Unisphere-Data-PPPOE-PROFILE-MIB
The Unisphere-Data-PPPOE-PROFILE-MIB enables monitoring and configuration of Point-to-Point Protocol over Ethernet (PPPoE) session profiles and parameters on EMC Unisphere-managed storage arrays. It provides visibility into PPPoE interface states, authentication settings, and session establishment metrics specific to the Juniper enterprise networking environment integrated with these storage systems.
Imported Objects
Objects
23 total| Object Name |
|---|
usdPppoeProfileMIBThe point-to-point protocol over Ethernet (PPPoE) profile MIB for the Juniper enterprise. MODULE-IDENTITY .1.3.6.1.4.1.4874.2.2.46 |
usdPppoeProfileObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.46.1 |
usdPppoeProfile OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.46.1.1 |
usdPppoeProfileTableThis table contains profiles for configuring PPPoE interfaces/sessions. Entries in this table are created/deleted as a side-effect of corresponding operations to the usdProfileNameTable in the Unisphere-Data-PROFILE-MIB. SEQUENCE OF UsdPppoeProfileEntry .1.3.6.1.4.1.4874.2.2.46.1.1.1 |
usdPppoeProfileEntryA profile describing configuration of a PPPoE interface and its subinterfaces (sessions). UsdPppoeProfileEntry .1.3.6.1.4.1.4874.2.2.46.1.1.1.1 |
usdPppoeProfileIdThe integer identifier associated with this profile. A value for this identifier is determined by locating or creating a profile name in the usdProfileNameTable. Unsigned32 .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.1 |
usdPppoeProfileSetMapA bitmap representing which objects in this entry have been explicitly configured. See the definition of the UsdSetMap TEXTUAL-CONVENTION for details of use. The INDEX object(s) and this object are excluded from representation (i.e. their bits are never set). When a SET request does not explicitly configure UsdSetMap, bits in UsdSetMap are set as a side-effect of configuring other profile attributes in the same entry. If, however, a SET request explicitly configures UsdSetMap, the explicitly configured value overrides 1) any previous bit settings, and 2) any simultaneous 'side-effect' settings that would otherwise occur. Once set, bits can only be cleared by explicitly configuring UsdSetMap.rw UsdSetMap (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.2 |
usdPppoeProfileMaxNumSessionsThe maximum number of PPPoE sessions (subinterfaces) that can be configured on the main PPPoE interface created using this profile. A value of zero indicates no bound is configured.rw Integer32 .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.3 |
usdPppoeProfileSubMotmA message to send via a PADM on the sub-interface when this profile is applied to the IP interface above this PPPoE sub- interface. A client may choose to display this message to the user.rw DisplayString .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.4 |
usdPppoeProfileSubUrlA URL to be sent via a PADM on the sub-interface when this profile is applied to the IP interface above this PPPoE sub-interface. The string entered here can have several substitutions applied: %D is replaced with the profile name %d is replaced with the domain name %u is replaced with the user name %U is replaced with the user/domain name together %% is replaced with the % character The resulting string must not be greater than 127 octets long. The client may use this URL as the initial web-page for the user.rw DisplayString .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.5 |
usdPppoeProfileDupProtectFlag to control whether duplicate MAC addresses are allowedrw UsdEnable (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.6 |
usdPppoeProfileAcNameThe name to use for the AC-NAME tag that is sent in any PADO that is sent on this interface.rw DisplayString .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.7 |
usdPppoeProfilePadiFlagThe PPPoE major interface parameter PADI flag controls whether to always repsond to a PADI with a PADO regardless of the ability to create the session and allow the session establish phase to resolve it.rw UsdEnable (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.8 |
usdPppoeProfilePacketTraceThe PPPoE major interface parameter packet tracing flag controls whether packet tracing is enable or not.rw UsdEnable (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.46.1.1.1.1.9 |
usdPppoeProfileConformance OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.46.4 |
usdPppoeProfileCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.46.4.1 |
usdPppoeProfileComplianceObsolete compliance statement for entities which implement the Juniper PPPoE Profile MIB. This statement became obsolete when the duplicate MAC address indicator and AC-NAME tag were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.46.4.1.1 |
usdPppoeCompliance2Obsolete compliance statement for entities which implement the Juniper PPPoE profile MIB. This statement became obsolete when PADI flag, AC-name and packet trace objects were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.46.4.1.2 |
usdPppoeCompliance3The compliance statement for entities which implement the Juniper PPPoE Profile MIB. Unknown .1.3.6.1.4.1.4874.2.2.46.4.1.3 |
usdPppoeProfileGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.46.4.2 |
usdPppoeProfileGroupObsolete collection of objects providing management of profile functionality for PPPoE interfaces in a Juniper product. This group became obsolete when the duplicate MAC address indicator and AC-NAME tag objects were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.46.4.2.1 |
usdPppoeProfileGroup2Obsolete collection of objects providing management of profile functionality for PPPOE interfaces in a Unisphere product. This group became obsolete when PADI flag, AC-name and packet trace objects were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.46.4.2.2 |
usdPppoeProfileGroup3A collection of objects providing management of profile functionality for PPPOE interfaces in a Unisphere product. Unknown .1.3.6.1.4.1.4874.2.2.46.4.2.3 |
More MIBs from Unisphere
Browse all UnisphereMIBs →SNMP MIB module
The Unisphere-Data-BGP-MIB enables monitoring and management of Border Gateway Protocol (BGP) session states, routing table statistics, and neighbor relationships on Dell EMC Unisphere for Data storage systems. It provides access to standard BGP MIB objects for tracking peer connectivity, route advertisements, and protocol error counters within the storage network infrastructure.
The Juniper-RADIUS-CLIENT-MIB enables monitoring of RADIUS client authentication sessions, accounting records, and server reachability states on Juniper network devices. It provides specific counters and gauges for tracking authentication failures, successful logins, and RADIUS server response times to validate access control infrastructure health.
The Juniper-UNI-ATM-MIB module provides SNMP management capabilities for Juniper devices configured with Asynchronous Transfer Mode (ATM) user-network interfaces, enabling the monitoring of ATM-specific performance counters, interface states, and VPI/VCI traffic statistics.
The Juniper-AAA-MIB enables monitoring of authentication, authorization, and accounting events on Juniper Networks devices, specifically tracking user session states, login success/failure counts, and accounting record generation for RADIUS and TACACS+ protocols.
SNMP MIB module