CROUTE-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
144
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
144 total| Object Name |
|---|
croute OBJECT IDENTIFIER .1.3.6.1.4.1.81.31 |
RFC1155-SMI Unknown .1.3.6.1.4.1.81.31 |
ipRoute OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1 |
ipGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.1 |
ipGlobalsBOOTPRelayStatusWhenever to activate the BOOTP Relay protocol on the device.
enable - set by the user,
means activate the BOOTP Relay protocol over the defined VLANs.
disable - set by the user,
means don't active the BOOTP Relay protocol.
backup - set by the user,
means the BOOTP Relay protocol is in stand-by. It will enter to activeBackup mode
after IP REDUNDANCY mechanism will enter to active mode.
activeBackup - set by the device (status),
means the backup BOOTP Relay is working (after time-out of IP REDUNDANCY).rw Enumeration .1.3.6.1.4.1.81.31.1.1.1 |
ipGlobalsICMPErrMsgEnableWhenever to send ICMP messages such as Destination Unreachable, etc.rw Enumeration .1.3.6.1.4.1.81.31.1.1.2 |
ipGlobalsARPInactiveTimeoutTime-out required to remove inactive ARP entries. The value is in seconds.
The default value is 4 hoursrw INTEGER .1.3.6.1.4.1.81.31.1.1.3 |
ipInterfaceTableThis table is an extention of MIB II IpAddrTable, and is used to
add/delete entries to/from that table. In addition it contains private objects. SEQUENCE OF IpInterfaceEntry .1.3.6.1.4.1.81.31.1.2 |
ipInterfaceEntryThe information concerning one of this entity's IP interfaces.
An IP interface is a logical connection to a certain IP net/subnet. IpInterfaceEntry .1.3.6.1.4.1.81.31.1.2.1 |
ipInterfaceAddrThe IP address to which this entry's addressing information pertains.ro IpAddress .1.3.6.1.4.1.81.31.1.2.1.1 |
ipInterfaceNetMaskThe subnet mask associated with the IP address of this entry.
The value of the mask is an IP address with all the network bits
set to 1 and all the hosts bits set to 0.rw IpAddress .1.3.6.1.4.1.81.31.1.2.1.2 |
ipInterfaceLowerIfAliasThis object is an 'alias' name for the lower-layer interface on top
of which this IP interface is defined. The alias is specified
by the network manager, and provides a non-volatile 'handle'
for the lower-layer interface.
The semantics of the object are similar to the semantics of
the ifAlias object, defined by the Interfaces MIB. At the time
when this Madge MIB object was defined, the latest release
of the Interfaces MIB was draft-ietf-ifmib-mib-05.txt. The
purpose is to support all methods (static or dynamic) for creation
of interfaces and to allow creation of IP table entries without the need
of the layer 2 interface to be present on the device at the time of the
creation. It is assumed that some implementation dependent mechanisms
allow the IP application to be informed about the creation of new lower
layer interfaces.rw DisplayString .1.3.6.1.4.1.81.31.1.2.1.3 |
ipInterfaceTypeThe logical type of the interface. The default depends on the physical type.
For example Ethernet and Token-Ring LANs are of type broadcastrw Enumeration .1.3.6.1.4.1.81.31.1.2.1.4 |
ipInterfaceForwardIpBroadcastWhether the router forwards IP directed broadcasts that are to be
transmitted as link-layer broadcast to an attached net or subnet.rw Enumeration .1.3.6.1.4.1.81.31.1.2.1.5 |
ipInterfaceBroadcastAddrThe value of the least-significant bit in the IP broadcast address used
for sending datagrams on the (logical) interface associated with the IP
address of this entry.
For example, when the Internet standard all-ones broadcast address is
used, the value will be 1. This value applies to both the subnet and
network broadcasts addresses used by the entity on this (logical) interface.rw INTEGER .1.3.6.1.4.1.81.31.1.2.1.6 |
ipInterfaceProxyArpWhen proxy ARP is enabled, the router responds to ARP
requests received on one link-layer interface for an IP-address
that is reachable via another link-layer interface.
The response provides the router's own MAC address.rw Enumeration .1.3.6.1.4.1.81.31.1.2.1.7 |
ipInterfaceStatusFor adding and deleting IP interfaces. Deleting this row means
deleting the corresponding entry in IpAddrTable (MIB II). Deleting an
IP interface also causes deletion of all static routes defined on this IP
interface, as well as protocol interfaces (e.g. RIP and OSPF) defined on
this IP interface.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.1.2.1.8 |
ipInterfaceMainRouterAddrThe IP address of the main router backed up on this interface.rw IpAddress .1.3.6.1.4.1.81.31.1.2.1.9 |
ipInterfaceARPServerStatusWhenever to activate the ARP Server mechanism on this interface.
enable - set by the user,
means activate the ARP Server mechanism over this IP interface.
disable - set by the user,
means don't active the ARP Server mechanism over this IP interface.rw Enumeration .1.3.6.1.4.1.81.31.1.2.1.10 |
ipInterfaceNameThe name of this interface for compatibility with cli.rw DisplayString .1.3.6.1.4.1.81.31.1.2.1.11 |
ipInterfaceNetbiosRebroadcastinbound - netbios received from the interface are rebarodcasted,
outbound - netbios are rebraodcasted to this interface,
both - netbios are rebroadacsted both from and to this interface,
disable - netbios is not rebraodcasted neither from nor to this interface.
Currently only both and disable are supportedrw Enumeration .1.3.6.1.4.1.81.31.1.2.1.12 |
ipInterfaceIcmpRedirectsenable - enable the sending of redirect messages if the router is forced to
re-send a packet through the same interface on which it was received.
disable - disable the sending of redirect messages on this interface.rw Enumeration .1.3.6.1.4.1.81.31.1.2.1.13 |
ripGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.3 |
ripGlobalsRIPEnableWhenever to activate the RIP protocol on the device.
disable means don't activate RIP over all the IP interfaces
enable means that the status of each interface is relevantrw Enumeration .1.3.6.1.4.1.81.31.1.3.1 |
ripGlobalsLeakOSPFIntoRIPWhenever to leak (redistribute) routes learned from OSPF protocol into
the domain of the RIP protocol.rw Enumeration .1.3.6.1.4.1.81.31.1.3.2 |
ripGlobalsLeakStaticIntoRIPWhenever to leak (redistribute) routes learned from Static Route into
the domain of the RIP protocol.rw Enumeration .1.3.6.1.4.1.81.31.1.3.3 |
ripInterfaceTableThis table is an extention of rip2IfConfTable, and is used to add/delete
objects entries to/from that table. SEQUENCE OF RipInterfaceEntry .1.3.6.1.4.1.81.31.1.4 |
ripInterfaceEntryThe information concerning one of this entity's IP interfaces.
An IP interface is a logical connection to a certain IP net/subnet. RipInterfaceEntry .1.3.6.1.4.1.81.31.1.4.1 |
ripInterfaceAddrThe IP address to which this entry's addressing information pertains.ro IpAddress .1.3.6.1.4.1.81.31.1.4.1.1 |
ripInterfaceMetricThis variable indicates the number of hops that is to be assign
to that interface.rw INTEGER ( 0..15 ) .1.3.6.1.4.1.81.31.1.4.1.2 |
ripInterfaceSplitHorizonWhether to activate Poison Reverse algorithm,
Split Horizon or none of them, on this interfacerw Enumeration .1.3.6.1.4.1.81.31.1.4.1.3 |
ripInterfaceAcceptDefaultRouteWhether to accept the default route from receive RIP message.rw Enumeration .1.3.6.1.4.1.81.31.1.4.1.4 |
ripInterfaceSendDefaultRouteWhether to send the default route in RIP message.rw Enumeration .1.3.6.1.4.1.81.31.1.4.1.5 |
ripInterfaceStateThe operational (current state) of the IP interface from RIP point of view.
It depends on Global RIP status, IP interface status and rip interface STATUS.
inactive - set by the device (status), the rip is not active on this interface.
active - set by the device (status), rip is active on this interface.ro Enumeration .1.3.6.1.4.1.81.31.1.4.1.6 |
ripInterfaceSendModeWhat the router sends on this interface.
All - send the whole routing table according to the RIP version.
DefaultOnly - send default route only.
DoNotDend - don't send any RIP information on this interface.rw Enumeration .1.3.6.1.4.1.81.31.1.4.1.7 |
ripInterfaceVersionWhat RIP information the router sends on this interface.rw Enumeration .1.3.6.1.4.1.81.31.1.4.1.8 |
ospfGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.5 |
ospfGlobalsLeakRIPIntoOSPFWhenever to leak (redistribute) routes learned from RIP protocol into
the domain of the OSPF protocol.rw Enumeration .1.3.6.1.4.1.81.31.1.5.1 |
ospfGlobalsLeakStaticIntoOSPFWhenever to leak (redistribute) routes learned from Static Route into
the domain of the OSPF protocol.rw Enumeration .1.3.6.1.4.1.81.31.1.5.2 |
ospfGlobalsLeakDirectIntoOSPFWhenever to leak (redistribute) routes learned from Direct into
the domain of the OSPF protocol.rw Enumeration .1.3.6.1.4.1.81.31.1.5.3 |
relayTableThis table is an extention of vlConfTable, and is used to add/delete
DHCP Servers to/from that table. SEQUENCE OF RelayEntry .1.3.6.1.4.1.81.31.1.6 |
relayEntryThe information concerning one of this entity's VLAN interfaces.
An VLAN interface is a virtual connection to a switch. RelayEntry .1.3.6.1.4.1.81.31.1.6.1 |
relayVlIndexA unique value for each interface. Its value ranges between 1
and the value of ifNumber. The value for each interface must
remain constant at least from one re-initialization of the entity's
network management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.81.31.1.6.1.1 |
relayVlPrimaryServerAddrThe IP address of the primary server, to which the BOOTP/DHCP
requests to be sent.rw IpAddress .1.3.6.1.4.1.81.31.1.6.1.2 |
relayVlSeconderyServerAddrThe IP address of the secondary server, to which the BOOTP/DHCP
requests to be sent.rw IpAddress .1.3.6.1.4.1.81.31.1.6.1.3 |
relayVlStatusFor deleting an DHCP/BOOTP servers entry. The entry will be deleted upon
deleting the corresponding VLANrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.1.6.1.4 |
relayVlRelayAddrThe IP address of the Relay, i.e. the router's IP address to write in the relayed request
(giaddr field in the Bootp packet). When there are multiple IP interfaces on the same
VLAN such that the router has multiple IP addresses on the VLAN, the user can configure
which of these addresses to use when relaying requests arriving on this VLAN.
This relay address is used by the server to determines the subnet from which the address
shall be allocated. The special value 255.255.255.255 means DUPLICATE.
In this case the Relay will duplicate each request arriving on this VLAN and send to
the server multiple copies of the request, a copy for each of the router's IP addresses
on that VLAN. The relay address in each copy of the request shall be the router's
IP address (NOT 255.255.255.255). The special value 0.0.0.0 means that the router shall
use the Default value (lowest IP address on the VLAN) for the relay addressrw IpAddress .1.3.6.1.4.1.81.31.1.6.1.5 |
ipAccessGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.7 |
ipAccessControlEnableWhenever to activate the IP ACCESS CONTROL statements on the device.
disable means don't activate IP ACCESS CONTROL over all the IP statements
enable means activate IP ACCESS CONTROL over all the IP statementsrw Enumeration .1.3.6.1.4.1.81.31.1.7.1 |
ipAccessControlTableThis table is used to add/delete access control statement
to/from that table. SEQUENCE OF IpAccessControlEntry .1.3.6.1.4.1.81.31.1.8 |
ipAccessControlEntryThe information concerning one of this entity's IP interfaces.
An IP interface is a logical connection to a certain IP net/subnet. IpAccessControlEntry .1.3.6.1.4.1.81.31.1.8.1 |
ipAccessControlIndexEntry index.ro INTEGER .1.3.6.1.4.1.81.31.1.8.1.1 |
ipAccessControlSrcAddrThe IP address of the source address.rw IpAddress .1.3.6.1.4.1.81.31.1.8.1.2 |
ipAccessControlSrcMaskThe MASK address of the source address.rw IpAddress .1.3.6.1.4.1.81.31.1.8.1.3 |
ipAccessControlDstAddrThe IP address of the destination address.rw IpAddress .1.3.6.1.4.1.81.31.1.8.1.4 |
ipAccessControlDstMaskThe MASK address of the destination address.rw IpAddress .1.3.6.1.4.1.81.31.1.8.1.5 |
ipAccessControlOperationHow to operate the IP ACCESS CONTROL statement, on the receiving packet.
Forwards the packet, Block (Discard) the packet or block (Discard) the packet
and report to the user by sending trap.rw Enumeration .1.3.6.1.4.1.81.31.1.8.1.6 |
ipAccessControlActivationDoes the IP ACCESS CONTROL statement done by HW or SW(CPU).
HW - wire-speed, SW - regular.rw Enumeration .1.3.6.1.4.1.81.31.1.8.1.7 |
ipAccessControlProtocolOver which protocol does the IP ACCESS CONTROL statement activate.
Icmp, Tcp, Udp. None - means IP addresses onlyrw Enumeration .1.3.6.1.4.1.81.31.1.8.1.8 |
ipAccessControlApplicationOver which application does the IP ACCESS CONTROL statement activate.
The exception are: above1023 can work over TCP or UDP, none can't work
over TCP or UDP or ICMP only none is exceptedrw Enumeration .1.3.6.1.4.1.81.31.1.8.1.9 |
ipAccessControlStatusFor create/delete of a IP ACCESS CONTROL statement.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.1.8.1.10 |
ipRedundancyGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.9 |
ipRedundancyStatusWhenever to activate the IP REDUNDANCY mechanism on the device.
enable - set by the user,
means activate the IP REDUNDANCY mechanism over the defined IP interfaces.
disable - set by the user,
means don't active the IP REDUNDANCY mechanism over the defined IP interfaces.
inactive - set by the device (status),
means the backup interface is in stand-by (after enable operation).
active - set by the device (status),
means the backup interface is working (after time-out).rw Enumeration .1.3.6.1.4.1.81.31.1.9.1 |
ipRedundancyTimeoutTime-out required to activate the backup process of IP REDUNDANCY. After Time-out
the Redundant router assumes that the main (Backuped) router is not operational, and takes
control over all defined IP interfaces of the main.
The value is in seconds.
The default value is 12rw INTEGER .1.3.6.1.4.1.81.31.1.9.2 |
ipRedundancyPollingIntervalThe polling interval used to poll the Main (Backed up) router.
The value is multiply of ipRedundancyTimeout.
The value is in seconds.
The default value is 3rw INTEGER .1.3.6.1.4.1.81.31.1.9.3 |
ipShortcutGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.10 |
ipShortcutARPServerStatusWhenever to activate the ARP Server mechanism on the device.
enable - set by the user,
means activate the ARP Server mechanism over the defined IP interfaces.
disable - set by the user,
means don't active the ARP Server mechanism over the defined IP interfaces.rw Enumeration .1.3.6.1.4.1.81.31.1.10.1 |
ipMulticastInterfaceTableThis table is used to update multicast parameters
over interfaces already define SEQUENCE OF IpMulticastInterfaceEntry .1.3.6.1.4.1.81.31.1.11 |
ipMulticastInterfaceEntryThe information concerning one of this entity's interfaces. IpMulticastInterfaceEntry .1.3.6.1.4.1.81.31.1.11.1 |
ipMulticastInterfaceIfIndexA unique value for each interface. Its value ranges between 1
and the value of ifNumber. The value for each interface must
remain constant at least from one re-initialization of the entity's
network management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.81.31.1.11.1.1 |
ipMulticastInterfaceSendAllThe user will be able to configure whenever to send the all Multicast
packets to this interface.
Enable - Enable the user to define this interface, over all the existing groups
Disable - Will acts according to the other parameters.rw Enumeration .1.3.6.1.4.1.81.31.1.11.1.2 |
ipMulticastInterfaceStateThe current state (operational) of the IP Multicast from IP Multicast point of view.
It depends on global ipMRouteEnable status and Multicast interface status.
Inactive - set by the device (status),
Global IP multicast is disabled or Multicast is disable on this interface.
Active - set by the device (status),
Global IP multicast is enable and Multicast is active on this interface.ro Enumeration .1.3.6.1.4.1.81.31.1.11.1.3 |
ipMulticastInterfaceStatusFor enable/disable of a IP multicast over an interface.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.1.11.1.4 |
ipEZ2RouteMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.13 |
ipEZ2BoostRouterTable SEQUENCE OF IpEZ2BoostRouterEntry .1.3.6.1.4.1.81.31.1.13.1 |
ipEZ2BoostRouterEntry IpEZ2BoostRouterEntry .1.3.6.1.4.1.81.31.1.13.1.1 |
ipEZ2BoostRouterSlotro INTEGER .1.3.6.1.4.1.81.31.1.13.1.1.1 |
ipEZ2BoostRouterBRAddressro IpAddress .1.3.6.1.4.1.81.31.1.13.1.1.2 |
ipEZ2BoostRouterTypero Enumeration .1.3.6.1.4.1.81.31.1.13.1.1.3 |
ipEZ2BoostRouterStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.1.13.1.1.4 |
ipEZ2RControlTable SEQUENCE OF IpEZ2RControlEntry .1.3.6.1.4.1.81.31.1.13.2 |
ipEZ2RControlEntry IpEZ2RControlEntry .1.3.6.1.4.1.81.31.1.13.2.1 |
ipEZ2RControlSlotro INTEGER .1.3.6.1.4.1.81.31.1.13.2.1.1 |
ipEZ2RControlBoostedRoutersTimeoutSet the timeout of EZ2route routersrw INTEGER .1.3.6.1.4.1.81.31.1.13.2.1.2 |
ipEZ2RControlHostsTimeoutSet the timeout of EZ2route hostsrw INTEGER .1.3.6.1.4.1.81.31.1.13.2.1.3 |
ipEZ2RControlAutoLearnModerw Enumeration .1.3.6.1.4.1.81.31.1.13.2.1.5 |
ipVRRP OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.1.14 |
ipVRRPAdminStatusGlobal switch to enable/disable VRRPrw Enumeration .1.3.6.1.4.1.81.31.1.14.1 |
ipxRoute OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.2 |
ipxCircTableThis table is an extention of Novell mib IpxCircTable, and is used to
add/delete entries to/from that table. In addition it contains private objects. SEQUENCE OF IpxCircEntry .1.3.6.1.4.1.81.31.2.1 |
ipxCircEntryThe information concerning one of this entity's IPX circuits.
An IPX circuit is a logical connection to a certain IPX netNumber. IpxCircEntry .1.3.6.1.4.1.81.31.2.1.1 |
ipxCircIndexThe identifier of this circuit, unique within the instance of IPX.
This value may be written only when creating a new entry in the table.ro INTEGER .1.3.6.1.4.1.81.31.2.1.1.1 |
ipxCircNetNumberThe IPX network number of this circuit.rw NetNum .1.3.6.1.4.1.81.31.2.1.1.2 |
ipxCircLowerIfAliasThis object is an 'alias' name for the lower-layer interface on top
of which this IP interface is defined. The alias is specified
by the network manager, and provides a non-volatile 'handle'
for the lower-layer interface.
The semantics of the object are similar to the semantics of
the ifAlias object, defined by the Interfaces MIB. At the time
when this Madge MIB object was defined, the latest release
of the Interfaces MIB was draft-ietf-ifmib-mib-05.txt. The
purpose is to support all methods (static or dynamic) for creation
of interfaces and to allow creation of IPX table entries without the need
of the layer 2 interface to be present on the device at the time of the
creation. It is assumed that some implementation dependent mechanisms
allow the IPX application to be informed about the creation of new lower
layer interfaces.rw DisplayString .1.3.6.1.4.1.81.31.2.1.1.3 |
ipxCircEncapsulationThe media type (encapsulation of layer2) of this circuit.rw Enumeration .1.3.6.1.4.1.81.31.2.1.1.4 |
ipxCircNetbiosThe type of the circuit.rw Enumeration .1.3.6.1.4.1.81.31.2.1.1.5 |
ipxCircStatusFor adding and deleting Circuits. Deleting this row means deleting
the corresponding entry in ipxCircTable. Deleting a Circuit also
causes deletion of all static routes defined on this Circuit,
as well as protocol Circuit (e.g. RIP and SAP) defined on this Circuit.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.2.1.1.6 |
ipxCircRipUpdateThe RIP periodic update interval, in seconds.rw INTEGER .1.3.6.1.4.1.81.31.2.1.1.7 |
ipxCircRipAgeMultiplierThe holding multiplier for information received in RIP periodic updates.rw INTEGER .1.3.6.1.4.1.81.31.2.1.1.8 |
ipxCircRipStatusIndicates whether RIP information may be sent/received over this circuit.
Set by the userrw Enumeration .1.3.6.1.4.1.81.31.2.1.1.9 |
ipxCircSapUpdateThe SAP periodic update interval, in seconds.rw INTEGER .1.3.6.1.4.1.81.31.2.1.1.10 |
ipxCircSapAgeMultiplierThe holding multiplier for information received in SAP periodic updates.rw INTEGER .1.3.6.1.4.1.81.31.2.1.1.11 |
ipxCircGetNearestServerReplyIndicates whether to respond to SAP get nearest server requests
received on this circuit.rw Enumeration .1.3.6.1.4.1.81.31.2.1.1.12 |
ipxCircSapStatusIndicates whether SAP information may be sent/received over this circuit.rw Enumeration .1.3.6.1.4.1.81.31.2.1.1.13 |
ipxCircRipStateIndicates whether RIP information may be sent/received over this circuit.
Set by the device to reflect the RIP status and the interface statusro Enumeration .1.3.6.1.4.1.81.31.2.1.1.14 |
ipxCircSapStateIndicates whether SAP information may be sent/received over this circuit.
Set by the device to reflect the SAP status and the interface statusro Enumeration .1.3.6.1.4.1.81.31.2.1.1.15 |
ipxDestTableThis table replace the Novell mib IpxDestTable, and is used to
add/delete entries to/from that table. SEQUENCE OF IpxDestEntry .1.3.6.1.4.1.81.31.2.2 |
ipxDestEntryThe information concerning one of this entity's IPX Routes.
An IPX service is a logical connection to a certain IPX Server. IpxDestEntry .1.3.6.1.4.1.81.31.2.2.1 |
ipxDestNetNumThe IPX network number portion of the IPX address of the destination.ro NetNum .1.3.6.1.4.1.81.31.2.2.1.1 |
ipxDestProtocolThe routing protocol from which knowledge of this destination was obtained.ro Enumeration .1.3.6.1.4.1.81.31.2.2.1.2 |
ipxDestTicksThe delay in ticks to reach this destination.rw INTEGER .1.3.6.1.4.1.81.31.2.2.1.3 |
ipxDestHopCountThe number of hops necessary to reach the destination.rw INTEGER .1.3.6.1.4.1.81.31.2.2.1.4 |
ipxDestNextHopCircIndexThe unique identifier of the circuit, used to reach the next hop.rw INTEGER .1.3.6.1.4.1.81.31.2.2.1.5 |
ipxDestNextHopNICAddressThe NIC address of the next hop.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.81.31.2.2.1.6 |
ipxDestNextHopNetNumThe IPX network number of the next hop.rw NetNum .1.3.6.1.4.1.81.31.2.2.1.7 |
ipxDestStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.2.2.1.8 |
ipxDestAgeThe age of the Routing table entry.ro INTEGER .1.3.6.1.4.1.81.31.2.2.1.9 |
ipxServTableThis table replace the Novell mib IpxServTable, and is used to
add/delete entries to/from that table. SEQUENCE OF IpxServEntry .1.3.6.1.4.1.81.31.2.3 |
ipxServEntryThe information concerning one of this entity's IPX Services.
An IPX service is a logical connection to a certain IPX Server. IpxServEntry .1.3.6.1.4.1.81.31.2.3.1 |
ipxServTypeThe service type.ro INTEGER .1.3.6.1.4.1.81.31.2.3.1.1 |
ipxServNameThe server name.ro DisplayString .1.3.6.1.4.1.81.31.2.3.1.2 |
ipxServProtocolThe protocol from which knowledge of this service was obtained.ro Enumeration .1.3.6.1.4.1.81.31.2.3.1.3 |
ipxServNetNumThe IPX network number portion of the IPX address of the service.rw NetNum .1.3.6.1.4.1.81.31.2.3.1.4 |
ipxServNodeThe node portion of the IPX address of the service.rw OCTET STRING .1.3.6.1.4.1.81.31.2.3.1.5 |
ipxServSocketThe socket portion of the IPX address of the service.rw INTEGER .1.3.6.1.4.1.81.31.2.3.1.6 |
ipxServHopCountThe number of hops to the service.rw INTEGER .1.3.6.1.4.1.81.31.2.3.1.7 |
ipxServStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.2.3.1.8 |
ipxServAgeThe age of the SAP entry.ro INTEGER .1.3.6.1.4.1.81.31.2.3.1.9 |
ipxAccessGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.2.4 |
ipxAccessControlEnableWhenever to activate the IPX ACCESS CONTROL statements on the device.
disable means don't activate IPX ACCESS CONTROL over all the IPX statements
enable means activate IPX ACCESS CONTROL over all the IPX statementsrw Enumeration .1.3.6.1.4.1.81.31.2.4.1 |
ipxAccessControlTableThis table is used to add/delete IPX access control statement
to/from that table. SEQUENCE OF IpxAccessControlEntry .1.3.6.1.4.1.81.31.2.5 |
ipxAccessControlEntryThe information concerning one of this entity's IPX access control statements. IpxAccessControlEntry .1.3.6.1.4.1.81.31.2.5.1 |
ipxAccessControlIndexEntry index.ro INTEGER .1.3.6.1.4.1.81.31.2.5.1.1 |
ipxAccessControlSrcAddrThe IPX network of the source address.rw NetNum .1.3.6.1.4.1.81.31.2.5.1.2 |
ipxAccessControlDstAddrThe IPX network of the destination address.rw NetNum .1.3.6.1.4.1.81.31.2.5.1.3 |
ipxAccessControlOperationHow to operate the IPX ACCESS CONTROL statement, on the receiving packet.
Forwards the packet, Block (Discard) the packet or block (Discard) the packet
and report to the user by sending trap.rw Enumeration .1.3.6.1.4.1.81.31.2.5.1.4 |
ipxAccessControlActivationDoes the IPX ACCESS CONTROL statement done by HW or SW(CPU).
HW - wire-speed, SW - regular.rw Enumeration .1.3.6.1.4.1.81.31.2.5.1.5 |
ipxAccessControlStatusFor create/delete of an IPX ACCESS CONTROL statement.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.81.31.2.5.1.6 |
ipxSapFilterGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.81.31.2.6 |
ipxSapFilterEnableWhenever to activate the IPX SAP Filters statements on the device.
disable means don't activate IPX SAP Filters over all the IPX SAP statements
enable means activate IPX SAP Filter over all the IPX SAP statementsrw Enumeration .1.3.6.1.4.1.81.31.2.6.1 |
ipxSapFilterTableTable of input/output SAP filter according to IPX circuit number. SEQUENCE OF IpxSapFilterEntry .1.3.6.1.4.1.81.31.2.7 |
ipxSapFilterEntryAn entry in the SAP filter table IpxSapFilterEntry .1.3.6.1.4.1.81.31.2.7.1 |
ipxSapFilterIDID of SAP filter.ro INTEGER .1.3.6.1.4.1.81.31.2.7.1.1 |
ipxSapFilterCircIndex....
::= {ipxSapFilterEntry 2}
ipxSapFilterServiceNetNumber OBJECT-TYPE
SYNTAX NetNum
ACCESS read-write
STATUS mandatory
DESCRIPTIONrw INTEGER .drStaticCidrEntry.14 |