XYLAN-WSM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for XYLAN-WSM-MIB.
26
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
26 total| Object Name |
|---|
wsmPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.800.2.7.1 |
IMPORTS Unknown .1.3.6.1.4.1.800.2.7.1 |
wsmPortTableA table of port layer status and parameter information
for the WSM's physical interfaces. SEQUENCE OF WsmPortEntry .1.3.6.1.4.1.800.2.7.1.1 |
wsmPortEntryAn entry in the table, containing information about
the physical layer of a WSM interface. WsmPortEntry .1.3.6.1.4.1.800.2.7.1.1.1 |
wsmPortSlotIndexA unique value which identifies this HSM board slot.ro INTEGER .1.3.6.1.4.1.800.2.7.1.1.1.1 |
wsmPortPortIndexA unique value which identifies this WSM submodule port.ro INTEGER .1.3.6.1.4.1.800.2.7.1.1.1.2 |
wsmPortInterfaceTypeThe type of interface on this WSM physical port.ro Enumeration .1.3.6.1.4.1.800.2.7.1.1.1.3 |
wsmPortCableTypeThe type of cable attached to the universal serial
port. Non Universal Serial Ports will always return
'unknown'.
NOTE: RS-449 cables will return as RS-530 as
they are detected as the same type. RS-449 is
implemented only as a different connector (DB-37 instead
of DB-25) on the end of the cable.ro Enumeration .1.3.6.1.4.1.800.2.7.1.1.1.4 |
wsmPortSerialRxClockPolThe receive clock polarity. It is inverted or not inverted.
For interfaces that do not support this, the value
will be stored but ignored.rw Enumeration .1.3.6.1.4.1.800.2.7.1.1.1.5 |
wsmPortSerialTxClockPolThe Transmit clock polarity. It is inverted or not inverted.
For interfaces that do not support this, the value
will be stored but ignored.rw Enumeration .1.3.6.1.4.1.800.2.7.1.1.1.6 |
wsmPortFunctionTypeThe functional capability of the port.
This allows the Manager code to determine the
capabilities of the port so the proper
data can be managed based on the functions
the WAN port can provide.
A 'frameType' port supports layer 2 protocols such
as HDLC and Frame Relay.
A 'cellType' performs ATM interface functions such
as ATM T1 UNI interface.
A 'cbrType' port is used to perform Bit to Cell Conversion
(AAL1).ro Enumeration .1.3.6.1.4.1.800.2.7.1.1.1.7 |
wsmPortProtocolThe layer 2 protocol of the port.
This parameter only applies when wsmPortFunctionType
is equal to frameType(1).
For ports that don't support this (e.g. Circuit Emulation T1
ports) only a value of none(1) is supported.
For ports that support upper layer protocols (frameType ports)
a value other than none must be used.rw Enumeration .1.3.6.1.4.1.800.2.7.1.1.1.8 |
wsmPortIfIndexThe ifIndex of the WAN port.
This parameter is used in order to get the physical
port Index used for SNMP standard MIBs that
use ifIndex instead of slot/port.ro INTEGER .1.3.6.1.4.1.800.2.7.1.1.1.9 |
wsmPortT1E1StartingTimeSlotStarting TimeSlot for Fractional T1E1 board.
This is only use for Fractional T1E1 board type.
Valid Range: T1: 1..24
E1: 1..31 (May need to skip 16)
The valid range may be effected by
wsmPortT1E1NumberOfTimeSlot too.rw INTEGER .1.3.6.1.4.1.800.2.7.1.1.1.10 |
wsmPortT1E1NumberOfTimeSlotNumber of TimeSlot for Fractional T1E1 board.
This is only use for Fractional T1E1 board type.
Valid Range: T1: 1..24
E1: 1..31
The valid range may be effected by
wsmPortT1E1NumberOfTimeSlot too.rw INTEGER .1.3.6.1.4.1.800.2.7.1.1.1.11 |
wsmLinkGroup OBJECT IDENTIFIER .1.3.6.1.4.1.800.2.7.2 |
linkxTableA table of WAN link(s) configuration information. SEQUENCE OF LinkxEntry .1.3.6.1.4.1.800.2.7.2.1 |
linkxEntryAn entry in the WAN link Configuration table,
containing information about a single link's
configuration. LinkxEntry .1.3.6.1.4.1.800.2.7.2.1.1 |
linkxPeerIDThe peer ID. This is used as a unique
ID to identify a remote entity and to associate
links to it. For example, for 'normal' PPP, there
is one entry in the link table. For Multilink
PPP there are one or more multiple links.
In either case the Link table is indexed
by Link index (one per link) and by Peer ID.
When one or more entrys in the link table
has the same Peer ID, then these entries
form a group for use either for Multilink
PPP, or as a rotary group.ro INTEGER .1.3.6.1.4.1.800.2.7.2.1.1.1 |
linkxIfIndexThe ifIndex of the Link. This is used as a unique
ID to identify an individual WAN link entity.ro INTEGER .1.3.6.1.4.1.800.2.7.2.1.1.2 |
linkxDescriptionA description for this WAN link.rw DisplayString .1.3.6.1.4.1.800.2.7.2.1.1.3 |
linkxAdminStatusThis object controls the Administrative Status
of this WAN Link Entity. Enabled will allow the
Link Entity to operate. Disabled will
disable the Link Entity without deleting it.
Delete will disable the Link entity and delete
the PPP configuration record.rw Enumeration .1.3.6.1.4.1.800.2.7.2.1.1.4 |
linkxTypeThe type of link. A wsmPort type is for
WSM serial and Fractional T1 ports. An
ISDN call is for incoming or outgoing
ISDN calls. Additional information
can then be found in Xylan and Standard
MIBs based on the type of the link.rw Enumeration .1.3.6.1.4.1.800.2.7.2.1.1.5 |
linkxSlotThe slot that is Link is on or zero if the
link is not tied to a given slot (e.g.
for ISDN incoming calls).
If type is wsmPort(1), this must be a non-zero
value.rw INTEGER .1.3.6.1.4.1.800.2.7.2.1.1.6 |
linkxPortThe port that is Link is on or zero if the
link is not tied to a given port (e.g.
for ISDN incoming calls or Multilink
PPP that requires to run Multilink with
combined serial ports and ISDN calls on
the same slot, but not necessarily fixed
to a given ISDN port on that slot).
If type is wsmPort(1), this must be a non-zero
value.rw INTEGER .1.3.6.1.4.1.800.2.7.2.1.1.7 |
linkxModeThis object define whether the given link is to be
a On-Demand Link or it is use for Backup.rw Enumeration .1.3.6.1.4.1.800.2.7.2.1.1.8 |