VOLIUS-OT-MIB
AI MIB Summary
The VOLIUS-OT-MIB enables SNMP-based monitoring and management of Volius optical transport hardware, specifically fiber optical receivers, Erbium-doped fiber amplifiers (EDFAs), optical switches, and CATV optical transmitters. It provides access to device-specific operational metrics such as optical power levels, signal-to-noise ratios, amplifier gain settings, and switch port states for fault detection and performance analysis.
This MIB describes all SNMP-enabled hardware produced by Volius, such as Fiber optical receivers, Erbium-doped fiber amplifiers, Optical switches, CATV optical transmitters.
Main OID:
vlsGlobalModule.1.3.6.1.4.1.34652.1
85
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
85 total| Object Name |
|---|
volius OBJECT IDENTIFIER .1.3.6.1.4.1.34652 |
vlsGlobalModuleThis MIB describes all SNMP-enabled hardware produced by Volius, such as Fiber optical receivers, Erbium-doped fiber amplifiers, Optical switches, CATV optical transmitters. MODULE-IDENTITY .1.3.6.1.4.1.34652.1 |
vlsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2 |
vlsSystemGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.10 |
vlsModelNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.34652.2.10.1 |
vlsSerialNumberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.34652.2.10.2 |
vlsFirmwareVersionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.34652.2.10.3 |
vlsBootLoaderVersionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.34652.2.10.4 |
vlsDateAndTimero DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.34652.2.10.5 |
vlsTimeZoneDifference between local and UTC in minutes.rw Integer32 (-720..780) .1.3.6.1.4.1.34652.2.10.6 |
vlsCaseTemperaturero VlsDeciCelsius .1.3.6.1.4.1.34652.2.10.7 |
vlsFanSpeedro VlsRPM .1.3.6.1.4.1.34652.2.10.8 |
vlsSupplyVoltageTable SEQUENCE OF VlsSupplyVoltageEntry .1.3.6.1.4.1.34652.2.10.9 |
vlsSupplyVoltageEntry VlsSupplyVoltageEntry .1.3.6.1.4.1.34652.2.10.9.1 |
vlsSupplyVoltageIndexro Integer32 .1.3.6.1.4.1.34652.2.10.9.1.1 |
vlsSupplyVoltageNominalro VlsMillivolt .1.3.6.1.4.1.34652.2.10.9.1.2 |
vlsSupplyVoltageActualro VlsMillivolt .1.3.6.1.4.1.34652.2.10.9.1.3 |
vlsNetworkServices OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.11 |
vlsNetworkAddress OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.11.5 |
vlsMacAddressrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.34652.2.11.5.1 |
vlsIpAddressrw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.34652.2.11.5.2 |
vlsNetMaskrw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.34652.2.11.5.3 |
vlsDefaultGatewayrw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.34652.2.11.5.4 |
vlsHttp OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.11.6 |
vlsHttpPortrw Integer32 .1.3.6.1.4.1.34652.2.11.6.1 |
vlsHttpEnabledrw VlsOnOff .1.3.6.1.4.1.34652.2.11.6.2 |
vlsHttpPasswordEnabledrw VlsOnOff .1.3.6.1.4.1.34652.2.11.6.3 |
vlsSnmp OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.11.7 |
vlsSnmpPortrw Integer32 .1.3.6.1.4.1.34652.2.11.7.1 |
vlsTrapDestTable SEQUENCE OF VlsTrapDestEntry .1.3.6.1.4.1.34652.2.11.7.2 |
vlsTrapDestEntry VlsTrapDestEntry .1.3.6.1.4.1.34652.2.11.7.2.1 |
vlsTrapDestIndexro Integer32 .1.3.6.1.4.1.34652.2.11.7.2.1.1 |
vlsTrapDestAddrrw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.34652.2.11.7.2.1.2 |
vlsTrapDestPortrw Integer32 .1.3.6.1.4.1.34652.2.11.7.2.1.3 |
vlsTrapDestEnablerw VlsOnOff .1.3.6.1.4.1.34652.2.11.7.2.1.4 |
vlsSntp OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.11.8 |
vlsSntpServerAddrrw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.34652.2.11.8.1 |
vlsSntpServerPortrw Integer32 .1.3.6.1.4.1.34652.2.11.8.2 |
vlsSntpEnabledrw VlsOnOff .1.3.6.1.4.1.34652.2.11.8.3 |
vlsEventLog OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.13 |
vlsLastEventCodero VlsEvent .1.3.6.1.4.1.34652.2.13.1 |
vlsLastEventIndexro Integer32 .1.3.6.1.4.1.34652.2.13.2 |
vlsEventLogSizeNumber of events stored in the log.ro Integer32 .1.3.6.1.4.1.34652.2.13.3 |
vlsEventLogTable SEQUENCE OF VlsEventLogEntry .1.3.6.1.4.1.34652.2.13.4 |
vlsEventLogEntry VlsEventLogEntry .1.3.6.1.4.1.34652.2.13.4.1 |
vlsEventIndexro Integer32 .1.3.6.1.4.1.34652.2.13.4.1.1 |
vlsEventCodero VlsEvent .1.3.6.1.4.1.34652.2.13.4.1.2 |
vlsEventTimeStampro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.34652.2.13.4.1.3 |
vlsEventDateTimero DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.34652.2.13.4.1.4 |
vlsEventMessagero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.34652.2.13.4.1.5 |
vlsEventTrap NOTIFICATION-TYPE .1.3.6.1.4.1.34652.2.13.8 |
vlsAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.34652.2.14 |
vlsAlarmsActiveMaskThis is a bit mask where all active alarms are combined. Alarms are latching, that is an alarm is still active even when the condition activating the alarm no longer exists.ro Integer32 .1.3.6.1.4.1.34652.2.14.1 |
vlsAlarmsResetMaskYou can write reset mask to reset individual alarms. An alarm will be reset only if the activating condition no longer exists.rw Integer32 .1.3.6.1.4.1.34652.2.14.2 |
vlsAlarmsTable SEQUENCE OF VlsAlarmsEntry .1.3.6.1.4.1.34652.2.14.3 |
vlsAlarmsEntry VlsAlarmsEntry .1.3.6.1.4.1.34652.2.14.3.1 |
vlsAlarmIndexro Integer32 .1.3.6.1.4.1.34652.2.14.3.1.1 |
vlsAlarmStateWhen read, this OID indicates if the alarm is active. When vlsOff is written to this OID, the alarm is reset.rw VlsOnOff .1.3.6.1.4.1.34652.2.14.3.1.2 |
vlsAlarmMessagero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.34652.2.14.3.1.3 |
vlsEdfa OBJECT IDENTIFIER .1.3.6.1.4.1.34652.3 |
vlsOpticalSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.34652.4 |
vlsCatvTransmitter OBJECT IDENTIFIER .1.3.6.1.4.1.34652.5 |
vlsTxEmissionStateReports whether the laser is on or off.ro VlsOnOff .1.3.6.1.4.1.34652.5.1 |
vlsTxOutputTable SEQUENCE OF VlsTxOutputEntry .1.3.6.1.4.1.34652.5.2 |
vlsTxOutputEntry VlsTxOutputEntry .1.3.6.1.4.1.34652.5.2.1 |
vlsTxOutputIndexOptical output number (1 or 2).ro Integer32 .1.3.6.1.4.1.34652.5.2.1.1 |
vlsTxOutputPowerOptical output level.ro VlsDeciDbm .1.3.6.1.4.1.34652.5.2.1.2 |
vlsTxPoutLowAlarmOutput power low alarm threshold.rw VlsDeciDbm .1.3.6.1.4.1.34652.5.3 |
vlsTxPoutHighAlarmOutput power high alarm threshold.rw VlsDeciDbm .1.3.6.1.4.1.34652.5.4 |
vlsTxInputCompositeComposite RF level at the transmitter input.ro VlsDbm .1.3.6.1.4.1.34652.5.5 |
vlsTxInputPerChannelPer-channel RF level at the transmitter input.ro VlsDbuv .1.3.6.1.4.1.34652.5.6 |
vlsTxChannelPwrFactorThis factor is used to convert composite RF level to per-channel RF level. The factor is expressed in units of 0.1 dB and is always negative or zero. For example, if the channel plan is 100 channels all with the same RF level, the factor should be -200 (meaning -20.0 dB). Then, if composite RF level is 0 dBm (that is 108.75 dBuV), per-channel RF level would be 108.75 - 20 = 88.75 dBuV.rw VlsDeciDb .1.3.6.1.4.1.34652.5.7 |
vlsTxOmiComposite OMI in units of 0.1%.ro VlsPerMille .1.3.6.1.4.1.34652.5.8 |
vlsTxAttActual variable attenuator state. The range is 0..25 dB.ro VlsDeciDb .1.3.6.1.4.1.34652.5.9 |
vlsTxLaserCurrentLaser current. 100% corresponds to the current set during factory calibration. The current is expected to rise slowly after years of operation (laser aging).ro VlsPercent .1.3.6.1.4.1.34652.5.10 |
vlsTxLaserTecCurrentro VlsPercent .1.3.6.1.4.1.34652.5.11 |
vlsTxLaserPowerro VlsDeciDbm .1.3.6.1.4.1.34652.5.12 |
vlsTxLaserTemperaturero VlsDeciCelsius .1.3.6.1.4.1.34652.5.13 |
vlsTxAgcAGC mode on/off control.rw VlsOnOff .1.3.6.1.4.1.34652.5.14 |
vlsTxSetOmiOMI setpoint when AGC is on.rw VlsPerMille .1.3.6.1.4.1.34652.5.15 |
vlsTxSetAttVariable attenuator setpoint when AGC is off.rw VlsDeciDb .1.3.6.1.4.1.34652.5.16 |
vlsTxSetSbsThresholdSBS suppression level.rw VlsDbm .1.3.6.1.4.1.34652.5.17 |
vlsOpticalReceiver OBJECT IDENTIFIER .1.3.6.1.4.1.34652.6 |
vlsCabinetMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.34652.7 |
vlsUpsMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.34652.8 |