ZHONE-COM-BRIDGE-REC-MIB
BRIDGE record MIB IP Software Minneapolis, MN
Main OID:
bridgeRecord.1.3.6.1.4.1.5504.6.77
258
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
258 total| Object Name |
|---|
bridgeInterfaceTableThis table contains information required for the management
of bridge interfaces. SEQUENCE OF BridgeInterfaceEntry .1.3.6.1.4.1.5504.4.7.2 |
bridgeInterfaceEntryAn entry exists for each bridge interface in the system.
At a mininum the ifIndex must be present to create a row. BridgeInterfaceEntry .1.3.6.1.4.1.5504.4.7.2.1 |
bridgeIfVpiIf this bridge interface is on an ATM VC, the ATM VPI
is specified here. If the bridge interface is not an ATM VC,
this field is ignored. The VPI value for a VPL or VCL. The
value VPI=0 is only allowed for a VCL. For ATM UNIs supporting
VPCs the VPI value ranges from 0 to 255. The VPI
value 0 is supported for ATM UNIs conforming to
the ATM Forum UNI 4.0 Annex 8 (Virtual UNIs)
specification. For ATM UNIs supporting VCCs the
VPI value ranges from 0 to 255. For ATM NNIs the
VPI value ranges from 0 to 4095. The maximum VPI
value cannot exceed the value allowable by
atmInterfaceMaxVpiBits defined in ATM-MIB.rw AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.5504.4.7.2.1.1 |
bridgeIfVciIf this bridge interface is on an ATM VC, the ATM VCI is
specified here. The range is 32...65535. The maximum VCI
value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB.
If the bridge interface is not an ATM VC, but for example an
ethernet interface, this field should be set to 0.rw AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.5504.4.7.2.1.2 |
bridgeIfVlanIdThe Virtual LAN Id for VLAN Tag Insertion.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.3 |
bridgeIfStripAndInsertIf true, enable VLAN Tagging.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.4 |
bridgeIfCustomARPIf true, send ARP requests selectively or by flood.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.5 |
bridgeIfFilterBroadcastIf true, discard non-ARP broadcast packets.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.6 |
bridgeIfLearnIpIf true, snoop unicast packets to build ARP table.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.7 |
bridgeIfLearnUnicastIf true, snoop unicast packets to build MAC paths.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.8 |
bridgeIfMaxUnicastMaximum number of unicast addresses for I/F.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.9 |
bridgeIfLearnMulticastIf true, snoop multicast packets for IGMP joins/leaves.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.10 |
bridgeIfForwardToUnicastIf true, attempt to forward via unicast MAC paths.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.11 |
bridgeIfForwardToMulticastIf true, attempt to forward via multicast MAC paths.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.12 |
bridgeIfForwardToDefaultIf true, attempt to forward via VLAN default paths.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.13 |
bridgeLowerIfIndexAn entry exists for each bridge interface in the
system. Only Ifindex and lower if index is needed
to create a row.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.5504.4.7.2.1.14 |
bridgeIfRowStatusThis object is used to create and remove rows in the table.
See bridgeInterfaceEntry description for minimum requirements.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.2.1.15 |
bridgeIfCustomDHCPIf TRUE, forwards broadcast DHCPOFFER or DHCPACK
packets even if bridgeFilterBroadcast is TRUE for that
interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.16 |
bridgeIfIngressPacketRuleGroupIndexIndex used as partial address of a group of entries
in the packetRuleTable, each of which prescribes
a filtering condition for the ingress interface.rw PacketRuleGroupIndex .1.3.6.1.4.1.5504.4.7.2.1.17 |
bridgeIfVlanIdCOSThe Class-Of-Service (COS) value used for VLAN Tag Insertion.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.18 |
bridgeIfOutgoingCOSOptionDetermines COS setting on packets bridged out this interface.
disable - COS setting is untouched.
all - COS will be set to bridgeIfOutgoingCOSValue.rw Enumeration .1.3.6.1.4.1.5504.4.7.2.1.19 |
bridgeIfOutgoingCOSValueThe COS value loaded into outgoing tagged packets.
Applicable only if interface sends tagged packets and
bridgeIfOutgoingCOSOption is outgoingCOSOption_all.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.20 |
bridgeIfStagTPIDThe value of the tag protocol identifier that is being
used for QinQ packets. (0x8100 is default.)rw Integer32 (33024 | 34984 | 37120 | 37376) .1.3.6.1.4.1.5504.4.7.2.1.21 |
bridgeIfStagIdThe s-tag value that we are expecting to put on packets
that are Rxed on this interface.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.22 |
bridgeIfStagStripAndInsertIf true, enable S-tag tagging on this IF.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.23 |
bridgeIfStagOutgoingCOSOptionDetermines s-tag COS settings on packets bridged
out this interface:
disable - s-tag COS setting just passed as Rxed.
all - s-tag COS will be set with s_tagOutgoingCOSValue.rw Enumeration .1.3.6.1.4.1.5504.4.7.2.1.24 |
bridgeIfStagCOSThe s-tag COS to be used when doing s-tag insertion.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.25 |
bridgeIfStagOutgoingCOSValueThe s-tag COS value loaded into outgoing tagged packets.
Applicaple only if interface sends S-tagged packets and
s_tagOutgoingCOSOption is All.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.26 |
bridgeIfMcastControlListList of mcast-control-ids this bridge-interface-record
is associated with. It is an integer stored as string, and
controls which channels a user can watch. Note: unlike
for IP, an empty list here allows user to watch all
channels.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.2.1.27 |
bridgeIfMaxVideoStreamsMaximum number of multicast (video) streams that
we will support.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.2.1.28 |
bridgeIfIsPPPoAIf true, this interface accepts PPPoA packets and will
bridge them out as PPPoE packets.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.29 |
bridgeIfFloodUnknownIf true, flood frames with unknown unicast MAC
address that would otherwise be discarded.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.30 |
bridgeIfFloodMulticastIf true, flood all multicast traffic received on
this bridge to all other ports on this vlan.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.31 |
bridgeIfEgressPacketRuleGroupIndexIndex used as partial address of a group of entries
in the packetRuleTable, each of which prescribes
a filtering condition for the egress interface.rw PacketRuleGroupIndex .1.3.6.1.4.1.5504.4.7.2.1.32 |
bridgeIfTableBasedFilternone : Dynamic IP Filtering on bridge based on DHCP,
is disabled.
BIT 1(mac) : MAC address based Filtering based on DHCP, is enabled.
BIT 2(ip) : IP address based dynamic IP Filtering based on DHCP,
is enabled.
Defval is changed to correct the Zhone script errors.rw Bits .1.3.6.1.4.1.5504.4.7.2.1.33 |
bridgeIfDhcpLearnnone :IP address and Mac address are not learned from DHCP packets.
BIT 1 (mac): MAC addresses are learned from DHCP packets.
ip 2 (ip) : IP addresses are learned from DHCP packets.
The Defval is changed to correct the Zhone script errors.rw Bits .1.3.6.1.4.1.5504.4.7.2.1.34 |
bridgeIfOnDemandStatsEnabledIf true, the on-demand stats collection for this bridge
interface will be enabled and packets will be counted.
If bytes, the on-demand stats collection for this bridge
interface will be enabled and abd bytes will be counted.rw Enumeration .1.3.6.1.4.1.5504.4.7.2.1.35 |
bridgeIfMvrVlanThe Multicast Vlan Registration (MVR) vlan ID.
Multicast video packets with this vlan can be
vlan translated out this bridge.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.36 |
bridgeIfVlanXlateFromIf a packet's VLAN ID value matches this object's
value then the packet's VLAN ID will be translated
to the value of bridgeIfVlanId.
A zero value disables translation.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.37 |
bridgeIfSlanXlateFromIf a packet's SLAN ID value matches this object's
value then the packet's SLAN ID will be translated
to the value of bridgeIfStagId.
A zero value disables translation.rw Integer32 .1.3.6.1.4.1.5504.4.7.2.1.38 |
bridgeIfBridgeStateValues:
up(1), UP
down(2), DWN
trouble(3), TRB
notAvailable(4), NA
initializing(5), INI
adminDown(6), ADN
adminStateTest(7), TST
adminStateNone(8), N/S
ready(9), RDY
discovering(10), DSC
unknown(11), ???
blocked(12), BLK
pending(13), PND
disabled(14), DIS
learning(15), LRN
forwarding(16), FWD
blockedFlapping(17), BLF
blockedPersistent(18), BLP
blockedFlappingPersistenr(19), BFPrw BridgeState .1.3.6.1.4.1.5504.4.7.2.1.39 |
bridgeIfUnblockSet to TRUE to unblock a bridge that is
blocked due to flapping.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.2.1.40 |
bridgeTypebridge typerw Enumeration .1.3.6.1.4.1.5504.4.7.2.1.41 |
bridgeIfGponGemPortIdGPON GEM Port ID used only to create a bridge on a GPON ONU.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.2.1.42 |
bridgeIfGponTrafficProfileGPON Traffic Profile Index used only to create a bridge
on a GPON ONU.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.2.1.43 |
bridgeIfIncomingCOSOptionDetermines COS settings on incoming packets bridged
out this interface:
disable - COS replcement feature is disabled
all - COS will be set with vlanIDCOS.rw Enumeration .1.3.6.1.4.1.5504.4.7.2.1.44 |
bridgeIfStagIncomingCOSOptionDetermines s-tag COS settings on incoming packets bridged
out this interface:
disable - s-tag COS setting just passed as Rxed.
all - s-tag COS will be set with s-tagIdCOS.rw Enumeration .1.3.6.1.4.1.5504.4.7.2.1.45 |
staticBridgeTableA collection of staticBridgeEntries. SEQUENCE OF StaticBridgeEntry .1.3.6.1.4.1.5504.4.7.3 |
staticBridgeEntryStatic Bridge entries are created by the user in
order to specify forwarding for a particular
interface, vlanId, mac address or ip address,
slanId (for QinQ).
The INDEX value for staticBridgeEntry consists of
following 5 values:
ifIndex
staticBridgeAddressType
bridgeIfVlanId
staticBridgeMacOrIpAddress
bridgeIfStagId
If staticBridgeAddressType is set to macAddr(1), then
staticBridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeAddressType is set to ipAddr(2), then
staticBridgeMacOrIpAddress represents an IP Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeAddressType is set to vlanIdAddr(3),
then ifIndex and bridgeIfVlanId are used for the
bridge path.
If staticBridgeAddressType is set to globalAddr(4),
then ifIndex is used for the bridge path. StaticBridgeEntry .1.3.6.1.4.1.5504.4.7.3.1 |
staticBridgeMacOrIpAddressIf the staticBridgeAddressType is set to macAddr(1),
then this field represents a MAC address.
If the staticBridgeAddressType is set to ipAddr(2),
then this field represents an IP address. PhysAddress .1.3.6.1.4.1.5504.4.7.3.1.1 |
staticBridgeAddressTypeIf staticBridgeAddressType is set to macAddr(1), then
staticBridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeAddressType is set to ipAddr(2), then
staticBridgeMacOrIpAddress represents an IP Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeAddressType is set to vlanIdAddr(3) or
intralinkAddr(7), then ifIndex and bridgeIfVlanId are
used for the bridge path.
If staticBridgeAddressType is set to globalAddr(4),
globalIntralinkAddr(8), or mvrAddr(13) then ifIndex
is used for the bridge path.
If staticBridgeAddressType is set to
dhcpAllowOui( 720901) then the first 3 bytes of the
MAC address contains the OUI that we will allow DHCP
addresses to be granted to, global scope.
If staticBridgeAddressType is set to dhcpIpAddr(9), or
to dhcpMacAddr(10), then the other fields are populated
as for address types ipAddr and macAddr respectively,
with the difference that these are secure entries,
learned by snooping DHCP.
If staticBridgeAddressType is set to vlanParms(14),
then the static bridge entry holds parameters for
the given VLAN and SLAN ID (for example, flap mode,
unicast aging period, etc) and is not associated
with any specific bridge, but with all bridges
with the same VLAN/SLAN ID. For this reason,
the IfIndex of this entry must be zero.
If staticBridgeAddressType is set to secMvrAddr(15),
then the static bridge entry holds parameters for
a Secondary MVR path. The VLAN ID of this entry is
the Secondary VLAN ID. Enumeration .1.3.6.1.4.1.5504.4.7.3.1.2 |
staticBridgeMulticastAgingMulticast Aging period in tenths of seconds for the
specified VLAN. After the specified aging period is
met, the VLAN address is deleted from the routing table.
A value of 0 indicates that aging is turned off.
Maximum value is 2147483647 tenths of seconds,
which equates to approximately 2485.51 days.rw Integer32 .1.3.6.1.4.1.5504.4.7.3.1.3 |
staticBridgeRowStatusUsed to create, modify or delete an entry in this
table.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.3.1.4 |
staticBridgeFlapControlThis object enables or disable Flap Control in the Bridge
Filter Table. The value 'disable(2)' turns Flap Control mode
off. The values 'enable(3)' or 'fast(4) turn flap control mode on.
'Enable(3)' applies a hold time of 60 secs before allowing addr/IP
to be moved to a new port, while 'fast(4)' applies a hold time of
0 secs. A value of 'default(1)' indicates 'Don't Care' and defaults
to a disable or enable set by another entry.rw Enumeration .1.3.6.1.4.1.5504.4.7.3.1.5 |
staticBridgeUnicastAgingMulticast Aging period in tenths of seconds for the
specified VLAN. After the specified aging period is
met, the VLAN address is deleted from the routing table.
A value of 0 indicates that aging is turned off.
Maximum value is 2147483647 tenths of seconds,
which equates to approximately 2485.51 days.rw Integer32 (0 | 120..2147483647) .1.3.6.1.4.1.5504.4.7.3.1.6 |
staticBridgeIgmpQueryIntervalHow often (in seconds) we as a bridge inject IGMP query
values into the stream.rw Integer32 .1.3.6.1.4.1.5504.4.7.3.1.7 |
staticBridgeFlagsnone : IGMP Snooping with Proxy reporting is disabled.
BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets.
BIT 1(igmpRespondToQuery) : igmpRespondToQuery is enabled for IGMP packets.
BIT 2(igmpUseBridgeIpAddress) : igmpUseBridgeIpAddress is enabled for IGMP packets.
BIT 3(forceIGMPv2Down) : forceIGMPv2Down is enabled for subscriber side
BIT 4(forceIGMPv2Up) : forceIGMPv2Up is enabled for uplink/network siderw Bits .1.3.6.1.4.1.5504.4.7.3.1.8 |
staticBridgeIgmpCustomIpAddressAllow the configuration of the source IP address for
packets that we originate upstream when doing IGMP
Porxy on a bridge.rw IpAddress .1.3.6.1.4.1.5504.4.7.3.1.9 |
staticBridgeLoopPreventionThis field does the following options,'BlockAsym(1)' blocks a
learning bridge if flap is detected between it and an uplink bridge.
'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a
learning bridge if it flaps against another learning bridge.rw Enumeration .1.3.6.1.4.1.5504.4.7.3.1.10 |
staticBridgeIgmpDscpThis parameter indicates DSCP value for igmp traffic.
Valid code values:
<0-63> Differentiated services codepoint value
af11 Mark packets with AF11 dscp (001010)
af12 Mark packets with AF12 dscp (001100)
af13 Mark packets with AF13 dscp (001110)
af21 Mark packets with AF21 dscp (010010)
af22 Mark packets with AF22 dscp (010100)
af23 Mark packets with AF23 dscp (010110)
af31 Mark packets with AF31 dscp (011010)
af32 Mark packets with AF32 dscp (011100)
af33 Mark packets with AF33 dscp (011110)
af41 Mark packets with AF41 dscp (100010)
af42 Mark packets with AF42 dscp (100100)
af43 Mark packets with AF43 dscp (100110)
cs1 Mark packets with CS1(precedence 1) dscp (001000)
cs2 Mark packets with CS2(precedence 2) dscp (010000)
cs3 Mark packets with CS3(precedence 3) dscp (011000)
cs4 Mark packets with CS4(precedence 4) dscp (100000)
cs5 Mark packets with CS5(precedence 5) dscp (101000)
cs6 Mark packets with CS6(precedence 6) dscp (110000)
cs7 Mark packets with CS7(precedence 7) dscp (111000)
default Mark packets with default dscp (000000)
ef Mark packets with EF dscp (101110)rw OCTET STRING .1.3.6.1.4.1.5504.4.7.3.1.11 |
bridgeIfLookupTableA collection of bridgeIfLookupTable entries. SEQUENCE OF BridgeIfLookupEntry .1.3.6.1.4.1.5504.4.7.4 |
bridgeIfLookupEntryBridge IfLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.
The INDEX value for bridgeIfLookupEntry consists of
following 5 values:
bridgeIfAddressType
bridgeIfMacOrIpAddress
bridgeIfVlanId
ifIndex
bridgeIfStagId
If bridgeIfAddressType is set to unicast_mac(1),
then bridgeIfMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId/Slanid and
bridgeIfMacOrIpAddress are use for the bridge path.
If bridgeIfAddressType is set to multicast_mac(2),
then bridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId/SlanId and
bridgeIfMacOrIpAddress are used for bridge path.
If bridgeIfAddressType is set to ip_address(3),
then ifIndex and bridgeIfVlanId/SlanId are used
for the bridge path. BridgeIfLookupEntry .1.3.6.1.4.1.5504.4.7.4.1 |
bridgeIfAddressTypeIf bridgeIfAddressType is set to unicast_mac(1),
then bridgeIfMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress
are used for the bridge path.
If bridgeIfAddressType is set to multicast_mac(2),
then bridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress
are used for the bridge path.
If bridgeIfAddressType is set to ip_address(3),
then ifIndex and bridgeIfVlanId are used for the
bridge path.
If bridgeIfAddressType is set to dhcp_mac(4), or
dhcp_ip(5), then the address is as desribed for types
1 and 3, respectively, and the address was learned
by snooping DHCP packets.
ipV6Address(6) is the same as ipAddress(3) except for IPv6
address format.
dhcpV6Mac(7) is the same as dhacpMac(4) except for IPv6
address format.
dhcpV7Ip(8) is the same as dhcpIp(5) except for IPv6
address format. Enumeration .1.3.6.1.4.1.5504.4.7.4.1.1 |
bridgeIfMacOrIpAddressIf bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1)
or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4),
then bridgeIfMacOrIpAddress represents a MAC Address.
If bridgeIfAddressType is set to FILTER_ENTRY_IP_ADDRESS(3), or
to FILTER_ENTRY_DHCP_IP(5),
then bridgeIfMacOrIpAddress represents an IP Address. PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.4.1.2 |
bridgeIfLookupStaticOrDynamicIf bridgeIfLookupStaticOrDynamic is set to 1,
then this table entry is static and persistent.
If bridgeIfLookupStaticOrDynamic is set to 2,
then this table entry is learned and is not persistent.ro Enumeration .1.3.6.1.4.1.5504.4.7.4.1.3 |
bridgeIfLookupFlushThe object 'bridgeIfLookupFlush' allows a user to flush
learned entries in the bridgeFilterTable when the ifIndex
of the entry is not known. A combination of address type,
MAC or IP address and vlan ID is used to determine the
ifIndex of the entry to be removed. Setting the object
to 'true' causes the flush action to occur.
After the flush action is taken, the value of
bridgeIfLookupFlush is immediately set back to 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.4.1.4 |
bridgeAddressLookupTableA collection of bridgeAddressLookupTable entries. SEQUENCE OF BridgeAddressLookupEntry .1.3.6.1.4.1.5504.4.7.5 |
bridgeAddressLookupEntryBridgeAddressLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.
The INDEX value for bridgeIfLookupEntry consists of
following 5 values:
ifIndex
bridgeIfAddressType
bridgeIfMacOrIpAddress
bridgeIfVlanId
bridgeIfStagId BridgeAddressLookupEntry .1.3.6.1.4.1.5504.4.7.5.1 |
bridgeAddressLookupStaticOrDynamicIf bridgeAddressLookupStaticOrDynamic is set to 1,
then this table entry is static and persistent.
If bridgeAddressLookupStaticOrDynamic is set to 2,
then this table entry is learned and is not persistent.ro Enumeration .1.3.6.1.4.1.5504.4.7.5.1.1 |
bridgeAddressLookupFlushThe object 'bridgeIfAddressFlush' allows a user to flush
learned entries in the bridgeFilterTable when the ifIndex
of the entry is known. The ifIndex is used to determine
which interface is to be removed. Setting the object
to 'true' causes the flush action to occur.
After the flush action is taken, the value of
bridgeIfLookupFlush is immediately set back to 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.5.1.2 |
packetRuleGroup OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.6 |
packetRuleGroupIndexNextA scalar representing the next available Group Index for
Packet Rule Table Entries.ro PacketRuleGroupIndex .1.3.6.1.4.1.5504.4.7.6.1 |
packetRuleGroupNextIndexTableA collection of entries each representing the next
available index for that group. SEQUENCE OF PacketRuleGroupNextIndexEntry .1.3.6.1.4.1.5504.4.7.6.2 |
packetRuleGroupNextIndexEntryA packetRuleGroupNextIndexEntry contains the next
available index for that packetRuleGroup. PacketRuleGroupNextIndexEntry .1.3.6.1.4.1.5504.4.7.6.2.1 |
packetRuleGroupMemberNextIndexThe next index available in a given packetRuleGroup
for a new packetRuleEntry.ro PacketRuleGroupIndex .1.3.6.1.4.1.5504.4.7.6.2.1.1 |
packetRuleTableA collection of packetRuleEntries. SEQUENCE OF PacketRuleEntry .1.3.6.1.4.1.5504.4.7.6.3 |
packetRuleEntryPacket Rule entries are created by the user in
order to specify filtering or other packet manipulation
for a particular interface. PacketRuleEntry .1.3.6.1.4.1.5504.4.7.6.3.1 |
packetRuleGroupMemberIndexThe index of a packetRuleEntry in a given packetRuleGroup. Integer32 .1.3.6.1.4.1.5504.4.7.6.3.1.1 |
packetRuleTypeA 32-bit value which determines a filter to be applied to
packets on the interface matching the pattern specified in
packetRuleValue. The size and offset of the pattern in the
packet will depend on packetRuleType.
Bits may be set in packetRuleType determining properties
of the filtering to be applied:
BRIDGE_FORBID = 0x10
BRIDGE_INPUT = 0x20
BRIDGE_TERMINATE = 0x40
When BRIDGE_FORBID is set, packets matching the pattern are
dropped; when it is clear, matching packets are forwarded.
When BRIDGE_INPUT is set, filtering is applied to packets
received on the interface; when it is clear, filtering is
applied to packets to be transmitted on the interface.
When BRIDGE_TERMINATE is set, processing of a packet matching
the pattern ends the scan of filtering specifications; when
it is clear, processing continues.
Values of packetRuleType include
DST_MAC_SWAP_STATIC = 0x25
DST_MAC_SWAP_DYNAMIC = 0x28
BRIDGE_INSERT_OPTION82 = 0x61
BRIDGE_DHCP_RELAY = 0x62
BRIDGE_INSERT_PPPOE_VENDOR_TAG = 0x63
BRIDGE_FORBID_OUI = 0x72
RATE_LIMIT_DISCARD = 0x64
COLOR_AWARE_RATE_LIMIT_DISCARD = 0x67rw Enumeration .1.3.6.1.4.1.5504.4.7.6.3.1.2 |
packetRuleValueA variable-length field whose meaning depends on
packetRuleType.
If bridgeForbidOui, it specifies a bit pattern to be
matched in a packet, stored as a string, but specified in
the pattern 'nn:nn:nn...nn:nn', where 'nn' is a hex number
specifying a byte of the pattern. E.g. a packetRuleValue
of '00:02:02' specifies the OUI to be dropped.
If dhcpRelay, it is ascii integer which specifies dhcp
subnet group.
If bridgeInsertOption82, this value is ignored.
If bridgeInsertPPPoEVendorTag, it specifies an ASCII string
of up to 48 bytes to be inserted into PPPoE discovery packets
(PADI/PADR) which transit this node. String will be inserted
as a Vendor-Specific tag.
If rateLimitDiscard, this value represents a maximum rate (in kbps).
If aclAllow/aclDeny, a text string of the form:
all | [Keyword NamedValue | Value[/N]]*
where Keyword identifies the field of interest,
Value is context dependent on the field, NamedValue
is an alias for a Value. N indicates the number of
most significant bits of Value to test. If omitted
it defaults to the max allowed for the field.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.6.3.1.3 |
packetRuleRowStatusThis object is used to create and remove rows in the table.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.6.3.1.4 |
packetRuleValue2A variable-length field whose meaning depends on
packetRuleType.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.6.3.1.5 |
packetRuleValue3A variable-length field whose meaning depends on
packetRuleType.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.6.3.1.6 |
packetRuleValue4A variable-length field whose meaning depends on
packetRuleType.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.6.3.1.7 |
packetRuleValue5A variable-length field whose meaning depends on
packetRuleType.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.6.3.1.8 |
packetRuleGroupIndexA scalar representing the Group Index for a set of
Packet Rule Table Entries. PacketRuleGroupIndex .1.3.6.1.4.1.5504.4.7.6.3.1.9 |
packetRuleValue6A variable-length field whose meaning depends on
packetRuleType.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.6.3.1.10 |
packetRuleValue7A variable-length field whose meaning depends on
packetRuleType.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.5504.4.7.6.3.1.11 |
bridgePPPoETableFor PPPoA-to-PPPoE tables, provide a lookup by ifIndex into the
PPPoE tables. If the session has not been created for this PPPoA
ifIndex, then there will be no table data. SEQUENCE OF BridgePPPoEEntry .1.3.6.1.4.1.5504.4.7.7 |
bridgePPPoEEntryDescription. BridgePPPoEEntry .1.3.6.1.4.1.5504.4.7.7.1 |
bridgePPPoEBrasMacDestination mac address.ro OCTET STRING .1.3.6.1.4.1.5504.4.7.7.1.1 |
bridgePPPoELocalHostMacSource mac address.ro OCTET STRING .1.3.6.1.4.1.5504.4.7.7.1.2 |
bridgePPPoEEIfIndexPPPoE port's ifIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.5504.4.7.7.1.3 |
bridgePPPoESessionIDPPPoE session ID.ro Integer32 .1.3.6.1.4.1.5504.4.7.7.1.4 |
bridgePPPoESlanIdSLan ID of BRAS.ro Integer32 .1.3.6.1.4.1.5504.4.7.7.1.5 |
bridgePPPoEVlanIdVLAN ID of BRAS.ro Integer32 .1.3.6.1.4.1.5504.4.7.7.1.6 |
bridgePPPoEEncapLLCPPPoA encapsulationro Enumeration .1.3.6.1.4.1.5504.4.7.7.1.7 |
stpParam OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.8 |
stpParamNameset this field if you are using MSTP, use the name of the bridge as a key.rw ZhoneAdminString (Zhone-TC) .1.3.6.1.4.1.5504.4.7.8.1 |
stpParamRevisionThis parameter is used if you are running MSTP only. Currently
we don't support any revisions to MSTP, so revision 0 is default.rw Unsigned32 (0) .1.3.6.1.4.1.5504.4.7.8.2 |
stpParamBridgePriorityThe priority ID that will be advertised for this bridge.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.8.3 |
stpParamForceVersionThe protocol to initiate with. 3- MSTP, 2- RSTP, 0- STP.rw Unsigned32 (0 | 2 | 3) .1.3.6.1.4.1.5504.4.7.8.4 |
stpParamFwdDelayThe delay used by STP bridges to transition Root and Designated Ports to Forwarding.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.8.5 |
stpParamHelloTimeThe interval between periodic transmissions of Configuration
Messages by Designated Ports. We only support a hello time of 2 currently.rw Unsigned32 (2) .1.3.6.1.4.1.5504.4.7.8.6 |
stpParamMigrateTimeThe initial value of the mdelayWhile and edgeDelayWhile timers.
We currently only support a value of 3 for this timer.rw Unsigned32 (3) .1.3.6.1.4.1.5504.4.7.8.7 |
stpParamTxHoldCountThe transmit hold count is used by the Port Transmit state machine to limit transmission rate.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.8.8 |
stpParamMaxAgeThe maximum age of the information transmitted by the bridge when it is the Root Bridge.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.8.9 |
stpBindTableThe stpBind table is used to store the entries of stpBind
which hold the relationship between the ifIndex on which
STP is to run on, and the MSTP instance if any. SEQUENCE OF StpBindEntry .1.3.6.1.4.1.5504.4.7.9 |
stpBindEntrystpBindEntry is used to specify the type of STP
that is to run on an ifIndex. An InstanceID of 0
specifies RSTP.
An InstanceId > 0 indicates MSTP. StpBindEntry .1.3.6.1.4.1.5504.4.7.9.1 |
stpBindInstanceIDThis is a hidden storage of the InstanceId of an entry. Unsigned32 .1.3.6.1.4.1.5504.4.7.9.1.1 |
stpBindRowStatusDescription.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.9.1.2 |
stpBindPortPriorityPortPriority is used to specify the STP priority of
this port.rw Unsigned32 .1.3.6.1.4.1.5504.4.7.9.1.3 |
mstpInstanceTableDescription. SEQUENCE OF MstpInstanceEntry .1.3.6.1.4.1.5504.4.7.10 |
mstpInstanceEntryDescription. MstpInstanceEntry .1.3.6.1.4.1.5504.4.7.10.1 |
mstpInstanceRowStatusDescription.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.10.1.1 |
mstpInstanceNameA name for this mstp instance and vlanId.rw ZhoneAdminString (Zhone-TC) .1.3.6.1.4.1.5504.4.7.10.1.2 |
bridgeStatsTableThe bridgeStatsTable is used to access the statistics of the entries in the bridge table. SEQUENCE OF BridgeStatsEntry .1.3.6.1.4.1.5504.4.7.11 |
bridgeStatsEntryDisplays the bridge statistics table entries. BridgeStatsEntry .1.3.6.1.4.1.5504.4.7.11.1 |
bridgeStatsUcastRcvdUnicast packets received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.1 |
bridgeStatsMcastRcvdMulticast packets received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.2 |
bridgeStatsBcastRcvdBroadcast packets received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.3 |
bridgeStatsUcastSentUnicast packets sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.4 |
bridgeStatsMcastSentMulticast packets sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.5 |
bridgeStatsBcastSentBroadcast packets sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.6 |
bridgeStatsErrorSentError packets sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.7 |
bridgeOnDemandStatsRulesSupportedGet the number of supported Ingress Stats available for a line card.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.8 |
bridgeOnDemandStatsRulesRemainingGet the number of remaining Ingress Stats available for a line cardro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.9 |
bridgeStatsBSDUcastBlockedNumber of unicast packets dropped due to Bridge Packet Storm Detection
threshold exceeded.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.10 |
bridgeStatsBSDMcastBlockedNumber of multicast packets dropped due to Bridge Packet Storm Detection
threshold exceeded.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.11 |
bridgeStatsBSDBcastBlockedNumber of broadcast packets dropped due to Bridge Packet Storm Detection
threshold exceeded.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.12 |
bridgeStatsBSDAlarmCountThis counter reflects the number of times this interface has
transitioned to the alarm state due to the Bridge Packet Storm
Detection threshold being exceeded for a pre-defined number of
seconds.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.11.1.13 |
bridgeStatsBytesRcvdCountThis is a count of the number of bytes received.
On-demand stats must be enabled for byte counters
otherwise this counter is zero.ro Counter64 .1.3.6.1.4.1.5504.4.7.11.1.14 |
bridgeStatsBytesSentCountThis is a count of the number of bytes transmitted.
On-demand stats must be enabled for byte counters
otherwise this counter is zero.ro Counter64 .1.3.6.1.4.1.5504.4.7.11.1.15 |
bridgeStatsTicksLastClearedLinecard tick value when bridge was last cleared.ro Counter64 .1.3.6.1.4.1.5504.4.7.11.1.16 |
bridgeStatsTicksNowLinecard current tick value.ro Counter64 .1.3.6.1.4.1.5504.4.7.11.1.17 |
bridgeStatsTicksPerSecondLinecard current tick value.ro Counter64 .1.3.6.1.4.1.5504.4.7.11.1.18 |
bridgeCmd OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.12 |
bridgeCmdOperationBridge command ID value.rw Enumeration .1.3.6.1.4.1.5504.4.7.12.1 |
bridgeCmdFilterMaskBridge command filters bit mask.
If a bridge filter is enabled then the associated bridge filter
value must be included in the SNMP packet.
If the bridge filter mask is all zeros then no filters will
be applied and the bridge command will apply to all bridges
in the system.rw Bits .1.3.6.1.4.1.5504.4.7.12.2 |
bridgeCmdIfIndexBridge command 'ifIndex' filter value. If this object is
included in the SNMP packet then the associated filter must
be enabled in the bridge filter mask (bridgeCmdFilterMask).rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.5504.4.7.12.3 |
bridgeCmdVlanIdBridge command 'VLAN' filter value. If this object is
included in the SNMP packet then the associated filter must
be enabled in the bridge filter mask (bridgeCmdFilterMask).rw INTEGER .1.3.6.1.4.1.5504.4.7.12.5 |
bridgeCmdSlanIdBridge command 'SLAN' filter value. If this object is
included in the SNMP packet then the associated filter must
be enabled in the bridge filter mask (bridgeCmdFilterMask).rw INTEGER .1.3.6.1.4.1.5504.4.7.12.6 |
bridgeCmdSlotBridge command 'SLOT' filter value. If this object is
included in the SNMP packet then the associated filter must
be enabled in the bridge filter mask (bridgeCmdFilterMask).rw INTEGER .1.3.6.1.4.1.5504.4.7.12.7 |
bridgeCmdPortBridge command 'PORT' filter value. This is the ifIndex
of the linegroup on which the bridge is stacked
If this object is included in the SNMP packet then the
associated filter must be enabled in the bridge filter
mask (bridgeCmdFilterMask).rw INTEGER .1.3.6.1.4.1.5504.4.7.12.8 |
bridgeCmdIpAddressBridge command 'IP Address' filter value.
If this object is included in the SNMP packet then the
associated filter must be enabled in the bridge filter
mask (bridgeCmdFilterMask).rw IpAddress .1.3.6.1.4.1.5504.4.7.12.9 |
bridgeCmdMacAddressBridge command 'MAC Address' filter value.
If this object is included in the SNMP packet then the
associated filter must be enabled in the bridge filter
mask (bridgeCmdFilterMask).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.12.10 |
eapsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.13 |
eapsConfigTableThis table contains information required for the management
of EAPS domains. SEQUENCE OF EapsConfigEntry .1.3.6.1.4.1.5504.4.7.13.1 |
eapsConfigEntryAn entry exists for each EAPS domain in the system. EapsConfigEntry .1.3.6.1.4.1.5504.4.7.13.1.1 |
eapsConfigPrimaryPortLineGroupThis object contains the line group IfIndex of the Primary EAPS Port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.5504.4.7.13.1.1.1 |
eapsConfigSecondaryPortLineGroupThis object contains the line group IfIndex of the Secondary EAPS Port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.5504.4.7.13.1.1.2 |
eapsConfigControlVlanThis object contains the VLAN ID of the control VLAN for this domain
record. This is the VLAN ID used in EAPS control messages.ro Integer32 .1.3.6.1.4.1.5504.4.7.13.1.1.3 |
eapsConfigIsMasterNodeIf this value is True, then this record describes a Master Node.
Otherwise, it describes a Transit Node.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.13.1.1.4 |
eapsConfigControlVlanPriorityThis object contains the Priority of the Control Vlan.rw Integer32 .1.3.6.1.4.1.5504.4.7.13.1.1.5 |
eapsConfigDomainNameThis object contains the user assigned ASCII representation of
the Domain Name for this record. This name must be unique device
wide.rw ZhoneAdminString (Zhone-TC) .1.3.6.1.4.1.5504.4.7.13.1.1.6 |
eapsConfigMsgTxIntervalThis object contains the interval, in seconds, that a node sends
Health Messages on the ring.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.5504.4.7.13.1.1.7 |
eapsConfigTimeoutOn a Master Node, this object contains the timeout, in seconds, which
the Master Node will report a Ring Fault if it does not receive a
Health Message on the ring. On a Transit Node, this is the pre-forwarding
delay timeout (also in seconds).rw Integer32 UNITS "seconds" .1.3.6.1.4.1.5504.4.7.13.1.1.8 |
eapsConfigMaxDroppedMessagesOn a Master Node, this object contains the number of contigious Health
messages that may be dropped before the node declared a Ring Fault.
This object is not used for a Transit node.rw Integer32 .1.3.6.1.4.1.5504.4.7.13.1.1.9 |
eapsConfigSnmpTrapIf this object is set to True, then this node will send SNMP Traps on
Ring State transition.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.13.1.1.10 |
eapsConfigDomainEnableIf this value is TRUE, the EAPS state machine will transition through
the initialization process to the Health state. It will begin
passing Control Messages and allow Protected VLAN data through the
EAPS Domain.
If this value is FALSE, the EAPS state machine will transition
through the reset process to the Inactivate state. It will stop
passing Control Messages and prohibit Protected VLAN data from being
passed through the EAPS Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.13.1.1.11 |
eapsConfigRowStatusThis object is used to create and remove rows in the table.
See eapsConfigEntry description for minimum requirements.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.13.1.1.12 |
eapsProtectedVlanTableThis table contains information required for the management
of a list of protected VLAN's in an EAPS domains. SEQUENCE OF EapsProtectedVlanEntry .1.3.6.1.4.1.5504.4.7.13.2 |
eapsProtectedVlanEntryAn entry for each VLAN ranges that is to be protected
in the EAPS domain. EapsProtectedVlanEntry .1.3.6.1.4.1.5504.4.7.13.2.1 |
eapsProtectedVlanEntryIndexThis object is an index which indicates which entry
in the Protected Vlan Table is being addressed. For
example, a value of 5 would indicate that the 5th entry
(row) of this table is being addressed. This entry,
along with eapsConfigPrimaryLineGroup,
eapsConfigSecondaryLineGroup, and
eapsConfigControlVlan indices select which
Protected Vlan Table entry for a given
eaps-domain-record profile. The first three
indices select the profile, this last index selects
the N'th entry in that profilero Integer32 .1.3.6.1.4.1.5504.4.7.13.2.1.1 |
eapsProtectedVlanLowerRangeThe eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects
work in conjunction with one another to set the range of the protected
vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end
of list. If eapsProtectedVlanLowerRange is not 0, but
eapsProtectedVlanUpperRange is 0, then this would be have the same
effect as both object having the same value and protect a single
vlan ID. If they are both different and non-zero, then it specifies
an inclusive range. Note that eapsProtectedVlanLowerRange must be
numerically lower than eapsProtectedVlanUpperRange.rw Integer32 .1.3.6.1.4.1.5504.4.7.13.2.1.2 |
eapsProtectedVlanUpperRangeThe eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects
work in conjunction with one another to set the range of the protected
vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end
of list. If eapsProtectedVlanLowerRange is not 0, but
eapsProtectedVlanUpperRange is 0, then this would be have the same
effect as both object having the same value and protect a single
vlan ID. If they are both different and non-zero, then it specifies
an inclusive range. Note that eapsProtectedVlanLowerRange must be
numerically lower than eapsProtectedVlanUpperRange.rw Integer32 .1.3.6.1.4.1.5504.4.7.13.2.1.3 |
eapsProtectedVlanRowStatusThis object is used to create and remove rows in the table.
See eapsProtectedVlanEntry description for minimum requirements.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.13.2.1.4 |
eapsProtectedVlanDomainNameThe domain name for the EAPS protected vlan entry.ro ZhoneAdminString (Zhone-TC) .1.3.6.1.4.1.5504.4.7.13.2.1.5 |
eapsStatusTableThis table contains status of each EAPS domain state machine. SEQUENCE OF EapsStatusEntry .1.3.6.1.4.1.5504.4.7.13.3 |
eapsStatusEntryThe entry contains status of the domain's state machine. EapsStatusEntry .1.3.6.1.4.1.5504.4.7.13.3.1 |
eapsPrevStatePrevious state for the domain.ro EapsState .1.3.6.1.4.1.5504.4.7.13.3.1.1 |
eapsStateCurrent state for the domain.ro EapsState .1.3.6.1.4.1.5504.4.7.13.3.1.2 |
eapsStatsTableEAPS statistics table. SEQUENCE OF EapsStatsEntry .1.3.6.1.4.1.5504.4.7.13.4 |
eapsStatsEntryDisplays the EAPS statistic table entries. EapsStatsEntry .1.3.6.1.4.1.5504.4.7.13.4.1 |
eapsStatsTotCtrlMsgSentTotal EAPS control messages sent.rw Integer32 .1.3.6.1.4.1.5504.4.7.13.4.1.1 |
eapsStatsTotCtrlMsgRecvdTotal EAPS control messages received.rw Integer32 .1.3.6.1.4.1.5504.4.7.13.4.1.2 |
eapsTrapPrefixPlace-holder object for EAPS traps, which must have a
final digit of 0 in OID. OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.13.5 |
eapsTrapsTraps raised by EAPS state machine. OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.13.5.0 |
eapsStateChangeState changed in the node for the EAPS domain. NOTIFICATION-TYPE .1.3.6.1.4.1.5504.4.7.13.5.0.1 |
eapsFailTimerExpFlagSetThe eapsFailTimerExpFlagSet notification is
generated when the EAPS domain's fail timer expires
for the first time, while its state is not in Fail state. NOTIFICATION-TYPE .1.3.6.1.4.1.5504.4.7.13.5.0.2 |
eapsFailTimerExpFlagClearDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.5504.4.7.13.5.0.3 |
eapsLinkDownRingCompleteIf a transit is in Link-Down state, and it receives a
Health-Check-Pdu from the Master indicating the ring is
Complete, it means there is some problem with the Transit
switch that has issued this trap message. NOTIFICATION-TYPE .1.3.6.1.4.1.5504.4.7.13.5.0.4 |
eapsTopologyTableEAPS topology table. SEQUENCE OF EapsTopologyEntry .1.3.6.1.4.1.5504.4.7.13.6 |
eapsTopologyEntryDisplays the EAPS topology table entries. EapsTopologyEntry .1.3.6.1.4.1.5504.4.7.13.6.1 |
eapsTopologyRingThis represents the link as primary or secondary. Enumeration .1.3.6.1.4.1.5504.4.7.13.6.1.1 |
eapsTopologyRowNumberThis represents the node number in the ring. Integer32 .1.3.6.1.4.1.5504.4.7.13.6.1.2 |
eapsTopologyDomainNameThis represents the domain name for this record.ro ZhoneAdminString (Zhone-TC) .1.3.6.1.4.1.5504.4.7.13.6.1.3 |
eapsTopologyMacAddrmacAddress of the element in the ring.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.13.6.1.4 |
eapsTopologyIpAddrIp addressed of the element in the ring.ro IpAddress .1.3.6.1.4.1.5504.4.7.13.6.1.5 |
eapsTopologyTypeThis represents whether the node is master or transit.ro Enumeration .1.3.6.1.4.1.5504.4.7.13.6.1.6 |
eapsTopologyPrimaryLinkNameThis represents the primary link name.ro ZhoneAdminString (Zhone-TC) .1.3.6.1.4.1.5504.4.7.13.6.1.7 |
eapsTopologyPrimaryLinkStateThis represents the primary link state.ro EapsState .1.3.6.1.4.1.5504.4.7.13.6.1.8 |
eapsTopologySecondaryLinkNameThis represents the secondary link name.ro ZhoneAdminString (Zhone-TC) .1.3.6.1.4.1.5504.4.7.13.6.1.9 |
eapsTopologySecondaryLinkStateThis represents the secondary link state.ro EapsState .1.3.6.1.4.1.5504.4.7.13.6.1.10 |
bridgeIgmpStatsTableThe bridgeIgmpStatsTable is used to access the IGMP statistics for bridges. SEQUENCE OF BridgeIgmpStatsEntry .1.3.6.1.4.1.5504.4.7.14 |
bridgeIgmpStatsEntryThe bridgeIgmpStatsEntry holds IGMP stats for a bridge interface. BridgeIgmpStatsEntry .1.3.6.1.4.1.5504.4.7.14.1 |
genQueryRxgeneral IGMP queries received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.1 |
genQueryTxgeneral IGMP queries transmitted.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.2 |
specQueryRxSpecific IGMP queries received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.3 |
specQueryTxSpecific IGMP queries transmitted.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.4 |
v2ReportsRxVersion 2 reports received (JOINs).ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.5 |
v2ReportsTxVersion 2 reports sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.6 |
leavesRxIGMP leaves received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.7 |
leavesTxIGMP leaves transmitted.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.8 |
unknownRxUnknown IGMP packets received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.9 |
errorRxIGMP packet is bad received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.10 |
actChansNumber of active muticast channels.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.11 |
actHostsNumber of active multicast hosts.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.12 |
v3GenQueryRxNumber of IGMP V3 Queries received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.13 |
v3GenQueryTxNumber of IGMP V3 queries sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.14 |
v3SpecQueryRxNumber of IGMP V3 specific queries received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.15 |
v3SpecQueryTxNumber of IGMP V3 specific queries sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.16 |
v3ReportsRxNumber of IGMP V3 reports received.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.17 |
v3ReportsTxNumber of IGMP V3 reports sent.ro Unsigned32 .1.3.6.1.4.1.5504.4.7.14.1.18 |
bridgeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.15 |
bridgeTrapPrefixTraps raised for bridge conditions. OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.15.1 |
bridgeTrapsBridge traps go under here - extra layer
needed to ensure '0' in OID. OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.15.1.0 |
bridgeLoopDetectionTrap when bridge is looping on flap. NOTIFICATION-TYPE .1.3.6.1.4.1.5504.4.7.15.1.0.1 |
bridgeStormDetectionTrap sent when a bridge packet storm is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.5504.4.7.15.1.0.2 |
bridgeTrapObjects OBJECT IDENTIFIER .1.3.6.1.4.1.5504.4.7.16 |
bridgeMacAddrStringvlan/slan/macAddress for bridgero OCTET STRING .1.3.6.1.4.1.5504.4.7.16.1 |
bridgeIgmpTableThe bridgeIgmpTable is used to access the IGMP data for bridges for when
IGMP is in proxy mode and the IGMP status must be obtained from the
linecard. SEQUENCE OF BridgeIgmpEntry .1.3.6.1.4.1.5504.4.7.17 |
bridgeIgmpEntryBridgeIgmpEntry contains the igmp multicast data information for a bridge,
indexed by ifIndex, hostMac, and mcastMac. BridgeIgmpEntry .1.3.6.1.4.1.5504.4.7.17.1 |
slanIdIGMP slan identifier. Maximum value 4090 as defined by MAX_VLAN_NUM.ro Integer32 .1.3.6.1.4.1.5504.4.7.17.1.1 |
vlanIdIGMP vlan identifier. Maximum value 4090 as defined my MAX_VLAN_NUMro Integer32 .1.3.6.1.4.1.5504.4.7.17.1.2 |
mcastMacIGMP Multicast MAC addressed to bridge port.ro OCTET STRING .1.3.6.1.4.1.5504.4.7.17.1.3 |
mcastIPIGMP Multicast IP addressed to bridge port.ro IpAddress .1.3.6.1.4.1.5504.4.7.17.1.4 |
hostMacMAC address of end device receiving multicast packets.ro OCTET STRING .1.3.6.1.4.1.5504.4.7.17.1.5 |
lastJoinTimerCount down timer before IGMP entry ages out.ro Integer32 .1.3.6.1.4.1.5504.4.7.17.1.6 |
staticBridgePathTableA collection of staticBridgePathEntries.
The StaticBridgePath OID has the following format:
OID psn MAC entries IPv4 entries IPv6 entries
tlist[0] ifIndex ifIndex ifIndex
tlist[1] address type address type address type
tlist[2] vlan vlan vlan
tlist[3] macAddr[0] IPv4[0] IPv6[0]
tlist[4] macAddr[1] IPv4[1] IPv6[1]
tlist[5] macAddr[2] IPv4[2] IPv6[2]
tlist[6] macAddr[3] IPv4[3] IPv6[3]
tlist[7] macAddr[4] zero IPv6[4]
tlist[8] macAddr[5] zero IPv6[5]
tlist[9] zero zero IPv6[6]
tlist[10] zero zero IPv6[7]
tlist[11] zero zero IPv6[8]
tlist[12] zero zero IPv6[9]
tlist[13] zero zero IPv6[10]
tlist[14] zero zero IPv6[11]
tlist[15] zero zero IPv6[12]
tlist[16] zero zero IPv6[13]
tlist[17] zero zero IPv6[14]
tlist[18] zero zero IPv6[15]
tlist[19] slan slan slan SEQUENCE OF StaticBridgePathEntry .1.3.6.1.4.1.5504.4.7.18 |
staticBridgePathEntryStatic Path Bridge entries are created by the user in
order to specify forwarding for a particular
interface, vlanId, mac address or ip address,
slanId (for QinQ).
The INDEX value for staticBridgePathEntry consists of
following 5 values:
ifIndex
staticBridgePathAddressType
bridgeIfVlanId
staticBridgePathMacOrIpAddress
bridgeIfStagId
If staticBridgeAddressType is set to macAddr(1), then
staticBridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeAddressType is set to ipAddr(2), then
staticBridgeMacOrIpAddress represents an IP Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeAddressType is set to vlanIdAddr(3),
then ifIndex and bridgeIfVlanId are used for the
bridge path.
If staticBridgeAddressType is set to globalAddr(4),
then ifIndex is used for the bridge path. StaticBridgePathEntry .1.3.6.1.4.1.5504.4.7.18.1 |
staticBridgePathMacOrIpAddressIf the staticBridgeAddressType is set to macAddr(1),
then this field represents a MAC address.
If the staticBridgeAddressType is set to ipAddr(2),
then this field represents an IP address. The IP
address can be four octets ( for IPv4 ) or sixteen
octets ( for IPv6 ). NetworkAddress .1.3.6.1.4.1.5504.4.7.18.1.1 |
staticBridgePathAddressTypeIf staticBridgeIPv6AddressType is set to macAddr(1), then
staticBridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeIPv6AddressType is set to ipAddr(2), then
staticBridgeMacOrIpAddress represents an IP Address,
and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress
are used for the bridge path.
If staticBridgeIPv6AddressType is set to vlanIdAddr(3) or
intralinkAddr(7), then ifIndex and bridgeIfVlanId are
used for the bridge path.
If staticBridgeIPv6AddressType is set to globalAddr(4),
globalIntralinkAddr(8), or mvrAddr(13) then ifIndex
is used for the bridge path.
If staticBridgeIPv6AddressType is set to
dhcpAllowOui( 720901) then the first 3 bytes of the
MAC address contains the OUI that we will allow DHCP
addresses to be granted to, global scope.
If staticBridgeIPv6AddressType is set to dhcpIpAddr(9), or
to dhcpMacAddr(10), then the other fields are populated
as for address types ipAddr and macAddr respectively,
with the difference that these are secure entries,
learned by snooping DHCP.
If staticBridgeIPv6AddressType is set to vlanParms(14),
then the static bridge entry holds parameters for
the given VLAN and SLAN ID (for example, flap mode,
unicast aging period, etc) and is not associated
with any specific bridge, but with all bridges
with the same VLAN/SLAN ID. For this reason,
the IfIndex of this entry must be zero.
If staticBridgeIPv6AddressType is set to secMvrAddr(15),
then the static bridge entry holds parameters for
a Secondary MVR path. The VLAN ID of this entry is
the Secondary VLAN ID.
If staticBridgeIPv6AddressType is set to ipAddrV6(16), then
staticBridgeMacOrIpAddress represents an IPv6 Address,
and ifIndex, bridgeIfVlanId and staticBridgeIPv6MacOrIpAddress
are used for the bridge path.
If staticBridgeIPv6AddressType is set to dhcpIpAddrV6(17), or
to dhcpMacAddr(10), then the other fields are populated
as for address types ipAddr and macAddr respectively,
with the difference that these are secure entries,
learned by snooping DHCP. Enumeration .1.3.6.1.4.1.5504.4.7.18.1.2 |
staticBridgePathMulticastAgingMulticast Aging period in tenths of seconds for the
specified VLAN. After the specified aging period is
met, the VLAN address is deleted from the routing table.
A value of 0 indicates that aging is turned off.
Maximum value is 2147483647 tenths of seconds,
which equates to approximately 2485.51 days.rw Integer32 .1.3.6.1.4.1.5504.4.7.18.1.3 |
staticBridgePathRowStatusUsed to create, modify or delete an entry in this
table.rw ZhoneRowStatus (Zhone-TC) .1.3.6.1.4.1.5504.4.7.18.1.4 |
staticBridgePathFlapControlThis object enables or disable Flap Control in the Bridge
Filter Table. The value 'disable(2)' turns Flap Control mode
off. The values 'enable(3)' or 'fast(4) turn flap control mode on.
'Enable(3)' applies a hold time of 60 secs before allowing addr/IP
to be moved to a new port, while 'fast(4)' applies a hold time of
0 secs. A value of 'default(1)' indicates 'Don't Care' and defaults
to a disable or enable set by another entry.rw Enumeration .1.3.6.1.4.1.5504.4.7.18.1.5 |
staticBridgePathUnicastAgingMulticast Aging period in tenths of seconds for the
specified VLAN. After the specified aging period is
met, the VLAN address is deleted from the routing table.
A value of 0 indicates that aging is turned off.
Maximum value is 2147483647 tenths of seconds,
which equates to approximately 2485.51 days.rw Integer32 (0 | 120..2147483647) .1.3.6.1.4.1.5504.4.7.18.1.6 |
staticBridgePathIgmpQueryIntervalHow often (in seconds) we as a bridge inject IGMP query
values into the stream.rw Integer32 .1.3.6.1.4.1.5504.4.7.18.1.7 |
staticBridgePathFlagsnone : IGMP Snooping with Proxy reporting is disabled.
BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets.
BIT 1(igmpRespondToQuery) : igmpRespondToQuery is enabled for IGMP packets.
BIT 2(igmpUseBridgeIpAddress) : igmpUseBridgeIpAddress is enabled for IGMP packets.rw Bits .1.3.6.1.4.1.5504.4.7.18.1.8 |
staticBridgePathIgmpCustomIpAddressAllow the configuration of the source IP address for
packets that we originate upstream when doing IGMP
Porxy on a bridge.rw IpAddress .1.3.6.1.4.1.5504.4.7.18.1.9 |
staticBridgePathLoopPreventionThis field does the following options,'BlockAsym(1)' blocks a
learning bridge if flap is detected between it and an uplink bridge.
'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a
learning bridge if it flaps against another learning bridge.rw Enumeration .1.3.6.1.4.1.5504.4.7.18.1.10 |
staticBridgePathIgmpDscpThis parameter indicates DSCP value for igmp traffic.
Valid code values:
<0-63> Differentiated services codepoint value
af11 Mark packets with AF11 dscp (001010)
af12 Mark packets with AF12 dscp (001100)
af13 Mark packets with AF13 dscp (001110)
af21 Mark packets with AF21 dscp (010010)
af22 Mark packets with AF22 dscp (010100)
af23 Mark packets with AF23 dscp (010110)
af31 Mark packets with AF31 dscp (011010)
af32 Mark packets with AF32 dscp (011100)
af33 Mark packets with AF33 dscp (011110)
af41 Mark packets with AF41 dscp (100010)
af42 Mark packets with AF42 dscp (100100)
af43 Mark packets with AF43 dscp (100110)
cs1 Mark packets with CS1(precedence 1) dscp (001000)
cs2 Mark packets with CS2(precedence 2) dscp (010000)
cs3 Mark packets with CS3(precedence 3) dscp (011000)
cs4 Mark packets with CS4(precedence 4) dscp (100000)
cs5 Mark packets with CS5(precedence 5) dscp (101000)
cs6 Mark packets with CS6(precedence 6) dscp (110000)
cs7 Mark packets with CS7(precedence 7) dscp (111000)
default Mark packets with default dscp (000000)
ef Mark packets with EF dscp (101110)rw OCTET STRING .1.3.6.1.4.1.5504.4.7.18.1.11 |
bridgePathIfLookupTableA collection of bridgePathIfLookupTable entries.
The bridgePathIfLookup OID has the following format:
OID psn MAC entries IPv4 entries IPv6 entries
tlist[0] address type address type address type
tlist[1] macAddr[0] IPv4[0] IPv6[0]
tlist[2] macAddr[1] IPv4[1] IPv6[1]
tlist[3] macAddr[2] IPv4[2] IPv6[2]
tlist[4] macAddr[3] IPv4[3] IPv6[3]
tlist[5] macAddr[4] zero IPv6[4]
tlist[6] macAddr[5] zero IPv6[5]
tlist[7] zero zero IPv6[6]
tlist[8] zero zero IPv6[7]
tlist[9] zero zero IPv6[8]
tlist[10] zero zero IPv6[9]
tlist[11] zero zero IPv6[10]
tlist[12] zero zero IPv6[11]
tlist[13] zero zero IPv6[12]
tlist[14] zero zero IPv6[13]
tlist[15] zero zero IPv6[14]
tlist[16] zero zero IPv6[15]
tlist[17] vlan vlan vlan
tlist[18] ifIndex ifIndex ifIndex
tlist[19] slan slan slan SEQUENCE OF BridgePathIfLookupEntry .1.3.6.1.4.1.5504.4.7.19 |
bridgePathIfLookupEntryBridge IfLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.
The INDEX value for bridgeIfLookupEntry consists of
following 5 values:
bridgeIfAddressType
bridgeIfMacOrIpAddress
bridgeIfVlanId
ifIndex
bridgeIfStagId
If bridgeIfAddressType is set to unicast_mac(1),
then bridgeIfMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId/Slanid and
bridgeIfMacOrIpAddress are use for the bridge path.
If bridgeIfAddressType is set to multicast_mac(2),
then bridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId/SlanId and
bridgeIfMacOrIpAddress are used for bridge path.
If bridgeIfAddressType is set to ip_address(3),
then ifIndex and bridgeIfVlanId/SlanId are used
for the bridge path. BridgePathIfLookupEntry .1.3.6.1.4.1.5504.4.7.19.1 |
bridgePathIfAddressTypeIf bridgeIfAddressType is set to unicast_mac(1),
then bridgeIfMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress
are used for the bridge path.
If bridgeIfAddressType is set to multicast_mac(2),
then bridgeMacOrIpAddress represents a MAC Address,
and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress
are used for the bridge path.
If bridgeIfAddressType is set to ip_address(3),
then ifIndex and bridgeIfVlanId are used for the
bridge path.
If bridgeIfAddressType is set to dhcp_mac(4), or
dhcp_ip(5), then the address is as desribed for types
1 and 3, respectively, and the address was learned
by snooping DHCP packets. Enumeration .1.3.6.1.4.1.5504.4.7.19.1.1 |
bridgePathIfMacOrIpAddressIf bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1)
or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4),
then bridgeIfMacOrIpAddress represents a MAC Address.
If bridgeIfAddressType is set to FILTER_ENTRY_IP_ADDRESS(3), or
to FILTER_ENTRY_DHCP_IP(5),
then bridgeIfMacOrIpAddress represents an IP Address. NetworkAddress .1.3.6.1.4.1.5504.4.7.19.1.2 |
bridgePathIfLookupStaticOrDynamicIf bridgeIfLookupStaticOrDynamic is set to 1,
then this table entry is static and persistent.
If bridgeIfLookupStaticOrDynamic is set to 2,
then this table entry is learned and is not persistent.ro Enumeration .1.3.6.1.4.1.5504.4.7.19.1.3 |
bridgePathIfLookupFlushThe object 'bridgeIfLookupFlush' allows a user to flush
learned entries in the bridgeFilterTable when the ifIndex
of the entry is not known. A combination of address type,
MAC or IP address and vlan ID is used to determine the
ifIndex of the entry to be removed. Setting the object
to 'true' causes the flush action to occur.
After the flush action is taken, the value of
bridgeIfLookupFlush is immediately set back to 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.19.1.4 |
bridgePathAddressLookupTableA collection of bridgePathAddressLookupTable entries.
The bridgePathAddressLookup OID has the following format:
OID psn MAC entries IPv4 entries IPv6 entries
tlist[0] ifIndex ifIndex ifIndex
tlist[1] address type address type address type
tlist[2] macAddr[0] IPv4[0] IPv6[0]
tlist[3] macAddr[1] IPv4[1] IPv6[1]
tlist[4] macAddr[2] IPv4[2] IPv6[2]
tlist[5] macAddr[3] IPv4[3] IPv6[3]
tlist[6] macAddr[4] zero IPv6[4]
tlist[7] macAddr[5] zero IPv6[5]
tlist[8] zero zero IPv6[6]
tlist[9] zero zero IPv6[7]
tlist[10] zero zero IPv6[8]
tlist[11] zero zero IPv6[9]
tlist[12] zero zero IPv6[10]
tlist[13] zero zero IPv6[11]
tlist[14] zero zero IPv6[12]
tlist[15] zero zero IPv6[13]
tlist[16] zero zero IPv6[14]
tlist[17] zero zero IPv6[15]
tlist[18] vlan vlan vlan
tlist[19] slan slan slan SEQUENCE OF BridgePathAddressLookupEntry .1.3.6.1.4.1.5504.4.7.20 |
bridgePathAddressLookupEntryBridgePathAddressLookup entries are created by the user
or learned by the software in
order to specify forwarding for a particular
interface, vlanId/slanId, mac address or ip address.
The INDEX value for bridgePathLookupEntry consists of
following 5 values:
ifIndex
bridgeIfAddressType
bridgeIfMacOrIpAddress
bridgeIfVlanId
bridgeIfStagId BridgePathAddressLookupEntry .1.3.6.1.4.1.5504.4.7.20.1 |
bridgePathAddressLookupStaticOrDynamicIf bridgePathAddressLookupStaticOrDynamic is set to 1,
then this table entry is static and persistent.
If bridgePathAddressLookupStaticOrDynamic is set to 2,
then this table entry is learned and is not persistent.ro Enumeration .1.3.6.1.4.1.5504.4.7.20.1.1 |
bridgePathAddressLookupFlushThe object 'bridgePathAddressFlush' allows a user to flush
learned entries in the bridgeFilterTable when the ifIndex
of the entry is known. The ifIndex is used to determine
which interface is to be removed. Setting the object
to 'true' causes the flush action to occur.
After the flush action is taken, the value of
bridgePathLookupFlush is immediately set back to 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5504.4.7.20.1.2 |
bridgeStatusTableThis table contains runtime status for each bridge interface. SEQUENCE OF BridgeStatusEntry .1.3.6.1.4.1.5504.4.7.21 |
bridgeStatusEntryRuntime status data for a single bridge. BridgeStatusEntry .1.3.6.1.4.1.5504.4.7.21.1 |
bridgeStatusStateValues:
up(1), UP
down(2), DWN
trouble(3), TRB
notAvailable(4), NA
initializing(5), INI
adminDown(6), ADN
adminStateTest(7), TST
adminStateNone(8), N/S
ready(9), RDY
discovering(10), DSC
unknown(11), ???
blocked(12), BLK
pending(13), PND
disabled(14), DIS
learning(15), LRN
forwarding(16), FWD
blockedFlapping(17), BLF
blockedPersistent(18), BLP
blockedFlappingPersistenr(19), BFPro BridgeState .1.3.6.1.4.1.5504.4.7.21.1.1 |
bridgeRecordBRIDGE record MIB
IP Software
Minneapolis, MN MODULE-IDENTITY .1.3.6.1.4.1.5504.6.77 |
zhoneCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.5504.9 |
zhoneGroups OBJECT IDENTIFIER .1.3.6.1.4.1.5504.9.1 |