ADSLF-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ADSLF-MIB.
81
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
81 total| Object Name |
|---|
RFC1155-SMISpecifies the ADSL coding type used on this line.
Other types may be added in the future with higher values ala ifIANAtype.
This is used to create a LCS sub-MIB in the same way ifIANAtype adsl(94)
is used to create this MIB.ro Enumeration .1.3.6.1.4.1.429.4.32.1 |
adslLineTypethis describes which other tables go with this ifEntry.
use EITHER three separate ifEntries (and adslLinEntries):
(1) and tables 1,2,3, 6,7,8,9
(2) with 1,4,5, and (3) and 1,4,5,
OR
use values (4) or (5) with tables 1-9 as a single ifEntry/adslLineEntryro Enumeration .1.3.6.1.4.1.429.4.32.2 |
adslLineSpecificOID instance in vendor-specific MIB. The Instance may be
used to determine shelf/slot/port of the ATU-C interface
in a DSLAM (among other possibilities)ro OBJECT IDENTIFIER .1.3.6.1.4.1.429.4.32.3 |
adslLineStatusStatus indicates mandatory state of the line.
This is a bit-map of possible conditions.
These are from the perspective of the ATU-C, since any loss of
communication with the ATU-R prevents determination of its state.
This is intended to supplement ifOperStatus and ifAdminStatus.ro Enumeration .1.3.6.1.4.1.429.4.32.4 |
adslAturInvSerialNumberVendor specific Serial number of the ATU-C modemro DisplayString .1.3.6.1.4.1.429.4.32.5 |
adslAturInvVendorIDThe vendor ID assigned by T1E1.4 according to its Appendix D.ro INTEGER .1.3.6.1.4.1.429.4.32.6 |
adslAturCurrOutputPowerCurrent output powerro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.7 |
adslAturCurrTransmitRateCurrent transmit rate in kbps, limited to multiples of 32kbpsro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.8 |
adslAturCurrCodeWordLengthCurrent Code Word Length,
calculated from Transmit rate and noise marginro INTEGER .1.3.6.1.4.1.429.4.32.9 |
adslAturCurrSnrMgnto be supplied.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.10 |
adslAturCurrAtnto be supplied.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.11 |
adslAturCurrReceiveGainto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.12 |
adslAturPerfValidIntervalsnumber of valid intervals in the adslAturPerfDataTablero INTEGER .1.3.6.1.4.1.429.4.32.13 |
adslAturPerfLofcount of the number of Loss of Framing events since system reset.ro INTEGER .1.3.6.1.4.1.429.4.32.14 |
adslAturPerfLoscount of the number of Loss of Signal events since system reset.ro INTEGER .1.3.6.1.4.1.429.4.32.15 |
adslAturPerfLprcount of the number of Loss of Power events since system reset.ro INTEGER .1.3.6.1.4.1.429.4.32.16 |
adslAturPerfCVcount of the number of Loss of Coding Violation events since system reset.ro INTEGER .1.3.6.1.4.1.429.4.32.17 |
adslAturPerfEScount of the number of Errored Seconds since system reset.ro INTEGER .1.3.6.1.4.1.429.4.32.18 |
adslAturPerfCurr1DayElapSecsThe total time interval over which all Curr1Day interval counters are measured.
If 0, this interval is invalid.ro INTEGER .1.3.6.1.4.1.429.4.32.19 |
adslAturPerfCurr1DayMoniSecsThe total number of valid seconds in the Curr1Day interval counters.
This may be less than adslAturPerfCurr1DayElapSecs only when
there were some seconds in the interval when no valid data
could be collected.ro INTEGER .1.3.6.1.4.1.429.4.32.20 |
adslAturPerfPrev1DayElapSecsThe total time interval over which all Prev1Day interval counters are measured.
If 0, this interval is invalid.ro INTEGER .1.3.6.1.4.1.429.4.32.21 |
adslAturPerfPrev1DayMoniSecsThe total number of valid seconds in the Prev1Day interval counters.
This may be less than adslAturPerfPrev1DayElapSecs only when
there were some seconds in the interval when no valid data
could be collected.ro INTEGER .1.3.6.1.4.1.429.4.32.22 |
adslAturPerfCurr1DayLofsCount of the number of seconds when there was Loss of Framing
during the mandatory day, as measured by adslAturPerfCurr1DayElapSecs.ro INTEGER .1.3.6.1.4.1.429.4.32.23 |
adslAturPerfPrev1DayLofsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.24 |
adslAturPerfCurr1DayLossto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.25 |
adslAturPerfPrev1DayLossto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.26 |
adslAturPerfCurr1DayLprsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.27 |
adslAturPerfPrev1DayLprsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.28 |
adslAturPerfCurr1DayCVsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.29 |
adslAturPerfPrev1DayCVsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.30 |
adslAturPerfCurr1DayESto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.31 |
adslAturPerfPrev1DayESto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.32 |
adslAturPerfCurr15minLofsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.33 |
adslAturPerfPrev15minLofsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.34 |
adslAturPerfCurr15minLossto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.35 |
adslAturPerfPrev15minLossto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.36 |
adslAturPerfCurr15minLprsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.37 |
adslAturPerfPrev15minLprsto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.38 |
adslAturPerfCurr15minESto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.39 |
adslAturPerfPrev15minESto be supplied.ro INTEGER .1.3.6.1.4.1.429.4.32.40 |
adslAturThresh15MinLofsto be supplied.rw INTEGER .1.3.6.1.4.1.429.4.32.41 |
adslAturThresh15MinLossto be supplied.rw INTEGER .1.3.6.1.4.1.429.4.32.42 |
adslAturThresh15MinLprsto be supplied.rw INTEGER .1.3.6.1.4.1.429.4.32.43 |
adslAturThresh15MinCVsto be supplied.rw INTEGER .1.3.6.1.4.1.429.4.32.44 |
adslAturThresh15MinESto be supplied.rw INTEGER .1.3.6.1.4.1.429.4.32.45 |
adslAturInitFailureTrapEnablevalues as aboverw Enumeration .1.3.6.1.4.1.429.4.32.46 |
adslAturChanCurrTxRatederived from adslAturConfMinTxRate + <available excess bandwidth> * (adslAturConfRateChanRatio / 100)
as long as it is < adslAturChanConfMaxTxRatero INTEGER .1.3.6.1.4.1.429.4.32.47 |
adslAturChanPrevTxRateThe rate that was set at the previous adslAturRateChangeTrap event.
It is also set at initialization to prevent a trap being sent.
Small rate changes are accumulated until either the rate changes by
adslAturChanConfDownDeltaRate or adslAturChanConfUpDeltaRate.ro INTEGER .1.3.6.1.4.1.429.4.32.48 |
adslAturChanReceivedBlockscount of all encoded blocks received on this channel.ro Counter .1.3.6.1.4.1.429.4.32.49 |
adslAturChanTransmittedBlockscount of all encoded blocks transmitted on this channel.ro Counter .1.3.6.1.4.1.429.4.32.50 |
adslAturChanCorrectedBlockscount of all blocks received with errors that were corrected.
These blocks are passed on as good data.ro Counter .1.3.6.1.4.1.429.4.32.51 |
adslAturChanUncorrectableBlockscount of all blocks received with uncorrectable errors.
These blocks are dropped from the received data stream.ro Counter .1.3.6.1.4.1.429.4.32.52 |
usrAdslCFMStatusFlagThis variable controls saving and loading of configuration
information for the ADSL WAN Driver. The value can be set
to either save or load by a management station. The other
values indicate if any configuration operation and what type
is in progress.rw UsrConfigStatus .1.3.6.1.4.1.429.4.32.53 |
usrAdslCfgFileNameThe name of a ConfigFile to read/write the ADSL parameters.
If the value of this object is an empty string, then the
ADSL Driver uses the default name `@file://adsl.cfg'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.54 |
usrAdslResetStatusThe Reset Status of the ADSL Starlet chipsetrw INTEGER .1.3.6.1.4.1.429.4.32.55 |
usrAdslActualBaudDataRateDwnActual Downstream Baud Ratero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.56 |
usrAdslFwRelFirmware release number of the GTI supplied transceiver
software module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.57 |
usrAdslAdiVersonValue is a number that corresponds to the version number of
the ADI chipset.ro INTEGER .1.3.6.1.4.1.429.4.32.58 |
usrAdslLocalReqDwnConstStatusValue corresponds to the local downstream constellation
requested.rw Enumeration .1.3.6.1.4.1.429.4.32.59 |
usrAdslActualUpConstStatusValue corresponds to the actual upstream constellation
that was used, which may differ from the value requested.ro Enumeration .1.3.6.1.4.1.429.4.32.60 |
usrAdslRemoteReqUpConstStatusValue corresponds to the remote requested downstream constellation
requested.ro Enumeration .1.3.6.1.4.1.429.4.32.62 |
usrAdslStartletVersonValue is a number that corresponds to the version number of
the STARLET VLSI in the transceiver.ro INTEGER .1.3.6.1.4.1.429.4.32.63 |
usrAdslActualDwnConstStatusValue corresponds to the actual downstream constellation
that was used, which may differ from the value requested.ro Enumeration .1.3.6.1.4.1.429.4.32.64 |
usrAdslLocalReqUpConstStatusValue corresponds to the local upstream constellation
requested.rw Enumeration .1.3.6.1.4.1.429.4.32.65 |
usrAdslRemoteReqDwnConstStatusValue corresponds to the remote downstream constellation
requested.ro Enumeration .1.3.6.1.4.1.429.4.32.66 |
usrAdslLocalReqBaudDataRateDwnLocal Downstream Baud Rate requested by the User.rw Enumeration .1.3.6.1.4.1.429.4.32.67 |
usrAdslFixBitStatusFixed Bit Rate feature status.rw Enumeration .1.3.6.1.4.1.429.4.32.68 |
usrAdslLocalReqXmitPowerTransmit power requested at the local ADSL transceiver represented i n dB.rw Enumeration .1.3.6.1.4.1.429.4.32.69 |
usrAdslRemoteProtocolTypeProtocol type in use by the remote RTU.ro Enumeration .1.3.6.1.4.1.429.4.32.70 |
usrAdslMeanSqErrorReceived signal to noise ratio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.71 |
usrAdslLocalActualXmitPowerTransmit power of the local ADSL transceiver represented in dB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.72 |
usrAdslOverFlowCounterRunning counter for when usrAdslBytesErrorCorrected or
usrAdslBytesNotErrorCorrected overflows. This Number is reset
to zero each time the Transceiver transitions from Idle Mode to Data Mode.ro Counter .1.3.6.1.4.1.429.4.32.73 |
usrAdslLastFailedStatusDefines the last detailed state reached in
usrAdslStartupProgress before startup failed.ro Enumeration .1.3.6.1.4.1.429.4.32.74 |
usrAdslBytesNotErrCorrectedNumber of bytes not corrected by Reed-Solomon error correction
algorithm in the STARLET.This Number is reset to zero each
time the Transceiver transitions from Idle Mode to Data
Mode.ro Counter .1.3.6.1.4.1.429.4.32.75 |
usrAdslOpStateDefines the high level operating state of the transceiver.
Used by the customer to determine whether the transceiver
is in idle mode or data mode.ro Enumeration .1.3.6.1.4.1.429.4.32.76 |
usrAdslBytesErrCorrectedNumber of bytes corrected by Reed-Solomon error correction
algorithm in the STARLET.This Number is reset to zero each
time the Transceiver transitions from Idle Mode to Data Mode.ro Counter .1.3.6.1.4.1.429.4.32.77 |
usrAdslLocalProtocolTypeProtocol type in use by the local RTU.ro Enumeration .1.3.6.1.4.1.429.4.32.78 |
usrAdslLastFailedErrorValueDefines the last detailed value reached in
usrAdslStartupProgress before startup failed.ro INTEGER .1.3.6.1.4.1.429.4.32.79 |
usrAdslLocalReceiverGainTotal local receiver gain measured in dB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.429.4.32.81 |
usrAdslSwitchTypeDSLAM switch type.rw Enumeration .1.3.6.1.4.1.429.4.32.82 |
usrAdslRemoteReqBaudDataRateDwnRemote Downstream Baud Rate requested by the User.ro Enumeration .1.3.6.1.4.1.429.4.32.90 |