APPLIC-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for APPLIC-MIB.
353
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
353 total| Object Name |
|---|
lntLanSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.81.19 |
RFC1155-SMI Unknown .1.3.6.1.4.1.81.19 |
lse OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.1 |
lseGroupTable SEQUENCE OF LseGroupEntry .1.3.6.1.4.1.81.19.1.1 |
lseGroupEntry LseGroupEntry .1.3.6.1.4.1.81.19.1.1.1 |
lseGroupIdSlot number in which the group is installed.ro INTEGER .1.3.6.1.4.1.81.19.1.1.1.1 |
lseGroupFastOpenSetting the value of this attribute to ON activates the port for short idle time
when code violation was detected.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.2 |
lseGroup10MSqltSetting the value of this attribute to ON activates the mechanism of detection
preamble of 10Mhz.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.3 |
lseGroupSmartSqltControl the mechnism of the input sensitivity of the port.rwdeprecated Enumeration .1.3.6.1.4.1.81.19.1.1.1.4 |
lseGroupCParameterDefines the number of consecutive collisions the port waits before it ceases transmitting
of 512 bits time toward the station.rw INTEGER .1.3.6.1.4.1.81.19.1.1.1.5 |
lseGroupIPGJamLengthDefines the IPG jam length in Ethernet bit time (100nS) start at 16 bit time in
steps of 16, to 112 bit time.
For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bit times (480nano-seconds)
in step of 4, to 124 (1240nano-seconds).
Any number between the defined values will take to nearest smaller value.rw INTEGER .1.3.6.1.4.1.81.19.1.1.1.6 |
lseGroupJamLengthDefines the Jam Length in time starting from 8 (800micro-seconds) to
120 (12mili-seconds). Each step of 8 is equal 800micro-seconds.
For LFE-100, values are from 8 (80micro-seconds) to 32 (320micro-seconds),
each step of 8 is equal 800micro-seconds.
Any number between the defined values will take to nearest smaller value.rw INTEGER .1.3.6.1.4.1.81.19.1.1.1.7 |
lseGroupDataBlinderLengthDefines the Data Blinder Length in Ethernet bit time (100nS) start at 16 bit time in steps of
16 to 112 bit time.
For LFE-100, (Fast Ethernet bit time (10nS)) values are from 0 bit times
in step of 4, to 124 (1240nano-seconds).
Any number between the defined values will take to nearest smaller value.rw INTEGER .1.3.6.1.4.1.81.19.1.1.1.8 |
lseGroupIPGDataLengthDefines the IPG (Inter Packet Gap) length in Ethernet bit time
(100nS) starting at 16 bit time in steps of 16 to 112 bit time.
For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bit times
(480nano-seconds) in step of 4, to 124 (1240 nano-seconds).
Any number between the defined values will take to nearest smaller value.rw INTEGER .1.3.6.1.4.1.81.19.1.1.1.9 |
lseGroupActiveMonitorThis attribute defines the module which is the high-speed bus active monitor.ro Enumeration .1.3.6.1.4.1.81.19.1.1.1.10 |
lseGroupBackbone12Port 1 and 2 in the board perform as Backbone link.
lse208 - upper cluster is RX only and lower cluster is TX only.
lse404 - upper port is Rx only and second port is Tx only. Two remains port are performed as regular foirl interfaces.
lse808 - the first port is RX from line only, the second - TX to line only, the rest are in regular10BaseT mode.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.11 |
lseGroupSetDefaultsSet all hardware parameters to their default values. This item will
always return a value of off(2), since it acts like a toggle switch.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.12 |
lseGroupBackbone34Port 3 and 4 in the board performed as Backbone link.
lse404 - Third port is Rx only and forth port is Tx only.
Two remaining ports performed as regular foirl interfaces.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.13 |
lseGroupBackboneRedun12Value on(1) of this attribute defines a redundancy (backup)
relationship between Backbone port 1 and backbone port 2
on a LANswiltch module.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.14 |
lseGroupBackoffFromJamValue on(1) of this attribute defines non-consecutive
jam after a collision has occured in LANswitch modules.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.15 |
lseGroupCAMClearValue on(1) of this attribute causes the LANSwitch
module to clear the CAM tables.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.16 |
lseGroupJamPreventJam prevent flag.
Functionaly, Jam prevent is a back-pressure into the line direction.
There are two modes of opration:
1) automatic - the sensor gets the items status from HW
2) manual - the sensor gets the items status from user.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.17 |
lseGroupNormOpClNormaly Open/Close flag.
When open(1) state is set, the sensor should activate
a delay mechanism for the module to operate at Normaly-Closed
mode for 30 seconds in order to enable the port's CAM to learn the
current segmentationrw Enumeration .1.3.6.1.4.1.81.19.1.1.1.18 |
lseGroupNormOpDelayWhen sets to a value greater than 0 (zero) and the MIB item
lseGroupNormOpCl is equal to closed(2), this item define the time
delay that the module will remain in normally open mode before
it will move to normaly close mode. This will be activated after
the user will reset the module.
The value is in seconds.rw INTEGER .1.3.6.1.4.1.81.19.1.1.1.19 |
lseGroupAutoPartitionEnableEnables autopartition mechanism support in the group level for each port of the group.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.20 |
lseGroupWorkStateOne of the possible states of the module: this item
indicates if the module is runing or booting. The value
runAndBoot(3) indicates a serious software problem.ro Enumeration .1.3.6.1.4.1.81.19.1.1.1.21 |
lseGroupBITResultThe Bit Indication Test in state 'faulty' indicates a problem.
The agent should send a fault trap in this case.ro Enumeration .1.3.6.1.4.1.81.19.1.1.1.22 |
lseGroupAssignSlotsIn a multi-backbone configuration within a single HUB, this item enables to assign
backbone module with specific slot numbers. Only packets from these slots should be
handled by the backbone module, Packets from other slots are ignored.
The 16-bit string represents the slots in the hub, a Bit per slot. Bit 0 (LSB) corresponds
to slot 1, Bit 15 (MSB) corresponds to slot 16.
A Bit set to '1' indicates that the corresponding slot is assigned to this backbone module.
A clear Bit '0', indicates that the corresponding slot is ignored by this module.
Todate, only the LEB200 module supports this capability.
The string is expressed in Hex.
Default value is FF, i.e., all slots are assigned to module.rw OCTET STRING ( SIZE (2)) .1.3.6.1.4.1.81.19.1.1.1.23 |
lseGroupHSBMonStatusThis is a bit-masked attribute which displays events which may cause HSB Reset.
When a bit is '1', the relevant evet may cause HSB Reset.
When a bit is '0', the relevant evet will not cause HSB Reset.
The following are the events:
LSB D0 - Too many packets were discarded from a queue.
D1 - One of the Tx buffers to HSB is full for more than a default period.
D2 - Token has not been available for more than a default period.
D3 - RX Buffer full in one of the ports.
D4 -'1' HSB Reset has been occured , '0'- HSB reset hadn't occured since last
time this MIB has been read.
D5 - '0' - the ram of the relevant port is O.K. (the port is decode in D6-D7) , '1'
The ram is not O.K.
D6- D7 Decode the relevant port that It's ram is not O.K
00 - Port no'0
01 - Port no' 1
10 - Port no' 2
11 - Port no' 3.ro INTEGER .1.3.6.1.4.1.81.19.1.1.1.24 |
lseGroupEnableHSBResetThis item enables/disables the HSB Reset mechanism in the module.rw Enumeration .1.3.6.1.4.1.81.19.1.1.1.25 |
lseIntPort OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.1.2 |
lseIntPortTable SEQUENCE OF LseIntPortEntry .1.3.6.1.4.1.81.19.1.2.1 |
lseIntPortEntryAn entry in the table, containing data about a single internal LanSwitch bank. LseIntPortEntry .1.3.6.1.4.1.81.19.1.2.1.1 |
lseIntPortGroupIdId of the group to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.1 |
lseIntPortIdNumber of LanSwitch port in the board.ro INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.2 |
lseIntPortIOModeon(1) activates IO mode in which all packets on the
high-speed bus that were not captured by any regular
port are captured by the I/O port.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.3 |
lseIntPortResetSwitchCAMActing like toggle switch thus always returns off(2)
on read. When set to on(1), causes the reset of the
LANswitch CAM (addresses) memory.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.4 |
lseIntPortVideoPacketWhen set to on(1), all Tx packets toward the
high-speed bus to video type packets.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.5 |
lseIntPortPriorityStateMachineSetting the value of this attribute to on(1) activates
the priority mechanism.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.6 |
lseIntPortActiveBroadcastPrioritySetting the value of this attribute to on(1) activates
the active broadcast mode in priority mechanism.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.7 |
lseIntPortPriorityLevelThis attribute defines the priority levels of
Tx packets toward the high-speed bus.
The highest priority is broadcast(1).rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.8 |
lseIntPortSuperPriorityEnableWhen limited space is left in Tx buffer, only the highest priority
packets are accepted. This in turn can create a situation in which one
port tries to send a packet and never gets its chance to be accepted. In
order to prevent it the destination port counts the successive number
of tries of the low priority port, and when a certain (8) number is
reached, it accepts the packet anyhow.
The value on(1) defines the retry parameter for the priority level mechanism.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.9 |
lseIntPortRoutingModegeneric(1) - examines all the packets that are
not members of any virtual network.
net(2) - examines only the packets that have
the port's network number.
allPackets(4) - examine all packets regardless
of their routing mode.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.10 |
lseIntPortGlobalSetting the global mode to on(1) sets the
port in a network routing mode that examines
all packets that are not members of all virtual networks.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.11 |
lseIntPortLearnIOCAMSetting this parameter to on(1) enables an I/O port to
learn incoming MAC addresses received in its port and
store them in its CAM. Packets with destination address
that match the CAM addresses are not transferred to the high speed bus.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.12 |
lseIntPortSecuritySetting the value of this attribute to on(1) activates the security mode.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.13 |
lseIntPortIgnoreBusySetting the value of this attribute to on(1) activates the ignore busy mode.
The busy signal toward the high-speed bus is not activated even though the TX buffer is full.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.14 |
lseIntPortRetryPriorityLevel1The port increases the priority level of the high-speed bus packets after the defined number
(0..31) trials.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.15 |
lseIntPortRetryPriorityLevel2The port increases the priority level of the high-speed bus packets after the defined number
(0..255) trials.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.16 |
lseIntPortRetryPriorityLevel3The port increases the priority level of the high-speed bus packets after the defined number
(0..255) trials.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.17 |
lseIntPortIgnoreProtocolTypeAny packet regardless of the protocol type is received from the high-speed bus.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.18 |
lseIntPortCompanyMACThe attribute defines the first three bytes of the MAC address of the video host server.rw OCTET STRING .1.3.6.1.4.1.81.19.1.2.1.1.19 |
lseIntPortTxSafetyZoneDefines the Tx Safety Zone in bits.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.20 |
lseIntPortRxSafetyZoneDefines the Rx Safety Zone in bits.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.21 |
lseIntPortTxBurstLengthDefines the TX Burst Length in bits.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.22 |
lseIntPortSecurityIntruderThe value on(1) of this attribute reflects a security violation occurrence.ro Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.23 |
lseIntPortJabberValue on(1) of this attribute reflects that jabber was transmitted
to the port by the high-speed bus.ro Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.24 |
lseIntPortCAM112 bytes of MAC addresses. Each contains one
byte of the port number and six bytes of the MAC
address. This enables to send 16 MAC Addresses
( 16*7=112 bytes)rw OCTET STRING ( SIZE .1.3.6.1.4.1.81.19.1.2.1.1.25 |
lseIntPortVideoStateMachineSetting the value of this attribute to on(1) activates the video state machine mode.
Received packets are filtered by demand from the station.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.26 |
lseIntPortTransmitWeightDefines the Transmit Weight of the frames for the current LANswitch port toward
the high - speed bus.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.27 |
lseIntPortSuperPrioritySetting the value of this attribute to on(1) activates the retry priority functions.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.28 |
lseIntPortAlignmentThe number of alignment errors observed on a specified port.ro Counter .1.3.6.1.4.1.81.19.1.2.1.1.29 |
lseIntPortRxRejectThe number of Rx buffer full observed on a specified port, from the line toward the
High-speed bus.roobsolete Counter .1.3.6.1.4.1.81.19.1.2.1.1.30 |
lseIntPortTxRejectThe number of Tx buffer full observed on a specified port, from the line toward the
High-speed bus.roobsolete Counter .1.3.6.1.4.1.81.19.1.2.1.1.31 |
lseIntPortRxEmpty0Define the highest threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is full.
When the buffer reached this threshold, all packets will be rejected.
Version 7.0rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.32 |
lseIntPortRxEmpty1Define the middle threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is almost full.
When the buffer reached this threshold, the only packets that the port
will receive will be those with the highest priority (1) who were already
written in the priority machine. All other packets will be rejected.
The space between empty1 to empty0 is reserved to packets with
the highest priority (1) who were already written in the priority machine.
Version 7.0rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.33 |
lseIntPortRxEmpty2Define the lowest threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is almost full.
When the buffer reached this threshold, the only packets that the port
will receive will be those with at least middle priority (2) who were
already written in the priority machine. All other packets will be rejected.
The space between empty2 to empty1 is reserved to packets with at least
middle priority (2) who were already written in the priority machine.
When the buffer did not reached this lowest priority, no packet will be
rejected for empty space. Version 7.0rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.34 |
lseIntPortSuperNetNumberIf the internal port supports SuperNet mode, the user
have to define the supernet number. Default value is 0.
Change of this number when the internal port is Generic,
Global or Global SuperNet must be blocked by the sensor.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.35 |
lseIntPortGlobalSuperNetAn internal port that is part of all SuperNets is set to
Global SuperNet routing. The SuperNet number is 15
in this case.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.36 |
lseIntPortMACAddressThe MAC address of the port, if it has. If not, an octet
string of length 0.ro OCTET STRING .1.3.6.1.4.1.81.19.1.2.1.1.37 |
lseIntPortIgnoreRoutingModeWhen this parameter is 'ignore', the LANSwitch
port monitors all packets without paying attention
to the virtual net assignment.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.38 |
lseIntPortCAMLastChangeThis attribute contains the value of sysUpTime
at the time any change occured to the
content of the specific CAM.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.19.1.2.1.1.39 |
lseIntPortCopiedPortThe port monitored on the LANswitch bus by the
LSE-PM module. The value of this item is: 32*(S-1)+P,
where S is the slot number in the hub and P the port
within the slot (1.. 32).
When the value of this item is 0, the Copy Port function
is disabled and the port is in Host Filter mode. For
modules that do not support this functionality, this
item will have the value 65,535.rw INTEGER .1.3.6.1.4.1.81.19.1.2.1.1.40 |
lseIntPortBroadcastBehaviorThis item relates only to LSE-PM modules. The value of
this item defines the method by which the module treats
broadcast and multicast packets.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.41 |
lseIntPortFilteringMethodThis item is relevant only to the LSE-PM module.
The value of this item defines the filtering method
used to capture packets from the Cellenium bus to
the Ethernet connection.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.42 |
lseIntPortSetFilterThis item is relevant only to the LSE-PM module.
The item is used to add new addresses to the module's
filtering table. The string is a sequence of MAC addresses,
6 bytes each. When the item is set, each address in the list
is added to the filtering table, and related packets are then
captured.
This item always returns an empty string in response to
get requests.rw OCTET STRING ( SIZE .1.3.6.1.4.1.81.19.1.2.1.1.43 |
lseIntPortRemoveFilterThis item is relevant only to the LSE-PM module.
The item is used to remove existing addresses from
the module's filtering table. The string is a sequence of
MAC addresses, 6 bytes each. When the item is set, all
addresses in the list are removed from the filtering table,
and the module stops capturing related packets .rw OCTET STRING ( SIZE .1.3.6.1.4.1.81.19.1.2.1.1.44 |
lseIntPortClearFilterThis item is relevant only to the LSE-PM module.
The item acts as a toggle switch: when its value is set
to clear(2), the contents of the module's filtering
tables are cleared.
This item always returns an empty string in response to
get requests.rw Enumeration .1.3.6.1.4.1.81.19.1.2.1.1.45 |
lseIntPortMonitorMissedEventsThis item is relevant only to LSE-PM modules. The value
of the counter is the number of packets that were not
captured by the port as a result of overload on the
Ethernet line, though the port's filter was configured
to capture these packets.ro Counter .1.3.6.1.4.1.81.19.1.2.1.1.46 |
lseIntPortMACAdd OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.1.2.2 |
lseIntPortMACAddTable SEQUENCE OF LseIntPortMACAddEntry .1.3.6.1.4.1.81.19.1.2.2.1 |
lseIntPortMACAddEntryAn entry in the table containing data about a single internal switch port. LseIntPortMACAddEntry .1.3.6.1.4.1.81.19.1.2.2.1.1 |
lseIntPortMACAddGroupIdId of the group to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.19.1.2.2.1.1.1 |
lseIntPortMACAddPortIdThe LANswitch port number in the board.ro INTEGER .1.3.6.1.4.1.81.19.1.2.2.1.1.2 |
lseIntPortMACAddLAIdThe lower 2 bytes of the Last MAC Address on the previous
list. Use the 0 value to start from the beginning of the list.ro INTEGER .1.3.6.1.4.1.81.19.1.2.2.1.1.3 |
lseIntPortMACAddListThis item contains MAC address (source addresses) of the port.
Each MAC address is 6 bytes long. The list is started with the MAC address
that follows the lseIntPortMACAddLAId.ro OCTET STRING ( SIZE .1.3.6.1.4.1.81.19.1.2.2.1.1.4 |
lseIntPortFilter OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.1.2.3 |
lseIntPortFilterTable SEQUENCE OF LseIntPortFilterEntry .1.3.6.1.4.1.81.19.1.2.3.1 |
lseIntPortFilterEntryThis table is supported only for the LSE-PM module.
The table reports the contents of the port's filtering
mechanism. LseIntPortFilterEntry .1.3.6.1.4.1.81.19.1.2.3.1.1 |
lseIntPortFilterGroupIdThis item is relevant only for the LSE-PM module. The
item defines the group to which the port belongs (i.e.,
the module number).ro INTEGER .1.3.6.1.4.1.81.19.1.2.3.1.1.1 |
lseIntPortFilterPortIdThis item is relevant only for the LSE-PM module. The
item defines the number of the LANswitch port in the
board.ro INTEGER .1.3.6.1.4.1.81.19.1.2.3.1.1.2 |
lseIntPortFilterLAIdThis item is relevant only for the LSE-PM module. The
item contains the lower 2 bytes of the Last MAC Address
on the previous list. Use the 0 value to start from the
beginning of the list.ro INTEGER .1.3.6.1.4.1.81.19.1.2.3.1.1.3 |
lseIntPortFilterListThis item is relevant only for the LSE-PM module. The
item contains the MAC addresses in the filter. Each
MAC address is 6 bytes long. The list is started with the
MAC address that follows the lseIntPortFilterLAId.ro OCTET STRING ( SIZE .1.3.6.1.4.1.81.19.1.2.3.1.1.4 |
lsePort OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.1.3 |
lsePortTable SEQUENCE OF LsePortEntry .1.3.6.1.4.1.81.19.1.3.1 |
lsePortEntryAn entry in the table containing data about a single external switch port. LsePortEntry .1.3.6.1.4.1.81.19.1.3.1.1 |
lsePortGroupIdId of the group to which the port belongs.ro INTEGER .1.3.6.1.4.1.81.19.1.3.1.1.1 |
lsePortIdNumber of LanSwitch port in the board.ro INTEGER .1.3.6.1.4.1.81.19.1.3.1.1.2 |
lsePortPolaritySetting the value of this attribute to ON activates the automatic port polarity
detection mode.rw Enumeration .1.3.6.1.4.1.81.19.1.3.1.1.3 |
lsePortBackboneStatusIt is the status of a single port that associated with a particular
Backbone port.
It is utilized by the Agent in the Soft Redundancy algorithm between
Backbone ports in LANswitch environmentrw Enumeration .1.3.6.1.4.1.81.19.1.3.1.1.4 |
lhs OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.2 |
lhsGroupTableTable with group-related parameters. SEQUENCE OF LhsGroupEntry .1.3.6.1.4.1.81.19.2.1 |
lhsGroupEntryEntry in the table. LhsGroupEntry .1.3.6.1.4.1.81.19.2.1.1 |
lhsGroupIdUnique slot identifier in which the module is located.ro INTEGER .1.3.6.1.4.1.81.19.2.1.1.1 |
lhsGroupMainSWVersionSoftware version of the main CPU.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.81.19.2.1.1.2 |
lhsGroupProtocolTypeThis attribute set the protocol type in which the LHB is collecting from
the high-speed bus.rw Enumeration .1.3.6.1.4.1.81.19.2.1.1.3 |
lhsPortTableTable with port-related parameters. SEQUENCE OF LhsPortEntry .1.3.6.1.4.1.81.19.2.2 |
lhsPortEntryEntry in the table. LhsPortEntry .1.3.6.1.4.1.81.19.2.2.1 |
lhsPortGroupIdSlot index in which the module is located.ro INTEGER .1.3.6.1.4.1.81.19.2.2.1.1 |
lhsPortIdPort number to which the data is related.ro INTEGER .1.3.6.1.4.1.81.19.2.2.1.2 |
lhsTxUCastNumber of unicast packets transmitted.ro Counter .1.3.6.1.4.1.81.19.2.2.1.3 |
lhsTxBCastNumber of broadcast packets transmitted.ro Counter .1.3.6.1.4.1.81.19.2.2.1.4 |
lhsTxMCastNumber of multicast packets transmitted.ro Counter .1.3.6.1.4.1.81.19.2.2.1.5 |
lhsTxUrunErrNumber of transmit packet underruns.ro Counter .1.3.6.1.4.1.81.19.2.2.1.6 |
lhsTxParErrNumber of transmit packet parity errors.ro Counter .1.3.6.1.4.1.81.19.2.2.1.7 |
lhsRxUCastNumber of unicast packets received.ro Counter .1.3.6.1.4.1.81.19.2.2.1.8 |
lhsRxBCastNumber of broadcast packets received.ro Counter .1.3.6.1.4.1.81.19.2.2.1.9 |
lhsRxMCastNumber of multicast packets received.ro Counter .1.3.6.1.4.1.81.19.2.2.1.10 |
lhsRxOrunErrNumber of receive overrun errors.ro Counter .1.3.6.1.4.1.81.19.2.2.1.11 |
lhsRxParErrNumber of receive parity errors.ro Counter .1.3.6.1.4.1.81.19.2.2.1.12 |
lhsRxRscErrNumber of receive resource errors.ro Counter .1.3.6.1.4.1.81.19.2.2.1.13 |
lhsRxBadTypeErrNumber of bad frame type packets received.ro Counter .1.3.6.1.4.1.81.19.2.2.1.14 |
lhsLinkStatusThis attribute describes the status of the optical link as detected
by the sensor software.ro Enumeration .1.3.6.1.4.1.81.19.2.2.1.15 |
lsMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.3 |
lsMonitorResourceAllocationThis item reports for which of the listed
monitoring activity CPU resources are
being allocated at this time. Activities that
are not in the above list are allocated resources at all times.ro Enumeration .1.3.6.1.4.1.81.19.3.1 |
lsBusStats OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.3.2 |
lsBusStatsDropEventsThe total number of events in which packets
were dropped by the probe due to lack of resources.
Note that this number is not necessarily the number of packets dropped;
it is just the number of times this condition has been detected.ro Counter .1.3.6.1.4.1.81.19.3.2.1 |
lsBusStatsPktsThe total number of packets (including error packets)
received on the LANswitch bus.ro Counter .1.3.6.1.4.1.81.19.3.2.2 |
lsBusStatsOctetsThe total number of octets of data (including
those in bad packets) received on the
LANswitch bus (excluding framing bits but including
FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.2.3 |
lsBusStatsUtilizationThe utilization of the LANswitch bus, expressed in percents
of the maximum possible LANswitch traffic.ro INTEGER .1.3.6.1.4.1.81.19.3.2.4 |
lsBusStatsEthBroadcastPktsThe total number of good Ethernet packets received that were
directed to the broadcast address.ro Counter .1.3.6.1.4.1.81.19.3.2.5 |
lsBusStatsMulticastPktsThe total number of good packets received that were
directed to a multicast address. Note that this
number does not include packets directed to the
broadcast address.ro Counter .1.3.6.1.4.1.81.19.3.2.6 |
lsBusStatsGoodEthPktsThe total number of good Ethernet packets received on the LANswitch bus.ro Counter .1.3.6.1.4.1.81.19.3.2.7 |
lsBusStatsGoodEthOctetsThe total number of octets that were received on the
LANswitch bus in good Ethernet packets (excluding framing bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.2.8 |
lsBusStatsBadEthPktsThe total number of bad Ethernet packets received on the LANswitch bus.ro Counter .1.3.6.1.4.1.81.19.3.2.9 |
lsBusStatsBadEthOctetsThe total number of octets that were received on the
LANswitch bus in bad Ethernet packets (excluding framing
bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.2.10 |
lsBusStatsNonEthPktsThe total number of packets received on the LANswitch
bus in non Ethernet packets.ro Counter .1.3.6.1.4.1.81.19.3.2.11 |
lsBusStatsNonEthOctetsThe total number of octets that were received on the
LANswitch bus in non Ethernet packets (excluding framing bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.2.12 |
lsBusStatsPriorityTableA list of priority count entries. SEQUENCE OF LsBusStatsPriorityEntry .1.3.6.1.4.1.81.19.3.2.13 |
lsBusStatsPriorityEntryA list of statistics related to a specific priority level on
the LANswitch bus. LsBusStatsPriorityEntry .1.3.6.1.4.1.81.19.3.2.13.1 |
lsBusStatsPriorityIndexThe priority for which this entry reports statistics .ro INTEGER .1.3.6.1.4.1.81.19.3.2.13.1.1 |
lsBusStatsPriorityPktsThe total number of packets (including error packets)
received on the LANswitch bus whose priority is that defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.2.13.1.2 |
lsBusStatsPriorityOctetsThe total number of octets (including error packets)
received on the LANswitch bus whose packets have the
priority defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.2.13.1.3 |
lsBusStatsVirtualNetListA bitmap defining the status of the virtual nets in the
Virtual NetTable. The first bit is for Virtual Net 0 and so
on. For existing virtual nets the bit is 1, otherwise 0.ro OCTET STRING .1.3.6.1.4.1.81.19.3.2.14 |
lsBusStatsVirtualNetTableA list of virtual net statistics. SEQUENCE OF LsBusStatsVirtualNetEntry .1.3.6.1.4.1.81.19.3.2.15 |
lsBusStatsVirtualNetEntryA list of staistics related to a specific virtual net which
exists on the LANswitch bus. LsBusStatsVirtualNetEntry .1.3.6.1.4.1.81.19.3.2.15.1 |
lsBusStatsVirtualNetThe virtual net for which this entry reports statistics .ro INTEGER .1.3.6.1.4.1.81.19.3.2.15.1.1 |
lsBusStatsVirtualNetPacketsThe number of good packets that were
transmitted to this virtual net by ports in this hub.ro Counter .1.3.6.1.4.1.81.19.3.2.15.1.2 |
lsBusStatsVirtualNetOctetsThe number of octets in good packets that
were transmitted to this virtual net by ports in this hub.ro Counter .1.3.6.1.4.1.81.19.3.2.15.1.3 |
lsPortStats OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.3.3 |
lsPortControlTableA list of port control entries. SEQUENCE OF LsPortControlEntry .1.3.6.1.4.1.81.19.3.3.1 |
lsPortControlEntryA list of parameters that set up the collection
of extended statistics related to LANswitch ports.
Data is collected in the lsPortExtendedStatsTable. LsPortControlEntry .1.3.6.1.4.1.81.19.3.3.1.1 |
lsPortControlIndexAn index that uniquely identifies an entry in
the lsPortControlTable. Each such entry defines
a function that monitors ports and places
statistics about them in the portTable on behalf
of this lsPortControlEntry.ro INTEGER .1.3.6.1.4.1.81.19.3.3.1.1.1 |
lsPortControlDataSourceThis object identifies the source of the data for
this instance of the port function.
The statistics in this group reflect all packets
on the LANswitch bus that are trasferred by the lsPortFilterTable.
This object may not be modified if the
associated lsPortControlStatus object is equal to valid(1).rw OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.3.3.1.1.2 |
lsPortControlTableSizeThe number of ports for which SW counters are
collected by the agent. This number is limited to 5.ro INTEGER .1.3.6.1.4.1.81.19.3.3.1.1.3 |
lsPortControlLastDeleteTimeThe value of sysUpTime when the last entry
was deleted from the portion of the portTable
associated with this lsPortControlEntry. If no
deletions have occurred, this value shall be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.19.3.3.1.1.4 |
lsPortControlOwnerThe entity that configured this entry and is
therefore using the resources assigned to it.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.81.19.3.3.1.1.5 |
lsPortControlStatusThe status of this lsPortControl entry.
If this object is not equal to valid(1), all
associated entries in the lsPortTable, shall be deleted by the agent.rw Enumeration .1.3.6.1.4.1.81.19.3.3.1.1.6 |
lsPortFilterTableA list of LANswitch ports to be monitored on the high-speed bus.
The OID of this table is a legitimate value for the
lsPortControlDataSource.
When this OID is a source for the host table, a port in the
table has the same meaning as an instruction to the agent
to collect statistics for all the hosts connected to that port.
The maximum size of this table is 5 entries SEQUENCE OF LsPortFilterEntry .1.3.6.1.4.1.81.19.3.3.2 |
lsPortFilterEntryAn entry in the filter table. LsPortFilterEntry .1.3.6.1.4.1.81.19.3.3.2.1 |
lsPortFilterThe port monitored on the LANswitch bus. The value
of this item is: (16*S-1)+P, where S is the slot number in
the hub (1..16) and P the port within the slot (1..N).ro INTEGER .1.3.6.1.4.1.81.19.3.3.2.1.1 |
lsPortFilterStatusThe status of this lsPortFilter entry. When the status is
valid, the port defined in the corresponding lsPortFilter is
a part of the filter.rw Enumeration .1.3.6.1.4.1.81.19.3.3.2.1.2 |
lsPortFilterTableClearSetting the value of this item to clear(2) causes the
agent to clear all entries in the PortFilterTable.rw Enumeration .1.3.6.1.4.1.81.19.3.3.3 |
lsPortTableA list of port entries. Each entry contains statistical
data pertaining to a single port. An entry is
maintained at all times for each of the LANswitch
ports that exist in the hub. This table is not controlled
by the lsPortControlTable. SEQUENCE OF LsPortEntry .1.3.6.1.4.1.81.19.3.3.4 |
lsPortEntryA collection of statistics for a particular LANswitch port. LsPortEntry .1.3.6.1.4.1.81.19.3.3.4.1 |
lsPortNumberThe monitored port. The value of this item is:
16*(S-1)+P, where S is the slot number in the hub (1..16)
and P the port within the slot (1..N).ro INTEGER .1.3.6.1.4.1.81.19.3.3.4.1.1 |
lsPortInPktsThe number of good packets transmitted through
this port into the LANswitch bus .ro Counter .1.3.6.1.4.1.81.19.3.3.4.1.2 |
lsPortInFCSErrorsThe number of packets with FCS errors transmitted
through this port into the LANswitch bus .ro Counter .1.3.6.1.4.1.81.19.3.3.4.1.3 |
lsPortInTooLongPktsThe number of packets longer than 1518 bytes
transmitted through this port into the LANswitch bus .ro Counter .1.3.6.1.4.1.81.19.3.3.4.1.4 |
lsPortInOctetsThe number of octets in good packets
(excluding framing bits but including FCS octets)
transmitted through this port into the LANswitch bus .ro Counter .1.3.6.1.4.1.81.19.3.3.4.1.5 |
lsPortInTotalErrorsThis item is a summation of all errors on this port.
It contains the total hardware errors related to a specific port.ro Counter .1.3.6.1.4.1.81.19.3.3.4.1.6 |
lsPortInCollisionsThis counter is incremented by one for any
CarrierEvent signal on the port for which the
CollisionEvent signal on this port is also asserted.ro Counter .1.3.6.1.4.1.81.19.3.3.4.1.7 |
lsPortExtendedReportingListA list of all ports in the hub for which
Extended statistics are currently reported. 16
bits in the bitmap are allocated for each slot in
the hub. The MSB is for port 1 of slot 1, and the
LSB is for port 16 of slot 16. The bit representing
ports for which extended statistics are now
reported has the value of 1, otherwise 0.ro OCTET STRING .1.3.6.1.4.1.81.19.3.3.5 |
lsPortExtendedStatsTableA list of port entries. SEQUENCE OF LsPortExtendedStatsEntry .1.3.6.1.4.1.81.19.3.3.6 |
lsPortExtendedStatsEntryA collection of statistics for a particular
LANswitch port. LsPortExtendedStatsEntry .1.3.6.1.4.1.81.19.3.3.6.1 |
lsPortExtendedStatsNumberThe monitored port.The value of this item is:
16*(S-1)+P, where S is the slot number in the
hub (1..16) and P the port within the slot (1..N).ro INTEGER .1.3.6.1.4.1.81.19.3.3.6.1.1 |
lsPortCreationOrderAn index that defines the relative ordering of
the discovery time of ports captured for a
particular lsPortControlEntry. This index shall
be between 1 and N, where N is the value of
the associated lsPortControlTableSize. The
ordering of the indexes is based on the order of
each entry's insertion into the table, in which
entries added earlier have a lower index value
than entries added later.
It is important to note that the order for a
particular entry may change as an (earlier) entry
is deleted from the table. Because this order may
change, management stations should make use of
the lsPortControlLastDeleteTime variable in the
lsPortControlEntry associated with the relevant
portion of the lsPortTable. By observing
this variable, the management station may
detect the circumstances where a previous
association between a value of
lsPortCreationOrder and a lsPortEntry may no
longer hold.ro INTEGER .1.3.6.1.4.1.81.19.3.3.6.1.2 |
lsPortIndexThe set of collected port statistics of which
this entry is a part. The set of ports
identified by a particular value of this
index is associated with the lsPortControlEntry
as identified by the same value of
lsPortControlIndex.ro INTEGER .1.3.6.1.4.1.81.19.3.3.6.1.3 |
lsPortOutPktsThe number of packets without errors
transmitted from the LANswitch bus to this port.ro Counter .1.3.6.1.4.1.81.19.3.3.6.1.4 |
lsPortInBroadcastPktsThe number of good Ethernet packets directed
towards the broadcast address that were
transmitted to the LANswitch bus through this port.ro Counter .1.3.6.1.4.1.81.19.3.3.6.1.5 |
lsPortInMulticastPktsThe number of good Ethernet packets
directed to a multicast address that were
transmitted to the LANswitch bus through this port.ro Counter .1.3.6.1.4.1.81.19.3.3.6.1.6 |
lsHostFilterTableA list of hosts to be monitored on the high-speed
bus by the RMON MIB hosts group. The OID of this
table is a legitimate value for the hostControlDataSource.
The size of the table is limited to 200 entries. SEQUENCE OF LsHostFilterEntry .1.3.6.1.4.1.81.19.3.4 |
lsHostFilterEntryAn entry in the filter table. LsHostFilterEntry .1.3.6.1.4.1.81.19.3.4.1 |
lsHostFilterAddressThe MAC address of a host monitored on the
high-speed bus.ro OCTET STRING .1.3.6.1.4.1.81.19.3.4.1.1 |
lsHostFilterStatusThe status of this lsHostFilter entry. When the status is
valid, the host defined in the corresponding lsHostFilter is
a part of the filter.rw Enumeration .1.3.6.1.4.1.81.19.3.4.1.2 |
lsHostFilterTableClearSetting the value of this item to clear(2) causes the
agent to clear all entries in the HostFilterTable.rw Enumeration .1.3.6.1.4.1.81.19.3.5 |
lsHostPortFilterTableA list of ports to be monitored on the high-speed bus.
The OID of this table is a legitimate value for the
hostControlDataSource.
When this OID is a source for the host table, a port in the
table has the same meaning as an instruction to the agent to
collect statistics for all the hosts connected to that port.
The size of this table is limited to 5 entries. SEQUENCE OF LsHostPortFilterEntry .1.3.6.1.4.1.81.19.3.6 |
lsHostPortFilterEntryAn entry in the filter table. LsHostPortFilterEntry .1.3.6.1.4.1.81.19.3.6.1 |
lsHostPortFilterThe port monitored on the LANswitch bus. The value
of this item is: 16*(S-1)+P, where S is the slot number in
the hub (1..16) and P the port within the slot (1..N).ro INTEGER .1.3.6.1.4.1.81.19.3.6.1.1 |
lsHostPortFilterStatusThe status of this lsHostPortFilter entry. When the
status is valid, the hosts defined by the corresponding
lsHostPortFilter are a part of the filter.rw Enumeration .1.3.6.1.4.1.81.19.3.6.1.2 |
lsHostPortFilterTableClearSetting the value of this item to clear(2) causes the
agent to clear all entries in the HostPortFilterTable.rw Enumeration .1.3.6.1.4.1.81.19.3.7 |
lsMatrixFilterTableA list of hosts to be monitored on the high-speed bus
by the RMON MIB matrix group. The OID of this table is a
legitimate value for the hostControlDataSource.
The size of the table is limited to 200 entries. SEQUENCE OF LsMatrixFilterEntry .1.3.6.1.4.1.81.19.3.8 |
lsMatrixFilterEntryAn entry in the filter table. LsMatrixFilterEntry .1.3.6.1.4.1.81.19.3.8.1 |
lsMatrixFilterAddressThe MAC address of a host monitored on the
high-speed bus.ro OCTET STRING .1.3.6.1.4.1.81.19.3.8.1.1 |
lsMatrixFilterStatusThe status of this lsMatrixFilter entry. When the status
is valid, the hosts defined by the corresponding
lsMatrixFilter are a part of the filter.rw Enumeration .1.3.6.1.4.1.81.19.3.8.1.2 |
lsMatrixFilterTableClearSetting the value of this item to clear(2) causes the
agent to clear all entries in the MatrixFilterTable.rw Enumeration .1.3.6.1.4.1.81.19.3.9 |
lsHostTimePortCorrTableAn addition to the RMON MIB's hostTimeTable. This table contains
a list of MAC addresses that were monitored on the high-speed bus
and the switch ports to which they are connected.
The index of this table is the same as for the standard RMON
hostTimeTable. Indexes are hostTimeCreationOrder and hostTimeIndex.
The MAC address is stored in hostTimeAddress.
The port to which the MAC address is connected
hostTimePortConnection. SEQUENCE OF LsHostTimePortCorrEntry .1.3.6.1.4.1.81.19.3.10 |
lsHostTimePortCorrEntryAn entry in the MAC to port correlation table. LsHostTimePortCorrEntry .1.3.6.1.4.1.81.19.3.10.1 |
hostTimeAddressThe physical address of this host.ro OCTET STRING .1.3.6.1.4.1.81.19.3.10.1.1 |
hostTimeCreationOrderAn index that uniquely identifies an entry in
the hostTime table among those entries associated
with the same hostControlEntry. This index shall
be between 1 and N, where N is the value of
the associated hostControlTableSize. The ordering
of the indexes is based on the order of each entry's
insertion into the table, in which entries added
earlier have a lower index value than entries added
later. Thus the management station has the ability to
learn of new entries added to this table without
downloading the entire table.
It is important to note that the index for a
particular entry may change as an (earlier) entry
is deleted from the table. Because this order may
change, management stations should make use of the
hostControlLastDeleteTime variable in the
hostControlEntry associated with the relevant
portion of the hostTimeTable. By observing
this variable, the management station may detect
the circumstances where a download of the table
may have missed entries, and where a previous
association between a value of hostTimeCreationOrder
and a hostTimeEntry may no longer hold.ro INTEGER .1.3.6.1.4.1.81.19.3.10.1.2 |
hostTimeIndexThe set of collected host statistics of which
this entry is a part. The set of hosts
identified by a particular value of this
index is associated with the hostControlEntry
as identified by the same value of hostControlIndex.ro INTEGER .1.3.6.1.4.1.81.19.3.10.1.3 |
hostTimePortConnectionThe switch port to which this hostTimeAddress is connected.
The coding of the port number varies for different hubs and
packplanes.
For the LANSwitch HSB the value of this item is:
The value of this item is: 32*(S-1)+P, where S is
the slot number in the hub and P the LANswitch
port within the slot (1.. 32).
For hosts whose port connection is not identified by the agent, the
value of this item will be 65,535ro INTEGER .1.3.6.1.4.1.81.19.3.10.1.4 |
lsHistoryTableA list of High Speed Bus history entries. SEQUENCE OF LsHistoryEntry .1.3.6.1.4.1.81.19.3.11 |
lsHistoryEntryAn historical sample of LANswitch statistics on a HSB.
This sample is associated with the historyControlEntry which set up
the parameters for a regular collection of these samples. LsHistoryEntry .1.3.6.1.4.1.81.19.3.11.1 |
lsHistoryIndexThe history of which this entry is a part. The history identified by a particular value of this
index is the same history as identified by the same value of historyControlIndex.ro INTEGER .1.3.6.1.4.1.81.19.3.11.1.1 |
lsHistorySampleIndexAn index that uniquely identifies the particular
sample this entry represents among all samples
associated with the same lshistoryControlEntry.
This index starts at 1 and increases by one as each new sample is taken.ro INTEGER .1.3.6.1.4.1.81.19.3.11.1.2 |
lsHistoryIntervalTimeThe value of sysUpTime when this bucket was sampled .ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.19.3.11.1.3 |
lsHistoryStatsDropEventsThe total number of events in which packets were dropped by the probe due to lack of
resources. Note that this number is not necessarily the number of packets dropped; it is
just the number of times this condition has been detected.ro Counter .1.3.6.1.4.1.81.19.3.11.1.4 |
lsHistoryStatsPktsThe total number of packets (including error packets) received on the LANswitch bus.ro Counter .1.3.6.1.4.1.81.19.3.11.1.5 |
lsHistoryStatsOctetsThe total number of octets of data (including those in bad packets) received on the
LANswitch bus (excluding framing bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.11.1.6 |
lsHistoryStatsEthBroadcastPktsThe total number of good Ethernet packets received that were directed to the broadcast
address.ro Counter .1.3.6.1.4.1.81.19.3.11.1.7 |
lsHistoryStatsEthMulticastPktsThe total number of good packets received that were directed to a multicast address.
Note that this number does not include packets directed to the broadcast address.ro Counter .1.3.6.1.4.1.81.19.3.11.1.8 |
lsHistoryStatsGoodEthPktsThe total number of good Ethernet packets received on the LANswitch bus.ro Counter .1.3.6.1.4.1.81.19.3.11.1.9 |
lsHistoryStatsGoodEthOctetsThe total number of octets that were received on the LANswitch bus in good
Ethernet packets (excluding framing bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.11.1.10 |
lsHistoryStatsBadEthPktsThe total number of bad Ethernet packets received on the LANswitch bus.ro Counter .1.3.6.1.4.1.81.19.3.11.1.11 |
lsHistoryStatsBadEthOctetsThe total number of octets that were received on the LANswitch bus in bad Ethernet packets (excluding framing bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.11.1.12 |
lsHistoryStatsNonEthPktsThe total number of packets received on the LANswitch bus in non Ethernet packets.ro Counter .1.3.6.1.4.1.81.19.3.11.1.13 |
lsHistoryStatsNonEthOctetsThe total number of octets that were received on the LANswitch bus in non Ethernet packets (excluding framing bits but including FCS octets).ro Counter .1.3.6.1.4.1.81.19.3.11.1.14 |
lsHistoryStatsPriority1PktsThe total number of packets (including error packets) received on the LANswitch
bus whose priority is that defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.15 |
lsHistoryStatsPriority1OctetsThe total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.16 |
lsHistoryStatsPriority2PktsThe total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.17 |
lsHistoryStatsPriority2OctetsThe total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.18 |
lsHistoryStatsPriority3PktsThe total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.19 |
lsHistoryStatsPriority3OctetsThe total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.20 |
lsHistoryStatsPriority4PktsThe total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.21 |
lsHistoryStatsPriority4OctetsThe total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.ro Counter .1.3.6.1.4.1.81.19.3.11.1.22 |
lsHistoryBusUtilizationThe utilization of the LANswitch bus, expressed in percents of the maximum LANswitch traffic possible.ro INTEGER .1.3.6.1.4.1.81.19.3.11.1.23 |
lst OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.4 |
lstIntPort OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.4.1 |
lstIntPortTable SEQUENCE OF LstIntPortEntry .1.3.6.1.4.1.81.19.4.1.1 |
lstIntPortEntryAn entry in the table, containing data about
a LANswitch port of LANswitch Token-Ring modules. LstIntPortEntry .1.3.6.1.4.1.81.19.4.1.1.1 |
lstIntPortGroupIdId of the group to which the switch port belongs.ro INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.1 |
lstIntPortIdSwitch port Id in modulero INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.2 |
lstIntPortSidebandModeEnable Sideband mode on internal port. In this mode,
MAC level management of all rings can be done.rw Enumeration .1.3.6.1.4.1.81.19.4.1.1.1.3 |
lstIntPortTotalOctetsTotal number of octets circling in the ring. It is the
sum of local octets, in octets and out octets.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.4 |
lstIntPortTotalTrafficTotal traffic in ring as part of the maximum possible
utilization, 4Mbps or 16Mbps, expressed in percents.
It is the sum of local traffic, in traffic and out traffic.ro INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.5 |
lstIntPortLocalOctetsNumber of octets local to the ring. The local traffic
includes only traffic between stations on the local ring.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.6 |
lstIntPortLocalTrafficLocal traffic in ring as part of the maximum possible
utilization, 4Mbps or 16Mbps, expressed in percents.
The local traffic includes only traffic between stations
on the local ring.ro INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.7 |
lstIntPortInOctetsNumber of octets passing in to the HSB from the ring.
The In traffic includes only traffic going from stations
on the local ring to stations on other rings.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.8 |
lstIntPortInTrafficIn traffic to the HSB from the ring as part of the
maximum possible utilization, 4Mbps or 16Mbps,
expressed in percents. The In traffic includes only
traffic going from stations on the local ring to
stations on other rings.ro INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.9 |
lstIntPortOutOctetsNumber of octets passing out from the HSB to
the ring. The Out traffic includes only traffic
going to stations on the local ring from stations
on other rings.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.10 |
lstIntPortOutTrafficOut traffic from the HSB to the ring as part
of the maximum possible utilization, 4Mbps or
16Mbps, expressed in percents. The Out traffic
includes only traffic going to stations on the
local ring from stations on other rings.ro INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.11 |
lstIntPortTotalFramesTotal number of frames in the ring.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.12 |
lstIntPortLostFramesNumber of lost frames because of Back Pressure.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.13 |
lstIntPortClaimFramesNumber of Claim-Token frames in the ring.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.16 |
lstIntPortPurgeFramesNumber of Ring-Purge frames in the ring.ro Counter .1.3.6.1.4.1.81.19.4.1.1.1.17 |
lstIntPortNormallyCloseOpenDefines the IO mode of the switch port:
normally close or normally open. When the
port is in 'normallyOpen' mode, all packets
enter the port regardless to CAM content.rw Enumeration .1.3.6.1.4.1.81.19.4.1.1.1.18 |
lstIntPortSlicingEnablePacket slicing mechanism for decreasing
the delay of packets transmission in the HSB.
Value 'on' enables the slicing mechanism.rw Enumeration .1.3.6.1.4.1.81.19.4.1.1.1.19 |
lstIntPortSliceLengthThe slice length in bytes. It determines
the delay of packet's transmission through
the HSB.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.20 |
lstIntPortUNAddrMAC address of the Upstream Neighbor
of the line interface.ro OCTET STRING .1.3.6.1.4.1.81.19.4.1.1.1.21 |
lstIntPortMACAddressMAC address of the line interface.ro OCTET STRING .1.3.6.1.4.1.81.19.4.1.1.1.22 |
lstIntPortSMPTransmitEnableEnable SMP MAC frame transmission by line
interface during single-station situation.rw Enumeration .1.3.6.1.4.1.81.19.4.1.1.1.23 |
lstIntPortIPGLengthNumber of bytes interval between frames
transmission of the line interface to the ring.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.24 |
lstIntPortBPDummyWindowThe time (in 0.25ms) between Dummy frames
sendings during Back Pressure situation of the
line interface.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.25 |
lstIntPortBPTokenWindowThe time (in 0.25ms) until Token release
during Back Pressure situation of the line
interface.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.26 |
lstIntPortTransmitWindowThe time (in 0.25ms) of line interface
transmission until Token release.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.27 |
lstIntPortBlockingPriorityThe priority of the line interface during
Back Pressure situation.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.28 |
lstIntPortNormalPriorityThe priority of the line interface for HSB
packets transmission into the ring.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.29 |
lstIntPortDummyMVContent of MV (Major Vector) field in Dummy
frame during Back Pressure of line interface.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.30 |
lstIntPortTxConsecutiveBusiesThreshThe threshold of the number of consecutive
busies counter.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.31 |
lstIntPortTxBufFullThreshThreshold indicator for frames buffer full.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.32 |
lstIntPortRxEmpty0Upper threshold pointer of Rx buffer.
Determines the degree of buffer overflow
and back pressure efficiency.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.33 |
lstIntPortRxEmpty1Middle threshold pointer of Rx buffer.
Determines the degree of buffer overflow
and back pressure efficiency..rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.34 |
lstIntPortRxEmpty2Lower threshold pointer of Rx buffer. Determines
the degree of buffer overflow and back pressure efficiency.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.35 |
lstIntPortRxFullRx full threshold pointer. Determines the degree
of buffer overflow and back pressure efficiency.rw INTEGER .1.3.6.1.4.1.81.19.4.1.1.1.36 |
lstIntPortBPEnableEnable/disable the Back Pressure mechanism.rw Enumeration .1.3.6.1.4.1.81.19.4.1.1.1.37 |
lstIntPortRouteSidebandSet the internal port ability to get from the HSB sideband packets. The
value 'on' enables the
routing of sideband packet from the HSB into the internal port.rw Enumeration .1.3.6.1.4.1.81.19.4.1.1.1.38 |
lseWANTableLAN Switch WAN data table. Implementation of this table is
mandatory for all LANswitch modules with WAN ports. SEQUENCE OF LseWANEntry .1.3.6.1.4.1.81.19.5 |
lseWANEntryEntry in the table. LseWANEntry .1.3.6.1.4.1.81.19.5.1 |
lseWANGroupIdSlot number in which the module is located.ro INTEGER .1.3.6.1.4.1.81.19.5.1.1 |
lseWANPortIdWAN port index.ro INTEGER .1.3.6.1.4.1.81.19.5.1.2 |
lseWANConnectionWAN connection status.ro Enumeration .1.3.6.1.4.1.81.19.5.1.3 |
lsVNChange OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.6 |
lsVNChangeMACAddressMAC Address that was detected with at
a switch port and its mapping to a Virtual
Network does not fit with the third layer
address.ro OCTET STRING .1.3.6.1.4.1.81.19.6.1 |
lsVNChangeDetectedVirtual Network number detected at the switch
port when a VN change is reported.ro INTEGER .1.3.6.1.4.1.81.19.6.2 |
lsVNChangeExpectedVirtual Network number detected at the switch
port when a VN change is reported.ro INTEGER .1.3.6.1.4.1.81.19.6.3 |
lsVNChangeGroupThe slot number of the card where the Vitual
Network change was detected.ro INTEGER .1.3.6.1.4.1.81.19.6.4 |
lsVNChangePortThe port number where the Vitual
Network change was detected.ro INTEGER .1.3.6.1.4.1.81.19.6.5 |
vnsPacket OBJECT IDENTIFIER .1.3.6.1.4.1.81.19.7 |
vnsPacketTableVNS packets data table. Implementation of this table is
mandatory for 3LS (3rd layer switch) module. SEQUENCE OF VnsPacketEntry .1.3.6.1.4.1.81.19.7.1 |
vnsPacketEntryEntry in the table. VnsPacketEntry .1.3.6.1.4.1.81.19.7.1.1 |
vnsPacketMACAddressThe Mac Address of the sending station.ro OCTET STRING ( SIZE (6)) .1.3.6.1.4.1.81.19.7.1.1.1 |
vnsPacketProtocolTypeMaskThis is a mask of the exising protocols.
Bit(0)='1' when IP protocol exist and '0' otherwise,
Bit(1)='1' when IPX protocol exist and '0' otherwise,
all other bits are '0' for the moment.ro OCTET STRING ( SIZE (1)) .1.3.6.1.4.1.81.19.7.1.1.2 |
vnsPacketIPAddressThe IP address of the packet's sending station.
In case the typeaddress is not IP this field will be 0.0.0.0.ro IpAddress .1.3.6.1.4.1.81.19.7.1.1.3 |
vnsPacketIPNetMaskThe IP Address Mask from the IP Interface Table.ro IpAddress .1.3.6.1.4.1.81.19.7.1.1.4 |
vnsPacketIPXnetworkThe IPX NetWork Address of the packet's sending station.
In case that the typeaddress is not IPX this field will be 0.0.0.0.ro OCTET STRING ( SIZE (4)) .1.3.6.1.4.1.81.19.7.1.1.5 |
vnsPacketStationTypeThe Station Type indicates from where comes the packets
in the case of the IPX protocol.ro Enumeration .1.3.6.1.4.1.81.19.7.1.1.6 |
vnsPacketPortGroupIdIndex which identifies the group inside the chassis for which this
entry contains information. It equals with the slot number.ro INTEGER .1.3.6.1.4.1.81.19.7.1.1.7 |
vnsPacketPortIdIndex which identifies the port inside the group for which this
entry contains information. It equals with the port number.ro INTEGER .1.3.6.1.4.1.81.19.7.1.1.8 |
vnsPacketBackbonePortThe value 2 indicates that the port source of the packet is a
backbone port.ro Enumeration .1.3.6.1.4.1.81.19.7.1.1.9 |
vnsPacketExpectedVLANThe value of this item is the VLAN number that the packet had to have
according to it's address.ro INTEGER .1.3.6.1.4.1.81.19.7.1.1.10 |
vnsPacketDetectedVLANThe value of this item is the detected VLAN number of the arrived packet.ro INTEGER .1.3.6.1.4.1.81.19.7.1.1.11 |
vnsPacketBoxAgentIPThe IP Address of the Hub's BoxAgent where the 3LS (3rd layer switch) module exist.ro IpAddress .1.3.6.1.4.1.81.19.7.1.1.12 |
lntTopology OBJECT IDENTIFIER .1.3.6.1.4.1.81.23 |
topDiscoveryThe value of this item defines the activity status of the agent's discovery algorithm.
When its value is set to topoMessages(2), the agent searches for the topology messages
(interhub and bridge messages).
When the value is macFind(3), the agent searches for the MAC addresses defined in
the item ethTopMACFindList. The results of the search are then reported in
ethTopMACResultTable.
When the value is swBackboneMsgMonitor(4), the agent monitors messages with
specific destination address. The result of monitoring is reported in ethTopMessageResultEntry.
The value of this item cannot be changed from one state to another without being
first changed to idle(1).
This item is timed by TopDiscoveryTimeOut (return back to idle(1)).rw Enumeration .1.3.6.1.4.1.81.23.1 |
topDiscoveryTimeOutThe value of this item defines the maximal time (in seconds) that an agent can remain in the non-idle toplogy discovery mode. When the agent is set to the topology mode (TopDiscovery=topoDiscovery(2) or macFind(3)) the counter is started. If the manager doesn't return the agent back to normal operation mode within the timeOut, the agent will automatically return to normal operation (TopDiscovery=idle(1)) and stop searching for the special messages.
The value of this item can be changed only when TopDiscovery=idle(1).rw INTEGER .1.3.6.1.4.1.81.23.2 |
ethTop OBJECT IDENTIFIER .1.3.6.1.4.1.81.23.3 |
ethTopDiscoveryTxThis item is a switch that activates the inter-agent topology messages.
txInterhubMsg(2) - the agent transmits interhub discovery messages.
txBridgeMsg(3) - the agent transmits bridge discovery messages.
txAckMsg(4) - the agent transmits acknowledgment messages.rw Enumeration .1.3.6.1.4.1.81.23.3.1 |
ethTopClearMessageResultWhen this item is set to clear(2), the agent sets the values of all ethTopMessageResult items to '0'. When finished the 'clear' process the Agent sets the variable to idle(1).rw Enumeration .1.3.6.1.4.1.81.23.3.2 |
ethTopNumOfMessageResultsThis item contains the number of messages
currently stored in the ethTopMessageResultTable.rw INTEGER .1.3.6.1.4.1.81.23.3.3 |
ethTopMessageResultTableA table that contains 3 items with the results of the topology messages received by the agent. SEQUENCE OF EthTopMessageResultEntry .1.3.6.1.4.1.81.23.3.4 |
ethTopMessageResultEntryAn entry in the table, containing part of the received data. EthTopMessageResultEntry .1.3.6.1.4.1.81.23.3.4.1 |
ethTopMessageResultIdThe table's index. Can assume the values 1,2, or 3.ro INTEGER .1.3.6.1.4.1.81.23.3.4.1.1 |
ethTopMessageResultA row in the Topology Messages result table. Each row contains up to 44 elements.ro OCTET STRING .1.3.6.1.4.1.81.23.3.4.1.2 |
ethTopMACFindListUp to 6 MAC addresses to be searched for by the Agent.rw OCTET STRING ( SIZE .1.3.6.1.4.1.81.23.3.5 |
ethTopMACFindResultTableA table that contains 4 rows with the results of the MACFind process. Each row contains the results for one of the hub's buses. The number of items supported is equal to the number of buses supported by the agent. SEQUENCE OF EthTopMACFindResultEntry .1.3.6.1.4.1.81.23.3.6 |
ethTopMACFindResultEntryAn entry in the table, containing one LSA item. EthTopMACFindResultEntry .1.3.6.1.4.1.81.23.3.6.1 |
ethTopMACFindBusThe bus for which the results are reported.ro INTEGER .1.3.6.1.4.1.81.23.3.6.1.1 |
ethTopMACFindResultThe results of the search for the requested MAC addresses fo the relevant bus. The format is: MAC (6 bytes), slot (1 byte), port (1 byte).
If the Agent doesn't find a MAC's correlation, the slot and port will be '0'.ro OCTET STRING ( SIZE .1.3.6.1.4.1.81.23.3.6.1.2 |
ethTopLSATableA table that contains 8 rows with the last source addresses found on the hub's ports.
Each row in the table reports the last source addresses for specific slots in the hub:
#1: modules 1,2,17,18; #5: modules 9,10,25, 26;
#2: modules 3,4,19,20; #6: modules 11,12,27, 28;
#3: modules 5,6,21,22; #7: modules 13,14,29,30;
#4: modules 7,8,23,24; #8: modules 15,16,31,32;
The data in the items appears by the slot order defined above. All 8 items exist even if some of them are empty. SEQUENCE OF EthTopLSAEntry .1.3.6.1.4.1.81.23.3.7 |
ethTopLSAEntryAn entry in the table, containing one LSA item. EthTopLSAEntry .1.3.6.1.4.1.81.23.3.7.1 |
ethTopLSAIdThe table's index. Assumes values 1,2,3,...,8.ro INTEGER .1.3.6.1.4.1.81.23.3.7.1.1 |
ethTopLSAThis item contains the last source addresses for modules in related slots. For each port the data is: slot (one byte), port (one byte), address (6 bytes). For none existing ports the LSA will be 0.
The first bit (MSB) of the slot byte defines the user status:
'0' - single user; '1' - multi user.ro OCTET STRING .1.3.6.1.4.1.81.23.3.7.1.2 |
ethTopAddressTableA table that contains the MAC addresses used by the agent for the topology
messages. SEQUENCE OF EthTopAddressEntry .1.3.6.1.4.1.81.23.3.8 |
ethTopAddressEntryAn entry in the topology address table. The number of entries is
equal to the number of Ethernet
buses supported by the agent. EthTopAddressEntry .1.3.6.1.4.1.81.23.3.8.1 |
ethTopBusThe bus for which this address is defined.ro INTEGER .1.3.6.1.4.1.81.23.3.8.1.1 |
ethTopAddressThe MAC address used by the agent for the topology discovery
process on the related bus.rw OCTET STRING .1.3.6.1.4.1.81.23.3.8.1.2 |
ethTopHSBMonitorThis item ask for monitoring the LANSwitch bus by the NMA-RS.
startMonitor(2) value, is used to start monitor the LANSwitch bus
collect the lsHostTimePortCorrTable.rw Enumeration .1.3.6.1.4.1.81.23.3.9 |
smon OBJECT IDENTIFIER .1.3.6.1.4.1.81.30 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.81.30.1 |
alarmMonitorStatusTableA list of alarms status for Alarm entries. SEQUENCE OF AlarmMonitorStatusEntry .1.3.6.1.4.1.81.30.1.1 |
alarmMonitorStatusEntryEach entry contains an index (appropriate to specific alarmIndex item)
and the alarmed status of this alarm entry AlarmMonitorStatusEntry .1.3.6.1.4.1.81.30.1.1.1 |
alarmMonitorStatusIndexAn index that uniquely identifies an entry in the alarmMonitorStatusTable.
This index is the same as the appropriate alarm Table.ro INTEGER .1.3.6.1.4.1.81.30.1.1.1.1 |
alarmMonitorStatusThe alarms' status for the appropriate alarm table
1 - ok
2 - alarmState.ro Enumeration .1.3.6.1.4.1.81.30.1.1.1.2 |
alarmUtilitiesCommandThe alarms command can be one of the follows:
1 - idle - idle state.
2 - clearAll - clear all alarms and events in the Agent tables.
254 - failed - If the Agent does not succeed to perform the command,
the alarmUtilitiesCommand will be changed to failed,
to indicate the fail of performing the last Command.rw Enumeration .1.3.6.1.4.1.81.30.1.2 |
portHistory OBJECT IDENTIFIER .1.3.6.1.4.1.81.30.3 |
portHistoryExtendedControlTableA list of extended history control entries. SEQUENCE OF PortHistoryExtendedControlEntry .1.3.6.1.4.1.81.30.3.1 |
portHistoryExtendedControlEntryA list of extended parameters that set up a periodic sampling of statistics. PortHistoryExtendedControlEntry .1.3.6.1.4.1.81.30.3.1.1 |
portHistoryExtendedControlCreateTimeThe value of sysUpTime at the creation of the control row and start of the history
collection index with the same value of the historyControlIndex.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.30.3.1.1.1 |
portHistoryExtendedControlLastBucketIndexThe index of the last bucket that was stored to the history table.ro INTEGER .1.3.6.1.4.1.81.30.3.1.1.2 |
portHistoryExtendedControlNumberOfBucketsThe number of buckets stored in the probe.ro INTEGER (0.. 2147483647) .1.3.6.1.4.1.81.30.3.1.1.3 |
portHistoryExtendedControlNameThe name of the this history collection.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.81.30.3.1.1.4 |
lsPortHistoryTableA list of LANswitch port history entries. SEQUENCE OF LsPortHistoryEntry .1.3.6.1.4.1.81.30.3.2 |
lsPortHistoryEntryAn historical sample of port switch statistics with the historyControlEntry,
which set up the parameters for a regular collection of these samples. LsPortHistoryEntry .1.3.6.1.4.1.81.30.3.2.1 |
lsPortHistoryIndexThe history of which this entry is a part. The history identified by a particular value of this
index is the same history as identified by the same value of historyControlIndex.ro INTEGER .1.3.6.1.4.1.81.30.3.2.1.1 |
lsPortHistorySampleIndexAn index that uniquely identifies the particular sample,
this entry represents among all samples associated with the same lshistoryControlEntry.
This index starts at 1 and increases by one as each new sample is taken.ro INTEGER .1.3.6.1.4.1.81.30.3.2.1.2 |
lsPortHistoryIntervalTimeThe value of sysUpTime at the start of the interval
over which this sample was measured.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.30.3.2.1.3 |
lsPortHistoryBoxConfigurationOctet String build by concatenating the genGroupType of the
maximum 16 modules in the LANSwitch box. By reading this
variable a management application can draw a list of the LANSwitch
modules and ports configuration relevant for the application.ro OCTET STRING .1.3.6.1.4.1.81.30.3.2.1.4 |
lsPortHistoryPktsThe total number of good packets received on the port.ro Counter .1.3.6.1.4.1.81.30.3.2.1.5 |
lsPortHistoryCollisionsThe best estimate of the total number of collisions
on this port during this sampling interval.ro Counter .1.3.6.1.4.1.81.30.3.2.1.6 |
lsPortHistoryTotalErrorsThe total number of errors detected by the switching hardware on this port,
including FCS errors and too long packets.ro Counter .1.3.6.1.4.1.81.30.3.2.1.7 |
scPortHistoryTableA list of Xswitch port history entries. SEQUENCE OF ScPortHistoryEntry .1.3.6.1.4.1.81.30.3.3 |
scPortHistoryEntryAn historical sample of port switch statistics with the historyControlEntry,
which set up the parameters for a regular collection of these samples. ScPortHistoryEntry .1.3.6.1.4.1.81.30.3.3.1 |
scPortHistoryIndexThe history of which this entry is a part. The history identified by a particular value of this
index is the same history as identified by the same value of historyControlIndex.ro INTEGER .1.3.6.1.4.1.81.30.3.3.1.1 |
scPortHistorySampleIndexAn index that uniquely identifies the particular sample,
this entry represents among all samples associated with the same scHistoryControlEntry.
This index starts at 1 and increases by one as each new sample is taken.ro INTEGER .1.3.6.1.4.1.81.30.3.3.1.2 |
scPortHistoryIntervalTimeThe value of sysUpTime at the start of the interval
over which this sample was measured.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.81.30.3.3.1.3 |
scPortHistoryBoxConfigurationOctet String build by concatenating the genGroupType of the
maximum 14 modules in the Meritage box or 4 boxes in the
Visage stack. By reading this variable a management application
can draw a list of the modules (boxes) and ports configuration
relevant for the application.ro OCTET STRING .1.3.6.1.4.1.81.30.3.3.1.4 |
scPortHistoryGoodPktsRecThe total number of good packets received by the port.ro Counter .1.3.6.1.4.1.81.30.3.3.1.5 |
scPortHistoryGoodNonUnicastPktsRecThe total number of good packets received that were
directed to multicat or broadcast address.ro Counter .1.3.6.1.4.1.81.30.3.3.1.6 |
scPortHistoryCollisionsThe best estimate of the total number of collisions on the
Ethernet segment connected to the port.ro Counter .1.3.6.1.4.1.81.30.3.3.1.7 |
scPortHistoryBadPktsThe total number of bad packets filtered by the port.
This item is the summation of:
scEthPortCRCAlignErrors, scEthPortOversizePkts,
scEthPortFragments and scEthPortJabber.ro Counter .1.3.6.1.4.1.81.30.3.3.1.8 |
scPortHistoryGoodPktsSentThe total number of good packets sent by the port.ro Counter .1.3.6.1.4.1.81.30.3.3.1.9 |
portHistoryMemoryAvailabilityThis item reflect the status of available Port History.
standard(1) value, is used when there are no memory limitations.
limited1(2) value, is used when the limitation is 3 MB.
limited1(3) value, is used when the limitation is 2 MB.ro Enumeration .1.3.6.1.4.1.81.30.3.4 |