VDSL-DMT-LINE-MIB
This MIB module defines a collection of objects for managing VDSL DMT Lines. These objects extend the ADSL-LINE-MIB (RFC2662).
Main OID:
vdslDMTMib.1.3.6.1.2.1.10.94.4
23
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
23 total| Object Name |
|---|
vdslDMTMibThis MIB module defines a collection of objects for
managing VDSL DMT Lines. These objects extend the ADSL-LINE-MIB
(RFC2662). MODULE-IDENTITY .1.3.6.1.2.1.10.94.4 |
vdslDMTMibObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.4.1 |
vdslDMTConfProfileTableThis table contains configuration parameters that
apply to VDSL modems. SEQUENCE OF VdslDMTConfProfileEntry .1.3.6.1.2.1.10.94.4.1.1 |
vdslDMTConfProfileEntryAn entry for the vdslDMTConfProfileTable VdslDMTConfProfileEntry .1.3.6.1.2.1.10.94.4.1.1.1 |
vdslDmtConfProfileSSFTotalTotal number of symbols per superframe. Note that currently
the total must be set to 20. The sum of
up-stream-symbols+down-stream-symbols+quiescent-symbols must
be equal to total-symbols. Note that currently
quiescent-symbols=2. Note that currently down-stream-symbols
can be in the range 7..16rw VdslDmtConfProfileSSF UNITS "Number of Symbols" .1.3.6.1.2.1.10.94.4.1.1.1.1 |
vdslDmtConfProfileSSFDownStreamNumber of down stream symbols per superframe. The sum of
up-stream-symbols+down-stream-symbols+quiescent-symbols must
be equal to total-symbols. Note that currently
quiescent-symbols = 2. Note that currently
down-stream-symbols can be in the range 7..16rw VdslDmtConfProfileSSF UNITS "Number of Symbols" .1.3.6.1.2.1.10.94.4.1.1.1.2 |
vdslDmtConfProfileLowSpectrumThe lower edge of the down stream and up stream transmit
spectrum is controlled by this setting. This setting is the
first bin on which to transmit/receive.rw VdslDmtConfProfileSpectrum UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.3 |
vdslDmtConfProfileHighSpectrumThe highest edge of the down stream and up stream transmit
spectrum is controlled by this setting. This setting is the
last bin on which to transmit/receiverw VdslDmtConfProfileSpectrum UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.4 |
vdslDmtConfProfileRFIEnableEnable/disable the RFI canceller. Enabling the RFI
canceller mitigates egress into the bands specified by
RFIBands and prevents the modems from transmitting on
subchannels within those bands.rw VdslDmtConfProfileRFIEnable .1.3.6.1.2.1.10.94.4.1.1.1.5 |
vdslDmtConfProfileRFIBand1LowThis setting specifies the start frequency of RFI band 1.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.6 |
vdslDmtConfProfileRFIBand1HighThis setting specifies the stop frequency of RFI band 1.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.7 |
vdslDmtConfProfileRFIBand2LowThis setting specifies the start frequency of RFI band 2.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.8 |
vdslDmtConfProfileRFIBand2HighThis setting specifies the stop frequency of RFI band 2.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.9 |
vdslDmtConfProfileRFIBand3LowThis setting specifies the start frequency of RFI band 3.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.10 |
vdslDmtConfProfileRFIBand3HighThis setting specifies the stop frequency of RFI band 3.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.11 |
vdslDmtConfProfileRFIBand4LowThis setting specifies the start frequency of RFI band 4.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.12 |
vdslDmtConfProfileRFIBand4HighThis setting specifies the stop frequency of RFI band 4.rw VdslDmtConfProfileRFIBand UNITS "Bin number" .1.3.6.1.2.1.10.94.4.1.1.1.13 |
vdslDmtConfProfilePowerCutbackThis array is used to set the desired receive Power Spectral
Density (PSD) at a value below the maximum transmit PSD.rw VdslDmtConfProfilePowerCutback UNITS "dB down from maximum power" .1.3.6.1.2.1.10.94.4.1.1.1.14 |
vdslDmtConfProfilePowerBoostThis variable is used to specify a boost value for the
transmit Power Spectral Density (PSD).rw VdslDmtConfProfilePowerBoost .1.3.6.1.2.1.10.94.4.1.1.1.15 |
vdslDmtConfProfileEnergyRedistThis variable enables/disable energy redistribution.
Use of energy redistribution allows energy that would have
been allocated to subchannels that are not used to be
redistributed to subchannels supporting data transmission.rw VdslDmtConfProfileEnergyRedist .1.3.6.1.2.1.10.94.4.1.1.1.16 |
vdslConformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.4.2 |
vdslGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.4.2.1 |
vdslCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.94.4.2.2 |
More MIBs from Presticom
Browse all PresticomMIBs →PRESTICOM7-MIB
SNMP MIB module
884 objects→
CLEARTRAC7-MIB
Standard SNMP MIB module defining data structures for CLEARTRAC7-MIB.
871 objects→
IPSEC-POLICY-MIB
SNMP MIB module
389 objects→
APPN-MIB
The APPN-MIB provides standardized SNMP objects to monitor and manage Advanced Peer-to-Peer Networking (APPN) instances on network devices, specifically tracking high-level topology elements such as network nodes, logical links, and session states. It enables administrators to observe APPN-specific performance metrics including node availability, link utilization, and the status of dynamic routing tables within the SNA over TCP/IP or native SNA environments.
370 objects→
APPC-MIB
The APPC-MIB facilitates the monitoring and management of IBM Systems Network Architecture (SNA) Advanced Program-to-Program Communication (APPC) sessions and logical units on network devices. It exposes specific metrics including session states, connection establishment failures, and resource utilization counters to enable troubleshooting of legacy SNA over IP or TCP/IP transport layers.
295 objects→
APPLETALK-MIB
Standard SNMP MIB module defining data structures for APPLETALK-MIB.
284 objects→