WWP-LEOS-RSVPTE-MIB
AI MIB Summary
The WWP-LEOS-RSVPTE-MIB monitors RSVP-TE signaling parameters on Wind River (WWP) LEOS network devices, specifically tracking interface hello intervals, hello tolerance thresholds, and advertised label values for traffic engineering path establishment.
Added new objects wwpLeosRsvpteIfHelloInterval,wwpLeosRsvpteIfHelloTolerance, wwpLeosRsvpteIfAdvertisedLabel.
Main OID:
wwpLeosRsvpteMIB.1.3.6.1.4.1.6141.2.60.30
32
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
32 total| Object Name |
|---|
wwpLeosRsvpteMIBAdded new objects wwpLeosRsvpteIfHelloInterval,wwpLeosRsvpteIfHelloTolerance, wwpLeosRsvpteIfAdvertisedLabel. MODULE-IDENTITY .1.3.6.1.4.1.6141.2.60.30 |
wwpLeosRsvpteMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.60.30.1 |
wwpLeosRsvpteObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.60.30.1.1 |
wwpLeosRsvpteAdminStatusThe desired administrative state of RSVP-TE.rw Enumeration .1.3.6.1.4.1.6141.2.60.30.1.1.1 |
wwpLeosRsvpteOperStatusThe current operational state of RSVP-TE.ro Enumeration .1.3.6.1.4.1.6141.2.60.30.1.1.2 |
wwpLeosRsvpteRetryIntervalThe persistent tunnel retry interval. This is the interval between the first failure of a persistent tunnel and the first attempt to re-establish the tunnel. This cannot be changed while admin status is enable or oper status is uprw Unsigned32 .1.3.6.1.4.1.6141.2.60.30.1.1.3 |
wwpLeosRsvpteRetryInfiniteStateThe persistent tunnel retry infinity. This is the State which when on will trigger RSVP-TE to try to restore the tunnels infinite times. This object can only be set if RSVP-TE is globally disabled.rw Enumeration .1.3.6.1.4.1.6141.2.60.30.1.1.4 |
wwpLeosRsvpteRetryMaxThe maximum number of retry attempts that will be made before a persistent tunnel is deemed inoperable. Once in this state, a management agent should set mplsTunnelAdminStatus to 'up' to attempt to reestablish the tunnel. This field is not used when wwpLeosRsvpteRetryInfiniteState is onro INTEGER .1.3.6.1.4.1.6141.2.60.30.1.1.5 |
wwpLeosRsvpteRefreshIntervalThis RSVP-TE value, R, which is used to set the average interval between refresh path and resv messages.ro Integer32 UNITS "milliseconds" .1.3.6.1.4.1.6141.2.60.30.1.1.6 |
wwpLeosRsvpteRefreshMultipleThe RSVP-TE value, K, which is the number of unresponded Path or Resv refresh attempts which must be made, spaced by the refresh interval before the state is deemed to have timed out.ro Integer32 .1.3.6.1.4.1.6141.2.60.30.1.1.7 |
wwpLeosRsvpteRfrshSlewDenomThe denominator of the fraction, SlewMax, which is the maximum allowable increase in the refresh interval, R, to prevent state timeout while changing R. R is increased by this fraction until it reaches the new desired value.ro Integer32 .1.3.6.1.4.1.6141.2.60.30.1.1.8 |
wwpLeosRsvpteRfrshSlewNumeratorThe numerator of the fraction, SlewMax, which is the maximum allowable increase in the refresh interval, R, to prevent state timeout while changing R. R is increased by this fraction until it reaches the new desired value.ro Integer32 .1.3.6.1.4.1.6141.2.60.30.1.1.9 |
wwpLeosRsvpteBlockadeMultipleThe RSVP-TE value, Kb, which is the number of refresh timeout periods after which blockade state is deleted.ro Integer32 .1.3.6.1.4.1.6141.2.60.30.1.1.10 |
wwpLeosRsvpteLSPSetupPriorityThe setup priority to apply to LSPs which are not signalling this parameter. 0 represents the highest priority, 7 the lowest. The value of this object must be numerically more or equal (so lower or equal priority) than the value of the holding priority object.ro Integer32 .1.3.6.1.4.1.6141.2.60.30.1.1.11 |
wwpLeosRsvpteLSPHoldingPriorityThe holding priority to apply to LSPs which are not signalling this parameter. 0 represents the highest priority, 7 the lowest. The value of this object must be numerically less or equal (so higher or equal priority) than the value of the holding priority object.ro Integer32 .1.3.6.1.4.1.6141.2.60.30.1.1.12 |
wwpLeosRsvpteUseHopByHopA flag to indicate that RSVP-TE should use the hop by hop addressing scheme for PATH and PATH-TEAR messages it sends. If set then the IP addresses used in the IP header of PATH messages forwarded by RSVP-TE set source as the local outgoing interface IP address, and destination as the next hop router IP address.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6141.2.60.30.1.1.13 |
wwpLeosRsvpteRestartCapableA flag to indicate whether the local node should advertise itself as restart capable.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6141.2.60.30.1.1.14 |
wwpLeosRsvpteRestartTimeThe time in milliseconds that the local node takes to restart RSVP-TE and the communication channel used for RSVP-TE communication. This is advertised to neighbors in the Restart_Cap object in Hello messages. Only used if wwpLeosRsvpteRestartCapable is set to true.ro Unsigned32 .1.3.6.1.4.1.6141.2.60.30.1.1.15 |
wwpLeosRsvpteRecoveryTimeThe period of time in milliseconds that the local node would like neighbors to take to resyncronize RSVP-TE and MPLS forwarding information after the re-establishment of Hello connectivity. This is advertised to neighbors in the Restart_Cap object in Hello messages. A value of zero indicates that the node does not support resynchronization following failure of the local node. A value of 0xFFFFFFFF indicates an infinite recovery time. Only used if wwpLeosRsvpteRestartCapable is set to true.ro Unsigned32 .1.3.6.1.4.1.6141.2.60.30.1.1.16 |
wwpLeosRsvpteMinPeerRestartThe mininum period of time in milliseconds that RSVP-TE should wait for a restart capable neighbor to regain Hello connectivity before invoking procedures related to communication loss. RSVP-TE will wait for the maximum of this time and the restart_time advertised in the RESTART_CAP object in Hello messages from the neighbor.ro Integer32 .1.3.6.1.4.1.6141.2.60.30.1.1.17 |
wwpLeosRsvpte OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.60.30.1.2 |
wwpLeosRsvpteIfTableA table of interfaces that RSVP-TE can be enabled on. SEQUENCE OF WwpLeosRsvpteIfEntry .1.3.6.1.4.1.6141.2.60.30.1.2.1 |
wwpLeosRsvpteIfEntryWWP Descr. WwpLeosRsvpteIfEntry .1.3.6.1.4.1.6141.2.60.30.1.2.1.1 |
wwpLeosRsvpteIfNameInterface Namero DisplayString .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.1 |
wwpLeosRsvpteIfIndexInterface Index INTEGER .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.2 |
wwpLeosRsvpteIfIpAddrInterface IP Addressro IpAddress .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.3 |
wwpLeosRsvpteIfMtuRSVP-TE Interface MTUrw INTEGER .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.4 |
wwpLeosRsvpteIfAdminStatusDesired RSVP-TE status on this Interfacerw Enumeration .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.5 |
wwpLeosRsvpteIfOperStatusRSVP-TE Operational Status on this Interfacero Enumeration .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.6 |
wwpLeosRsvpteIfHelloIntervalRSVP-TE hello message interval.rw Unsigned32 .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.7 |
wwpLeosRsvpteIfHelloToleranceRSVP-TE hello tolerance defines number of hello interval which may pass without receiving a successful Hello message from a partner before the Hello session times out.rw Unsigned32 .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.8 |
wwpLeosRsvpteIfAdvertisedLabelThis attribute decides what kind of a Label will be advertised by RSVP-TE for a Label Request received on this L3 Interfacerw AdvertisedLabel .1.3.6.1.4.1.6141.2.60.30.1.2.1.1.9 |