WWP-EXT-BRIDGE-MIB
Updated with port rate limit state and rate limit value controls.
Main OID:
wwpExtBridgeMIB.1.3.6.1.4.1.6141.2.4
46
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
46 total| Object Name |
|---|
wwpExtBridgeMIBUpdated with port rate limit state and rate limit value controls. MODULE-IDENTITY .1.3.6.1.4.1.6141.2.4 |
wwpExtBridgeMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.1 |
wwpPort OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.1.1 |
wwpPortTableTable of Ports. SEQUENCE OF WwpPortEntry .1.3.6.1.4.1.6141.2.4.1.1.1 |
wwpPortEntryPort Entry in the Table. WwpPortEntry .1.3.6.1.4.1.6141.2.4.1.1.1.1 |
wwpPortIdPort ID for the instance. Port ID's start at 1, and are consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.ro INTEGER .1.3.6.1.4.1.6141.2.4.1.1.1.1.1 |
wwpPortTypeThe port type for the port.ro Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.2 |
wwpPortNameFriendly name for the port.rw DisplayString .1.3.6.1.4.1.6141.2.4.1.1.1.1.3 |
wwpPortPhysAddrThe ethernet MAC address for the port. This information can also be achieved via dot1dTpFdbTablero MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6141.2.4.1.1.1.1.4 |
wwpPortAutoNegThe object sets the port to AUTO NEG MOde and vice versa. Specific platforms may have requirements of configuring speed before moving the port to out of AUTO-NEG mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6141.2.4.1.1.1.1.5 |
wwpPortAdminStatusThe desired state of the port.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.6 |
wwpPortOperStatusThe current operational state of Port.ro Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.7 |
wwpPortAdminSpeedDesired speed of the port. Set the port speed to be either 10MB, 100MB, or gig. The Management Station can't set the adminSpeed to auto. The default value for this object depends upon the platform.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.8 |
wwpPortOperSpeedThe current operational speed of the port in MB.ro Integer32 .1.3.6.1.4.1.6141.2.4.1.1.1.1.9 |
wwpPortAdminDuplexThe desired mode for the port. It can be set to either half or full duplex operation but not to auto.The default value for this object depends upon the platform.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.10 |
wwpPortOperDuplexThe current duplex mode of the port.ro Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.11 |
wwpPortAdminFlowCtrlConfigures the ports flow control operation. Need to check 802.3x for additional modes for gig ports.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.12 |
wwpPortOperFlowCtrlShows ports flow control configuration.ro Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.13 |
wwpPortTaggedThe port tagged Status can be set to tagged or untagged. If a port is part of more than one VLAN, then the port Status should be 'tagged'.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.14 |
wwpPortUntaggedPriorityThe 802.1p packet priority to be assigned to packets associated with this port that do not have an 802.1Q VLAN header.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.15 |
wwpPortMaxFrameSizeSetting this object will set the max frame size allowed on a port. The max frame size can vary between 1522 bytes till 9216 bytes. Default value is 1522 bytesrw INTEGER .1.3.6.1.4.1.6141.2.4.1.1.1.1.16 |
wwpPortIngressFilteringWhen this is true(1) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When false(2), the port will accept all incoming frames.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.1.1.1.17 |
wwpPortRateLimitStateWhen set to true, the rate limiting mechanism is enabled for this port. When set to false, the rate limiting mechanism is disabled for this port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6141.2.4.1.1.1.1.18 |
wwpPortRateLimitValueThe value of this object represents the desired bit-rate limit for this port. When the rate limiting mechanism is enabled for this port, this value is enforced to the best extent possible by the device. For some devices the actual maximum bit-rate allowed may exceed the rate limit parameter under certain circumstances due to hardware and software limitations.rw INTEGER .1.3.6.1.4.1.6141.2.4.1.1.1.1.19 |
wwpLocalMgmtPortEnableSetting this object to false(2) will disable the local Management Port. The object has beed deprecated as we need to have the general functionality of disabling and enableing any in-band and out-band mgmt interface.rwdeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6141.2.4.1.1.2 |
wwpVlan OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.1.2 |
wwpVlanVersionNumberThe version number of IEEE 802.1Q that this device supports.ro Enumeration .1.3.6.1.4.1.6141.2.4.1.2.1 |
wwpMaxVlanIdThe maximum IEEE 802.1Q VLAN ID that this device supports.ro VlanId .1.3.6.1.4.1.6141.2.4.1.2.2 |
wwpMaxSupportedVlansThe maximum number of IEEE 802.1Q VLANs that this device supports.ro Unsigned32 .1.3.6.1.4.1.6141.2.4.1.2.3 |
wwpNumVlansThe current number of IEEE 802.1Q VLANs that are configured in this device.ro Unsigned32 .1.3.6.1.4.1.6141.2.4.1.2.4 |
wwpVlanTableVLAN table SEQUENCE OF WwpVlanEntry .1.3.6.1.4.1.6141.2.4.1.2.5 |
wwpVlanEntrytable of vlans WwpVlanEntry .1.3.6.1.4.1.6141.2.4.1.2.5.1 |
wwpVlanId802.1Q VLAN ID (1-4094)ro VlanId .1.3.6.1.4.1.6141.2.4.1.2.5.1.1 |
wwpVlanNameName associated with this VLAN.rw DisplayString .1.3.6.1.4.1.6141.2.4.1.2.5.1.2 |
wwpVlanCurrentEgressPortsThe set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames.rw PortList .1.3.6.1.4.1.6141.2.4.1.2.5.1.3 |
wwpVlanCurrentUntaggedPortsThe set of ports which are transmitting traffic for this VLAN as untagged frames.ro PortList .1.3.6.1.4.1.6141.2.4.1.2.5.1.4 |
wwpVlanMgmtStatusIndicates if this VLAN is a management VLAN. The system can have at most one remote mgt vlan, and one local mgt vlan. Any Valn can be set either to remoteMgmtVlan or localMgmtvlan.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.2.5.1.5 |
wwpVlanRowStatusUsed to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, there should not be any port associated with this vlan.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6141.2.4.1.2.5.1.6 |
wwpVlanXTableExtension of the VLAN table SEQUENCE OF WwpVlanXEntry .1.3.6.1.4.1.6141.2.4.1.2.6 |
wwpVlanXEntryEntry in the extended vlan table. WwpVlanXEntry .1.3.6.1.4.1.6141.2.4.1.2.6.1 |
wwpVlanTunnelEnable/disable VLAN tunneling on this VLAN.rw Enumeration .1.3.6.1.4.1.6141.2.4.1.2.6.1.1 |
wwpExtBridgeMIBNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.2 |
wwpExtBridgeMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.2.0 |
wwpExtBridgeMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.3 |
wwpExtBridgeMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.3.1 |
wwpExtBridgeMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6141.2.4.3.2 |