AGENT-GENERAL-MIB
AI MIB Summary
The AGENT-GENERAL-MIB defines the foundational structure for enterprise-specific management information, providing the standard framework for generic system metrics such as system uptime, contact details, location, and object identifiers (OIDs) across SNMP-capable network devices. It serves as the mandatory base module for all enterprise MIBs, enabling the retrieval of core device status and configuration parameters required for basic network monitoring and inventory management.
The structure of general management information for enterprise.
Main OID:
agentGeneralMgmt.1
287
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
287 total| Object Name |
|---|
agentGeneralMgmtThe structure of general management information for enterprise. MODULE-IDENTITY .1 |
agentBasicInfo OBJECT IDENTIFIER .1.1 |
agentMgmtProtocolCapabilityThe network management protocol(s) supported by this agent.ro Enumeration .1.1.1 |
agentMibCapabilityTableA list of MIB capability entries supported by this agent. SEQUENCE OF AgentMibCapabilityEntry .1.1.2 |
agentMibCapabilityEntryA MIB capability entry containing objects that describe a particular MIB
supported by this agent. AgentMibCapabilityEntry .1.1.2.1 |
agentMibCapabilityIndexA list of Agent MIB Capability Description entries.ro Integer32 .1.1.2.1.1 |
agentMibCapabilityDescrThe name of the MIB supported by the agent.ro DisplayString .1.1.2.1.2 |
agentMibCapabilityVersionThe version of the MIB specified in this entry.ro Integer32 .1.1.2.1.3 |
agentMibCapabilityTypeThe type of MIB specified in this entry.ro Enumeration .1.1.2.1.4 |
agentStatusConsoleInUseThis indicates whether the console is currently in use.ro Enumeration .1.1.3 |
agentStatusSaveCfgThis indicates the status of the device configuration.
other (1) - This entry is currently in use but the conditions under
which it will remain so are determined by each of the following values.
proceeding (2) - The device configuration is currently being saved into NV-RAM.
completed (3) - All of the device configuration parameters have been
saved into NV-RAM.
failed (4) - The process to save the device configuration has failed.ro Enumeration .1.1.4 |
agentStatusFileTransferThe status of the firmware download control. If the value is stated as 'other',
the firmware has not been updated since the device was started.ro Enumeration .1.1.5 |
agentCPUutilization OBJECT IDENTIFIER .1.1.6 |
agentCPUutilizationIn5secThe time scale is set at 5 second intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.1.6.1 |
agentCPUutilizationIn1minThe time scale is set at 1 minute intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.1.6.2 |
agentCPUutilizationIn5minThe time scale is set at 5 minute intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.1.6.3 |
agentDualImageStatusThe dual image status.ro Enumeration .1.1.7 |
agentPORTutilizationTableThis table specifies the current utilization of a specified port. SEQUENCE OF AgentPORTutilizationEntry .1.1.8 |
agentPORTutilizationEntryA list of information regarding the port utilization function. AgentPORTutilizationEntry .1.1.8.1 |
agentPORTutilizationProtIndexThis object indicates the module's port number.ro INTEGER .1.1.8.1.1 |
agentPORTutilizationTXThe current rate of transmitted frames on the specified port.ro INTEGER .1.1.8.1.2 |
agentPORTutilizationRXThe current rate of received frames on the specified port.ro INTEGER .1.1.8.1.3 |
agentPORTutilizationUtilThe current percentages regarding port statistics.ro INTEGER .1.1.8.1.4 |
agentDRAMutilizationTableInformation about DRAM memory. SEQUENCE OF AgentDRAMutilizationEntry .1.1.9 |
agentDRAMutilizationEntryA list of information about DRAM memory. AgentDRAMutilizationEntry .1.1.9.1 |
agentDRAMutilizationUnitIDSpecifies the unit ID.
If the ID equals zero, it means the current device.ro INTEGER .1.1.9.1.1 |
agentDRAMutilizationTotalDRAMThe size of total DRAM memory.ro INTEGER UNITS "KB" .1.1.9.1.2 |
agentDRAMutilizationUsedDRAMThe size of used DRAM memory.ro INTEGER UNITS "KB" .1.1.9.1.3 |
agentDRAMutilizationThe percentage of used DRAM memory of the total DRAM memory available.
The value will be between 0% (idle) and 100% (very busy).ro INTEGER .1.1.9.1.4 |
agentFLASHutilizationTableInformation about the flash memory. SEQUENCE OF AgentFLASHutilizationEntry .1.1.10 |
agentFLASHutilizationEntryInformation about the flash memory. AgentFLASHutilizationEntry .1.1.10.1 |
agentFLASHutilizationUnitIDSpecifies the unit ID.
If the ID equals zero, it means the current device.ro INTEGER .1.1.10.1.1 |
agentFLASHutilizationTotalFLASHThe total size of flash memory.ro INTEGER UNITS "KB" .1.1.10.1.2 |
agentFLASHutilizationUsedFLASHThe size of the used flash memory.ro INTEGER UNITS "KB" .1.1.10.1.3 |
agentFLASHutilizationThe percentage of used flash memory in total flash memory.
The value will be between 0% (idle) and 100% (very busy).ro INTEGER .1.1.10.1.4 |
agentStatusResetThis indicates the status of 'agentReset'.ro Enumeration .1.1.11 |
agentSerialNumberA text string containing the serial number of this device.ro DisplayString (SNMPv2-TC) .1.1.12 |
agentFirmwareTypeA text string containing the firmware type.ro DisplayString (SNMPv2-TC) .1.1.13 |
agentBasicConfig OBJECT IDENTIFIER .1.2 |
agentBscSwFileTableA list of MIB Basic Config entry support files updated by this agent. SEQUENCE OF AgentBscSwFileEntry .1.2.1 |
agentBscSwFileEntryA basic configuration entry containing the objects that describe a particular MIB
supported by this agent. AgentBscSwFileEntry .1.2.1.1 |
agentBscSwFileIndexThe table index for the file entryro Integer32 .1.2.1.1.1 |
agentBscSwFileDscrThe description of the software file purpose in this entry.
Note: For systems that do not support a change to this object, setting a value for
this object will cause the system to return bad-value error messages.rw DisplayString .1.2.1.1.2 |
agentBscSwFileAddrThe IP address where the file that needs to be downloaded is located, or the IP address
where the file will be uploaded to.rw IpAddress .1.2.1.1.3 |
agentBscSwFileTransferTypeThe channel through which the file will be downloaded or uploaded.
Note: For systems that do not support all channels, setting a value to the unsupported
channel will cause the system to return bad-value error messages.rw Enumeration .1.2.1.1.4 |
agentBscSwFileThe name of the file to be downloaded from, or uploaded to, the TFTP server.rw DisplayString .1.2.1.1.5 |
agentBscSwFileLocateIdThis object describes the type of file.
runtime-code (1),
log-file (2),
cfg-file (3)
Note: For systems that do not support changes to this object, setting a value for
this object will cause the system to return bad-value error messages.rw INTEGER .1.2.1.1.6 |
agentBscSwFileLoadTypeThis object provides the user with a choice of uploading or downloading the selected file.
Note: For systems that do not support a change to this object, setting a value for this object
will cause the system to return bad-value error messages.rw Enumeration .1.2.1.1.7 |
agentBscSwFileCtrlThis object gives the user the option of downloading runtime software. This setting will take effect
when the system restarts. See Note (1) below
Note:
For systems that do not support changes to this object, setting a value to this object
will cause the system to return bad-value error messages.
start - Activate firmware.
delete (4) - Delete the firmware by indicated firmware ID.
config-as-bootup (5) - Configured as bootup firmware by the indicated
firmware(ID).
apply (6) - Apply the configuration to be the active configuration by the indicated config ID.rw Enumeration .1.2.1.1.8 |
agentBscSwFileBIncrementThis object indicates whether the previous configuration will remain
valid or not after downloading the configuration file.
True: Keep valid
False: Erase.rw TruthValue (SNMPv2-TC) .1.2.1.1.9 |
agentBscSwFileCtrlIDThe section ID of the firmware image or configuration file.
A value of 0 indicates the boot-up firmware image or configuration file.rw INTEGER .1.2.1.1.10 |
agentBscSwFileCtrlUnitIDSpecifies which unit of the switch stack the firmware image will be downloaded from.
One or more units can be set in this list. Each bit from the left to the right represents the
switch from unit ID 1 to unit ID 12.
A null entry in this field denotes all switches in the switch stack.rw UnitList .1.2.1.1.11 |
agentBscSwFileIPv6AddrThe IPv6 address where the file will be downloaded from or uploaded to.rw Ipv6Address .1.2.1.1.12 |
agentBscSwFileBootUpImageThe result of the download will depend on whether the boot_up option is specified.
Case 1: In the case where the master unit provides the file system and the slave unit does
not provide the file system, when boot_up is specified, the file will be downloaded
to the boot_up image on the slave. If boot_up is not specified, then the file will
not be downloaded to this slave unit.
Case 2: In the case where the master unit does not provide the file system and the slave unit
provides the file system, when boot_up is specified, the file will be downloaded to
the boot_up image on the slave unit. If boot_up is not specified, the file will
not be downloaded to this slave unit.
Case 3: In the case where the master unit and the slave unit both support or do not support
the file system, the file will be downloaded to the specified file on the slave unit.
If boot_up is specified, the downloaded file will be assigned as the boot_up image.
True: boot_up option is specified.
False: boot_up option is not specified.rw TruthValue (SNMPv2-TC) .1.2.1.1.13 |
agentBscSwFileForceAgreeWhen the force_agree option is specified, the reboot command will be executed
immediately, without any further confirmation from the user.
True: force_agree option is specified.
False: force_agree option is not specified.rw TruthValue (SNMPv2-TC) .1.2.1.1.14 |
agentBscSwFileInterfaceNameThis node is used to specify the interface name when the agentBscSwFileIPv6Addr
is the link local address.rw DisplayString .1.2.1.1.15 |
agentBscSwFileServerDomainNameThis object indicates the domain name of the TFTP server.rw DisplayString .1.2.1.1.16 |
agentFileTransferThis object will execute the download or upload action. If start (2) is chosen, it will
begin to download/upload and no reset will follow. If start-and-reset (3) is chosen,
then the reset will be activated after completing the download or upload.
No action if noaction (4) is chosen.
Note:
Because these functions will be limited by the support for the system in question,
some of the selected items will be invalid. When the user selects an invalid entry,
the system will respond with a bad-value status.rwobsolete Enumeration .1.2.2 |
agentSystemResetThis object indicates the agent system reset state. Setting this
object to no-reset (4) has no effect. Setting this object to
cold-start (2) or warm-start (3) will reset the agent. The agent
always returns to no-reset (4) when this object is read.
This object is replaced by 'agentReset'.rwdeprecated Enumeration .1.2.3 |
agentRs232PortConfigThis object indicates the RS-232C mode once the device has restarted.rw Enumeration .1.2.4 |
agentOutOfBandBaudRateConfigThis object allows the user to specify an out-of-band baud rate, which
will take effect upon system restart.
Note:
Because these functions will be limited by the support for the system
in question, some of the selected items will be invalid. When the user
selects an invalid entry, the system will respond with a bad-value error message.rwobsolete Enumeration .1.2.5 |
agentSaveCfgThis object indicates the type of save command to be executed, when saving to NV-RAM.
other (1) - None of the following.
cfg-id1 (2) - Save configuration ID1.
cfg-id2 (3)- Save configuration ID2.
log (4) - Save log.
all (5) - Save both (active configuration and log).rw Enumeration .1.2.6 |
swMultiImageInfoTable SEQUENCE OF SwMultiImageInfoEntry .1.2.7 |
swMultiImageInfoEntryA list of information about multiple image management. SwMultiImageInfoEntry .1.2.7.1 |
swMultiImageInfoIDThe stacking section ID of the firmware image.
The stacking section ID = 256 * Unit ID + Image File ID.ro INTEGER .1.2.7.1.1 |
swMultiImageVersionThe recorded downloaded firmware version.ro DisplayString .1.2.7.1.2 |
swMultiImageSizeThe recorded downloaded firmware size.ro Integer32 .1.2.7.1.3 |
swMultiImageUpdateTimeThe recorded firmware update time.ro DisplayString .1.2.7.1.4 |
swMultiImageFromThe recorded IP address of the TFTP serverro DisplayString .1.2.7.1.5 |
swMultiImageSendUserThe record of the user who downloaded the firmware.ro DisplayString .1.2.7.1.6 |
swMultiImageFileNameWhen the system is set to boot from SD card, this object will display the recorded path name of the boot firmware file.ro DisplayString .1.2.7.1.7 |
agentMultiCfgMgmt OBJECT IDENTIFIER .1.2.8 |
swMultiCfgInfoTable SEQUENCE OF SwMultiCfgInfoEntry .1.2.8.1 |
swMultiCfgInfoEntryA list of information about multiple configuration files. SwMultiCfgInfoEntry .1.2.8.1.1 |
swMultiCfgInfoIDThe section ID of the configuration files.ro INTEGER .1.2.8.1.1.1 |
swMultiCfgVersionThe recorded downloaded configuration version.ro DisplayString .1.2.8.1.1.2 |
swMultiCfgSizeThe recorded downloaded configuration size (in bytes).ro Integer32 .1.2.8.1.1.3 |
swMultiCFgUpdateTimeThe recorded configuration update time
displayed in string format, i.e. yyyy/mon/dd hh:mm:ss.ro DisplayString .1.2.8.1.1.4 |
swMultiCfgFromThe recorded IP address of the TFTP server.ro DisplayString .1.2.8.1.1.5 |
swMultiCfgSendUserThe record of the user who downloaded the configuration filero DisplayString .1.2.8.1.1.6 |
swMultiCfgFileNameWhen the system is set to boot from SD card, this object displays the recorded path name of the boot configuration file.ro DisplayString .1.2.8.1.1.7 |
swMultiCfgCurrentUsedThe indicated configuration file ID of the system currently in use.ro INTEGER .1.2.8.2 |
swMultiCfgBootUpThis object indicates the configuration file ID which will take effect upon the next reboot.ro INTEGER .1.2.8.3 |
swMultiCfgCtrlTable SEQUENCE OF SwMultiCfgCtrlEntry .1.2.8.4 |
swMultiCfgCtrlEntryA list of information about multiple configuration management. SwMultiCfgCtrlEntry .1.2.8.4.1 |
swMultiCfgCtrlIDThe section ID of the configuration file.ro Enumeration .1.2.8.4.1.1 |
swMultiCfgActionsave: Save configuration to active configuration ID when the parameter is omitted.
active: Set any valid configuration as the active configuration.
delete: Removes the configuration from the flash memory. This configuration
cannot be the active or current configuration file.
apply: Loads the indicated configuration file and applies it to the system.
config-as-bootup-cfg: Configured as the boot-up configuration by the indicated configuration(ID).rw Enumeration .1.2.8.4.1.2 |
systemSeverityControlMgmt OBJECT IDENTIFIER .1.2.9 |
systemSeverityTrapControlIndicates the level of trap severity control. The system has a severity level control
and each trap should have a severity control set. When trap events occur and its severity
is higher than the system severity control level, the trap works as defined. If the event
severity is lower than the system severity control level, the event is ignored as if it
did not occur.rw AgentNotifyLevel (DLINK-ID-REC-MIB) .1.2.9.1 |
systemSeverityLogControlIndicates the level of trap severity control. The system has a severity level control and
each trap should have a severity control set. When trap events occur and its severity is
higher than the system severity control level, the trap works as defined. If the event
severity is lower than the system severity control level, the event is ignored as if
it did not occur.rw AgentNotifyLevel (DLINK-ID-REC-MIB) .1.2.9.2 |
agentTrustedHostMgmt OBJECT IDENTIFIER .1.2.10 |
agentTrustedHostTableThis table contains the trusted host information. SEQUENCE OF AgentTrustedHostEntry .1.2.10.1 |
agentTrustedHostEntryA list of information about the trusted hosts. AgentTrustedHostEntry .1.2.10.1.1 |
agentTrustedHostIndexThe index of the trusted host entry.ro INTEGER .1.2.10.1.1.1 |
agentTrustedHostIPAddressSpecifies the IP address of the trusted host.rw IpAddress .1.2.10.1.1.2 |
agentTrustedHostRowStatusIndicates the status of this entry. When creating a trusted host
entry, the IP address should also be set.rw RowStatus (SNMPv2-TC) .1.2.10.1.1.3 |
agentTrustedHostIPSubnetMaskSpecifies the IP subnet mask of the trusted host.rw IpAddress .1.2.10.1.1.4 |
agentTrustedHostForSNMPSpecifies the trusted host for SNMP.rw Enumeration .1.2.10.1.1.5 |
agentTrustedHostForTELNETSpecifies the trusted host for Telnet.rw Enumeration .1.2.10.1.1.6 |
agentTrustedHostForSSHSpecifies the trusted host for SSH.rw Enumeration .1.2.10.1.1.7 |
agentTrustedHostForHTTPSpecifies the trusted host for HTTP.rw Enumeration .1.2.10.1.1.8 |
agentTrustedHostForHTTPSSpecifies the trusted host for HTTPS.rw Enumeration .1.2.10.1.1.9 |
agentTrustedHostForPINGSpecifies the trusted host for PING.rw Enumeration .1.2.10.1.1.10 |
agentTrustedHostAddrTypeThe type of trusted host address as specified by
the 'agentTrustedHostAddr' object.rw InetAddressType (INET-ADDRESS-MIB) .1.2.10.1.1.11 |
agentTrustedHostAddrSpecifies the IP address of the trusted host.rw InetAddress (INET-ADDRESS-MIB) .1.2.10.1.1.12 |
agentTrustedHostIPv6PrefixLenSpecifies the IPv6 prefix length of the IPv6 trusted host.rw INTEGER .1.2.10.1.1.13 |
agentTrustedHostDelAllStateUsed to delete all trusted host entries.rw Enumeration .1.2.10.2 |
agentFDBMgmt OBJECT IDENTIFIER .1.2.11 |
agentFDBClearAllStateUsed to clear all FDB entries.rw Enumeration .1.2.11.1 |
agentFDBClearByPortTableUsed to clear FDB entries by port. SEQUENCE OF AgentFDBClearByPortEntry .1.2.11.2 |
agentFDBClearByPortEntryThis is an entry of the agentFDBClearByPortTable. AgentFDBClearByPortEntry .1.2.11.2.1 |
agentFDBClearPortIndexThis object indicates the port number. INTEGER .1.2.11.2.1.1 |
agentFDBClearByPortActionThis object indicates whether to clear FDB or not.rw Enumeration .1.2.11.2.1.2 |
agentFDBClearByVlanTableUsed to clear FDB entries by port. SEQUENCE OF AgentFDBClearByVlanEntry .1.2.11.3 |
agentFDBClearByVlanEntryThis is an entry of agentFDBClearByPortTable. AgentFDBClearByVlanEntry .1.2.11.3.1 |
agentFDBClearVidThis object indicates the VLAN-ID. VlanId (Q-BRIDGE-MIB) .1.2.11.3.1.1 |
agentFDBClearByVlanActionThis object indicates whether to clear the FDB or not.rw Enumeration .1.2.11.3.1.2 |
agentFDBSecurityTableUsed to display the FDB entries that have been created by the security module. SEQUENCE OF AgentFDBSecurityEntry .1.2.11.4 |
agentFDBSecurityEntryThis is an entry of agentFDBSecurityTable. AgentFDBSecurityEntry .1.2.11.4.1 |
agentFDBVidThis object indicates the VLAN-ID. VlanId (Q-BRIDGE-MIB) .1.2.11.4.1.1 |
agentFDBMacAddressThis object indicates the MAC address. MacAddress (SNMPv2-TC) .1.2.11.4.1.2 |
agentFDBPortThis object indicates the port number.ro INTEGER .1.2.11.4.1.3 |
agentFDBTypeThis object indicates the MAC address type.ro Enumeration .1.2.11.4.1.4 |
agentFDBStatusThis object indicates the MAC address's forwarding status.ro Enumeration .1.2.11.4.1.5 |
agentFDBSecurityModuleThis object is used to indicate which security module created the current MAC address.
dot1x: 802.1X.
wac: Web-based Access Control.
jwac: Web-Based Access Control extension for Japan.
port-security: Port Security.
mac-based-access-control: MAC-based Access Control.
compound-authentication: Compound Authentication.ro Enumeration .1.2.11.4.1.6 |
agentARPMgmt OBJECT IDENTIFIER .1.2.12 |
agentARPClearAllStateUsed to clear all ARP entries.rw Enumeration .1.2.12.1 |
agentGratuitousARPMgmt OBJECT IDENTIFIER .1.2.12.2 |
agentGratuitousARPSendIpifStatusUpStateThis is used to enable/disable sending of gratuitous ARP request
packets while the IPIF interface comes up. This is used to automatically
announce the interface's IP address to other nodes. By default,
the state is enabled, and only one ARP packet will be broadcast.rw Enumeration .1.2.12.2.1 |
agentGratuitousARPSendDupIpDetectedStateThis is used to enable/disable the sending of gratuitous ARP request
packets while a duplicate IP is detected. By default, the state is enabled.
The duplicate IP detected state indicates that the system has received an ARP request
packet that was sent by an IP address that matches the system's own IP address.
In this case, the system knows that somebody out there is using an IP address
that is in conflict with the system. In order to reclaim the correct host
of this IP address, the system can send out the gratuitous ARP request
packet for this duplicate IP address.rw Enumeration .1.2.12.2.2 |
agentGratuitousARPLearningStateThis is used to enable/disable learning of an ARP entry in the ARP
cache based on the received gratuitous ARP packet. If the switch
receives a gratuitous ARP request/reply packet and the sender's
IP address is in its ARP table, it should update the ARP entry.
By default, the state is disabled.rw Enumeration .1.2.12.2.3 |
agentGratuitousARPTableGratuitous ARP Table Information. SEQUENCE OF AgentGratuitousARPEntry .1.2.12.2.4 |
agentGratuitousARPEntryA list of information from the Gratuitous ARP Table. AgentGratuitousARPEntry .1.2.12.2.4.1 |
agentGratuitousARPInterfaceNameThe name of the IP interface.ro DisplayString (SNMPv2-TC) .1.2.12.2.4.1.1 |
agentGratuitousARPPeriodicalSendIntervalThis is used to configure the interval for the periodic sending of
gratuitous ARP request packets.
0 means do not send gratuitous ARP request packets periodically.rw INTEGER .1.2.12.2.4.1.2 |
agentGratuitousARPTrapStateThis indicates the state of the gratuitous ARP trap. The switch can
trap the IP conflict events to inform the administrator.
By default, the trap is disabled.rw Enumeration .1.2.12.2.4.1.3 |
agentGratuitousARPLogStateThis indicates the state of the gratuitous Log trap. The switch can
log the IP conflict events to inform the administrator.
By default, the event log is enabled.rw Enumeration .1.2.12.2.4.1.4 |
agentARPTotalARPEntriesUsed to display the total number of ARP entries.ro INTEGER .1.2.12.3 |
agentARPRetryTimesThis indicates the retry times of the ARP request.rw INTEGER .1.2.12.4 |
swMultiImageCtrlTable SEQUENCE OF SwMultiImageCtrlEntry .1.2.13 |
swMultiImageCtrlEntryA list of information about multiple image management. SwMultiImageCtrlEntry .1.2.13.1 |
swMultiImageCtrlIDThe stacking section ID of the firmware image.
The stacking section ID = 256 * Unit ID + Image File ID.ro INTEGER .1.2.13.1.1 |
swMultiImageCtrlActionThis object indicates the running status of the image which is
specified by swMultiImageCtrlID and swMultiImageCtrlUnitID.
config-as-bootup-fw (1) - Configured as the bootup firmware by the indicated firmware(ID).
delete (2) - Delete the firmware by indicated firmware ID.
none (3) - No action.rw Enumeration .1.2.13.1.2 |
agentOutOfBandDataBitsThis object indicates the out-of-band data bits.ro INTEGER .1.2.14 |
agentOutOfBandParityBitsThis object indicates the out-of-band parity bits.ro DisplayString (SNMPv2-TC) .1.2.15 |
agentOutOfBandStopBitsThis object indicates the out-of-band stop bits.ro INTEGER .1.2.16 |
agentOutOfBandAutoLogoutConfigThis object allows the user to specify an out-of-band auto logout time.rw Enumeration .1.2.17 |
agentBscFileSystemMgmt OBJECT IDENTIFIER .1.2.18 |
agentBscFileSystemTableA list of MIB File System Basic Configuration entries supported
by the file update of this agent. SEQUENCE OF AgentBscFileSystemEntry .1.2.18.1 |
agentBscFileSystemEntryA File System basic configuration entry that contains objects
describing a particular MIB supported by this agent. AgentBscFileSystemEntry .1.2.18.1.1 |
agentBscFileSystemIndexThe table index for the file entry.
This object describes the file type.
runtime-code (1),
log-file (2),
cfg-file (3),
attack-log-file (7)ro Integer32 .1.2.18.1.1.1 |
agentBscFileSystemDscrThe description of the software file purpose in this entry.ro DisplayString .1.2.18.1.1.2 |
agentBscFileSystemServerAddrThe IP address where the file to be downloaded is located, or the IP address
where the file will be uploaded to.rw IpAddress .1.2.18.1.1.3 |
agentBscFileSystemServerIPv6AddrThe IPv6 address where the file is to be downloaded from or uploaded to.rw Ipv6Address .1.2.18.1.1.4 |
agentBscFileSystemServerFileNameThe name of the file to be downloaded from or uploaded to the TFTP server.
If agentBscFileSystemDeviceFileName is not set, the switch will default to using
the bootup file as the runtime image for the switch.rw DisplayString .1.2.18.1.1.5 |
agentBscFileSystemDeviceDriverIDSpecifies the drive of the device that the firmware to be uploaded/downloaded is located.
If none (1) is specified, the switch will default to the current drive.rw Enumeration .1.2.18.1.1.6 |
agentBscFileSystemDeviceFileNameThe name of the file to be downloaded to the device, or uploaded from the
device. When downloading or uploading, the agentBscFileSystemServerFileName object must also be set.rw DisplayString .1.2.18.1.1.7 |
agentBscFileSystemLoadTypeThis object allows the user to select a download or upload function for the file.
Note:
For systems that do not support changes to this object, setting a value for
this object will cause the system to return a bad-value error message.rw Enumeration .1.2.18.1.1.8 |
agentBscFileSystemCtrlUnitIDSpecifies which unit of the switch stack the firmware image or configuration file should be downloaded from.
One or more units can be set in this list. Each bit from left to right represents the
switch from unit ID 1 to unit ID 12.
If this list is set to null it represents all stack switches.rw UnitList .1.2.18.1.1.9 |
agentBscFileSystemBootUpImageThe result of the download will depend on whether the boot_up option has been specified.
Case 1: In the case of the master unit providing the file system and the slave unit
not providing the file system, when the boot_up parameter is specified, then the file will
be downloaded to the boot_up image on the slave. If the boot_up parameter is not specified,
then the file will not be downloaded to this slave unit.
Case 2: In the case of the master unit not providing the file system and the slave unit
providing the file system, when the boot_up parameter is specified, then the file will be downloaded
to the boot_up image on the slave unit. If boot_up is not specified, then the file will
not be downloaded to this slave unit.
Case 3: In the case of the master unit and the slave unit both supporting or not supporting the
file system, the file will be downloaded to the specified file on the slave unit. If boot_up
is specified, the downloaded file will be assigned as the boot_up image.
True: boot_up option is specified.
False: boot_up option is not specified..rw TruthValue (SNMPv2-TC) .1.2.18.1.1.10 |
agentBscFileSystemForceAgreeWhen the force_agree option is specified, the reboot command will be executed immediately
without any further confirmation from the user.
True: force_agree option is specified.
False: force_agree option is not specified..rw TruthValue (SNMPv2-TC) .1.2.18.1.1.11 |
agentBscFileSystemCtrlThis object allows the user to download runtime software. The settings
will take effect when the system restarts. See Note (1) below
Note 1:
For systems which do not support value changes to this object,
setting these values will cause the system to return a bad-value error message
start (3) - activate firmware.rw Enumeration .1.2.18.1.1.12 |
agentBscFileSystemInterfaceNameThis node is used to specify the interface name when agentBscFileSystemServerIPv6Addr
is the local link address.rw DisplayString .1.2.18.1.1.13 |
agentBscFileSystemServerDomainNameThis object indicates the domain name of the TFTP server.rw DisplayString .1.2.18.1.1.14 |
agentBscFileSystemIncrementIf increment is specified, then the existing configuration will not be cleared before applying
of the new configuration. If it is not specified, then the existing configuration will be cleared
before applying of the new configuration.
True : keep valid
False : erase.rw TruthValue (SNMPv2-TC) .1.2.18.1.1.15 |
agentBscFileSystemSaveConfigDriverIDThe drive on the device that the configuration file is will be saved to.
If none (1) is specified, the switch places the file on the current drive by default.rw Enumeration .1.2.18.2 |
agentBscFileSystemSaveConfigFileNameThe name of the configuration file that will be saved to the device.
When agentBscFileSystemSaveCfg is set to cfg (2), and if the agentBscFileSystemSaveConfigFileName
is not null, the configuration file will be saved to the set file name.
If set to null, the configuration file will be saved to the boot_up CFG file.rw DisplayString .1.2.18.3 |
agentBscFileSystemSaveCfgThis indicates the method of saving information to the NV-RAM of the device.
other (1) - None of the following.
cfg (2) - Save configuration.
log (3) - Save log.
all (4) - Save both ( active configuration and log).rw Enumeration .1.2.18.4 |
agentFileSystemConfigTableThis table indicates the information about the bootup files. SEQUENCE OF AgentFileSystemConfigEntry .1.2.18.5 |
agentFileSystemConfigEntryA list of information about the bootup files for each unit of the switch stack. AgentFileSystemConfigEntry .1.2.18.5.1 |
agentFileSystemUnitThe unit ID.ro Integer32 .1.2.18.5.1.1 |
agentFileSystemDriverIDThe drive on the device that the configuration file will be saved to.
If none (1) is specified, the switch will place the file to the current drive by default.rw Enumeration .1.2.18.5.1.2 |
agentFileSystemBootImageWhen displayed, it shows the current bootup image file name.
When set, the set name will be set as the bootup image.rw DisplayString .1.2.18.5.1.3 |
agentFileSystemBootConfigWhen displayed, it shows the current bootup configuration file name.
When set, the set name will be set as the bootup configuration.rw DisplayString .1.2.18.5.1.4 |
agentFileSystemActConfigWhen displayed, it shows null.
When set, the set name will be active at once, but the set name
will not be set as the bootup configuration.rw DisplayString .1.2.18.5.1.5 |
agentRebootUsed to restart the switch.rw Enumeration .1.2.19 |
agentResetUsed to reset all switch parameters.
none (1): No action. This is the default value of this object.
config (2): All parameters are reset to default settings.
The device will neither save nor reboot.
system (3): All parameters are reset to default settings.
The switch will then do a factory reset, save, and reboot.
reset (4) : All parameters will be reset to default settings except for the
IP address, user account, and history log.
The device will neither save nor reboot.
system-exclude-vlan(5) : All parameters are reset to default settings except for VLAN.
The switch will then save its settings and reboot.
system-exclude-ip(6) : All parameters are reset to default settings except IP address.
The switch will then save its settings and reboot.
system-exclude-vlan-ip(7): All parameters are reset to default settings except VLAN and IP address.
The switch will then save its settings and reboot.rw Enumeration .1.2.20 |
agentFTPFileTableA list of the MIB Basic Config entries support files updated by this agent. SEQUENCE OF AgentFTPFileEntry .1.2.21 |
agentFTPFileEntryA basic configuration entry containing the objects describing a particular MIB
supported by this agent. AgentFTPFileEntry .1.2.21.1 |
agentFTPFileIndexThe table index for the file entry. This object describes the file type
runtime-code (1),
log-file (2),
cfg-file (3)ro Integer32 .1.2.21.1.1 |
agentFTPFileDscrThe description of the software file purpose in this entry.
Note: For systems which do not support changes to this object, setting a value for
this object will cause the system to return bad-value error messages.rw DisplayString .1.2.21.1.2 |
agentFTPFileLoadTypeThis object provides the user with a choice of uploading or downloading the selected file.
Note: For systems which do not support a change of this object, setting a value to this object
will cause the system to return bad-value error messages.rw Enumeration .1.2.21.1.3 |
agentFTPFileAddrThe IP address that the file to be downloaded is located on, or the IP address
where the file will be uploaded to.rw IpAddress .1.2.21.1.4 |
agentFTPTCPPortThe TCP port number being used to establish the command connection.rw INTEGER .1.2.21.1.5 |
agentFTPFileNameThe name of the file to be downloaded from, or uploaded to, the FTP server.rw DisplayString .1.2.21.1.6 |
agentFTPUserNameThis is the user name to enter in upload/download.rw DisplayString (SNMPv2-TC) .1.2.21.1.7 |
agentFTPPasswordThis is the password to enter for an upload/download.rw DisplayString (SNMPv2-TC) .1.2.21.1.8 |
agentFTPFileCtrlIDThe section ID of the firmware image or configuration file.
A value of 0 indicates the boot-up firmware image or configuration file.rw INTEGER .1.2.21.1.9 |
agentFTPFileBIncrementThis object indicates whether the previous configuration will remain
valid or not after downloading the configuration file.
True: Keep valid
False: Erase.rw TruthValue (SNMPv2-TC) .1.2.21.1.10 |
agentFTPFileCtrlThis object gives the user the option to download runtime software. The setting will take effect
when the system restarts. See Note (1) below
Note 1:
For systems which do not support changes to this object, setting a value for this object
will cause the system to return bad-value error messages.rw Enumeration .1.2.21.1.11 |
agentFTPFileBootUpImageThis object indicates whether to set the special file as a boot up file or not.
True: The boot-up option is specified.
False: The boot-up option is not specified.rw TruthValue (SNMPv2-TC) .1.2.21.1.12 |
agentFTPFileForceAgreeWhen the force-agree option is specified, the reboot command will be executed
immediately without any further confirmation from the user.
True: Force-agree option is specified.
False: Force-agree option is not specified.rw TruthValue (SNMPv2-TC) .1.2.21.1.13 |
agentFTPFileIPv6AddrThe IPv6 address where the file is to be downloaded from or uploaded to.rw DisplayString (SNMPv2-TC) .1.2.21.1.14 |
agentFTPFileInterfaceNameThis node is used to specify the interface name when agentFTPFileIPv6Addr
is the local link address.rw DisplayString (SNMPv2-TC) .1.2.21.1.15 |
agentFTPFileUnitIDSpecifies which unit of the switch stack the firmware image or configuration
file should be downloaded from. One or more units can be set in this list. Each
bit from left to right represents the switch from unit ID 1 to unit ID 12.If this
list is set to null it represents all stack switches.rw UnitList .1.2.21.1.16 |
agentSnmpTrapStateThis object indicates if the SNMP trap is enabled or disabled.rw Enumeration .1.2.22 |
agentOutOfBandMgmt OBJECT IDENTIFIER .1.2.23 |
agentOutOfBandMgmtStateEnables or disables the interface.rw Enumeration .1.2.23.1 |
agentOutOfBandMgmtIpAddrThe IP address for out of band management. This object can only take the
value of the unicast IP address.rw IpAddress .1.2.23.2 |
agentOutOfBandMgmtSubnetMaskThe IP net mask for out of band management.rw IpAddress .1.2.23.3 |
agentOutOfBandMgmtGatewayThe gateway for out of band management.rw IpAddress .1.2.23.4 |
agentOutOfBandMgmtLinkStatusThe current Link status for out of band management.ro Enumeration .1.2.23.5 |
agentTrapMgmt OBJECT IDENTIFIER .1.2.24 |
agentTrapColdStartWhen enabled (1), whenever the device detects a cold start event,
a trap will be sent out.rw Enumeration .1.2.24.1 |
agentTrapWarmStartWhen enabled (1), whenever the device detects a warm start event,
a trap will be sent out.rw Enumeration .1.2.24.2 |
agentTrapRmonRisingAlarmWhen enabled (1), whenever the device detects a RMON rising alarm
event , a trap will be sent out.rw Enumeration .1.2.24.3 |
agentTrapRmonFallingAlarmWhen enabled (1), whenever the device detects a RMON falling alarm
event, a trap will be sent out.rw Enumeration .1.2.24.4 |
agentTrapCfgSaveWhen enabled (1), whenever the device detects a configuration saving
completed event, a trap will be sent out.rw Enumeration .1.2.24.5 |
agentTrapCfgUploadWhen enabled (1), whenever the device detects a configuration
uploading completed event, a trap will be sent out.rw Enumeration .1.2.24.6 |
agentTrapCfgDownloadWhen enabled (1), whenever the device detects a configuration
downloading completed event, a trap will be sent outrw Enumeration .1.2.24.7 |
agentFTPFileSystemTableThe FTP management table for the file system SEQUENCE OF AgentFTPFileSystemEntry .1.2.25 |
agentFTPFileSystemEntryA File System basic configuration entry that contains objects
describing a particular MIB supported by this agent. AgentFTPFileSystemEntry .1.2.25.1 |
agentFTPFileSystemIndexThe table index for the file entry. Integer32 .1.2.25.1.1 |
agentFTPFileSystemDscrThe description of the software file purpose in this entry.ro DisplayString (SNMPv2-TC) .1.2.25.1.2 |
agentFTPFileSystemLoadTypeThis object allows the user to select a download or upload function for the file.rw Enumeration .1.2.25.1.3 |
agentFTPFileSystemAddressTypeThe address type of agentFTPFileSystemAddress.rw InetAddressType (INET-ADDRESS-MIB) .1.2.25.1.4 |
agentFTPFileSystemAddressThis object indicates the FTP server address.rw InetAddress (INET-ADDRESS-MIB) .1.2.25.1.5 |
agentFTPFileSystemTCPPortThe TCP port number being used to establish the control connection.rw INTEGER .1.2.25.1.6 |
agentFTPFileSystemServerFileNameThe name of the file to be downloaded from or uploaded to the FTP server.rw DisplayString .1.2.25.1.7 |
agentFTPFileSystemDeviceFileNameThe name of the file to be downloaded to the device, or uploaded from the
device.
If agentFTPFileSystemDeviceFileName is not set, the switch will default to
the bootup file.rw DisplayString .1.2.25.1.8 |
agentFTPFileSystemUserNameThis object indicates the user name to access the FTP server.rw DisplayString (SNMPv2-TC) .1.2.25.1.9 |
agentFTPFileSystemPasswordThis object indicates the password to access the FTP server.rw DisplayString (SNMPv2-TC) .1.2.25.1.10 |
agentFTPFileSystemCtrlUnitIDSpecifies which unit of the switch stack the firmware image or configuration
file should be downloaded from. One or more units can be set in this list. Each
bit from left to right represents the switch from unit ID 1 to unit ID 12.If this
list is set to null it represents all stack switches.rw UnitList .1.2.25.1.11 |
agentFTPFileSystemBootUpImageThis object indicates whether to set the special file as the boot up file or not.
True: The boot-up option is specified.
False: The boot-up option is not specified.rw TruthValue (SNMPv2-TC) .1.2.25.1.12 |
agentFTPFileSystemCtrlThis object allows the user to execute an FTP download/upload.rw Enumeration .1.2.25.1.13 |
agentBscCMDLogStateThis object indicates the command logging state.rw Enumeration .1.2.26 |
agentBscBroadcastPingReplyStateThis object indicates the broadcast ping reply state.rw Enumeration .1.2.27 |
agentBscTftpConfigMgmt OBJECT IDENTIFIER .1.2.28 |
agentBscTftpCfgFirmwareFileThe firmware pathname that needs to be downloaded/uploaded from/to the TFTP server.rw DisplayString .1.2.28.1 |
agentBscTftpCfgConfigFileThe configuration pathname that needs to be downloaded/uploaded from/to the TFTP server.rw DisplayString .1.2.28.2 |
agentBscTftpCfgLogFileThe log pathname that needs to be uploaded to the TFTP server.rw DisplayString .1.2.28.3 |
agentBscTftpCfgAttackLogFileThe attack log pathname that needs to be uploaded to the TFTP server.rw DisplayString .1.2.28.4 |
agentBscTftpCfgCertificateFileThe certificate pathname that needs to be downloaded from the TFTP server.rw DisplayString .1.2.28.5 |
agentBscTftpCfgKeyFileThe key pathname that needs to be downloaded from the TFTP server.rw DisplayString .1.2.28.6 |
agentBscTftpCfgTechSuooprtFileThe technique's support information pathname that needs to be uploaded to the TFTP server.rw DisplayString .1.2.28.7 |
agentBscTftpCfgDebugLogFileThe debug log pathname that needs to be uploaded to the TFTP server.rw DisplayString .1.2.28.8 |
agentBscTftpCfgSIMFirmwareFileThe firmware pathname that needs to be downloaded/uploaded from/to the TFTP server when it is SIM enabled.rw DisplayString .1.2.28.9 |
agentBscTftpCfgSIMConfigFileThe configuration pathname that needs to be downloaded/uploaded from/to the TFTP server when it is SIM enabled.rw DisplayString .1.2.28.10 |
agentBscTftpCfgSIMLogFileThe log pathname that needs to be uploaded to the TFTP server when it is SIM enabled.rw DisplayString .1.2.28.11 |
agentBscTftpCfgServerIPAddrThe IPv4 address of the TFTP server.rw IpAddress .1.2.28.12 |
agentBscTftpCfgServerIPv6AddrThe IPv6 address of the TFTP server.rw Ipv6Address .1.2.28.13 |
agentBscTftpCfgServerDomainNameThe domain name of the TFTP server.rw DisplayString .1.2.28.14 |
agentBscCommunityEncryptionStateThis object indicates the encryption state on the SNMP community string.rw Enumeration .1.2.29 |
agentIpProtoConfig OBJECT IDENTIFIER .1.3 |
agentIpNumOfIfThe total number of IP interfaces supported by this agent.ro Integer32 .1.3.1 |
agentIpTftpServerAddrThe IP address of the TFTP Server.rwobsolete IpAddress .1.3.2 |
agentIpGetIpFromThis object indicates if the agent will get its system IP address
from a Bootp/DHCP server at start up.rw Enumeration .1.3.3 |
agentIpAutoconfigIndicates the status of automatically getting the configuration information
from a TFTP server connected to the device.rw Enumeration .1.3.4 |
agentIpAutoconfigTimeoutThis timer is used to limit the length of time for getting the configuration
information from a TFTP server connected to the device.rw Integer32 .1.3.5 |
agentIpTrapManager OBJECT IDENTIFIER .1.4 |
agentTrapManagerTableA list of trap managers that the SNMP traps will be sent to. SEQUENCE OF AgentTrapManagerEntry .1.4.2 |
agentTrapManagerEntryEach entry contains the particular trap manager's settings. AgentTrapManagerEntry .1.4.2.1 |
agentTrapManagerIndexA value that uniquely identifies trapDestEntry. INTEGER .1.4.2.1.1 |
agentTrapManagerIpAddrThe destination IP address for SNMP traps.rw IpAddress .1.4.2.1.2 |
agentTrapManagerCommThe community string used to encode SNMP trap packets being sent to the trap
manager.rw DisplayString .1.4.2.1.3 |
agentTrapManagerMsgVerThis object indicates the version of trap packets that will be sent to
this trap manager. The default setting is SNMP Agent Version Dependent.
Note:
Because some of these functions will be limited by the support of
the system in question, some selected items may be invalid. If one
of these items is selected, a bad value error message will prompt
the user.rw Enumeration .1.4.2.1.4 |
agentTrapManagerStatusThis object indicates whether or not the trap should be sent to
the trap manager.rw Enumeration .1.4.2.1.5 |
agentNotify OBJECT IDENTIFIER .1.7 |
agentNotifMgmt OBJECT IDENTIFIER .1.7.1 |
notifFirmwareMgmt OBJECT IDENTIFIER .1.7.1.2 |
agentNotifFirmware OBJECT IDENTIFIER .1.7.2 |
agentNotifyPrefix OBJECT IDENTIFIER .1.7.2.0 |
agentsystemRestartThis trap contains the reboot information. NOTIFICATION-TYPE .1.7.2.0.1 |
agentSaveToNVRAMThis trap is sent whenever all the device configuration has been saved to NV-RAM. NOTIFICATION-TYPE .1.7.2.0.2 |
agentFileTransferStatusChangeFile transfer status change notification. NOTIFICATION-TYPE .1.7.2.0.3 |
agentSetToFactoryDefaultThis trap is sent whenever the 'set to factory default' setting has been processed. NOTIFICATION-TYPE .1.7.2.0.4 |
agentGratuitousARPTrapThis trap is sent when there is an IP address conflict. NOTIFICATION-TYPE .1.7.2.0.5 |
agentLoginFailTrapThe trap is sent when a login has failed through one of the login types (console, Telnet, web, SSL or SSH). NOTIFICATION-TYPE .1.7.2.0.6 |
agentFirmwareUpgradeThis trap is sent when the process of upgrading the firmware via SNMP has finished. NOTIFICATION-TYPE .1.7.2.0.7 |
agentAccessFlashFailedThe trap is sent when access to the flash fails. NOTIFICATION-TYPE .1.7.2.0.8 |
agentCfgOperCompleteTrapThe trap is sent when the configuration is completely saved, uploaded
or downloaded. NOTIFICATION-TYPE .1.7.2.0.9 |
notificationBindings OBJECT IDENTIFIER .1.7.2.1 |
unitIDThe unit ID of the device which triggered the event.ro INTEGER .1.7.2.1.1 |
trapInfosystemRestartThis object indicates the last time the device rebooted.ro DisplayString .1.7.2.1.2 |
agentGratuitousARPIpAddrA duplicate IP address with the switch already exists.ro IpAddress .1.7.2.1.3 |
agentGratuitousARPMacAddrThis object is the MAC address of the device which has the duplicate IP address.ro MacAddress (SNMPv2-TC) .1.7.2.1.4 |
agentGratuitousARPPortNumberThis indicates the portNum with a string.
For example, if the device is in standalone mode, and the port
number is 23, the string should be 23.
If the device is in stacking mode, and the unit ID is 2, and the
port number is 3, the string should be 2:3.ro DisplayString (SNMPv2-TC) .1.7.2.1.5 |
agentLoginTypeThe type is the user login method type.ro Enumeration .1.7.2.1.6 |
agentLoginAAAMethodThis method is the AAA login method.ro Enumeration .1.7.2.1.7 |
agentLoginUserNameThis object is the name of the user that failed to login to the switch.ro DisplayString (SNMPv2-TC) .1.7.2.1.8 |
agentLoginIpAddrThis object is the login type from the IP address.ro IpAddress .1.7.2.1.9 |
agentLoginMacAddrThis object is the login type from a MAC address.ro MacAddress (SNMPv2-TC) .1.7.2.1.10 |
agentLoginAAAServerAddrThis object is the login type through a console authenticated by an AAA server.ro IpAddress .1.7.2.1.11 |
agentLoginFailInfoThis object indicates the reason for the login failure.ro Enumeration .1.7.2.1.12 |
agentAccessFlashOperThis object indicates the operation of the access flash failure.ro DisplayString .1.7.2.1.13 |
agentAccessFlashAddrThis object indicates the address of the access flash failure.ro INTEGER .1.7.2.1.14 |
agentCfgOperateThis object indicates the operation type of the configuration.ro Enumeration .1.7.2.1.15 |