WWP-IGMP-SNOOP-MIB
This MIB specifies the managed objects for IGMP Snooping specific to the WWP products.
Main OID:
wwpIgmpSnoopMIB.1.3.6.1.4.1.6141.2.10
27
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
27 total| Object Name |
|---|
wwpIgmpSnoopMIBThis MIB specifies the managed objects for IGMP Snooping specific to the WWP products. MODULE-IDENTITY .1.3.6.1.4.1.6141.2.10 |
wwpIgmpSnoopMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.10.1 |
wwpIgmpSnoop OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.10.1.1 |
wwpIgmpSnoopActivateActivate the Igmp Snooping operation with a value of True(1) or stop it with False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6141.2.10.1.1.1 |
wwpIgmpSnoopTableThe (conceptual) table listing the IP multicast groups for which there are members on particular vlans. SEQUENCE OF WwpIgmpSnoopEntry .1.3.6.1.4.1.6141.2.10.1.1.2 |
wwpIgmpSnoopEntryAn entry (conceptual row) in the wwpIgmpSnoopTable. WwpIgmpSnoopEntry .1.3.6.1.4.1.6141.2.10.1.1.2.1 |
wwpIgmpSnoopVlanIdThe vlan for which this entry contains information for an IP multicast group address.ro VlanId .1.3.6.1.4.1.6141.2.10.1.1.2.1.1 |
wwpIgmpSnoopGroupAddressThe IP multicast group address for which this entry contains information.ro IpAddress .1.3.6.1.4.1.6141.2.10.1.1.2.1.2 |
wwpIgmpSnoopActivePortsThe Port Map of the active ports for the igmp filter indexed by wwpIgmpSnoopVlanId and wwpIgmpSnoopGroupAddress.ro PortList .1.3.6.1.4.1.6141.2.10.1.1.2.1.3 |
wwpIgmpSnoopRouterPortThe router port from which the igmp query messages are received, and joins/leaves messages are sent.ro Integer32 .1.3.6.1.4.1.6141.2.10.1.1.2.1.4 |
wwpIgmpSnoopQueryTimeThe time at which the last activity was observed on this stream.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6141.2.10.1.1.2.1.5 |
wwpIgmpSnoopLingerTimeoutThis value specifies the amount of time that a multicast filter will be in place after the last host has left. In essence it configures how long to filter the stream after all the hosts have left the group. This can tune the system as to how long the router has to remove the stream from the subnet. The minimum value is 1 second, with no maximum value.rw Integer32 .1.3.6.1.4.1.6141.2.10.1.1.3 |
wwpIgmpSnoopExpiryTimeoutThe interval of time for which an igmp protocol entry, is allowed to remain valid without any activity.rw Integer32 .1.3.6.1.4.1.6141.2.10.1.1.4 |
wwpIgmpSnoopQueryMessagesThe total number of query messages snooped.ro Counter32 .1.3.6.1.4.1.6141.2.10.1.1.5 |
wwpIgmpSnoopJoinMessagesThe total number of Join messages snooped.ro Counter32 .1.3.6.1.4.1.6141.2.10.1.1.6 |
wwpIgmpSnoopLeaveMessagesThe total number of leave messages snooped.ro Counter32 .1.3.6.1.4.1.6141.2.10.1.1.7 |
wwpIgmpSnoopRouterDiscardsThe total number of messages discarded by the Router.ro Counter32 .1.3.6.1.4.1.6141.2.10.1.1.8 |
wwpIgmpSnoopMinQueryTimeoutThe minimum interval of time for which an igmp protocol entry, is allowed to wait for any igmp query.rw Integer32 .1.3.6.1.4.1.6141.2.10.1.1.9 |
wwpIgmpSnoopLeaveModeSetting the igmp leave mode to 'fast(1)' will cause the multicast stream to be pruned as soon as a leave is received. If this object is set to 'inquisitive(2)', then a Group Specific Query is created for the multicast stream for which the leave was received. If no membership report is received in the time interval configured by the wwpIgmpSnoopInqLeaveTimeout, then the multicast stream is pruned.rw Enumeration .1.3.6.1.4.1.6141.2.10.1.1.10 |
wwpIgmpSnoopInqLeaveTimeoutThe interval of time in units of 0.1 ( tenth ) seconds for which the Group Specific Query, is allowed to wait for any response. The inquisitive leave timer is started only when the wwpIgmpSnoopLeaveMode is set to 'inquisitive(2)'.rw Integer32 .1.3.6.1.4.1.6141.2.10.1.1.11 |
wwpIgmpSnoopUnresMcastFilterAdminStatusThe desired state of the unsolicited (unresolved) multicast streams.rw Enumeration .1.3.6.1.4.1.6141.2.10.1.1.12 |
wwpIgmpSnoopUnresMcastFilterOperStatusThe current operational state of the unsolicited (unresolved) multicast streams. If this object value is 'enable', then unsolicited (unresolved) multicast streams will not be flooded to any port.ro Enumeration .1.3.6.1.4.1.6141.2.10.1.1.13 |
wwpIgmpSnoopMIBNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.10.2 |
wwpIgmpSnoopMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.10.2.0 |
wwpIgmpSnoopMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.10.3 |
wwpIgmpSnoopMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.10.3.1 |
wwpIgmpSnoopMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.10.3.2 |
More MIBs from World Wide Packets
Browse all World Wide PacketsMIBs →WWP-ESM-MIB
SNMP MIB module
454 objects→
WWP-LEOS-CFM-MIB
The WWP-LEOS-CFM-MIB enables configuration and monitoring of IEEE 802.1ag Connectivity Fault Management (CFM) entities, including Maintenance Domains, Maintenance Associations, and Maintenance End Points, on WWP-LEOS network devices. It facilitates the retrieval of critical fault detection metrics such as Continuity Check (CC) state, Last Link Status, and Maintenance Level (ML) to verify Layer 2 connectivity integrity.
443 objects→
WWP-LEOS-VPLS-MIB
SNMP MIB module
308 objects→
WWP-LEOS-FLOW-MIB
SNMP MIB module
307 objects→
WWP-LEOS-PORT-STATS-MIB
The WWP-LEOS-PORT-STATS-MIB module monitors Layer 2 Ethernet port statistics on WWP (Wireless WAN Platform) devices running LEOS firmware, specifically tracking interface counters such as octets, packets, errors, and discards for operational visibility and fault detection.
253 objects→
WWP-LEOS-CHASSIS-MIB
The WWP-LEOS-CHASSIS-MIB facilitates the retrieval of the specific system part number and serial number for WWP LEOS chassis hardware via SNMP. These object identifiers enable precise asset inventory tracking and device identification within network management systems.
233 objects→