XSWITCH-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for XSWITCH-MIB.
277
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
277 total| Object Name |
|---|
switchChip OBJECT IDENTIFIER .1.3.6.1.4.1.81.28 |
RFC1155-SMI Unknown .1.3.6.1.4.1.81.28 |
scGen OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1 |
scGenChassis OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1.1 |
scGenChMainAgPositionThis attribute defines the position in the chassis where the Main Agent resides.ro INTEGER .1.3.6.1.4.1.81.28.1.1.1 |
scGenChRedunAgPositionThis attribute defines the position in the chassis where the Redundant Agent resides.
0 means Redundant Agent not present.ro INTEGER .1.3.6.1.4.1.81.28.1.1.2 |
scGenChRedunAgActivityStatusThis attribute defines the status of the Redundant Agent.
notPresent(1) - indicates that no redundant Agent exists.
dormant(2) - indicates that the redundant Agent is ok and
may at any moment become the Agent of the system.
active(3) - indicates that the redundant Agent is acting as the Agent.ro Enumeration .1.3.6.1.4.1.81.28.1.1.3 |
scGenChAgVLANThe Virtual LAN number of the Agent's internal interface.
The value 0 means Generic ( But can communicate with Global !).
The values '255' mean Global.rw INTEGER .1.3.6.1.4.1.81.28.1.1.4 |
scGenMon OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1.2 |
scGenMonTableTable of attributes which define Monitoring information about
a single XSwitch in SC based devices. SEQUENCE OF ScGenMonEntry .1.3.6.1.4.1.81.28.1.2.1 |
scGenMonEntryAn entry in the table, containing data about a single XSwitch. ScGenMonEntry .1.3.6.1.4.1.81.28.1.2.1.1 |
scGenMonSwitchIdIndex which identifies the XSwitch for which this entry contains information.
This value is never greater than chNumberOfXSwitches.ro INTEGER .1.3.6.1.4.1.81.28.1.2.1.1.1 |
scGenMonDropEventsThe total number of events in which the probe could not
count packets due to lack of resources. This number is not
necessarily the number of packets dropped; it is just the number
of times this condition has been detected.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.2 |
scGenMonOctetsThe total number of good octets switched and error octets filtered by this XSwitch.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.3 |
scGenMonPktsThe total number of good packets switched and error
packets filtered by this XSwitch.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.4 |
scGenMonGoodBroadcastPktsThe total number of good packets switched by this
XSwitch that were directed to the broadcast address.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.5 |
scGenMonGoodMulticastPktsThe total number of good packets switched by this XSwitch that were
directed to the multicast address.
Note that this number does not include packets directed to the broadcast address.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.6 |
scGenMonGoodPktsThe total number of good packets switched by this XSwitch.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.7 |
scGenMonBadPktsThe total number of bad packets filtered by this XSwitch.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.8 |
scGenMonGoodOctetsThe total number of good octets switched by this XSwitch.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.9 |
scGenMonBadOctetsThe total number of bad octets filtered by this XSwitch.ro Counter .1.3.6.1.4.1.81.28.1.2.1.1.10 |
scGenMonSmonCapabilityThis item is used to define which smon's application are implemented in the agent.
When the console first performs smon application it should read this item in order
to know which of the smon's applications are available in this agent's version.
When there is a value of 0 (zero) in the relevant bit it means that the assosiated
application is not supported, When there is a value of 1 (one) in the relevant bit it
means that the assosiated application is supported.
D0 - Statistics.
D1 - History.
D2 - Alarms.
D3 - Host.
D4 - HostTopN.
D5 - Metrix.
D6 - Filter.
D7 - Capture.
D8 - Event.
D9 - TokenRing.
D10 - ProtocolDir.
D11 - ProtocolDist.
D12 - AddressMap.
D13 - NlHost.
D14 - NlMatrix.
D15 - AlHost.
D16 - AlMatrix.
D17 - UsrHistory.
D18 - ProbConfig.
D19 - Port.
D20 - PortTopN.
D21 - Subnet.
D22 - SubnetMatrix.
D23 - Vlan.
D24 - VlanMatrix.
D25 - nlHostTopN
D26 - portHistoryro OCTET STRING .1.3.6.1.4.1.81.28.1.2.1.1.11 |
scGenMonMIBCtrModeThis object defines for switch ports to include/exclude local segment traffic
in their port countersrw Enumeration .1.3.6.1.4.1.81.28.1.2.1.1.12 |
scGenMonSwitchVLANListA bitmap defining the status of the virtual LANs in the
Virtual LAN Table. The first bit is for Virtual LAN 0, the
second for Virtual LAN 1, and so on. If the Virtual LAN
exists in the hub the value of the associated bit is 1,
otherwise 0.ro OCTET STRING .1.3.6.1.4.1.81.28.1.2.1.1.13 |
scGenMonMIBCtrListA bitmap defining the status of the MIBCtrMode for
every group in the switch. The MSB (Most significant bit)
representing the status of group #1. If MIBCtrMode on a
group is enable(1) the bit is set to 1, otherwise 0.ro OCTET STRING .1.3.6.1.4.1.81.28.1.2.1.1.14 |
scGenMonTimeStampThis attribute contains the value of sysUpTime
at the time switch counters were calculated.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.28.1.2.1.1.15 |
scGenMonVlanTimeStampThis attribute contains the value of sysUpTime
at the time VLAN counters were calculated.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.28.1.2.1.1.16 |
scGenMonPriorityTableA list of priority count entries. SEQUENCE OF ScGenMonPriorityEntry .1.3.6.1.4.1.81.28.1.2.2 |
scGenMonPriorityEntryA list of statistics related to a specific priority level on
a single XSwitch in SC based devices. ScGenMonPriorityEntry .1.3.6.1.4.1.81.28.1.2.2.1 |
scGenMonPrioritySwitchIdIndex which identifies the XSwitch for which this entry contains information.
This value is never greater than chNumberOfXSwitches.ro INTEGER .1.3.6.1.4.1.81.28.1.2.2.1.1 |
scGenMonPriorityIdThe priority for which this entry reports statistics.
1=regular.
2=high.ro INTEGER .1.3.6.1.4.1.81.28.1.2.2.1.2 |
scGenMonPriorityGoodPktsThe total number of good packets switched by this XSwitch
using this packet priority level.ro Counter .1.3.6.1.4.1.81.28.1.2.2.1.3 |
scGenMonPriorityGoodOctetsThe total number of good octets switched by this XSwitch
using this packet priority level.ro Counter .1.3.6.1.4.1.81.28.1.2.2.1.4 |
scGenMonVLANListA bitmap defining the status of the virtual LANs in the
Virtual LAN Table. The first bit is for Virtual LAN 0, the
second for Virtual LAN 1, and so on. If the Virtual LAN
exists in the hub the value of the associated bit is 1, otherwise 0.ro OCTET STRING .1.3.6.1.4.1.81.28.1.2.3 |
scGenMonVLANTableA list of virtual LAN statistics. SEQUENCE OF ScGenMonVLANEntry .1.3.6.1.4.1.81.28.1.2.4 |
scGenMonVLANEntryA list of statistics related to a specific Virtual LAN. ScGenMonVLANEntry .1.3.6.1.4.1.81.28.1.2.4.1 |
scGenMonVLANSwitchIdIndex which identifies the XSwitch for which this entry contains information.
This value is never greater than chNumberOfXSwitches.ro INTEGER .1.3.6.1.4.1.81.28.1.2.4.1.1 |
scGenMonVLANIdThe Virtual LAN for which this entry contains information.ro INTEGER .1.3.6.1.4.1.81.28.1.2.4.1.2 |
scGenMonVLANGoodPktsThe total number of good packets switched by the XSwitch
on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.2.4.1.3 |
scGenMonVLANGoodOctetsThe total number of good octets switched by the XSwitch
on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.2.4.1.4 |
scGenMonVLANStatsUcastPktsThe total number of good unicast packets switched by the XSwitch
on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.2.4.1.5 |
scGenMonVLANStatsMcastPktsThe total number of good multicast packets switched by the XSwitch
on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.2.4.1.6 |
scGenMonVLANStatsBcastPktsThe total number of good broadcast packets switched by the XSwitch
on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.2.4.1.7 |
scGenMonSwitchesA bitmap defining the switch status, whether it is functional or not.
The list should start with the MSB.
Value of each bit:
0 - the switch is not functional
1 - the switch is functional
The mapping is:
Bit 0 : Left DomainX
Bit 1 : Right DomainXro OCTET STRING .1.3.6.1.4.1.81.28.1.2.5 |
scHostTimePortCorrTableAn addition to the RMON MIB's hostTimeTable. This table contains
a list of MAC addresses that were monitored on the switch
and the ports to which they are connected.
The index of this table is the same as for the standard RMON
hostTimeTable. Indexes are scHostTimeCreationOrder and scHostTimeIndex.
The MAC address is stored in scHostTimeAddress.
The port to which the MAC address is connected is defined in
scHostTimePortConnection. SEQUENCE OF ScHostTimePortCorrEntry .1.3.6.1.4.1.81.28.1.2.6 |
scHostTimePortCorrEntryAn entry in the MAC to port correlation table. ScHostTimePortCorrEntry .1.3.6.1.4.1.81.28.1.2.6.1 |
scHostTimeAddressThe physical address of this host.ro OCTET STRING .1.3.6.1.4.1.81.28.1.2.6.1.1 |
scHostTimeCreationOrderAn index that uniquely identifies an entry in
the hostTime table among those entries associated
with the same hostControlEntry. This index shall
be between 1 and N, where N is the value of
the associated hostControlTableSize. The ordering
of the indexes is based on the order of each entry's
insertion into the table, in which entries added
earlier have a lower index value than entries added
later. Thus the management station has the ability to
learn of new entries added to this table without
downloading the entire table.
It is important to note that the index for a
particular entry may change as an (earlier) entry
is deleted from the table. Because this order may
change, management stations should make use of the
hostControlLastDeleteTime variable in the
hostControlEntry associated with the relevant
portion of the hostTimeTable. By observing
this variable, the management station may detect
the circumstances where a download of the table
may have missed entries, and where a previous
association between a value of hostTimeCreationOrder
and a hostTimeEntry may no longer hold.ro INTEGER .1.3.6.1.4.1.81.28.1.2.6.1.2 |
scHostTimeIndexThe set of collected RMON host statistics of
which this entry is a part. The set of hosts
identified by a particular value of this
index is associated with the hostControlEntry
as identified by the same value of hostControlIndex.ro INTEGER .1.3.6.1.4.1.81.28.1.2.6.1.3 |
scHostTimePortConnectionThe switch port to which this scHostTimeAddress is connected.
The coding of the port number for Visage switches is:
32*(H-1)+P, where H is the number of the hub in the stack
and P the port in the hub (1.. 32).
For hosts whose port connection is not identified by the agent, the
value of this item will be 65,535ro INTEGER .1.3.6.1.4.1.81.28.1.2.6.1.4 |
scGenGroup OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1.3 |
scGenGroupTableTable of attributes which define general configuration
information about a single SC based group. SEQUENCE OF ScGenGroupEntry .1.3.6.1.4.1.81.28.1.3.1 |
scGenGroupEntryAn entry in the table, containing data about a single Group. ScGenGroupEntry .1.3.6.1.4.1.81.28.1.3.1.1 |
scGenGroupIdUnique Id of the group in the scGenGroupTable.
Equals the number of the slot by which the group is accessed.ro INTEGER .1.3.6.1.4.1.81.28.1.3.1.1.1 |
scGenGroupUseSwitchesThis attribute reflects the status of the `Use Switches' switch which
defines the working mode of the module.
on - The module works according to the switches. No Set commands
may be performed on attributes related to the switches.
off - Ignore Dip Switches, use stored parameters and accept all Set commands.ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.2 |
scGenGroupCopyPortSupportIndication whether a module supports Copy-Port [on(1)],
or does not support Copy-Port [off(2)].ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.3 |
scGenGroupXswitchConnectionThis attribute identifies the Xswitch number (1..4) to which the module
is connected to.
In non-bridged configuration, there are potentialy up to 4 Xswitches -
1&2 for left&right Ethernet Xswitches and 3&4 for left&right TR Xswitches.
In bridged configuration, there are potentialy 2 Xswitches -
1 for Ethernet Xswitch and 2 for TR Xswitch.ro INTEGER .1.3.6.1.4.1.81.28.1.3.1.1.4 |
scGenGroupStatusThis attributes defines the status of the Xswitch module.
The value 'loadsBudgetProblem' indicates that the module cannot be connected to the
Xswitch because it exceeds the maximum number of loads allowed in the Xswitch.ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.5 |
scGenGroupSwitchTypeThis attribute defines the Xswitch type of the module.ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.6 |
scGenGroupNumberOfLoadsThis attribute identifies the number of loads which that Xswitch module represents.ro INTEGER .1.3.6.1.4.1.81.28.1.3.1.1.7 |
scGenGroupSetDefaultsSet all module and ports parameters in the XSwitch module, to their default values.
This item will always return a value of off(2), since it acts like a toggle switch.
Set of layer2Only(3) value, will cause partial setting, to layer2 parameters onlyrw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.8 |
scGenGroupSupportCopyPortListA bitmap defining the status of each port of the hub\module whether it support copy
port or not,
0 - the port does not support copy port
1 - the port support the copy port
the list should start with the MSB indicates port number 1 (one) and the LSB
indicates the highest number of the ports in the hub\module.
For Example: if a module\hub has 8 ports and ports number 1,3,4 support copy
port while the other don't, the bitmap will be: 10110000.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.1.1.9 |
scGenGroupSupportPortCountersListA bitmap defining the status of each port of the hub\module whether it supports
the port's counters,
0 - the port does not support port's counters
1 - the port support the port's counters
the list should start with the MSB indicates port number 1 (one) and the LSB
indicates the highest number of the ports in the hub\module.
For Example: if a module\hub has 8 ports and ports number 1,3,4 support
port's counters while the other don't, the bitmap will be: 10110000.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.1.1.10 |
scGenGroupSupportSegCountersListA bitmap defining the status of each port of the hub\module whether it supports
the segment counters on port,
0 - the port does not support segment's counters
1 - the port support the segment's counters
the list should start with the MSB indicates port number 1 (one) and the LSB
indicates the highest number of the ports in the hub\module.
For Example: if a module\hub has 8 ports and ports number 1,3,4 support
segment's counters while the other don't, the bitmap will be: 10110000.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.1.1.11 |
scGenGroupUpLinkTypeThe type of the Up Link port
Relevant only for the 25th port of Visage 2500:
Fiber (1) - 100BaseFX,
Copper (2) -100BaseTX.rw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.12 |
scGenGroupPlugInTypeAttribute describing the type of the plug-in modulero Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.13 |
scGenGroupPlugInDescrDescriptor of the plug-in in ASCII (readable) format,
mainly for use with Generic management applications.ro DisplayString .1.3.6.1.4.1.81.28.1.3.1.1.14 |
scGenGroupPlugInCSASCII string for description and display of the plug-in
module configuration symbol. The format of the number is XXXX.YYro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.81.28.1.3.1.1.15 |
scGenGroupDefaultVLANAttribute describing the Default VLAN configuration on the switch ports of the module.
It is determined according to scGenSwitchDefaultVLAN parameter of the agent.ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.16 |
scGenGroupCascadingTypeAttribute describing the type of the cascding modulero Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.17 |
scGenGroupCascadingDescrDescriptor of the cascading module in ASCII (readable) format,
mainly for use with Generic management applications.ro DisplayString .1.3.6.1.4.1.81.28.1.3.1.1.18 |
scGenGroupCascadingCSASCII string for description and display of the cascading module
configuration symbol. The format of the number is XXX.YYYro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.81.28.1.3.1.1.19 |
scGenGroupSupportDstCopyPortListA bitmap defining the status of each port of the hub\module
whether it supports the capability of being a destination copy-port .
1 - the port has the capability of being a destination copy-port
0 - the port does not have the capability of being a destination copy-port
The list should start with the MSB indicating port number 1 (one)
and the LSB indicating the highest number of the ports in the hub\module.
For Example: if a module\hub has 8 ports and ports number 1,3,4 can be
destination copy ports, while the others cannot, then the bitmap will be: 10110000.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.1.1.20 |
scGenGroupBUPSTypeAttribute describing the type of the BUPS modulero Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.21 |
scGenGroupBUPSCSASCII string for description and display of the BUPS
module configuration symbol. The format of the number is X.Yro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.81.28.1.3.1.1.22 |
scGenGroupBUPSFansStatusThe operational status of the fans included in the BUPS module:
allFansOK(1) - all BUPS module's fans are operational.
oneFanFailed(2) - at least one of the BUPS module's fan is failed.ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.23 |
scGenGroupFansStatusThe operational status of the fans included in the module:
allFansOK(1) - all module's fans are operational.
oneFanFailed(2) - at least one of the module's fan is failed.ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.24 |
scGenGroupInternalBufferingControl the internal buffering capacity.rw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.25 |
scGenGroupMcFilterBoxSupportTells whether the box hardware supports filtering or not.ro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.26 |
scGenGroupMcFilterPersonalitySupportTells whether the personality hardware supports filtering or not.
The value PersonalityNotInstalld means that the a personality
Extention was not installed in the specific boxro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.27 |
scGenGroupMcFilterStackingSupportTells whether the stacking hardware supports filtering or not
The value StackingNotInstalld means that the a stacking daughter board
was not installed in the specific boxro Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.28 |
scGenGroupLACPModeThe value of this attribute determines whether LACPDU messages can be exchanged by the module's ports.
If enabled, the ports will exchange LACPDU messages according to their scGenPortLACPMode MIB.
If disabled, every port of the module will not exchange LACPDU messages - regardless of there
scGenPortLACPMode MIB.
This MIB is required for internal communication between the agent and its sub-agents, in order to distribute
throughout the switch's modules the setting made on the scGenSwitchLACPMode MIB.rw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.29 |
scGenGroupSecurityModeGroup intrusion security mode assigned to this module.
securityMode - all ports in this module are secure according to their scGenPortSecurityMode MIB's value.
nonSecurityMode - all ports in this module are not secure.rw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.30 |
scGenGroupBroadcastStormControlSet the Broadcast Storm Control function on all switch ports.
On means that Broadcast, Multicast or Unknown packets are discarded on an ingress port,
when the rate of those packets, received on the port,
is above the scGenGroupBroadcastThreshold, as set by the user.rw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.31 |
scGenGroupBroadcastThresholdSet the Rate Threshold, in packets per second, above which Broadcast,
Multicast or Unknown packets are discarded on ingress port.rw INTEGER .1.3.6.1.4.1.81.28.1.3.1.1.32 |
scGenGroupPriorityQueuesSchedulingSet the Priority Queues Scheduling scheme for packets transmission from egress ports.
Strict - will serve higher priority queue before lower priority queue, as long as the higher queue has packets.
Weighted - will serve higher priority queue before lower priority queue,
but will save specific bandwidth for each queue in order to avoid starvation of lower priority queues.rw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.33 |
scGenGroupBoundedDelaySet the Bounded Delay function in the switch.
On will ensure that time-sensitive packets will be forwarded
through the switch in no more than a maximum delay.rw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.34 |
scGenGroupSLDAdminStatusset the Self Loop Discovery application to enable/disable.
This works with the scGenPortSLDAdminStatusrw Enumeration .1.3.6.1.4.1.81.28.1.3.1.1.35 |
scGenGroupSmonTableTable of smon capabilities in a single group. SEQUENCE OF ScGenGroupSmonEntry .1.3.6.1.4.1.81.28.1.3.2 |
scGenGroupSmonEntryAn entry in the table, containing data about
a single Group. ScGenGroupSmonEntry .1.3.6.1.4.1.81.28.1.3.2.1 |
scGenGroupSmonGroupIdUnique Id of the group in the scGenGroupSmonTable.
Equals the number of the slot by which the group
is accessed.ro INTEGER .1.3.6.1.4.1.81.28.1.3.2.1.1 |
scGenGroupSmonCapabilityThis item is used to define which smon's application are
implemented in the group.
When there is a value of 0 (zero) in the relevant bit
it means that the assosiated application is not supported.
When there is a value of 1 (one) in the relevant bit it
means that the assosiated application is supported.
D0 - Statistics.
D1 - History.
D2 - Alarms.
D3 - Host.
D4 - HostTopN.
D5 - Metrix.
D6 - Filter.
D7 - Capture.
D8 - Event.
D9 - TokenRing.
D10 - ProtocolDir.
D11 - ProtocolDist.
D12 - AddressMap.
D13 - NlHost.
D14 - NlMatrix.
D15 - AlHost.
D16 - AlMatrix.
D17 - UsrHistory.
D18 - ProbConfig.
D19 - Port.
D20 - PortTopN.
D21 - Subnet.
D22 - SubnetMatrix.
D23 - Vlan.
D24 - VlanMatrix.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.2.1.2 |
scGenGroupSmonVlanListA bitmap defining the status of the virtual LANs in the
Virtual LAN Table. The first bit is for Virtual LAN 0, the
second for Virtual LAN 1, and so on. If the Virtual LAN
exists in the hub the value of the associated bit is 1, otherwise 0.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.2.1.3 |
scGenGroupSmonDropEventsThe total number of events ,in this group, in which the
probe could not count packets due to lack of resources.
This number is not necessarily the number of packets
dropped; it is just the number of times this condition
has been detected.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.4 |
scGenGroupSmonGoodBroadcastPktsThe total number of good broadcast packets in this group,
switched by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.5 |
scGenGroupSmonGoodMulticastPktsThe total number of good multicast packets, in this group,
switched by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.6 |
scGenGroupSmonGoodPktsThe total number of good packets, in this group, switched by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.7 |
scGenGroupSmonBadPktsThe total number of bad packets , in this group, filtered by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.8 |
scGenGroupSmonGoodOctetsThe total number of good octets, in this group, switched by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.9 |
scGenGroupSmonBadOctetsThe total number of bad octets, in this group, filtered by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.10 |
scGenGroupSmonPktsThe total number of packets, good and bad, in this group,
switched by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.11 |
scGenGroupSmonOctetsThe total number of octets, good and bad, in this group,
switched by the Xswitch.ro Counter .1.3.6.1.4.1.81.28.1.3.2.1.12 |
scGenGroupSmonMIBCtrModeThis object defines for group ports to include/exclude
local segment traffic in their port countersrw Enumeration .1.3.6.1.4.1.81.28.1.3.2.1.13 |
scGenGroupVlanTableTable of attributes which define general VLAN
counters of a single SC based group. SEQUENCE OF ScGenGroupVlanEntry .1.3.6.1.4.1.81.28.1.3.3 |
scGenGroupVlanEntryAn entry in the table, containing VLAN counters in a single Group. ScGenGroupVlanEntry .1.3.6.1.4.1.81.28.1.3.3.1 |
scGenGroupVlanGroupIdUnique Id of the group in the scGenGroupVlanTable.
Equals the number of the slot by which the group is accessed.ro INTEGER .1.3.6.1.4.1.81.28.1.3.3.1.1 |
scGenGroupVlanIdThe Virtual LAN for which this entry contains information.ro INTEGER .1.3.6.1.4.1.81.28.1.3.3.1.2 |
scGenGroupVlanUcastPktsThe total number of good unicast packets ,in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.3 |
scGenGroupVlanMcastPktsThe total number of good multicast packets ,in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.4 |
scGenGroupVlanBcastPktsThe total number of good broadcast packets in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.5 |
scGenGroupVlanGoodPktsThe total number of good packets ,in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.6 |
scGenGroupVlanGoodOctetsThe total number of good octets ,in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.7 |
scGenGroupVlanUcastOctetsThe total number of good unicast octets ,in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.8 |
scGenGroupVlanMcastOctetsThe total number of good multicast octets ,in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.9 |
scGenGroupVlanBcastOctetsThe total number of good broadcast octets ,in this group,
switched by the Xswitch on this Virtual LAN.ro Counter .1.3.6.1.4.1.81.28.1.3.3.1.10 |
scGenGroupVlanCurrentEgressPortsThe set of ports in this module which are transmitting traffic for this
vlan as either tagged or untagged frames. Each module's port is
represented by a single bit in this 128-bits bitmap according to the
PortList convention of RFC2674.
This MIB is for internal agent sub-agent communication, it is aimed to
distribute the standard dot1qVlanCurrentEgressPorts among the modules.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.3.1.11 |
scGenGroupVlanCurrentUntaggedPortsThe set of ports which are transmitting traffic for this VLAN as
untagged frames. Each module's port is
represented by a single bit in this 128-bits bitmap according to the
PortList convention of RFC2674.
This MIB is for internal agent sub-agent communication, it is aimed to
distribute the standard dot1qVlanCurrentUntaggedPorts among the modules.
It is updated together with genPortVLANMode MIB.ro OCTET STRING .1.3.6.1.4.1.81.28.1.3.3.1.12 |
scGenGroupVlanStaticEgressPortsThe set of ports in this module which are permanently assigned to the
egress list for this VLAN by management. Each module's port is
represented by a single bit in this 128-bits bitmap according to the
PortList convention of RFC2674. Changes to a bit in this object affect
the per-port per-VLAN Registrar control for Registration Fixed for the
relevant GVRP state machine on each port. The default value of this
object is a string of zeros long by 128 bits, indicating not fixed.
This MIB is for internal agent sub-agent communication, it is aimed to
distribute the standard dot1qVlanStaticEgressPorts among the modules.rw OCTET STRING .1.3.6.1.4.1.81.28.1.3.3.1.13 |
scGenGroupVlanStaticUntaggedPortsThe set of ports which should transmit egress packets for this VLAN as
untagged. Each module's port is represented by a single bit in this
128-bits bitmap according to the PortList convention of RFC2674.
The default value of this object for the default VLAN (dot1qVlanIndex =
1) is a string of appropriate length including all ports. There is no
specified default for other VLANs. If a device agent cannot
support the set of ports being set then it will reject the
set operation with an error. An example might be if a
manager attempts to set more than one VLAN to be untagged
on egress where the device does not support this IEEE 802.1Q
option. It is updated together with genPortVLANMode MIB.rw OCTET STRING .1.3.6.1.4.1.81.28.1.3.3.1.14 |
scGenGroupRspTable. SEQUENCE OF ScGenGroupRspEntry .1.3.6.1.4.1.81.28.1.3.4 |
scGenGroupRspEntry. ScGenGroupRspEntry .1.3.6.1.4.1.81.28.1.3.4.1 |
scGenGroupRspGroupIdUnique Id of the group in the scGenGroupRspTable.
Equals the number of the slot by which the group is accessed.ro INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.1 |
scGenGroupRspHelloIntervalThe interval between transmissions of hello-messages, in 100mSec units.rw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.2 |
scGenGroupRspDevicePollingIntervalThe interval between transmissions of ARP queries for polling
connectivity to the device, in 100mSec units.rw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.3 |
scGenGroupRspDeviceNotRespondingTimeoutAmount of time in which no ARP-replies are received from the device,
which cause the RSP to assume no connection to that device, in 100mSec units.rw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.4 |
scGenGroupRspSwitchNotRespondingTimeoutAmount of time in which no hello-messages with acknowledge are received from the other switch,
which cause the RSP to assume no connection to that switch, in 100mSec units.rw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.5 |
scGenGroupRspMoveToForwardingIntervalAmount of time the port waits upon deciding to move to forwarding mode,
until it moves to that mode, in 100mSec units.rw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.6 |
scGenGroupRspBroadcastArpShortIntervalThe interval in which the switch should send broadcast ARPs to the device
when not knowing the MAC-address of the device, in 100mSec units.rw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.7 |
scGenGroupRspBroadcastArpShortIntervalNumberThe number of broadcast ARPs the switch should send in short interval time,
when not knowing the MAC address of the devicerw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.8 |
scGenGroupRspBroadcastArpLongIntervalThe interval in which the switch should send broadcast ARPs to the device
when the device does not respond to unicast ARPs, in 100mSec units.rw INTEGER .1.3.6.1.4.1.81.28.1.3.4.1.9 |
scGenGroupRspPeriodicPingsBoxIpAddressThis MIB-item is the IP-address that the P330 box uses in order to periodically ping to devices
Default value for IP Address is 0.0.0.0rw IpAddress .1.3.6.1.4.1.81.28.1.3.4.1.10 |
scGenGroupRspPeriodicPingsDestinationIpAddressThis MIB-item sets an IpAddress that the devices will be configured to periodically ping to.
The switch will be responsible to reply to ARP-queries concerning this IP-address,
and which were issued by devices directly attached to it.
A value of 0.0.0.0 in this Mib Item means that it does not describe an existing IpAddress.
Default value for IP Address is 0.0.0.0rw IpAddress .1.3.6.1.4.1.81.28.1.3.4.1.11 |
scGenGroupRspModeSets the mode of the module from the RSP-application prespective. Possible modes are:
RSP-module-mode-role-A - means that the ports of this module perform the
RSP scheme for a device connected through a repeater, in role A (primary role).
RSP-module-mode-role-B - means that the ports of this module perform the
RSP scheme for a device connected through a repeater, in role B (secondary role).rw Enumeration .1.3.6.1.4.1.81.28.1.3.4.1.12 |
scGenPort OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1.4 |
scGenPortTableTable of attributes which define general configuration
information about a single SC based port. SEQUENCE OF ScGenPortEntry .1.3.6.1.4.1.81.28.1.4.1 |
scGenPortEntryAn entry in the table, containing data about a single Port. ScGenPortEntry .1.3.6.1.4.1.81.28.1.4.1.1 |
scGenPortGroupIdId of the group to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.28.1.4.1.1.1 |
scGenPortIdUnique Id of the port in the scEthPortTable.ro INTEGER .1.3.6.1.4.1.81.28.1.4.1.1.2 |
scGenPortVLANThe Virtual LAN number of the Port.
The value 0 means Generic ( But can communicate with Global !).
The value '255' means Global.rw INTEGER .1.3.6.1.4.1.81.28.1.4.1.1.3 |
scGenPortPriorityThe priority level of the packets send by the Port.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.4 |
scGenPortSetDefaultsSet all port parameters in the XSwitch module, to their default values.
This item is used for ports that are managed by Sub-agents.
This item will always return a value of off(2), since it acts
like a toggle switch.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.5 |
scGenPortBackboneThe type of the Xswitch port. 'on' indicates that the port was discovered
by VIDP as backbone port.ro Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.6 |
scGenPortCopyModeEnable /Disable the Copy Port mode in the Sub-Agent.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.7 |
scGenPortCopyDestinationThe destination of the copied information.
The destination can be another port or the Agent acting as an RMON probe.
The value of this item is: LSB Byte= sniffer channel number,
Next Byte= sniffer device number.
When sniffer device number=31, the destination is the Agent.rw INTEGER .1.3.6.1.4.1.81.28.1.4.1.1.8 |
scGenPortLinkAggregationNumberThe Link Aggregation Group (LAG) number, to which the Port belongs.
The value 0 means that this port is not part of a LAG. This is also the default.rw INTEGER .1.3.6.1.4.1.81.28.1.4.1.1.9 |
scGenPortSendBridgedPacketsWhen set to on(1), the port will transmit to the line bridged frames
(for which their secondary VLAN was 0xFFE internally).
This is the case for ports connected to a station or to another switch
that has no bridging capabilities. When set to off(2), the port will reject
the bridged frames, by not sending them to the line.
This is the case for ports connected to another switch that has its own bridging capabilities.
Default value is on(1).rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.10 |
scGenPortVLANEgressStaticConfigurationA bitmap defining the VLANs, for which the port is member in their Egress Tables.
The first bit is for VLAN 0, the second bit for VLAN 1, and so on.
If the port is member in the Egress Table of a specified VLAN,
then the value of the associated bit is 1, otherwise 0.
The actual VLAN Table configuration, according to this item,
is done only when scGenPortStaticVLANBinding is enabled.rw OCTET STRING .1.3.6.1.4.1.81.28.1.4.1.1.11 |
scGenPortStaticVLANBindingThis object defines whether Static VLAN Binding is enabled or disabled on the port.
If enabled, the port is member in the Egress List of the VLANs, as specified in
scGenPortVLANEgressStaticConfiguration, in addition to its Port VLAN.
If disabled, the port is member in the Egress List of the VLANs,
according to the VLAN Tagging mode of the port - i.e. if VLAN Tagging mode is Clear,
then the Port is member in the Egress List of only the Port VLAN.
If VLAN Tagging mode is 802.1Qtagging, then the Port is member in the Egress List of all VLANs.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.12 |
scGenPortSecIdThe identification number (per module) of the switching chip to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.28.1.4.1.1.13 |
scGenPortMaxLagsOnSecThe theoretic maximum number of LAGs that can be defined over the switching chip to which the port
belongs. The value is fixed according to the switching chip type:
For the Timpani chip, the value is 1.
For the Guitar chip, the value is 2.ro INTEGER .1.3.6.1.4.1.81.28.1.4.1.1.14 |
scGenPortGenericTrapThe value of this attribute determines whether or not the agent sends the snmp generic traps 2 and 3,
for link down/up events on this port.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.15 |
scGenPortLACPModeThe value of this attribute determines whether the port exchanges LACPDU messages,
in agreement with the scGenGroupLACPMode MIB.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.16 |
scGenPortLastIntruderSourceAddrEthernet source address of the last intrusion attempt at this port.
The value of this item will be 000000 (a string of 6 zeros) if security mode is
disable or no security violation at this port.ro OCTET STRING .1.3.6.1.4.1.81.28.1.4.1.1.17 |
scGenPortSecurityModeSecurity mode assigned to this port.
nonSecurityMode - do not perform intrusion control security mechanism on this port.
securityMode - perform intrusion control security mechanism and trap the console
in case of security violation,
if both scGenGroupSecurityMode and scGenSwitchSecurityMode are in this mode too.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.18 |
scGenPortSTAEnable /Disable the Spanning Tree protocol for this port,
meaningless when disabled at the switch level via the scGenSwitchSTA MIB.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.19 |
scGenPortLagCapabilityAn octet string with the size of the maximum number of LAGs on the device.
Each bit represents a LAG which the port may be associated with (a member of).ro OCTET STRING .1.3.6.1.4.1.81.28.1.4.1.1.20 |
scGenPortCapabilityPort capability bit mask, where each bit represent the capability of the port:
Bit #1 - 10Mbps speed support
Bit #2 - 100Mbps speed support
Bit #3 - 1000Mbps speed support
Bit #4 - 10000Mbps speed support
Bit #9 - 2 queues support
Bit #10 - 4 queues support
Bit #11 - 8 queue support
Bit #17 - CopyPort Tx support
Bit #18 - CopyPort Rx support
Bit #19 - CopyPort Tx&Rx support
Bit #20 - CopyPort filtering support
Bit #25 - Symmetric FC support
Bit #26 - AsymmetricTx FC support
Bit #27 - AsymmetricRx FC supportro OCTET STRING .1.3.6.1.4.1.81.28.1.4.1.1.21 |
scGenPortSLDAdminStatusSets the admin status of each port in the Self Loop Discovery application
A port which is disbaled does not send LDDU . A port which is enabled sends
LDDU and migth turn to blocking if a SLD is discovered.rw Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.22 |
scGenPortSLDStatusA port which is SLDEnabled can be in SelfLoop or NoSelfLoop mode .
if the port is SLD disabled it will return notSupported.ro Enumeration .1.3.6.1.4.1.81.28.1.4.1.1.23 |
scGenPortRspTableTable of attributes which define general configuration
information about a single SC based port. SEQUENCE OF ScGenPortRspEntry .1.3.6.1.4.1.81.28.1.4.2 |
scGenPortRspEntryAn entry in the table, containing data about a single Port. ScGenPortRspEntry .1.3.6.1.4.1.81.28.1.4.2.1 |
scGenPortRspGroupIdId of the group to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.28.1.4.2.1.1 |
scGenPortRspIdUnique Id of the port in the scGenPortRspTable.ro INTEGER .1.3.6.1.4.1.81.28.1.4.2.1.2 |
scGenPortRspModeSets the mode of the port from the RSP-application perspective. Possible modes are:
Regular - means that this is a regular port that does not participate in the RSP scheme,
RSP-mode-role-A - means that this port performs the RSP
scheme for a device connected through a repeater, in role A (primary role).
RSP-mode-role-B - means that this port performs the RSP
scheme for a device connected through a repeater, in role B (secondary role).
device-mode - means that this port performs the RSP scheme for a device with two interfaces.rw Enumeration .1.3.6.1.4.1.81.28.1.4.2.1.3 |
scGenSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1.5 |
scGenSwitchTableTable of attributes which define information about
a single XSwitch in SC based devices. SEQUENCE OF ScGenSwitchEntry .1.3.6.1.4.1.81.28.1.5.1 |
scGenSwitchEntryAn entry in the table, containing data about a single XSwitch. ScGenSwitchEntry .1.3.6.1.4.1.81.28.1.5.1.1 |
scGenSwitchIdIndex which identifies the XSwitch for which this entry contains information.
This value is never greater than chNumberOfXSwitches.ro INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.1 |
scGenSwitchCopyModeEnable /Disable the Copy Port mode in the XSwitch.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.2 |
scGenSwitchCopySourceThe port in the switch that is being copied.
All received and transmit packets on the port( including local traffic ) are copied to
the defined destination, besides their normal destination.
The value of this item is: 1024*S+P,
where S is the slot number in the hub and P the port within the slot.rw INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.3 |
scGenSwitchCopyDestinationThe destination of the copied information.
The destination can be another port or the Agent acting as an RMON probe.
The value of this item is: 1024*S+P,
where S is the slot number in the hub and P is the port within the slot.
Value 1023 means that the destination is the Agent.rw INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.4 |
scGenSwitchSetDefaultsSet all port parameters in the XSwitch, to their default values.
This item will always return a value of off(2), since it acts like a toggle switch.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.5 |
scGenSwitchVIDPEnable /Disable the VIDP protocol supported in the XSwitch.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.6 |
scGenSwitchTypeThis attribute defines the type of the Xswitch.ro Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.7 |
scGenSwitchMasterIdThis attribute defines which module in the Xswitch take the role of the Master.
It is equal to the slot number of the Xswitch Master.ro INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.8 |
scGenSwitchResetSetting this attribute to `on' will cause a reset to the Xswitch. Default value is 'off'.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.9 |
scGenSwitchNumberOfLoadsThis attribute identifies the total number of loads of that Xswitch.
There is a maximum budget of 30 loads on an single Xswitch.ro INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.10 |
scGenSwitchAgVLANThe Virtual LAN number of the Agent's internal interface in the switch.
The value 0 means Generic (But can communicate with Global !).
The value '255' means Global.rw INTEGER (0.. 4095) .1.3.6.1.4.1.81.28.1.5.1.1.11 |
scGenSwitchVLANListA bitmap defining the status of the virtual LANs in the
Virtual LAN Table. The first bit is for Virtual LAN 0, the
second for Virtual LAN 1, and so on. If the Virtual LAN
exists in the hub the value of the associated bit is 1, otherwise 0.ro OCTET STRING .1.3.6.1.4.1.81.28.1.5.1.1.12 |
scGenSwitchSTAEnable /Disable the Spanning Tree protocol support in the switch.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.13 |
scGenSwitchSecurityModeThis item defines the Security mode per stack.
nonSecurityMode - all ports in the stack are not secure.
securityMode - all ports in the stack are secure according to their scGenPortSecurityMode MIB's value.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.14 |
scGenSwitchFindQueryAn address to be searched for by the Agent.
The Agent will start look for the address when the value is
different than Null.
The string format is:
1st byte: address type - 0=MAC, 1=IP
Next bytes: the address. (for MAC: next 6 bytes,
for IP: next 4 bytes).rw OCTET STRING .1.3.6.1.4.1.81.28.1.5.1.1.15 |
scGenSwitchFindResultThe search result. The result string format is:
1st byte: address type - 0=MAC, 1=IP.
Next bytes: the address. (for MAC: next 6 bytes,
for IP: next 4 bytes)
7-th byte (for MAC) or 5-th byte (for IP): number of ports with
the specified address.
Every next two bytes will indicate the slot and port number.
8-th byte (for MAC) or 6-th byte (for IP): slot number.
9-th byte (for MAC) or 7-th byte (for IP): port number. Etc.
If the specified address was NOT found, the result will be
with the 7-th byte (for MAC) or 5-th byte (for IP): byte equal to _0_.ro OCTET STRING .1.3.6.1.4.1.81.28.1.5.1.1.16 |
scGenSwitchSWRdChangeA 4-byte octet-string indicating a change performed by the SW Redundancy task.
The string will include:
Byte 1: Group1 (module number).
Byte 2 : Port1
Byte 3 : Group2
Byte 4 : port2
Where group2 port2 are the new enabled port.rw OCTET STRING .1.3.6.1.4.1.81.28.1.5.1.1.17 |
scGenSwitchDefaultVLANAttribute describing the Default VLAN configuration on the switch ports.
The user may change the value of this parameter through the setup terminal.
Vlan1 is the standard default VLAN for port configuration.ro Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.18 |
scGenSwitchVLANBridgingVLAN Bridging mode should be enabled in all Xswitches in the network, when the user
wants to support network-wide VLAN Bridging. VLAN Bridging should also be enabled
in one M-MLS, and PLS-Tagging mode should be set on the backbone ports.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.19 |
scGenSwitchOldVersionModulesA list of modules, in ASCII format, that have older software versions than
necessary in the switch. Module numbers are separated by a comma and a space.
It is used to inform the user on version inconsistency.ro DisplayString .1.3.6.1.4.1.81.28.1.5.1.1.20 |
scGenSwitchVIDPNonSupportedModulesA list of modules, in ASCII format, that do not support the VIDP function.
Module numbers are separated by a comma and a space.
It is used to inform the user on possible problems in VIDP function,
as not all modules in the switch support VIDP.ro DisplayString .1.3.6.1.4.1.81.28.1.5.1.1.21 |
scGenSwitchSTANonSupportedModulesA list of modules, in ASCII format, that do not support the STA function.
Module numbers are separated by a comma and a space.
It is used to inform the user on possible problems in STA function,
as not all modules in the switch support STA.ro DisplayString .1.3.6.1.4.1.81.28.1.5.1.1.22 |
scGenSwitchIDSNonSupportedModulesA list of modules, in ASCII format, that do not support the IDS function.
Module numbers are separated by a comma and a space.
It is used to inform the user on possible problems in IDS function,
as not all modules in the switch support IDS.ro DisplayString .1.3.6.1.4.1.81.28.1.5.1.1.23 |
scGenSwitchMcFilterEnable/disable the multicast filtering mechanism supported in the switchrw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.24 |
scGenSwitchMcFilterHostAgingTimeThe Value of the Host-Aging-Time parameter used by the multicast filtering
mechanism for aging learned multicast filtering informationrw INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.25 |
scGenSwitchMcFilterRouterAgingTimeThe Value of the Router-Aging-Time parameter used by the multicast filtering
mechanism for aging learned router-ports informationrw INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.26 |
scGenSwitchMcFilterDelayTimeThe Value of the Delay-Time parameter used by the multicast filtering
mechanism for waiting to all registration requests before applying a filter
on a specific grouprw INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.27 |
scGenSwitchLACPModeThe value of this attribute determines whether LACPDU messages can be exchanged by the switch's ports.
If enabled, the ports will exchange LACPDU messages according to their scGenPortLACPMode MIB.
If disabled, every port of the switch will not exchange LACPDU messages -
regardless of their scGenPortLACPMode MIB.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.28 |
scGenSwitchSecurityModePermitThis item defines the Security mode per switch.
This MIB is encoded in Lucent specific security mechanism.rw INTEGER .1.3.6.1.4.1.81.28.1.5.1.1.29 |
scGenSwitchFastAgingOnRemoteTopChgThis item defines if the switch performs fast aging on the MAC address
forwarding database (or reset the cam contents) upon reception of
Topology Change BPDU from the STA root, indicating that a remote
topology change has occurred. Local topology changes that occur on
valuable ports always generate a fast aging anyway.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.30 |
scGenSwitchGigaModeThe value of this attribute determines the setting for the two Giga links of a P130 stack.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.31 |
scGenSwitchCAMClearWhen value sets to on(1), the switch clears its CAM table.
This item will always return a value of off(2), since it acts like a toggle switch.rw Enumeration .1.3.6.1.4.1.81.28.1.5.1.1.32 |
scGenLinkAggregation OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1.6 |
scGenLinkAggregationTableTable of attributes which define Link Aggregation Group in a single switch. SEQUENCE OF ScGenLinkAggregationEntry .1.3.6.1.4.1.81.28.1.6.1 |
scGenLinkAggregationEntryAn entry in the table, containing LAG information in a single switch. ScGenLinkAggregationEntry .1.3.6.1.4.1.81.28.1.6.1.1 |
scGenLinkAggregationIdThe Link Aggregation number for which this entry contains information.ro INTEGER .1.3.6.1.4.1.81.28.1.6.1.1.1 |
scGenLinkAggregationNameThe Link Aggregation name, given by the user.rw DisplayString .1.3.6.1.4.1.81.28.1.6.1.1.2 |
scGenLinkAggregationBasePortGroupIdThe slot/unit number of the Base Port for this Link Aggregation.rw INTEGER .1.3.6.1.4.1.81.28.1.6.1.1.3 |
scGenLinkAggregationBasePortIdThe port number in the slot/unit of the Base Port for this Link Aggregation.rw INTEGER .1.3.6.1.4.1.81.28.1.6.1.1.4 |
scGenLinkAggregationNumberOfPortsThe current number of ports that belong to this Link Aggregation.ro INTEGER .1.3.6.1.4.1.81.28.1.6.1.1.5 |
scGenLinkAggregationLogicalPortGroupIdThe slot number of the logical port, representing this Link Aggregation.
All parameters for the LAG are managed through that logical port.ro INTEGER .1.3.6.1.4.1.81.28.1.6.1.1.6 |
scGenLinkAggregationLogicalPortIdThe logical port number in the slot, representing this Link Aggregation.
All parameters for the LAG are managed through that logical port.ro INTEGER .1.3.6.1.4.1.81.28.1.6.1.1.7 |
scGenLinkAggregationFunctionalStatusThe functional status of the LAG:
ok(1) - fully functional LAG, transmitting and receiving packets on all its ports.
fail(2) - all ports in the LAG are not in ok status.
partialFail(3) - some of the ports in the LAG are not in ok status.ro Enumeration .1.3.6.1.4.1.81.28.1.6.1.1.8 |
scGenLinkAggregationAutoNegResultsThe auto-negotiation results for speed and duplex for the LAG ports:
ok(1) - all ports resolved the same speed and duplex mode after auto-negotiation process.
autoNegInconsistantResults(2) - not all ports resolved the same speed and duplex mode after auto-negotiation process.ro Enumeration .1.3.6.1.4.1.81.28.1.6.1.1.9 |
scGenLinkAggregationFaultMaskEach bit of this item describes the situation of the LAG
regarding specific fault:
bit 1: on indicates 'LAG connection lost' when
scGenLinkAggregationFunctionalStatus=fail(2)
bit 2: on indicates 'LAG partial connection' when
scGenLinkAggregationFunctionalStatus=partailFail(3)
bit 3: on indicates 'LAG auto-neg inconsistant results' when
scGenLinkAggregationAutoNegResults= autoNegInconsistantResults(2)ro OCTET STRING .1.3.6.1.4.1.81.28.1.6.1.1.10 |
scGenLinkAggregationStatusThe status of this scGenLinkAggregation entry. According to RMON-2 standard (RFC 2021).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.28.1.6.1.1.11 |
scGenPortIPAddressRsp OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.1.7 |
scGenPortIPAddressRspTableTable of attributes which define general configuration
information about a single SC based port. SEQUENCE OF ScGenPortIPAddressRspEntry .1.3.6.1.4.1.81.28.1.7.1 |
scGenPortIPAddressRspEntryAn entry in the table, containing data about a single Port. ScGenPortIPAddressRspEntry .1.3.6.1.4.1.81.28.1.7.1.1 |
scGenPortIPAddressRspGroupIdId of the group to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.28.1.7.1.1.1 |
scGenPortIPAddressRspPortIdUnique Id of the port in the scGenPortRspTable.ro INTEGER .1.3.6.1.4.1.81.28.1.7.1.1.2 |
scGenPortIPAddressRspIpAddressIndexUnique Id of the port in the scGenPortRspTable.ro INTEGER .1.3.6.1.4.1.81.28.1.7.1.1.3 |
scGenPortIPAddressRspIpAddressThis MIB-item sets an IpAddress of a station that is connected to a port that performs RSP.
A value of 0.0.0.0 in this Mib Item means that it does not describe an existing IpAddress.
Default value is 0.0.0.0rw IpAddress .1.3.6.1.4.1.81.28.1.7.1.1.4 |
scEth OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.2 |
scEthPort OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.2.1 |
scEthPortTableTable of attributes which define configuration,
performance and error information about ethernet
ports based on the switchChip. SEQUENCE OF ScEthPortEntry .1.3.6.1.4.1.81.28.2.1.1 |
scEthPortEntryAn entry in the table, containing data about a single port. ScEthPortEntry .1.3.6.1.4.1.81.28.2.1.1.1 |
scEthPortGroupIdId of the group to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.28.2.1.1.1.1 |
scEthPortIdUnique Id of the port in the scEthPortTable.ro INTEGER .1.3.6.1.4.1.81.28.2.1.1.1.2 |
scEthPortOctetsRecThe total number of good octets received and bad octets
filtered by the port (excluding framing bits but including
FCS octets).
This item is the summation of scEthPortGoodOctetsRec
and scEthPortBadOctets.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.3 |
scEthPortPktsRecThe total number of good packets received and bad
packets filtered by the port.
This item is the summation of scEthPortGoodPktsRec
and scEthPortBadPkts.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.4 |
scEthPortGoodBroadcastPktsRecThe total number of good packets received that were
directed to the broadcast address.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.5 |
scEthPortGoodMulticastPktsRecThe total number of good packets received that were
directed to a multicast address.
Note that this number does not include packets directed to
the broadcast address.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.6 |
scEthPortCRCAlignErrorsThe total number of packets received that had a length
(excluding framing bits, but including FCS octets) of
between 64 and 1518 octets, inclusive, but were not an
integral number of octets in length or had a bad Frame
Check Sequence (FCS).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.7 |
scEthPortOversizePktsThe total number of packets received that were longer
than 1518 octets (excluding framing bits, but including
FCS octets) and were otherwise well formed.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.8 |
scEthPortFragmentsThe total number of packets received that were less than 64 octets in
length (excluding framing bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.9 |
scEthPortJabberThe total number of packets received that were longer
than 1518 octets (excluding framing bits, but including
FCS octets), and were not an integral number of octets in
length or had a bad Frame Check Sequence (FCS).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.10 |
scEthPortCollisionsThe best estimate of the total number of collisions on this
Ethernet segment.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.11 |
scEthPortPkts64OctetsThe total number of packets (including error packets)
that were 64 octets in length (excluding framing
bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.12 |
scEthPortPkts65to127OctetsThe total number of packets (including error packets)
that were between 65 and 127 octets in length
inclusive (excluding framing bits but including FCS
octets).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.13 |
scEthPortPkts128to255OctetsThe total number of packets (including error packets)
that were between 128 and 255 octets in length
inclusive (excluding framing bits but including FCS
octets).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.14 |
scEthPortPkts256to511OctetsThe total number of packets (including error packets)
that were between 256 and 511 octets in length
inclusive (excluding framing bits but including FCS
octets).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.15 |
scEthPortPkts512to1023OctetsThe total number of packets (including error packets)
that were between 512 and 1023 octets in length
inclusive (excluding framing bits but including FCS
octets).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.16 |
scEthPortPkts1024to1518OctetsThe total number of packets (including error packets)
that were between 1024 and 1518 octets in length
inclusive (excluding framing bits but including FCS
octets).ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.17 |
scEthPortGoodPktsRecThe total number of good packets received by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.18 |
scEthPortBadPktsThe total number of bad packets filtered by the port.
This item is the summation of:
scEthPortCRCAlignErrors, scEthPortOversizePkts,
scEthPortFragments and scEthPortJabber.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.19 |
scEthPortGoodOctetsRecThe total number of good octets of data received by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.20 |
scEthPortBadOctetsThe total number of bad octets of data filtered by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.21 |
scEthPortGoodBroadcastOctetsRecThe total number of good octets received that were
directed to the broadcast address.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.22 |
scEthPortGoodMulticastOctetsRecThe total number of good octets received that were
directed to a multicast address. Note that this number does
not include octets directed to the broadcast address.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.23 |
scEthPortGoodOctetsSentThe total number of good octets of data sent by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.24 |
scEthPortGoodPktsSentThe total number of good packets sent by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.25 |
scEthPortLateCollisionsThe best estimate of the total number of late collisions on
this Ethernet segment.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.26 |
scEthPortFunctionalStatusThe functional status of the port:
ok(1) - fully functional port, transmitting and receiving
packets.
rld(2) - receive link down condition on the port - Indicates
a cable or connector failure detected by the port H/W.
partition(8) - the port is in partition state.ro Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.27 |
scEthPortModeThe flow control mode of the port when operated in full duplex:
halfDuplex(1) - Half duplex connection, standard mode for segment
fullDuplexNoPause(2) - Full duplex connection without exchanging flow control packets
fullDuplexProprietaryFC(3) -
Full duplex connection with Lucent's proprietary flow control frames exchanged
fullDuplexISL(4) -
Full duplex connection with ISL proprietary protocol control words for
VLAN & priority exchanged, ISL = Inter-Switch-Link
fullDuplexFlowControlISL(5) -
Full duplex connection with both ISL proprietary protocol control words
and flow control frames exchanged
fullDuplexAsymTxPause(6) -
Full duplex connection with STD 802.3x flow control frames sent from this port,
but flow control packets received on it are not processed
fullDuplexSymPause(7) -
Full duplex connection with STD 802.3x flow control frames exchanged
fullDuplexAsymRxPause(8) -
Full duplex connection with no flow control frames sent from this port,
but STD 802.3x flow control 0frames received on it are processed.
For Giga ports, when auto-negotiation is enabled, the flow control mode is set
internally according to auto-negotiation resolution; and access to this item is read-only.rw Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.28 |
scEthPortSpeedThis parameter defines the port speed:
ethernet(1) and fastEthernet(2).rw Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.29 |
scEthPortAutoNegotiationThis object define if the Auto Sense /Auto Negotiation
process is enable(1) or disable (2)
for modules that don't support the Auto Snese mode
please define the notSupported option..rw Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.30 |
scEthPortAutoNegotiationStatusThis object define the status of the Auto Negotiation process:
pass: The Auto negotiation process was completed and succeeded .
fail: The Auto Negotiation process failed .
disable: The Auto Negotiation process is not enabled .
notSupported: The Auto Negotiation feature is not available in this module .ro Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.31 |
scEthPortTotalOctetsThe total number of octets received and transmitted on
the port (including all good and bad).
This item is the summation of scEthPortOctetsRec
and scEthPortGoodOctetsSent.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.32 |
scEthPortTotalPktsThe total number of packets received and transmitted on
the port (including all good and bad).
This item is the summation of scEthPortPktsRec
and scEthPortGoodPktsSent.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.33 |
scEthPortDropEventsThe total number of events in which the probe could not
count packets due to lack of resources. This number is not
necessarily the number of packets dropped; it is just the
number of times this condition has been detected.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.34 |
scEthPortGigaPauseStatusIndicates the status of the Flow Control as determined in the Auto Negotiation process on the
Gigabit ports:
noPause(1) indicates that there is no Flow Control.
symmetricPause(2) indicates that both sides are working in Tx&Rx Flow Control.
asymmetricPauseRx(3) indicates that both sides agreed on working in asynnetric Flow Control
- TxOnly against RxOnly.
If Giga Auto Neg is disabled, then noPause(1) is indicated when Flow Control is disabled,
while symmetricPause(2) is indicated when Flow Control is enabled.ro Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.35 |
scEthPortLower32OctetsRecLower 32 bit conter of the total number of octets of data received by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.36 |
scEthPortUpper32OctetsRecUpper 32 bit conter of the total number of octets of data received by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.37 |
scEthPortLower32OctetsSentLower 32 bit conter of the total number of octets of data sent by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.38 |
scEthPortUpper32OctetsSentUpper 32 bit conter of the total number of octets of data sent by the port.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.39 |
scEthPortGoodUnicastPktsRecThe total number of good packets received that were directed to a unicast address.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.40 |
scEthPortDiscardPktsRecThe total number of packets which were chosen to be discarded even
though no errors had been detected to prevent their being deliverable
to a higher-layer protocol. One possible reason for discarding such
a packet could be to free up buffer space.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.41 |
scEthPortUnicastPktsSentThe total number of good packets sent by the port
that were directed to a unicast address.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.42 |
scEthPortDiscardPktsSentThe total number of packets which were chosen to be discarded even though no errors
had been detected to prevent their being transmitted.
One possible reason for discarding such a packet could be to free up buffer space.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.43 |
scEthPortPauseCapabilitiesThe Pause capabilities of a Giga port that should be advertised to the link
partner when performing auto-negotiation:
noFlowControl (1) - no flow control support in any direction
asymTxFlowControlOnly (2) - STD 802.3x flow control frames can be sent from this port,
but flow control packets received on it can not be processed.
symFlowControlOnly (3) - STD 802.3x flow control frames must be supported in both directions
symAndAsymRxFlowControl (4) -
STD 802.3x flow control frames must be supported in both directions or
at least received flowcontrol frames on this port can be processed.rw Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.44 |
scEthPortMulticastPktsSentThe total number of good packets sent by the port that were directed to a multicast address.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.45 |
scEthPortUndersizePktsRecThe total number of packets received that were less than 64 octets long (excluding framing
bits, but including FCS octets) and were otherwise well formed.ro Counter .1.3.6.1.4.1.81.28.2.1.1.1.46 |
scEthPortFlowControlThe flow control mode of the portrw Enumeration .1.3.6.1.4.1.81.28.2.1.1.1.47 |
scEthGroup OBJECT IDENTIFIER .1.3.6.1.4.1.81.28.2.2 |
scEthGroupTableTable of attributes which define ethernet configuration
information about a single SC based group. SEQUENCE OF ScEthGroupEntry .1.3.6.1.4.1.81.28.2.2.1 |
scEthGroupEntryAn entry in the table, containing data about a single Group. ScEthGroupEntry .1.3.6.1.4.1.81.28.2.2.1.1 |
scEthGroupIdUnique Id of the group in the scEthGroupTable.
Equals the number of the slot by which the group is accessed.ro INTEGER .1.3.6.1.4.1.81.28.2.2.1.1.1 |
scEthGroupAutoPartitionEnableEnables/Disables the Auto-Partition mechanism in all ports of this module.rw Enumeration .1.3.6.1.4.1.81.28.2.2.1.1.2 |
scEthGroupFefiEnableThis item enables\disables the FEFI mechanism of all Fast-Ethernet
PHY's in the module. It enables\disables both the transmission and
the recognition of FEFI signals.rw Enumeration .1.3.6.1.4.1.81.28.2.2.1.1.3 |