Unisphere-Data-DS1-MIB
AI MIB Summary
The Unisphere-Data-DS1-MIB extends standard RFC 1406 definitions to monitor DS1 and E1 T1/E1 line interface status, performance counters, and alarm conditions on EMC Unisphere-managed storage array network ports. It enables the tracking of specific physical layer metrics such as line errors, CRC failures, and signal loss on the storage system's external network interfaces.
The DS1/E1 MIB for the Unisphere enterprise. This MIB contains managed objects to supplement those found in RFC1406 DS1/E1 MIB.
Main OID:
usdDs1MIB.1.3.6.1.4.1.4874.2.2.5
37
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
37 total| Object Name |
|---|
usdDs1MIBThe DS1/E1 MIB for the Unisphere enterprise. This MIB contains managed objects to supplement those found in RFC1406 DS1/E1 MIB. MODULE-IDENTITY .1.3.6.1.4.1.4874.2.2.5 |
usdDs1Objects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.5.1 |
usdDsx1ConfigTableThis table contains entries for DS1/E1 interfaces present in the system. SEQUENCE OF UsdDsx1ConfigEntry .1.3.6.1.4.1.4874.2.2.5.1.1 |
usdDsx1ConfigEntryEach entry describes the characteristics of an DS1/E1 interface. UsdDsx1ConfigEntry .1.3.6.1.4.1.4874.2.2.5.1.1.1 |
usdDsx1TimeSlotMapA bitmap representing the timeslots on the DS1/E1 interface that have been allocated for service. For channelized DS1/E1, set bits reflect the union of timeslot allocations across all fractional arrangements operating over this DS1/E1 interface. For unchannelized DS1/E1, all relevant timeslot bits will be set.ro UsdTimeSlotMap (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.5.1.1.1.1 |
usdDsx1Ds1ChannelNumberThis variable represents the channel number of the DS1/E1 on its parent DS3/E3. A value of 0 indicates this DS1/E1 does not have a parent DS3/E3.rw Integer32 .1.3.6.1.4.1.4874.2.2.5.1.1.1.2 |
usdDsx1CapabilitiesA value which indicates the set of capabilities of the DS1/E1 interface. The value is a sum. This sum initially takes the value zero. Then, for each capability, C, in the range 1 through 3, that this interface supports, 2 raised to (C - 1) is added to the sum. For example, an interface which is only E1 capable would have a value of 2 (2^(2-1)). In contrast, an interface which is both T1 and J1 capable would have a value of 5 (2^(1-1) + 2^(3-1)). The values for DS1/E1 interface capabilities are as follows: capability function 1 T1 2 E1 3 J1ro Integer32 .1.3.6.1.4.1.4874.2.2.5.1.1.1.3 |
usdDsx1ModeThis variable represents the DS1/E1 interface mode. The value of the usdDsx1Capabilities object for the DS1/E1 interface indicates the valid set of values for this object.rw Enumeration .1.3.6.1.4.1.4874.2.2.5.1.1.1.4 |
usdDsx1LineBuildOutCapabilitiesA value which indicates the set of line build out capabilities of the DS1/E1 interface. The value is a sum. This sum initially takes the value zero. Then, for each line build out capability, C, in the range 1 or 2, that this interface supports, 2 raised to (C - 1) is added to the sum. For example, an interface which is only short haul capable would have a value of 2 (2^(2-1)). In contrast, an interface which is both short haul and long haul capable would have a value of 3 (2^(1-1) + 2^(2-1)). The values for DS1/E1 interface line build out capabilities are as follows: line build out capability function 1 short haul 2 long haulro Integer32 .1.3.6.1.4.1.4874.2.2.5.1.1.1.5 |
usdDsx1LineBuildOutTypeThis variable represents the configured line build out type of the DS1/E1 interface. The value of the usdDsx1LineBuildOutCapabilities object for the DS1/E1 interface indicates the valid set of values for this object.rw Enumeration .1.3.6.1.4.1.4874.2.2.5.1.1.1.6 |
usdDsx1LineAttenuationThis variable represents the configured line attenuation of the DS1/E1 interface. Note that the value of this object only takes effect when the value of the usdDsx1LineBuildOutType for the DS1/E1 interface is set to longHaul(2).rw Enumeration .1.3.6.1.4.1.4874.2.2.5.1.1.1.7 |
usdDsx1LineLengthThis variable represents the length of the DS1/E1 line in meters. Note that the value of this object only takes effect when the value of the usdDsx1LineBuildOutType for the DS1/E1 interface is set to shortHaul(1).rw Integer32 .1.3.6.1.4.1.4874.2.2.5.1.1.1.8 |
usdDsx1LowerIfIndexThe ifIndex of the interface over which this Dsx1 interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.5.1.1.1.9 |
usdDsx1RowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdDsx1RowStatus usdDsx1LowerIfIndex In addition, when creating an entry the following conditions must hold: A value for ifIndex must have been determined previously, by reading usdDsx1NextIfIndex. The interface identified by usdDsx1hLowerIfIndex must exist. A corresponding entry in ifTable/ifXTable/usdIfTable is created/destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.5.1.1.1.10 |
usdDsx1SendCodeThis variable indicates what type of code is being sent across the DS1 interface by the device.rw Enumeration .1.3.6.1.4.1.4874.2.2.5.1.1.1.11 |
usdDsx1YellowAlarmThis bitmap indicates the yellow alarm settings, and is the sum of the capabilities.rw Enumeration .1.3.6.1.4.1.4874.2.2.5.1.1.1.12 |
usdDsx1RemoteLoopbackThis variable indicates the remote loopback setting.rw Enumeration .1.3.6.1.4.1.4874.2.2.5.1.1.1.13 |
usdDsx1FdlCarrierSpecifies the interface is used in carrier environment.rw Enumeration .1.3.6.1.4.1.4874.2.2.5.1.1.1.14 |
usdDsx1FdlEicThis is the equipment identification code.rw DisplayString .1.3.6.1.4.1.4874.2.2.5.1.1.1.15 |
usdDsx1FdlLicThis is the location identification code.rw DisplayString .1.3.6.1.4.1.4874.2.2.5.1.1.1.16 |
usdDsx1FdlFicThis is the frame identification code.rw DisplayString .1.3.6.1.4.1.4874.2.2.5.1.1.1.17 |
usdDsx1FdlUnitThis is the unit identification code.rw DisplayString .1.3.6.1.4.1.4874.2.2.5.1.1.1.18 |
usdDsx1FdlPfiThis is the facility identification code.rw DisplayString .1.3.6.1.4.1.4874.2.2.5.1.1.1.19 |
usdDsx1FdlPortThis is the equipment port number.rw DisplayString .1.3.6.1.4.1.4874.2.2.5.1.1.1.20 |
usdDsx1FdlGeneratorThis is the generator number.rw DisplayString .1.3.6.1.4.1.4874.2.2.5.1.1.1.21 |
usdDs1NextIfIndexCoordinate ifIndex value allocation for entries in usdDsx1ConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.ro UsdNextIfIndex (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.5.1.2 |
usdDs1Conformance OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.5.4 |
usdDs1Compliances OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.5.4.1 |
usdDs1ComplianceObsolete compliance statement for entities which implement the Unisphere DS1/E1 MIB. This statement became obsolete when new objects were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.5.4.1.1 |
usdDs1Compliance1Obsolete compliance statement for entities which implement the Unisphere DS1/E1 MIB. This statement became obsolete when dynamic DS1 interface support was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.5.4.1.2 |
usdDs1Compliance2Obsolete compliance statement for entities which implement the Unisphere DS1/E1 MIB. This statement became obsolete when FDL support was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.5.4.1.3 |
usdDs1Compliance3The compliance statement for entities which implement the Unisphere DS1/E1 MIB. Unknown .1.3.6.1.4.1.4874.2.2.5.4.1.4 |
usdDs1Groups OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.5.4.2 |
usdDs1GroupObsolete collection of objects providing management of DS1/E1 interfaces in a Unisphere product. This group became obsolete when new objects where added to the MIB.obsolete Unknown .1.3.6.1.4.1.4874.2.2.5.4.2.1 |
usdDs1Group1Obsolete collection of objects providing management of DS1/E1 interfaces in a Unisphere product. This group became obsolete when dynamic DS1 interface support was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.5.4.2.2 |
usdDs1Group2Obsolete collection of objects providing management of DS1/E1 interfaces in a Unisphere product. This group became obsolete when FDL support was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.5.4.2.3 |
usdDs1Group3A collection of objects providing management of DS1/E1 interfaces in a Unisphere product. Unknown .1.3.6.1.4.1.4874.2.2.5.4.2.4 |