WESTERMO-WEOS-MIB
AI MIB Summary
The WESTERMO-WEOS-MIB module enables SNMP-based monitoring and management of Westermo industrial routers and switches running the WeOS operating system, providing access to device-specific operational parameters, interface statistics, and system health metrics.
This MIB module controls the SNMP functionality in the WeOS branch of the Westermo private MIB.
Main OID:
weos.1.3.6.1.4.1.2544.2.1
260
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
260 total| Object Name |
|---|
weosThis MIB module controls the SNMP functionality in the WeOS
branch of the Westermo private MIB. MODULE-IDENTITY .1.3.6.1.4.1.2544.2.1 |
command OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.1 |
rebootWriting value '1' will reboot the unit.
(The unit will boot up using the startup configuration)
Reading the reboot object will return '0' (zero)rw Enumeration .1.3.6.1.4.1.2544.2.1.1.1 |
factoryResetWriting value '1' will reset unit configuration to
factory default values and reboot.
Reading the factoryReset object will return '0' (zero)rw Enumeration .1.3.6.1.4.1.2544.2.1.1.2 |
phy OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.2 |
lffTableTable containing Westermo Link Fail Forward (LFF) settings and status
applicable ports.
Westermo LFF is used to indicate the state (up/down) of a remote link.
The currently supported use case is when extending an Ethernet over an SHDSL link.
LFF is used to inform the local end that the Ethernet link at the remote site is
up or down. SEQUENCE OF LffEntry .1.3.6.1.4.1.2544.2.1.2.1 |
lffEntryFor each local (SHDSL) port, there is a row in the lffTable containing
LFF status and settings. LffEntry .1.3.6.1.4.1.2544.2.1.2.1.1 |
lffPortIfIndexThis index should map to the local (SHDSL) port's ifIndex in the ifTable.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.2.1.1.1 |
lffPortIfNameThis name should map to the local (SHDSL) port's ifName in the ifXTable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.2.1.1.2 |
lffStatusThe lffStatus shows the status of a (Ethernet) link at the remote end of a SHDSL link:
- 1 (disabled): LFF is configured 'disabled' on local (SHDSL) port.
- 2 (unknown): LFF enabled, but the state of remote (Ethernet)
is unknown. (perhaps because the intermediate
(SHDSL) link is down).
- 3 (remoteDown): LFF enabled, remote (Ethernet) port down
- 4 (remoteUp): LFF enabled, remote (Ethernet) port up.ro Enumeration .1.3.6.1.4.1.2544.2.1.2.1.1.3 |
sfp OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.2.2 |
sfpDdmPortTableTable containing DDM diagnostics per DDM capable SFP. SEQUENCE OF SfpDdmPortEntry .1.3.6.1.4.1.2544.2.1.2.2.1 |
sfpDdmPortEntryThis row in the sfpDdmPortTable containing per port
SFP DDM diagnostics. SfpDdmPortEntry .1.3.6.1.4.1.2544.2.1.2.2.1.1 |
sfpDdmPortIfIndexThis index maps to the port's ifIndex in the ifTable.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.2.2.1.1.1 |
sfpDdmPortIfNameThe system name of the port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.2.2.1.1.2 |
sfpDdmPortVoltageThe supply voltage of the SFP. The accuracy is better than +/-3 %
and the total range of 0 - 6550 mV. The voltage is represented in mV.ro Integer32 .1.3.6.1.4.1.2544.2.1.2.2.1.1.3 |
sfpDdmPortTemperatureTemperature of the SFP. The temperature accuracy is better than 3 degrees Celsius
and the total range of -128 degrees C to +128 degrees C.ro Integer32 (-128..128) .1.3.6.1.4.1.2544.2.1.2.2.1.1.4 |
sfpDdmPortBiasCurrentThe transmitt bias current. The accuracy is better than +/- 10 %
and the total range of 0 - 131 mA. The current is represented in uA.ro Integer32 .1.3.6.1.4.1.2544.2.1.2.2.1.1.5 |
sfpDdmPortTxPowerTransmitt power of the laser. The accuracy is better than +/-3dB and
the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented
in steps of 0.01 dBmro Integer32 (-4000..820) .1.3.6.1.4.1.2544.2.1.2.2.1.1.6 |
sfpDdmPortRxPowerReceiving power of the laser. The accuracy is better than +/-3dB and
the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented
in steps of 0.01 dBmro Integer32 (-4000..820) .1.3.6.1.4.1.2544.2.1.2.2.1.1.7 |
phyStats OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.2.3 |
summaryFCSErrorsThe summaryFCSErrors display the total of FCS errors for
all ports on the unitro Integer32 .1.3.6.1.4.1.2544.2.1.2.3.1 |
bwStatsTableTable containing port bandwidth rates. SEQUENCE OF BwStatsEntry .1.3.6.1.4.1.2544.2.1.2.3.2 |
bwStatsEntryFor each local port, there is a row in the bwStatsTable containing
port bandwidth rates. BwStatsEntry .1.3.6.1.4.1.2544.2.1.2.3.2.1 |
bwStatsIndexThe value of this object uniquely identifies this bwStats entry.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.2.3.2.1.1 |
bwStatsEnabledBandwidth statistics enabled or disabled for this port.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.2.3.2.1.2 |
bwStatsBitrateIn10sThe current average input traffic for the last 10 seconds.
This value is calculated via periodic sampling of the port counters
And will be updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.3 |
bwStatsBitrateOut10sThe current average output traffic for the last 10 seconds.
This value is calculated via periodic sampling of the port counters
And will be updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.4 |
bwStatsBitrateIn1mThe current moving average input traffic for the last minute.
This value is calculated and updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.5 |
bwStatsBitrateOut1mThe current moving average output traffic for the last minute.
This value is calculated and updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.6 |
bwStatsBitrateIn10mThe current moving average input traffic for the last 10 minutes.
This value is calculated and updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.7 |
bwStatsBitrateOut10mThe current moving average output traffic for the last 10 minutes.
This value is calculated and updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.8 |
bwStatsBitrateIn1hThe current moving average input traffic for the last hour.
This value is calculated and updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.9 |
bwStatsBitrateOut1hThe current moving average output traffic for the last hour.
This value is calculated and updated at least every 10 seconds.
The unit is bits per second and this includes Ethernet
header data (Ethernet preamble not included).ro Counter64 UNITS "Bits per second" .1.3.6.1.4.1.2544.2.1.2.3.2.1.10 |
link OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3 |
vlan OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3.1 |
l2Qos OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3.2 |
l2QosVlanTableTable containing VLAN priority settings for
existing VLANs. SEQUENCE OF L2QosVlanEntry .1.3.6.1.4.1.2544.2.1.3.2.1 |
l2QosVlanEntryThe row in the l2QosVlanTable containing per VLAN
priority settings. L2QosVlanEntry .1.3.6.1.4.1.2544.2.1.3.2.1.1 |
l2QosVlanIdThis index should be mapped to the VLAN ID of Q-bridge MIB.ro VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.2544.2.1.3.2.1.1.1 |
vlanPriorityEnabledEnable (true) or disable (false) VLAN priority for this VLAN.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.2.1.1.2 |
vlanPriorityLevelThe VLAN priority level for this VLAN.
0 is lowest and 7 is highest priority.rw Integer32 .1.3.6.1.4.1.2544.2.1.3.2.1.1.3 |
l2QosPortTableTable containing per port piority settings for LAN ports SEQUENCE OF L2QosPortEntry .1.3.6.1.4.1.2544.2.1.3.2.2 |
l2QosPortEntryThe row in the l2QosPortTable containing per port
priority settings. L2QosPortEntry .1.3.6.1.4.1.2544.2.1.3.2.2.1 |
l2QosPortIfIndexThis index should map to the port's ifIndex in the ifTable.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.3.2.2.1.1 |
l2QosPortIfNameThis name should map to the port's ifName in the ifXTable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.2.2.1.2 |
l2QosPortPriorityModeThe priority mode (tag, ip or port) to be used on this specific port.
1. (tag): Use the incoming packet's VLAN tag priority value to determine
its priority. (Untagged packets will have their priority based on
the configured port priority.)
2. (ip): Use the incoming packet's IP ToS/DSCP priority value to determine
its priority. (Non-IP packets will have their priority based on
the configured port priority.)
3. (port): Use the ingress port's configured priority to determine the
packets priority.rw Enumeration .1.3.6.1.4.1.2544.2.1.3.2.2.1.3 |
l2QosPortPriorityLevelThe port priority level for this port. 0 is lowest and 7 is highest priority.rw Integer32 .1.3.6.1.4.1.2544.2.1.3.2.2.1.4 |
frnt OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3.3 |
frntv0 OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3.3.1 |
frntv0TableTable containing a list of FRNTv0 instances/rings. SEQUENCE OF Frntv0Entry .1.3.6.1.4.1.2544.2.1.3.3.1.1 |
frntv0EntryThe row in the frntv0Table containing settings and status information
for a specific FRNTv0 instance/ring. Frntv0Entry .1.3.6.1.4.1.2544.2.1.3.3.1.1.1 |
frntv0InstanceIdThe instance id of this FRNTv0 Ring
(only of local significance to this unit).ro Integer32 .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.1 |
frntv0FocalPointEnabledTrue(1) if this unit is configured as focal point for this FRNTv0 instance.
False(2) if this unit is configured as member switch for this FRNTv0 instance.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.2 |
frntv0Port1Name of FRNT port M in the FRNT port pair.
In case the unit is configured as focal point and the ring is fully connected,
it is port M that is put in BLOCKING.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.3 |
frntv0Port2Name of FRNT port N in the FRNT port pair. In case of an edge in a FRNT bus
rather than a node in a FRNT ring then port N shall be set to 'None' and it
will be read as 'None'. In case the unit is configured as focal point and
the ring is fully connected, it is port M that is put in BLOCKING.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.4 |
frntv0Port1StateProvides information about the status of FRNT port M.
See frntv0RingStatus for more details.ro Enumeration .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.5 |
frntv0Port2StateProvides information about the status of FRNT port N.
See frntv0RingStatus for more details.ro Enumeration .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.6 |
frntv0RingStatusRead ring status information. The answer is to be interpreted
differently when asking a focal point or a member switch.
Focal point (status of the whole FRNT topology):
1. ring mode: A focal point reports 'ring(1)' when the FRNT
topology is intact. On a focal point this indicates OK.
2. bus mode: A focal point reports 'bus(2)' when it has
detected an ERROR in the FRNT topology, i.e., the topology
is broken. It can either be an error on any of its local
FRNT ports (M or N), or elsewhere in the FRNT topology.
Member switch (status of the member's local FRNT ports):
1. ring mode: A member switch reports 'ring(1)' when
one or both of its FRNT ports are down or in blocking
state. On a member switch this indicates an ERROR.
2. bus mode: A member switch reports 'bus(2)' when both its
FRNT ports are in forwarding state. On a member switch this
is an indication of OK, but it only has significance for
this member switch, not the whole FRNT topology.ro Enumeration .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.7 |
frntv0RowStatusThis object indicates the status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.8 |
frntv0TopologyChangeCountThis object indicates the number of transitions between bus/ring mode
since FRNT was enabled.ro Integer32 .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.9 |
frntv0TopologyTimeSinceLastChangeThis object indicates the time that have passed since the last change of
ring status.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.10 |
frntv0PortsSwappedFRNT can detect if the FRNT ports have been swapped. For example if port1
is connected to port1 on another FRNT unit.
True(1) if the ports are swapped.
False(2) if the ports are not swapped.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.3.1.1.1.11 |
igmpSnooping OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3.4 |
igmpSnoopingQuerierModeThe querierMode object controls the querier mode an IGMP snooping
switch will operate in on IGMP Snooping enabled VLANs.
If the switch does not have an IP address on a certain VLAN,
the switch will act in proxy querier mode irrespective of the
querierMode setting.
1. Autonegotiate querier. The switch will become querier on a VLAN
unless it hears IGMP queries on that VLAN from device with
lower IP address.
2. Force querier role. The switch will act as querier on every VLAN
where IGMP snooping is enabled.
3. Operate in proxy querier mode.rw Enumeration .1.3.6.1.4.1.2544.2.1.3.4.1 |
igmpSnoopingQuerierIntervalThe IGMP Querier Interval (seconds). This interval will be used on all
interfaces where this unit acts as IGMP Querier, unless multicast routing
protocol specific or interface specific querier setting exist.
Currently, the following interval values are valid: 12, 30, 70 and 150 (seconds).rw Integer32 .1.3.6.1.4.1.2544.2.1.3.4.2 |
staticMulticastRouterPortsThis is a comma-separated list of (LAN)port names, which
specifies statically configured 'multicast router ports'. All
layer-2 multicast traffic (known and unknown) should be forwarded
onto multicast router ports.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.4.3 |
currentMulticastRouterPortsThis is a comma-separated list of portnames, which lists
all ports operating as multicast router ports - both dynamically
discovered (e.g., by reception of IGMP Queries) or statically
configured multicast router ports. All (layer-2) multicast traffic
(known and unknown) should be forwarded onto multicast router
ports.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.4.4 |
igmpSnoopingVlanTableA list of configuration entries for VLAN specific IGMP Snooping objects. SEQUENCE OF IgmpSnoopingVlanEntry .1.3.6.1.4.1.2544.2.1.3.4.5 |
igmpSnoopingVlanEntryAn IGMP Snooping VLAN entry contains IGMP Snooping objects relevant for
IGMP Snooping management per VLAN. IgmpSnoopingVlanEntry .1.3.6.1.4.1.2544.2.1.3.4.5.1 |
igmpSnoopingVlanIdThis index should match corresponding VLAN ID of Q-bridge MIB.ro VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.2544.2.1.3.4.5.1.1 |
igmpSnoopingEnabledIGMP Snooping enabled or disabled on this particular VLAN.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.4.5.1.2 |
rico OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3.5 |
riCoStatusTableTable containing status for a list of RiCo and/or Dual Homing
instances present on this unit. SEQUENCE OF RiCoStatusEntry .1.3.6.1.4.1.2544.2.1.3.5.1 |
riCoStatusEntryRow in the riCoStatusTable that is containing settings and
status information for a specific RiCo/Dual-Homing instance. RiCoStatusEntry .1.3.6.1.4.1.2544.2.1.3.5.1.1 |
riCoStatusRingIdxThe ring instance ID of this RiCo/Dual-Homing instance
(only of local significance to this unit).
- For RiCo instances, the ring ID corresponds to the
associated FRNT ring ID.
- For Dual Homing instances, the ring ID is always '0'.ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.1.1.1 |
riCoStatusCouplingIdxThe ID of this RiCo/Dual-Homing instance.
(only of local significance to this unit).
Unique per ring instance (riCoStatusRingIdx).ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.1.1.2 |
riCoStatusNodeIdThe unique ID of this RiCo node. A MAC address (typically the
base MAC address) of this unit.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.1.1.3 |
riCoStatusHelloIntervalConfigured RiCo Ring Hello interval in milliseconds.
Not applicable for Dual Homing instances (value '0')ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.1.1.4 |
riCoStatusHelloEffectiveEffective RiCo Ring Hello interval in milliseconds. Shows
negotiated Hello interval.
Not applicable for Dual Homing instances (value '0').ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.1.1.5 |
riCoStatusUplinkTableTable containing status of RiCo and Dual-Homing uplinks per link SEQUENCE OF RiCoStatusUplinkEntry .1.3.6.1.4.1.2544.2.1.3.5.2 |
riCoStatusUplinkEntryThe row in the riCoStatusUplinkTable containing status information
for a specific RiCo or Dual-Homing uplink. For RiCo, status
for all local uplinks, and for the best uplink of each RiCo
peer is listed. For dual-homing, status for all local
uplinks is listed. RiCoStatusUplinkEntry .1.3.6.1.4.1.2544.2.1.3.5.2.1 |
riCoStatusUplinkRingIdxThe ring instance ID of this RiCo/Dual-Homing instance
(only of local significance to this unit).
- For RiCo instances, the ring ID corresponds to the
associated FRNT ring ID.
- For Dual Homing instances, the ring ID is always '0'.ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.2.1.1 |
riCoStatusUplinkCouplingIdxThe instance id of this riCo Uplinkro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.2.1.2 |
riCoStatusUplinkNodeIdThe unique ID of the node, i.e., the MAC address of the
node. For RiCo, this can be the (base) MAC of the local unit,
or the MAC identifying a peer RiCo node. For
Dual-Homing, this is the (base) MAC of the local unit.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.2.1.3 |
riCoStatusUplinkIfIndexThe interface index of the uplink port.
- For local uplinks, this index corresponds to the port's
index in the ifTable (IF-MIB).
- For non-local uplinks, the value is not valid (value '0').ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.3.5.2.1.4 |
riCoStatusUplinkStatusUplink active (1), backup (2) or down (3).ro Enumeration .1.3.6.1.4.1.2544.2.1.3.5.2.1.5 |
riCoStatusUplinkIfNameThe name of the interface used for this uplink.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.2.1.6 |
riCoStatusUplinkPrioEffective priority of this uplink. Based on configured
priority and 'adjust' value (sticky uplink).ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.2.1.7 |
riCoStatusUplinkPathCostCurrent path cost for this uplink.ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.2.1.8 |
riCoStatusUplinkHelloIntervalConfigured Ring Hello Interval for the RiCo node of this
uplink. Not valid for Dual-Homing, value '0')ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.2.1.9 |
riCoStatusUplinkHelloIntervalEffectiveEffective Ring Hello Interval for the RiCo node of this
uplink. Not valid for Dual-Homing, value '0')ro Integer32 .1.3.6.1.4.1.2544.2.1.3.5.2.1.10 |
riCoStatusUplinkChangedCounterNumber of times this uplink changed its statero Integer32 .1.3.6.1.4.1.2544.2.1.3.5.2.1.11 |
riCoStatusUplinkSynchronizedSynchronization status for this uplink:
- synchronized(1): Synchronize enabled and ok
- notSynchronized(2): Synchronize enabled and fails
- notApplicable(3): Non-local RiCo uplink, or Dual-Homing
uplink where Synchronize is disabledro Enumeration .1.3.6.1.4.1.2544.2.1.3.5.2.1.12 |
riCoStatusUplinkPreferredPreferred uplink status.
Only valid for Dual-Homing uplinks whit synchronization enabled.
- preferred(1): Dual-Homing uplink has status 'Preferred'
- notPreferred(2): Dual-Homing uplink has status 'Not Preferred'
- notApplicable(3): Uplink is either
- a Dual-Homing uplink with synchronization disabled, or
- a RiCo uplink (local or non-local)ro Enumeration .1.3.6.1.4.1.2544.2.1.3.5.2.1.13 |
riCoStatusUplinkLocalLocal(true) or global(false) instancero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.2.1.14 |
riCoCfgTableTable containing a list of RiCo couplings. SEQUENCE OF RiCoCfgEntry .1.3.6.1.4.1.2544.2.1.3.5.3 |
riCoCfgEntryThe row in the riCoTable containing settings for a specific
RiCo or Dual-Homing instance. RiCoCfgEntry .1.3.6.1.4.1.2544.2.1.3.5.3.1 |
riCoCfgRingIdxThe ring instance ID of this RiCo/Dual-Homing instance
(only of local significance to this unit).
- For RiCo instances, the ring ID corresponds to the
associated FRNT ring ID.
- For Dual Homing instances, the ring ID is always '0'.rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.3.1.1 |
riCoCfgCouplingIdxThe ID of this RiCo/Dual-Homing instance.
(only of local significance to this unit).
Unique per ring instance (riCoCfgRingIdx).rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.3.1.2 |
riCoCfgEnabledEnable or disable the RiCo instance
True (1) or False (2)rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.3.1.3 |
riCoCfgHelloIntervalConfigured RiCo Ring Hello interval in milliseconds.
- Default: 100 milliseconds
- Configurable in range: 50-1000 milliseconds
- Not applicable for Dual Homing instances (value '0')rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.3.1.4 |
riCoCfgSynchronizeEnable/disable Uplink synchronization. 'True' to enable,
and 'False' to disable synchronization.
Note: Only configurable for Dual-Homing Uplinks. For RiCo
Uplinks, synchronization is always enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.3.1.5 |
riCoCfgRowStatusThis object indicates the status of this table entry.
This object can also be used to create or delete instances.
At most 1 RiCo instance and at most 8 Dual-Homing instances
can be created.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.3.1.6 |
riCoCfgUplinkTableTable containing RiCo and Dual-Homing uplinks and
corresponding settings per link. SEQUENCE OF RiCoCfgUplinkEntry .1.3.6.1.4.1.2544.2.1.3.5.4 |
riCoCfgUplinkEntryThe row in the riCoLinkTable containing settings and status information
for a specific RiCo or Dual-Homing Uplink. RiCoCfgUplinkEntry .1.3.6.1.4.1.2544.2.1.3.5.4.1 |
riCoCfgUplinkRingIdxThe ring instance ID of this RiCo/Dual-Homing instance
(only of local significance to this unit).
- For RiCo instances, the ring ID corresponds to the associated FRNT ring ID.
- For Dual Homing instances, the ring ID is always '0'.rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.4.1.1 |
riCoCfgUplinkCouplingIdxThe ID of this RiCo/Dual-Homing instance.
(only of local significance to this unit).
Unique per ring instance (riCoStatusRingIdx).rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.4.1.2 |
riCoCfgUplinkIfIndexThe interface index of the uplink port.
For local uplinks, this index corresponds to the port's
index in the ifTable (IF-MIB).rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.3.5.4.1.3 |
riCoCfgUplinkPrioConfigure priority for this uplink (128 as default).
A lower value increases the chance to be elected as active
uplink.rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.4.1.4 |
riCoCfgUplinkAdjustConfigure adjust value for this uplink (sticky uplink).
The effictive priority is reduced by the adjust value if the
link becomes elected as active uplink. Default '0'.rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.4.1.5 |
riCoCfgUplinkEchoTimeUplink echo interval to be set for this uplink in
milliseconds. Default: 200 ms Range: 20-1000 msrw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.4.1.6 |
riCoCfgUplinkPathCostPath-cost to be set for this uplink. '0' means 'Auto', which
lets path cost depend on speed and duplex of the uplink.rw Integer32 .1.3.6.1.4.1.2544.2.1.3.5.4.1.7 |
riCoCfgUplinkRowStatusThis object indicates the status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.5.4.1.8 |
lldpCtlv OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.3.6 |
lldpCtlvTableThe LLDP custom TLV (Type 127) configuration table SEQUENCE OF LldpCtlvEntry .1.3.6.1.4.1.2544.2.1.3.6.1 |
lldpCtlvEntryA custom TLV entry. LldpCtlvEntry .1.3.6.1.4.1.2544.2.1.3.6.1.1 |
lldpCtlvIdxIndex of this custom TLV. Only of local significance.ro INTEGER .1.3.6.1.4.1.2544.2.1.3.6.1.1.1 |
lldpCtlvOuiOrganizationally unique identifier (OUI), 3 hex-encoded
bytes. Required.rw OCTET STRING .1.3.6.1.4.1.2544.2.1.3.6.1.1.2 |
lldpCtlvSubTypeOrganizationally defined subtype, one byte. Default: 0rw INTEGER .1.3.6.1.4.1.2544.2.1.3.6.1.1.3 |
lldpCtlvInfoInformation/value part of custom TLV. 0-507 octets encoded as
hex. Default: Emptyrw OCTET STRING .1.3.6.1.4.1.2544.2.1.3.6.1.1.4 |
lldpCtlvRowStatusThis object indicates the status of this table entry. Used to
create or delete a custom TLV entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.6.1.1.5 |
lldpCtlvPortTableTable specifying which custom TLV(s) to transmit per
port. Each row in the table maps a custom TLV to a port. Each
custom TLV in the lldpCtlvTable can be mapped to one or more
ports. SEQUENCE OF LldpCtlvPortEntry .1.3.6.1.4.1.2544.2.1.3.6.2 |
lldpCtlvPortEntryEach entry maps a custom TLV to a port. LldpCtlvPortEntry .1.3.6.1.4.1.2544.2.1.3.6.2.1 |
lldpCtlvPortIdxThe logical number of the port. This is the same
number as the dot1dBasePort (dot1dBasePortTable of BRIDGE-MIB) for
this port. INTEGER .1.3.6.1.4.1.2544.2.1.3.6.2.1.1 |
lldpCtlvPortCtlvIdxCustom TLV index (lldpCtlvTable) INTEGER .1.3.6.1.4.1.2544.2.1.3.6.2.1.2 |
lldpCtlvPortRowStatusThis object indicates the status of this table entry. Used to
create or delete a 'custom TLV to port' mapping.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.6.2.1.3 |
lldpRemCtlvTableTable listing all custom TLV(s) received. Each entry
represents a custom TLV received on a specific port from
individual neighbours. Entries are
removed when the TTL of the LLDP message expires, and will be
removed/replaced when a new LLDP message from the same neighbour
is received. SEQUENCE OF LldpRemCtlvEntry .1.3.6.1.4.1.2544.2.1.3.6.3 |
lldpRemCtlvEntryCustom TLV received on a port. LldpRemCtlvEntry .1.3.6.1.4.1.2544.2.1.3.6.3.1 |
lldpRemCtlvLocalPortThe logical number of the local port receiving this
custom TLV. This is the same number as the dot1dBasePort
(dot1dBasePortTable of BRIDGE-MIB) for this port.ro INTEGER .1.3.6.1.4.1.2544.2.1.3.6.3.1.1 |
lldpRemCtlvMacAddressThe MAC address of the neighbour node sending this
custom TLV.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.3.6.3.1.2 |
lldpRemCtlvOuiOrganizationally unique identifier (OUI), 3 hex-encoded bytes.ro OCTET STRING .1.3.6.1.4.1.2544.2.1.3.6.3.1.3 |
lldpRemCtlvSubTypeOrganizationally defined subtype, one byte.ro INTEGER .1.3.6.1.4.1.2544.2.1.3.6.3.1.4 |
lldpRemCtlvInfoInformation/value part of custom TLV. 0-507 octets encoded as hex.ro OCTET STRING .1.3.6.1.4.1.2544.2.1.3.6.3.1.5 |
net OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.4 |
iface OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.4.1 |
ifaceCommon OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.4.1.1 |
ifaceInet4 OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.4.1.2 |
inet4StaticDefaultGatewayAddressIP Address of statically configured default gateway.
Setting the address to 0.0.0.0 means that there is 'no static
default gateway' configured.rw IpAddress .1.3.6.1.4.1.2544.2.1.4.1.2.1 |
inet4BaseIfaceTableTable containing base IPv4 settings per interface SEQUENCE OF Inet4BaseIfaceEntry .1.3.6.1.4.1.2544.2.1.4.1.2.2 |
inet4BaseIfaceEntryEntry in ipv4Interface table. Each row holds IPv4 settings
specific to this interface. Inet4BaseIfaceEntry .1.3.6.1.4.1.2544.2.1.4.1.2.2.1 |
inet4BaseIfIndexUniquely identifies an interface; same interface as identied by the
same value of ifIndex in the interfaces group.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.4.1.2.2.1.1 |
inet4BaseIfNameThe name matches the corresponding ifName in the ifXTable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.1.2.2.1.2 |
inet4BaseAddressModeThe IPv4 address assignment mode.rw Enumeration .1.3.6.1.4.1.2544.2.1.4.1.2.2.1.3 |
inet4StaticTableTable containing settings for static IPv4 interfaces SEQUENCE OF Inet4StaticEntry .1.3.6.1.4.1.2544.2.1.4.1.2.3 |
inet4StaticEntryEntry in ipv4Interface table. Each row holds IPv4 settings specific
to this interface. Inet4StaticEntry .1.3.6.1.4.1.2544.2.1.4.1.2.3.1 |
inet4StatIfIndexUniquely identifies an interface; same interface as identied by the same
value of ifIndex in the interfaces group.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.4.1.2.3.1.1 |
inet4StatIfNameThe name matches the corresponding ifName in the ifXTable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.1.2.3.1.2 |
inet4StatAddressStatically configured IPv4 address for this interface.
Address 0.0.0.0 means that the interface is disabled.rw IpAddress .1.3.6.1.4.1.2544.2.1.4.1.2.3.1.3 |
inet4StatNetmaskNetmask of statically assigned IP address.rw IpAddress .1.3.6.1.4.1.2544.2.1.4.1.2.3.1.4 |
inet4DhcpTableTable containing settings for IPv4 interfaces using DHCP for
address assignment SEQUENCE OF Inet4DhcpEntry .1.3.6.1.4.1.2544.2.1.4.1.2.4 |
inet4DhcpEntryEntry in inet4Dhcp table. Each row holds DHCP settings specific
to this interface. Inet4DhcpEntry .1.3.6.1.4.1.2544.2.1.4.1.2.4.1 |
inet4DhcpIfIndexUniquely identifies an interface; same interface as identied by the
same value of ifIndex in the interfaces group.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.4.1.2.4.1.1 |
inet4DhcpIfNameThe name matches the corresponding ifName in the ifXTable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.1.2.4.1.2 |
inet4DhcpClientIdClient ID passed by DHCP client to DHCP server.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.1.2.4.1.3 |
addressConflict OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.4.1.4 |
addressConflictExistsTrue if there are any conflicts detected, False if there are no more conflicts detected.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.1.4.1 |
addressConflictTableA list containing all IP and MAC address conflicts currently
on the this device SEQUENCE OF AddressConflictEntry .1.3.6.1.4.1.2544.2.1.4.1.4.2 |
addressConflictEntryAn entry containing details for the conflict AddressConflictEntry .1.3.6.1.4.1.2544.2.1.4.1.4.2.1 |
addressConflictIndexA unique value for each conflict.ro Integer32 .1.3.6.1.4.1.2544.2.1.4.1.4.2.1.1 |
addressConflictIfIndexIndex of the interface on this device.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.2.1.4.1.4.2.1.2 |
addressConflictIfNameName of the interface on this device.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.1.4.2.1.3 |
addressConflictTypeType of conflict:
1 : IP,
2 : MAC,
3 : IP & MACro Enumeration .1.3.6.1.4.1.2544.2.1.4.1.4.2.1.4 |
addressConflictMacAddressThe MAC address of the conflicting peer.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.1.4.2.1.5 |
addressConflictIPv4AddressThe IPv4 address of the conflicting peer.ro IpAddress .1.3.6.1.4.1.2544.2.1.4.1.4.2.1.6 |
addressConflictTimeTime (in seconds) elapsed since conflict was last detected.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.2544.2.1.4.1.4.2.1.7 |
ttdp OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.4.2 |
etbnInhibitionEnabledETBN inhibition enabled or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.4.2.1 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5 |
services OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.1 |
snmp OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.1.1 |
trapCommunityThe trap community name which traps destined to defined
traphost(s) are sent with.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.1.1 |
trapHostTableA list of SNMP trap host. SEQUENCE OF TrapHostEntry .1.3.6.1.4.1.2544.2.1.5.1.1.2 |
trapHostEntryAn entry containing information about a specific SNMP trap host. TrapHostEntry .1.3.6.1.4.1.2544.2.1.5.1.1.2.1 |
trapHostIdThe id of this SNMP Trap Host
(only of local significance to this unit).ro Integer32 .1.3.6.1.4.1.2544.2.1.5.1.1.2.1.1 |
trapHostAddressTypeThe type of Internet address by which the trap host
is reachable.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.2544.2.1.5.1.1.2.1.2 |
trapHostAddressThe IP address or Domain name for the trap host.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.1.2.1.3 |
trapHostRowStatusThis object indicates the status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.1.2.1.4 |
roCommunityThe read-only community name used to by SNMPv1/v2 to read
SNMP MIB parameters. The string 'Disabled' have a special
meaning and cannot be used as roCommunity string.
Reading:
String 'Disabled' - The read-only community is disabled
Otherwise the received string shows the current read-only community.
Writing:
String 'Disabled' - Disable the read-write community
Otherwise the written string becomes the new read-only community.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.1.3 |
rwCommunityProvides a mechanism to change or enable/disable the
read-write community name used to by SNMPv1/v2 to read and set
SNMP MIB parameters, however, for security reasons the configured
value is never displayed. The strings 'Enabled' and 'Disabled'
have special meanings and cannot be used as rwCommunity string.
Reading:
String 'Enabled' - A read-write community is configured
String 'Disabled' - The read-write community is disabled.
Writing:
String 'Disabled' - Disable the read-write community
Otherwise the written string becomes the new read-write
community (this implies that the read-write community is
enabled if it was earlier disabled.
Note that enabling the read-write community via SNMP is only
possible from SNMPv3.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.1.4 |
web OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.1.2 |
webEnabledWeb daemon enabled or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.2.1 |
ipconfig OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.1.3 |
ipconfigEnabledIPConfig daemon enabled or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.3.1 |
ssh OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.1.4 |
sshEnabledSSH daemon enabled or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.4.1 |
lldp OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.1.5 |
lldpEnabledLLDP service enabled or disabled.
- True: Enabling LLDP will enable the LLDP service with default settings.
- False: Disabling LLDP will fully disable the LLDP service, remove any
existing configuration, and disableaccess to any other LLDP OID
in private MIB andin LLDP MIB.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.5.1 |
lldpActivatedActivate/deactivate LLDP configuration.
- True: LLDP daemon enabled with existing configuration
- False: LLDP daemon deactivated. LLDP configuration (lldpPortConfigTable)
is kept and is still accessible. Configuration changes will not take
effect until lldpActivated is 'True'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.1.5.2 |
eventSystem OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.2 |
summaryAlarmStatusThe summaryAlarmStatus reports ''warning'' when at least one
of the configured alarm/event sources reports alarm condition.
WeOS supports an extensive set of alarm/event sources and a
flexible alarm handling framework.
The sources affecting the summaryAlarmStatus are those
configured to affect the unit's status LED, typically
labeled ''ON'' and located on the unit's front panel.ro Enumeration .1.3.6.1.4.1.2544.2.1.5.2.1 |
summaryAlarmTrapEnabledEnable/Disable support for sending summaryAlarm traps.
True(1) if summaryAlarm traps are enabled.
False(2) if summaryAlarm traps are disabled.
Traps will be sent if (and only if) the summaryAlarmStatus
changes status ('warning => ok' or 'ok => warning').rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.2.2 |
statusRelayDisplays the current state of the statusRelay (DigitalOut).ro Enumeration .1.3.6.1.4.1.2544.2.1.5.2.3 |
alarmStatusTableThe status for alarm triggers. SEQUENCE OF AlarmStatusEntry .1.3.6.1.4.1.2544.2.1.5.2.4 |
alarmStatusEntryAn entry containing information about a specific alarm trigger. AlarmStatusEntry .1.3.6.1.4.1.2544.2.1.5.2.4.1 |
alarmStatusTriggerIdThe id of alarm triggerro INTEGER .1.3.6.1.4.1.2544.2.1.5.2.4.1.1 |
alarmStatusTriggerTypeA text string containing description about the trigger typero DisplayString .1.3.6.1.4.1.2544.2.1.5.2.4.1.2 |
alarmStatusTriggerEnabledIndicates if the trigger is enabled or notro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.2.4.1.3 |
alarmStatusTriggerStatusThe actual alarm status for the triggerro Enumeration .1.3.6.1.4.1.2544.2.1.5.2.4.1.4 |
alarmStatusTriggerStatusReasonA text string containing status reasonro DisplayString .1.3.6.1.4.1.2544.2.1.5.2.4.1.5 |
statistics OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.3 |
memoryAvailDisplays the amount of available memory in kb for the system.ro Integer32 .1.3.6.1.4.1.2544.2.1.5.3.1 |
cpuLoadAvg OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.3.2 |
loadAvg1Displays a the cpu load average over 1 minute. The
value is displayed by taking the cpu load avgerage
value and multiplying it with 100.ro Integer32 .1.3.6.1.4.1.2544.2.1.5.3.2.1 |
loadAvg5Displays a the cpu load average over 5 minutes. The
value is displayed by taking the cpu load avgerage
value and multiplying it with 100.ro Integer32 .1.3.6.1.4.1.2544.2.1.5.3.2.2 |
loadAvg15Displays a the cpu load average over 15 minute. The
value is displayed by taking the cpu load avgerage
value and multiplying it with 100.ro Integer32 .1.3.6.1.4.1.2544.2.1.5.3.2.3 |
integrity OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.5.4 |
startupConfigurationHashA SHA-1 hash of the saved startup configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.4.1 |
runningConfigurationHashA SHA-1 hash of the current running configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.2.1.5.4.2 |
notifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6 |
sensorNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.1 |
sensorNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.1.0 |
digitalInHighNotification associated with digitalIn sensor state.
Sensor is of type TruthValue.
The 'entPhySensorValue' should always have value 'true(1)' in
a digitalInHigh trap, indicating that the voltage level is
above the required threshold (logical 1). NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.1.0.1 |
digitalInLowNotification associated with digitalIn sensor state.
Sensor is of type TruthValue.
The 'entPhySensorValue' should always have value 'false(2)' in
a digitalInLow trap, indicating that the voltage level is
below the required threshold (logical 0). NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.1.0.2 |
powerSupplyHighNotification associated with power supply sensor state.
Sensor is of type TruthValue
The 'entPhySensorValue' should always have value 'true(1)' in
a powerSupplyHigh trap, indicating that the voltage level is
above the required threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.1.0.3 |
powerSupplyLowNotification associated with power supply sensor state.
Sensor is of type TruthValue
The 'entPhySensorValue' should always have value 'false(2)' in
a powerSupplyLow trap, indicating that the voltage level is
below the required threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.1.0.4 |
temperatureHighNotification associated with temperature sensor state.
Sensor is of type 'Celsius'.
The 'entPhySensorValue' shows the temperature value at
the time the alarm system detected that the temperature had
rised to or passed beyond the configured alarm rising
threshold; except for temperatureHigh alarms at system
startup, this would typically be equal to the temperature
configured as the alarm rising threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.1.0.5 |
temperatureLowNotification associated with temperature sensor state.
Sensor is of type 'Celsius'.
The 'entPhySensorValue' shows the temperature value at
the time the alarm system detected that the temperature had
fallen to or passed below the configured alarm falling
threshold; except for temperatureLow alarms at system
startup, this would typically be equal to the temperature
configured as the alarm falling threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.1.0.6 |
frntNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.2 |
frntNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.2.0 |
frntv0RingUpNotification associated with FRNTv0 ring status.
The 'frntv0RingStatus' should always have value 'ring(1)' in
an frntv0RingUp trap.
Note that a focal point can detect both local
failures and elsewhere in the FRNT ring, while a member
switch is only able to detect local failures. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.2.0.1 |
frntv0RingDownNotification associated with FRNTv0 ring status.
The 'frntv0RingStatus' should always have value 'bus(2)' in
an frntv0RingDown trap.
Note that a focal point can detect both local
failures and elsewhere in the FRNT ring, while a member
switch is only able to detect local failures. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.2.0.2 |
lffNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.3 |
lffNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.3.0 |
lffRemoteUpNotification associated with link fault forward of remote
(Ethernet) link over an intermediate (SHDSL) link.
The 'lffStatus' should always have value 'remoteUp(4)' in
a lffRemoteUp, indicating that remote (Ethernet) link is
up. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.3.0.1 |
lffRemoteFailNotification associated with link fault forward of remote
(Ethernet) link over an intermediate (SHDSL) link.
The 'lffStatus' will show value
- 'remoteDown(3)' when information that the remote
(Ethernet) link is down is available.
- 'unknown(2)' when there is no information about the
state of the remote available, typically because the
intermediate (SHDSL) link is down. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.3.0.2 |
genericNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.4 |
genericNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.4.0 |
summaryStatusOKNotification that _none_ of the configured alarm sources
reports a bad state, i.e.,
- that the summaryAlarmStatus has _shifted_ from 'Warning
(1)' to 'Ok (2)', or
- that the unit started up with summaryStatus 'Ok (2)'. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.4.0.1 |
summaryStatusWarningNotification that at least one of the configured alarm
sources reports a bad state, i.e.,
- that the summaryAlarmStatus has _shifted_ from 'Ok (2)' to
'Warning (1)', or
- that the unit started up with summaryStatus 'Warning (1)'. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.4.0.2 |
ddmNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.5 |
ddmNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.5.0 |
ddmVoltageHighNotification associated with DDM voltage sensor state. The
'sfpDdmPortVoltage' shows the voltage value at the time the alarm
system detected that the voltage had rised to or passed beyond the
configured alarm rising threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.1 |
ddmVoltageLowNotification associated with DDM voltage sensor state. The
'sfpDdmPortVoltage' shows the voltage value at the time the alarm
system detected that the voltage had fallen to or passed below the
configured alarm falling threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.2 |
ddmTemperatureHighNotification associated with DDM temperature sensor state. The
'sfpDdmPortTemperature' shows the temperature value at the time the
alarm system detected that the temperature had rised to or passed
beyond the configured alarm rising threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.3 |
ddmTemperatureLowNotification associated with DDM temperature sensor state. The
'sfpDdmPortTemperature' shows the temperature value at the time the
alarm system detected that the temperature had fallen to or passed
below the configured alarm falling threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.4 |
ddmBiasCurrentHighNotification associated with DDM transmitt bias current sensor
state. The 'sfpDdmPortBiasCurrent' shows the bias current value at
the time the alarm system detected that the bias current had rised
to or passed beyond the configured alarm rising threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.5 |
ddmBiasCurrentLowNotification associated with DDM transmitt bias current sensor
state. The 'sfpDdmPortBiasCurrent' shows the bias current value at
the time the alarm system detected that the bias current had fallen
to or passed below the configured alarm falling threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.6 |
ddmTxPowerHighNotification associated with DDM transmitt power sensor state. The
'sfpDdmPortTxPower' shows the power value at the time the alarm
system detected that the power had rised to or passed beyond the
configured alarm rising threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.7 |
ddmTxPowerLowNotification associated with DDM transmitt power sensor state. The
'sfpDdmPortTxPower' shows the power value at the time the alarm
system detected that the power had fallen to or passed below the
configured alarm falling threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.8 |
ddmRxPowerHighNotification associated with DDM receiving power sensor state. The
'sfpDdmPortRxPower' shows the power value at the time the alarm
system detected that the power had rised to or passed beyond the
configured alarm rising threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.9 |
ddmRxPowerLowNotification associated with DDM receiving power sensor state. The
'sfpDdmPortRxPower' shows the power value at the time the alarm
system detected that the power had fallen to or passed below the
configured alarm falling threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.5.0.10 |
conflictNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.6 |
conflictNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.6.0 |
addressConflictDetectedAn Address Conflict have been detected. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.6.0.1 |
addressConflictClearedAn Address Conflict have been resolved. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.6.0.2 |
addressConflictOKThere are no Address Conflicts. This trap is sent when the last conflict is resolved. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.6.0.3 |
addressConflictWarningAn address conflict exists. This trap is sent when the first address conflict is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.6.0.4 |
otherNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.7 |
otherNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.7.0 |
mrpRingClosedNotification associated with MRP ring state. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.7.0.3 |
mrpRingOpenNotification associated with MRP ring state. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.7.0.4 |
riCoNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.8 |
riCoNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.8.0 |
riCoUplinkUpA RiCo or Dual Homing uplink has come up. The
riCoStatusUplinkStatus shows if the link comes up in role
Active or Backup. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.8.0.1 |
riCoUplinkDownA RiCo or Dual Homing uplink has gone down. The
riCoStatusUplinkStatus shows 'Down'. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.8.0.2 |
pingNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.9 |
pingNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2544.2.1.6.9.0 |
pingTriggerOkNotification associated with ping trigger status. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.9.0.1 |
pingTriggerWarningNotification associated with ping trigger status. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.2.1.6.9.0.2 |