VDSL-LINE-EXT-MCM-MIB
The VDSL-LINE-MIB found in RFC 3728 defines objects for the management of a pair of VDSL transceivers at each end of the VDSL line. The VDSL-LINE-MIB configures and monitors the line code independent parameters (TC layer) of the VDSL line. This MIB module is an optional extension of the VDSL-LINE-MIB and defines objects for configuration and monitoring of the line code specific (LCS) elements (PMD layer) for VDSL lines using MCM coding. The objects in this extension MIB MUST NOT be used for VDSL lines using Single Carrier Modulation (SCM) line coding. If an object in this extension MIB is referenced by a line which does not use MCM, it has no effect on the operation of that line. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current LCS -- Line Code Specific Max -- Maximum PSD -- Power Spectral Density Rx -- Receive Tx -- Transmit Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4070: see the RFC itself for full legal notices.
Main OID:
vdslExtMCMMIB.1.3.6.1.2.1.10.229
42
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
42 total| Object Name |
|---|
vdslExtMCMMIBThe VDSL-LINE-MIB found in RFC 3728 defines objects for the management of a pair of VDSL transceivers at each end of the VDSL line. The VDSL-LINE-MIB configures and monitors the line code independent parameters (TC layer) of the VDSL line. This MIB module is an optional extension of the VDSL-LINE-MIB and defines objects for configuration and monitoring of the line code specific (LCS) elements (PMD layer) for VDSL lines using MCM coding. The objects in this extension MIB MUST NOT be used for VDSL lines using Single Carrier Modulation (SCM) line coding. If an object in this extension MIB is referenced by a line which does not use MCM, it has no effect on the operation of that line. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current LCS -- Line Code Specific Max -- Maximum PSD -- Power Spectral Density Rx -- Receive Tx -- Transmit Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4070: see the RFC itself for full legal notices. MODULE-IDENTITY .1.3.6.1.2.1.10.229 |
vdslLineExtMCMMib OBJECT IDENTIFIER .1.3.6.1.2.1.10.229.1 |
vdslLineExtMCMMibObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.229.1.1 |
vdslLineMCMConfProfileTableThis table contains additional information on multiple carrier VDSL lines. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently. SEQUENCE OF VdslLineMCMConfProfileEntry .1.3.6.1.2.1.10.229.1.1.1 |
vdslLineMCMConfProfileEntryEach entry consists of a list of parameters that represents the configuration of a multiple carrier modulation VDSL modem. VdslLineMCMConfProfileEntry .1.3.6.1.2.1.10.229.1.1.1.1 |
vdslLineMCMConfProfileTxWindowLengthSpecifies the length of the transmit window, counted in samples at the sampling rate corresponding to the negotiated value of N.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.1.1.1 |
vdslLineMCMConfProfileRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `active'. When `active' is set, the system will validate the profile. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must first be unreferenced from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.229.1.1.1.1.2 |
vdslLineMCMConfProfileTxBandTableThis table contains transmit band descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one of possibly many bands with a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently. SEQUENCE OF VdslLineMCMConfProfileTxBandEntry .1.3.6.1.2.1.10.229.1.1.2 |
vdslLineMCMConfProfileTxBandEntryEach entry consists of a transmit band descriptor, which is defined by a start and a stop tone index. VdslLineMCMConfProfileTxBandEntry .1.3.6.1.2.1.10.229.1.1.2.1 |
vdslLineMCMConfProfileTxBandNumberThe index for this band descriptor entry. Unsigned32 .1.3.6.1.2.1.10.229.1.1.2.1.1 |
vdslLineMCMConfProfileTxBandStartStart tone index for this band.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.2.1.2 |
vdslLineMCMConfProfileTxBandStopStop tone index for this band.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.2.1.3 |
vdslLineMCMConfProfileTxBandRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `active'. When `active' is set, the system will validate the profile. Each entry must be internally consistent, the Stop Tone must be greater than the Start Tone. Each entry must also be externally consistent, all entries indexed by a specific profile must not overlap. Validation of the profile will check both internal and external consistency. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.229.1.1.2.1.4 |
vdslLineMCMConfProfileRxBandTableThis table contains receive band descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one of possibly many bands with a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently. SEQUENCE OF VdslLineMCMConfProfileRxBandEntry .1.3.6.1.2.1.10.229.1.1.3 |
vdslLineMCMConfProfileRxBandEntryEach entry consists of a transmit band descriptor, which is defined by a start and a stop tone index. VdslLineMCMConfProfileRxBandEntry .1.3.6.1.2.1.10.229.1.1.3.1 |
vdslLineMCMConfProfileRxBandNumberThe index for this band descriptor entry. Unsigned32 .1.3.6.1.2.1.10.229.1.1.3.1.1 |
vdslLineMCMConfProfileRxBandStartStart tone index for this band.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.3.1.2 |
vdslLineMCMConfProfileRxBandStopStop tone index for this band.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.3.1.3 |
vdslLineMCMConfProfileRxBandRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `active'. When `active' is set, the system will validate the profile. Each entry must be internally consistent, the Stop Tone must be greater than the Start Tone. Each entry must also be externally consistent, all entries indexed by a specific profile must not overlap. Validation of the profile will check both internal and external consistency. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.229.1.1.3.1.4 |
vdslLineMCMConfProfileTxPSDTableThis table contains transmit PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently. SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry .1.3.6.1.2.1.10.229.1.1.4 |
vdslLineMCMConfProfileTxPSDEntryEach entry consists of a transmit PSD mask descriptor, which defines the power spectral density (PSD) for a tone. VdslLineMCMConfProfileTxPSDEntry .1.3.6.1.2.1.10.229.1.1.4.1 |
vdslLineMCMConfProfileTxPSDNumberThe index for this mask descriptor entry. Unsigned32 .1.3.6.1.2.1.10.229.1.1.4.1.1 |
vdslLineMCMConfProfileTxPSDToneThe tone index for which the PSD is being specified.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.4.1.2 |
vdslLineMCMConfProfileTxPSDPSDPower Spectral Density level in steps of 0.5dBm/Hz with an offset of -140dBm/Hz.rw Unsigned32 UNITS "0.5dBm/Hz" .1.3.6.1.2.1.10.229.1.1.4.1.3 |
vdslLineMCMConfProfileTxPSDRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `active'. When `active' is set, the system will validate the profile. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.229.1.1.4.1.4 |
vdslLineMCMConfProfileMaxTxPSDTableThis table contains transmit maximum PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL modem. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently. SEQUENCE OF VdslLineMCMConfProfileMaxTxPSDEntry .1.3.6.1.2.1.10.229.1.1.5 |
vdslLineMCMConfProfileMaxTxPSDEntryEach entry consists of a transmit PSD mask descriptor, which defines the maximum power spectral density (PSD) for a tone. VdslLineMCMConfProfileMaxTxPSDEntry .1.3.6.1.2.1.10.229.1.1.5.1 |
vdslLineMCMConfProfileMaxTxPSDNumberThe index for this band descriptor entry. Unsigned32 .1.3.6.1.2.1.10.229.1.1.5.1.1 |
vdslLineMCMConfProfileMaxTxPSDToneThe tone index for which the PSD is being specified. There must not be multiple rows defined, for a particular profile, with the same value for this field.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.5.1.2 |
vdslLineMCMConfProfileMaxTxPSDPSDPower Spectral Density level in steps of 0.5dBm/Hz with an offset of -140dBm/Hz.rw Unsigned32 UNITS "0.5dBm/Hz" .1.3.6.1.2.1.10.229.1.1.5.1.3 |
vdslLineMCMConfProfileMaxTxPSDRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `active'. When `active' is set, the system will validate the profile. There must be only one entry in this table for each tone associated with a specific profile. This will be checked during the validation process. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.229.1.1.5.1.4 |
vdslLineMCMConfProfileMaxRxPSDTableThis table contains maximum receive PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL modem. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently. SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry .1.3.6.1.2.1.10.229.1.1.6 |
vdslLineMCMConfProfileMaxRxPSDEntryEach entry consists of a transmit PSD mask descriptor, which defines the power spectral density (PSD) for a tone. VdslLineMCMConfProfileMaxRxPSDEntry .1.3.6.1.2.1.10.229.1.1.6.1 |
vdslLineMCMConfProfileMaxRxPSDNumberThe index for this band descriptor entry. Unsigned32 .1.3.6.1.2.1.10.229.1.1.6.1.1 |
vdslLineMCMConfProfileMaxRxPSDToneThe tone index for which the PSD is being specified. There must not be multiple rows defined, for a particular profile, with the same value for this field.rw Unsigned32 .1.3.6.1.2.1.10.229.1.1.6.1.2 |
vdslLineMCMConfProfileMaxRxPSDPSDPower Spectral Density level in steps of 0.5dBm/Hz with an offset of -140dBm/Hz.rw Unsigned32 UNITS "0.5dBm/Hz" .1.3.6.1.2.1.10.229.1.1.6.1.3 |
vdslLineMCMConfProfileMaxRxPSDRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `active'. When `active' is set, the system will validate the profile. There must be only one entry in this table for each tone associated with a specific profile. This will be checked during the validation process. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.229.1.1.6.1.4 |
vdslLineExtMCMConformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.229.1.2 |
vdslLineExtMCMGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.229.1.2.1 |
vdslLineExtMCMGroupA collection of objects providing configuration information for a VDSL line based upon multiple carrier modulation modem. Unknown .1.3.6.1.2.1.10.229.1.2.1.1 |
vdslLineExtMCMCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.229.1.2.2 |
vdslLineExtMCMMibComplianceThe compliance statement for SNMP entities which manage VDSL interfaces. Unknown .1.3.6.1.2.1.10.229.1.2.2.1 |