APPIAN-PPORT-SERIAL-MIB
AI MIB Summary
The APPIAN-PPORT-SERIAL-MIB enables monitoring and management of Appian serial interface hardware, specifically RS232-like ports, by exposing operational status, error counters, and link state metrics for serial communication sessions.
Appian Serial Interface MIB for RS232 like interfaces.
Main OID:
acSerial.1.3.6.1.4.1.2785.2.3.2
23
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
23 total| Object Name |
|---|
acSerialAppian Serial Interface MIB for RS232 like interfaces. MODULE-IDENTITY .1.3.6.1.4.1.2785.2.3.2 |
acSerialTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2785.2.3.2.0 |
acSerialLinkDownTrapThe Serial Port driver for this interface has detected the port to be in the down state. NOTIFICATION-TYPE .1.3.6.1.4.1.2785.2.3.2.0.1 |
acSerialLinkUpTrapThe Serial Port driver for this interface has detected the port to be in the down state. NOTIFICATION-TYPE .1.3.6.1.4.1.2785.2.3.2.0.2 |
acSerialStatsResetTrapThe statistics for this serial port have been reset to zero(0) and may cause problems for long term trending functions. NOTIFICATION-TYPE .1.3.6.1.4.1.2785.2.3.2.0.3 |
acSerialCfgErrorTrapA configuration request for this serial interface has been detected as incorrect or corrupted. NOTIFICATION-TYPE .1.3.6.1.4.1.2785.2.3.2.0.4 |
acSerialTableEach Switch Control Processor supports a debug port as well as a management access or craft CLI port. The system will initialize the acSerialTable when the system boots or an SCP has been reset. SEQUENCE OF AcSerialEntry .1.3.6.1.4.1.2785.2.3.2.1 |
acSerialEntryA row in the serial table contains configurable parameters and statistics for each serial interface on this platform. AcSerialEntry .1.3.6.1.4.1.2785.2.3.2.1.1 |
acSerialNodeIdThe node id is the id for this specific node in the OSAP ring.ro AcNodeId (APPIAN-SMI-MIB) .1.3.6.1.4.1.2785.2.3.2.1.1.1 |
acSerialSlotThe control processor slot upon which the serial port is located.ro INTEGER .1.3.6.1.4.1.2785.2.3.2.1.1.2 |
acSerialPortThe physical port number on acSerialEntrySlot where this connector is located.ro INTEGER .1.3.6.1.4.1.2785.2.3.2.1.1.3 |
acSerialAdminStatusAppian Administrative Status attribute used to set the provisioning state as either activate(1), inactivate(2) or delete(3). Refer to the Appian-SMI.mib file for additional information.rw AcAdminStatus (APPIAN-SMI-MIB) .1.3.6.1.4.1.2785.2.3.2.1.1.4 |
acSerialOpStatusThe current operational status of the serial port driver and services supporting this interface.ro AcOpStatus (APPIAN-SMI-MIB) .1.3.6.1.4.1.2785.2.3.2.1.1.5 |
acSerialOpCodeProvides a detailed status code which can be used to isolate a problem or state condition reported in acSerialEntryOpStatus.ro INTEGER .1.3.6.1.4.1.2785.2.3.2.1.1.6 |
acSerialOpModeDetermines the mode of operation for the serial port. If the serial port is using a raw terminal(1) or if we are to run PPP over this port as an alternative EMS access mechanism.rw Enumeration .1.3.6.1.4.1.2785.2.3.2.1.1.7 |
acSerialBaudRateUser configured baud rate for use on the serial port. When set to Auto(1), the driver will negotiate baud rate.rw Enumeration .1.3.6.1.4.1.2785.2.3.2.1.1.8 |
acSerialParityUser configurable partity which is used on the serial port.rw Enumeration .1.3.6.1.4.1.2785.2.3.2.1.1.9 |
acSerialNumberBitsNumber of bits-per-byte used over the serial port.rw Enumeration .1.3.6.1.4.1.2785.2.3.2.1.1.10 |
acSerialIpAddressThe IP Addressed used on the serial port during PPP sessions. If chSerialMode is equal to PPP-DHCP, this field is not needed otherwise a static IP Address is required in this field.rw IpAddress .1.3.6.1.4.1.2785.2.3.2.1.1.11 |
acSerialIpSubnetThe IP Subnet Mask in dotted notation for use on the serial port during PPP sessions.rw IpAddress .1.3.6.1.4.1.2785.2.3.2.1.1.12 |
acSerialRxOctetsThe number of bytes read by the serial port driver.ro INTEGER .1.3.6.1.4.1.2785.2.3.2.1.1.13 |
acSerialTxOctetsThe number of bytes transmitted by the serial port driver.ro INTEGER .1.3.6.1.4.1.2785.2.3.2.1.1.14 |
acSerialInterfaceNameA user configurable ASCII name of up to 64 bytes in length, which is assigned for this interface.rw DisplayString .1.3.6.1.4.1.2785.2.3.2.1.1.15 |