Home/Catalog/ZTE-AN-OPTICAL-MODULE-MIB

ZTE-AN-OPTICAL-MODULE-MIB

AI MIB Summary

The ZTE-AN-OPTICAL-MODULE-MIB enables SNMP-based monitoring of optical transceiver parameters, including signal power, temperature, and bias current, on ZTE Access Node hardware. This module facilitates the tracking of optical module health and performance metrics to support fault detection and link integrity verification in the access network.

This MIB defines zte Access Node managed objects.
Main OID:
zxAnOpticalModuleMib.1.3.6.1.4.1.3902.1082.30.40
114
Objects
Active
Status
4
Dependencies

Imported Objects

SNMPv2-TC
SNMPv2-SMI
IF-MIB
ZTE-AN-SMI

Objects

114 total
Object Name
zxAnOpticalModuleMibThis MIB defines zte Access Node managed objects.
MODULE-IDENTITY
.1.3.6.1.4.1.3902.1082.30.40
zxAnOpticalModuleGlobalObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.3902.1082.30.40.1
zxAnOpticalModuleCapabilitiesThe optical module management capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment. opticalModuleConfClass (0): value 1 means zxAnOpticalModuleConfClass is supported. opticalAlarmPrfUnit(1): value 1 means some objects in the zxAnOpticalModuleAlmPrfTable will use the new unit, for more information, please see the description of the object in the zxAnOpticalModuleAlmPrfTable. opticalModuleConfTechNorms(2): value 1 means zxAnOpticalModuleConfTechNorms is supported. NOTE: No recommended to display it in NMS.ro
Bits
.1.3.6.1.4.1.3902.1082.30.40.1.1
zxAnOptModuleIfShutdownUnplugEnIndicates whether the zxAnOpticalModuleUnpluggedAlm should be generated when the port the optical module plugged in has been shutdown. enabled(1) : The zxAnOpticalOfflineTrapEnable indicates whether the zxAnOpticalModuleUnpluggedAlm should be generated or not. disabled(2): The zxAnOpticalModuleUnpluggedAlm should not be generated.rw
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.1.2
zxAnOptModuleFstUnpluggedRptEnIndicates whether the zxAnOpticalModuleUnpluggedAlm should be generated when the agent has detected the optical module is offline for the first time.rw
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.1.3
zxAnOpticalModuleObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.3902.1082.30.40.2
zxAnOpticalModuleAlmPrfTableThis table includes the optical module threshold profile.
SEQUENCE OF ZxAnOpticalModuleAlmPrfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.2
zxAnOpticalModuleAlmPrfEntryAn entry in zxAnOpticalModuleAlmPrfTable.
ZxAnOpticalModuleAlmPrfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.2.1
zxAnOpticalModuleAlmPrfNameA textual string containing information about the optical module alarm threshold profile name .
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.1
zxAnOpticalRxPwrLowerThreshThe lower limit threshold on input optical power. The alarm should be generated when zxAnOpticalIfRxPwrCurrValue is lower than this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.rw
Integer32 UNITS "1dBm"
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.2
zxAnOpticalRxPwrUpperThreshThe upper limit threshold on input optical power. The alarm should be generated when zxAnOpticalIfRxPwrCurrValue exceeds this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.rw
Integer32 UNITS "1dBm"
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.3
zxAnOpticalTxPwrLowerThreshThe lower limit threshold on output optical power. The alarm should be generated when zxAnOpticalIfTxPwrCurrValue is lower than this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.rw
Integer32 UNITS "1dBm"
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.4
zxAnOpticalTxPwrUpperThreshThe upper limit threshold on output optical power. The alarm should be generated when zxAnOpticalIfTxPwrCurrValue exceeds this threshold. The unit is 1dBm when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1dBm.rw
Integer32 UNITS "1dBm"
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.5
zxAnOpticalBiasCurrLowerThreshThe lower limit threshold on optical modules bias current.The alarm should be generated when zxAnOpticalBiasCurrent is lower than this threshold. The unit is 1mA when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1mA.rw
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.6
zxAnOpticalBiasCurrUpperThreshThe upper limit threshold on optical modules bias current. The alarm should be generated when zxAnOpticalBiasCurrent exceeds this threshold. The unit is 1mA when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1mA.rw
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.7
zxAnOpticalVoltageLowerThreshThe lower limit threshold on optical modules supply voltage. The alarm should be generated when zxAnOpticalSupplyVoltage is lower than this threshold. The unit is 1 Volt when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1 Volt.rw
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.8
zxAnOpticalVoltageUpperThreshThe upper limit threshold on optical modules supply voltage. The alarm should be generated when zxAnOpticalSupplyVoltage exceeds this threshold. The unit is 1 Volt when the value of opticalAlarmPrfUnit(1) is 1, otherwise the unit is 0.1 Volt.rw
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.9
zxAnOpticalTempLowerThreshThe lower limit threshold on optical modules temperature. The alarm should be generated when zxAnOpticalTemperature is lower than this threshold.rw
Integer32(-50..100) UNITS "Centigrade"
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.10
zxAnOpticalTempUpperThreshThe upper limit threshold on optical modules temperature. The alarm should be generated when zxAnOpticalTemperature exceeds this threshold.rw
Integer32(-50..100) UNITS "Centigrade"
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.11
zxAnOpticalOfflineTrapEnableIndicates whether optical module is online/offline traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disabled(2) otherwise.rw
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.12
zxAnOpticalModuleConfClassThe optical module configured class.rw
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.13
zxAnOpticalModuleAlmPrfRowStatusThe row status of this entry.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.3902.1082.30.40.2.2.1.50
zxAnOpticalAlmPrfIfConfTableThis table includes the optical module profile configuration.
SEQUENCE OF ZxAnOpticalAlmPrfIfConfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.3
zxAnOpticalAlmPrfIfConfEntryAn entry in zxAnOpticalAlmPrfIfConfTable.
ZxAnOpticalAlmPrfIfConfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.3.1
zxAnOpticalIfAlmPrfA textual string containing information about the optical module alarm threshold profile name .rw
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.3.1.2
zxAnOpticalModuleInfoTableThis table includes the optical module information.
SEQUENCE OF ZxAnOpticalModuleInfoEntry
.1.3.6.1.4.1.3902.1082.30.40.2.4
zxAnOpticalModuleInfoEntryAn entry in zxAnOpticalModuleInfoTable.
ZxAnOpticalModuleInfoEntry
.1.3.6.1.4.1.3902.1082.30.40.2.4.1
zxAnOpticalIfRxPwrCurrValueThe optical power monitored at the input.ro
Integer32 UNITS "0.001dBm"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.2
zxAnOpticalIfTxPwrCurrValueThe optical power monitored at the output.ro
Integer32 UNITS "0.001dBm"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.3
zxAnOpticalIfRateThe optical module interface rate.ro
Integer32 UNITS "0.1Gbps"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.4
zxAnOpticalBiasCurrentThe optical module bias current .ro
Integer32 UNITS "0.001mA"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.5
zxAnOpticalSupplyVoltageThe optical module supply voltage.ro
Integer32 UNITS "0.001 Volts"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.6
zxAnOpticalWavelengthThe optical module wavelength.ro
Integer32 UNITS "nm"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.7
zxAnOpticalTemperatureThe optical module temperature .ro
Integer32 UNITS "0.001Degrees"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.8
zxAnOpticalFiberTypeThe optical module Fiber Type.ro
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.9
zxAnOpticalVersionLevelThe optical module vendor Level.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.10
zxAnOpticalVendorPnThe optical module vendor P/N.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.11
zxAnOpticalVendorNameThe optical module vendor name.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.12
zxAnOpticalVendorSnThe optical module vendor sn.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.13
zxAnOpticalProductionDateThe optical module production date.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.14
zxAnOpticalModuleTypeThe optical module type.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.15
zxAnOpticalFiberInterfaceTypeThe optical fiber interface.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.16
zxAnOpticalMaterialNumberThe material number of pin(A2).ro
OCTET STRING
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.17
zxAnOpticalRegisterDataThe optical module data is from register.ro
OCTET STRING
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.18
zxAnOpticalOtdrSupportThe OTDR is supported by the optical module or not. supported(1): The optical module supports OTDR. unsupported(2): The optical module doesn't support OTDR. unknown(255): Whether the optical module supports OTDR is unknown.ro
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.19
zxAnOpticalModuleActualClassThe optical module actual class.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.20
zxAnOpticalOtdrVersionThe optical module OTDR software version. If the optical module doesn't support OTDR or the OTDR has no software version, this object will be set to an empty string.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.21
zxAnOpticalTransDistanceSmLongRThis value specifies the transfer distance that is supported by the transceiver while operating in compliance with the applicable standards using single mode based long reach fiber. The value is in units of kilometers. A value of 255 means the transceiver supports a transfer distance greater than 254 km. A value of zero means the transceiver does not support single mode fiber or that the transfer distance information must be determined from the transceiver technology.ro
Integer32 UNITS "km"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.40
zxAnOpticalTransDistanceSmShortRThis value specifies the transfer distance that is supported by the transceiver while operating in compliance with the applicable standards using single mode based short reach fiber. The value is in units of 100 meters. A value of 255 means the transceiver supports a transfer distance greater than 25.4 km. A value of zero means the transceiver does not support single mode fiber or that the transfer distance information must be determined from the transceiver technology.ro
Integer32 UNITS "100m"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.41
zxAnOpticalTransDistanceOm1This value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using 62.5 micron multimode OM1(200 MHz*km at 850nm, 500MHz*km at 1310mm) fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a transfer distance greater than 2.54km. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the transfer distance must determined from the transceiver technology.ro
Integer32 UNITS "10m"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.42
zxAnOpticalTransDistanceOm2This value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using 50 micron multimode OM2(500 MHz*km at 850nm) fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a transfer distance greater than 2.54km. A value of zero means that the transceiver does not support OM2 fiber or the transfer distance must determined from the transceiver technology.ro
Integer32 UNITS "10m"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.43
zxAnOpticalTransDistanceOm3This value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using 50 micron multimode OM3(2000 MHz*km) fiber. The value is in units of 10 meters. A value of 255 means that the transceiver supports a transfer distance greater than 2.54km. A value of zero means that the transceiver does not support OM3 fiber or the transfer distance must determined from the transceiver technology.ro
Integer32 UNITS "10m"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.44
zxAnOpticalTransDistanceCopperThis value specifies the transfer distance that is supported by the transceiver wihle operating in compliance with applicable standards using copper cable. For active cable, this value represents actual length. The value is in units of 1 meter. A value of 255 means that the transceiver supports a transfer distance greater than 254m. A value of zero means that the transceiver does not support copper or active cables or the transfer distance must determined from the transceiver technology.ro
Integer32 UNITS "m"
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.45
zxAnOpticalPartNumberThe optical module part number.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.4.1.48
zxAnOpticalAlsIfConfTableThis table includes the ALS configuration of the optical module.
SEQUENCE OF ZxAnOpticalAlsIfConfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.5
zxAnOpticalAlsIfConfEntryAn entry in zxAnOpticalAlsIfConfTable.
ZxAnOpticalAlsIfConfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.5.1
zxAnOptAlsEnableEnable or disable the ALS function.rw
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.2.5.1.1
zxAnOptAlsLaserLosDurationThis attribute specifies the value of the LOS duration. The laser will be shutdown when detected the LOS duration longer than zxAnOptAlsLaserLosDuration value. Setting this object will enable the ALS function. For C300 Series NE, the default value is 5. For C600 Series NE, the default value is 50.rw
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.5.1.2
zxAnOptAlsLaserShutdownDurationThis attribute specifies the value of the laser shutdown duration. Setting this object will enable the ALS function.rw
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.5.1.3
zxAnOptAlsLaserStartUpDurationThis attribute specifies the value of the laser re-open duration. Setting this object will enable the ALS function.rw
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.5.1.4
zxAnOpticalModuleConfTableThis table includes the optical module configuration.
SEQUENCE OF ZxAnOpticalModuleConfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.6
zxAnOpticalModuleConfEntryAn entry in zxAnOpticalModuleConfTable.
ZxAnOpticalModuleConfEntry
.1.3.6.1.4.1.3902.1082.30.40.2.6.1
zxAnOpticalModuleConfVendorNameThe optical module vendor name.
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.6.1.1
zxAnOpticalModuleConfVendorPnThe optical module vendor P/N.
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.6.1.2
zxAnOpticalModuleConfiguredClassThe optical module configured class. Includes the following: GPON/B+, GPON/C+, GPON/EC+, XGPON1/N1, XGPON1/N2a, EPON/PX20+, 10G-EPON/PRX30, 10G-EPON/PR30, GPON/D, XGS-PON/N1, XGS-PON/N2, XG-PON&GPON_COMBO/N1-B+, XG-PON&GPON_COMB0/N2-C+, GPON-OTDR/C+.rw
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.6.1.3
zxAnOpticalModuleConfPropertyThe property of the table record. default: the default record, it can't be modified or deleted by the user. userDefined: the user-defined record.rw
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.2.6.1.4
zxAnOpticalModuleConfTechNormsThe optical module configured technical norms.rw
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.6.1.11
zxAnOpticalModuleConfRowStatusThe status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the rule described in zxAnLacpAggEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.3902.1082.30.40.2.6.1.50
zxAnOpticalModuleChanInfoTableThis table includes the optical module channel information.
SEQUENCE OF ZxAnOpticalModuleChanInfoEntry
.1.3.6.1.4.1.3902.1082.30.40.2.10
zxAnOpticalModuleChanInfoEntryAn entry in zxAnOpticalModuleChanInfoTable.
ZxAnOpticalModuleChanInfoEntry
.1.3.6.1.4.1.3902.1082.30.40.2.10.1
zxAnOpticalChanLaserSwitchEnables or disables the laser function of the optical module channel.rw
Enumeration
.1.3.6.1.4.1.3902.1082.30.40.2.10.1.1
zxAnOpticalChanWavelengthThe wavelength of the optical module channel.ro
Integer32 UNITS "0.01nm"
.1.3.6.1.4.1.3902.1082.30.40.2.10.1.2
zxAnOpticalChanCurrTxPwrThe transmitted power of the optical module channel.ro
Integer32 UNITS "0.001dBm"
.1.3.6.1.4.1.3902.1082.30.40.2.10.1.3
zxAnOpticalChanBiasCurrentThe bias current of the optical module channel.ro
Integer32 UNITS "0.001mA"
.1.3.6.1.4.1.3902.1082.30.40.2.10.1.4
zxAnOpticalModuleClassValueTableThis table includes the optical module class value. NOTE: No recommended to develop this function in EMS.
SEQUENCE OF ZxAnOpticalModuleClassValueEntry
.1.3.6.1.4.1.3902.1082.30.40.2.20
zxAnOpticalModuleClassValueEntryAn entry in zxAnOpticalModuleClassValueTable.
ZxAnOpticalModuleClassValueEntry
.1.3.6.1.4.1.3902.1082.30.40.2.20.1
zxAnOpticalModuleClassIdThe optical module class id.
Integer32
.1.3.6.1.4.1.3902.1082.30.40.2.20.1.1
zxAnOpticalModuleClassValueThe optical module class value.ro
DisplayString
.1.3.6.1.4.1.3902.1082.30.40.2.20.1.2
zxAnOpticalModuleNotifications
OBJECT IDENTIFIER
.1.3.6.1.4.1.3902.1082.30.40.3
zxAnOptRxPwrUnderThreshAlmIt indicates that zxAnOpticalIfRxPwrCurrValue is below the zxAnOpticalRxPwrLowerThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.1
zxAnOptRxPwrUnderThreshClrzxAnOptRxPwrUnderThreshAlm clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.2
zxAnOptRxPwrOverThreshAlmIt indicates that zxAnOpticalIfRxPwrCurrValue is exceeds the zxAnOpticalRxPwrUpperThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.3
zxAnOptRxPwrOverThreshClrzxAnOptPwrRxOverThreshAlarm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.4
zxAnOptTxPwrUnderThreshAlmIt indicates that zxAnOpticalIfTxPwrCurrValue is below the zxAnOpticalTxPwrLowerThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.5
zxAnOptTxPwrUnderThreshClrzxAnOptPwrTxUnderThreshAlarm clear
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.6
zxAnOptTxPwrOverThreshAlmIt indicates that zxAnOpticalIfTxPwrCurrValue is exceeds the zxAnOpticalTxPwrUpperThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.7
zxAnOptTxPwrOverThreshClrzxAnOptPwrTxOverThreshAlarm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.8
zxAnOptBiasCurrUnderThreshAlmIt indicates that zxAnOpticalBiasCurrent is below the zxAnOpticalBiasCurrLowerThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.9
zxAnOptBiasCurrUnderThreshClrzxAnOptBiasCurrUnderThreshAlm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.10
zxAnOptBiasCurrOverThreshAlmIt indicates that zxAnOpticalBiasCurrent is over the zxAnOpticalBiasCurrUpperThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.11
zxAnOptBiasCurrOverThreshClrzxAnOptBiasCurrOverThreshAlm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.12
zxAnOptVoltageUnderThreshAlmIt indicates that zxAnOpticalSupplyVoltage is below the zxAnOpticalVoltageLowerThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.13
zxAnOptVoltageUnderThreshClrzxAnOptVoltageUnderThreshAlm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.14
zxAnOptVoltageOverThreshAlmIt indicates that zxAnOpticalSupplyVoltage is over the zxAnOpticalVoltageUpperThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.15
zxAnOptVoltageOverThreshClrzxAnOptVoltageOverThreshAlm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.16
zxAnOptTempUnderThreshAlmIt indicates that zxAnOpticalTemperature is below the zxAnOpticalTempLowerThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.17
zxAnOptTempUnderThreshClrzxAnOptTempUnderThreshAlm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.18
zxAnOptTempOverThreshAlmIt indicates that zxAnOpticalTemperature is over the zxAnOpticalTempUpperThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.19
zxAnOptTempOverThreshClrzxAnOptTempOverThreshAlm clear.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.20
zxAnOpticalModuleUnpluggedAlmThe alarm occurred when optical module is not online.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.21
zxAnOpticalModuleUnpluggedClrThe alarm restore when optical module is online.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.22
zxAnOptModuleClassMismatchAlmA zxAnOptModuleClassMismatchAlm trap is sent when the agent has detected that the optical module has plugged in, but zxAnOpticalModuleConfClass is not same as zxAnOpticalModuleActualClass.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.23
zxAnOptModuleClassMismatchClrA zxAnOptModuleClassMismatchClr trap is sent when the agent has detected that the optical module has plugged in, and zxAnOpticalModuleConfClass is same as zxAnOpticalModuleActualClass.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.24
zxAnOptChanTxPwrUnderThreshAlmA zxAnOptChanTxPwrUnderThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanCurrTxPwr has been less than the zxAnOpticalTxPwrLowerThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.51
zxAnOptChanTxPwrUnderThreshClrA zxAnOptChanTxPwrUnderThreshClr trap is sent when the zxAnOptChanTxPwrUnderThreshAlm is cleared.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.52
zxAnOptChanTxPwrOverThreshAlmA zxAnOptChanTxPwrOverThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanCurrTxPwr has been exceeded the zxAnOpticalTxPwrUpperThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.53
zxAnOptChanTxPwrOverThreshClrA zxAnOptChanTxPwrOverThreshClr trap is sent when the zxAnOptChanTxPwrOverThreshAlm is cleared.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.54
zxAnOptChanBiasUnderThreshAlmA zxAnOptChanBiasUnderThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanBiasCurrent has been less than the zxAnOpticalBiasCurrLowerThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.55
zxAnOptChanBiasUnderThreshClrA zxAnOptChanBiasCurrUnderThreshClr trap is sent when the zxAnOptChanBiasUnderThreshAlm is cleared.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.56
zxAnOptChanBiasOverThreshAlmA zxAnOptChanBiasOverThreshAlm trap is sent when the agent has detected that the zxAnOpticalChanBiasCurrent has been exceeded the zxAnOpticalBiasCurrUpperThresh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.57
zxAnOptChanBiasOverThreshClrA zxAnOptChanBiasOverThreshClr trap is sent when the zxAnOptChanBiasOverThreshAlm is cleared.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.58
zxAnOptEponGponMismatchAlmA zxAnOptEponGponMismatchAlm trap is sent when the agent has detected that the GPON optical module is plugged in the EPON port or the EPON optical module is plugged in the GPON port.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.59
zxAnOptEponGponMismatchClrA zxAnOptEponGponMismatchClr trap is sent when the zxAnOptEponGponMismatchAlm is cleared.
NOTIFICATION-TYPE
.1.3.6.1.4.1.3902.1082.30.40.3.60
zxAnOpticalModuleConformance
OBJECT IDENTIFIER
.1.3.6.1.4.1.3902.1082.30.40.4
ZTE-AN-OPTICAL-MODULE-MIB - SNMP MIB Reference | MIBs Explorer