Unisphere-Data-MPLS-MIB
AI MIB Summary
The Unisphere-Data-MPLS-MIB enables management of Unisphere Networks label switching routers by exposing configuration objects for global LSR parameters, interface and tunnel settings, tunnel profiles, explicit paths, and BGP/MPLS or CR-LDP VPN instances.
The MultiProtocol Label Switching (MPLS) MIB for the Unisphere Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations.
Main OID:
usdMplsMIB.1.3.6.1.4.1.4874.2.2.54
204
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
204 total| Object Name |
|---|
usdMplsMIBThe MultiProtocol Label Switching (MPLS) MIB for the Unisphere Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations. MODULE-IDENTITY .1.3.6.1.4.1.4874.2.2.54 |
usdMplsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1 |
usdMplsLsrGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.1 |
usdMplsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.1.1 |
usdMplsGroupMplsEnableEnables or disables MPLS on the virtual router. When MPLS is created on the virtual router (VR), it remains adminstratively disabled untill it is enabled explicitly. Without administratively enabling the MPLS on VR, it won't function as an LSR even though it holds the MPLS configurations until the MPLS context is destroyed for the VR.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.1 |
usdMplsGroupReopTimerAll LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. This object allows configuration of the frequency of reoptimization in time interval.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.2 |
usdMplsGroupLabelRangeLowThe lower end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.3 |
usdMplsGroupLabelRangeHighThe higher end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.4 |
usdMplsGroupLspRetryTimesNorouteThis object configures the number of retries for LSP setup after a failure due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.5 |
usdMplsGroupLspRetryIntervalNorouteThis object configures the time interval between two successive LSP setup retries after a failure due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.6 |
usdMplsGroupLspRetryTimesUse this object to configure number of retries for LSP setup after a failure other than one due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.7 |
usdMplsGroupLspRetryIntervalUse this object to configure the time interval between two LSP setup retries after a failure other than one due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.8 |
usdMplsGroupLdpRetryTimesNorouteUse this object to configure the number of retries for LDP to setup LSP after a failure due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.9 |
usdMplsGroupLdpRetryIntervalNorouteUse this object to configure the time interval between two successive LSP setup retries by LDP after a failure due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.10 |
usdMplsGroupLdpRetryTimesUse this object to configure LSP setup retries by LDP after a failure other than one due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.11 |
usdMplsGroupLdpRetryIntervalUse this object to configure time interval between two LSP setup retries by LDP after a failure other than one due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.12 |
usdMplsGroupLdpSessionRetriesUse this object to configure the number of LDP session retries.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.13 |
usdMplsGroupLdpSessionRetryTimerUse this object to configure the time interval between two LDP session retries.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.14 |
usdMplsGroupTopologyDrivenIpProfileNameUsually IP interfaces are stacked on top of the MPLS tunnels. The profiled tunnels are associated with IP interfaces with profile of IP interfaces. This object configures the name for the IP profile.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.15 |
usdMplsGroupTopologyDrivenLdpEgressIpIntfThis object allows enabling/disabling of IP interfaces created over egress LSPs setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.16 |
usdMplsGroupTopologyDrivenLdpIngressIpIntfThis object allows enabling/disabling of IP interfaces created over ingress LSPs setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.17 |
usdMplsGroupTopologyDrivenLdpEgressIpIntfHostOnlyThis object allows enabling/disabling of IP interfaces created over egress LSPs to host only IP addresses setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.18 |
usdMplsGroupTopologyDrivenLdpIngressIpIntfHostOnlyThis object allows enabling/disabling of IP interfaces created over ingress LSPs to host only IP addresses setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.19 |
usdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListTypeThere are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the egress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.20 |
usdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListTypeThere are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the ingress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.21 |
usdMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListThis object used to configure egress list name of topology driven LSPs over IP interfaces. For successful configurations the egress list name must be set cunncurently with egress list type. Set the list type and list name cuncurrently.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.22 |
usdMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListThis object used to configure ingress list name of topology driven LSPs over IP interfaces. For successful configurations ingress listname set cunncurently with ingress list type. Set the list type and list name cuncurrently.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.23 |
usdMplsGroupTopologyDrivenLdpLDP is used for label distributions control for setting up the LSPs. Topology driven LSPs also setup using LDP label distribution control. This object allows to enable/disable LDP admin state used for topology driven LSPs setup.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.24 |
usdMplsGroupLspLabelDistCtrlModeSome FECs correspond to address prefixes which are distributed via a dynamic routing algorithm. The setup of the LSPs for these FECs can be done in one of two ways: Independent LSP Control or Ordered LSP Control. This object displays the LSP lable distribution control mode.ro Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.25 |
usdMplsGroupLdpAdvHostOnlyThis object allows to enable/disable LDP label advertisement mode for host only LSPs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.26 |
usdMplsGroupLsrStateThis object value displays the status of MPLS enabled LSR such as state is up or down etc.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.27 |
usdMplsGroupReopNowAll LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. Setting this object forces an immediate check for better paths for the existing LSPs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.28 |
usdMplsGroupList OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.1.2 |
usdMplsGroupTargetedHelloSendTableThis table contains list of send side IP addresses for LDP targeted hello messages. SEQUENCE OF UsdMplsGroupTargetedHelloSendEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.1 |
usdMplsGroupTargetedHelloSendEntryEach entry represents send IP address for targeted hello message. UsdMplsGroupTargetedHelloSendEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1 |
usdMplsGroupTargetedHelloSendAddressConfigure the send side address for targeted hello messages. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.1 |
usdMplsGroupLdpTargetedHelloSendModeSelect mode to add/delete to the list of IP addresses for targeted hello messages.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.2 |
usdMplsGroupTargetedHelloReceiveTableThis table contains list of receive side IP addresses for LDP targeted hello messages. SEQUENCE OF UsdMplsGroupTargetedHelloReceiveEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.2 |
usdMplsGroupTargetedHelloReceiveEntryEach entry represents receive IP address for targeted hello message. UsdMplsGroupTargetedHelloReceiveEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1 |
usdMplsGroupTargetedHelloReceiveAddressConfigure the receive side address for targeted hello messages. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.1 |
usdMplsGroupLdpTargetedHelloReceiveModeSelect mode to add/delete to the list of IP addresses for targeted hello messages.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.2 |
usdMplsGroupLdpLabelAdverRouteListTableTable is a list of LDP label advertisement entries. SEQUENCE OF UsdMplsGroupLdpLabelAdverRouteListEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.3 |
usdMplsGroupLdpLabelAdverRouteListEntryEach entry represents access list pairs for the LDP peers label advertisement. UsdMplsGroupLdpLabelAdverRouteListEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1 |
usdMplsGroupLdpLabelAdverRouteListNameThis LDP label advertisement route list name for which this entry contains information. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.1 |
usdMplsGroupLdpLabelAdverNbrListNameThe LDP label advertisement neighbor route list name for which this entry contains information. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.2 |
usdMplsGroupLabelAdverListModeThis object selects the mode of addition/deletion to the list.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.3 |
usdMplsGroupLdpProfileTableTable is a list of LDP Profile entries. SEQUENCE OF UsdMplsGroupLdpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.4 |
usdMplsGroupLdpProfileEntryEach entry represents one LDP profile settings. UsdMplsGroupLdpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1 |
usdMplsGroupLdpProfileNameLDP profile name identifies unique entry in the table. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.1 |
usdMplsGroupLdpProfileHelloHoldTimeConfigure the LDP peers hello hold time period.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.2 |
usdMplsGroupLdpProfileCrLdpAdminStateEnable or disable the constraint-based routing label distribution protocol (CR-LDP) admin state.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.3 |
usdMplsGroupLdpProfileRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsGroupLdpProfileCrLdpAdminState usdMplsGroupLdpProfileRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.4 |
usdMplsGroupRsvpProfileTableTable is a list of LDP Profile entries. SEQUENCE OF UsdMplsGroupRsvpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.5 |
usdMplsGroupRsvpProfileEntryEach entry represents one LDP profile settings. UsdMplsGroupRsvpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1 |
usdMplsGroupRsvpProfileNameThe RSVP profile name identifies unique entry in the table. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.1 |
usdMplsGroupRsvpProfileRefreshPeriodConfigure the time out period between the generation of two refresh messages.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.2 |
usdMplsGroupRsvpProfileCleanupTimeoutFactorConfgure the number of refresh messages can be lost before PATH or RESV state is ended.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.3 |
usdMplsGroupRsvpProfileRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: usdMplsGroupRsvpProfileRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.4 |
usdMplsMajorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.2 |
usdMplsIfMajorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.2.1 |
usdMplsIfMajorNextIfIndexCoordinate ifIndex value allocation for entries in the usdMplsIfMajorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.ro UsdNextIfIndex (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.54.1.2.1.1 |
usdMplsIfMajorTableThis table contains entries for MPLS Major interfaces present in the system. SEQUENCE OF UsdMplsIfMajorEntry .1.3.6.1.4.1.4874.2.2.54.1.2.1.2 |
usdMplsIfMajorEntryEach entry describes the characteristics of an MPLS Major interface. Creating/deleting entries in this table causes corresponding entries to be created/deleted in ifTable/ifXTable/usdIfTable. UsdMplsIfMajorEntry .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1 |
usdMplsIfMajorIndexThe ifIndex of the MPLS Major interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsIfMajorNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.1 |
usdMplsIfMajorRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMajorRowStatus usdMplsIfMajorLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for usdMplsIfMajorIndex must have been determined previously, by reading usdMplsIfMajorNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created/ destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.2 |
usdMplsIfMajorLowerIfIndexThe ifIndex of an interface over which this MPLS Major interface to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.3 |
usdMplsIfMajorAdminStatusUse this object to create MPLS major interface stacked over any link layer interface. Lower layer(index) over which major stacks has to be specified for successful creation of the major interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.4 |
usdMplsIfMajorLdpAdminStatusThis object enables/disables LDP admin status on the MPLS interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.5 |
usdMplsIfMajorLdpProfileNameAll the LDP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the LDP profile name.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.6 |
usdMplsIfMajorLdpVpiStartThis object is defined to support configurations of interface label space. This configures the start range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the stop range cunncurrently.rw UsdMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.7 |
usdMplsIfMajorLdpVpiStopThis object is defined to support configurations of interface label space. This configures the stop range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the start range cunncurrently.rw UsdMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.8 |
usdMplsIfMajorLdpVciStartThis object is defined to support configurations of interface label space. This configures the start range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the stop range cunncurrently.rw UsdMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.9 |
usdMplsIfMajorLdpVciStopThis object is defined to support configurations of interface label space. This configures the stop range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the start range cunncurrently.rw UsdMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.10 |
usdMplsIfMajorRsvpAdminStatusThis object configures RSVP admin status for MPLS interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.11 |
usdMplsIfMajorRsvpProfileNameAll the RSVP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the RSVP profile name.rw DisplayString (SIZE .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.12 |
usdMplsIfMajorRsvpVpiStartThis object is defined to support configurations of interface label space. This configures the start range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the stop range cunncurrently.rw UsdMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.13 |
usdMplsIfMajorRsvpVpiStopThis object is defined to support configurations of interface label space. This configures the stop range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the start range cunncurrently.rw UsdMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.14 |
usdMplsIfMajorRsvpVciStartThis object is defined to support configurations of interface label space. This configures the start range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the stop range cunncurrently.rw UsdMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.15 |
usdMplsIfMajorRsvpVciStopThis object is defined to support configurations of interface label space. This configures the stop range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the start range cunncurrently.rw UsdMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.16 |
usdMplsIfMajorLabelSpaceTypeDisplays the label space type for the MPLS interface.ro Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.17 |
usdMplsIfMajorOpStateThis object displays MPLS major interface operation state.ro Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.18 |
usdMplsIfMajorCrLdpAdminStateThis object displays the admin state of CR-LDP.ro Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.19 |
usdMplsMinorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.3 |
usdMplsIfMinorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.3.1 |
usdMplsIfMinorNextIfIndexCoordinates ifIndex value allocation for entries in the usdMplsIfMinorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.ro UsdNextIfIndex (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.1 |
usdMplsIfMinorTableThis table contains entries for MPLS Minor interfaces present in the system. SEQUENCE OF UsdMplsIfMinorEntry .1.3.6.1.4.1.4874.2.2.54.1.3.1.2 |
usdMplsIfMinorEntryEach entry describes the characteristics of an MPLS Minor interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/usdIfTable. UsdMplsIfMinorEntry .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1 |
usdMplsIfMinorIndexThe ifIndex of the MPLS Minor interface. When creating entries in this table, suitable values for this object are determined by reading usdMplsMinorNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.1 |
usdMplsIfMinorRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMinorRowStatus usdMplsIfMinorTunnelName In addition, when creating an entry the following conditions must hold: A value for usdMplsIfMinorIndex must have been determined previously, by reading usdMplsMinorNextIfIndex. A corresponding entry in ifTable/ifXTable/usdIfTable is created/ destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.2 |
usdMplsIfMinorLowerIfIndexThe ifIndex of an interface over which this MPLS Minor interface is to be layered. A value of zero indicates no layering. As minor interface can be created without stacking on major interface, as and when it stacks on major interface by signalling protocol, it's value can be read.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.3 |
usdMplsIfMinorAdminStatusWith this object minor interface admin status can be enabled/disabled.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.4 |
usdMplsIfMinorEndpointAddressThis object configures the IP address of the tunnel destination. This object can be set along with the usdMplsIfMinorEndpointDstMask to configure the tunnel destination mask, but it is optional.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.5 |
usdMplsIfMinorEndpointDstMaskThis object configures the tunnel destination mask. It can be set along with the usdMplsIfMinorEndpointAddress.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.6 |
usdMplsIfMinorTunnelMetricModeSelect the relative or absolute mode to configure the absolute or relative tunnel metric. To set the tunnel to relative metric, usdMplsIfMinorRelativeTunnelMetric has to be set along with this object option as relative. To set the tunnel to absolute metric, usdMplsIfMinorAbsoluteTunnelMetric has to be set along with this object option as absolute.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.7 |
usdMplsIfMinorAbsoluteTunnelMetricThis object allows configuration of absolute metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.8 |
usdMplsIfMinorRelativeTunnelMetricThis object allows configuration of relative metric values. Refer to usdMplsIfMinorTunnelMetricMode for how set it.rw Integer32 (-10..10) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.9 |
usdMplsIfMinorLabelDistProtoThis object allows to select label distribution protocol. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.10 |
usdMplsIfMinorAnnounceToOspfThis object allows to register LSP endpoints to OSPF to next hop calculation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.11 |
usdMplsIfMinorAnnounceToIsisThis object allows to register LSP endpoints to IS-IS for next hop calculation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.12 |
usdMplsIfMinorAnnounceToBgpThis object allows to register LSP endpoints to BGP for next hop calculation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.13 |
usdMplsIfMinorBandwidthThis object allows configuration of bandwidth requirements for the tunnel.rw UsdMinorCfgBWRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.14 |
usdMplsIfMinorAffinityThis object allows configuration of resource class affinity for the tunnel.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.15 |
usdMplsIfMinorAffinityMaskThis allows to set the resource class affinity mask. Since it is a mask, set along with the affinity for successful configurations.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.16 |
usdMplsIfMinorSetupPriorityThis object allows configuration of preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.rw UsdMinorCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.17 |
usdMplsIfMinorHoldingPriorityThis object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.rw UsdMinorCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.18 |
usdMplsIfMinorTunnelNameThis object allows configuration of the tunnel name to be associated with tunnel settings.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.19 |
usdMplsIfMinorTunnelRetryTimesThis object allows configuration of the number of retries for tunnel setup.rw UsdMinorCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.20 |
usdMplsIfMinorTunnelRetryIntervalThis object allows configuration of retry interval for tunnel setup.rw UsdMinorCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.21 |
usdMplsIfMinorTunnelRetryTimesNorouteThis object allows configuration of the tunnel retries when no route notifications are received.rw UsdMinorCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.22 |
usdMplsIfMinorTunnelRetryIntervalNorouteThis object allows configuration of the tunnel retry interval when no route notifications are received.rw UsdMinorCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.23 |
usdMplsIfMinorBaseTunnelNameThis object allows configuration of the base tunnel name over which all the tunnels are stacked over.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.24 |
usdMplsIfMinorVpnOuiNumberThis object allows configuration of the OUI part of VPN ID.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.25 |
usdMplsIfMinorVpnIndexThis object allows configuration of the index part of VPN ID.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.26 |
usdMplsIfMinorTunnelOpStateThis object displays the tunnel operation state. established : Tunnel established teNegotiation : TE Negotiation up : Tunnel Up down : Tunnel Down cfgChanged : Tunnel config changed cfgIncEn : Tunnel incomplete Config Admin State Enable cfgIncDis : Tunnel incomplete Config Admin State Disable disabled : Tunnel disabled rel : noChange : Tunnel state no changero Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.27 |
usdMplsIfMinorTargetedDynamicTunnelConfigure targeted dynamic tunnel.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.28 |
usdMplsIfMinorReoptimizationConfigure tunnel reoptimization.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.29 |
usdMplsMinorLayerList OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.3.2 |
usdMplsIfMinorPathOptionTableTable is a list of different LSP paths as option for each LSP setup. SEQUENCE OF UsdMplsIfMinorPathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.3.2.1 |
usdMplsIfMinorPathOptionEntryEach entry represents one path option for the LSP. UsdMplsIfMinorPathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1 |
usdMplsIfMinorPathOptionIndexMinor interface uid. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.1 |
usdMplsIfMinorPathOptionNumberUnique number to identify each path option configured. Integer32 .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.2 |
usdMplsIfMinorPathOptionProtocolSelect the each path option explicit routing protocol.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.3 |
usdMplsIfMinorPathOptionLockdownEnable/disable each configured path option reoptimization.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.4 |
usdMplsIfMinorPathOptionPathNameConfigure the name for each path option.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.5 |
usdMplsIfMinorPathOptionPathIdConfigure the path option ID. Either the name or ID will be associated with a path at a time. If the path name and ID are set at a same time for the path, the name will have precedence over ID.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.6 |
usdMplsIfMinorPathOptionRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsIfMinorPathOptionRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.7 |
usdMplsTunnelProfile OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.4 |
usdMplsTunnelProfileGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.4.1 |
usdMplsTunnelProfileTableTable is a list of tunnel profiles for a given VR. SEQUENCE OF UsdMplsTunnelProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.4.1.1 |
usdMplsTunnelProfileEntryEach entry represents one tunnel profile. UsdMplsTunnelProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1 |
usdMplsTunnelProfileNameAssociate a name for the configured tunnel profile settings. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.1 |
usdMplsTunnelProfileAdminStatusEnable/disable the adminstatus of the tunnel profile.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.2 |
usdMplsTunnelProfileBaseTunnelNameConfigure the base tunnel name in tunnel profile settings. This base tunnel is the one over which all the other tunnels are stacked over. Configured base tunnel name in profile settings will be associated with the actual configured base tunnel name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.3 |
usdMplsTunnelProfileIpProfileNameConfigures the name for IP profile settings for the IP interfaces over which MPLS tunnels are stacked.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.4 |
usdMplsTunnelProfileLabelDistProtoConfigure the label distribution protocol to associate with a tunnel profile. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.5 |
usdMplsTunnelProfileAnnounceToOspfConfigure the routing protocol for next hop calculations as OSPF.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.6 |
usdMplsTunnelProfileAnnounceToIsisConfigure routing protocol for next hop calculations as ISIS.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.7 |
usdMplsTunnelProfileAnnounceToBgpConfigure routing protocol for next hop calculations as BGP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.8 |
usdMplsTunnelProfileMetricModeSelect the relative or absolute mode to configure the absolute or relative tunnel profile metric. To set the tunnel profile to relative metric, usdMplsTunnelProfileRelativeMetric has to be set along with this object option as relative. To set the tunnel profile to absolute metric, usdMplsTunnelProfileAbsoluteMetric has to be set along with this object option as absolute.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.9 |
usdMplsTunnelProfileAbsoluteMetricThis object allows configuration of the absolute metric values. Refer to usdMplsTunnelProfileMetricMode for how set it.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.10 |
usdMplsTunnelProfileRelativeMetricThis object allows configuration of the relative metric values. Refer to usdMplsTunnelProfileMetricMode for how set it.rw Integer32 (-10..10) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.11 |
usdMplsTunnelProfileBandwidthThis object allows configuration of bandwidth requirements for the tunnel.rw UsdProfileCfgBWRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.12 |
usdMplsTunnelProfileAffinityThis object allows configuration of the resource class affinity for the tunnel. This can set independently of usdMplsTunnelProfileAffinityMask.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.13 |
usdMplsTunnelProfileAffinityMaskThis allows configuration of which bits in the affinity must match the resource class bits. Can't be set independently; always with usdMplsTunnelProfileAffinity. Specify the value in bit mask format.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.14 |
usdMplsTunnelProfileSetupPriorityThis object configuration of the preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.rw UsdProfileCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.15 |
usdMplsTunnelProfileHoldingPriorityThis object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.rw UsdProfileCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.16 |
usdMplsTunnelProfileRetryTimesThis object allows configuration of the number of retries for the tunnel setup.rw UsdProfileCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.17 |
usdMplsTunnelProfileRetryIntervalThis object allows configuration of retry interval for tunnel setup.rw UsdProfileCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.18 |
usdMplsTunnelProfileRetryTimesNorouteThis object allows configuration of the tunnel retries when no route notifications are received.rw UsdProfileCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.19 |
usdMplsTunnelProfileRetryIntervalNorouteThis object allows configuration of the tunnel retry interval when no route notifications are received.rw UsdProfileCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.20 |
usdMplsTunnelProfileVpnOuiNumberThis object allows configuration of the OUI part of VPN ID.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.21 |
usdMplsTunnelProfileVpnIndexThis object allows configuration of the index part of VPN ID.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.22 |
usdMplsTunnelProfileRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfileRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.23 |
usdMplsTunnelProfileTargetedDynamicTunnelConfigure targeted dynamic tunnel.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.24 |
usdMplsTunnelProfileList OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.4.2 |
usdMplsTunnelProfilePathOptionTableTable is a list of different LSP paths as option for each LSP setup, configured as part of tunnel profile settings SEQUENCE OF UsdMplsTunnelProfilePathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.1 |
usdMplsTunnelProfilePathOptionEntryEach entry represents one path option for the LSP setup, configured as a part of tunnel profile settings. UsdMplsTunnelProfilePathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1 |
usdMplsTunnelProfileNamePathOptionName of the path option. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.1 |
usdMplsTunnelProfilePathOptionNumberUnique identifier for the path option. Integer32 .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.2 |
usdMplsTunnelProfilePathOptionProtocolPath selection option protocol.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.3 |
usdMplsTunnelProfilePathOptionLockdownEnable/disable path selection option reoptimization.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.4 |
usdMplsTunnelProfilePathOptionPathNameAssociate a name with each explicit path.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.5 |
usdMplsTunnelProfilePathOptionPathIdEach explicit path can be associated either name or ID. This object allows configuration of the ID for the explicit path.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.6 |
usdMplsTunnelProfilePathOptionRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfilePathOptionRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.7 |
usdMplsTunnelProfileDynamicEndpointTableThis table contains entries for the dynamic endpoints configured for each tunnel profile. SEQUENCE OF UsdMplsTunnelProfileDynamicEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.2 |
usdMplsTunnelProfileDynamicEndpointEntryDynamic endpoint entries for each tunnel profile. UsdMplsTunnelProfileDynamicEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1 |
usdMplsTunnelProfileNameDynamicEndpointConfigure the tunnel dynamic endpoint in tunnel profile settings. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.1 |
usdMplsTunnelProfileDynamicEndpointTypeConfigure the dynamic endpoint type for the tunnel. Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.2 |
usdMplsTunnelProfileDynamicEndpointPolicyListTypeThis object allows configuration of the dynamic tunnel policy type selection. Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.3 |
usdMplsTunnelProfileDynamicEndpointListNameThis object allows configuration of the dynamic endpoints access list name. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.4 |
usdMplsTunnelProfileDynamicEndpointRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: usdMplsTunnelProfileDynamicEndpointRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.5 |
usdMplsTunnelProfileTunnelEndpointTableTable contains list of tunnel static enpoints configured for each tunnel profile. SEQUENCE OF UsdMplsTunnelProfileTunnelEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.3 |
usdMplsTunnelProfileTunnelEndpointEntryEach entry represents one static endpoint configuration for the tunnel. UsdMplsTunnelProfileTunnelEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1 |
usdMplsTunnelProfileNameTunnelEndpointThis object configures the tunnel profile name. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.1 |
usdMplsTunnelProfileTunnelEndpointAddressThis object configures the IP address of the tunnel destination. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.2 |
usdMplsTunnelProfileTunnelEndpointDstMaskThis object configures the tunnel destination mask. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.3 |
usdMplsTunnelProfileTunnelEndpointRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdMplsTunnelProfileTunnelEndpointRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.4 |
usdMplsExplicitPath OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.5 |
usdMplsExplicitPathGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.5.1 |
usdMplsExplicitPathTableTable is a list of hops configurations for explicit paths. SEQUENCE OF UsdMplsExplicitPathEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.1 |
usdMplsExplicitPathEntryEach entry represents one hop configuration for the particular explicit path. UsdMplsExplicitPathEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1 |
usdMplsExplicitPathNameConfigure the name for the explicit path used as table index. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.1 |
usdMplsExplicitPathAdminStateEnable/disable explicit path adminstatus.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.2 |
usdMplsExplicitPathRowStatusCreation/deletion of the explicit path is done through setting this object.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.3 |
usdMplsExplicitPathNodeTableTable is a list of configured explicit paths. SEQUENCE OF UsdMplsExplicitPathNodeEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.2 |
usdMplsExplicitPathNodeEntryEach entry represents one hop in a particular explicit path. UsdMplsExplicitPathNodeEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1 |
usdMplsExplicitPathNodeNameConfigure the name for the explicit path used in the table index. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.1 |
usdMplsExplicitPathNodeIndexNumberEach explicit path hop will have an index associated with it. Configure each path hop index using this object. Integer32 .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.2 |
usdMplsExplicitPathNodeLooseConfigure the explicit path hop as strict or loose. Set along with HopAddress.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.3 |
usdMplsExplicitPathNodeHopAddressConfigure the hop IP address to setup explicit path. Explicit path next hop will be created when the mentioned hop IP address doesn't belong to any of the existing hop even without setting the rowStatus createAndGo value. The rowStatus value is used to destroy the node.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.4 |
usdMplsExplicitPathNodeHopAddressMaskConfigure the hop IP address mask. Set along with hop address.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.5 |
usdMplsExplicitPathNodeRowStatusUse this object for deletion of the node. For node creation, this value have no effect. Setting the node with IP address create the node. To delete the node set only this object.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.6 |
usdMplsConformance OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.2 |
usdMplsCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.2.1 |
usdMplsComplianceObsolete compliance statement for entities which implement the Unisphere MPLS MIB. This statement became obsolete when RowStatus support was added to some of the minor layer and tunnel profile tables.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.1.1 |
usdMplsCompliance2The compliance statement for entities which implement the Unisphere MPLS MIB. Unknown .1.3.6.1.4.1.4874.2.2.54.2.1.2 |
usdMplsConfGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.2.2 |
usdMplsLsrGlobalConfGroupA collection of objects providing management of MPLS label switching routers (LSRs) in a Unisphere product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.1 |
usdMplsMajorLayerConfGroupA collection of objects providing management of major MPLS interfaces in a Unisphere product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.2 |
usdMplsMinorLayerConfGroupObsolete collection of objects providing management of minor MPLS (tunnel) in a Unisphere product. This group became obsolete when the usdMplsIfMinorPathOptionRowStatus object was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.3 |
usdMplsTunnelProfileConfGroupObsolete collection of objects providing management of MPLS tunnel profiles in a Unisphere product. This group became obsolete when the objects usdMplsTunnelProfilePathOptionRowStatus, usdMplsTunnelProfileDynamicEndpointRowStatus and usdMplsTunnelProfileTunnelEndpointRowStatus were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.4 |
usdMplsExplicitPathConfGroupA collection of objects providing management of MPLS explicit paths in a Unisphere product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.5 |
usdMplsMinorLayerConfGroup2A collection of objects providing management of minor MPLS (tunnel) interfaces in a Unisphere product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.6 |
usdMplsTunnelProfileConfGroup2A collection of objects providing management of MPLS tunnel profiles in a Unisphere product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.7 |