AX260A
AI MIB Summary
Standard SNMP MIB module defining data structures for AX260A.
923
Objects
Active
Status
12
Dependencies
Imported Objects
Objects
923 total| Object Name |
|---|
alaxala OBJECT IDENTIFIER .1.3.6.1.4.1.21839 |
OSPF-MIB Unknown .1.3.6.1.4.1.21839 |
alaxalaProductId OBJECT IDENTIFIER .1.3.6.1.4.1.21839.1 |
axSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.21839.1.2 |
ax260a OBJECT IDENTIFIER .1.3.6.1.4.1.21839.1.2.23 |
ax260aSystemMsgTrapSystem message is displayed. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.1 |
ax260aTemperatureTrapA ax260aTemperatureTrap is sent if the
temperature measured at a given testpoint is outside
the normal range for the testpoint (i.e. is at the warning,
critical, or shutdown stage). TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.4 |
ax260aAirFanStopTrapThis trap indicates a fan failure. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.8 |
ax260aPowerSupplyFailureTrapThis trap indicates one ( or more ) of power supplies failure. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.9 |
ax260aLoginSuccessTrapThis trap indicates success of user log in. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.10 |
ax260aLoginFailureTrapThis trap indicates failure of user log in. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.11 |
ax260aLogoutTrapThis trap indicates success of following log out.
'logout' command, 'exit' command, 'quit' command. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.12 |
ax260aMemoryUsageTrapThis indicates available memory is fewer than lower limit. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.13 |
ax260aFrameErrorReceiveTrapThis indicates frame receive error. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.18 |
ax260aFrameErrorSendTrapThis indicates frame send error. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.19 |
ax260aBroadcastStormDetectTrapThis indicates decection on broad-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.20 |
ax260aMulticastStormDetectTrapThis indicates decection on multi-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.21 |
ax260aUnicastStormDetectTrapThis indicates decection on uni-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.22 |
ax260aBroadcastStormPortInactivateTrapThis indicates the port inactivated for decection on broad-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.23 |
ax260aMulticastStormPortInactivateTrapThis indicates the port inactivated for decection on multi-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.24 |
ax260aUnicastStormPortInactivateTrapThis indicates the port inactivated for decection on uni-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.25 |
ax260aBroadcastStormRecoverTrapThis indicates the end of broad-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.26 |
ax260aMulticastStormRecoverTrapThis indicates the end of multi-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.27 |
ax260aUnicastStormRecoverTrapThis indicates the end of uni-cast storm. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.28 |
ax260aEfmoamUdldPortInactivateTrapEfmoam udld port inactivate trap. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.29 |
ax260aEfmoamLoopDetectPortInactivateTrapEfmoam loop detect port inactivate trap. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.30 |
ax260aDot1xFailureTrapPrivate trap of 802.1X authentication failure. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.31 |
ax260aDot1xEventTrapPrivate trap of 802.1X authentication event. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.32 |
ax260aWauthFailureTrapPrivate trap of Web authentication failure. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.33 |
ax260aWauthEventTrapPrivate trap of Web authentication event. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.34 |
ax260aMauthFailureTrapPrivate trap of Mac authentication failure. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.35 |
ax260aMauthEventTrapPrivate trap of Mac authentication event. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.36 |
ax260aDot1xSystemTrapPrivate trap of 802.1X authentication system. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.37 |
ax260aWauthSystemTrapPrivate trap of Web authentication system. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.38 |
ax260aMauthSystemTrapPrivate trap of Mac authentication system. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.39 |
ax260aAxrpStateTransitionTrapWhen the state of the ring of ALAXALA Ring Protocol (trouble watch and restoration watch) changes between each state. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.40 |
ax260aAxrpMultiFaultDetectionStartTrapWhen you make the multiple fault detection function of Ring Protocol effective. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.41 |
ax260aAxrpMultiFaultDetectionStateTransitionTrapWhen the state of the ring of ALAXALA Ring Protocol (multiple fault detection and restoration watch) changes between each state. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.42 |
ax260aL2ldLinkDownWhen the operation of the interface changes from ACTIVE(state that can be communicated)
into DISABLE (state that cannot be communicated) by the L2 loop detection. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.51 |
ax260aL2ldLinkUpWhen the operation of the interface changes from DISABLE (state that cannot be communicated)
into ACTIVE (state that can be communicated) by the automatic restoration function of the L2 loop detection. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.52 |
ax260aL2ldLoopDetectionWhen you detect the L2 loop. It notifies every 60 seconds when the state of the L2 loop continues. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.53 |
ax260aUlrChangeSecondaryWhen secondary port changed to active port. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.87 |
ax260aUlrChangePrimaryWhen primary port changed to active port. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.88 |
ax260aDeviceErrorTrapThis indicates decection on Device Error. TRAP-TYPE .1.3.6.1.4.1.21839.1.2.23.0.90 |
alaxalaMib OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2 |
axsEx OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2 |
axsMib OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1 |
axsStats OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.1 |
axsIfStats OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.1.4 |
axsIfStatsTableA table containing extension statistics for more than 100,000,000
bps interface. SEQUENCE OF AxsIfStatsTableEntry .1.3.6.1.4.1.21839.2.2.1.1.4.1 |
axsIfStatsEntryAn entry containing extension statistics for interface. AxsIfStatsTableEntry .1.3.6.1.4.1.21839.2.2.1.1.4.1.1 |
axsIfStatsIndexThis object value is same as Ifindex which interface index
of a system. INTEGER .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.1 |
axsIfStatsNameInterfaces name. Same as ifDescr.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.2 |
axsIfStatsInMegaOctetsNumber of octets that received on the interface. This value is
displayed in mega-octets(M). Value of 0 through 999,999 are rounded
down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.3 |
axsIfStatsInUcastMegaPktsNumber of subnetwork-unicast packets that received on the interface.
This value is displayed in mega-packets(M).Value of 0 through 999,999
are rounded down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.4 |
axsIfStatsInMulticastMegaPktsNumber of multicast mega-packets that received on the interface.
this value is displayed in mega-packets(M).Value of 0 through 999,999
are rounded down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.5 |
axsIfStatsInBroadcastMegaPktsThe number of non-unicast packets delivered to a higher-layer
protocol. The value is displayed in mega-packets (M). Value of 0
through 999,999 are rounded down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.6 |
axsIfStatsOutMegaOctetsThe total number of octets transmitted out of the interface.
The value is displayed in mega-octets(M). Value of 0 through 999,999
are rounded down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.7 |
axsIfStatsOutUcastMegaPktsThe total number of packets that higher-level protocols requested
be transmitted to a subnetwork-unicast address.The value is displayed
in mega packets(M). Value of 0 through 999,999 are rounded down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.8 |
axsIfStatsOutMulticastMegaPktsNumber of multicast packets that transmitted on the interface.
This value is displayed in mega-packets(M). Value of 0 through
999,999 are rounded down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.9 |
axsIfStatsOutBroadcastMegaPktsNumber of broadcast packets that transmitted on the interface.
This value is displayed in mega-packets(M). Value of 0 through
999,999 are rounded down.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.10 |
axsIfStatsHighSpeedA circuit speed.This value is displayed in mega-bps[Mbps].
Round off the 1,000,000bps.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.4.1.1.11 |
axsQoS OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.1.6 |
axsEtherTxQoS OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.1.6.1 |
axsEtherTxQoSStatsTableA collection of QoS statistics kept for a particular
Ethernet interface. SEQUENCE OF AxsEtherTxQoSStatsEntry .1.3.6.1.4.1.21839.2.2.1.1.6.1.1 |
axsEtherTxQoSStatsEntryAn entry containing QoS statistics for a particular
Ethernet interface. AxsEtherTxQoSStatsEntry .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1 |
axsEtherTxQoSStatsIndexIdentified by a particular value of this
index is same value of ifIndex.Its value ranges
between 1 and the value of ifNumber. INTEGER .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1.1 |
axsEtherTxQoSStatsMaxQnumMax length of queue for an ethernet interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1.2 |
axsEtherTxQoSStatsLimitQlenThe limit length of outband queue for an ethernet interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1.3 |
axsEtherTxQoSStatsTotalOutFramesThe total number of packets transmitted out of the
interface.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1.4 |
axsEtherTxQoSStatsTotalOutBytesHighThe total number of octets transmitted out of the
interface.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1.5 |
axsEtherTxQoSStatsTotalOutBytesLowThe total number of octets transmitted out of the
interface.ro Counter .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1.6 |
axsEtherTxQoSStatsTotalDiscardFramesThe number of outbound packets which were chosen
to be discarded .ro Counter .1.3.6.1.4.1.21839.2.2.1.1.6.1.1.1.7 |
axsEtherTxQoSStatsQueueTableA collection of priority queue statistics. SEQUENCE OF AxsEtherTxQoSStatsQueueEntry .1.3.6.1.4.1.21839.2.2.1.1.6.1.2 |
axsEtherTxQoSStatsQueueEntryA entry of priority queue statistics. AxsEtherTxQoSStatsQueueEntry .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1 |
axsEtherTxQoSStatsQueueIndexIdentified by a particular value of this
index is same value of ifIndex.Its value ranges
between 1 and the value of ifNumber. INTEGER .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.1 |
axsEtherTxQoSStatsQueueQueIndexAn index that uniquely identifies the particular
queue.Its value ranges between 1 and the value of
axsEtherTxQoSStatsMaxQnum. INTEGER .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.2 |
axsEtherTxQoSStatsQueueQlenA length of outbound priority queue for a interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.3 |
axsEtherTxQoSStatsQueueMaxQlenMax length of outband priority queue for a interface since
system was up.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.4 |
axsEtherTxQoSStatsQueueDiscardFramesClass1The number of discard frames in the discard class
1 of output priority queue.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.5 |
axsEtherTxQoSStatsQueueDiscardFramesClass2The number of discard frames in the discard class
2 of output priority queue.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.6 |
axsEtherTxQoSStatsQueueDiscardFramesClass3The number of discard frames in the discard class
3 of output priority queue.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.7 |
axsEtherTxQoSStatsQueueDiscardFramesClass4The number of discard frames in the discard class
4 of output priority queue.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.1.6.1.2.1.8 |
axsEthShaper OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.1.6.4 |
axsEthShaperAgQue OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.1.6.5 |
axsDHCP OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.1.10 |
axsDHCPAddrValueThe number of IP addresses which are available
within this Router.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.1.10.1 |
axsDHCPFreeAddrValueThe number of IP addresses which are available
within this Router. May be expressed as either
an absolute value.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.1.10.2 |
axsGsrp OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.4 |
axsGsrpGroupTableThe table containing GSRP group information. SEQUENCE OF AxsGsrpGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.1 |
axsGsrpGroupEntryThe list of GSRP group information. AxsGsrpGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.1.1 |
axsGsrpGroupIdGSRP group identifier. INTEGER .1.3.6.1.4.1.21839.2.2.1.4.1.1.1 |
axsGsrpGroupRowStatusValid/Invalid state of this entry. Valid(1) fixedro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.4.1.1.2 |
axsGsrpMacAddressThe Media Access Control Address of this equipment.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.4.1.1.3 |
axsGsrpAdvertiseHoldTimeHolding time of the Advertise frame (milli second).ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.1.1.4 |
axsGsrpAdvertiseIntervalInterval between transmitting the Advertise frame (milli second).ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.1.1.5 |
axsGsrpSelectionPatternMaster/Backup selection pattern. Ports-Priority-MAC(1) Priority-Ports-MAC(2)ro Enumeration .1.3.6.1.4.1.21839.2.2.1.4.1.1.6 |
axsGsrpLayer3RedundancyThe status of layer 3 redundancy-change.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.4.1.1.7 |
axsGsrpVlanGroupTableThe table containing GSRP VLAN group information. SEQUENCE OF AxsGsrpVlanGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.2 |
axsGsrpVlanGroupEntryThe list of GSRP VLAN group information. AxsGsrpVlanGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.2.1 |
axsGsrpVlanGroupIdGSRP VLAN group number(1~8) INTEGER .1.3.6.1.4.1.21839.2.2.1.4.2.1.1 |
axsGsrpVlanGroupRowStatusValid/Invalid state of this entry. Valid(1) fixedro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.4.2.1.2 |
axsGsrpStateThe state of GSRP group..ro Enumeration .1.3.6.1.4.1.21839.2.2.1.4.2.1.3 |
axsGsrpPriorityConfigured priority.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.2.1.4 |
axsGsrpActivePortsThe number of port which is link-up in monitored port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.2.1.5 |
axsGsrpTransitionToMasterCountsThe number of times which shifted to the master state from the backup state.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.2.1.6 |
axsGsrpTransitionFromMasterCountsThe number of times which shifted to the backup state from the master state.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.2.1.7 |
axsGsrpLastTransitionTimeThe last time at which changed in the master state from the backup state or in the backup state from the master state.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.4.2.1.8 |
axsGsrpVirtualMacAddressThe virtual Media Access Control address of the GSRP VLAN group. If the status of layer 3 redundancy-change is off, return 00 00 00 00 00 00ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.4.2.1.9 |
axsGsrpNeighborGroupTableThe table containing stores the GSRP group information on facing equipment. SEQUENCE OF AxsGsrpNeighborGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.3 |
axsGsrpNeighborGroupEntryThe table containing stores the GSRP group information on facing equipment. AxsGsrpNeighborGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.3.1 |
axsGsrpNeighborGroupIdThe GSRP group identifier on the facing equipment. INTEGER .1.3.6.1.4.1.21839.2.2.1.4.3.1.1 |
axsGsrpNeighborMacAddressThe Media Access Control Address of the facing equipment. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.4.3.1.2 |
axsGsrpNeighborAdvertiseHoldTimeHolding time of the Advertise frame on opposite equipment (milli second).ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.3.1.3 |
axsGsrpNeighborAdvertiseIntervalInterval between transmitting the Advertise frame on the facing equipment (milli second).ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.3.1.4 |
axsGsrpNeighborSelectionPatternMaster/Backup selection pattern on the facing equipment. Ports-Priority-MAC(1) Priority-Ports-MAC(2)ro Enumeration .1.3.6.1.4.1.21839.2.2.1.4.3.1.5 |
axsGsrpNeighborVlanGroupTableThe table containing the GSRP VLAN group information on facing equipment. SEQUENCE OF AxsGsrpNeighborVlanGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.4 |
axsGsrpNeighborVlanGroupEntryThe table containing the GSRP VLAN group information on facing equipment. AxsGsrpNeighborVlanGroupEntry .1.3.6.1.4.1.21839.2.2.1.4.4.1 |
axsGsrpNeighborVlanGroupIdGSRP VLAN group number on the facing equipment (1~8). INTEGER .1.3.6.1.4.1.21839.2.2.1.4.4.1.1 |
axsGsrpNeighborStateThe state of GSRP group on the facing equipment. Enumeration .1.3.6.1.4.1.21839.2.2.1.4.4.1.2 |
axsGsrpNeighborPriorityConfigured priority on the facing equipment.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.4.1.3 |
axsGsrpNeighborActivePortsThe number of port which is link-up in monitored port on the facing equipment.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.4.4.1.4 |
axsFdb OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.5 |
axsFdbCounterTableThe table of FDB information. SEQUENCE OF AxsFdbCounterEntry .1.3.6.1.4.1.21839.2.2.1.5.1 |
axsFdbCounterEntryThe entry of FDB information. AxsFdbCounterEntry .1.3.6.1.4.1.21839.2.2.1.5.1.1 |
axsFdbCounterNifIndexIdentified by a particular value of this index
is same value of NIF.Its value ranges between 1
and the value of ax260aNifBoardNumber. INTEGER .1.3.6.1.4.1.21839.2.2.1.5.1.1.1 |
axsFdbCounterLineIndexIdentified by a particular value of this index
is same value of Physical Line.Its value ranges
between 1 and the value of ax260aNifLineNumber. INTEGER .1.3.6.1.4.1.21839.2.2.1.5.1.1.2 |
axsFdbCounterCountsThe number of FDB entries learned on the port.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.5.1.1.3 |
axsFdbCounterTypeThe type of FDB entries learning.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.5.1.1.4 |
axsFdbCounterLimitsThe maximum number of FDB entries that can be learned on the port.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.5.1.1.5 |
axsVlan OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6 |
axsVlanBridge OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6.1 |
axsVlanBridgeBase OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6.1.1 |
axsVBBaseTableAn information table of dot1dBase by VLAN units. SEQUENCE OF AxsVBBaseEntry .1.3.6.1.4.1.21839.2.2.1.6.1.1.1 |
axsVBBaseEntryAn informatin entry of every VLAN ID of axsVBBaseTable. AxsVBBaseEntry .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1 |
axsVBBaseIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.1 |
axsVBBaseBridgeAddressMAC address of VLAN.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.2 |
axsVBBaseNumPortsThe number of ports set at VLAN.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.3 |
axsVBBaseTypeA bridging type VLAN may perform.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.4 |
axsVBBaseVlanIfIndexValue of ifIndex of interface of VLAN.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.5 |
axsVBBaseVlanTypeVLAN type.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.6 |
axsVBBaseVlanIDValue of VID of VLAN-TAG corresponding VLAN.ro VlanIdOrZero .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.7 |
axsVBBaseAssociatedPrimaryVlanReturns VLAN ID of Primary VLAN when private VLAN is used and
the same VLAN is set at secondary VLAN.ro VlanIdOrZero .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.8 |
axsVBBaseIfStatusStatus of interface against upper level protocol of VLAN.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.9 |
axsVBBaseLastChangeValue of sysUpTime which is set when VLAN topology changes.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.10 |
axsVBBasePrivateVlanTypeA private VLAN type of VLAN.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.1.1.1.11 |
axsVBBasePortTableAn information table of dot1dBasePortTable by VLAN units. SEQUENCE OF AxsVBBasePortEntry .1.3.6.1.4.1.21839.2.2.1.6.1.1.2 |
axsVBBasePortEntryA configuration entry of axsVBBaseTable. AxsVBBasePortEntry .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1 |
axsVBBasePortIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.1 |
axsVBBasePortPort number of ports set at VLAN.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.2 |
axsVBBasePortIfIndexValue of ifIndex corresponding ports set at VLAN.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.3 |
axsVBBasePortCircuitIdentifier which identifieds ports when VLAN ports
have the same value as axsVBBasePortIfIndex.ro OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.4 |
axsVBBasePortDelayExceededDiscardsTotal number of discard frame caused by passing delay occured at VLAN ports.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.5 |
axsVBBasePortMtuExceededDiscardsTotal number of discard frame caused by data over flow occured at VLAN ports.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.6 |
axsVBBasePortStateSTP port status of port set at VLAN.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.7 |
axsVBBasePortTaggedStateStatus of VLAN-TAG configuration of ports set at VLAN.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.8 |
axsVBBasePortTranslatedTagIDTranslated ID of VLAN when TAG translation is set.ro VlanIdOrZero .1.3.6.1.4.1.21839.2.2.1.6.1.1.2.1.9 |
axsVlanBridgeStp OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6.1.2 |
axsVBStpTableAn information table of dot1dStpTable by VLAN units. SEQUENCE OF AxsVBStpEntry .1.3.6.1.4.1.21839.2.2.1.6.1.2.1 |
axsVBStpEntryA configuration entry of axsVBStpTable. AxsVBStpEntry .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1 |
axsVBStpIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.1 |
axsVBStpProtocolSpecificationA kind of spanning tree protocol by VLAN units.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.2 |
axsVBStpPriorityPriority value of spanning tree by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.3 |
axsVBStpTimeSinceTopologyChangeElapsed time since topology change of spanning tree by VLAN units.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.4 |
axsVBStpTopChangesThe number of times of topology changes of spanning tree by VLAN units.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.5 |
axsVBStpDesignatedRootRoot bridge identifier of spanning tree by VLAN units.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.6 |
axsVBStpRootCostRoot path cost kept by spanning tree by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.7 |
axsVBStpRootPortRoot port value kept by spanning tree by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.8 |
axsVBStpMaxAgeMaximum aging time kept by spanning tree by VLAN units.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.9 |
axsVBStpHelloTimeHello time kept by spanning tree by VLAN units.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.10 |
axsVBStpHoldTimeHold time kept by spanning tree by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.11 |
axsVBStpForwardDelayTransfer delay time kept by spanning tree by VLAN units.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.12 |
axsVBStpBridgeMaxAgeMaximum aging time used when spanning tree acts as a root bridge by VLAN units.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.13 |
axsVBStpBridgeHelloTimeHello time used when spanning tree act as a root bridge by VLAN units.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.14 |
axsVBStpBridgeForwardDelayTransfer delay time used when spanning tree act as a root bridge by VLAN units.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.1.1.15 |
axsVBStpPortTableAn information table of dot1dStpPortTable by VLAN units. SEQUENCE OF AxsVBStpPortEntry .1.3.6.1.4.1.21839.2.2.1.6.1.2.2 |
axsVBStpPortEntryA configuration entry of axsVBStpPortTable. AxsVBStpPortEntry .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1 |
axsVBStpPortIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.1 |
axsVBStpPortPort number corresponding configuration entry.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.2 |
axsVBStpPortPriorityPriority of port by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.3 |
axsVBStpPortStatePresent status of port by VLAN units.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.4 |
axsVBStpPortEnableValue whether spanning tree is enabled or not at the port by VLAN units.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.5 |
axsVBStpPortPathCostPath cost value of the port by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.6 |
axsVBStpPortDesignatedRootValue of root bridge identifier by VLAN units stored in BPDU from specified bridge.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.7 |
axsVBStpPortDesignatedCostPath cost value of specified port connected to the port by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.8 |
axsVBStpPortDesignatedBridgeBridge identifier of bridge which this port regards as specified bridge by VLAN units.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.9 |
axsVBStpPortDesignatedPortPort identifier of specified bridge connected to this port by VLAN units.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.10 |
axsVBStpPortForwardTransitionsThe number of times of changes from learning status into forwarding status.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.2.2.1.11 |
axsVlanBridgeTp OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6.1.4 |
axsVBTpTableA dot1dTp information table by VLAN units. SEQUENCE OF AxsVBTpEntry .1.3.6.1.4.1.21839.2.2.1.6.1.4.1 |
axsVBTpEntryA configuration entry of axsVBTpTable. AxsVBTpEntry .1.3.6.1.4.1.21839.2.2.1.6.1.4.1.1 |
axsVBTpIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.4.1.1.1 |
axsVBTpLearnedEntryDiscardsThe number of discarded entries because of lack of
not-used domain in filtering data base.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.4.1.1.2 |
axsVBTpAgingTimeTime-out time to aging-out entry of filtering date base which is learned dynamically.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.4.1.1.3 |
axsVBTpFdbTableAn information of dot1dTpFdbTable by VLAN units. SEQUENCE OF AxsVBTpFdbEntry .1.3.6.1.4.1.21839.2.2.1.6.1.4.2 |
axsVBTpFdbEntryA configuration entry of axsVBTpFdbTable. AxsVBTpFdbEntry .1.3.6.1.4.1.21839.2.2.1.6.1.4.2.1 |
axsVBTpFdbIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.4.2.1.1 |
axsVBTpFdbAddressUnicast MAC address of filtering data base entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.6.1.4.2.1.2 |
axsVBTpFdbPortIndicates that it hasn't learnt port number when
port number 0 receives frame having MAC address
as source address which axsVBTpFdbAddress indicates.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.4.2.1.3 |
axsVBTpFdbStatusStatus of filtering data base.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.4.2.1.4 |
axsVBTpPortTableAn information table of dot1dTpPortTable by VLAN units. SEQUENCE OF AxsVBTpPortEntry .1.3.6.1.4.1.21839.2.2.1.6.1.4.3 |
axsVBTpPortEntryAn information entry of axsVBTpPortTable of ports. AxsVBTpPortEntry .1.3.6.1.4.1.21839.2.2.1.6.1.4.3.1 |
axsVBTpPortIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.4.3.1.1 |
axsVBTpPortPort number that indicates which port management
information in the entry corresponds.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.4.3.1.2 |
axsVBTpPortMaxInfoMaximum INFO field size of the port by VLAN units.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.4.3.1.3 |
axsVBTpPortInFramesThe number of reception frame of the port by VLAN units.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.4.3.1.4 |
axsVBTpPortOutFramesThe number of sending frame of the port by VLAN units.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.4.3.1.5 |
axsVBTpPortInDiscardsThe number of reception frame of the port by VLAN units.ro Counter .1.3.6.1.4.1.21839.2.2.1.6.1.4.3.1.6 |
axsVlanBridgeStatic OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6.1.5 |
axsVBStaticTableAn information table of dot1dStaticTable by VLAN units. SEQUENCE OF AxsVBStaticEntry .1.3.6.1.4.1.21839.2.2.1.6.1.5.1 |
axsVBStaticEntryA configuration entry of axsVBStaticTable. AxsVBStaticEntry .1.3.6.1.4.1.21839.2.2.1.6.1.5.1.1 |
axsVBStaticIndexVLAN ID.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.5.1.1.1 |
axsVBStaticAddressMAC address of eather unicast, group or broadcast.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.6.1.5.1.1.2 |
axsVBStaticReceivePortReception port number which is applied the entry.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.1.5.1.1.3 |
axsVBStaticAllowedToGoToBit map of port indicating destination port when transfering
frame whose destination is MAC address kept by this entryro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.6.1.5.1.1.4 |
axsVBStaticStatusStatus of the entry.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.6.1.5.1.1.5 |
axsVlanBridgeMaxVlansMaximum value of VLAN ID of this device.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.101 |
axsVlanBridgeMaxSpansMaximum value of VLAN ID of VLAN which may operate
spanning tree in this device.ro VlanIndex .1.3.6.1.4.1.21839.2.2.1.6.1.102 |
axsVlanTagTranslation OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.6.10 |
axsVlanTagTranslationTableThe information table about a Tag conversion function SEQUENCE OF AxsVlanTagTranslationEntry .1.3.6.1.4.1.21839.2.2.1.6.10.1 |
axsVlanTagTranslationEntryThe entry of the information table about a Tag conversion function AxsVlanTagTranslationEntry .1.3.6.1.4.1.21839.2.2.1.6.10.1.1 |
axsVlanTagTranslationVlanIdVLAN ID which has set up the Tag conversion functionro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.10.1.1.1 |
axsVlanTagTranslationTranslatedIdTranslated ID set up by the Tag conversion functionro INTEGER .1.3.6.1.4.1.21839.2.2.1.6.10.1.1.2 |
axsVlanTagTranslationPortsThe port list which has set up the same Translated ID by the same VLAN by the Tag conversion functionro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.21839.2.2.1.6.10.1.1.3 |
axsOadp OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.7 |
axsOadpMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.7.1 |
axsOadpGlobalInfo OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.7.1.1 |
axsOadpGlobalActiveOperation status of OADP function. Status set
by enable or disable in Oadp configuration.
enable : 1
disable: 2ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.1.1 |
axsOadpGlobalCdpActiveOperation status of CDP reception function.
Status whether cdp-listener is set or not in oadp configuration.
cdp-listener : 1
cdp-listener is not set: 2ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.1.2 |
axsOadpGlobalMessageIntervalSending interval of OADP frame. The value of interval-time in oadp configuration.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.7.1.1.3 |
axsOadpGlobalHoldTimeNeighbor divice's holding time of OADP frame which this device send.
The value of hold-time in oadp configuration.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.7.1.1.4 |
axsOadpGlobalCacheLastChangeValue of sysUpTime which is set when axsOadpNeighborTable is updated.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.1.7.1.1.5 |
axsOadpGlobalNameDevice identifier.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.1.6 |
axsOadpGlobalNameTypeKind of axsOadpGlobalName.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.7.1.1.7 |
axsOadpPortInfo OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.7.1.2 |
axsOadpPortConfigTableA table of OADP port information. SEQUENCE OF AxsOadpPortConfigEntry .1.3.6.1.4.1.21839.2.2.1.7.1.2.1 |
axsOadpPortConfigEntryAn entry of OADP port information. AxsOadpPortConfigEntry .1.3.6.1.4.1.21839.2.2.1.7.1.2.1.1 |
axsOadpPortConfigIfIndexPort identification index. The same value as ifIndex.
This is only for physical ports and LA ports which are given
ifIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.1.7.1.2.1.1.1 |
axsOadpPortConfigActiveStatus of specified port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.2.1.1.2 |
axsOadpNeighborInfo OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.7.1.3 |
axsOadpNeighborTableA table of OADP neighbor nodes. SEQUENCE OF AxsOadpNeighborEntry .1.3.6.1.4.1.21839.2.2.1.7.1.3.1 |
axsOadpNeighborEntryAn entry of OADP neighbor nodes. AxsOadpNeighborEntry .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1 |
axsOadpIfIndexifIndex of reception interface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.1 |
axsOadpTagIDTag ID of IEEE802.1Q which is attached MAC frame.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.2 |
axsOadpNeighborIndexUnique numeric which identifies neighbor nodesro INTEGER .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.3 |
axsOadpNeighborTagIDValue set at TagID TLV in OADP PDU which is sent from neighbor node.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.4 |
axsOadpNeighborVendorTypeProtocol type used to find to neighbor nodes.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.5 |
axsOadpNeighborSNMPAgentAddressTypeA kind of agent address to get information by SNMP.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.6 |
axsOadpNeighborSNMPAgentAddressDisplayString formed information of agent address to get information by SNMP.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.7 |
axsOadpNeighborDescrString of sysDescr of neighbor node.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.8 |
axsOadpNeighborDeviceIDNeighbor node's device identifier.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.9 |
axsOadpNeighborSlotPortUnique string which identifies neighbor's sending interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.10 |
axsOadpNeighborIfIndexifIndex of sending interface of neighbor node.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.11 |
axsOadpNeighborIfSpeedifSpeed of sending interface of neighbor node.ro Gauge .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.12 |
axsOadpNeighborDeviceTypeDevice name of neighbor node.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.13 |
axsOadpNeighborServiceFunctions neighbor node can offer.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.14 |
axsOadpNeighborVTPMgmtDomainVTP Management Domain of sending interface of neighbor node.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.15 |
axsOadpNeighborNativeVLANNative VLAN number of sending interface of neighbor node.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.16 |
axsOadpNeighborDuplexDuplex information of sending interface of neighbor node.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.17 |
axsOadpNeighborApplianceIDAppliance ID of neighbor node.ro Gauge .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.18 |
axsOadpNeighborVlanIDVLAN ID for VoIP of neighbor node.ro Gauge .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.19 |
axsOadpNeighborPowerConsumptionElectric power comsumption of neighbor node.ro Gauge .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.20 |
axsOadpNeighborMTUMTU of sending interface of neighbor node.ro Gauge .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.21 |
axsOadpNeighborSysNamesysName of neighbor node.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.22 |
axsOadpNeighborSysObjectIDsysObjectID of neighbor node.ro OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.23 |
axsOadpNeighborSecondarySNMPAgentAddressTypeA kind of agent secondary address to get information by SNMP.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.24 |
axsOadpNeighborSecondarySNMPAgentAddressDisplayString formed information of agent secondary address to get information by SNMP.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.25 |
axsOadpNeighborPhysLocationsysLocation of neighbor node.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.26 |
axsOadpNeighborCacheLastChangeValue of sysUpTime which is set when axsOadpNeighborEntry about neighbor node is updated.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.27 |
axsOadpNeighborIfHighSpeedifHighSpeed of sending interface of neighbor node.ro Gauge .1.3.6.1.4.1.21839.2.2.1.7.1.3.1.1.28 |
axsOadpMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.7.2 |
axsOadpNeighborCachelastChangeTrapThis trap indicates that information of OADP neighbor nodes is updated. TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.7.2.0.1 |
axsFlow OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.8 |
axsAccessFilterStats OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.8.9 |
axsAccessFilterStatsInTableTable information on corresponding number of packets to flow detection condition
and operation information set by access list. SEQUENCE OF AxsAccessFilterStatsInEntry .1.3.6.1.4.1.21839.2.2.1.8.9.1 |
axsAccessFilterStatsInEntryEntry concerning corresponding number of packets to flow detection condition and
operation information set by access list. AxsAccessFilterStatsInEntry .1.3.6.1.4.1.21839.2.2.1.8.9.1.1 |
axsAccessFilterStatsInifIndexIndex value in which entry of this table is identified. INTEGER .1.3.6.1.4.1.21839.2.2.1.8.9.1.1.1 |
axsAccessFilterStatsInifIndexTypeIndicates interface type. Physical port number : 1 Interface name : 2 INTEGER .1.3.6.1.4.1.21839.2.2.1.8.9.1.1.2 |
axsAccessFilterStatsInListIndexIndex value of access list that identifies entry of this table. Unsigned32 .1.3.6.1.4.1.21839.2.2.1.8.9.1.1.3 |
axsAccessFilterStatsInSequenceNumberSequence number of flow detection condition and operation information set to access list
number or access list name. Unsigned32 .1.3.6.1.4.1.21839.2.2.1.8.9.1.1.4 |
axsAccessFilterStatsInListNameAccess list number or access list name corresponding to index of access list.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.8.9.1.1.5 |
axsAccessFilterStatsInMatchedPacketsCorresponding number of packets to flow detection condition of access list.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.8.9.1.1.6 |
axsAccessFilterStatsOutTableTable information on corresponding number of packets to flow detection condition
and operation information set by access list of Outbound. SEQUENCE OF AxsAccessFilterStatsOutEntry .1.3.6.1.4.1.21839.2.2.1.8.9.2 |
axsAccessFilterStatsOutEntryEntry concerning corresponding number of packets to flow detection condition and
operation information set by access list of Outbound. AxsAccessFilterStatsOutEntry .1.3.6.1.4.1.21839.2.2.1.8.9.2.1 |
axsAccessFilterStatsOutifIndexIndex value in which entry of this table is identified. INTEGER .1.3.6.1.4.1.21839.2.2.1.8.9.2.1.1 |
axsAccessFilterStatsOutifIndexTypeIndicates interface type. Physical port number : 1 Interface name : 2 INTEGER .1.3.6.1.4.1.21839.2.2.1.8.9.2.1.2 |
axsAccessFilterStatsOutListIndexIndex value of access list that identifies entry of this table. Unsigned32 .1.3.6.1.4.1.21839.2.2.1.8.9.2.1.3 |
axsAccessFilterStatsOutSequenceNumberSequence number of flow detection condition and operation information set to access list
number or access list name. Unsigned32 .1.3.6.1.4.1.21839.2.2.1.8.9.2.1.4 |
axsAccessFilterStatsOutListNameAccess list number or access list name corresponding to index of access list.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.8.9.2.1.5 |
axsAccessFilterStatsOutMatchedPacketsCorresponding number of packets to flow detection condition of access list.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.8.9.2.1.6 |
axsQosFlowStats OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.8.11 |
axsQosFlowStatsInTableTable information on corresponding number of packets to QoS flow detection condition
and operation information set in QoS flow list. SEQUENCE OF AxsQosFlowStatsInEntry .1.3.6.1.4.1.21839.2.2.1.8.11.1 |
axsQosFlowStatsInEntryEntry concerning corresponding number of packets to QoS flow detection condition
and operation information set in QoS Flower shop. AxsQosFlowStatsInEntry .1.3.6.1.4.1.21839.2.2.1.8.11.1.1 |
axsQosFlowStatsInifIndexIndex value in which entry of this table is identified. INTEGER .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.1 |
axsQosFlowStatsInifIndexTypeIndicates interface type. Physical port number : 1 Interface name : 2 INTEGER .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.2 |
axsQosFlowStatsInListIndexIndex value of QoS Flow list where entry of this table is identified. Unsigned32 .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.3 |
axsQosFlowStatsInSequenceNumberSequence number of flow detection condition and operation information set to QoS
flow list name. Unsigned32 .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.4 |
axsQosFlowStatsInListNameQoS flow list name corresponding to index of QoS flow list.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.5 |
axsQosFlowStatsInMatchedPacketsCorresponding number of packets to flow detection condition of QoS flow list.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.6 |
axsQosFlowStatsInMatchedPacketsMinUnderNumber of packets in which it agrees to flow detection condition of QoS flow
list and the lowest band watch is observed.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.7 |
axsQosFlowStatsInMatchedPacketsMinOverNumber of packets in which it agrees to flow detection condition of QoS flow
list and it violates the lowest band watch.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.8 |
axsQosFlowStatsInMatchedPacketsMaxUnderNumber of packets in which it agrees to flow detection condition of QoS flow
list and the maximum band control is observed.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.9 |
axsQosFlowStatsInMatchedPacketsMaxOverNumber of packets in which it agrees to flow detection condition of QoS flow
list and it violates the maximum band control.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.8.11.1.1.10 |
axsL2ld OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.10 |
axsL2ldGlobalInfo OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.10.1 |
axsL2ldVersionThe version of L2 loop detection.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.1 |
axsL2ldLoopDetectionIdL2 loop detection ID.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.2 |
axsL2ldIntervalTimeSending interval of L2 loop detection frame.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.3 |
axsL2ldOutputRateSending rate of L2 loop detection frame.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.4 |
axsL2ldThresholdDetection counts until port is put into state of inactive.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.5 |
axsL2ldHoldTimeHold time of detection counts.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.6 |
axsL2ldAutoRestoreTimeTime until port put into state of inactive is put into state of
active by automatic operation.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.7 |
axsL2ldConfigurationVlanPortCountsThe number of VLAN ports set to send L2 loop detection frame.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.8 |
axsL2ldCapacityVlanPortCountsThe number of VLAN ports that can be sent by L2 loop detection
frame sending rate.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.1.9 |
axsL2ldPortTableThe table containing port information on L2 loop detection. SEQUENCE OF AxsL2ldPortEntry .1.3.6.1.4.1.21839.2.2.1.10.2 |
axsL2ldPortEntryThe entry of port information on L2 loop detection. AxsL2ldPortEntry .1.3.6.1.4.1.21839.2.2.1.10.2.1 |
axsL2ldPortIndexIndex of L2 loop detection port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.1 |
axsL2ldPortIfIndexifIndex of L2 loop detection port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.2 |
axsL2ldPortStatusState of L2 loop detection port.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.10.2.1.3 |
axsL2ldPortTypeType of L2 loop detection port.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.10.2.1.4 |
axsL2ldPortDetectCountThe number of L2 loop detection. The number in which
L2 loop detection frame is received in hold time.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.5 |
axsL2ldPortAutoRestoringTimerTime until restoring it automatically. The value is 0
when port is active.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.6 |
axsL2ldPortSourcePortIfindexifIndex of port transmitted when L2 loop detection frame
was received at the end.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.7 |
axsL2ldPortDestinationPortIfindexifIndex of port where L2 loop detection frame was
received at the end.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.8 |
axsL2ldPortSourceVlanVLAN ID when transmitting when L2 loop detection frame
was received at the end.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.9 |
axsL2ldPortHCInFramesNumber of receptions of L2 loop detection frames.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.10.2.1.10 |
axsL2ldPortHCOutFramesNumber of transmissions of L2 loop detection frames.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.10.2.1.11 |
axsL2ldPortHCInDiscardsNumber of receptions of L2 loop detection discard frames.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.10.2.1.12 |
axsL2ldPortInactiveCountThe number of put into state of inactive.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.10.2.1.13 |
axsL2ldPortLastInactiveTimeTime put into state of inactive at the end.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.10.2.1.14 |
axsL2ldPortLastInFramesTimeTime to have received L2 loop detection frame at the end.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.10.2.1.15 |
axsOspf OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.14 |
axsOspfGeneralTableThe table of OSPF information. SEQUENCE OF AxsOspfGeneralEntry .1.3.6.1.4.1.21839.2.2.1.14.1 |
axsOspfGeneralEntryThe entry of OSPF information. AxsOspfGeneralEntry .1.3.6.1.4.1.21839.2.2.1.14.1.1 |
axsOspfGeneralDomainNumberDomain number in the Autonomous System.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.1.1.1 |
axsOspfRouterIdA integer uniquely identifying the router
in the Autonomous System.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.1.1.2 |
axsOspfAdminStatThe administrative status of OSPF in the
router.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.1.1.3 |
axsOspfVersionNumberThe current version number of the OSPF
protocol is 2.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.1.1.4 |
axsOspfAreaBdrRtrStatusA flag to note whether this router is an area
border router.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.1.1.5 |
axsOspfASBdrRtrStatusA flag to note whether this router is configured
as an Autonomous System border router.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.1.1.6 |
axsOspfExternLsaCountThe number of external (LS type 5) link-state
advertisements in the link-state database.ro Gauge .1.3.6.1.4.1.21839.2.2.1.14.1.1.7 |
axsOspfExternLsaCksumSumThe 32-bit unsigned sum of the LS checksums of
the external link-state advertisements contained
in the link-state database.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.1.1.8 |
axsOspfTOSSupportThe router's support for type-of-service routing.
This value of false(2).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.1.1.9 |
axsOspfOriginateNewLsasThe number of new link-state advertisements
that have been originated.ro Counter .1.3.6.1.4.1.21839.2.2.1.14.1.1.10 |
axsOspfRxNewLsasThe number of link-state advertisements received
determined to be new instantiations.ro Counter .1.3.6.1.4.1.21839.2.2.1.14.1.1.11 |
axsOspfExtLsdbLimitThe maximum number of non-default AS-external-LSAs
entries that can be stored in the link-state database.
If the value is -1, then there is no limit.
This value is -1ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.1.1.12 |
axsOspfMulticastExtensionsA Bit Mask indicating whether the router is
forwarding IP multicast (Class D) datagrams
based on the algorithms defined in the Multicast
Extensions to OSPF.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.1.1.13 |
axsOspfAreaTableThe router's support for demand routing. SEQUENCE OF AxsOspfAreaEntry .1.3.6.1.4.1.21839.2.2.1.14.2 |
axsOspfAreaEntryThis entry contain ospf area information. AxsOspfAreaEntry .1.3.6.1.4.1.21839.2.2.1.14.2.1 |
axsOspfAreaDomainNumberAn uniquely identifying number of domain.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.2.1.1 |
axsOspfAreaIdA 32-bit integer uniquely identifying an area.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.2.1.2 |
axsOspfAuthTypeThe authentication type specified for an area.ro INTEGER -- none(0), -- simplePassword (1), -- md5(2) .1.3.6.1.4.1.21839.2.2.1.14.2.1.3 |
axsOspfImportAsExternThe area's support for importing AS external
link- state advertisements.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.2.1.4 |
axsOspfSpfRunsThe number of times that the intra-area route
table has been calculated using this area's
link-state database.ro Counter .1.3.6.1.4.1.21839.2.2.1.14.2.1.5 |
axsOspfAreaBdrRtrCountThe total number of area border routers reachable
within this area.ro Gauge .1.3.6.1.4.1.21839.2.2.1.14.2.1.6 |
axsOspfAsBdrRtrCountThe total number of AS area border routers reachable
within this area.ro Gauge .1.3.6.1.4.1.21839.2.2.1.14.2.1.7 |
axsOspfAreaLsaCountThe total number of LSA(link-state advertisements)
in this area. Excluding AS External LSA'sro Gauge .1.3.6.1.4.1.21839.2.2.1.14.2.1.8 |
axsOspfAreaLsaCksumSumThe sum of LSA's LS checksums contained in this
area's link-state database.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.2.1.9 |
axsOspfAreaSummaryhe variable axsOspfAreaSummary controls the import
of summary LSAs into stub areas. Value is only
sendAreaSummary(2).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.2.1.10 |
axsOspfAreaStatusThis variable displays the status of the entry.
Value is only valid(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.2.1.11 |
axsOspfStubAreaTableThe set of metrics that will be advertised by
a default Area Border Router into a stub area. SEQUENCE OF AxsOspfStubAreaEntry .1.3.6.1.4.1.21839.2.2.1.14.3 |
axsOspfStubAreaEntryThe metric for a given Type of Service that
will be advertised by a default Area Border Router
into a stub area. AxsOspfStubAreaEntry .1.3.6.1.4.1.21839.2.2.1.14.3.1 |
axsOspfStubDomainNumberThe domain identifier for the Stub Area.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.3.1.1 |
axsOspfStubAreaIdThe identifier for the Stub Area.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.3.1.2 |
axsOspfStubTOSThe Type of Service associated with the metric.
Value is only 0.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.3.1.3 |
axsOspfStubMetricThe metric value applied at the indicated type
of service.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.3.1.4 |
axsOspfStubStatusThis variable displays the status of the entry.
This value is only valid(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.3.1.5 |
axsOspfStubMetricTypehis variable displays the type of metric advertised
as a default route.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.3.1.6 |
axsOspfLsdbTableThe OSPF Process's Link State Database. SEQUENCE OF AxsOspfLsdbEntry .1.3.6.1.4.1.21839.2.2.1.14.4 |
axsOspfLsdbEntryA single Link State Advertisement. AxsOspfLsdbEntry .1.3.6.1.4.1.21839.2.2.1.14.4.1 |
axsOspfLsdbDomainNumberThe identifier of the domain from which
the LSA was received.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.4.1.1 |
axsOspfLsdbAreaIdThe 32 bit identifier of the Area from which
the LSA was received.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.4.1.2 |
axsOspfLsdbTypeThe type of the link state advertisement.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.4.1.3 |
axsOspfLsdbLsidThe Link State ID . It identifies the piece of the routing
domain that is being described by the advertisement.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.4.1.4 |
axsOspfLsdbRouterIdThe number that uniquely identifies the originating
router in the Autonomous System.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.4.1.5 |
axsOspfLsdbSequenceThe sequence number field is a signed 32-bit
integer.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.4.1.6 |
axsOspfLsdbAgeThis the age of the link state adver-
tisement in seconds.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.4.1.7 |
axsOspfLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.4.1.8 |
axsOspfLsdbAdvertisementThe entire Link State Advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.14.4.1.9 |
axsOspfAreaRangeTableA range if IP addresses specified by an IP
address/IP network mask pair. SEQUENCE OF AxsOspfAreaRangeEntry .1.3.6.1.4.1.21839.2.2.1.14.5 |
axsOspfAreaRangeEntryA range if IP addresses specified by an IP
address/IP network mask pair. AxsOspfAreaRangeEntry .1.3.6.1.4.1.21839.2.2.1.14.5.1 |
axsOspfAreaRangeDomainNumberDomain number of the Area.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.5.1.1 |
axsOspfAreaRangeAreaIdThe Area the Address Range is to be found
within.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.5.1.2 |
axsOspfAreaRangeNetThe IP Address of the Net or Subnet indicated
by the range.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.5.1.3 |
axsOspfAreaRangeMaskThe Subnet Mask that pertains to the Net or
Subnet.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.5.1.4 |
axsOspfAreaRangeStatusThis variable displays the status of the entry.
This value is only valid(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.5.1.5 |
axsOspfAreaRangeEffectSubnets subsumed by ranges either trigger the
advertisement of the indicated summary (adver-
tiseMatching), or result in the subnet's not
being advertised at all outside the area.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.5.1.6 |
axsOspfIfTableThe OSPF Interface Table describes the interfaces
from the viewpoint of OSPF. SEQUENCE OF AxsOspfIfEntry .1.3.6.1.4.1.21839.2.2.1.14.7 |
axsOspfIfEntryThe OSPF Interface Entry describes one interface
from the viewpoint of OSPF. AxsOspfIfEntry .1.3.6.1.4.1.21839.2.2.1.14.7.1 |
axsOspfIfDomainNumberThe domain number of this OSPF interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.1 |
axsOspfIfIpAddressThe IP address of this OSPF interface.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.7.1.2 |
axsOspfAddressLessIfFor the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP Addresses, and the corresponding value of
ifIndex for interfaces having no IP Address.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.3 |
axsOspfIfAreaIdA integer uniquely identifying the area to which
the interface connects.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.7.1.4 |
axsOspfIfTypeThe OSPF interface type.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.7.1.5 |
axsOspfIfAdminStatThe OSPF interface's administrative status.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.7.1.6 |
axsOspfIfRtrPriorityThe priority of this interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.7 |
axsOspfIfTransitDelayThe estimated number of seconds it takes to
transmit a link state update packet over this
interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.8 |
axsOspfIfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.9 |
axsOspfIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.10 |
axsOspfIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neighbors
declare the router down.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.11 |
axsOspfIfPollIntervalThe larger time interval, in seconds, between
the Hello packets sent to an inactive non-
broadcast multi- access neighbor.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.7.1.12 |
axsOspfIfStateThe OSPF Interface State.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.7.1.13 |
axsOspfIfDesignatedRouterThe IP Address of the Designated Router.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.7.1.14 |
axsOspfIfBackupDesignatedRouterThe IP Address of the Backup Designated Router.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.7.1.15 |
axsOspfIfEventsThe number of times this OSPF interface has
changed its state, or an error has occurred.ro Counter .1.3.6.1.4.1.21839.2.2.1.14.7.1.16 |
axsOspfIfAuthKeyThe Authentication Key.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.14.7.1.17 |
axsOspfIfStatusThis variable displays the status of the entry.
this value is only valid(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.7.1.18 |
axsOspfIfMulticastForwardingThe way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link unicasts.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.7.1.19 |
axsOspfIfMetricTableThe TOS metrics for a non-virtual interface identified
by the interface index. SEQUENCE OF AxsOspfIfMetricEntry .1.3.6.1.4.1.21839.2.2.1.14.8 |
axsOspfIfMetricEntryA particular TOS metric for a non-virtual interface
identified by the interface index. AxsOspfIfMetricEntry .1.3.6.1.4.1.21839.2.2.1.14.8.1 |
axsOspfIfMetricDomainNumberThe domain number of this OSPF interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.8.1.1 |
axsOspfIfMetricIpAddressThe IP address of this OSPF interface.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.8.1.2 |
axsOspfIfMetricAddressLessIfFor the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP Addresses, and the value of ifIndex for in-
terfaces having no IP Address.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.8.1.3 |
axsOspfIfMetricTOSThe type of service metric being referenced.
this value is only 0.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.8.1.4 |
axsOspfIfMetricValueThe metric of using this type of service on
this interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.8.1.5 |
axsOspfIfMetricStatusThis variable displays the status of the entry.
This entry status is only valid(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.8.1.6 |
axsOspfVirtIfTableInformation about this router's virtual interfaces. SEQUENCE OF AxsOspfVirtIfEntry .1.3.6.1.4.1.21839.2.2.1.14.9 |
axsOspfVirtIfEntryInformation about a single Virtual Interface. AxsOspfVirtIfEntry .1.3.6.1.4.1.21839.2.2.1.14.9.1 |
axsOspfVirtIfDomainNumberThe domain number for this Virtual Interfacero INTEGER .1.3.6.1.4.1.21839.2.2.1.14.9.1.1 |
axsOspfVirtIfAreaIdThe Transit Area that the Virtual Link traverses.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.9.1.2 |
axsOspfVirtIfNeighborThe Router ID of the Virtual Neighbor.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.9.1.3 |
axsOspfVirtIfTransitDelayThe estimated number of seconds it takes to
transmit a link- state update packet over this
interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.9.1.4 |
axsOspfVirtIfRetransIntervalThe number of seconds between link-state advertisement
retransmissions, for adjacencies belonging to this
interface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.9.1.5 |
axsOspfVirtIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the in-
terface.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.9.1.6 |
axsOspfVirtIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neighbors
declare the router down.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.9.1.7 |
axsOspfVirtIfStateOSPF virtual interface states.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.9.1.8 |
axsOspfVirtIfEventsThe number of state changes or error events on
this Virtual Linkro Counter .1.3.6.1.4.1.21839.2.2.1.14.9.1.9 |
axsOspfVirtIfAuthKeyAuthentication key of this interface.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.14.9.1.10 |
axsOspfVirtIfStatusThis variable displays the status of the entry.
This entry is only valid(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.9.1.11 |
axsOspfNbrTableA table of non-virtual neighbor information. SEQUENCE OF AxsOspfNbrEntry .1.3.6.1.4.1.21839.2.2.1.14.10 |
axsOspfNbrEntryThe information regarding a single neighbor. AxsOspfNbrEntry .1.3.6.1.4.1.21839.2.2.1.14.10.1 |
axsOspfNbrDomainNumberOSPF domain number of this neighbor.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.10.1.1 |
axsOspfNbrIpAddrThe IP address this neighbor is using in its
IP Source Address.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.10.1.2 |
axsOspfNbrAddressLessIndexOn an interface having an IP Address, zero.
On addressless interfaces, the corresponding
value of ifIndex in the Internet Standard MIB.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.10.1.3 |
axsOspfNbrRtrIdThe integer uniquely identifying the neighboring
router in the Autonomous System.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.10.1.4 |
axsOspfNbrOptionsA Bit Mask corresponding to the neighbor's op-
tions field.
Bit 0, if set, indicates that the system will
operate on Type of Service metrics other than
TOS 0. If zero, the neighbor will ignore all
metrics except the TOS 0 metric.
Bit 1, if set, indicates that the associated
area accepts and operates on external informa-
tion; if zero, it is a stub area.
Bit 2, if set, indicates that the system is ca-
pable of routing IP Multicast datagrams; i.e.,
that it implements the Multicast Extensions to
OSPF.
Bit 3, if set, indicates that the associated
area is an NSSA. These areas are capable of
carrying type 7 external advertisements, which
are translated into type 5 external advertise-
ments at NSSA borders.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.10.1.5 |
axsOspfNbrPriorityThe priority of this neighbor.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.10.1.6 |
axsOspfNbrStateThe State of the relationship with this Neighbor.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.10.1.7 |
axsOspfNbrEventsThe number of times this neighbor relationship
has changed state, or an error has occurred.ro Counter .1.3.6.1.4.1.21839.2.2.1.14.10.1.8 |
axsOspfNbrLsRetransQLenThe current length of the retransmission queue.ro Gauge .1.3.6.1.4.1.21839.2.2.1.14.10.1.9 |
axsOspfNbmaNbrStatusThis variable displays the status of the entry.
This entry value is only valid(1). And enable to response
this entry when axsOspfIfType is nbma.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.10.1.10 |
axsOspfNbmaNbrPermanenceThis variable displays the status of the entry.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.10.1.11 |
axsOspfVirtNbrTableA table of virtual neighbor information. SEQUENCE OF AxsOspfVirtNbrEntry .1.3.6.1.4.1.21839.2.2.1.14.11 |
axsOspfVirtNbrEntryVirtual neighbor information. AxsOspfVirtNbrEntry .1.3.6.1.4.1.21839.2.2.1.14.11.1 |
axsOspfVirtNbrDomainNumberThe domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.11.1.1 |
axsOspfVirtNbrAreaThe Transit Area Identifier.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.11.1.2 |
axsOspfVirtNbrRtrIdA integer uniquely identifying the neighboring
router in the Autonomous System.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.11.1.3 |
axsOspfVirtNbrIpAddrThe IP address this Virtual Neighbor is using.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.11.1.4 |
axsOspfVirtNbrOptionsA Bit Mask corresponding to the neighbor's options
field.
Bit 1, if set, indicates that the system will operate
on Type of Service metrics other than TOS 0. If zero,
the neighbor will ignore all metrics except the TOS
0 metric.
Bit 2, if set, indicates that the system is Network
Multicast capable; ie, that it implements OSPF Multicast
Routing.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.11.1.5 |
axsOspfVirtNbrStateThe state of the Virtual Neighbor Relationship.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.11.1.6 |
axsOspfVirtNbrEventsThe number of times this virtual link has changed
its state, or an error has occurred.ro Counter .1.3.6.1.4.1.21839.2.2.1.14.11.1.7 |
axsOspfVirtNbrLsRetransQLenThe current length of the retransmission queue.ro Gauge .1.3.6.1.4.1.21839.2.2.1.14.11.1.8 |
axsOspfExtLsdbTableThe OSPF Process's Links State Database. SEQUENCE OF AxsOspfExtLsdbEntry .1.3.6.1.4.1.21839.2.2.1.14.12 |
axsOspfExtLsdbEntryA single Link State Advertisement. AxsOspfExtLsdbEntry .1.3.6.1.4.1.21839.2.2.1.14.12.1 |
axsOspfExtLsdbDomainNumberOSPF domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.12.1.1 |
axsOspfExtLsdbTypeThe type of the link state advertisement.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.12.1.2 |
axsOspfExtLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.12.1.3 |
axsOspfExtLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.12.1.4 |
axsOspfExtLsdbSequenceThe sequence number field is a signed 32-bit integer.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.12.1.5 |
axsOspfExtLsdbAgeThe age of the link state advertisement in seconds.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.12.1.6 |
axsOspfExtLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.12.1.7 |
axsOspfExtLsdbAdvertisementThe entire Link State Advertisement, including its header.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.14.12.1.8 |
axsOspfAreaAggregateTableA range of IP addresses specified by an IP
address/IP network mask pair. SEQUENCE OF AxsOspfAreaAggregateEntry .1.3.6.1.4.1.21839.2.2.1.14.14 |
axsOspfAreaAggregateEntryA range of IP addresses specified by an IP
address/IP network mask pair. AxsOspfAreaAggregateEntry .1.3.6.1.4.1.21839.2.2.1.14.14.1 |
axsOspfAreaAggregateDomainNumberOSPF domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.14.1.1 |
axsOspfAreaAggregateAreaIDThe Area the Address Aggregate is to be found within.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.14.1.2 |
axsOspfAreaAggregateLsdbTypeThe type of the Address Aggregate. This field
specifies the Lsdb type that this Address
Aggregate applies to.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.14.1.3 |
axsOspfAreaAggregateNetThe IP Address of the Net or Subnet indicated by the range.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.14.1.4 |
axsOspfAreaAggregateMaskThe Subnet Mask that pertains to the Net or Subnet.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.14.1.5 |
axsOspfAreaAggregateStatusThis variable displays the status of the entry.
This entry value is only valid(1).ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.14.1.6 |
axsOspfAreaAggregateEffectSubnets subsumed by ranges either trigger the
advertisement of the indicated aggregate (ad-
vertiseMatching), or result in the subnet's not
being advertised at all outside the area.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.14.1.7 |
axsOspfTrap OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.14.16 |
axsOspfTrapControlTableThe table about trap information. SEQUENCE OF AxsOspfTrapControlEntry .1.3.6.1.4.1.21839.2.2.1.14.16.1 |
axsOspfTrapControlEntryThe Entry about trap information. AxsOspfTrapControlEntry .1.3.6.1.4.1.21839.2.2.1.14.16.1.1 |
axsOspfTrapDomainNumberaxsOspfTrap domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.14.16.1.1.1 |
axsOspfSetTrapA four-octet string serving as a bit map for
the trap events defined by the OSPF traps. This
object is used to enable and disable specific
OSPF traps where a 1 in the bit field
represents enabled. The right-most bit (least
significant) represents trap 0.rw OCTET STRING .1.3.6.1.4.1.21839.2.2.1.14.16.1.1.2 |
axsOspfConfigErrorTypePotential types of configuration conflicts.
Used by the ospfConfigError and ospfConfigVir-
tError traps.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.16.1.1.3 |
axsOspfPacketTypeOSPF packet types.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.14.16.1.1.4 |
axsOspfPacketSrcThe IP address of an inbound packet that can-
not be identified by a neighbor instance.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.14.16.1.1.5 |
axsOspfTraps OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.14.16.2 |
axsOspfVirtIfStateChangeAn axsOspfIfStateChange trap signifies that there has been a change
in the state of an OSPF virtual interface. TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.1 |
axsOspfNbrStateChangeAn axsOspfNbrStateChange trap signifies that
there has been a change in the state of a non-
virtual OSPF neighbor. This trap should be
generated when the neighbor state regresses
(e.g., goes from Attempt or Full to 1-Way or
Down) or progresses to a terminal state (e.g.,
2-Way or Full). When an neighbor transitions
from or to Full on non-broadcast multi-access
and broadcast networks, the trap should be gen-
erated by the designated router. A designated
router transitioning to Down will be noted by
axsOspfIfStateChange. TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.2 |
axsOspfVirtNbrStateChangeAn axsOspfIfStateChange trap signifies that there
has been a change in the state of an OSPF vir-
tual neighbor. This trap should be generated
when the neighbor state regresses (e.g., goes
from Attempt or Full to 1-Way or Down) or
progresses to a terminal state (e.g., Full). TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.3 |
axsOspfIfConfigErrorAn axsOspfIfConfigError trap signifies that a
packet has been received on a non-virtual in-
terface from a router whose configuration
parameters conflict with this router's confi-
guration parameters. Note that the event op-
tionMismatch should cause a trap only if it
prevents an adjacency from forming. TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.4 |
axsOspfVirtIfConfigErrorAn axsOspfConfigError trap signifies that a pack-
et has been received on a virtual interface
from a router whose configuration parameters
conflict with this router's configuration
parameters. Note that the event optionMismatch
should cause a trap only if it prevents an ad-
jacency from forming. TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.5 |
axsOspfIfAuthFailureAn axsOspfIfAuthFailure trap signifies that a
packet has been received on a non-virtual in-
terface from a router whose authentication key
or authentication type conflicts with this
router's authentication key or authentication
type. TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.6 |
axsOspfVirtIfAuthFailureAn axsOspfVirtIfAuthFailure trap signifies that a
packet has been received on a virtual interface
from a router whose authentication key or au-
thentication type conflicts with this router's
authentication key or authentication type. TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.7 |
axsOspfIfStateChangeAn axsOspfIfStateChange trap signifies that there
has been a change in the state of a non-virtual
OSPF interface. This trap should be generated
when the interface state regresses (e.g., goes
from Dr to Down) or progresses to a terminal
state (i.e., Point-to-Point, DR Other, Dr, or
Backup). TRAP-TYPE .1.3.6.1.4.1.21839.2.2.1.14.16.2.0.16 |
axsOspfv3 OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.15 |
axsOspfv3GeneralTableThe table which ospfv3 information is stored in. SEQUENCE OF AxsOspfv3GeneralEntry .1.3.6.1.4.1.21839.2.2.1.15.1 |
axsOspfv3GeneralEntryThe list of the ospfv3 information. AxsOspfv3GeneralEntry .1.3.6.1.4.1.21839.2.2.1.15.1.1 |
axsOspfv3GeneralDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.1.1.1 |
axsOspfv3RouterIdA 32-bit integer uniquely identifying the
router in the Autonomous System.
By convention, to ensure uniqueness, this
should default to the value of one of the
router's IPv4 interface addresses if IPv4 is
configured.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.1.1.2 |
axsOspfv3AdminStatThe administrative status of axsOspfv3 in the
router. The value 'enabled' denotes that the
axsOspfv3 Process is active on at least one inter-
face; 'disabled' disables it on all inter-
faces.ro Status (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.1.1.3 |
axsOspfv3VersionNumberThe version number of OSPF for IPv6 is 3.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.1.1.4 |
axsOspfv3AreaBdrRtrStatusA flag to note whether this router is an area
border router.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.1.1.5 |
axsOspfv3ASBdrRtrStatusA flag to note whether this router is config-
ured as an Autonomous System border router.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.1.1.6 |
axsOspfv3AsScopeLsaCountThe number of AS-Scope (e.g. AS-External) link-state
advertisements in the link-state database.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.1.1.7 |
axsOspfv3AsScopeLsaCksumSumThe 32-bit unsigned sum of the LS checksums of
the AS-scoped link-state advertisements con-
tained in the link-state database. This sum
can be used to determine if there has been a
change in a router's link state database, and
to compare the link-state database of two
routers.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.1.1.8 |
axsOspfv3OriginateNewLsasThe number of new link-state advertisements
that have been originated. This number is in-
cremented each time the router originates a new
LSA.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.15.1.1.9 |
axsOspfv3RxNewLsasThe number of link-state advertisements re-
ceived determined to be new instantiations.
This number does not include newer instantia-
tions of self-originated link-state advertise-
ments.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.15.1.1.10 |
axsOspfv3ExtAreaLsdbLimitThe maximum number of non-default AS-
external-LSAs entries that can be stored in the
link-state database. If the value is -1, then
there is no limit.
When the number of non-default AS-external-LSAs
in a router's link-state database reaches
axsOspfv3ExtAreaLsdbLimit, the router enters Overflow-
State. The router never holds more than
axsOspfv3ExtAreaLsdbLimit non-default AS-external-LSAs
in its database. OspfExtAreaLsdbLimit MUST be set
identically in all routers attached to the axsOspfv3
backbone and/or any regular axsOspfv3 area. (i.e.,
axsOspfv3 stub areas and NSSAs are excluded).ro Integer32 (-1..'7FFFFFFF'h) .1.3.6.1.4.1.21839.2.2.1.15.1.1.11 |
axsOspfv3MulticastExtensionsA Bit Mask indicating whether the router is
forwarding IPv6 multicast datagrams
based on the algorithms defined in the Multi-
cast Extensions to OSPF.
Bit 0, if set, indicates that the router can
forward IPv6 multicast datagrams in the router's
directly attached areas (called intra-area mul-
ticast routing).
Bit 1, if set, indicates that the router can
forward IPv6 multicast datagrams between axsOspfv3
areas (called inter-area multicast routing).
Bit 2, if set, indicates that the router can
forward IPv6 multicast datagrams between Auto-
nomous Systems (called inter-AS multicast rout-
ing).
Only certain combinations of bit settings are
allowed, namely: 0 (no multicast forwarding is
enabled), 1 (intra-area multicasting only), 3
(intra-area and inter-area multicasting), 5
(intra-area and inter-AS multicasting) and 7
(multicasting everywhere). By default, no mul-
ticast forwarding is enabled.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.1.1.12 |
axsOspfv3DemandExtensionsThe router's support for demand routing.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.1.1.14 |
axsOspfv3TrafficEngineeringSupportThe router's support for traffic engineering
extensions.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.1.1.15 |
axsOspfv3AreaTableInformation describing the configured parame-
ters and cumulative statistics of the router's
attached areas. SEQUENCE OF AxsOspfv3AreaEntry .1.3.6.1.4.1.21839.2.2.1.15.2 |
axsOspfv3AreaEntryInformation describing the configured parame-
ters and cumulative statistics of one of the
router's attached areas. AxsOspfv3AreaEntry .1.3.6.1.4.1.21839.2.2.1.15.2.1 |
axsOspfv3AreaDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.2.1.1 |
axsOspfv3AreaIdA 32-bit integer uniquely identifying an area.
Area ID 0.0.0.0 is used for the axsOspfv3 backbone.ro AreaID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.2.1.2 |
axsOspfv3ImportAsExternIndicates whether an area is a Stub area, NSSA, or
standard area. AS-scope LSAs are not imported into Stub
Areas or NSSAs. NSSAs import AS-External data as Type-7
LSAs which have Area-scopero Enumeration .1.3.6.1.4.1.21839.2.2.1.15.2.1.3 |
axsOspfv3SpfRunsThe number of times that the intra-area route
table has been calculated using this area's
link-state database. This is typically done
using Dijkstra's algorithm.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.15.2.1.4 |
axsOspfv3AreaBdrRtrCountThe total number of area border routers reach-
able within this area. This is initially zero,
and is calculated in each SPF Pass.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.2.1.5 |
axsOspfv3AsBdrRtrCountThe total number of Autonomous System border
routers reachable within this area. This is
initially zero, and is calculated in each SPF
Pass.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.2.1.6 |
axsOspfv3AreaScopeLsaCountThe total number of Area-Scope link-state
advertisements in this area's link-state
database.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.2.1.7 |
axsOspfv3AreaScopeLsaCksumSumThe 32-bit unsigned sum of the Area-Scope link-state
advertisements' LS checksums contained in this
area's link-state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link-state database of two routers.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.2.1.8 |
axsOspfv3AreaSummaryThe variable axsOspfv3AreaSummary controls the im-
port of summary LSAs into stub areas. It has
no effect on other areas.
If it is noAreaSummary, the router will neither
originate nor propagate summary LSAs into the
stub area. It will rely entirely on its de-
fault route.
If it is sendAreaSummary, the router will both
summarize and propagate summary LSAs.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.2.1.9 |
axsOspfv3AreaStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.2.1.10 |
axsOspfv3StubMetricThe metric value advertised for the default route
into Stub and NSSA areas.ro BigMetric -- .1.3.6.1.4.1.21839.2.2.1.15.2.1.11 |
axsOspfv3AsLsdbTableThe axsOspfv3 Process's AS-Scope Link State Database. SEQUENCE OF AxsOspfv3AsLsdbEntry .1.3.6.1.4.1.21839.2.2.1.15.3 |
axsOspfv3AsLsdbEntryA single AS-Scope Link State Advertisement. AxsOspfv3AsLsdbEntry .1.3.6.1.4.1.21839.2.2.1.15.3.1 |
axsOspfv3AsLsdbDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.3.1.1 |
axsOspfv3AsLsdbTypeThe type of the link state advertisement.
Each link state type has a separate advertise-
ment format. Unrecognized AS-Scope LSAs with the
U-bit set are also store in this database.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.3.1.2 |
axsOspfv3AsLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.3.1.3 |
axsOspfv3AsLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPF for IPv4, the LSID has no
addressing semantics.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.15.3.1.4 |
axsOspfv3AsLsdbSequenceThe sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.3.1.5 |
axsOspfv3AsLsdbAgeThis field is the age of the link state adver-
tisement in seconds.ro Integer32 -- Should be 0..MaxAge .1.3.6.1.4.1.21839.2.2.1.15.3.1.6 |
axsOspfv3AsLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.3.1.7 |
axsOspfv3AsLsdbAdvertisementThe entire Link State Advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.15.3.1.8 |
axsOspfv3AreaLsdbTableThe axsOspfv3 Process's Area-Scope Link State Database. SEQUENCE OF AxsOspfv3AreaLsdbEntry .1.3.6.1.4.1.21839.2.2.1.15.4 |
axsOspfv3AreaLsdbEntryA single Area-Scope Link State Advertisement. AxsOspfv3AreaLsdbEntry .1.3.6.1.4.1.21839.2.2.1.15.4.1 |
axsOspfv3AreaLsdbDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.4.1.1 |
axsOspfv3AreaLsdbAreaIdThe 32 bit identifier of the Area from which the
LSA was received.ro AreaID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.4.1.2 |
axsOspfv3AreaLsdbTypeThe type of the link state advertisement.
Each link state type has a separate advertise-
ment format. Unrecognized Area-Scope LSAs with
the U-bit set are also stored in this database.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.4.1.3 |
axsOspfv3AreaLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.4.1.4 |
axsOspfv3AreaLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPF for IPv4, the LSID has no
addressing semantics.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.15.4.1.5 |
axsOspfv3AreaLsdbSequenceThe sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.4.1.6 |
axsOspfv3AreaLsdbAgeThis field is the age of the link state adver-
tisement in seconds.ro Integer32 -- Should be 0..MaxAge .1.3.6.1.4.1.21839.2.2.1.15.4.1.7 |
axsOspfv3AreaLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.4.1.8 |
axsOspfv3AreaLsdbAdvertisementThe entire Link State Advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.15.4.1.9 |
axsOspfv3LinkLsdbTableThe axsOspfv3 Process's Link-Scope Link State Database. SEQUENCE OF AxsOspfv3LinkLsdbEntry .1.3.6.1.4.1.21839.2.2.1.15.5 |
axsOspfv3LinkLsdbEntryA single Link-Scope Link State Advertisement. AxsOspfv3LinkLsdbEntry .1.3.6.1.4.1.21839.2.2.1.15.5.1 |
axsOspfv3LinkLsdbDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.5.1.1 |
axsOspfv3LinkLsdbIfIndexThe identifier of the link from which the LSA
was received.ro Ipv6IfIndex (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.5.1.2 |
axsOspfv3LinkLsdbTypeThe type of the link state advertisement.
Each link state type has a separate advertise-
ment format. Unrecognized Link-Scope LSAs with
the U-bit set are also stored in this database.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.5.1.3 |
axsOspfv3LinkLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.5.1.4 |
axsOspfv3LinkLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPF for IPv4, the LSID has no
addressing semantics.ro IpAddress .1.3.6.1.4.1.21839.2.2.1.15.5.1.5 |
axsOspfv3LinkLsdbSequenceThe sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.5.1.6 |
axsOspfv3LinkLsdbAgeThis field is the age of the link state adver-
tisement in seconds.ro Integer32 -- Should be 0..MaxAge .1.3.6.1.4.1.21839.2.2.1.15.5.1.7 |
axsOspfv3LinkLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.5.1.8 |
axsOspfv3LinkLsdbAdvertisementThe entire Link State Advertisement, including
its header.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.15.5.1.9 |
axsOspfv3IfTableThe axsOspfv3 Interface Table describes the inter-
faces from the viewpoint of axsOspfv3. SEQUENCE OF AxsOspfv3IfEntry .1.3.6.1.4.1.21839.2.2.1.15.7 |
axsOspfv3IfEntryThe axsOspfv3 Interface Entry describes one inter-
face from the viewpoint of axsOspfv3. AxsOspfv3IfEntry .1.3.6.1.4.1.21839.2.2.1.15.7.1 |
axsOspfv3IfDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.7.1.1 |
axsOspfv3IfIndexThe interface index of this axsOspfv3 interface.
It corresponds to the interface index of the
Ipv6 interface on which axsOspfv3 is configured.ro Ipv6IfIndex (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.7.1.2 |
axsOspfv3IfAreaIdA 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0.0.0.0 is used for the axsOspfv3 backbone.ro AreaID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.3 |
axsOspfv3IfTypeThe axsOspfv3 interface type.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.7.1.4 |
axsOspfv3IfAdminStatThe axsOspfv3 interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to axsOspfv3.ro Status (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.5 |
axsOspfv3IfRtrPriorityThe priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not eligi-
ble to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker.ro DesignatedRouterPriority (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.6 |
axsOspfv3IfTransitDelayThe estimated number of seconds it takes to
transmit a link state update packet over this
interface.ro UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.7 |
axsOspfv3IfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets.ro UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.8 |
axsOspfv3IfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for all
routers attached to a common network.ro HelloRange (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.9 |
axsOspfv3IfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for all routers attached
to a common network.ro PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.10 |
axsOspfv3IfPollIntervalThe larger time interval, in seconds, between
the Hello packets sent to an inactive non-
broadcast multi- access neighbor.ro PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.11 |
axsOspfv3IfStateThe axsOspfv3 Interface State.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.7.1.12 |
axsOspfv3IfDesignatedRouterThe Router ID of the Designated Router.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.13 |
axsOspfv3IfBackupDesignatedRouterThe Router ID of the Backup Designated
Router.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.15 |
axsOspfv3IfEventsThe number of times this OSPF interface has
changed its state, or an error has occurred.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.15.7.1.16 |
axsOspfv3IfStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.7.1.18 |
axsOspfv3IfMulticastForwardingThe way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link uni-
casts. Data link multicasting is not meaning-
ful on point to point and NBMA interfaces, and
setting axsOspfv3MulticastForwarding to 0 effective-
ly disables all multicast forwarding.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.7.1.19 |
axsOspfv3IfDemandIndicates whether Demand axsOspfv3 procedures (hel-
lo supression to FULL neighbors and setting the
DoNotAge flag on proogated LSAs) should be per-
formed on this interface.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.7.1.20 |
axsOspfv3IfMetricValueThe metric assigned to this interface.
The default value of the Metric is
10^8 / ifSpeed.ro Metric (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.7.1.21 |
axsOspfv3IfLinkScopeLsaCountThe total number of Link-Scope link-state
advertisements in this link's link-state database.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.7.1.22 |
axsOspfv3IfLinkLsaCksumSumThe 32-bit unsigned sum of the Link-Scope link-state
advertisements' LS checksums contained in this
link's link-state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link-state database of two routers.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.7.1.23 |
axsOspfv3IfInstIdEnables multiple instances of axsOspfv3 to be run over
a single link. Each protocol instance would be assigned
a separate ID. This ID has local link significance
only.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.7.1.24 |
axsOspfv3VirtIfTableInformation about this router's virtual inter-
faces. SEQUENCE OF AxsOspfv3VirtIfEntry .1.3.6.1.4.1.21839.2.2.1.15.8 |
axsOspfv3VirtIfEntryInformation about a single Virtual Interface. AxsOspfv3VirtIfEntry .1.3.6.1.4.1.21839.2.2.1.15.8.1 |
axsOspfv3VirtIfDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.8.1.1 |
axsOspfv3VirtIfAreaIdThe Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0ro AreaID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.8.1.2 |
axsOspfv3VirtIfNeighborThe Router ID of the Virtual Neighbor.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.8.1.3 |
axsOspfv3VirtIfIndexThe interface index of this axsOspfv3 virtual interface.
It must be unique among all the interface indices
on the router.ro Ipv6IfIndex (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.8.1.4 |
axsOspfv3VirtIfTransitDelayThe estimated number of seconds it takes to
transmit a link- state update packet over this
interface.ro UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.8.1.5 |
axsOspfv3VirtIfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets. This
value should be well over the expected round-
trip time.ro UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.8.1.6 |
axsOspfv3VirtIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for the
virtual neighbor.ro HelloRange (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.8.1.7 |
axsOspfv3VirtIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for the virtual neigh-
bor.ro PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.8.1.8 |
axsOspfv3VirtIfStateOSPF virtual interface states.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.8.1.9 |
axsOspfv3VirtIfEventsThe number of state changes or error events on
this Virtual Linkro Counter32 .1.3.6.1.4.1.21839.2.2.1.15.8.1.10 |
axsOspfv3VirtIfStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.8.1.11 |
axsOspfv3VirtIfLinkScopeLsaCountThe total number of Link-Scope link-state
advertisements in this virtual link's link-state
database.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.8.1.12 |
axsOspfv3VirtIfLinkLsaCksumSumThe 32-bit unsigned sum of the Link-Scope link-state
advertisements' LS checksums contained in this
virtual link's link-state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link-state database of two routers.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.8.1.13 |
axsOspfv3NbrTableA table of non-virtual neighbor information. SEQUENCE OF AxsOspfv3NbrEntry .1.3.6.1.4.1.21839.2.2.1.15.9 |
axsOspfv3NbrEntryThe information regarding a single neighbor. AxsOspfv3NbrEntry .1.3.6.1.4.1.21839.2.2.1.15.9.1 |
axsOspfv3NbrDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.9.1.1 |
axsOspfv3NbrIfIndexThe local link ID of the link over which the
neighbor can be reached.ro Ipv6IfIndex (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.9.1.2 |
axsOspfv3NbrIpv6AddrThe IPv6 address of the neighbor associated with
the local link.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.9.1.3 |
axsOspfv3NbrRtrIdA 32-bit integer (represented as a type IpAd-
dress) uniquely identifying the neighboring
router in the Autonomous System.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.9.1.4 |
axsOspfv3NbrOptionsA Bit Mask corresponding to the neighbor's op-
tions field.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.9.1.5 |
axsOspfv3NbrPriorityThe priority of this neighbor in the designat-
ed router election algorithm. The value 0 sig-
nifies that the neighbor is not eligible to be-
come the designated router on this particular
network.ro DesignatedRouterPriority (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.9.1.6 |
axsOspfv3NbrStateThe State of the relationship with this Neigh-
bor.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.9.1.7 |
axsOspfv3NbrEventsThe number of times this neighbor relationship
has changed state, or an error has occurred.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.15.9.1.8 |
axsOspfv3NbrLsRetransQLenThe current length of the retransmission
queue.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.9.1.9 |
axsOspfv3NbrHelloSuppressedIndicates whether Hellos are being suppressed
to the neighborro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.9.1.12 |
axsOspfv3NbrIfIdThe interface ID that the neighbor advertises
in its Hello Packets on this link, that is, the
neighbor's local interface index.ro Ipv6IfIndex (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.9.1.13 |
axsOspfv3VirtNbrTableA table of virtual neighbor information. SEQUENCE OF AxsOspfv3VirtNbrEntry .1.3.6.1.4.1.21839.2.2.1.15.10 |
axsOspfv3VirtNbrEntryVirtual neighbor information. AxsOspfv3VirtNbrEntry .1.3.6.1.4.1.21839.2.2.1.15.10.1 |
axsOspfv3VirtNbrDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.10.1.1 |
axsOspfv3VirtNbrAreaThe Transit Area Identifier.ro AreaID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.10.1.2 |
axsOspfv3VirtNbrRtrIdA 32-bit integer uniquely identifying the
neighboring router in the Autonomous System.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.10.1.3 |
axsOspfv3VirtNbrIfIndexThe local link ID for the virtual link over
which the neighbor can be reached.ro Ipv6IfIndex (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.10.1.4 |
axsOspfv3VirtNbrIpv6AddrThe IPv6 address used to reach this Virtual Neighbor.
It must be a Site-Local or Global scope address.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.10.1.5 |
axsOspfv3VirtNbrOptionsA Bit Mask corresponding to the neighbor's op-
tions field.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.15.10.1.6 |
axsOspfv3VirtNbrStateThe state of the Virtual Neighbor Relation-
ship.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.10.1.7 |
axsOspfv3VirtNbrEventsThe number of times this virtual link has
changed its state, or an error has occurred.ro Counter32 .1.3.6.1.4.1.21839.2.2.1.15.10.1.8 |
axsOspfv3VirtNbrLsRetransQLenThe current length of the retransmission
queue.ro Gauge32 .1.3.6.1.4.1.21839.2.2.1.15.10.1.9 |
axsOspfv3VirtNbrHelloSuppressedIndicates whether Hellos are being suppressed
to the neighborro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.10.1.10 |
axsOspfv3VirtNbrIfIdThe interface ID that the neighbor advertises
in its Hello Packets on this virtual link, that is,
the neighbor's local interface index.ro Ipv6IfIndex (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.10.1.11 |
axsOspfv3AreaAggregateTableA range of IPv6 prefixes specified by a
prefix/prefix length pair. Note that if
ranges are configured such that one range sub-
sumes another range the most specific match is
the preferred one. SEQUENCE OF AxsOspfv3AreaAggregateEntry .1.3.6.1.4.1.21839.2.2.1.15.11 |
axsOspfv3AreaAggregateEntryA range of IPv6 prefixes specified by a
prefix/prefix length pair. Note that if
ranges are configured such that one range sub-
sumes another range the most specific match is
the preferred one. AxsOspfv3AreaAggregateEntry .1.3.6.1.4.1.21839.2.2.1.15.11.1 |
axsOspfv3AreaAggregateDomainNumberospfv3 domain number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.11.1.1 |
axsOspfv3AreaAggregateAreaIDThe Area the Address Aggregate is to be found
within.ro AreaID (OSPF-MIB) .1.3.6.1.4.1.21839.2.2.1.15.11.1.2 |
axsOspfv3AreaAggregateAreaLsdbTypeThe type of the Address Aggregate. This field
specifies the Area Lsdb type that this Address Ag-
gregate applies to.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.11.1.3 |
axsOspfv3AreaAggregateIndexA unique identifier for this aggregate table entry.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.15.11.1.4 |
axsOspfv3AreaAggregatePrefixThe IPv6 Prefix.ro Ipv6AddressPrefix (IPV6-TC) .1.3.6.1.4.1.21839.2.2.1.15.11.1.5 |
axsOspfv3AreaAggregatePrefixLenThe length of the prefix (in bits). A prefix can
not be shorter than 3 bits.ro INTEGER ( 3..128 ) -- UNITS "bits" .1.3.6.1.4.1.21839.2.2.1.15.11.1.6 |
axsOspfv3AreaAggregateStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.15.11.1.7 |
axsOspfv3AreaAggregateEffectPrefixes subsumed by ranges either trigger the
advertisement of the indicated aggregate (ad-
vertiseMatching), or result in the prefix not
being advertised at all outside the area.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.15.11.1.8 |
axsUlr OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.20 |
axsUlrGlobalInfo OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.20.1 |
axsUlrVersionThe version number of flash request packets transmit by the device.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.1.1 |
axsUlrIDIdentifier of device.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.20.1.2 |
axsUlrConfigurationPortCountsThe number of primary port and secondary port in device.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.1.3 |
axsUlrStartupActivePortSelectionThe configuration of startup active port selection.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.1.4 |
axsUlrPortTableA table containing uplink port information. SEQUENCE OF AxsUlrPortEntry .1.3.6.1.4.1.21839.2.2.1.20.2 |
axsUlrPortEntryAn entry containing uplink port. AxsUlrPortEntry .1.3.6.1.4.1.21839.2.2.1.20.2.1 |
axsUlrPortIfIndexIfIndex of the port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.1 |
axsUlrPortTypeType of port.
1) Primary
2) Secondaryro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.2 |
axsUlrPairedPortIfIndexIfIndex of paired port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.3 |
axsUlrPortStatusThe state of port.
1) Forwarding
2) Down
3) Blockingro Enumeration .1.3.6.1.4.1.21839.2.2.1.20.2.1.4 |
axsUlrPairedPortStatusThe state of paired port.
1) Forwarding
2) Down
3) Blockingro Enumeration .1.3.6.1.4.1.21839.2.2.1.20.2.1.5 |
axsUlrAutoChangeToPrimaryThe configuration of preemption.
1) Off
2) Onro Enumeration .1.3.6.1.4.1.21839.2.2.1.20.2.1.6 |
axsUlrAutoChangeToPrimaryDelayThe Delay time of preemption.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.7 |
axsUlrAutoChangeToPrimaryRestThe rest time of preemption.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.8 |
axsUlrStartupActivePortSelectionStatusThe state of startup active port selection.
1) Off
2) Onro Enumeration .1.3.6.1.4.1.21839.2.2.1.20.2.1.9 |
axsUlrFlushTransmitThe configuration of transmit flush-request frame.
1) Off
2) Onro Enumeration .1.3.6.1.4.1.21839.2.2.1.20.2.1.10 |
axsUlrFlushVlanThe transmit VLAN ID in flush-request frame. 0 is not configuration.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.11 |
axsUlrMacAddressUpdateTransmitThe number of transmit MAC Address update frame in one opportunity.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.12 |
axsUlrLastActivePortDecisionTimeLast determinate time of the active port.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.20.2.1.13 |
axsUlrLastFlushTransmitTimeLast transmit time of flush-request frame.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.20.2.1.14 |
axsUlrLastMacUpdateTransmitTimeLast transmit time of MAC Address update frame.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.20.2.1.15 |
axsUlrLastChangeFactorLast determinate factor of the active port.
1) command
2) configure
3) primary down
4) primary up
5) secondary down
6) secondary up
7) preemptionro Enumeration .1.3.6.1.4.1.21839.2.2.1.20.2.1.16 |
axsUlrFlushTransmitTotalPacketsThe total number of transmit flush-request frame in the port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.17 |
axsUlrMacAddressUpdateTransmitTotalPacketsThe total number of transmit MAC Address update frame in the port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.18 |
axsUlrMacAddressUpdateTransmitOverFlowThe over flow number of MAC Address update frame.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.19 |
axsUlrActiveDecisionCountThe determinate number of active port in uplink port.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.20.2.1.20 |
axsBootManagement OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.51 |
axsBootReasonReason of system start.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.51.1 |
axsLogin OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.52 |
axsLoginNameLog in user name. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.52.1 |
axsLoginTimeDate, time and time zone of user log in.
Format : YYYY/MM/DD hh:mm:ss XXXXXX(time zone)
Time zone format :
JST : JST
GMT+09 : GMT + 09 hours
GMT+10 : GMT + 10 hours DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.52.2 |
axsLogoutTimeDate, time and time zone of user log out.
Format : YYYY/MM/DD hh:mm:ss XXXXXX(time zone)
Time zone format :
JST : JST
GMT+09 : GMT + 09 hours
GMT+10 : GMT + 10 hours DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.52.3 |
axsLoginFailureTimeDate, time and time zone of user log in failure.
Format : YYYY/MM/DD hh:mm:ss XXXXXX(time zone)
Time zone format :
JST : JST
GMT+09 : GMT + 09 hours
GMT+10 : GMT + 10 hours DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.52.4 |
axsLoginLocationTerminal information of log in user.
The status will be 'console' or 'aux'.
If other, displays 'TERMINAL(APLLICATION)'.
ex. 'tty/1(telnet)' DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.52.5 |
axsLoginLineConnection information of log in user.
The status will be 'console' or 'aux'.
If other, displays 'IPADDRESS(APLLICATION)'.
ex. '192.168.11.1(telnet)' DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.52.6 |
axsLogoutStatusLog out factor.
error(1) : log out due to none of bellow
success(2) : log out due to command
timeout(3) : log out due to 'auto-logout'
disconnect(4) : log out due to line disconnection
force(5) : log out due to other user's command Enumeration .1.3.6.1.4.1.21839.2.2.1.52.7 |
axslldp OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.100 |
axslldpConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.100.1 |
axslldpMessageTxIntervalLDPDU transmitting intervalro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.1.1 |
axslldpMessageTxHoldMultiplierTime coefficient for contiguity equipment to hold about the LLDP frame which this equipment transmittedro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.1.2 |
axslldpPortConfigTableThe table about LDPDU transmission SEQUENCE OF AxslldpPortConfigEntry .1.3.6.1.4.1.21839.2.2.1.100.1.6 |
axslldpPortConfigEntryThe entry about LDPDU transmission AxslldpPortConfigEntry .1.3.6.1.4.1.21839.2.2.1.100.1.6.1 |
axslldpPortConfigPortNumPort discernment index INTEGER .1.3.6.1.4.1.21839.2.2.1.100.1.6.1.2 |
axslldpPortConfigAdminStatusThe port state of this equipment about transmission and reception of LDPDUro Enumeration .1.3.6.1.4.1.21839.2.2.1.100.1.6.1.3 |
axslldpPortConfigTLVsTxEnableThe TLV state about the port concerned which can be transmittedro Bits .1.3.6.1.4.1.21839.2.2.1.100.1.6.1.4 |
axslldpPortConfigRowStatusThe state of this entryro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.100.1.6.1.5 |
axslldpStats OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.100.2 |
axslldpStatsTableThe table about LLDP statistics information SEQUENCE OF AxslldpStatsEntry .1.3.6.1.4.1.21839.2.2.1.100.2.1 |
axslldpStatsEntryThe Entry about LLDP statistics information AxslldpStatsEntry .1.3.6.1.4.1.21839.2.2.1.100.2.1.1 |
axslldpStatsPortNumPort discernment index INTEGER .1.3.6.1.4.1.21839.2.2.1.100.2.1.1.2 |
axslldpStatsOperStatusThe employment state about the port concernedro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.2.1.1.3 |
axslldpStatsFramesInErrorsThe number of inaccurate LDPDU reception about the port concernedro Counter .1.3.6.1.4.1.21839.2.2.1.100.2.1.1.4 |
axslldpStatsFramesInTotalThe total number of LDPDU reception about the port concernedro Counter .1.3.6.1.4.1.21839.2.2.1.100.2.1.1.5 |
axslldpStatsFramesOutTotalThe total number of LDPDU transmission about the port concernedro Counter .1.3.6.1.4.1.21839.2.2.1.100.2.1.1.6 |
axslldpStatsTLVsInErrorsThe number of inaccurate TLV reception about the port concernedro Counter .1.3.6.1.4.1.21839.2.2.1.100.2.1.1.7 |
axslldpStatsTLVsDiscardedTotalThe total abandonment TLV number about the port concernedro Counter .1.3.6.1.4.1.21839.2.2.1.100.2.1.1.8 |
axslldpLocalSystemData OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.100.3 |
axslldpLocChassisTypeThe chassis type about this equipmentro Enumeration .1.3.6.1.4.1.21839.2.2.1.100.3.1 |
axslldpLocChassisIdThe chassis ID about this equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.3.2 |
axslldpLocSysNameThe chassis ID about this equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.3.3 |
axslldpLocSysDescSystem information about this equipmentro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.100.3.4 |
axslldpLocPortTableThe table about the port of this equipment SEQUENCE OF AxslldpLocPortEntry .1.3.6.1.4.1.21839.2.2.1.100.3.7 |
axslldpLocPortEntryThe entry about the port of this equipment AxslldpLocPortEntry .1.3.6.1.4.1.21839.2.2.1.100.3.7.1 |
axslldpLocPortNumPort discernment index INTEGER .1.3.6.1.4.1.21839.2.2.1.100.3.7.1.1 |
axslldpLocPortTypeThe port type about the port concerned of this equipmentro Enumeration .1.3.6.1.4.1.21839.2.2.1.100.3.7.1.2 |
axslldpLocPortIdThe port ID about the port concerned of this equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.3.7.1.3 |
axslldpLocPortDescPort information about the port concerned of this equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.3.7.1.4 |
axslldpRemoteSystemData OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.100.4 |
axslldpRemTableThe table about contiguity equipment SEQUENCE OF AxslldpRemEntry .1.3.6.1.4.1.21839.2.2.1.100.4.1 |
axslldpRemEntryThe entry about contiguity equipment AxslldpRemEntry .1.3.6.1.4.1.21839.2.2.1.100.4.1.1 |
axslldpRemLocalPortNumThe discernment index of the port of this equipment which received the information about contiguity equipmentro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.2 |
axslldpRemIndexThe index about contiguity equipmentro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.3 |
axslldpRemRemoteChassisTypeThe chassis type about contiguity equipmentro Enumeration .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.4 |
axslldpRemRemoteChassisThe chassis ID about contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.5 |
axslldpRemRemotePortTypeThe port type about the port concerned of contiguity equipmentro Enumeration .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.6 |
axslldpRemRemotePortThe port ID about the port concerned of contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.7 |
axslldpRemPortDescInformation about the port concerned of contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.8 |
axslldpRemSysNameThe system name about contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.9 |
axslldpRemSysDescSystem information about contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.4.1.1.10 |
axslldpRemoteOriginInfoData OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.100.20 |
axslldpRemOriginInfoTableThe table about original with AlaxalA networks TLV of contiguity equipment SEQUENCE OF AxslldpRemOriginInfoEntry .1.3.6.1.4.1.21839.2.2.1.100.20.1 |
axslldpRemOriginInfoEntryThe entry about original with AlaxalA networks TLV of contiguity equipment AxslldpRemOriginInfoEntry .1.3.6.1.4.1.21839.2.2.1.100.20.1.1 |
axslldpRemOriginInfoPortNumThe discernment index of the port of this equipment which received the information about contiguity equipment. INTEGER .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.1 |
axslldpRemOriginInfoIndexThe index about contiguity equipment INTEGER .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.2 |
axslldpRemOriginInfoLowerVlanListWhat expressed effective VLAN ID by the bit map by VLAN 1-2047 in the port concerned of contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.3 |
axslldpRemOriginInfoHigherVlanListWhat expressed effective VLAN ID by the bit map by VLAN 2048-4095 in the port concerned of contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.4 |
axslldpRemOriginInfoIPv4AddressIPv4 address given to the port concerned of contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.5 |
axslldpRemOriginInfoIPv4PortTypePort classification of the port of contiguity equipment concernedro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.6 |
axslldpRemOriginInfoIPv4VlanIdThe smallest thing among VLAN ID to which IPv4 address is givenro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.7 |
axslldpRemOriginInfoIPv6AddressThe IPv6 address given to the port concerned of contiguity equipmentro OCTET STRING .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.8 |
axslldpRemOriginInfoIPv6PortTypePort classification of the port of contiguity equipment concernedro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.9 |
axslldpRemOriginInfoIPv6VlanIdThe smallest thing among VLAN ID to which the IPv6 address is givenro INTEGER .1.3.6.1.4.1.21839.2.2.1.100.20.1.1.10 |
axsAxrp OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.200 |
axsAxrpGroupTableThe table containing AXRP group information. SEQUENCE OF AxsAxrpGroupEntry .1.3.6.1.4.1.21839.2.2.1.200.1 |
axsAxrpGroupEntryThe list of AXRP group information. AxsAxrpGroupEntry .1.3.6.1.4.1.21839.2.2.1.200.1.1 |
axsAxrpGroupRingIdAXRP group ring identifier. INTEGER .1.3.6.1.4.1.21839.2.2.1.200.1.1.1 |
axsAxrpGroupRowStatusValid/Invalid state of this entry. Valid(1) fixedro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.200.1.1.2 |
axsAxrpGroupModeOperation mode of each ring ID.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.3 |
axsAxrpGroupRingAttributeWhen the multi ring is composed, it is an attribute of this device in the common link non-watch ring.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.4 |
axsAxrpGroupMonitoringStateOperation and state of watch of ring.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.5 |
axsAxrpGroupRingport1IfIndex of ring port 1 (port in one where Ifindex is small)ro INTEGER .1.3.6.1.4.1.21839.2.2.1.200.1.1.6 |
axsAxrpGroupRingport1SharedRing port 1 is common port information.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.7 |
axsAxrpGroupRingport2IfIndex of ring port 2 (port in one where Ifindex is large)ro INTEGER .1.3.6.1.4.1.21839.2.2.1.200.1.1.8 |
axsAxrpGroupRingport2SharedRing port 2 is common port information.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.9 |
axsAxrpGroupTransitionToFaultCountsFrequency that shifts from state of trouble watch in state of restoration watch.ro Counter .1.3.6.1.4.1.21839.2.2.1.200.1.1.10 |
axsAxrpGroupTransitionToNormalCountsFrequency that shifts from state of restoration watch in state of trouble watch.ro Counter .1.3.6.1.4.1.21839.2.2.1.200.1.1.11 |
axsAxrpGroupLastTransitionTimeIt is changing the final time to restoration from the trouble or the trouble from restoration.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.200.1.1.12 |
axsAxrpGroupLinkStatusAlertState of each ring ID of link trouble detection.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.13 |
axsAxrpGroupRingport1LinkKeepaliveSendState of transmission of link trouble watch frame of ring port 1.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.14 |
axsAxrpGroupRingport1LinkKeepaliveMonitorState of link trouble watch of ring port 1.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.15 |
axsAxrpGroupRingport1LinkStateState of link of ring port 1.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.16 |
axsAxrpGroupRingport1LinkKeepaliveReceiveCountsNumber of reception frames of link state watch frames of ring port 1.ro Counter .1.3.6.1.4.1.21839.2.2.1.200.1.1.17 |
axsAxrpGroupRingport2LinkKeepaliveSendState of transmission of link trouble watch frame of ring port 2.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.18 |
axsAxrpGroupRingport2LinkKeepaliveMonitorState of link trouble watch of ring port 2.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.19 |
axsAxrpGroupRingport2LinkStateState of link of ring port 2.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.20 |
axsAxrpGroupRingport2LinkKeepaliveReceiveCountsNumber of reception frames of link state watch frames of ring port 2.ro Counter .1.3.6.1.4.1.21839.2.2.1.200.1.1.21 |
axsAxrpGroupMultiFaultDetectionStateOperation and state of multiple fault detection of ring.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.1.1.22 |
axsAxrpVlanGroupTableThe table containing AXRP VLAN group information. SEQUENCE OF AxsAxrpVlanGroupEntry .1.3.6.1.4.1.21839.2.2.1.200.2 |
axsAxrpVlanGroupEntryThe list of AXRP VLAN group information. AxsAxrpVlanGroupEntry .1.3.6.1.4.1.21839.2.2.1.200.2.1 |
axsAxrpVlanGroupRingIdAXRP VLAN ring group number(1~8) INTEGER .1.3.6.1.4.1.21839.2.2.1.200.2.1.1 |
axsAxrpVlanGroupIdAXRP VLAN group number(1~8) INTEGER .1.3.6.1.4.1.21839.2.2.1.200.2.1.2 |
axsAxrpVlanGroupRingport1IfIndex of ring port 1 (port in one where Ifindex is small)ro INTEGER .1.3.6.1.4.1.21839.2.2.1.200.2.1.3 |
axsAxrpVlanGroupRingport1RoleRole of ring port 1ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.2.1.4 |
axsAxrpVlanGroupRingport1OperStatePresent of ring port 1ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.2.1.5 |
axsAxrpVlanGroupRingport2IfIndex of ring port 2 (port in one where Ifindex is small)ro INTEGER .1.3.6.1.4.1.21839.2.2.1.200.2.1.6 |
axsAxrpVlanGroupRingport2RoleRole of ring port 2ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.2.1.7 |
axsAxrpVlanGroupRingport2OperStatePresent of ring port 2ro Enumeration .1.3.6.1.4.1.21839.2.2.1.200.2.1.8 |
axsPconMIB OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.300 |
axsPconObjects OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.300.1 |
axsPconModuleData OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.300.1.1 |
axsPconModuleTableA table containing electric power control information of module. SEQUENCE OF AxsPconModuleEntry .1.3.6.1.4.1.21839.2.2.1.300.1.1.1 |
axsPconModuleEntryAn entry containing electric power control information of module. AxsPconModuleEntry .1.3.6.1.4.1.21839.2.2.1.300.1.1.1.1 |
axsPconModuleIndexA unique value for each module contained by the network device. Integer32 .1.3.6.1.4.1.21839.2.2.1.300.1.1.1.1.1 |
axsPconModuleTypeAn indication of the type of module.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.300.1.1.1.1.2 |
axsPconModuleSlotNoPosition information of the module slots.ro Integer32 .1.3.6.1.4.1.21839.2.2.1.300.1.1.1.1.3 |
axsPconModuleDescrThe textual description of module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.300.1.1.1.1.4 |
axsPconModuleStatusThe module status of this axsPconModuleEntry.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.300.1.1.1.1.5 |
axsPconModuleModeThe module mode of this axsPconModuleEntry.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.300.1.1.1.1.6 |
axsPconPowerCon OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.300.1.2 |
axsPconPowerConTableThe power consumption information table. SEQUENCE OF AxsPconPowerConEntry .1.3.6.1.4.1.21839.2.2.1.300.1.2.1 |
axsPconPowerConEntryThe power consumption information entry. AxsPconPowerConEntry .1.3.6.1.4.1.21839.2.2.1.300.1.2.1.1 |
axsPconPowerConMaxPowerThe maximum electric power of module.ro Gauge .1.3.6.1.4.1.21839.2.2.1.300.1.2.1.1.1 |
axsPconPowerConPowerConsumptionThe power consumption of module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.300.1.2.1.1.2 |
axsPconPowerConPowerMeterThe power meter of module.ro Gauge .1.3.6.1.4.1.21839.2.2.1.300.1.2.1.1.3 |
axsPconTraffic OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.300.1.3 |
axsPconTrafficTableThe Traffic information table. SEQUENCE OF AxsPconTrafficEntry .1.3.6.1.4.1.21839.2.2.1.300.1.3.1 |
axsPconTrafficEntryThe Traffic information entry. AxsPconTrafficEntry .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1 |
axsPconTrafficMaxTransferCapacityThe maximum transfer capacity.ro Gauge .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.1 |
axsPconTrafficTotalTransferCapacityThe total transfer capacity.ro Gauge .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.2 |
axsPconTrafficInOctetsThe total number of octets that received on this module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.3 |
axsPconTrafficOutOctetsThe total number of octets transmitted out from this module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.4 |
axsPconTrafficInPktsThe total number of packets that received on this module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.5 |
axsPconTrafficOutPktsThe total number of packets transmitted out from this module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.6 |
axsPconTrafficCapacityOctetsThe accumulation octets capacity that can be received on this module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.7 |
axsPconTrafficInPeakOctetsRateThe peak rate of octets that received on this module.ro Gauge .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.8 |
axsPconTrafficPeakTransferCapacityThe rate of margin when incoming traffic is peak.ro Gauge .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.9 |
axsPconTrafficInDiscPktsThe total number of discarded packets on this module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.300.1.3.1.1.10 |
axsStack OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.400 |
axsStackGlobalInfo OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.400.1 |
axsStackMasterSwitchMaster switch number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.400.1.1 |
axsStackMember OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.400.2 |
axsStackMemberTableTable of the stack member information. SEQUENCE OF AxsStackMemberEntry .1.3.6.1.4.1.21839.2.2.1.400.2.1 |
axsStackMemberEntryEntry of the stack member information. AxsStackMemberEntry .1.3.6.1.4.1.21839.2.2.1.400.2.1.1 |
axsStackMemberIndexA number to specify axsStackMemberEntry. INTEGER .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.1 |
axsStackModelTypeModel type of this system.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.2 |
axsStackSoftwareNameSoftware name of this system.ro DisplayString .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.3 |
axsStackSoftwareAbbreviationSystem software abbreviation.ro DisplayString .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.4 |
axsStackSoftwareVersionSystem software version.ro DisplayString .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.5 |
axsStackBootReasonReason of system start.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.6 |
axsStackPconModuleModePower mode of operation of the entire device.ro Enumeration .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.7 |
axsStackPconPowerConMaxPowerThe maximum electric power of module.ro Gauge .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.8 |
axsStackPconPowerConPowerConsumptionThe power consumption of module.ro Counter64 .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.9 |
axsStackPconPowerConPowerMeterThe power meter of module.ro Gauge .1.3.6.1.4.1.21839.2.2.1.400.2.1.1.10 |
axsStackMemberLicense OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.1.400.3 |
axsStackMemberLicenseTableThe table containing the license information. SEQUENCE OF AxsStackMemberLicenseEntry .1.3.6.1.4.1.21839.2.2.1.400.3.1 |
axsStackMemberLicenseEntryThe entry of license information. AxsStackMemberLicenseEntry .1.3.6.1.4.1.21839.2.2.1.400.3.1.1 |
axsStackMemberLicenseIndexThe unique index number given for each serial number. The number is from 1 to ax1230sLicenseNumber. INTEGER .1.3.6.1.4.1.21839.2.2.1.400.3.1.1.1 |
axsStackMemberLicenseSerialNumberThe serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.400.3.1.1.2 |
axsStackMemberLicenseOptionNumberThe number of option licenses associated with the serial number.ro INTEGER .1.3.6.1.4.1.21839.2.2.1.400.3.1.1.3 |
axsStackMemberLicenseOptionTableThe table containing option licenses information associated with the serial number. SEQUENCE OF AxsStackMemberLicenseOptionEntry .1.3.6.1.4.1.21839.2.2.1.400.3.2 |
axsStackMemberLicenseOptionEntryThe entry of the option license information associated with the serial number. AxsStackMemberLicenseOptionEntry .1.3.6.1.4.1.21839.2.2.1.400.3.2.1 |
axsStackMemberLicenseOptionIndexThe unique index number given for each serial number. The same number as ax1230sLicenseIndex. INTEGER .1.3.6.1.4.1.21839.2.2.1.400.3.2.1.1 |
axsStackMemberLicenseOptionNumberIndexThe unique index number of option licenses information which is given for each serial number. The number is from 1 to ax1230sLicenseNumber. INTEGER .1.3.6.1.4.1.21839.2.2.1.400.3.2.1.2 |
axsStackMemberLicenseOptionSoftwareNameThe software model name of the option license information associated with the serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.400.3.2.1.3 |
axsStackMemberLicenseOptionSoftwareAbbreviationThe software abbreviated name of the option license information associated with the serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.1.400.3.2.1.4 |
ax260aMib OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23 |
ax260aSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.1 |
ax260aModelTypeModel type of this system.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.1.1 |
ax260aSoftware OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.1.2 |
ax260aSoftwareNameSoftware name of this system.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.1.2.1 |
ax260aSoftwareAbbreviationSystem software abbreviation.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.1.2.2 |
ax260aSoftwareVersionSystem software version.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.1.2.3 |
ax260aSystemMsg OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.1.3 |
ax260aSystemMsgTextThe text of the system log message.For information about this code,
see: Operator's Manual.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.1.3.1 |
ax260aSystemMsgTypeThe event type. For information about this code, see: Operator's Manual.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.23.1.3.2 |
ax260aSystemMsgTimeStampThe time that event occured. And that is expressed as type of
MM/DD hh:mm:ss
MM:month(01-12)
DD:day(01-31)
hh:hour(00-23)
mm:minute(00-59)
ss:second(00-59)
Insert space between DD and hh.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.1.3.3 |
ax260aSystemMsgLevelThe newest system message log level.For information about this code,
see: Operator's Manual.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.23.1.3.4 |
ax260aSystemMsgEventPointThe code of part that system message error occured. For information
about this code,see: Operator's Manual.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.1.3.5 |
ax260aSystemMsgEventInterfaceIDInterface identification of system messages. For information
about this code,see: Operator's Manual.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.1.3.6 |
ax260aSystemMsgEventCodeEvent kind code of system messages. For information about this code,
see: Operator's Manual.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.23.1.3.7 |
ax260aSystemMsgAdditionalCodeAdditional code of system messages. For information about this code,
see: Operator's Manual.ro OCTET STRING .1.3.6.1.4.1.21839.2.2.23.1.3.8 |
ax260aSnmpAgent OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.1.4 |
ax260aSnmpSendReceiveSizeSNMP packet data size in Manager-to-Agent communication. The value is
displayed in bytes.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.1.4.1 |
ax260aSnmpReceiveDelayA recommendable interval to receive packets from Manager.The value is
displayed in milliseconds.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.1.4.2 |
ax260aSnmpContinuousSendNumber of times that is recommendable continuous transmission
packets.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.1.4.3 |
ax260aSnmpObjectMaxNumberMax number of objects that contain SNMP packet.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.1.4.4 |
ax260aLicense OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.1.6 |
ax260aLicenseNumberThe number of the configured license serial numbers.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.1.6.1 |
ax260aLicenseTableThe table containing the license information. SEQUENCE OF Ax260aLicenseTableEntry .1.3.6.1.4.1.21839.2.2.23.1.6.2 |
ax260aLicenseEntryThe entry of license information. Ax260aLicenseTableEntry .1.3.6.1.4.1.21839.2.2.23.1.6.2.1 |
ax260aLicenseIndexThe unique index number given for each serial number. The number is from 1 to ax260aLicenseNumber. INTEGER .1.3.6.1.4.1.21839.2.2.23.1.6.2.1.1 |
ax260aLicenseSerialNumberThe serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.23.1.6.2.1.2 |
ax260aLicenseOptionNumberThe number of option licenses associated with the serial number.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.1.6.2.1.3 |
ax260aLicenseOptionTableThe table containing option licenses information associated with the serial number. SEQUENCE OF Ax260aLicenseOptionTableEntry .1.3.6.1.4.1.21839.2.2.23.1.6.3 |
ax260aLicenseOptionEntryThe entry of the option license information associated with the serial number. Ax260aLicenseOptionTableEntry .1.3.6.1.4.1.21839.2.2.23.1.6.3.1 |
ax260aLicenseOptionIndexThe unique index number given for each serial number. The same number as ax260aLicenseIndex. INTEGER .1.3.6.1.4.1.21839.2.2.23.1.6.3.1.1 |
ax260aLicenseOptionNumberIndexThe unique index number of option licenses information which is given for each serial number. The number is from 1 to ax260aLicenseNumber. INTEGER .1.3.6.1.4.1.21839.2.2.23.1.6.3.1.2 |
ax260aLicenseOptionSoftwareNameThe software model name of the option license information associated with the serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.23.1.6.3.1.3 |
ax260aLicenseOptionSoftwareAbbreviationThe software abbreviated name of the option license information associated with the serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.23.1.6.3.1.4 |
ax260aDevice OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.2 |
ax260aChassis OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.2.1 |
ax260aChassisMaxNumberMax number of cluster chassis that can connect to this router.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.1 |
ax260aChassisTableA table containing chassis information. SEQUENCE OF Ax260aChassisTableEntry .1.3.6.1.4.1.21839.2.2.23.2.1.2 |
ax260aChassisEntryAn entry containing specific chassis. Ax260aChassisTableEntry .1.3.6.1.4.1.21839.2.2.23.2.1.2.1 |
ax260aChassisIndexA number to specify ax260aChassisEntry. INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.1 |
ax260aChassisTypeChassis type of this system.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.2 |
ax260aChassisStatusCurrent status of this chassis.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.3 |
ax260aStsLedStatusThe state of STS LED of the device is shown.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.4 |
ax260aCpuNameCPU name is shown by the character string of 16 characters or less.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.5 |
ax260aCpuClockCPU clock is shown by the numerical value.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.6 |
ax260aMemoryTotalSizeThe installing memory size is shown by the numerical value.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.7 |
ax260aMemoryUsedSizeThe use memory size is shown by the numerical value.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.8 |
ax260aMemoryFreeSizeThe unused memory size is shown by the numerical value.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.9 |
ax260aRomVersionThe version of ROM equipped with BCU is shown by the character string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.10 |
ax260aCpuLoad1mCPU utilization of one minute is shown by the numerical value.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.11 |
ax260aFlashTotalSizeThe total of filesystem use capacity and unused capacity in a built-in memory
is shown.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.12 |
ax260aFlashUsedSizeThe use capacity of the filesystem in a built-in memory is shown.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.13 |
ax260aFlashFreeSizeThe unused capacity of the filesystem in a built-in memory is shown.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.14 |
ax260aSdCardStatusThe SD card connection is shown.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.15 |
ax260aSdCardTotalSizeTotal capacity of the SD card is shown by the numerical value. It responds by -1
at the MC card unconnection.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.16 |
ax260aSdCardUsedSizeThe use capacity of the SD card is shown by the numerical value. It responds by -1
at the SD card unconnection.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.17 |
ax260aSdCardFreeSizeThe remainder capacity of the SD card is shown by the numerical value. It
responds by -1 at the SD card unconnection.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.18 |
ax260aPhysLineNumberNumber of physical lines.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.19 |
ax260aTemperatureStatusNumberThe maximum number of ax260aTemperatureStatus in this chassis.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.20 |
ax260aPowerUnitNumberNumber of maximum power switches that this router can connect its.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.21 |
ax260aRedundantPsNumberNumber of external power switches that this router can connect its.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.22 |
ax260aFanNumberThe maximum number of fans that can connect to this chassis.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.23 |
ax260aTotalAccumRunTimeTotal operation time after operation of device begins.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.24 |
ax260aCriticalAccumRunTimeOperating time in critical environmental temperature.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.25 |
ax260aSts2LedStatusThe state of STS2 LED of the device is shown.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.2.1.26 |
ax260aTemperatureStatusTableThe table of ambient temperature status maintained by the
environmental monitor. SEQUENCE OF Ax260aTemperatureStatusEntry .1.3.6.1.4.1.21839.2.2.23.2.1.3 |
ax260aTemperatureStatusEntryAn entry in the ambient temperature status table, representing
the status of the associated testpoint maintained by the
environmental monitor. Ax260aTemperatureStatusEntry .1.3.6.1.4.1.21839.2.2.23.2.1.3.1 |
ax260aTemperatureStatusIndexUnique index for the testpoint being instrumented.
This index is for SNMP purposes only, and has no
intrinsic meaning. INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.3.1.1 |
ax260aTemperatureStatusDescrTextual description of the testpoint being instrumented.
This description is a short textual label, suitable as a
human-sensible identification for the rest of the
information in the entry.ro DisplayString .1.3.6.1.4.1.21839.2.2.23.2.1.3.1.2 |
ax260aTemperatureStatusValueThe current measurement of the testpoint being instrumented.ro Integer32 .1.3.6.1.4.1.21839.2.2.23.2.1.3.1.3 |
ax260aTemperatureThresholdThe highest value that the associated instance of the
object ax260aTemperatureStatusValue may obtain
before an emergency shutdown of the managed device is
initiated.ro Integer32 .1.3.6.1.4.1.21839.2.2.23.2.1.3.1.4 |
ax260aTemperatureStateThe current state of the testpoint being instrumented.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.3.1.5 |
ax260aPowerUnitTableA table containing power unit information. SEQUENCE OF Ax260aPowerUnitTableEntry .1.3.6.1.4.1.21839.2.2.23.2.1.4 |
ax260aPowerUnitEntryAn entry containing power unit information. Ax260aPowerUnitTableEntry .1.3.6.1.4.1.21839.2.2.23.2.1.4.1 |
ax260aPowerUnitIndexA number to position of the power units.The value from 1
to ax260aPowerUnitNumber. INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.4.1.1 |
ax260aPowerConnectStatusThe current connection status of the power unit.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.4.1.2 |
ax260aPowerSupplyStatusStatus of power supply.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.4.1.3 |
ax260aFanTableA table containing fan information. SEQUENCE OF Ax260aFanTableEntry .1.3.6.1.4.1.21839.2.2.23.2.1.5 |
ax260aFanEntryThis entry containing information for a fan. Ax260aFanTableEntry .1.3.6.1.4.1.21839.2.2.23.2.1.5.1 |
ax260aFanIndexIndex to indicate position of fans. INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.5.1.1 |
ax260aFanStatusStatus of fans.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.5.1.2 |
ax260aRedundantPsTableA table containing external power supply information. SEQUENCE OF Ax260aRedundantPsEntry .1.3.6.1.4.1.21839.2.2.23.2.1.6 |
ax260aRedundantPsEntryAn entry containing external power supply information. Ax260aRedundantPsEntry .1.3.6.1.4.1.21839.2.2.23.2.1.6.1 |
ax260aRedundantPsIndexAn index that shows the external power supply position. INTEGER .1.3.6.1.4.1.21839.2.2.23.2.1.6.1.1 |
ax260aRedundantPsConnectStatusMounting an external power supply is shown.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.6.1.2 |
ax260aRedundantPsStatusThe operation of an external power supply is shown.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.1.6.1.3 |
ax260aPhysLine OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.2.2 |
ax260aPhysLineTableA table containing physical port information. SEQUENCE OF Ax260aPhysLineTableEntry .1.3.6.1.4.1.21839.2.2.23.2.2.1 |
ax260aPhysLineEntryAn entry containing physical port. Ax260aPhysLineTableEntry .1.3.6.1.4.1.21839.2.2.23.2.2.1.1 |
ax260aPhysLineIndexPhysical port number. The value is from 1 to ax260aNifLineNumber. INTEGER .1.3.6.1.4.1.21839.2.2.23.2.2.1.1.1 |
ax260aPhysLineConnectorTypeConnector type is connected physical port. The value is 1(other)
when connector is disconnected or connector type is unknown.When
displaying in pannel, requests board name of NIF,then will display it.
The value is -1 when PSU or NIF board is disconnected.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.2.1.1.2 |
ax260aPhysLineOperStatusStatus of physical port. The value is -1 when PSU or NIF board is
disconnected.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.2.1.1.3 |
ax260aPhysLineIfIndexNumberNumber of ifIndex which is included in physical port.The value is -1
when PSU board or NIF board is disconnected.ro INTEGER .1.3.6.1.4.1.21839.2.2.23.2.2.1.1.4 |
ax260aPhysLineTransceiverStatusType and status of replaceable transceiver.ro Enumeration .1.3.6.1.4.1.21839.2.2.23.2.2.1.1.5 |
ax260aDeviceError OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.2.3 |
ax260aMemoryErrorInformation about device error. Enumeration .1.3.6.1.4.1.21839.2.2.23.2.3.1 |
ax260aManagementMIB OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.3 |
ax260aOperationCommand OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.3.1 |
ax260aFdbClearMIB OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.3.1.1 |
ax260aFdbClearSetFdb clear information. When want to clear fdb,
then set value of this MIB as 1.rw Enumeration .1.3.6.1.4.1.21839.2.2.23.3.1.1.1 |
ax260aFdbClearReqTimeThis object indicates the most recent time that
received the demand to clear Fdb information.(sysUpTime)ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.23.3.1.1.2 |
ax260aFdbClearSuccessTimeThis object indicates the time of the most recent
Fdb clearing success.(sysUpTime)ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.21839.2.2.23.3.1.1.3 |
ax260aAuth OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.10 |
ax260aAuthInfo OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.10.1 |
ax260aAuthSysNameSystem name of authentication. DisplayString .1.3.6.1.4.1.21839.2.2.23.10.1.1 |
ax260aAuthIfIndexifIndex of authentication. INTEGER .1.3.6.1.4.1.21839.2.2.23.10.1.2 |
ax260aAuthSupplicantMacMac address of authentication. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.21839.2.2.23.10.1.3 |
ax260aAuthMessageMessage of authentication. DisplayString .1.3.6.1.4.1.21839.2.2.23.10.1.4 |
ax260aDot1x OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.10.2 |
ax260aWauth OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.10.3 |
ax260aMauth OBJECT IDENTIFIER .1.3.6.1.4.1.21839.2.2.23.10.4 |