure the
spanning tree loopback detection of each port or trunk SEQUENCE OF StaLoopbackDetectionPortEntry .1.3.6.1.4.1.21839.2.2.26.1.5.8 |
staLoopbackDetectionPortEntryA conceptual row of staLoopbackDetectionPortTable. StaLoopbackDetectionPortEntry .1.3.6.1.4.1.21839.2.2.26.1.5.8.1 |
staLoopbackDetectionPortIfIndexThe port and the trunk interfaces of the portTable. The interface
identified by a particular value of this index is the same interface
as identified by the same value of ifIndex in the IF-MIB.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.8.1.1 |
staLoopbackDetectionPortStatusStatus of the port on whether spanning tree loopback detection is enabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.8.1.2 |
staLoopbackDetectionPortTrapStatusThe parameter indicates whether the trap has
to be sent when the loopback BPDUs have been detected.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.8.1.3 |
staLoopbackDetectionPortReleaseModeSetting it to auto(1) indicates that this port can be released
from discarding state automatically after loopback has occurred.
Setting it to manual(2) indicates that this port can be released
from discarding state manually after loopback has occurred.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.8.1.4 |
staLoopbackDetectionPortReleaseSet this to release(2) to release the port from discarding state.
noRelease(1) will always be obtained when reading this variable.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.8.1.5 |
staLoopbackDetectionPortShutdownIntervalSet the interval used when loopback detection action is
shutdown.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.5.8.1.7 |
staSystemBPDUFloodingGlobal BPDU flooding behavior configuration.
When BPDU is received on spanning tree disabled port.
(1) BPDU is flooded to all other spanning tree disabled ports in vlan that received BPDU.
(2) BPDU is flooded to all other spanning tree disabled ports.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.5.9 |
staCiscoPrestandardCompatibilityThe feature makes spanning tree operation compatible with Cisco
pre-standard versions.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.5.11 |
restartMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.7 |
restartOpCodeFileName of op-code file for start-up.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.7.1 |
restartConfigFileName of configuration file for start-up.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.7.2 |
restartControlSetting this object to warmBoot(2) causes the device to
reinitialize itself such that neither the agent configuration
nor the protocol entity implementation is altered. Setting this
object to coldBoot(3) causes the device to reinitialize itself such
that the agent's configuration or the protocol entity implementation
may be altered. When the device is running normally, this
variable has a value of running(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.7.3 |
mirrorMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.8 |
mirrorTableTable for port mirroring, enabling a port to be mirrored
to/from another port. Not all ports can be mirrored and
limitations may apply as to which ports can be used as either
source or destination ports. SEQUENCE OF MirrorEntry .1.3.6.1.4.1.21839.2.2.26.1.8.1 |
mirrorEntryThe conceptual row of mirrorTable. MirrorEntry .1.3.6.1.4.1.21839.2.2.26.1.8.1.1 |
mirrorDestinationPortThe destination port interface for mirrored packets.
The interface identified by a particular value of
this index is the same interface as identified by
the same value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.8.1.1.1 |
mirrorSourcePortThe source port interface for mirrored packets.
The interface identified by a particular value of
this index is the same interface as identified by
the same value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.8.1.1.2 |
mirrorTypeIf this value is rx(1), receive packets will
be mirrored. If this value is tx(2), transmit
packets will be mirrored. If this value is both(3),
both receive and transmit packets will be mirrored.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.8.1.1.3 |
mirrorStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.8.1.1.4 |
rspanTableA table that contains the settings of RSPAN. SEQUENCE OF RspanEntry .1.3.6.1.4.1.21839.2.2.26.1.8.3 |
rspanEntryThe conceptual row of rspanTable. RspanEntry .1.3.6.1.4.1.21839.2.2.26.1.8.3.1 |
rspanSessionIdThe session ID that may specify an entry in the table which
contains destination port(s) information. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.1 |
rspanSrcTxPortsSpecifies the source port list in tx mode.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.2 |
rspanSrcRxPortsSpecifies the source port list in rx mode.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.3 |
rspanDstPortThe port number of a destination port. The interface
identified by a particular value of this index is the same
interface as identified by the same value of ifIndex in the
IF-MIB.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.4 |
rspanDstPortTagSpecifies the traffic which is sent out from source port
with RSPAN VLAN ID or not.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.5 |
rspanSwitchRoleSpecifies the role of current switch.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.6 |
rspanRemotePortsSpecifies the uplink port list.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.7 |
rspanRemoteVlanIdSpecifies the ID of a RSPAN VLAN.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.8 |
rspanOperStatusThe operational status of the entry. A status of up(1)
means the setting of a session is complete and it has
started performing its function. A status of down(2) means
no function is performed because of incompleted session
setting.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.9 |
rspanStatusSet this to valid(1) to create an entry. Set this to
invalid(2) to destroy an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.8.3.1.10 |
igmpSnoopMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.9 |
igmpSnoopStatusParameter to enable or disable IGMP snooping on the device.
When enabled, the device will examine IGMP packets and set
up filters for IGMP ports.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.1 |
igmpSnoopQuerierEnables (disables) whether the switch acts as an IGMP
querier.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.2 |
igmpSnoopRouterPortExpireTimeSets the time (in seconds) the switch waits after
the previous querier has stopped querying before
the router port (which received query packets from
previous querier) expires.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.9.6 |
igmpSnoopVersionIGMP version snoopedrw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.9.7 |
igmpSnoopRouterCurrentTableTable for current router ports. SEQUENCE OF IgmpSnoopRouterCurrentEntry .1.3.6.1.4.1.21839.2.2.26.1.9.8 |
igmpSnoopRouterCurrentEntryEntry for current router ports. IgmpSnoopRouterCurrentEntry .1.3.6.1.4.1.21839.2.2.26.1.9.8.1 |
igmpSnoopRouterCurrentVlanIndexThe interface identified by a particular value of
this index is the same interface as identified by
the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
The entry will only appear here after a configure to
igmpSnoopRouterStaticTable. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.8.1.1 |
igmpSnoopRouterCurrentPortsThe set of ports which are current router ports, including static
router ports. Please refer to igmpSnoopRouterStaticTable.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.8.1.2 |
igmpSnoopRouterCurrentStatusThe set of ports which are static router ports.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.8.1.3 |
igmpSnoopRouterStaticTableTable for static router ports. SEQUENCE OF IgmpSnoopRouterStaticEntry .1.3.6.1.4.1.21839.2.2.26.1.9.9 |
igmpSnoopRouterStaticEntryEntry for static router ports. IgmpSnoopRouterStaticEntry .1.3.6.1.4.1.21839.2.2.26.1.9.9.1 |
igmpSnoopRouterStaticVlanIndexThe interface identified by a particular value of
this index is the same interface as identified by
the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
The entry will only appear here after a configure to
igmpSnoopRouterStaticTable. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.9.1.1 |
igmpSnoopRouterStaticPortsThe set of ports which are static router ports.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.9.1.2 |
igmpSnoopRouterStaticStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.9.9.1.3 |
igmpSnoopMulticastStaticTableTable for static multicast addresses. SEQUENCE OF IgmpSnoopMulticastStaticEntry .1.3.6.1.4.1.21839.2.2.26.1.9.11 |
igmpSnoopMulticastStaticEntryEntry for static multicast addresses. IgmpSnoopMulticastStaticEntry .1.3.6.1.4.1.21839.2.2.26.1.9.11.1 |
igmpSnoopMulticastStaticVlanIndexThe interface identified by a particular value of
this index is the same interface as identified by
the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
The entry will only appear here after a configure to
igmpSnoopMulticastStaticTable. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.11.1.1 |
igmpSnoopMulticastStaticIpAddressIP address of multicast group. IpAddress .1.3.6.1.4.1.21839.2.2.26.1.9.11.1.2 |
igmpSnoopMulticastStaticPortsThe set of ports which are members.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.11.1.3 |
igmpSnoopMulticastStaticStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.9.11.1.4 |
igmpSnoopCurrentVlanTableTable for enabling or disabling IGMP snooping per VLAN. SEQUENCE OF IgmpSnoopCurrentVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.9.14 |
igmpSnoopCurrentVlanEntryEntry for enabling or disabling IGMP snooping. IgmpSnoopCurrentVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.9.14.1 |
igmpSnoopCurrentVlanIndexSame is dot1qVlanIndex in the Q-BRIDGE-MIB.
This table has only one entry - the entry for
the VLAN of the management interface. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.1 |
igmpSnoopCurrentVlanStatusParameter to enable or disable IGMP snooping on this VLAN.
When enabled, the device will examine IGMP packets and set
up filters for IGMP ports.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.2 |
igmpSnoopCurrentVlanImmediateLeaveThe parameter to enable or disable the Immediate-Leave feature on this VLAN.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.3 |
igmpSnoopCurrentVlanGeneralQuerySuppressionThe parameter to enable or disable the general query suppresion
on this VLAN.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.4 |
igmpSnoopCurrentVlanLastMemQueryCountRepresents the number of queries sent by the switch before
it assumes there are no local members.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.5 |
igmpSnoopCurrentVlanLastMemQueryIntvlThe last member query interval is the max response time
inserted into group-specific queries sent in response to
leave group messages,and is also the the max response time
inserted into group-and-source-specific query messages.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.6 |
igmpSnoopCurrentVlanProxyAddressRepresents the address of queries sent by the switch.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.7 |
igmpSnoopCurrentVlanQueryIntvlRepresents the query interval of queries sent by the switch.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.8 |
igmpSnoopCurrentVlanQueryRespIntvlRepresents the query response interval of queries
sent by the switch.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.9 |
igmpSnoopCurrentVlanProxyReportingSet this variable to enabled(1) to enable the feature.
Set this variable to disabled(2) to disable the feature.
Set this variable to default(3), the status of the feature
is decided by the global configuration.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.10 |
igmpSnoopCurrentVlanVersionthe version of igmp packets is supported by this vlan.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.11 |
igmpSnoopCurrentVlanVersionExclusiveEnable/disable control of the IGMP Snooping exclusive
supported version.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.12 |
igmpSnoopCurrentVlanImmediateLeaveByHostIpThe parameter to enable or disable the Immediate-Leave feature by host ip on this VLAN.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.14.1.14 |
igmpSnoopMulticastGroupTableTable for current multicast addresses. SEQUENCE OF IgmpSnoopMulticastGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.9.15 |
igmpSnoopMulticastGroupEntryEntry for Group multicast addresses. IgmpSnoopMulticastGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.9.15.1 |
igmpSnoopMulticastGroupVlanIndexThe interface identified by a particular value of
this index is the same interface as identified by
the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.
The entry will only appear here after a configure to
igmpSnoopMulticastStaticTable. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.15.1.1 |
igmpSnoopMulticastGroupIpAddressIP address of multicast group. IpAddress .1.3.6.1.4.1.21839.2.2.26.1.9.15.1.2 |
igmpSnoopMulticastGroupSourceIPAddressSource IP address of source. IpAddress .1.3.6.1.4.1.21839.2.2.26.1.9.15.1.3 |
igmpSnoopMulticastGroupPortsThe set of ports which are members of a multicast group, including
static members. Please refer to igmpSnoopMulticastStaticTable.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.15.1.4 |
igmpSnoopMulticastGroupStatusThe set of ports which are static IGMP member ports.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.15.1.5 |
igmpSnoopMulticastGroupPortCountThe number of forwarding port in this groupro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.15.1.6 |
igmpSnoopReportSuppressionStatusParameter to enable or disable IGMP snooping report suppression on the device.
When enabled, the device will suppress superabundance report and leave packets.
Only the First copy of Report Packet or the Last copy of Leave Packet for the
same Group will be forwarded to route ports.
Status changed to deprecated:this function is always enable.rwdeprecated EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.16 |
igmpSnoopFilterStatusParameter to enable or disable IGMP filtering on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.17 |
igmpSnoopProfileTableThe table for configuring the IGMP snooping profile. SEQUENCE OF IgmpSnoopProfileEntry .1.3.6.1.4.1.21839.2.2.26.1.9.18 |
igmpSnoopProfileEntryThe entry for configuring the IGMP snooping profile. IgmpSnoopProfileEntry .1.3.6.1.4.1.21839.2.2.26.1.9.18.1 |
igmpSnoopProfileIdThe ID of the IGMP snooping profile. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.18.1.1 |
igmpSnoopProfileActionThe access mode of the IGMP snooping profile.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.18.1.2 |
igmpSnoopProfileStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.9.18.1.3 |
igmpSnoopProfileCtl OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.9.19 |
igmpSnoopProfileCtlIdThe ID of the IGMP snooping profile. The default value
is zero, meaning that no ID is specified. In order to
create a profile, a non-zero value must be specified.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.19.1 |
igmpSnoopProfileCtlInetAddressTypeThe address type is associated with this agent.
Only ipv4(1) type is supported.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.19.2 |
igmpSnoopProfileCtlStartInetAddressThe specified addresses in the start of the controlled
IP multicast addresses.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.19.3 |
igmpSnoopProfileCtlEndInetAddressThe specified addresses in the end of the controlled
IP multicast addresses.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.19.4 |
igmpSnoopProfileCtlActionSetting it to create(2) creates the range of the
controlled IP multicast addresses.
Setting it to destroy(3) destroys the range of the
controlled IP multicast addresses.
When the action is completed, this object becomes
noAction(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.19.5 |
igmpSnoopProfileRangeTableThe table for configuring the range of the IGMP snooping
profile. SEQUENCE OF IgmpSnoopProfileRangeEntry .1.3.6.1.4.1.21839.2.2.26.1.9.20 |
igmpSnoopProfileRangeEntryThe entry for configuring the range of the IGMP snooping
profile. IgmpSnoopProfileRangeEntry .1.3.6.1.4.1.21839.2.2.26.1.9.20.1 |
igmpSnoopProfileRangeProfileIdThis is defined as igmpSnoopProfileId. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.20.1.1 |
igmpSnoopProfileRangeInetAddressTypeThe address type is associated with this agent.
Only ipv4(1) type is supported. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.20.1.2 |
igmpSnoopProfileRangeStartInetAddressThe specified addresses in the start of the controlled
IP multicast addresses. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.20.1.3 |
igmpSnoopProfileRangeEndInetAddressThe specified addresses in the end of the controlled
IP multicast addresses.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.20.1.4 |
igmpSnoopProfileRangeActionThe access mode of the IGMP snooping profile.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.20.1.5 |
igmpSnoopFilterPortTableTable for port configuration in IGMP filtering. SEQUENCE OF IgmpSnoopFilterPortEntry .1.3.6.1.4.1.21839.2.2.26.1.9.21 |
igmpSnoopFilterPortEntryEntry for port configuration in IGMP filtering. IgmpSnoopFilterPortEntry .1.3.6.1.4.1.21839.2.2.26.1.9.21.1 |
igmpSnoopFilterPortIndexThe port and trunk (including trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface identified by the same
value of ifIndex in the IF-MIB. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.21.1.1 |
igmpSnoopFilterPortProfileIdThe igmpSnoopProfileEntry identified by a particular value of this index
is the same interface identified by the same value of the igmpSnoopProfileId
object. If there is no corresponding entry in the igmpSnoopProfileTable,
then no association exists. In particular, if this value is zero, no
associated profile will be generated, as zero is not a valid profile index.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.9.21.1.2 |
igmpSnoopThrottlePortTableTable for port configuration in IGMP throttling. SEQUENCE OF IgmpSnoopThrottlePortEntry .1.3.6.1.4.1.21839.2.2.26.1.9.22 |
igmpSnoopThrottlePortEntryEntry for port configuration in IGMP throttling. IgmpSnoopThrottlePortEntry .1.3.6.1.4.1.21839.2.2.26.1.9.22.1 |
igmpSnoopThrottlePortIndexThe port and trunk (including trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface identified by the same
value of ifIndex in the IF-MIB. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.22.1.1 |
igmpSnoopThrottlePortRunningStatusDescribes the running status of the IGMP throttling to the switch.
A value of true(1) indicates the IGMP throttling mechanism is active.
A value of false(2) indicates the IGMP throttling mechanism is inactive.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.9.22.1.2 |
igmpSnoopThrottlePortActionThe action mode of the IGMP throttling. A value of replace(1)
means to replace a joined multicast group randomly when an interface
receives an IGMP report and the number of current joined multicast groups
is equal to the maximum number of IGMP groups that the interface can join.
A value of deny(2) means to deny the IGMP report request when an interface
receives an IGMP report and the number of current joined multicast groups
is equal to the maximum number of IGMP groups that the interface can join.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.22.1.3 |
igmpSnoopThrottlePortMaxGroupsThe maximum number of IGMP groups that the interface can join.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.9.22.1.4 |
igmpSnoopThrottlePortCurrentGroupsThe current number of IGMP groups that the interface has joined.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.9.22.1.5 |
igmpSnoopPortTableTable of IGMP Snooping service per port. SEQUENCE OF IgmpSnoopPortEntry .1.3.6.1.4.1.21839.2.2.26.1.9.27 |
igmpSnoopPortEntryEntry of IGMP Snooping service per port. IgmpSnoopPortEntry .1.3.6.1.4.1.21839.2.2.26.1.9.27.1 |
igmpSnoopPortIndexThe port and the trunk (excluding trunk members)
interface of the igmpSnoopPortTable. The interface
identified by a particular value of this index
is the same interface as identified by the same
value of ifIndex in the IF-MIB. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.1 |
igmpSnoopQueryDropParameter to enable or disable dropping IGMP Query packet.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.3 |
igmpSnoopMulticastDataDropParameter to enable or disable dropping IP multicast datarw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.4 |
igmpSnoopPortNumGroupsCurrent learned groupsro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.5 |
igmpSnoopPortNumJoinSendNumber of join sendro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.6 |
igmpSnoopPortNumJoinsNumber of join recievedro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.7 |
igmpSnoopPortNumJoinSuccessNumber of join group successro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.8 |
igmpSnoopPortNumLeavesSendNumber of leave sendro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.9 |
igmpSnoopPortNumLeavesNumber of leave receivedro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.10 |
igmpSnoopPortNumGeneralQuerySendNumber of general query send.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.11 |
igmpSnoopPortNumGeneralQueryReceviedNumber of general query received.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.12 |
igmpSnoopPortNumSepcificQuerySendNumber of specific query send.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.13 |
igmpSnoopPortNumSpecificQueryReceivedNumber of specific query received.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.14 |
igmpSnoopPortNumInvalidReportNumber of invalid report received.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.15 |
igmpSnoopPortClearStatisticsClear this VLAN all statisticsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.9.27.1.16 |
igmpSnoopGlobalMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.9.28 |
igmpSnoopProxyReportingParameter to enable or disable IGMP snooping proxy reporting
on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.28.1 |
igmpSnoopRouterAlertOptionCheckParameter to enable or disable IGMP snooping router alert
option check on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.28.2 |
igmpSnoopTcnFloodParameter to enable or disable IGMP snooping tcn flood
on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.28.3 |
igmpSnoopTcnQuerySolicitParameter to enable or disable IGMP snooping tcn query
solicit on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.28.4 |
igmpSnoopUnregisteredDataFloodParameter to enable or disable IGMP snooping Unregistered
data flood solicit on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.28.5 |
igmpSnoopUnsolicitedReportIntervalSetting this value to specify how long (in seconds) the
uplink ports should transmit unsolicited reports.rw Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.28.6 |
igmpSnoopVersionExclusiveParameter to enable or disable IGMP snooping version
exclusive on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.28.7 |
igmpSnoopMrouterForwardModeParemete to set IGMP snooping Mrouter port forward mode.
When set dynamic, IGMP snooping Mrouter port won't forward multicast streams received from other mrouter port.
When set forward, IGMP snooping Mrouter port will forward multicast streams received from other mrouter port.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.9.28.8 |
igmpSnoopForwardingPriorityConfigure IGMP snooping multicast stream forwarding priority.
If value is 65535, it means the priority is disabledrw Integer32(0..7|65535) .1.3.6.1.4.1.21839.2.2.26.1.9.29 |
igmpSnoopQueryDropTableTable of IGMP Snooping query drop per vlan and per vlan configuration. SEQUENCE OF IgmpSnoopQueryDropEntry .1.3.6.1.4.1.21839.2.2.26.1.9.30 |
igmpSnoopQueryDropEntryEntry of IGMP Snooping service per port and per VLAN. IgmpSnoopQueryDropEntry .1.3.6.1.4.1.21839.2.2.26.1.9.30.1 |
igmpSnoopQueryDropPortIndexThe port and the trunk (excluding trunk members)
interface of the igmpSnoopPortTable. The interface
identified by a particular value of this index
is the same interface as identified by the same
value of ifIndex in the IF-MIB. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.30.1.1 |
igmpSnoopQueryDropVlanBitmapThe VLAN bitmap which query drop applied on this port.
If all zero, it means disable,
For all VLAN, please use igmpSnoopPortTable to configure.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.9.30.1.2 |
igmpSnoopClearDynamicGroupsClear all IGMP groups which are learned by IGMP report and MVR.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.9.32 |
igmpSnoopVlanTableTable of IGMP Snooping service per port. SEQUENCE OF IgmpSnoopVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.9.33 |
igmpSnoopVlanEntryEntry of IGMP Snooping service per VLAN. IgmpSnoopVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.9.33.1 |
igmpSnoopVlanIndexVLAN ID VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.1 |
igmpSnoopVlanNumGroupsCurrent learned groupsro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.2 |
igmpSnoopVlanNumJoinSendNumber of join send.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.3 |
igmpSnoopVlanNumJoinsNumber of join receivedro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.4 |
igmpSnoopVlanNumJoinSuccessNumber of jion successro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.5 |
igmpSnoopVlanNumLeavesSendNumber of leave send.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.6 |
igmpSnoopVlanNumLeavesNumber of leave receivedro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.7 |
igmpSnoopVlanNumGeneralQuerySendNumber of general query sendro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.8 |
igmpSnoopVlanNumGeneralQueryReceviedNumber of general query receivedro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.9 |
igmpSnoopVlanNumSepcificQuerySendNumber of specific query sendro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.10 |
igmpSnoopVlanNumSpecificQueryReceivedNumber of sepcific query receivedro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.11 |
igmpSnoopVlanNumInvalidReportNumber of invalid report receivedro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.12 |
igmpSnoopVlanClearStatisticsClear this VLAN statisticsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.9.33.1.13 |
ipMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.10 |
netDefaultGatewayThe IP Address of the default gateway. If this value is
undefined or unknown, it shall have the value 0.0.0.0.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.10.2 |
ipHttpStateWhether HTTP is enabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.10.3 |
ipHttpPortThe port number for HTTP.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.4 |
ipDhcpRestartWhen set to restart(1) the DHCP server will restart. When read,
this value always returns noRestart(2).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.5 |
ipHttpsStateWhether HTTPS is enabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.10.6 |
ipHttpsPortThe port number for HTTPS.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.7 |
dhcpMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.10.11 |
dhcpClient OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.10.11.1 |
dhcpcOptions OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.10.11.1.1 |
dhcpcInterfaceTableTable for DHCP client information listed by interface.
Depending on the nature of the product, this table may
have only one entry(e.g. for the management VLAN), or
may have many entries(e.g. for all ports, or for all
static VLANs). SEQUENCE OF DhcpcInterfaceEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.1.1.1 |
dhcpcInterfaceEntryEntry for DHCP client information listed by interface. DhcpcInterfaceEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.1.1.1.1 |
dhcpcIfIndexThis is defined by ifIndex in the IF-MIB.(static vlan if index) Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.11.1.1.1.1.1 |
dhcpcIfVendorClassIdModeWhether the vendor class ID is in text mode or in
Hex mode.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.11.1.1.1.1.4 |
dhcpcIfVendorClassIdThe value that the DHCP client sets in the vendor
class_id option of DHCPDISCOVER and DHCPREQUEST messages.
This value may be used by DHCP servers to identify vendor
classof the client.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.10.11.1.1.1.1.5 |
dhcpRelay OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.10.11.2 |
dhcpRelayRestartSet this object to restart(1) to restart DCHP Relay.
Always get noRestart(2) when you read this variable.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.3 |
dhcpRelayServerInetAddrTableThe role of DHCP Relay Agent is to forward requests and replies
between server and client when they are not in the same subnet. To
enable DHCP Relay service user needs to specify Relay Server IP
address and then restart DHCP Relay. This Table is to specify Relay
Server IP address,the maximum numbers of server IP address user can
specify is 5.To Restart DHCP Relay, please use the dhcpRelayRestart
variable. SEQUENCE OF DhcpRelayServerInetAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.4 |
dhcpRelayServerInetAddrEntryA conceptual row of dhcpRelayServerAddrTable. DhcpRelayServerInetAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.4.1 |
dhcpRelayServerInetAddrIfIndexThe VLAN interface being used by this table entry. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.4.1.1 |
dhcpRelayServerInetAddrIndexThe Index of the Relay server IP address. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.4.1.2 |
dhcpRelayServerInetAddressTypeThe INET address type of the relay server.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.4.1.3 |
dhcpRelayServerInetAddressThe INET address of the relay server.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.4.1.4 |
dhcpv6RelayServerInetAddrTableThe role of DHCP Relay Agent is to forward requests and replies
between server and client when they are not in the same subnet. To
enable DHCP Relay service user needs to specify Relay Server IPv6
address. This Table is to specify Relay Server IPv6 address,
the maximum numbers of server IPv6 address user can specify is 5. SEQUENCE OF Dhcpv6RelayServerInetAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.5 |
dhcpv6RelayServerInetAddrEntryA conceptual row of dhcpv6RelayServerAddrTable. Dhcpv6RelayServerInetAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.5.1 |
dhcpv6RelayServerInetAddrIfIndexThe VLAN interface being used by this table entry. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.5.1.1 |
dhcpv6RelayServerInetAddressThe INET address of the relay server.rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.5.1.2 |
dhcpv6RelayServerVlanTableThe role of DHCP Relay Agent is to forward requests and replies
between server and client when they are not in the same subnet. To
enable DHCP Relay service user needs to specify multicast Relay Server Vlan.
This Table is to specify multicast Relay Server Vlan. SEQUENCE OF Dhcpv6RelayServerVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.6 |
dhcpv6RelayServerVlanEntryA conceptual row of dhcpv6RelayServerVlanTable. Dhcpv6RelayServerVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.6.1 |
dhcpv6RelayServerVlanIfIndexThe relay VLAN interface. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.6.1.1 |
dhcpv6RelayServerMcastIfIndexThe multicast relay destination VLAN interface. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.6.1.2 |
dhcpv6RelayServerVlanEnableThe status of multicast relay destination VLAN interface.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.10.11.2.6.1.3 |
dhcpOption82 OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.10.11.4 |
dhcpOption82StatusSet enabled(1) to enable DHCP Relay Option 82,
set disabled(2) to disable it.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.1 |
dhcpOption82PolicyProvide three policies to handle packetrw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.2 |
dhcpOption82RemoteIDModeProvide five mode for insertion remote-id sub-option of option 82.
If configured-string(5) has been set, dhcpOption82RemoteIDString
will take effect.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.3 |
dhcpOption82RemoteIDStringSet string to remote-id sub-option of option 82.
It only take effect when dhcpOption82RemoteIDMode is set to configured-string(5)rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.4 |
dhcpOption82EncodeFormatSet encode format for CID and RID in option82.
Set extra-subtype-included(1) will have extra subtype and length field in CID and RID.
Set no-extra-subtype-included(2) will only have TLV format for CID and RID.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.5 |
dhcpOption82RelayServerAddrTableThis table is to specify relay server IP address,
the maximum number of server IP addresses user can specify is 5. SEQUENCE OF DhcpOption82RelayServerAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.6 |
dhcpOption82RelayServerAddrEntryA conceptual row of dhcpOption82RelayServerAddrTable. DhcpOption82RelayServerAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.6.1 |
dhcpOption82RelayServerAddrIndexThe index of the relay server IP address. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.6.1.1 |
dhcpOption82RelayServerAddrServerIpThe IP address of the relay server.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.10.11.4.6.1.2 |
dhcpDynamicProvisionStatusA per-system enable/disable configuration to decide whether to use
the specified configuration file in DHCP packet. It shall use the specified
configuration file in DHCP packet if this configuration is disabled and the
start-up configuration file is Factory_Default_Config.cfg.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.10.11.6 |
pingMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.10.15 |
pingIpAddressSpecifies the IP address of the device that is planned
to ping.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.10.15.1 |
pingPacketSizeSpecifies the size of each data potion of ping packets
in bytes.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.15.2 |
pingCompletedA value of true(1) will be read when this ping operation has
been either responded to or changed to the time-out status.
A value of false(2) will be read when there is a ping
operation running and all associated objects in the pingMgt
operation cannot be modified during this period.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.10.15.4 |
pingActionThe action of the pingMgt operation. Sets these objects to
pingStart(2) to begin the ping operation. Once the action
is set to pingStart(2), the associated pingMgt objects cannot
be modified until this ping operation is completed
(pingCompleted is true). When the ping has ended or there is
no ping operation performing, this object will get a value of
noAction(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.15.5 |
pingProbeCountSpecifies the number of times to perform a ping operation at a
remote host.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.10.15.6 |
pingSentPacketsThe value of this object reflects the number of probes sent.
The value of this object must be reported as 0 when no probes
have been sent.ro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.10.15.7 |
pingReceivedPacketsNumber of responses received. The value of this object must
be reported as 0 when no probe responses have been received.ro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.10.15.8 |
pingPacketLossRatePacket loss rate of this ping operation. This variable is
calculated by pingReceivedPackets and pingSentPackets. The
rate is expressed as a percentage.ro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.10.15.9 |
pingHistoryTableContains the executive result information for the ping
operation. SEQUENCE OF PingHistoryEntry .1.3.6.1.4.1.21839.2.2.26.1.10.15.10 |
pingHistoryEntryA conceptual row in the pingHistory table. PingHistoryEntry .1.3.6.1.4.1.21839.2.2.26.1.10.15.10.1 |
pingHistoryIndexA new entry in this table is created when the result of
a ping probe is determined. The old entries will be cleared
when a new ping action is started. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.15.10.1.1 |
pingHistoryResponseThis variable represents the round trip time and is
measured in milliseconds. The variable is the difference
between received time and sent time for a ping probe. If
the difference value is more than the time-out value or no
response is received, then the variable will be 5000
milliseconds.ro Integer32 UNITS "milliseconds" .1.3.6.1.4.1.21839.2.2.26.1.10.15.10.1.2 |
iPAddrTableA table of iPAddrEntry. SEQUENCE OF IPAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.16 |
iPAddrEntryA set of configuration parameters for a particular
network interface on this device. If the device has no network
interface, this table is empty.
The index is composed of the ifIndex assigned to the
corresponding interface. IPAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.10.16.1 |
iPAddrIfIndexThe VLAN interface being used by this table entry. Only the
VLAN interfaces which have an IP configured will appear in
the table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.10.16.1.1 |
iPAddrIPAddressThe IP address of this Net interface. The default value
for this object is 0.0.0.0. If either the IPAddrIPAddress
or IPAddrSubnetMask is 0.0.0.0, then when the device
boots, it may use BOOTP to try to figure out what these
values should be. If BOOTP fails, before the device
can talk on the network, this value must be configured
(e.g., through a terminal attached to the device). IpAddress .1.3.6.1.4.1.21839.2.2.26.1.10.16.1.2 |
iPAddrSubnetMaskThe subnet mask of this Net interface. The default value
for this object is 0.0.0.0. If either the IPAddrIPAddress
or IPAddrSubnetMask are 0.0.0.0, then when the device
boots, it may use BOOTP to try to figure out what these
values should be. If BOOTP fails, before the device
can talk on the network, this value must be configured
(e.g., through a terminal attached to the device). IpAddress .1.3.6.1.4.1.21839.2.2.26.1.10.16.1.3 |
iPAddrPrimaryInterfaceWhether this is a primary interface.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.16.1.4 |
iPAddrUnnumberedWhether this is an unnumbered interface.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.16.1.5 |
iPAddrStatusThe status of this conceptual row entry. This object isused to manage the
creation and deletion of conceptual rows.
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has value 'active');
it is not available for use by the managed device, though
the agent has sufficient information to make it so (the
status column has value 'notInService'); or, it is not
available for use by the managed device, and an attempt to
make it so would fail because the agent has insufficient
information (the state column has value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.10.16.1.6 |
ipHttpsDeleteCertificateTo delete current HTTPS certificate in flash,
write this variable to delete(1). Writing this variable
to noDelete(2) has no effect on the device. When
read, this variable always returns noDelete(2).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.10.18 |
vlanMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.12 |
vlanTableTable for VLAN configuration. SEQUENCE OF VlanEntry .1.3.6.1.4.1.21839.2.2.26.1.12.1 |
vlanEntryEntry for VLAN configuration. VlanEntry .1.3.6.1.4.1.21839.2.2.26.1.12.1.1 |
vlanIndexBased on dot1qVlanIndex in the Q-BRIDGE-MIB.
This table has only one entry - the entry for
the VLAN of the management interface. Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.12.1.1.1 |
vlanAddressMethodMethod to get the IP address.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.1.1.2 |
vlanPortTableTable for port configuration in VLAN. SEQUENCE OF VlanPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.2 |
vlanPortEntryEntry for port configuration in VLAN. VlanPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.2.1 |
vlanPortIndexThe port and the trunk (excluding trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by the same
value of dot1qPvid in the Q-BRIDGE-MIB. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.12.2.1.1 |
vlanPortModeThis variable sets the 802.1Q VLAN mode.
Setting it to hybrid(1) sets a hybrid link.
Setting it to dot1qTrunk(2) sets a trunk link.
Setting it to access(3) sets an access link.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.2.1.2 |
voiceVlanMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.12.6 |
voiceVlanOuiTableA table containing the mac address which can be identified
by Voice VLAN. SEQUENCE OF VoiceVlanOuiEntry .1.3.6.1.4.1.21839.2.2.26.1.12.6.1 |
voiceVlanOuiEntryA table containing the mac address which can be identified
by Voice VLAN. VoiceVlanOuiEntry .1.3.6.1.4.1.21839.2.2.26.1.12.6.1.1 |
voiceVlanOuiAddressMAC address can be identified by voice vlan.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.12.6.1.1.1 |
voiceVlanOuiMaskThe mask of MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.12.6.1.1.2 |
voiceVlanOuiDescriptionThe description of OUI.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.12.6.1.1.3 |
voiceVlanOuiStatusCurrent operation status of the row.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.12.6.1.1.4 |
voiceVlanEnabledIdVoice VLAN enabled status and VLAN ID:
enabled (1..4093), disabled (-1).rw INTEGER (-1|1..4093) .1.3.6.1.4.1.21839.2.2.26.1.12.6.2 |
voiceVlanAgingTimeVoice VLAN aging time, the unit of which is minute.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.12.6.3 |
voiceVlanPortTableA list of voice VLAN port entries. SEQUENCE OF VoiceVlanPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.6.7 |
voiceVlanPortEntryAn entry containing Voice VLAN port information,
which is applicable to a Voice VLAN enabled interface. VoiceVlanPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1 |
voiceVlanPortIfIndexThe index of interface on which Voice VLAN function
is enabled. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1.1 |
voiceVlanPortModeVoice VLAN configuration mode status.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1.2 |
voiceVlanPortSecurityIf the security is enabled, the port only allows voice
traffic for the Voice VLAN.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1.3 |
voiceVlanPortPriorityThe priority of the voice vlan traffic in the port.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1.4 |
voiceVlanPortRuleOuiThe address of voice device is learned from
OUI table.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1.5 |
voiceVlanPortRuleLldpThe address of voice device is learned from
LLDP discovery.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1.6 |
voiceVlanPortRemainAgeRemaining aging time, the unit of which is minute.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.12.6.7.1.7 |
vlanDot1qTunnelGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.12.8 |
vlanDot1qTunnelStatusThis parameter is used to globally enable/disable
802.1Q Tunneling on the device.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.12.8.1 |
vlanDot1qTunnelPortTableTable for port configuration in 802.1Q Tunneling. SEQUENCE OF VlanDot1qTunnelPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.9 |
vlanDot1qTunnelPortEntryEntry for port configuration in 802.1Q Tunneling. VlanDot1qTunnelPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.9.1 |
vlanDot1qTunnelPortIndexThe port and the trunk (excluding trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by the same
value of ifIndex in the IF-MIB. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.12.9.1.1 |
vlanDot1qTunnelPortModeThis variable sets the 802.1Q Tunneling mode.
Setting it to none(1) indicates no mode in this port.
Setting it to access(2) sets as dot1q-tunnel mode port which links to customer.
Setting it to uplink(3) sets as dot1q-tunnel mode port which links to service-provider.
If vlanDot1qTunnelStatus is disabled, it means vlanDot1qTunnelPortMode is inactive.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.9.1.2 |
vlanDot1qTunnelPortEtherTypeTPID for 802.1Q encapsulation. It's used to select a nonstandard
(nondefault) 2-byte ethertype to identify 802.1Q tagged frames.rw Unsigned32 ('0800'h..'ffff'h) .1.3.6.1.4.1.21839.2.2.26.1.12.9.1.3 |
vlanDot1qTunnelPortPriorityMapStatusStatus of priority mapping. Set to enabled(1) to use 802.1p
priority of inner tag as packet's priority instead of using
outer tag.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.12.9.1.4 |
dot1vProtocolExPortTableA table that contains protocol Vlan priority information. SEQUENCE OF Dot1vProtocolExPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.10 |
dot1vProtocolExPortEntryA list of protocol VLAN user priority sets for each port. Dot1vProtocolExPortEntry .1.3.6.1.4.1.21839.2.2.26.1.12.10.1 |
dot1vProtocolExPortGroupPrioritySpecifies the priority in the added tag for qualified frames.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.12.10.1.1 |
macVlanTableA table that contains the settings for MAC-based VLAN. SEQUENCE OF MacVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.12.11 |
macVlanEntryA conceptual row in the macVlanTable. MacVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.12.11.1 |
macVlanMacAddressThe MAC address that may specify an entry in the table
which contains MAC-based VLAN information. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.12.11.1.1 |
macVlanIdSpecifies the VLAN ID which the MAC address associates
with.rw VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.12.11.1.2 |
macVlanPrioritySpecifies the priority whcich the MAC address associates
with.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.12.11.1.3 |
macVlanStatusSet this to valid(1) to create an entry. Set this to
invalid(2) to destroy an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.12.11.1.4 |
macVlanMacMaskThe MAC address mask that may specify an entry in the table
which contains MAC-based VLAN information. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.12.11.1.5 |
macVlanClearActionAction for clearing macVlanTable. When this object is set
to clear(2), all entries in macVlanTable will be cleared.
When this object is read, the value of this object is
always noClear(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.12 |
subnetVlanTableA table that contains the settings for IP subnet-based
VLAN. SEQUENCE OF SubnetVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.12.13 |
subnetVlanEntryA conceptual row in the subnetVlanTable. SubnetVlanEntry .1.3.6.1.4.1.21839.2.2.26.1.12.13.1 |
subnetVlanIpAddressThe IPv4 address of a subnet. Any assignment (implicit or
otherwise) of an instance of this object to a value x must
be rejected if the bitwise logical-AND of x with the value
of the corresponding instance of the subnetVlanMask object
is not equal to x. IpAddress .1.3.6.1.4.1.21839.2.2.26.1.12.13.1.1 |
subnetVlanMaskThe netmask of a subnet. Any assignment (implicit or
otherwise) of an instance of this object to a value x must
be rejected if the bitwise logical-AND of x with the value
of the corresponding instance of the subnetVlanIpAddress
object is not equal to subnetVlanIpAddress. IpAddress .1.3.6.1.4.1.21839.2.2.26.1.12.13.1.2 |
subnetVlanIdSpecifies the VLAN ID which the subnet associates with.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.12.13.1.3 |
subnetVlanPrioritySpecifies the priority whcich the subnet associates with.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.12.13.1.4 |
subnetVlanStatusSet this to valid(1) to create an entry. Set this to
invalid(2) to destroy an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.12.13.1.5 |
subnetVlanClearActionAction for clearing subnetVlanTable. When this object is
set to clear(2), all entries in subnetVlanTable will be
cleared. When this object is read, the value of this object
is always noClear(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.14 |
vlanStaticExtTableThe extension table of dot1qVlanStaticTable. This table
enhances the original table with extra
vlanStaticExtRspanStatus to create and destroy RSPAN
VLAN(s). SEQUENCE OF VlanStaticExtEntry .1.3.6.1.4.1.21839.2.2.26.1.12.15 |
vlanStaticExtEntryA conceptual row in the vlanStaticExtTable. VlanStaticExtEntry .1.3.6.1.4.1.21839.2.2.26.1.12.15.1 |
vlanStaticExtRspanStatusDisplays type of a VLAN is vlan(2) or rspanVlan(3). Set
this to destroy(1) to destroy a RSPAN VLAN. Set this to
rspanVlan(3) to create a RSPAN VLAN. Setting this to
vlan(2) is not allowed.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.15.1.1 |
vlanStaticTableTable for static VLAN configuration including VLAN aggregation support. SEQUENCE OF VlanStaticEntry .1.3.6.1.4.1.21839.2.2.26.1.12.17 |
vlanStaticEntryStatic information for a VLAN configured on the device by (local or
network) management. VlanStaticEntry .1.3.6.1.4.1.21839.2.2.26.1.12.17.1 |
vlanStaticIndexThe VLAN ID of the VLAN. VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.12.17.1.1 |
vlanStaticInterfaceTypeThe interface type of the VLAN (there is a subtype of IANAifType).
l2vlan(135) refers to L2 interface and can't accept any L3 related
configuration. l3ipvlan(136) refers to L3 interface and can accept
L3 related configuration.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.12.17.1.2 |
priorityMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.13 |
prioWrrPortTableTable for per port weighted round robin (WRR). SEQUENCE OF PrioWrrPortEntry .1.3.6.1.4.1.21839.2.2.26.1.13.12 |
prioWrrPortEntryEntry for per port weighted round robin (WRR). PrioWrrPortEntry .1.3.6.1.4.1.21839.2.2.26.1.13.12.1 |
prioWrrPortIfIndexThe port interface of the prioWrrPortEntry. The interface
identified by a particular value of this index is the
same interface as identified by the same value of
ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.13.12.1.1 |
prioWrrPortTrafficClassTraffic class for this entry, as defined in
dot1dTrafficClass in the P-BRIDGE-MIB. The actual
maximum depends on the hardware, and is
equal to dot1dPortNumTrafficClasses-1. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.13.12.1.2 |
prioWrrPortWeightWeight for this entry. Value of the object should be
ignored when prioQueueMode is strictAndWrr(3), and
prioWrrPortStrictStatus is enabled(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.13.12.1.3 |
prioWrrPortStrictStatusThis object is used when prioSchedModePort is
strictAndWrr(4).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.13.12.1.4 |
prioSchedModePortTableTable for per port scheduling mode. SEQUENCE OF PrioSchedModePortEntry .1.3.6.1.4.1.21839.2.2.26.1.13.15 |
prioSchedModePortEntryEntry for per port scheduling mode. PrioSchedModePortEntry .1.3.6.1.4.1.21839.2.2.26.1.13.15.1 |
prioSchedModePortIndexThe port interface of the prioSchedModePortEntry. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.13.15.1.1 |
prioSchedModePortThe scheduling mode status of ethernet port.
wrr(1),strict(2), strict-wrr(4)rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.13.15.1.2 |
trapDestMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.14 |
trapVar OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.14.2 |
trapIpFilterRejectModeThis variable is for trap var binding,
indicated the ipfilter reject mode.
web(1),
snmp(2),
telnet(3).ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.14.2.6 |
trapIpFilterRejectIpThis variable is for trap var binding,
indicating the IP address that rejected by the ipfilter.ro IpAddress .1.3.6.1.4.1.21839.2.2.26.1.14.2.7 |
trapVarMacAddrThe MAC address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.14.2.10 |
trapVarLoginUserNameThe name of the user who logs into the switch.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.14.2.11 |
trapVarSessionTypeThe method by which the user logs in to control the
switch.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.14.2.12 |
trapVarLoginInetAddressTypeThe address type of the address associated with this agent.
Only IPv4 and IPv6 types are supported.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.14.2.15 |
trapVarLoginInetAddressThe IP address from which the user logs into the switch.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.14.2.16 |
trapIpFilterRejectInetAddressTypeThis variable is for trap var binding, indicating
the IP address that was rejected by the IP filter.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.14.2.17 |
trapIpFilterRejectInetAddressThis variable is for trap var binding, indicating
the IP address that was rejected by the IP filter.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.14.2.18 |
trapAutoUpgradeResultThe parameter indicates which result triggers the trap.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.14.2.22 |
trapAutoUpgradeNewVerThe parameter indicates new version which was upgraded to.
When trapAutoUpgradeResult was failed(2), it would be
null string.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.14.2.23 |
trapIfIndexThis variable is for trap var binding,
indicating the index of an interface.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.14.2.30 |
trapVlanIdThis variable is for trap var binding,
indicating the identifier of a VLAN.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.14.2.31 |
trapDhcpClientPortIfIndexifIndex for the port connected to DHCP rogue server.ro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.14.2.62 |
trapDhcpServerIpAddressThe IP address of the rogue server.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.14.2.63 |
trapSfpThresholdAlarmWarnIfIndexifIndex for the port issued alarm/warning trap.ro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.14.2.64 |
trapSfpThresholdAlarmWarnTypeSFP's alarm/warning type .ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.14.2.65 |
trapDhcpServerMacAddressThe MAC address of the rogue server.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.14.2.67 |
trapMacNotifyActionThe parameter indicates which result triggers the trap.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.14.2.68 |
qosMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.16 |
rateLimitMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.16.1 |
rateLimitPortTableTable for rate limit of each port. SEQUENCE OF RateLimitPortEntry .1.3.6.1.4.1.21839.2.2.26.1.16.1.2 |
rateLimitPortEntryEntry for rate limit of each port. RateLimitPortEntry .1.3.6.1.4.1.21839.2.2.26.1.16.1.2.1 |
rlPortIndexThe port and the trunk (including trunk member) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by the same
value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.1.2.1.1 |
rlPortInputStatusWhether input rate limit is enabled for this port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.1.2.1.6 |
rlPortOutputStatusWhether output rate limit is enabled for this port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.1.2.1.7 |
rlPortInputLimitInKiloValue of the input rate limit. Its unit is kilobits per
second. For a 100 Mbps port, the range is 64 to 100000.
For a 1000 Mbps port, the range is 64 to 1000000.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.1.2.1.10 |
rlPortOutputLimitInKiloValue of the output rate limit. Its unit is kilobits per
second. For a 100 Mbps port, the range is 64 to 100000.
For a 1000 Mbps port, the range is 64 to 1000000.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.1.2.1.11 |
rlPortLimitInKiloResolutionPresent the rate's resolution. Its unit is kilobits per
secondro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.1.2.1.12 |
cosMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.16.3 |
prioIfClassificationModeTableTable for setting the interface Qos mapping classification mode. SEQUENCE OF PrioIfClassificationModeEntry .1.3.6.1.4.1.21839.2.2.26.1.16.3.2 |
prioIfClassificationModeEntryEntry for setting the interface Qos mapping classification mode. PrioIfClassificationModeEntry .1.3.6.1.4.1.21839.2.2.26.1.16.3.2.1 |
prioIfClassificationModeIfThe port or trunk interface of the device. The interface identified by
a particular value of this index is the same interface as identified
by the same value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.3.2.1.1 |
prioIfClassificationModeStatusThe Qos mapping classification mode of the interface. cos mode means
that the internal priority is mapped from priority field of packet's
VLAN tag if a VLAN tag exists; IP precedence mode means that the
internal priority is mapped from the IP precedence value of IP
packets; DSCP mode means the internal priority is mapped from the dscp
value of IP packets.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.3.2.1.2 |
prioIngressCosToQueueTableTable for cos to queue mapping. SEQUENCE OF PrioIngressCosToQueueEntry .1.3.6.1.4.1.21839.2.2.26.1.16.3.10 |
prioIngressCosToQueueEntryEntry for cos to queue mapping. PrioIngressCosToQueueEntry .1.3.6.1.4.1.21839.2.2.26.1.16.3.10.1 |
prioIngressCosToQueueIfValueThe port or trunk interface of the device. The interface identified by
a particular value of this index is the same interface as identified
by the same value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.3.10.1.1 |
prioIngressCosToQueueCosValueThe cos value on VLAN tag of inject packet. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.3.10.1.2 |
prioIngressCosToQueueCfiValueThe cfi value on VLAN tag of inject packet. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.3.10.1.3 |
prioIngressCosToQueueQueueValueThe queue value which is mapped from the (cos,cfi) value of QoS label.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.3.10.1.4 |
prioIngressDscpToQueueTableTable for dscp to queue mapping. SEQUENCE OF PrioIngressDscpToQueueEntry .1.3.6.1.4.1.21839.2.2.26.1.16.3.11 |
prioIngressDscpToQueueEntryEntry for dscp to queue mapping. PrioIngressDscpToQueueEntry .1.3.6.1.4.1.21839.2.2.26.1.16.3.11.1 |
prioIngressDscpToQueueIfValueThe port or trunk interface of the device. The interface identified by
a particular value of this index is the same interface as identified
by the same value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.3.11.1.1 |
prioIngressDscpToQueueDscpValueThe dscp value on VLAN tag of inject packet. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.3.11.1.2 |
prioIngressDscpToQueueQueueValueThe queue value which is mapped from the dscp value of QoS label.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.3.11.1.3 |
diffServMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.16.4 |
diffServPolicyMapTableTable for policy map. SEQUENCE OF DiffServPolicyMapEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.10 |
diffServPolicyMapEntryEntry for policy map. DiffServPolicyMapEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.10.1 |
diffServPolicyMapIndexAn index that uniquely identifies an entry in this table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.10.1.1 |
diffServPolicyMapNameThe name of this entry.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.16.4.10.1.2 |
diffServPolicyMapDescriptionThe description of this entry.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.16.4.10.1.3 |
diffServPolicyMapElementIndexListThe octet string containes the diffServPolicyMapElementEntry
indexes. Two octets express one index and it is represented
in network order. This index list indicates the
diffServPolicyMapEntrys which belong to this entry.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.10.1.4 |
diffServPolicyMapStatusThis object is used to create a new row, or modify or delete
an existing row, in this table. The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active');it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.10.1.5 |
diffServPolicyMapAttachCtl OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.16.4.11 |
diffServPolicyMapAttachCtlIndexIndex for attachment control.
Specifies the policy map as the target to relate with
the policy map element. The policy map identified by
a particular value of this index is associated with
the same diffServPolicyMapEntry as identified by the
same value of diffServPolicyMapIndex.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.11.1 |
diffServPolicyMapAttachCtlElementIndexElement Index for attachment control.Specifies the policy map
element to relate with the policy map. The policy map element
identified by a particular value of this index is associated
with the same diffServPolicyMapElementEntry as identified by
the same value of diffServPolicyMapElementIndex.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.11.2 |
diffServPolicyMapAttachCtlActionAction for attachment control. When setting this object to
attach(2) to begin the attaching operation, a particular
policy map element is attached to a particular policy map.
When setting this object to detach(3) to begin the not
attached operation, a particular policy map element is not
attached to a particular policy map. When the action is
finshed or no action is taken, the value of this object is
noAction(1). A particular policy map is specified in the
diffServPolicyMapAttachCtlIndex. A particularpolicy map
element is specified in the
diffServPolicyMapAttachCtlElementIndex.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.11.3 |
diffServPolicyMapElementTableTable for policy map element. SEQUENCE OF DiffServPolicyMapElementEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.12 |
diffServPolicyMapElementEntryEntry for policy map element. DiffServPolicyMapElementEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.12.1 |
diffServPolicyMapElementIndexAn index that uniquely identifies an entry in this table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.12.1.1 |
diffServPolicyMapElementClassMapIndexSpecifies the class map binding to this entry. The class map
identified by a particular value of this index is associated
with the same diffServClassMapEntry as identified by the same
value of diffServClassMapIndex.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.12.1.2 |
diffServPolicyMapElementMeterIndexSpecifies the meter binding to this entry. The meter
identified by a particular value of this index is associated
with the same diffServMeterEntry as identified by the same
value of diffServMeterIndex. If this value is
zero, no associated meter will be associated, as zero is not a
valid meter index.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.12.1.3 |
diffServPolicyMapElementActionIndexSpecifies the action binding to this entry. The action
identified by a particular value of this index is associated
with the same diffServActionEntry as identified by the same
value of diffServActionIndex.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.12.1.4 |
diffServPolicyMapElementStatusThis object is used to create a new row, or modify or delete
an existing row, in this table. The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active'); it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.12.1.5 |
diffServClassMapTableTable for class map. SEQUENCE OF DiffServClassMapEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.13 |
diffServClassMapEntryEntry for class map. DiffServClassMapEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1 |
diffServClassMapIndexAn index that uniquely identifies an entry in this table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1.1 |
diffServClassMapNameThe name of this entry.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1.2 |
diffServClassMapDescriptionThe description of this entry.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1.3 |
diffServClassMapMatchTypeThe map match type of this entry.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1.4 |
diffServClassMapElementIndexTypeListThe octet string containes the type of class map element
indexes. Two octets which are represented in network order
express one type of the class map element index in network
order and it maps the index of
differServClasssMapElementIndexList in order. When the type is
macAce(1), the maping index of
differServClasssMapElementIndexList is the
diffServMacAceEntry. When the type is ipAce(2), the maping
index of differServClasssMapElementIndexList is the
diffServIpAceEntry. When the type is acl(3), the maping index
of differServClasssMapElementIndexList is the diffServAclEntry.
When the type is ipv6Ace(4), the maping index of
differServClasssMapElementIndexList is the diffServIpv6AceEntry.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1.5 |
diffServClassMapElementIndexListThe octet string containes the class map element indexes. Two
octets express one index and it is represented in
network order. This index list indicates the particular
class map elements which belong to this table. The class map
element uses type to indicate diffServAclEntry, the
diffServIpAceEntry or diffServMacAceEntry. The type is two
octet specified in differServClasssMapElementIndexTypeList
in order. When the type is macAce(1), the maping index of
differServClasssMapElementIndexList is the
diffServMacAceEntry. When the type is ipAce(2), the maping
index of differServClasssMapElementIndexList is the
diffServIpAceEntry. When the type is acl(3), the maping index
of differServClasssMapElementIndexList is the diffServAclEntry.
When type is ipv6Ace(4), the maping index of
differServClasssMapElementIndexList is the
diffServIpv6AceEntry.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1.6 |
diffServClassMapStatusThis object is used to create a new row or modify or delete
an existing row in this table.The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active'); it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.13.1.7 |
diffServClassMapAttachCtl OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.16.4.14 |
diffServClassMapAttachCtlIndexIndex for attachment control. Specifies the class map as
the target to relate with class map elements. The class
map identified by a particular value of this index is
associated with the same diffServClassMapEntry as
identified by the same value of diffServClassMapIndex.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.14.1 |
diffServClassMapAttachCtlElementIndexTypeElement Index for attachment control. Specifies the type of
class map element to relate with the class map. When type is
macAce(1), the index of diffServClassMapAttachCtlElementIndex
is the index of diffServMacAceEntry. When the type is
ipAce(2), the index of diffServClassMapAttachCtlElementIndex
is the index of diffServIpAceEntry. When the type is acl(3),
the index of diffServClassMapAttachCtlElementIndex is the
index of diffServAclEntry. When type is ipv6Ace(4), the index of
diffServClassMapAttachCtlElementIndex is the index of
diffServIpv6AceEntry.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.14.2 |
diffServClassMapAttachCtlElementIndexElement Index for attachment control. Specifies the class map
element related with the class map. The class map element uses
type to indicate diffServAclEntry, the diffServIpAceEntry or
diffServMacAceEntry. The type is specified in
diffServClassMapAttachCtlElementIndexType. When
the type is macAce(1), the maping index of
differServClasssMapElementIndexList is the
diffServMacAceEntry. When the type is ipAce(2), the maping
index of differServClasssMapElementIndexList is the
diffServIpAceEntry. When the type is acl(3), the maping index
of differServClasssMapElementIndexList is the
diffServAclEntry. When type is ipv6Ace(4), the maping index of
differServClasssMapElementIndexList is the diffServIpv6AceEntry.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.14.3 |
diffServClassMapAttachCtlActionAction for attachment control. When setting this object to
attach(2) to begin the attaching operation, a particular class
map element is attached to a particular class map. When
setting this object to detach(3) to begin the not attached
operation, then a particular class map element is not attached
to a particular class map. When the action is finshed whether
successfully or not, or no action is taken, the value of this
object always is noAction(1). The value of a particular class
map is specified in the AclAttachCtlTargetIndex. The class map
element is specified by diffServClassMapAttachCtlElementIndexType
and diffServClassMapAttachCtlElementIndex.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.14.4 |
diffServAclTableTable for ACL. SEQUENCE OF DiffServAclEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.15 |
diffServAclEntryEntry for ACL. DiffServAclEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.15.1 |
diffServAclIndexAn index that uniquely identifies an entry in the ACL
table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.15.1.1 |
diffServAclNameThe name of this entry.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.16.4.15.1.2 |
diffServAclTypeThe type of this entry. When the value of ACL type is
modified, then the ACEs in the diffServAclAceIndexList of
this entry will be auto-removed, and this entry will be auto-
unbound from the diffServPortTable and the
diffServClassMapTable.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.15.1.3 |
diffServAclAceIndexListThe octet string containes the ACE indexes. Two octets
express one index and it is represented in network
order. This index list indicates the particular ACEs which
belong to this table. The ACE uses type to indicate the
diffServMacAceEntry, the diffServIpAceEntry, the
diffServIpv6AceEntry or the diffServArpAceEntry. The type is
specified in diffServAclType. When the type is mac(1), the
index of diffServAclAceIndexList is the diffServMacAceEntry.
When the type is ipstandard(2) or ipextended(3), the index of
diffServAclAceIndexList is the diffServIpAceEntry. When the
type is ipv6standard(4) or ipv6extended(5), the index of
diffServAclAceIndexList is the diffServIpv6AceEntry. When the
type is arp(6), the index of diffServAclAceIndexList is the
diffServArpAceEntry.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.15.1.4 |
diffServAclStatusThis object is used to create a new row or modify or delete
an existing row in this table. The status column has six
defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active'); it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.15.1.5 |
diffServAclAttachCtl OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.16.4.16 |
diffServAclAttachCtlIndexIndex for attachment control. Specifies the ACL as the
target to relate with the IP ACE, the MAC ACE or IPv6 ACE.
The ACL identified by a particular value of this index is
associated with the same diffServAclEntry as identified by
the same value of diffServAclIndex.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.16.1 |
diffServAclAttachCtlAceTypeType for attachment control. Specifies the type of
diffServAclAttachCtlAceIndex to relate with the
diffServAclAttachCtlIndex. When the type is macAce(1), the
index of diffServAclAceIndexList is the diffServMacAceEntry.
When the type is ipAce(2), the index of
diffServAclAceIndexList is the diffServIpAceEntry. When the
type is ipv6Ace(3), the index of diffServAclAceIndexList
is the diffServIpv6AceEntry. When the type is arpAce(4), the
index of diffServAclAceIndexList is the diffServArpAceEntry.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.16.2 |
diffServAclAttachCtlAceIndexIndex for attachment control. Specifies the ACE to relate with
the diffServAclAttachCtlIndex. When
diffServAclAttachCtlAceType is macAce(1), the value of
diffServAclAttachCtlIndex is the diffServMacAceEntry. When
diffServAclAttachCtlAceType is ipAce(2), the value of
diffServAclAttachCtlIndex is the diffServIpAceEntry. When
diffServAclAttachCtlAceType is ipv6Ace(3), the value of
diffServAclAttachCtlIndex is the diffServIpv6AceEntry. When
diffServAclAttachCtlAceType is arpAce(4), the value of
diffServAclAttachCtlIndex is the diffServArpAceEntry.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.16.3 |
diffServAclAttachCtlActionAction for attachment control. When setting this object to
attach(2) to begin the attaching operation, a particular ACE
is attached to a particular ACL. When setting this object to
detach(3) to begin the not attached operation, then a
particular ACE is not attached to a particular ACL. When the
action is finshed whether successfully or not, or no action
is taken, the value of this object always is noAction(1), The
value of a particular ACL is specified in the
diffServAclAttachCtlAceType and diffServAclAttachCtlAceIndex.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.16.4 |
diffServIpAceTableTable for IP ACE. SEQUENCE OF DiffServIpAceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.17 |
diffServIpAceEntryEntry for IP ACE. DiffServIpAceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1 |
diffServIpAceIndexAn index that uniquely identifies an entry in the IP ACE
table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.1 |
diffServIpAceTypeThe specified IP ACE type. When the type of this entry is
modified, then this entry will be auto-unbound from the
diffServAclEntry and the not supporting field of this entry
will be set 0.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.2 |
diffServIpAceAccessIndicates the action to be taken if a packet matches this
ACE.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.3 |
diffServIpAceSourceIpAddrThe specified source IP address. The packet's source address
is AND-ed with the value of IpAceSourceIpAddrBitmask and then
compared against the value of this object.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.4 |
diffServIpAceSourceIpAddrBitmaskThe specified source IP address mask. The packet's source
address is AND-ed with the value of IpAceSourceIpAddr and
then compared against the value of this object.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.5 |
diffServIpAceDestIpAddrThe specified destination IP address. The packet's
destination address is AND-ed with the value of
diffServIpAceDestIpAddrBitmask and then compared against the
value of this object. This object may not be modified if the
associated diffServIpAceType object is equal to standard(1).rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.6 |
diffServIpAceDestIpAddrBitmaskThe specified destination IP address mask. This object may
not be modified if the associated diffServIpAceType object
is equal to standard(1).rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.7 |
diffServIpAceProtocolThe protocol number field in the IP header used to indicate
the higher layer protocol as specified in RFC 1700. A value
of 0 matches every IP packet. The object=256 means 'any'. For
example: 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP
encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50
is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS
compatible IP over IP, 103 is PIMv2, 108 is PCP. This object
may not be modified if the associated diffServIpAceType object
is equal to standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.8 |
diffServIpAcePrecSpecifies the IP precedence value to match against. The value
of this object is ignored whenever the value of
diffServIpAcePrec object is 8. This object may not be modified
if the associated diffServIpAceType object is equal to
standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.9 |
diffServIpAceDscpSpecifies the DSCP value to match against. The value of this
object is ignored whenever the value of diffServIpAcePrec
object is 64. This object may not be modified if the
associated diffServIpAceType object is equal to standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.11 |
diffServIpAceSourcePortOpIndicates how a packet's source TCP/UDP port number is to be
compared. noOperator(1), which is the default value, means no
comparison is to be made with the source TCP/UDP port
number. equal(2), which is used the
diffServIpAceSourcePortBitmask and the
diffServIpAceMinSourcePort to match against. range(3),which is
used the diffServIpAceMinSourcePort and the
diffServIpAceMaxSourcePort to match against. This object may
not be modified if the associated diffServIpAceType object is
equal to standard(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.12 |
diffServIpAceMinSourcePortIf the diffServIpAceSourcePortOp is range(3), this
indicates the lower bound of the TCP/UDP port number
value range. This object may not be modified if the
associated diffServIpAceType object is equal to
standard(1).rw Integer32 (0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.13 |
diffServIpAceSourcePortBitmaskIf the diffServIpAceSourcePortOp is equal(2), this indicates
the bitmask of the diffServIpAceMinSourcePort. This object may
not be modified if the associated diffServIpAceType object is
equal to standard(1).rw Integer32 (0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.15 |
diffServIpAceDestPortOpIndicates how a packet's destination TCP/UDP port number is
to be compared. noOperator(1), which is the default value,
means that no comparison is to be made with the destination
TCP/UDP port number. equal(2), which is used the
diffServIpAceSourcePortBitmask and the
diffServIpAceMinDestPort to match against. range(3),which is
used the diffServIpAceMinDestPort and the
diffServIpAceMaxDestPort to match against. This object may not
be modified if the associated diffServIpAceType object is
equal to standard(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.16 |
diffServIpAceMinDestPortIf the diffServIpAceDestPortOp is range(3), this indicates
the lower bound of the TCP/UDP port number value range. This
object may not be modified if the associated
diffServIpAceType object is equal to standard(1).rw Integer32 (0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.17 |
diffServIpAceDestPortBitmaskIf the diffServIpAceDestPortOp is equal(2), this indicates
the bitmask of the diffServIpAceMinDestPort. This object may
not be modified if the associated diffServIpAceType object
is equal to standard(1).rw Integer32 (0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.19 |
diffServIpAceControlCodeIndicates how the control flags of TCP packets are to be
compared. diffServIpAceControlCode is AND-ed with
diffServIpAceControlCodeBitmask. This object may not be
modified if the associated diffServIpAceType object is
equal to standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.20 |
diffServIpAceControlCodeBitmaskIndicates how the control flags of TCP packets are to be
compared. It can be used to check multiple flags of the FIN,
SYN, RST, PSH, ACK, URG by the sum of FIN=1, SYN=2, RST=4,
PSH=8, ACK=16, URG=32. This object may not be modified if the
associated diffServIpAceType object is equal to standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.21 |
diffServIpAceStatusThis object is used to create a new row or modify or delete
an existing row in this table. The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active'); it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.17.1.22 |
diffServMacAceTableTable for MAC ACE. SEQUENCE OF DiffServMacAceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.18 |
diffServMacAceEntryEntry for MAC ACE. DiffServMacAceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1 |
diffServMacAceIndexAn index that uniquely identifies an entry in the MAC ACE
table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.1 |
diffServMacAceAccessIndicates the action to be taken if a packet matches this
ACE.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.2 |
diffServMacAcePktformatUsed to check the packet format of the packets. This object
cannot be configured when the status of the entry,
diffServMacAceStatus, is active(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.3 |
diffServMacAceSourceMacAddrIndicates the 48-bit source MAC address. The specified source
MAC of the packet. The packet's source MAC address is AND-ed
with the value of diffServMacAceSourceMacAddrBitmask
and then compared against the value of this object.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.4 |
diffServMacAceSourceMacAddrBitmaskThe specified source MAC address mask.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.5 |
diffServMacAceDestMacAddrIndicates the 48-bit destination MAC address. The specified
destination MAC of the packet. The packet's destination MAC
address is AND-ed with the value of
diffServMacAceDestMacAddrBitmask and then compared against
the value of this object.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.6 |
diffServMacAceDestMacAddrBitmaskThe specified destination MAC address mask.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.7 |
diffServMacAceVidOpIndicates how a packet's VID is to be compared. This
object cannot be configured when the status of the entry,
diffServMacAceStatus, is active(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.8 |
diffServMacAceMinVidIndicates the lower bound of the VID value range if the
diffServMacAceVidOp is range(3).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.9 |
diffServMacAceVidBitmaskThe bit mask of the VID. The default value is 0.rw Integer32 (0..'0FFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.10 |
diffServMacAceEtherTypeOpIndicates how a packet's ether type is to be compared.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.12 |
diffServMacAceEtherTypeBitmaskThe bit mask of Ether type. The default value is 0.rw Integer32 (0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.13 |
diffServMacAceMinEtherTypeIndicates the lower bound of the ether type value range
if the diffServMacAceEtherTypeOp is range(3).rw Integer32 ('0000'h..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.14 |
diffServMacAceStatusThis object is used to create a new row or modify or delete
an existing row in this table. The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active'); it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.16 |
diffServMacAceCosOpIndicates how a packet's CoS is compared.
If the object type of diffServMacAceCosOp is equal(2),
diffServMacAceMinCos indicates the CoS value for comparing, and
diffServMacAceCosBitmask is used as the bitmask of the CoS value.
If the object type of diffServMacAceCosOp is range(3),
diffServMacAceMinCos should be used as the lower bound of the CoS value.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.17 |
diffServMacAceCosBitmaskIndicates the bitmask of the CoS value if the object type of
diffServMacAceCosOp is equal(2). The default value is 0.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.18 |
diffServMacAceMinCosIf the object type of diffServMacAceCosOp is equal(2),
diffServMacAceMinCos indicates the CoS value for comparing.
If the object type of diffServMacAceCosOp is range(3),
diffServMacAceMinCos indicates the lower bound of the CoS value.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.18.1.19 |
diffServActionTableTable for action. SEQUENCE OF DiffServActionEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.19 |
diffServActionEntryEntry for action. DiffServActionEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.19.1 |
diffServActionIndexAn index that uniquely identifies an entry in the
action table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.19.1.1 |
diffServActionListThe bitmap value used to identify which action
capabilities are enabled on the entry. The
actionPktNewPri and actionPktNewDscp can not be
enabled at the same time on the entry. The
actionRedPktNewDscp and actionRedDrop can not be
enabled at the same time on the entry.rw Bits .1.3.6.1.4.1.21839.2.2.26.1.16.4.19.1.2 |
diffServActionPktNewPriSpecifies the new priority value for the packet when
the action is satisfied. If the actionPktNewPri bit of
the diffServActionList is not enabled, this object can
not be set.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.19.1.3 |
diffServActionStatusThis object is used to create a new row, modify or
delete an existing row in this table.
The status column has six defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row
is available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use
by the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically
set to active, making it available for use by the
managed device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management
station wishing to delete all of the instances
associated with an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService'
or 'active'. That is, when queried, an existing
conceptual row has only three states: it is either
available for use by the managed device (the status column
has the value 'active'); it is not available for use by
the managed device, though the agent has sufficient
information to make it so (the status column has the value
'notInService'); or, it is not available for use by the
managed device, and an attempt to make it so would fail
because the agent has insufficient information (the state
column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.19.1.11 |
diffServActionPktNewDscpSpecifies the new DSCP value for the packet when
the action is satisfied. If the actionPktNewDscp bit of
the diffServActionList is not enabled, this object
can not be set.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.19.1.13 |
diffServMeterTableTable for meter. SEQUENCE OF DiffServMeterEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.20 |
diffServMeterEntryEntry for meter. DiffServMeterEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.20.1 |
diffServMeterIndexAn entry that describes a single set of token bucket
parameters. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.20.1.1 |
diffServMeterModelThe Metering algorithm associated with the Token Bucket
parameters. The zeroDotZero indicates this is unknown.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.20.1.2 |
diffServMeterRateThe token-bucket rate, in kilobits per second (kbps).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.20.1.3 |
diffServMeterStatusThis object is used to create a new row or modify or delete
an existing row in this table. The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active'); it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.20.1.6 |
diffServIpv6AceTableTable for IPv6 ACE. SEQUENCE OF DiffServIpv6AceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.21 |
diffServIpv6AceEntryEntry fo IPv6 ACE. DiffServIpv6AceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1 |
diffServIpv6AceIndexAn index that uniquely identifies an entry in the IPv6 table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.1 |
diffServIpv6AceTypeThe specified IP v6 ACE type. When the type of this entry is
modified, then this entry will be auto-unbound from the
diffServAclEntry and the not supporting field of this entry
will be set 0.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.2 |
diffServIpv6AceAccessIndicates the action to be taken if a packet matches this
ACE.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.3 |
diffServIpv6AceSourceIpAddrSpecifies the source IPv6 address.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.4 |
diffServIpv6AceSourceIpAddrPrefixLenThe length (in bits) associated with the source IPv6 address
prefix of this entry.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.5 |
diffServIpv6AceDestIpAddrSpecifies the destination IPv6 address. This object may not be
modified if the associated diffServIpv6AceType object is equal
to standard(1).rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.6 |
diffServIpv6AceDestIpAddrPrefixLenThe length (in bits) associated with the destination IPv6
address prefix of this entry. This object may not be modified
if the associated diffServIpv6AceType object is equal to
standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.7 |
diffServIpv6AceNextHeaderSpecifies the next header to match against. This object may not
be modified if the associated diffServIpv6AceType object is equal to
standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.8 |
diffServIpv6AceDscpSpecifies the DSCP value to match against. This object may not
be modified if the associated diffServIpv6AceType object is
equal to standard(1).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.9 |
diffServIpv6AceStatusThis object is used to create a new row or modify or delete
an existing row in this table. The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has the value
'active'); it is not available for use by the managed device,
though the agent has sufficient information to make it so
(the status column has the value 'notInService'); or, it is
not available for use by the managed device, and an attempt
to make it so would fail because the agent has insufficient
information (the state column has the value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.11 |
diffServIpv6AceSourcePortOpIndicates how a packet's source TCP/UDP port number is
to be compared. noOperator(1), which is the default value,
means that no comparison is to be made with the source
TCP/UDP port number. equal(2), which uses the
diffServIpv6AceSourcePort and diffServIpv6AceSourcePortBitmask
to match against. This object may not be modified if the
associated diffServIpv6AceType object is equal to standard(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.13 |
diffServIpv6AceSourcePortIf the diffServIpv6AceSourcePortOp is equal(2), this
indicates the TCP/UDP port number value. Integer32(0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.14 |
diffServIpv6AceSourcePortBitmaskIf the diffServIpv6AceSourcePortOp is equal(2), this indicates
the bitmask of the diffServIpv6AceSourcePort.rw Integer32(0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.15 |
diffServIpv6AceDestPortOpIndicates how a packet's destination TCP/UDP port number is
to be compared. noOperator(1), which is the default value,
means that no comparison is to be made with the destination
TCP/UDP port number. equal(2), which uses the
diffServIpv6AceDestPort and diffServIpv6AceDestPortBitmask to
match against. This object may not be modified if the
associated diffServIpv6AceType object is equal to standard(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.16 |
diffServIpv6AceDestPortIf the diffServIpv6AceDestPortOp is equal(2), this
indicates the TCP/UDP port number value.rw Integer32(0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.17 |
diffServIpv6AceDestPortBitmaskIf the diffServIpv6AceDestPortOp is equal(2), this indicates
the bitmask of the diffServIpv6AceDestPort.rw Integer32(0..'FFFF'h) .1.3.6.1.4.1.21839.2.2.26.1.16.4.21.1.18 |
diffServArpAceTableThe conceptual table of all of diffServArpAceEntry. SEQUENCE OF DiffServArpAceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.23 |
diffServArpAceEntryThe conceptual row for diffServArpAceTable. DiffServArpAceEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1 |
diffServArpAceIndexThe unique index of an ACE within an ACL. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.1 |
diffServArpAceActionIndicates the action to be taken if a packet matches
this ACE. This object cannot not be configured when
the status of the entry, diffServArpAceStatus, is
active(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.2 |
diffServArpAcePktTypeIndicates the packet type to be taken if a packet matches
this ACE. This object can not be configured when the
status of the entry, diffServArpAceStatus, is active(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.3 |
diffServArpAceSourceIpAddrThe specified source ARP address. The packet's source
address is AND'ed with the value of
diffServArpAceSourceIpAddrBitmask and then compared
against the value of this object.
This object cannot be configured when the status of the
entry, diffServArpAceStatus, is active(1).rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.4 |
diffServArpAceSourceIpAddrBitmaskThe specified source ARP address mask. The packet's
destination address is AND'ed with the value of
diffServArpAceSourceIpAddr and then compared against the
value of this object.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.5 |
diffServArpAceDestIpAddrThe specified destination IP address. The packet's
destination address is AND'ed with the value of
diffServArpAceDestIpAddrBitmask and then compared
against the value of this object.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.6 |
diffServArpAceDestIpAddrBitmaskThe specified destination IP address mask.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.7 |
diffServArpAceSourceMacAddrIndicates the 48-bit destination MAC address. The
specified source MAC of the packet. The packet's
source MAC address is AND'ed with the value of
aceArpSourceMacAddrBitmask and then compared against
the value of this object. This object cannot be
configured when the status of the entry,
diffServArpAceStatus, is active(1).rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.8 |
diffServArpAceSourceMacAddrBitmaskThe specified source MAC address mask.
This object cannot be configured when the status of the
entry, diffServArpAceStatus, is active(1).rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.9 |
diffServArpAceDestMacAddrIndicates the 48-bit destination MAC address.
The specified destination MAC of the packet.
The packet's destination MAC address is AND'ed with the
value of aceArpDestMacAddrBitmask and then compared
against the value of this object. This object cannot be
configured when the status of the entry,
diffServArpAceStatus, is active(1).rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.10 |
diffServArpAceDestMacAddrBitmaskThe specified destination MAC address mask.
This object cannot be configured when the status of the
entry, diffServArpAceStatus, is active(1).rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.11 |
diffServArpAceLogStatusIndicates whether to log messages against the packets.
This object cannot be configured when the status of the
entry, diffServArpAceStatus, is active(1).rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.12 |
diffServArpAceStatusThe status of this conceptual row entry. This object isused to manage the
creation and deletion of conceptual rows.
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has value 'active');
it is not available for use by the managed device, though
the agent has sufficient information to make it so (the
status column has value 'notInService'); or, it is not
available for use by the managed device, and an attempt to
make it so would fail because the agent has insufficient
information (the state column has value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.23.1.13 |
diffServArpTableThe conceptual table of all of diffServArpEntry. SEQUENCE OF DiffServArpEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.24 |
diffServArpEntryThe conceptual row for diffServArpTable. DiffServArpEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.24.1 |
diffServArpAclNameThe name of an ACL. Within a feature, a unique name is
used to identify the list to which the entry belongs
in the device.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.16.4.24.1.1 |
diffServAclHwCounterTableTable for differentiated services hardware counter on
each port. SEQUENCE OF DiffServAclHwCounterEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.26 |
diffServAclHwCounterEntryEntry for differentiated services hardware counter on
each port. DiffServAclHwCounterEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.26.1 |
diffServAclHwCounterIfIndexThis object is the interface index of diffServPortEntry.
The interface identified by a particular value of this
index is the same interface as identified by the same
value of ifIndex in the IF-MIB.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.4.26.1.1 |
diffServAclHwCounterDirectionIndicates a particular direction of traffic.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.26.1.2 |
diffServAclHwCounterAclIndexAn index that uniquely identifies an entry in the ACL
table.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.26.1.3 |
diffServAclHwCounterAceIndexAn index that uniquely identifies an entry of an ACL.
This entry might be a compressed ACE (which index is
bigger than SYS_ADPT_MAX_NBRS_OF_ACE_OF_SYSTEM) with
multiple user configured ACEs, and the index of
compressed ACE will not show in ACE table.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.26.1.4 |
diffServAclHwCounterAceHitCountSpecifies the hardware counter of an ACE entry.ro Unsigned32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.26.1.5 |
diffServPolicyMapPortTableTable for policy map of each port. SEQUENCE OF DiffServPolicyMapPortEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.27 |
diffServPolicyMapPortEntryEntry for diffServPolicyMapPortTable. DiffServPolicyMapPortEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.27.1 |
diffServPolicyMapPortIfIndexThis object is the interface index of DiffServPolicyMapPortEntry.
The interface identified by a particular value of this
index is the same interface as identified by the same
value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.4.27.1.1 |
diffServPolicyMapPortDirectionIndicates this policy map effect to
which direction of traffic. Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.27.1.2 |
diffServPolicyMapPortPolicyMapIndexSpecifies the policy map index binded to the interface.
The policy map identified by a particular value of
this index is associated with the same DiffServPolicyMapEntry
as identified by the same value of diffServPolicyMapIndex.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.27.1.3 |
diffServPolicyMapPortStatusThis object is used to create a new row or modify or delete
an existing row in this table.The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has value 'active');
it is not available for use by the managed device, though
the agent has sufficient information to make it so (the
status column has value 'notInService'); or, it is not
available for use by the managed device, and an attempt to
make it so would fail because the agent has insufficient
information (the state column has value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.27.1.4 |
diffServAccessGroupTableTable for specifies access group
for ACL on each port. SEQUENCE OF DiffServAccessGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.28 |
diffServAccessGroupEntryEntry for diffServAccessGroupTable. DiffServAccessGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1 |
diffServAccessGroupIfIndexThis object is the interface index of diffServAccessGroupEntry.
The interface identified by a particular value of this
index is the same interface as identified by the same
value of ifIndex in the IF-MIB. If support global ACL,
using the specific ifindex(65535). InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1.1 |
diffServAccessGroupDirectionIndicates this access group effect to
which direction of traffic. Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1.2 |
diffServAccessGroupTypeSpecifies the access group type,
only support bind one ACL per type on a port. Enumeration .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1.3 |
diffServAccessGroupAclIndexSpecifies the ACL index apply to this access
group. The index uniquely identifies an
entry in diffServAclTable.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1.4 |
diffServAccessGroupTimeRangeNameThe name of the time range entry bound to
the access group. This object should be
equal to one of the timeRangeName objects
in timeRangeTable.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1.5 |
diffServAccessGroupCounterStatusThe acl counter enable status of this
access group.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1.6 |
diffServAccessGroupStatusThis object is used to create a new row or modify or delete
an existing row in this table.The status column has six
defined values:
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
Whereas five of the six values (all except 'notReady') may
be specified in a management protocol set operation, only
three values will be returned in response to a management
protocol retrieval operation: 'notReady', 'notInService' or
'active'. That is, when queried, an existing conceptual row
has only three states: it is either available for use by
the managed device (the status column has value 'active');
it is not available for use by the managed device, though
the agent has sufficient information to make it so (the
status column has value 'notInService'); or, it is not
available for use by the managed device, and an attempt to
make it so would fail because the agent has insufficient
information (the state column has value 'notReady').
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.16.4.28.1.7 |
diffServTcamTableThe conceptual table of all of DiffServTcamEntry. SEQUENCE OF DiffServTcamEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.29 |
diffServTcamEntryThe conceptual row for diffServTcamTable. DiffServTcamEntry .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1 |
diffServTcamUnitThis object identifies the switch within the system
for which this entry contains information. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1.1 |
diffServTcamDeviceThe device id of the specified unit. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1.2 |
diffServTcamPoolThe TCAM pool index of the specified unit and device. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1.3 |
diffServTcamPoolCapabilityThe bitmap value used to identify which functions
supported on this pool.ro Bits .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1.4 |
diffServTcamTotalThe total number of TCAM pool entry.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1.5 |
diffServTcamFreeThe free number of TCAM pool entry.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1.6 |
diffServTcamUsedThe used number of TCAM pool entry.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.16.4.29.1.7 |
securityMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17 |
privateVlanMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.1 |
privateVlanStatusThis controls whether private VLAN is enabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.1.1 |
privateVlanSessionTableContains the settings for private VLAN Session. SEQUENCE OF PrivateVlanSessionEntry .1.3.6.1.4.1.21839.2.2.26.1.17.1.8 |
privateVlanSessionEntryA conceptual row in the privateVlanSession table. PrivateVlanSessionEntry .1.3.6.1.4.1.21839.2.2.26.1.17.1.8.1 |
privateVlanSessionIdThe session ID that may specifiy certain entry in the table which contains private
VLAN session information. INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.1.8.1.1 |
privateVlanSessionUplinkPortsThis is the list of uplink ports for a session of private VLAN. They should not
overlap with the privateVlanSessionPortDownlink of the same session, and they
also should not overlap with the privateVlanSessionPortUplink and the
privateVlanSessionPortDownlink of other session.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.1.8.1.2 |
privateVlanSessionDownlinkPortsThis is the list of downlink ports for a session of private VLAN. They should not
overlap with the privateVlanSessionPortUplink of the same session, and they also
should not overlap with the privateVlanSessionPortUplink and the
privateVlanSessionPortDownlink of other session.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.1.8.1.3 |
privateVlanSessionStatusSet this to valid(1) to create an entry. Sets this to
invalid(2) to destroy an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.1.8.1.4 |
privateVlanUplinkToUplinkSets this to blocking(2) to deny the traffic of uplink
ports between different sessions. Set this to forwarding(1)
to allow the traffic of uplink ports between different
sessions.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.1.9 |
portSecurityMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.2 |
portSecPortTableThe port security(MAC binding) Table. SEQUENCE OF PortSecPortEntry .1.3.6.1.4.1.21839.2.2.26.1.17.2.1 |
portSecPortEntryThe entry of portSecPortTable. PortSecPortEntry .1.3.6.1.4.1.21839.2.2.26.1.17.2.1.1 |
portSecPortIndexThe port and the trunk (excluding trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by the same
value of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.2.1.1.1 |
portSecPortStatusSet enabled(1) to enable port security and set disabled(2) to
disable port security.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.2.1.1.2 |
portSecActionThe corresponding actions that will take place when a
port is under intrusion, when this variable is set to
none(1), no action will be performed, when this variable is
set to trap(2), a swPortSecurityTrap trap will be sent,
when this variable is set to shutdown(3), the port will
shutdown, when this variable is set to
trapAndShutdown(4), a swPortSecurityTrap will be sent
and the port will shutdown.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.2.1.1.3 |
portSecMaxMacCountThe maximun number of MAC addresses that will be learned and locked.
When we change the value of this variable, if the
portSecPortStatus is enabled, we will discard all secure MAC
and begin to learn again, until the number of MAC has reached
this value, and only the secure MAC addresses can enter
this port. If the portSecPortStatus is disabled, we will begin
to learn the MAC, and auto enabled the portSecPortStatus when
the MAC has reached this value.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.2.1.1.4 |
portSecMacAsPermanentMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.2.6 |
portSecMacAsPermanentPortIndexThe port and the trunk (excluding trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by the same
value of ifIndex in the IF-MIB. Specifies the interface to
convert the learnt secured MAC address into manual configured.
'0' represents that no interface is specified.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.2.6.1 |
portSecMacAsPermanentActionSet action(2) to convert the learnt secured MAC address into
manual configured. When action finsh or no action, the value
of this object is noAction(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.2.6.2 |
radiusMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.4 |
radiusServerGlobalAuthPortAauthentication port number for RADIUS server.
When specified radius server do not set
aauthentication port number, this value is used.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.4.1 |
radiusServerGlobalAcctPortAccounting port number of RADIUS server.
When specified radius server do not set
accounting port number, this value is used.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.4.2 |
radiusServerGlobalKeyKey for RADIUS. This variable can only be written.
When this variable is read, it always returns a
zero-length string.
When specified radius server do not set
key, this this value is used.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.4.3 |
radiusServerGlobalRetransmitMaximum number of retransmissions for RADIUS.
When specified radius server do not set
maximum number of retransmissions, this value is used.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.4.4 |
radiusServerGlobalTimeoutTimeout for RADIUS.
When specified radius server do not set
timeout, this value is used.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.4.5 |
radiusServerTableThe table for RADIUS server. SEQUENCE OF RadiusServerEntry .1.3.6.1.4.1.21839.2.2.26.1.17.4.7 |
radiusServerEntryThe conceptual row for radiusServerTable. RadiusServerEntry .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1 |
radiusServerIndexThe RADIUS server index in the table. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.1 |
radiusServerAddressIP address of a RADIUS server.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.2 |
radiusServerAuthPortNumberAuthentication port number of RADIUS server.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.3 |
radiusServerAcctPortNumberAccounting port number of RADIUS server.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.4 |
radiusServerKeyKey for RADIUS. This variable can only be written.
When this variable is read, it always returns a
zero-length string.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.5 |
radiusServerRetransmitTimeout for RADIUS.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.6 |
radiusServerTimeoutTimeout for RADIUS.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.7 |
radiusServerStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.4.7.1.8 |
tacacsMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.5 |
tacacsPlusServerGlobalPortNumberTCP port number of TACACS+ server.
When specified TACACS+ server do not set
TCP port number, this this value is used.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.5.2 |
tacacsPlusServerGlobalKeyThe encryption key used to encrpt the traffic between client and
TACACS+ server. Do not use blank spaces in the string. This variable
can only be set. When this variable is read, it always returns a
zero-length string.When specified TACACS+ server do not set
the encryption key , this this value is used.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.5.3 |
tacacsPlusServerTableThe table for TACACS+ server. SEQUENCE OF TacacsPlusServerEntry .1.3.6.1.4.1.21839.2.2.26.1.17.5.4 |
tacacsPlusServerEntryThe conceptual row for tacacsPlusServerTable. TacacsPlusServerEntry .1.3.6.1.4.1.21839.2.2.26.1.17.5.4.1 |
tacacsPlusServerIndexTACACS+ server index. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.5.4.1.1 |
tacacsPlusServerAddressIP address of a TACACS+ server.rw IpAddress .1.3.6.1.4.1.21839.2.2.26.1.17.5.4.1.2 |
tacacsPlusServerPortNumberTCP port number of a TACACS+ server.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.5.4.1.3 |
tacacsPlusServerKeyThe encryption key used to encrpt the traffic between client and
TACACS+ server. Do not use blank spaces in the string. This
variable can only be set. When this variable is read, it always
returns a zero-length string.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.5.4.1.4 |
tacacsPlusServerStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.5.4.1.8 |
sshMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.6 |
sshServerStatusThe status of Secure Shell Server. Set this value to
enabled(1) to enable SSH server, set this value to
disabled(2) to disable the SSH server.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.6.1 |
sshServerMajorVersionThe major version of the SSH Server.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.6.2 |
sshServerMinorVersionThe minor version of the SSH Server.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.6.3 |
sshTimeoutThe time interval that the router waits for the SSH
client to respond. The range is 1-120.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.6.4 |
sshAuthRetriesThe number of attempts after which the interface is reset.
The range is 1-5.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.6.5 |
sshConnInfoTableThe table for Secure Shell Connection. SEQUENCE OF SshConnInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.17.6.6 |
sshConnInfoEntryThe conceptual row for sshConnInfoTable. SshConnInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1 |
sshConnIDThe connection ID of the Secure Shell Connection. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1.1 |
sshConnMajorVersionThe SSH major version.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1.2 |
sshConnMinorVersionThe SSH minor version.ro Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1.3 |
sshConnStatusThe SSH connection State. negotiationStart(1) means the
SSH is in its negotiation start state, authenticationStart(2)
means the SSH is in authentication start state, sessionStart(3)
means the SSH is in session start State.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1.5 |
sshConnUserNameThe user name of the connection.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1.6 |
sshDisconnectSet the variable to disconnect the connection,
noDisconnect(1) will always be obtained when reading this variable.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1.7 |
sshConnEncryptionTypeStrThe encryption type of the SSH.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.6.6.1.8 |
sshKeySizeThe SSH server key size.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.6.7 |
sshRsaHostKey1The RSA host key segment 1.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.8 |
sshRsaHostKey2The RSA host key segment 2.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.9 |
sshRsaHostKey3The RSA host key segment 3.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.10 |
sshRsaHostKey4The RSA host key segment 4.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.11 |
sshRsaHostKey5The RSA host key segment 5.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.12 |
sshRsaHostKey6The RSA host key segment 6.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.13 |
sshRsaHostKey7The RSA host key segment 7.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.14 |
sshRsaHostKey8The RSA host key segment 8.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.15 |
sshDsaHostKey1The DSA host key segment 1.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.16 |
sshDsaHostKey2The DSA host key segment 2.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.17 |
sshDsaHostKey3The DSA host key segment 3.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.18 |
sshDsaHostKey4The DSA host key segment 4.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.19 |
sshDsaHostKey5The DSA host key segment 5.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.20 |
sshDsaHostKey6The DSA host key segment 6.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.21 |
sshDsaHostKey7The DSA host key segment 7.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.22 |
sshDsaHostKey8The DSA host key segment 8.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.23 |
sshHostKeyGenActionThis variable is for host key generating.
For the set behavior:
Set it to genRsaKey(2) to generate the RSA host key,
and to genDsaKey(3) to generate the DSA host key,
if genBothKeys(4) is set, both RSA and DSA host key are
generated.
For the get behavior:
You will get genRsaKey(2), genDsaKey(3) or
genBothKeys(4) when the key gen action is in progress.
otherwise, you will get noGen(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.24 |
sshHostKeyGenStatusThe result of the last KeyGen status.
if no key gen action has been performed.
you will get unknown(1) status.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.25 |
sshHostKeySaveActionTo save host key from memory to flash.
For the set behavior:
Set it to save(2) to perform the save operation.
For the get behavior:
You will get save(1) when the save action is in progress.
Otherwise, you will get noSave(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.26 |
sshHostKeySaveStatusThe result of the last savekey status.
If no save action has been performed,
you will get unknown(1) status.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.27 |
sshHostKeyDelActionTo delete the host key.
For the set behavior:
Set it to delRsaKey(2) to delete the RSA host key,
to delDsaKey(3) to delete the DSA host key,
or to delBothKeys(4) to delete both RSA and DSA host key.
For the get behavior:
You will get delRsaKey(2), delDsaKey(3) or delBothKeys(4)
when the delete operation is in progress.
Otherwise, you will get noDel(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.28 |
sshUserTableThe conceptual table of all of sshUserEntry. SEQUENCE OF SshUserEntry .1.3.6.1.4.1.21839.2.2.26.1.17.6.29 |
sshUserEntryThe conceptual row for sshUserTable. SshUserEntry .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1 |
sshUserNameUser Name. DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.1 |
sshUserRsaKey1The RSA user key segment 1.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.2 |
sshUserRsaKey2The RSA user key segment 2.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.3 |
sshUserRsaKey3The RSA user key segment 3.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.4 |
sshUserRsaKey4The RSA user key segment 4.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.5 |
sshUserRsaKey5The RSA user key segment 5.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.6 |
sshUserRsaKey6The RSA user key segment 6.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.7 |
sshUserRsaKey7The RSA user key segment 7.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.8 |
sshUserRsaKey8The RSA user key segment 8.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.9 |
sshUserDsaKey1The DSA user key segment 1.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.10 |
sshUserDsaKey2The DSA user key segment 2.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.11 |
sshUserDsaKey3The DSA user key segment 3.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.12 |
sshUserDsaKey4The DSA user key segment 4.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.13 |
sshUserDsaKey5The DSA user key segment 5.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.14 |
sshUserDsaKey6The DSA user key segment 6.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.15 |
sshUserDsaKey7The DSA user key segment 7.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.16 |
sshUserDsaKey8The DSA user key segment 8.ro KeySegment .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.17 |
sshUserKeyDelActionTo delete the user key.
For the set behavior:
Set it to delRsaKey(2) to delete the RSA user key,
to delDsaKey(3) to delete the DSA user key,
or to delBothKeys(4) to delete both RSA and DSA user key.
For the get behavior:
You will get delRsaKey(2), delDsaKey(3) or delBothKeys(4)
when the delete operation is in progress.
Otherwise, you will get noDel(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.6.29.1.18 |
sshRsaHostKeySHA1FingerPrintThe SHA1 finger print of the RSA host key.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.6.30 |
sshRsaHostKeyMD5FingerPrintThe MD5 finger print of RSA host key.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.6.31 |
sshDsaHostKeySHA1FingerPrintThe SHA1 finger print of the DSA host key.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.6.32 |
sshDsaHostKeyMD5FingerPrintThe MD5 finger print of the DSA host key.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.6.33 |
ipFilterMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.9 |
ipFilterSnmpInetTableA list of IP address entries. SEQUENCE OF IpFilterSnmpInetEntry .1.3.6.1.4.1.21839.2.2.26.1.17.9.12 |
ipFilterSnmpInetEntryThis entry includes an IP address range which the system
will allow to connect to this device through SNMP. IpFilterSnmpInetEntry .1.3.6.1.4.1.21839.2.2.26.1.17.9.12.1 |
ipFilterSnmpInetAddressTypeThe type of IP address filter.
Only supports IPv4 and IPv6 address types. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.12.1.1 |
ipFilterSnmpInetAddressStartThe start IP address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.12.1.2 |
ipFilterSnmpInetAddressEndThe end IP address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.12.1.3 |
ipFilterSnmpInetStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.9.12.1.4 |
ipFilterHttpInetTableA list of IP address entries. SEQUENCE OF IpFilterHttpInetEntry .1.3.6.1.4.1.21839.2.2.26.1.17.9.13 |
ipFilterHttpInetEntryThis entry includes an IP address range which the system
will allow to connect to this device through SNMP. IpFilterHttpInetEntry .1.3.6.1.4.1.21839.2.2.26.1.17.9.13.1 |
ipFilterHttpInetAddressTypeThe type of IP address filter .
Only supports IPv4 and IPv6 address types. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.13.1.1 |
ipFilterHttpInetAddressStartThe start IP address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.13.1.2 |
ipFilterHttpInetAddressEndThe end IP address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.13.1.3 |
ipFilterHttpInetStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.9.13.1.4 |
ipFilterTelnetInetTableA list of IP address entries. SEQUENCE OF IpFilterTelnetInetEntry .1.3.6.1.4.1.21839.2.2.26.1.17.9.14 |
ipFilterTelnetInetEntryThis entry includes an IP address range which the system
will allow them to connect to this device through SNMP. IpFilterTelnetInetEntry .1.3.6.1.4.1.21839.2.2.26.1.17.9.14.1 |
ipFilterTelnetInetAddressTypeThe type of IP address filter .
Only supports IPv4 and IPv6 address types. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.14.1.1 |
ipFilterTelnetInetAddressStartThe start IP address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.14.1.2 |
ipFilterTelnetInetAddressEndThe end IP address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.14.1.3 |
ipFilterTelnetInetStatusSetting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.9.14.1.4 |
ipFilterAllClientCtl OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.9.15 |
ipFilterAllClientCtlInetAddressTypeThe type of IP address filter. Only supports IPv4 and IPv6
address types.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.15.1 |
ipFilterAllClientCtlInetAddressStartThe start IP address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.15.2 |
ipFilterAllClientCtlInetAddressEndThe end IP address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.9.15.3 |
ipFilterAllClientCtlActionAction for IP filter control. Set this object to create(2) to
create entries in the ipFilterSnmpInetTable,
ipFilterHttpInetTable and ipFilterTelnetInetTable. Set this
object to destroy(3) to destroy specified entries in the
ipFilterSnmpInetTable, ipFilterHttpInetTable and
ipFilterTelnetInetTable. When the action is finshed, whether
successfully or not, or no action is taken, the value of this
object is always noAction(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.9.15.4 |
userAuthMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.10 |
userAuthEnablePasswordSet enable password or delete enable password. NULL is used to
delete the enable password. The password is starting with
alphanumeric.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.10.3 |
userAuthMethodSet user authencation method for system.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.10.4 |
userAuthTableThis table is for creating the new user. SEQUENCE OF UserAuthEntry .1.3.6.1.4.1.21839.2.2.26.1.17.10.5 |
userAuthEntryEntries in this table correspond to the users entries in system. UserAuthEntry .1.3.6.1.4.1.21839.2.2.26.1.17.10.5.1 |
userAuthUserNameThe name of the user. The user name is starting with alphanumeric.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.10.5.1.1 |
userAuthPasswordSpecifies the user password. zero length input will set the user enrty
without password. If the user is not exist, it will create the user
with the giving password and privilege 0. The password is starting
with alphanumeric.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.10.5.1.2 |
userAuthPrivilegeSpecifies the user level. If the user does not exist, it will create
the user with the given privilege and no password. Privilege 15
indicates system administrator, privilege 0 indicates guest user.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.10.5.1.3 |
userAuthPublicKeyUser public key, the value can be 'RSA' or 'DSA' or 'Both' or 'None'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.10.5.1.4 |
userAuthStatusThis node is used to create the user entry by '1' and to delete one
user entry by '0'.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.10.5.1.5 |
dot1xMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.11 |
dot1xAuthConfigExtTableThe extension table of dot1xAuthConfigTable. SEQUENCE OF Dot1xAuthConfigExtEntry .1.3.6.1.4.1.21839.2.2.26.1.17.11.1 |
dot1xAuthConfigExtEntryThe entry of dot1xAuthConfigExtTable. Dot1xAuthConfigExtEntry .1.3.6.1.4.1.21839.2.2.26.1.17.11.1.1 |
dot1xAuthConfigExtOperModeThe operation mode of dot1x port which allows host
connection to 802.1x-authorized ports.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.11.1.1.1 |
dot1xAuthConfigExtMultiHostMaxCntThe maximum number of hosts when the
dot1xAuthConfigExtOperMode is multiHost(2). When the
operation Mode is singleHost(1), we can ignore this
variables.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.11.1.1.2 |
dot1xAuthConfigExtPortIntrusionActionResponses to intrusion when the authentication is failed;
block-traffic(1) means that to block traffic when the authentication is failed and
guest-vlan(2) means that to join to a guest VLAN when the authentication is failed.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.11.1.1.3 |
dot1xEapolPassThroughWhen this variable is enabled(1), EAPOL frames will
be forwarded to all ports where the Spanning Tree
status is forwarding. When this variable is
disabled(2), EAPOL frames will be discarded. EAPOL
Pass-Through operates when the global status of
802.1X is disabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.11.3 |
aaaMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.12 |
aaaMethodTableContains the settings needed for accounting. SEQUENCE OF AaaMethodEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.1 |
aaaMethodEntryA conceptual row in the aaaMethodTable. AaaMethodEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1 |
aaaMethodIndexSpecifies the index for the entry. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1.1 |
aaaMethodNameName for the method.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1.2 |
aaaMethodGroupNameName for the server to use, pointing to aaaRadiusGroupName
or aaaTacacsPlusGroupName.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1.3 |
aaaMethodModestart-stop(1),sends a 'start' accounting notice at the beginning of a process and
a 'stop' accounting notice at the end of a process. The 'start' accounting record
is sent in the background. The requested user process begins regardless of whether or not
the 'start' accounting notice was received by the accounting server.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1.4 |
aaaMethodStatusSet to 1 to initiate the aaaMethodTable, 2 to destroy the table.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1.5 |
aaaMethodClientTypedot1x(1): Provides accounting service for 802.1x activity;
exec(2): Provides accounting service for EXEC connection
such as Telnet, SSH or console; commands(3): Provides
accounting service for command privileges.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1.6 |
aaaMethodPrivilegeLevelSpecifies the privilege level for the entry.
When aaaMethodClientType is in the mode of command(3),
the privilege level is enabled to be accessed.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.12.1.1.7 |
aaaRadiusGroupTableUses a subset of RADIUS servers for accounting as defined by the server group SEQUENCE OF AaaRadiusGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.2 |
aaaRadiusGroupEntryA conceptual row of aaaRadiusGroupEntry. AaaRadiusGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.2.1 |
aaaRadiusGroupIndexSpecifies the index for the entry. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.12.2.1.1 |
aaaRadiusGroupServerBitMapIdentifies which RADIUS sever to use, each bit points to each radius server.
80 (1000 0000) point to radius server 1, C0 (11000000) points to radius 1 and radius 2.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.17.12.2.1.2 |
aaaRadiusGroupNameUses a subset of servers for accounting as
defined by the server group. The same name as aaaTacasPlusGroupName is not allowed.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.12.2.1.3 |
aaaRadiusGroupStatusSet to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.12.2.1.4 |
aaaTacacsPlusGroupTableUses a subset of TACACS+ servers for accounting as defined by the server group SEQUENCE OF AaaTacacsPlusGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.3 |
aaaTacacsPlusGroupEntryA conceptual row of aaaTacacsPlusGroupEntry. AaaTacacsPlusGroupEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.3.1 |
aaaTacacsPlusGroupIndexSpecifies the index for the entry. Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.12.3.1.1 |
aaaTacacsPlusGroupServerBitMapIdentifies which TACACS+ sever to use.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.26.1.17.12.3.1.2 |
aaaTacacsPlusGroupNameUses a subset of servers for accounting as
defined by the server group. We can't have the same name as aaaRadiusGroupNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.12.3.1.3 |
aaaTacacsPlusGroupStatusSet to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.12.3.1.4 |
aaaUpdateSpecifies the periodic interim accounting records to be sent
to the accounting server and periodic intervals to send accounting update records(in minutes).rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.12.4 |
aaaAccountTableSpecifies an interface or a set of interfaces that the
accounting method list will be applied to. SEQUENCE OF AaaAccountEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.5 |
aaaAccountEntryA conceptual row of aaaAccountTable. AaaAccountEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.5.1 |
aaaAccountIfIndexDefined as the ifIndex InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.12.5.1.1 |
aaaAccountMethodNameSpecifies the name of the list of accounting methods to use.
If no method name is specified, the system uses the default.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.12.5.1.2 |
aaaAccountProtocolGet the protocol type of a list method to know which server (RADIUS or TACACS+) is in use.ro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.12.5.1.3 |
aaaAccountStatusSet to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.12.5.1.4 |
aaaCommandPrivilegesTableContains the settings needed for command privileges. SEQUENCE OF AaaCommandPrivilegesEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.8 |
aaaCommandPrivilegesEntryA conceptual row in the aaaCommandPrivilegesTable. AaaCommandPrivilegesEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.8.1 |
aaaCommandPrivilegesLevelSpecifies the privilege level index for the entry. INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.12.8.1.1 |
aaaCommandPrivilegesInterfaceIndexSpecifies the interface index for the entry. Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.12.8.1.2 |
aaaCommandPrivilegesMethodNameSpecifies the method name in the lists under
the mode of command privileges.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.12.8.1.3 |
aaaAccExecTableSpecifies an interface or a set of interfaces that the
accounting method list will be applied to. SEQUENCE OF AaaAccExecEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.9 |
aaaAccExecEntryA conceptual row of aaaAccExecTable. AaaAccExecEntry .1.3.6.1.4.1.21839.2.2.26.1.17.12.9.1 |
aaaAccExecIndexThe method of accessing CLI management. Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.12.9.1.1 |
aaaAccExecMethodNameSpecifies the name of the list of accounting methods to use.
If no method name is specified, the system uses the default.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.12.9.1.2 |
networkAccessMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.13 |
networkAccessPortTableA table contains the information of network access about every port. SEQUENCE OF NetworkAccessPortEntry .1.3.6.1.4.1.21839.2.2.26.1.17.13.2 |
networkAccessPortEntryA conceptual row in the networkAccessPort table. NetworkAccessPortEntry .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1 |
networkAccessPortPortIndexThe port and the trunk (excluding trunk members) interface of the
portTable. The interface identified by a particular value of this port
index is the same interface identified by the same value of
ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1.1 |
networkAccessPortDynamicVlanSets enabled(1) to enable dynamic VLAN assigment and
sets disabled(2) to disable dynamic VLAN assigment.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1.2 |
networkAccessPortMaxMacCountSpecifies the maximum number of authenticated MAC address.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1.3 |
networkAccessPortModeSpecifies the secure port mode. enabled(1) means that Mac address
authentication is used and disabled(2) means that the authentication is disabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1.4 |
networkAccessPortMacFilterSpecifies the MAC filter ID, Set this variable to zero to
disable MAC filter.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1.5 |
networkAccessPortGuestVlanSpecifies the guest VLAN ID. To disable the VLAN, set the value to 0.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1.6 |
networkAccessPortDynamicQosSet this object to enabled(1) to enable Dynamic QoS.
Set this object to disabled(2) to disable Dynamic QoS.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.2.1.10 |
networkAccessClearMacAddressMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.13.3 |
networkAccessClearMacAddressAttributeAttribute for clearing Mac address. Specifies the certain attribute
in Mac address table. all(1) indicates both reauthorized and learnt
secure MAC address; static(2) indicates reauthorized MAC address;
dynamic(3) indicates learnt secure MAC address.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.13.3.1 |
networkAccessClearMacAddressMacAddressSpecifies MAC address in the MAC address table for clearing
MAC address. '000000' represents that no MAC address is specified.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.13.3.2 |
networkAccessClearMacAddressPortThe specifies port in the MAC address table for clearing MAC address.
'0' represents that no port is specified.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.13.3.3 |
networkAccessClearMacAddressActionAction for clearing MAC address . When setting this object to clear(2)
to begin the clearing MAC address operation, a particular MAC address
is cleared from the MAC address table. When the action is finshed whether
or not it is successful or no action is taken, the value of this object
is always noclear(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.13.3.4 |
networkAccessMacAddressTableContains the information of network access MAC addresses. SEQUENCE OF NetworkAccessMacAddressEntry .1.3.6.1.4.1.21839.2.2.26.1.17.13.4 |
networkAccessMacAddressEntryA conceptual row in the networkAccessMacAddress table. NetworkAccessMacAddressEntry .1.3.6.1.4.1.21839.2.2.26.1.17.13.4.1 |
networkAccessMacAddressAddressSpecifies the authenticated MAC address. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.13.4.1.1 |
networkAccessMacAddressPortSpecifies the port of authenticated MAC address. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.4.1.2 |
networkAccessMacAddressInetAddressTypeThis object indicates the type of IP address denoted in
networkAccessMacAddressRadiusServerInetAddress type.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.4.1.3 |
networkAccessMacAddressRadiusServerInetAddressDisplays the IP address of radius server that authenticates
the specified Mac address.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.4.1.4 |
networkAccessMacAddressTimeDisplays the authentication time of the authenticated MAC address.
The following form is a text string; 'yyyy MMm DDd HHh MMm SSs'.
'yyyy' is a four-digit year. 'MM' is a month. A single-digit month is
preceded by a zero. 'DD' is the day of a month. A single-digit day
is preceded by the value zero. 'HH', 'MM' and 'SS' are hour,
minute, and second respectively. A single-digit hour, minute,
and second are preceded by a zero value. An example is:
'2001y 01m 01d 00h 04m 43s'.ro DisplayString .1.3.6.1.4.1.21839.2.2.26.1.17.13.4.1.5 |
networkAccessMacAddressAttributeDisplays the attribute of an authenticated MAC address.
static(1) indicates resauthorized secure MAC address.
dynamic(2) indicates learnt secure MAC address.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.13.4.1.6 |
networkAccessAgingSet this object to enabled(1) to enable MAC address aging feature.
Set this object to disabled(2) to disable MAC address aging feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.13.5 |
networkAccessMacFilterWithMaskTableContains the settings for MAC filter. SEQUENCE OF NetworkAccessMacFilterWithMaskEntry .1.3.6.1.4.1.21839.2.2.26.1.17.13.6 |
networkAccessMacFilterWithMaskEntryA conceptual row in the networkAccessMacFilterWithMaskTable. NetworkAccessMacFilterWithMaskEntry .1.3.6.1.4.1.21839.2.2.26.1.17.13.6.1 |
networkAccessMacFilterWithMaskIDSpecifies the MAC filter ID. INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.13.6.1.1 |
networkAccessMacFilterWithMaskMacAddressSpecifies the MAC address to be filtered. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.13.6.1.2 |
networkAccessMacFilterWithMaskMacAddressMaskSpecifies the MAC mask to be filtered. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.26.1.17.13.6.1.3 |
networkAccessMacFilterWithMaskStatusSet this object to valid(1) to create an entry.
Set this object to invalid(2) to destroy an entry.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.17.13.6.1.4 |
macAuthMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.14 |
macAuthReauthTimeSpecifies the reauthentication time period.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.14.1 |
macAuthPortTableContains the settings for mac authentication of each port. SEQUENCE OF MacAuthPortEntry .1.3.6.1.4.1.21839.2.2.26.1.17.14.2 |
macAuthPortEntryA conceptual row in the macAuthPort table. MacAuthPortEntry .1.3.6.1.4.1.21839.2.2.26.1.17.14.2.1 |
macAuthPortIndexThe port and the trunk (including trunk members) interface of the
port table. The interface identified by a particular value of this
index is the same interface identified by the same value
of ifIndex in the IF-MIB. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.14.2.1.1 |
macAuthPortMaxMacCountSpecifies the maximum number of authenticated MAC addresses for MAC authentication.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.14.2.1.2 |
macAuthPortIntrusionActionResponses to intrusion when the authentication is failed.
block-traffic(1) : denies network access to an unauthorized client;
pass-traffic(2) : allows unauthorized clients to the access network.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.14.2.1.3 |
webAuthMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.15 |
webAuthSystemAuthControlSets enabled(1) to enable WebAuth feature and
sets disabled(2) to disable WebAuth feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.1 |
webAuthSessionTimeoutFor authenticated success users, they can use internet
service during a certain period. Whenever this period expires,
users need to be re-authenticated again. This period is
called session time.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.15.5 |
webAuthQuietPeriodSpecifies the re-authentication interval when the authentication
fail attempts reach the webAuthLoginAttempts value. Unauthenticated
user won't be authenticated during this period.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.15.6 |
webAuthLoginAttemptsSpecifies the counter that configures the authentication fail times
for a client. If authentication fail times reaches the specified
value, the client are not allowed to login for some period.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.15.7 |
webAuthReauthenticateMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.15.8 |
webAuthReauthenticatePortSpecifies the port to re-authenticate for all of its
authenticated hosts.rw INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.15.8.1 |
webAuthReauthenticateInetAddressTypeSpecifies host type to re-authenticate.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.8.2 |
webAuthReauthenticateInetAddressSpecificies host to re-authenticate.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.8.3 |
webAuthReauthenticateActionAction for WebAuth re-authenication. When setting this object to
reauth(2) to begin the re-authenticated operation, a particular
user is re-authenticated. When the action is finshed whether it is
successfully, or no action is taken, the value of this
object is always noReauth(1).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.15.8.4 |
webAuthPortConfigTableContains the settings for web authentication of each port. SEQUENCE OF WebAuthPortConfigEntry .1.3.6.1.4.1.21839.2.2.26.1.17.15.9 |
webAuthPortConfigEntryA conceptual row in the webAuthPortConfigTable. WebAuthPortConfigEntry .1.3.6.1.4.1.21839.2.2.26.1.17.15.9.1 |
webAuthPortConfigPortIndexThe port number of the port that may specify certain entry in the table which contains web authentication information. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.9.1.1 |
webAuthPortConfigStatusSets enabled(1) to enable web authentication feature for each port and
sets disabled(2) to disable web authentication for each port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.9.1.2 |
webAuthPortConfigAuthenticatedHostCountDisplays the authenticated host counts for each portro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.15.9.1.3 |
webAuthPortInfoTableContains the information for web authentication of each port. SEQUENCE OF WebAuthPortInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.17.15.10 |
webAuthPortInfoEntryA conceptual row in the webAuthPortTable. WebAuthPortInfoEntry .1.3.6.1.4.1.21839.2.2.26.1.17.15.10.1 |
webAuthPortInfoPortIndexThe port number for which this entry contains web authentication information. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.10.1.1 |
webAuthPortInfoPortAuthSuccessIndexThe authentication success number of port for which this entry contains web authentication information. INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.15.10.1.2 |
webAuthPortInfoInetAddressTypeThis object indicates the type of IP address denoted in webAuthPortInfoIpAddress type.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.10.1.3 |
webAuthPortInfoInetAddressThe IP address which may specify the entry containing web authentication information.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.15.10.1.4 |
webAuthPortInfoRemainingSessiontimeThe remaining session time for authenticated hosts. During this
period, they may use internet resource. When the session time expires, they
will need to re-authenticate again.ro INTEGER .1.3.6.1.4.1.21839.2.2.26.1.17.15.10.1.5 |
webAuthPortInfoStatusDisplays the web authentication status for each port.
authenticated (1) means the user is authenticated.ro Enumeration .1.3.6.1.4.1.21839.2.2.26.1.17.15.10.1.6 |
dosMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1 |
dosEchoChargen OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.1 |
dosEchoChargenStatusThe status of Echo/Chargen protection. Set this to
enabled(1) to enable the feature, and set this to
disabled(2) to disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.1.1 |
dosEchoChargenRateLimitInKiloValue of the rate limit for Echo/Chargen packets. The unit
is kilobits per second.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.1.2 |
dosSmurf OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.3 |
dosSmurfStatusThe status of Smurf protection. Set this to enabled(1)
to enable the feature, and set this to disabled(2) to
disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.3.1 |
dosTcpFlooding OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.4 |
dosTcpFloodingStatusThe status of TCP flooding protection. Set this to
enabled(1) to enable the feature, and set this to
disabled(2) to disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.4.1 |
dosTcpFloodingRateLimitInKiloValue of the rate limit for TCP flooding packets. The
unit is kilobits per second.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.4.2 |
dosTcpNullScan OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.5 |
dosTcpNullScanStatusThe status of TCP Null-scan protection. Set this to
enabled(1) to enable the feature, and set this to
disabled(2) to disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.5.1 |
dosTcpSynFinScan OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.6 |
dosTcpSynFinScanStatusThe status of TCP SYN FIN scan protection. Set this to
enabled(1) to enable the feature, and set this to
disabled(2) to disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.6.1 |
dosTcpXmasScan OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.7 |
dosTcpXmasScanStatusThe status of TCP Xmas-scan protection. Set this to
enabled(1) to enable the feature, and set this to
disabled(2) to disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.7.1 |
dosUdpFlooding OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.8 |
dosUdpFloodingStatusThe status of UDP flooding protection. Set this to
enabled(1) to enable the feature, and set this to
disabled(2) to disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.8.1 |
dosUdpFloodingRateLimitInKiloValue of the rate limit for UDP flooding packets. The
unit is kilobits per second.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.8.2 |
dosWinNuke OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.9 |
dosWinNukeStatusThe status of WinNUKE protection. Set this to enabled(1)
to enable the feature, and set this to disabled(2) to
disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.9.1 |
dosWinNukeRateLimitInKiloValue of the rate limit for WinNUKE packets. The unit is
kilobits per second.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.9.2 |
dosTcpUdpPortZero OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.11 |
dosTcpUdpPortZeroStatusThe status of checking for TCP/UDP packets with port 0.
Set this to enabled(1) to enable the feature, and
set this to disabled(2) to disable the feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.17.16.1.11.1 |
layer3Mgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.18 |
arpMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.18.1 |
arpCacheDeleteAllTo delete all dynamic entries in the ARP cache, write this variable
to delete(1). Writing this variable to noDelete(2) has no effect on
the device. When read, this variable always returns noDelete(2).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.18.1.1 |
arpCacheTimeoutTimeout is provided for entries in the ARP Cache. It is for dynamic
mapping only. Static mapping by creating an entry that associates a
logical address with a physical address is never aged out.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.18.1.2 |
arpTrafficStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.18.1.3 |
arpStatSendRequestPacketsThe number of ARP Request packets sent by the ARP process.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.18.1.3.1 |
arpStatRcvRequestPacketsThe number of ARP Request packets received by the ARP process.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.18.1.3.2 |
arpStatSendReplyPacketsThe number of ARP Reply packets sent by the ARP process.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.18.1.3.3 |
arpStatRcvReplyPacketsThe number of ARP Reply packets received by the ARP process.ro Counter32 .1.3.6.1.4.1.21839.2.2.26.1.18.1.3.4 |
arpProxyArpTableA list of Proxy ARP status. This table has entries for all static
VLANs. SEQUENCE OF ArpProxyArpEntry .1.3.6.1.4.1.21839.2.2.26.1.18.1.4 |
arpProxyArpEntryAn entry in the table, containing information about Proxy ARP
configuration. ArpProxyArpEntry .1.3.6.1.4.1.21839.2.2.26.1.18.1.4.1 |
arpProxyArpIfIndexThis is defined as a VLAN interface.
A routing interface is a VLAN that binds an IP subnet. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.1.4.1.1 |
arpProxyArpStatusEnable or disable proxy ARP process on an interface.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.1.4.1.2 |
ripMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.18.2 |
ripBasicTimers OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.18.2.1 |
ripUpdateBasicTimerThe update time in seconds controls the advertising of regular update
messages. In the real implementation, the actual timer is this value
offset by a random time (+/-50%) each time it is set.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.18.2.1.1 |
ripTimeoutBasicTimerThe timeout timer in seconds governs the validity of a route. It is
initialized when a route is established, and any time an update
message is received for the route. If the setting time elapses from
the last time the timeout was initialized, the route is considered to
have expired, and the hop count of the route is set to infinite. It
should be at least three times the value of the update timer.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.18.2.1.2 |
ripGarbageCollectionBasicTimerWhen the information about a route becomes invalid, the system does
not immediately purge that route from its table. Instead, it continues
to advertise the route with an infinite metric. At the same time, the
garbage-collection timer is set for that route. When the count reaches
zero, the route is purged from the table. This timer allows neighbors
to become aware of the invalidity of a route prior to purging.rw Integer32 .1.3.6.1.4.1.21839.2.2.26.1.18.2.1.3 |
ripRoutingProcessStatusEnable or disable RIP routing process on a system.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.2.2 |
ripGlobalRouterVersionTo specify a RIP version used globally by the router. If interface
version is configurated, router will use the interface configuration;
and if version is not configurated on interface, router will use this
global version; and if both interface and global are not configurated,
router will use interface's default configuration.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.18.2.3 |
ripInstabilityPreventingTableA list of RIP instability preventing status. SEQUENCE OF RipInstabilityPreventingEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.4 |
ripInstabilityPreventingEntryAn entry in the table, containing information about RIP instability
preventing configuration.
The ifIndex index is a VLAN's ifIndex. RipInstabilityPreventingEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.4.1 |
ripIfindexThis is defined as a VLAN interface.
A routing interface is a VLAN and an IP subnet bound to it. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.2.4.1.1 |
ripSplitHorizonStatusEnable or disable RIP poison reverse on an interface.rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.18.2.4.1.2 |
ripStatisticsResetWrite it to reset(1), the following objects in RFC 1724 should be
reset:
1. Global Counters:
'rip2GlobalRouteChanges',
'rip2GlobalQueries'.
2. Interface Status Table, for each 'rip2IfStatAddress':
'rip2IfStatRcvBadPackets',
'rip2IfStatRcvBadRoutes',
'rip2IfStatSendUpdates'
3. Peer Table, for each 'rip2PeerAddress' and 'rip2PeerDomain',
'rip2PeerRcvBadPackets',
'rip2PeerRcvBadRoutes'
When read this value always is noReset(2).rw Enumeration .1.3.6.1.4.1.21839.2.2.26.1.18.2.5 |
ripNetwork OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.18.2.6 |
ripNetworkByInetAddrTableThe RIP network address table. SEQUENCE OF RipNetworkByInetAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.1 |
ripNetworkByInetAddrEntryA conceptual row of the ripNetworkByInetAddrTable. RipNetworkByInetAddrEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.1.1 |
ripNetworkByInetAddrAddressTypeThe RIP Network address type. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.1.1.1 |
ripNetworkByInetAddrAddressThe RIP Network address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.1.1.2 |
ripNetworkByInetAddrPfxLenNetwork prefix length. InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.1.1.3 |
ripNetworkByInetAddrStatusSet this variable to create or destroy a RIP network address.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.1.1.4 |
ripNetworkByIfindexTableThe RIp network ifindex table. SEQUENCE OF RipNetworkByIfindexEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.2 |
ripNetworkByIfindexEntryA conceptual row of the ripNetworkByIfindexTable. RipNetworkByIfindexEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.2.1 |
ripNetworkIfindexThis is defined as a layer3 interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.2.1.1 |
ripNetworkByIfindexStatusSet this variable to create or destroy a RIP network ifindex table.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.18.2.6.2.1.2 |
ripDistributeListTableThe RIP distribute list table. It's used to filter incoming or
outgoing route updates using the access-list or prefix-list. SEQUENCE OF RipDistributeListEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.7 |
ripDistributeListEntryA conceptual row of the ripDistributelistTable. RipDistributeListEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.7.1 |
ripDistributeListInterfaceIndexThe index of the interface on which distribute-list is applied, If
index is 0, the filter will be applied to all the interfaces. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.26.1.18.2.7.1.1 |
ripDistributeListTypeType of distribute-list applied: access-list or prefix-list. Enumeration .1.3.6.1.4.1.21839.2.2.26.1.18.2.7.1.2 |
ripDistributeListIncomingRouteFilterNameSpecifies access-list or prefix-list name to filter incoming routing
updates.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.18.2.7.1.3 |
ripDistributeListOutgoingRouteFilterNameSpecifies access-list or prefix-list name to filter outgoing routing
updates.rw DisplayString .1.3.6.1.4.1.21839.2.2.26.1.18.2.7.1.4 |
ripDistributeListStatusSet this variable to create or destroy a distribute list.rw ValidStatus .1.3.6.1.4.1.21839.2.2.26.1.18.2.7.1.5 |
ripRedistributeTableThe RIP Redistribute table. Config rip redistribute type, metric. SEQUENCE OF RipRedistributeEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.8 |
ripRedistributeEntryA conceptual row of the ripRedistributeTable. RipRedistributeEntry .1.3.6.1.4.1.21839.2.2.26.1.18.2.8.1 |
routeMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.18.5 |
sysLogMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.19 |
lineMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.20 |
sysTimeMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.23 |
fileMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.24 |
dnsMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.26 |
poeMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.28 |
stormMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.33 |
sysResourceMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.39 |
mvrMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.44 |
dhcpSnoopMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.46 |
clusterMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.47 |
ipSrcGuardMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.48 |
mldSnoopMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.54 |
dynamicArpInspectionMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.56 |
timeRangeMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.61 |
lbdMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.63 |
mDnsMgt OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.1.75 |
AXprimoM210Notifications OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.2 |
AXprimoM210-08T OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.101 |
AXprimoM210-08P OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.26.103 |
ripRedistributeProtocolProtocol redistributed to Intermediate System:
connected
static
ospf
bgp
::= { ripRedistributeEntry 1 }
ripRedistributeMetric OBJECT-TYPE
SYNTAX Integer32(0..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION Enumeration .214 |