Home/Catalog/XF-RADIOLINK-RLT-MIB

XF-RADIOLINK-RLT-MIB

AI MIB Summary

The XF-RADIOLINK-RLT-MIB provides SNMP management objects for monitoring Radio Link Terminals (RLT) and Carrier Terminations (CT) on Ericsson MINI-LINK TN radios, specifically enabling visibility into dual-carrier configuration states and operational parameters. This module facilitates the tracking of carrier-specific link metrics, including signal quality, error counters, and interface status for both primary and secondary carrier paths within the radio link application.

This MIB defines objects for Radio Link Terminal (RLT) and Carrier Termination (CT) for new Radio Link application in MINI-LINK TN supporting dual carrier capability.
Main OID:
xfRadioLinkRltMIB.1.3.6.1.4.1.193.81.3.4.5
368
Objects
Active
Status
9
Dependencies

Imported Objects

ENTITY-MIB
IF-MIB
SNMPv2-CONF
SNMPv2-SMI
PerfHist-TC-MIB
HC-PerfHist-TC-MIB
INET-ADDRESS-MIB
SNMPv2-TC
XF-TOP-MIB

Objects

368 total
Object Name
xfRadioLinkRltMIBThis MIB defines objects for Radio Link Terminal (RLT) and Carrier Termination (CT) for new Radio Link application in MINI-LINK TN supporting dual carrier capability.
MODULE-IDENTITY
.1.3.6.1.4.1.193.81.3.4.5
xfRadioLinkRltObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.193.81.3.4.5.1
xfChannelGroupTableThis table lists all relationships, for ech Channel Group (CG), between the Bonding/RLP interface and the RL WAN interface and allows to configure CG as either Bonding or Radio Link protection (RLP).
SEQUENCE OF XfChannelGroupEntry
.1.3.6.1.4.1.193.81.3.4.5.1.1
xfChannelGroupEntryAn entry in the xfChannelGroupTable.
XfChannelGroupEntry
.1.3.6.1.4.1.193.81.3.4.5.1.1.1
cgIfIndexIt is the ifIndex of WAN interface. The interface identified by atIfIndex is the same interface as identified by the same value of ifIndex.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.1.1.1
cgTypeIndexIndex representing the Channel Group interface type: - Bonding (2) - RLP: Radio Link Protection (3)ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.1.1.2
xfIfStatusThis object defines the Channel Group interface type: either Bonding or RLP (Radio Link Protection). Default: notReadyro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.1.1.3
xfLIMappingTableThis table is used when navigating from a logical entity to interface, representing the relationship between: - RLT logical entity and either Bonding/RLP interface; - Carrier Termination (CT) logical entity and RAU IF interface.
SEQUENCE OF XfLIMappingEntry
.1.3.6.1.4.1.193.81.3.4.5.1.2
xfLIMappingEntryAn entry in the xfLIMappingTable.
XfLIMappingEntry
.1.3.6.1.4.1.193.81.3.4.5.1.2.1
liEntLogicalIndexThe value of this object uniquely identifies the logical entity: RLT (Radio Link Terminal) and CT (Carrier Termination). The logical entity identified by liEntLogicalIndex is the same interface as identified by the same value of entLogicalIndex.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.2.1.1
liIfIndexIt represents the ifIndex of Bonding/RLP interface and RAU IF. The interface identified by liIfIndex is the same interface as identified by the same value of ifIndex.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.2.1.2
xfLINameIt represents the Name of the Radio Link Terminal (RLT) or Carrier Termination (CT).ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.2.1.3
xfLIIfDescrA textual string containing information about the ifDescr of both Channel Group interface (either Bonding or RLP (Radio Link Protection)) and RAU IF interface.ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.2.1.4
xfCarrierTerminationTableThis table is used to configure the Carrier Termination (CT).
SEQUENCE OF XfCarrierTerminationEntry
.1.3.6.1.4.1.193.81.3.4.5.1.3
xfCarrierTerminationEntryAn entry in the xfCarrierTerminationTable.
XfCarrierTerminationEntry
.1.3.6.1.4.1.193.81.3.4.5.1.3.1
xfCarrierTermDistinguishedNameIt represents the distinguished name of the Carrier Termination in the format Rack/Slot/CT.ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.1
xfCarrierTermLabelLabel identifying the Carrier Termination. It can be freely set by operator to label the Carrier Termination.rw
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.2
xfCarrierTermOperStatusIt represents the operative status of the Carrier Termination: - down(2) - up(3) - degraded(4) - testing(5)ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.3
xfCarrierTermRadioFrameIdIt represents the selected Radio Frame ID.rw
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.4
xfCarrierTermPreambleIt allows to set different preambles in the radio frame of each Carrier Termination in a XPIC or MIMO configuration: - preambleA(2) - preambleB(3) - preambleC(4) - preambleD(5) For non XPIC nor MIMO configurations, it can be left to notSpecified(1).rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.5
xfCarrierTermSelectedMinACMIt represents the selected minimum Tx ACM (Adaptive Code Modulation).rw
CarrierTermACMIndex
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.6
xfCarrierTermActualACMIt represents the actual (current) Tx ACM (Adaptive Code Modulation).ro
CarrierTermACMIndex
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.7
xfCarrierTermSelectedMaxACMIt represents the selected maximum Tx ACM (Adaptive Code Modulation).rw
CarrierTermACMIndex
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.8
xfCarrierTermCapabilitiesLastChangeThe value of sysUpTime at the time of the last creation or deletion of an entry in the xfCarrierTerminationCapabilityTable. If the number of entries has been unchanged since the last re-initialization of the local network management subsystem, then this object contains a zero value.ro
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.9
xfCarrierTermReferenceSECReference Spectrum Efficiency Class (SEC): - notSpecified(1): not configured, not possible to set - sec2(2): spectrum eff. Class 2 - sec4L(3): spectrum eff. Class 4L - sec4H(4): specturm eff. Class 4H - sec5LB(5): spectrum eff. Class 5LB - sec5HB(6): spectrum eff. Class 5HB - sec6LB(7): spectrum eff. Class 6LB - sec6HB(8): spectrum eff. Class 6HB - sec7B(9): spectrum eff. Class 7B In ETSI, a value different from notSpecified(1) must be configured. In ANSI, no value can be set and notSpecified(1) is always returned. Near end access: read-write. Far end access: read-write.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.10
xfCarrierTermWantedLicensedCapacityIt represents the wanted traffic licensed capacity on the Carrier Termination, expressed in Kbps. The default value 0 (i.e. disabled) means that no wanted licensed capacity has been selected by the user. The value used by RL license logic to request capacity licenses for the Carrier Termination is: - the capacity of selected max profile, if xfCarrierTermWantedLicensedCapacity = 0 - the value of xfCarrierTermWantedLicensedCapacity itself, if it is different from 0rw
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.11
xfCarrierTermActualLicensedCapacityThis MO represents the Actual Licensed Capacity used on the Carrier Termination: - if Wanted Licensed Capacity is disabled (i.e. xfCarrierTermWantedLicensedCapacity = 0), the Selected Max ACM (xfCarrierTermSelectedMaxACM MO) is used for requesting the license capacity on the carrier; - if Wanted Licensed Capacity is enabled (i.e. xfCarrierTermWantedLicensedCapacity > 0), the value of Wanted Licensed Capacity itself is used for requesting the license capacity on the carrier.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.12
xfCarrierTermActualCapacityIt represents the actual transmitted capacity supported by Carrier Termination in Kbps.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.13
xfCarrierTermPolarizationXPIC polarization, either horizontal or vertical.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.14
xfCarrierTermXPICOperStatusXPIC locking status: - Other(1): don't use - Locked(2): XPIC is locked: XPI valid - Unlocked(3): XPIC is not locked: XPI not valid - Mute(4): XPIC is muted (XPIC recovery started) - NotApplicable(5): XPIC is disabledro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.15
xfCarrierTermMIMOOperStatusMIMO locking status: - Other(1): don't use - Locked(2): MIMO is locked: XPI and SNIR valid - Unlocked(3): MIMO is not locked: XPI and SNIR not valid - Mute(4): MIMO is muted - NotApplicable(5): MIMO is disabledro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.16
xfCarrierTermSNIRSignal to Noise Interference Ratio (SNIR) in dB.ro
Integer32 --(-1000..1000)
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.17
xfCarrierTermXPICross-Polar Interference (XPI) level of the receiver in tenth of dB.ro
Integer32 --(-1000..1000)
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.18
xfCarrierTermResetReset command forces all the Carrier Termination settings to their own default.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.19
xfCarrierTermRestoreRestore command clears RFloop, IFloop and turns RAU transmitter on.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.20
xfCarrierTermAutoRemoveLoopEnableAuto remove all RL loops after 15 minutes.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.21
xfCarrierTermBerAlarmThresholdThreshold for BER alarm. Default: ber1e3(2).rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.22
xfCarrierTermActualRxACMIt represents the actual (current) Rx ACM (Adaptive Code Modulation).ro
CarrierTermACMIndex
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.23
xfCarrierTermFeCTSeverityThis object represents the highest severity of Far-End CT alarms and is populated only if Far-End terminal is represented by a Packet terminal (PT). Craft uses this MO to colour the box representing the Far-End CT in the hop view. In case of the Far-End is a TN, the remote highest alarm severity of CT is referred to the interfaces: RAU IF and RF IF.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.3.1.24
xfCarrierTerminationCapabilityTableThis table is used to configure the Carrier Termination (CT).
SEQUENCE OF XfCarrierTerminationCapabilityEntry
.1.3.6.1.4.1.193.81.3.4.5.1.4
xfCarrierTerminationCapabilityEntryAn entry in the xfCarrierTerminationCapabilityTable.
XfCarrierTerminationCapabilityEntry
.1.3.6.1.4.1.193.81.3.4.5.1.4.1
xfRadioFrameIdIt represents the Radio Frame Id.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.4.1.1
xfChannelSpacingChannel spacing: - ETSI: 3.5, 7, 14, 28, 40, 56, 112 MHz - ANSI: 10, 20, 30, 40, 50, 60, 80 MHzro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.4.1.2
xfFrameFormatTypeIt represents the Frame Format type: - Standard - XPIC - MIMO - Long Haul Standard - Long Haul XPIC - XPIC on two boards - Long Haul XPIC on two boardsro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.4.1.3
xfMinACMCapacityIt represents the minimum capacity designed for the specific frame format (Radio Frame Id).ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.4.1.4
xfMaxACMCapacityIt represents the maximum capacity designed for the frame format (Radio Frame Id).ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.4.1.5
xfACMProfileIt specifies which adaptive code and modulation profiles are supported.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.4.1.6
xfACMProfileCapacityTableThis tables reports the ACM capacities of the selected Radio Frame Id per each Carrier Termination.
SEQUENCE OF XfACMProfileCapacityEntry
.1.3.6.1.4.1.193.81.3.4.5.1.5
xfACMProfileCapacityEntryAn entry in the xfACMProfileCapacityTable.
XfACMProfileCapacityEntry
.1.3.6.1.4.1.193.81.3.4.5.1.5.1
xfACMIndexIt represents the positional index of the bitmap xfACMProfile in xfCarrierTerminationCapabilityTable.ro
CarrierTermACMIndex
.1.3.6.1.4.1.193.81.3.4.5.1.5.1.1
xfACMCapacityIt represents the capacity in Kbps of the ACM profile identified by the positional index xfACMIndex of the xfACMProfile in xfCarrierTerminationCapabilityTable. Value 0 means that the ACM profile is not included in current Frame Format.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.5.1.2
xfRLTTableThis table is used to configure the Radio Link Terminal (RLT).
SEQUENCE OF XfRLTEntry
.1.3.6.1.4.1.193.81.3.4.5.1.6
xfRLTEntryAn entry in the xfRLTTable.
XfRLTEntry
.1.3.6.1.4.1.193.81.3.4.5.1.6.1
rltEntLogicalIndexIt represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by rltEntLogicalIndex is the same entity as identified by the same value of entLogicalIndex.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.1
xfRLTDistinguishedNameIt represents the distinguished name of the Radio Link Terminal (RLT): Rack/Slot/RLT number. It is the ifName of RL-WAN i/f.ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.2
xfRLTIpAddressIPv4 address of the network element the Radio Link Terminal (RLT) belongs to.ro
IpAddress
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.3
xfRLTIPv6AddressIPv6 Address of the network element the Radio Link Terminal (RLT) belongs to.ro
InetAddressIPv6 (INET-ADDRESS-MIB)
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.4
xfRLTNeNameThe name of the network element the Radio Link Terminal (RLT) belongs to (System Name - sysName).ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.5
xfRLTNeTypeThe type of the network element the Radio Link Terminal (RLT) belongs to (System Descr - sysDescr).ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.6
xfRLTIdRadio Link Terminal (RLT) identifier used for integrity check with far-end.rw
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.7
xfRLTExpectedFarEndIdExpected Id of far-end Radio Link Terminal (RLT), used for integrity check with near-end.rw
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.8
xfRLTFarEndIdCheckWhen enabled, the system verifies that far-end Radio Link Terminal name is equal to the expected. If ok Radio Link Terminal status is UP. If not ok the Radio Link Terminal status is stated as DOWN. Default value: disabled.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.9
xfRLTStatusIt represents the operational status of the Radio Link Terminal (RLT).ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.10
xfRLTModeThe mode of the Radio Link Terminal (RLT). Values: - 1+0: onePlusZero (default) - 1+1 RLP: onePlusOneRadioLinkProtection - 2+0 RLB: twoPlusZeroAdvancedRadioLinkBonding - 1+1 RLP EQP: onePlusOneRadioLinkProtectionAndEquipmentProtection - 2+0 RLB EQP: twoPlusZeroRadioLinkBondingAndEquipmentProtection - 2+2 RLP EQP: twoPlusTwoRadioLinkProtectionAndEquipmentProtection - 4+0 RLB EQP: fourPlusZeroRadioLinkBondingAndEquipmentProtectionrw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.11
xfRLTActualTXTotalCapacityIt represents the total transmitted capacity throughput (considering both Packet and TDM traffic), expressed in bps, of the Radio Link Terminal (RLT).ro
Gauge32
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.12
xfRLTActualTXPacketCapacityIt represents the transmitted packet capacity throughput (only packet traffic), expressed in bps, of the Radio Link Terminal (RLT).ro
Gauge32
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.13
xfRLTLimitedTotalCapacityIt represents the total transmitted capacity throughput (considering both Packet and TDM traffic), expressed in bps, of the Radio Link Terminal (RLT) limited by License.ro
Gauge32
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.14
xfRLTRltSeverityThis object represents the highest severity alarm related to RLT with logical index 'rltEntLogicalIndex'. Node GUI uses the Far-End entry value (of this MIB MO) to define the colour of the Far-End RLT box in the hop view.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.15
xfRLTCapabilityEach bit of this object represents an RLT capability: Bit 0 - XPIC capability Bit 1 - TDM capability Bit 2 - CsPlurality capability Bit 3 - CtAutoSelection capability Bit 4 - OnePlusZero capability Bit 5 - OnePlusOneRadioLinkProtection capability Bit 6 - TwoPlusZeroAdvancedRadioLinkBonding capability Bit 7 - OnePlusOneRadioLinkProtectionWithEQP capability Bit 8 - TwoPlusZeroRadioLinkBondingWithEQP capability Bit 9 - TwoPlusTwoRadioLinkProtectionWithEQP capability Bit 10 - FourPlusZeroRadioLinkBondingWithEQP capability Bit 11 - XPIC between boards capability Bit 12 - XPIC Members Auto Selection capability Bit 13 - Manual EQP Switch capability Bit 14 - Enhanced ACM Protection: Maximum Capacity capability Bit 15 - Enhanced ACM Protection: Maximum Protection capability Bit 16 - Radio Link Encryption capability Bit 17 - MIMO capability Bit 18 - TX swicthover and SSD capabilityro
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.16
xfRLTInventoryLastChangeThe value of sysUpTime at the time of the last creation or deletion of an entry in the xfRLTHierarchyModuleTable. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.ro
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.17
xfRLTCpriModeSet the mode of the CPRI front-haul product. Default: notApplicable.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.18
xfRLTResetIt resets RLT to default configuration.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.19
xfRLTMeasuredHopLengthIt represents the measured value of the radio hop length expressed in Km. Values: - Radio hop length measurement not yet available: -1; - Measured hop length in Km: > 0.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.6.1.20
xfTrafficTableThis table is used to map the TDM interface to the specified RLT.
SEQUENCE OF XfTrafficEntry
.1.3.6.1.4.1.193.81.3.4.5.1.7
xfTrafficEntryAn entry in the xfTrafficEntry.
XfTrafficEntry
.1.3.6.1.4.1.193.81.3.4.5.1.7.1
trEntLogicalIndexIt represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by trEntLogicalIndex is the same interface as identified by the same value of entLogicalIndex.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.7.1.1
xfTDMEnableIt allows to map TDM interface to a specific Radio Link Terminal (RLT). Default: disable.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.7.1.2
xfRLTDMIfTableThis table is an extention of the ifTable used to configure TDM interface.
SEQUENCE OF XfRLTDMIfEntry
.1.3.6.1.4.1.193.81.3.4.5.1.8
xfRLTDMIfEntryAn entry in the xfRLTDMIfEntry.
XfRLTDMIfEntry
.1.3.6.1.4.1.193.81.3.4.5.1.8.1
xfRLTDMIfIndexIt is the ifIndex of RL TDM I/F table.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.1
xfActualTDMCapacityIt represents the current tributary capacity.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.2
xfWantedTDMAllocationIt represents the wanted tributary allocation.rw
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.3
xfActualTDMAllocationIt represents the actual tributary allocation.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.4
xfTDMIfAlarmsThis object shows TDM if related alarms.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.5
xfTDMRxLoopIt configures TDM RX loop: - other(1) - enable(2) - disable(3) (default)rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.6
xfTDMDistinguishedNameIt is the disinguished name of TDM i/f, i.e. R/S/P.ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.7
xfTDMMaxTributariesIt represents the maximum number of tributaries that can be allocated to TDM i/f, depending on frame ID, minimum ACM profile configured and licensed capacity in each CTs of the RLT. The maximum number is limited to 80.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.8
xfTDMHopLengthIt represents the length of the radio hop expressed in Km. This is used to calculate the propagation delay over the radio hop that shall be compensated to guarantee TDM traffic error free. Values: - default value for delay compensation: -1 - admissible range of values in Km: 0-200rw
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.8.1.9
xfCGIfTableThis table is an extension of ifTable reporting the main characteristics of CG i/f.
SEQUENCE OF XfCGIfEntry
.1.3.6.1.4.1.193.81.3.4.5.1.9
xfCGIfEntryAn entry in the xfCGIfEntry.
XfCGIfEntry
.1.3.6.1.4.1.193.81.3.4.5.1.9.1
xfCGIfIndexIt is the ifIndex of CG interface.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.9.1.1
xfCGIfMinSpeedThe minimum speed (throughput) of this interface expressed in bit/s, including both Ethernet and TDM capacities. Note: in case of bonding configurations, it represents the minimum of the min speeds of all Carrier Terminations in the bonding group.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.9.1.2
xfCGIfMaxSpeedThe maximum speed (throughput) of this interface expressed in bit/s, including both Ethernet and TDM capacities. Note: in case of bonding configurations, it represents the sum of the max speeds of all Carrier Terminations in the bonding group.ro
Gauge32
.1.3.6.1.4.1.193.81.3.4.5.1.9.1.3
xfCGIfRCNumNumber of Carrier Termination members belonging to the CG group.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.9.1.4
xfCGIfAlarmsThis object shows CG i/f related alarms.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.1.9.1.5
xfCGIfHopViewStatusThis object represents the Hop View status. Up: Far-End is reachable Down: Far-End not reachable The status is related to HCC-NE alarm.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.9.1.6
xfXPICPairTableThis table is used to enable XPIC (Admid Status) and set the CT pair in XPIC.
SEQUENCE OF XfXPICPairEntry
.1.3.6.1.4.1.193.81.3.4.5.1.10
xfXPICPairEntryAn entry in the xfXPICPairTable.
XfXPICPairEntry
.1.3.6.1.4.1.193.81.3.4.5.1.10.1
xpicPairEntLogicalIIndexIt represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by xpicPairEntLogicalIIndex is the same entity as identified by the same value of entLogicalIndex.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.1
xfXPICPairAdminStatusAdministrative status of XPIC pair. Default value: disable.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.2
xfXPICPairNumberIt specifies the number used for identification of the XPIC pair.rw
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.3
xfXPICPairRecoveryIt allows to enable/disable the recovery procedure when XPIC mode is enabled.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.4
xfXPICPairRestoreRestore XPIC functionality after XPIC recovery has been triggered and resets XPIC Auto Restore procedurerw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.5
xfXPICCTmember1It specifies the first Carrier Termination (CT) member of the XPIC pair. The member is identified by the CT distinguished name (R/S/P).rw
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.6
xfXPICCTmember2It specifies the second Carrier Termination (CT) member of the XPIC pair. The member is identified by the CT distinguished name (R/S/P).rw
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.7
xfXPICAutoRestoreIt enable/disables the XPIC Auto Recovery procedure.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.8
xfXpicPairIndexIt represents the table second index and is used to index the XPIC pair associated to Radio Link Terminal (RLT) with entLogicalIndex equal to xpicPairEntLogicalIIndex. It has been introduce to support configurations like 4+0 RLB EQP, 2+2 RLP EQP.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.10.1.9
xfMIMOGroupTableThis table is used to enable MIMO (Admid Status) and set the CTs in MIMO group.
SEQUENCE OF XfMIMOGroupEntry
.1.3.6.1.4.1.193.81.3.4.5.1.11
xfMIMOGroupEntryAn entry in the xfMIMOGroupTable.
XfMIMOGroupEntry
.1.3.6.1.4.1.193.81.3.4.5.1.11.1
mimoGroupEntLogicalIIndexIt represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by mimoGroupEntLogicalIIndex is the same entity as identified by the same value of entLogicalIndex.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.1
xfMIMOGroupAdminStatusAdministrative status of MIMO group. Default value: disable.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.2
xfMIMOGroupNumberIt specifies the Number used for identification of the MIMO group.rw
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.3
xfMIMOGroupRecoveryIt allows to enable/disable the recovery procedure when MIMO mode is enabled.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.4
xfMIMOGroupRestoreRestore MIMO functionality after MIMO recovery has been triggered.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.5
xfMIMOCTmember1It specifies the first Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P).ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.6
xfMIMOCTmember2It specifies the second Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P).ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.7
xfMIMOCTmember3It specifies the third Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P).ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.8
xfMIMOCTmember4It specifies the forth Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P).ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.11.1.9
xfRLWANIfTableThis table is used to handle the RL-WAN i/f.
SEQUENCE OF XfRLWANIfEntry
.1.3.6.1.4.1.193.81.3.4.5.1.12
xfRLWANIfEntryAn entry in the xfRLWANIfTable.
XfRLWANIfEntry
.1.3.6.1.4.1.193.81.3.4.5.1.12.1
xfRLWANIfIndexIt is the table index. It contains the ifIndex value of the WAN interface.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.1
xfRLWANDistinguishedNameIt is the name uniquely identifying the RL-WAN interface within the system, i.e. R/S/P.ro
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.2
xfRLWANCompAdminStatusIt enables and disables MLHC and PLC on the RL-WAN interface. down(2): both MLHC and PLC are disabled. mlhcUp(3): only MLHC is enabled. mlhcPlcUp(4): both MLHC and PLC are enabled. Default:down(2). Compression can be enabled on only one of the two RL-WAN interfaces belonging to the same MMU. Any attempt to enable compression on both RL-WAN interfaces belonging to the same MMU is refused.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.3
xfRLWANCompConnStatusIt specifies if the compression building block is physically connected to the RL-WAN interface. Physical connection of the compression building block to the RL-WAN interface is pre-requisite for enabling compression. When xfRLWANCompAdminStatus is set either to mlhcUp or mlhcPlcUp, the compression building block is physically connected to RL-WAN interfaces and xfRLWANCompConnStatus becomes connected. When xfRLWANCompAdminStatus is set either to mlhcUp or mlhcPlcUp on the other RL-WAN interface, the compression building block is physically connected to the other RL-WAN interfaces and xfRLWANCompConnStatus becomes disconnected.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.4
xfRLWANMlhcMplsModeIt specifies the wanted mpls mode. mplsOnly(2): Ethernet customer bridge, provider bridge and QinQ headers, including MPLS labels (up to 3) are compressed. controlWord(3): L2 VPN with Pseudo-Wire Control Word headers are compressed. l2(4): L2 VPN without Pseudo-Wire Control Word headers are compressed. l3(5): L3 VPN headers are compressed. Default: mplsOnly(2). This can be configured only if compression administrative status is down.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.5
xfRLWANMlhcOperStatusMulti-Layer Header Compression operative status.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.6
xfRLWANPlcOperStatusPayload Compression operative status.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.7
xfRLWANActualCapacityActual Capacity (speed) of RL WAN interface, in bps.ro
Gauge32
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.8
xfRLWANLimitedCapacityCapacity (speed) limited by license of RL WAN interface, in bps.ro
Gauge32
.1.3.6.1.4.1.193.81.3.4.5.1.12.1.9
xfRLTHierarchyModuleTableThis table is used to handle Module (MMU - RAU) hierarchy for the specific RLT.
SEQUENCE OF XfRLTHierarchyModuleEntry
.1.3.6.1.4.1.193.81.3.4.5.1.13
xfRLTHierarchyModuleEntryAn entry in the xfRLTHierarchyModuleTable.
XfRLTHierarchyModuleEntry
.1.3.6.1.4.1.193.81.3.4.5.1.13.1
xfRLTMHIndexIt is the table index. It contains the entPhisycalIndex of the WAN port associated to the RLT.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.1
xfRLTModuleIndexIt is the table index. It is a sequential number referred to the module (entity), either MMU or RAU, constituting the RLT.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.2
xfRLTEntPhysicalIndexThis MO represents the value of entPhysicalIndex of the module, either MMU or RAU, constituting the RLT.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.3
xfRLTPhysicalCointainedInThis MO represents the value of entPhysicalIndex for the physical entity which 'contains' this physical entity, which is either MMU or RAU (constituting the RLT).ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.4
xfRLTPhysicalParentRelPosThis MO represents the indication of the relative position of this 'child' component among all its 'sibling' components.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.5
xfRLTEntityPhysicalDescrThis MO represents a textual description of physical entity (module), either MMU or RAU, constituting the RLT.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.6
xfRLTModuleSlotPositionThis MO represents the slot position of the physical entity (module), either MMU or RAU, constituting the RLT.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.7
xfRLTFEDistinguishedNameThis MO represents the distinguished name of the Near-End logical entity, either RLT or CT.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.8
xfRLTNEDistinguishedNameThis MO represents the distinguished name of the Far-End logical entity, either RLT or CT.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.9
xfRLTInterfaceIndexThis MO represents the value of ifIndex of the interface, either CG IF (Bonding/RLP) or RAU IF, constituting the RLT.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.10
xfRLTHighestSeverityAlarmThis MO reports the highest severity of the alarms active in the physical module, MMU or RAU, it refers to. Value list: - critical(0): highest severity is Critical; - major(1): highest severity is Major; - minor(2): highest severity is Minor; - warning(3): highest severity is Warning; - clear(4): no alarm.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.13.1.11
xfRLTProtectionTableThis table is used to handle RL Protection for the RLT whose mode is set 1+1RLP.
SEQUENCE OF XfRLTProtectionEntry
.1.3.6.1.4.1.193.81.3.4.5.1.14
xfRLTProtectionEntryAn entry in the xfRLTProtectionTable.
XfRLTProtectionEntry
.1.3.6.1.4.1.193.81.3.4.5.1.14.1
xfRLTProtIndexIt is the table index. It contains the entity logical index of the RLT configured in 1+1RLP.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.1
xfRLTProtectionSwitchModeThe mode in which the switching mechanism is configured. Auto: System automatically switches from the degraded to the other transmitter (Tx). Manual: Automatic switching is disabled and operator can select Tx manually. Auto & Revertive: makes it possible to manually set the preferred Tx. TX switch disable: Selective Space Diverity, SSD. RLP TX switch is disabled. The two received signals, from different paths, are combined. Default: AUTO (for RLT mode RLP) & NA (default for RLT mode RLB).rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.2
xfRLTProtectionStatusStatus of the protection, when configured in a protected mode. Values: - unprotected; - protected - unableToProtect Note: Applicable only when RLT-mode is RL protection.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.3
xfRLTRevertivePreferredTXIt specifies the preferred TX Radio Carrier Termination (CT) in revertive protection mode. The member is identified by the CT distinguished name (R/S/P).rw
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.4
xfRLTProtectionWaitToRestoreTimeThe time, in # of seconds, to wait before switching back to the preferred Tx in Auto & Revertive mode. Default: 0.rw
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.5
xfRLTFadeNotificationTimerNotifications for alarms caused by fading, with a duration less than the specified time (0 - 1000 seconds) are not sent. Only applicable for protected configurations. Default: 200.rw
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.6
xfRLTManualSwitchCommandUsed to request a TX switch-over. Applicable for protected configurations and when protectionSwitchMode is set to Manual. Not Applicable for RLT mode RLB Value: - txManualSwitch - txManualNoSwitch.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.7
xfRLTTxSwitchOverConfigurationEnable or disable the function to switch TX on a request from far-end, including also the TX switchover alarm notifications , both local and remote. Only applicable in RLT mode RLP. Values: - notSupported: (default for RLT in RLB mode) - enable: TX switchover triggered by local and remote faults - disable: TX switchover disabled(default for RLT in RLP mode) - DEPRECATED - enableLocal: TX switchover triggered by local faults only (default for RLT in RLP mode)rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.8
xfRLTTxSwitchOverAlarmResetUsed to manual reset the TX switch-over alarm and Remote TX switchover alarm (consequently to TX switch ordered from far-end). Note: the alarm is raised when TX Switch far-end function is enabled (xfRLTTxSwitchOverConfiguration). Value: - txSwitchOverAlarmNoReset - txSwitchOverAlarmReset.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.9
xfRLTNumOfRLPSwitchIt represents the number of RLP Radio TX switch.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.10
xfRLTEnhancedACMProtectionModeIt configures the enhanced ACM protection mode. The enhanced ACM protection uses RX indicators from both the working and the protection links to select an ACM profile to optimize capacity (throughput) and/or protection (robustness). Values: - Active Transmitter : ACM engine determines the ACM profile according to the working Rx ACM indications only; - Maximum Capacity (default): Working Rx ACM engine is aware of the ACM profile requests from the protection Rx ACM engine, and determines the highest ACM profile between the working and the protection links; - Maximum Protection : Working Rx ACM engine is aware of the protection Rx ACM engine's ACM profile requests, and determines the lowest ACM profile between the working and the protection links.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.11
xfRLTEnhancedACMProtectionOperStatusStatus of the enhanched ACM protection engine, when ACM engine is configured either in maximum-troughtput or maximum-protection mode. Values: - notApplicable : when enhanced ACM protection mode is basic; - enhAcmProtActive : when the enhanced ACM engine is working and the highest ACM profile is selected between the working and the protection links; - enhAcmProtNotActive: when the enhanced ACM engine is not working.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.14.1.12
xfRLTEncryptionTableThis table is used to handle Radio Link Encryption.
SEQUENCE OF XfRLTEncryptionEntry
.1.3.6.1.4.1.193.81.3.4.5.1.15
xfRLTEncryptionEntryAn entry in the xfRLTEncryptionTable.
XfRLTEncryptionEntry
.1.3.6.1.4.1.193.81.3.4.5.1.15.1
xfRLTEncryptionIndexIt represents the xfRLTEncryptionTable index and is the RLT entity logical index.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.1.15.1.1
xfRLTEncryptionAdminStatusThis MO allows to enable/disable the Encryption of both control and traffic plain over the Radio Link hop. Values: - enable; - disable. Default: DISABLE.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.15.1.2
xfRLTEncryptionOperStatusThis MO represents the Operative Status of the Encryption function over the Radio Link hop and refers to receiving direction. Therefore, it indicates if the receiving side is able or not able to correctly/successfully decipher the ciphered data stream transmitted from remote side.. The ecryption status can assume the values: - up: control and traffic plain are correctly deciphered; - down: control and traffic plain are not deciphered correctly/successfully, due to e.g. authentication failure, disturbance over the radio-hop.ro
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.1.15.1.3
xfRLTEncryptionMasterKeyThis MO allows to define the Master Key used to initiate the Encryption operation. Master Key is hidden.rw
DisplayString
.1.3.6.1.4.1.193.81.3.4.5.1.15.1.4
xfRadioLinkRltPmObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.193.81.3.4.5.2
xfRLPMContinuousCounterTableTable for RLT performance data.
SEQUENCE OF XfRLPMContinuousCounterEntry
.1.3.6.1.4.1.193.81.3.4.5.2.1
xfRLPMContinuousCounterEntryAn entry in the xfRLPMContinuousCounterTable.
XfRLPMContinuousCounterEntry
.1.3.6.1.4.1.193.81.3.4.5.2.1.1
xfPMTimeElapsedThe number of seconds that have elapsed since the beginning of the current error-measurement period. If the current interval exceeds the maximum value, the agent will return the maximum value. Reset by xfPMPerfReset.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.1
xfPMCurrentESThis object shows the errored seconds. Reset by xfPMPerfReset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.2
xfPMCurrentSESThis object shows the severely errored seconds. Reset by xfPMPerfReset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.3
xfPMCurrentBBEThis object shows the background block errors. Reset by xfPMPerfReset.ro
HCPerfCurrentCount (HC-PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.4
xfPMCurrentUASThis object shows the unavailable seconds (or unavailable time). Reset by xfPMPerfReset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.5
xfPMCurrentBBThis object shows the background blocks. Reset by xfPMPerfReset.ro
HCPerfCurrentCount (HC-PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.6
xfPMPerfResetThis object is used to reset the performance counters: - Elapsed Time, ES, SES, BBE, BB - PM ACM - ETSI - EN 301 129 (TLTS, RLTS, ...) current/interval 15m/24h - Max and Min XPI/MSE current/interval 15m/24h It can be also set when the RAU is not present. Near end access: read-write.rw
Enumeration
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.7
xfPMCurrentESRThe ratio of ES to total seconds in available time during a fixed measurement interval. Reset by xfPMPerfReset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.8
xfPMCurrentSESRThe ratio of SES to total seconds in available time during a fixed measurement interval. Reset by xfPMPerfReset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.9
xfPMCurrentBBERThe ratio of Background Block Errors (BBE) to total blocks in available time during a fixed measurement interval. Reset by xfPMPerfReset.ro
HCPerfCurrentCount (HC-PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.1.1.10
xfRLPMACMConfigTableAlarm threshold values for RL PM.
SEQUENCE OF XfRLPMACMConfigEntry
.1.3.6.1.4.1.193.81.3.4.5.2.2
xfRLPMACMConfigEntryEntry in the xfRLPMACMConfigTable
XfRLPMACMConfigEntry
.1.3.6.1.4.1.193.81.3.4.5.2.2.1
xfPMACMSetThreshold15mThe 15 minute set threshold for minimum modulation. Near end access: read-write. Far end access: no access. Default value is 180.rw
Integer32
.1.3.6.1.4.1.193.81.3.4.5.2.2.1.1
xfPMACMSetThreshold24hThe 24 hour set threshold for minimum modulation. Near end access: read-write. Far end access: no access. Default value is 1500.rw
Integer32
.1.3.6.1.4.1.193.81.3.4.5.2.2.1.2
xfPMACMResetThreshold15mThe 15 minute reset threshold for minimum modulation. Near end access: read-write. Far end access: no access. Default value is 20.rw
Integer32
.1.3.6.1.4.1.193.81.3.4.5.2.2.1.3
xfPMACMStatusIt reports threshold crossing alarm status: - acm15m: ACM 15 min threshold crossing: ACM has been in the lowest configured profile for a number of seconds exceeding the configured 15 min threshold. - acm24h: ACM 24 hour threshold crossing: ACM has been in the lowest configured profile for a number of seconds exceeding the configured 24 hour threshold.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.2.2.1.4
xfPMACMValidDataIt reports which ACM's PM data are valid.ro
Bits
.1.3.6.1.4.1.193.81.3.4.5.2.2.1.5
xfRLPMACMCurrent24hTableACM-based counters for current 24h table.
SEQUENCE OF XfRLPMACMCurrent24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.3
xfRLPMACMCurrent24hEntryEntry in the xfRLPMACMCurrent24hTable.
XfRLPMACMCurrent24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.3.1
xfPMACMCurrent24h4QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.1
xfPMACMCurrent24h4QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.2
xfPMACMCurrent24h4QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.3
xfPMACMCurrent24h16QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.4
xfPMACMCurrent24h16QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.5
xfPMACMCurrent24h16QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.6
xfPMACMCurrent24h32QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.7
xfPMACMCurrent24h32QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.8
xfPMACMCurrent24h32QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.9
xfPMACMCurrent24h64QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.10
xfPMACMCurrent24h64QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.11
xfPMACMCurrent24h64QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.12
xfPMACMCurrent24h128QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.13
xfPMACMCurrent24h128QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.14
xfPMACMCurrent24h128QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.15
xfPMACMCurrent24h256QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.16
xfPMACMCurrent24h256QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.17
xfPMACMCurrent24h256QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.18
xfPMACMCurrent24h512QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.19
xfPMACMCurrent24h512QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.20
xfPMACMCurrent24h512QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.21
xfPMACMCurrent24h1024QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.22
xfPMACMCurrent24h1024QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.23
xfPMACMCurrent24h1024QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.24
xfPMACMCurrent24h2048QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.25
xfPMACMCurrent24h2048QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.26
xfPMACMCurrent24h2048QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.27
xfPMACMCurrent24h4096QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.28
xfPMACMCurrent24h4096QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.29
xfPMACMCurrent24h4096QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.30
xfPMACMCurrent24h8192QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.31
xfPMACMCurrent24h8192QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.32
xfPMACMCurrent24h8192QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.33
xfPMACMCurrent24h16384QAMStrongValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.34
xfPMACMCurrent24h16384QAMStdValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.35
xfPMACMCurrent24h16384QAMLightValid time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.3.1.36
xfRLPMACMInterval24hTableACM-based counters for interval 24h table.
SEQUENCE OF XfRLPMACMInterval24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.4
xfRLPMACMInterval24hEntryEntry in the xfRLPMACMInterval24hTable.
XfRLPMACMInterval24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.4.1
xfPMACMInterval24h4QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.1
xfPMACMInterval24h4QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.2
xfPMACMInterval24h4QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.3
xfPMACMInterval24h16QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.4
xfPMACMInterval24h16QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.5
xfPMACMInterval24h16QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.6
xfPMACMInterval24h32QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.7
xfPMACMInterval24h32QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.8
xfPMACMInterval24h32QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.9
xfPMACMInterval24h64QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.10
xfPMACMInterval24h64QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.11
xfPMACMInterval24h64QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.12
xfPMACMInterval24h128QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.13
xfPMACMInterval24h128QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.14
xfPMACMInterval24h128QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.15
xfPMACMInterval24h256QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.16
xfPMACMInterval24h256QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.17
xfPMACMInterval24h256QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.18
xfPMACMInterval24h512QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.19
xfPMACMInterval24h512QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.20
xfPMACMInterval24h512QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.21
xfPMACMInterval24h1024QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.22
xfPMACMInterval24h1024QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.23
xfPMACMInterval24h1024QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.24
xfPMACMInterval24h2048QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.25
xfPMACMInterval24h2048QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.26
xfPMACMInterval24h2048QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.27
xfPMACMInterval24h4096QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.28
xfPMACMInterval24h4096QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.29
xfPMACMInterval24h4096QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.30
xfPMACMInterval24hValidDataThis variable indicates whether the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.31
xfPMACMInterval24h8192QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.32
xfPMACMInterval24h8192QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.33
xfPMACMInterval24h8192QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.34
xfPMACMInterval24h16384QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.35
xfPMACMInterval24h16384QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.36
xfPMACMInterval24h16384QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.4.1.37
xfRLPMACMCurrent15mTableACM-based counters for current 15m table.
SEQUENCE OF XfRLPMACMCurrent15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.5
xfRLPMACMCurrent15mEntryEntry in the table.
XfRLPMACMCurrent15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.5.1
xfPMACMCurrent15m4QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.1
xfPMACMCurrent15m4QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.2
xfPMACMCurrent15m4QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.3
xfPMACMCurrent15m16QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.4
xfPMACMCurrent15m16QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.5
xfPMACMCurrent15m16QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.6
xfPMACMCurrent15m32QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.7
xfPMACMCurrent15m32QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.8
xfPMACMCurrent15m32QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.9
xfPMACMCurrent15m64QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.10
xfPMACMCurrent15m64QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.11
xfPMACMCurrent15m64QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.12
xfPMACMCurrent15m128QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.13
xfPMACMCurrent15m128QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.14
xfPMACMCurrent15m128QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.15
xfPMACMCurrent15m256QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.16
xfPMACMCurrent15m256QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.17
xfPMACMCurrent15m256QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.18
xfPMACMCurrent15m512QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.19
xfPMACMCurrent15m512QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.20
xfPMACMCurrent15m512QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.21
xfPMACMCurrent15m1024QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.22
xfPMACMCurrent15m1024QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.23
xfPMACMCurrent15m1024QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.24
xfPMACMCurrent15m2048QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.25
xfPMACMCurrent15m2048QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.26
xfPMACMCurrent15m2048QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.27
xfPMACMCurrent15m4096QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.28
xfPMACMCurrent15m4096QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.29
xfPMACMCurrent15m4096QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.30
xfPMACMCurrent15m8192QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.31
xfPMACMCurrent15m8192QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.32
xfPMACMCurrent15m8192QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.33
xfPMACMCurrent15m16384QAMStrongValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.34
xfPMACMCurrent15m16384QAMStdValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.35
xfPMACMCurrent15m16384QAMLightValid interval time since reset.ro
PerfCurrentCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.5.1.36
xfRLPMACMInterval15mTableACM-based counters for interval 15m table.
SEQUENCE OF XfRLPMACMInterval15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.6
xfRLPMACMInterval15mEntryEntry in the table.
XfRLPMACMInterval15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.6.1
xfPMACMInterval15mIntervalNumberA number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.ro
Integer32
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.1
xfPMACMInterval15m4QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.2
xfPMACMInterval15m4QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.3
xfPMACMInterval15m4QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.4
xfPMACMInterval15m16QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.5
xfPMACMInterval15m16QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.6
xfPMACMInterval15m16QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.7
xfPMACMInterval15m32QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.8
xfPMACMInterval15m32QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.9
xfPMACMInterval15m32QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.10
xfPMACMInterval15m64QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.11
xfPMACMInterval15m64QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.12
xfPMACMInterval15m64QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.13
xfPMACMInterval15m128QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.14
xfPMACMInterval15m128QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.15
xfPMACMInterval15m128QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.16
xfPMACMInterval15m256QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.17
xfPMACMInterval15m256QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.18
xfPMACMInterval15m256QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.19
xfPMACMInterval15m512QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.20
xfPMACMInterval15m512QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.21
xfPMACMInterval15m512QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.22
xfPMACMInterval15m1024QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.23
xfPMACMInterval15m1024QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.24
xfPMACMInterval15m1024QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.25
xfPMACMInterval15m2048QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.26
xfPMACMInterval15m2048QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.27
xfPMACMInterval15m2048QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.28
xfPMACMInterval15m4096QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.29
xfPMACMInterval15m4096QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.30
xfPMACMInterval15m4096QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.31
xfPMACMInterval15mValidDataThis variable indicates whether the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.32
xfPMACMInterval15m8192QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.33
xfPMACMInterval15m8192QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.34
xfPMACMInterval15m8192QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.35
xfPMACMInterval15m16384QAMStrongInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.36
xfPMACMInterval15m16384QAMStdInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.37
xfPMACMInterval15m16384QAMLightInterval count.ro
PerfIntervalCount (PerfHist-TC-MIB)
.1.3.6.1.4.1.193.81.3.4.5.2.6.1.38
xfRLPMMimoCurrentTableTable for RLT MIMO Current performance data.
SEQUENCE OF XfRLPMMimoCurrentEntry
.1.3.6.1.4.1.193.81.3.4.5.2.7
xfRLPMMimoCurrentEntryAn entry in the xfRLPMMimoCurrentTable.
XfRLPMMimoCurrentEntry
.1.3.6.1.4.1.193.81.3.4.5.2.7.1
xfPMPerfCurrentEtaPerformance Monitoring for Current MIMO Eta Value.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.7.1.1
xfPMPerfEtaMinLast7daysIndicate ETA Min level for the last 7 days.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.7.1.2
xfPMPerfEtaMaxLast7daysIndicate ETA Max level for the last 7 days.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.7.1.3
xfRLPMMimoCurrent24hTableCounters for Eta in current 24h.
SEQUENCE OF XfRLPMMimoCurrent24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.8
xfRLPMMimoCurrent24hEntryEntry in the xfRLPMMimoCurrent24hTable.
XfRLPMMimoCurrent24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.8.1
xfPMPerfCurrent24hElapsedTimeThe number of seconds that have elapsed since the beginning of the current error-measurement period.ro
Counter32
.1.3.6.1.4.1.193.81.3.4.5.2.8.1.1
xfPMPerfCurrent24hEtaMinPerformance Monitoring for MIMO Eta Min Value in Current 24h.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.8.1.2
xfPMPerfCurrent24hEtaMaxPerformance Monitoring for Current MIMO 24h Eta Max Value.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.8.1.3
xfRLPMMimoInterval24hTablePerformance Monitoring for MIMO Eta Min Value in Interval of 24h.
SEQUENCE OF XfRLPMMimoInterval24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.9
xfRLPMMimoInterval24hEntryEntry in the xfRLPMMimoInterval24hTable.
XfRLPMMimoInterval24hEntry
.1.3.6.1.4.1.193.81.3.4.5.2.9.1
xfPMPerfInterval24hValidDataThis variable indicates whether the data for this interval is valid.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.9.1.1
xfPMPerfInterval24hEtaMinPerformance Monitoring for MIMO Eta Min Value in Interval of 24h.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.9.1.2
xfPMPerfInterval24hEtaMaxPerformance Monitoring for MIMO Eta Max Value in Interval of 24h.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.9.1.3
xfRLPMMimoCurrent15mTableCounters for Eta MIMO Current 15m table.
SEQUENCE OF XfRLPMMimoCurrent15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.10
xfRLPMMimoCurrent15mEntryEntry in the table.
XfRLPMMimoCurrent15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.10.1
xfPMPerfCurrent15mElapsedTimeThe number of seconds that have elapsed since the beginning of the current error-measurement periodro
Counter32
.1.3.6.1.4.1.193.81.3.4.5.2.10.1.1
xfPMPerfCurrent15mEtaMinPerformance Monitoring for MIMO Eta Min Value in Current 15m.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.10.1.2
xfPMPerfCurrent15mEtaMaxPerformance Monitoring for MIMO Eta Max Value in Current 15m.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.10.1.3
xfRLPMMimoInterval15mTableCounters for Eta MIMO for Interval 15m.
SEQUENCE OF XfRLPMMimoInterval15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.11
xfRLPMMimoInterval15mEntryEntry in the table.
XfRLPMMimoInterval15mEntry
.1.3.6.1.4.1.193.81.3.4.5.2.11.1
xfPMPerfInterval15mIntervalNumberA number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.11.1.1
xfPMPerfInterval15mEtaMinPerformance Monitoring for MIMO Eta Min Value in Interval 15m.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.11.1.2
xfPMPerfInterval15mEtaMaxPerformance Monitoring for MIMO Eta Max Value in Interval 15m.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.11.1.3
xfPMPerfInterval15mValidDataThis variable indicates whether the data for this interval is valid.ro
INTEGER
.1.3.6.1.4.1.193.81.3.4.5.2.11.1.4
xfRadioLinkRltConformance
OBJECT IDENTIFIER
.1.3.6.1.4.1.193.81.3.4.5.3
xfRadioLinkRltCompliances
OBJECT IDENTIFIER
.1.3.6.1.4.1.193.81.3.4.5.3.1
xfRadioLinkRltFullComplianceThe compliance statement for SNMP entities which implement everything.
Unknown
.1.3.6.1.4.1.193.81.3.4.5.3.1.1
xfRadioLinkRltGroups
OBJECT IDENTIFIER
.1.3.6.1.4.1.193.81.3.4.5.3.2
xfRadioLinkRltCompleteGroupA collection of all current objects in this MIB module
Unknown
.1.3.6.1.4.1.193.81.3.4.5.3.2.1
XF-RADIOLINK-RLT-MIB - SNMP MIB Reference | MIBs Explorer