UB-INTERNETWORKING-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
100
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
100 total| Object Name |
|---|
ubNode OBJECT IDENTIFIER .1.3.6.1.4.1.75 |
ubEquip OBJECT IDENTIFIER .1.3.6.1.4.1.75.1 |
ubInternetworking OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2 |
ubRISCFddiBrouter OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1 |
ubInEnc OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.1 |
encSlotsNumber of slots in the enclosurero INTEGER .1.3.6.1.4.1.75.1.2.1.1.1 |
ubInEntity OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.2 |
ubInCard OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.3 |
controlUb1 OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.3.1 |
loginASCII string with the following (case sensitive) format:
CommunityString:Passwordrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.75.1.2.1.3.1.1 |
configurationUb1 OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.3.2 |
slotNumSlot Number of this cardro INTEGER .1.3.6.1.4.1.75.1.2.1.3.2.1 |
qeContentionOwnerOwner of QE Contention in this enclosurero INTEGER .1.3.6.1.4.1.75.1.2.1.3.2.2 |
ubInPort OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.4 |
plusbus OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.4.1 |
plusbusTableStatus information and control variables for a
collection of ethernet-like interfaces attached to
a particular system. SEQUENCE OF PlusbusEntry .1.3.6.1.4.1.75.1.2.1.4.1.1 |
plusbusEntryStatus information and control variables for a
plus bus interface. PlusbusEntry .1.3.6.1.4.1.75.1.2.1.4.1.1.1 |
plusbusIndexAn index value that uniquely identifies an interface
to the plus bus. The interface
identified by a particular value of this INDEX is
the same interface as identified by the same value
of ifIndex.ro INTEGER .1.3.6.1.4.1.75.1.2.1.4.1.1.1.1 |
plusbusAdminstateThe state variable for a particular interface
The value disabled(3) signifies that transmission
and reception on the plus bus is disabled.rw Enumeration .1.3.6.1.4.1.75.1.2.1.4.1.1.1.2 |
plusbusAccessInformation configured into the bridge by
(local or network) management specifying the set of
cards from which frames may NOT be accepted via
the plusbus. Each octet within the
value of this object specifies a set of eight cards,
with the first octet specifying slots 1 through 8, the
second octet specifying slots 9 through 16, etc. Within
each octet, the most significant bit represents the
lowest numbered card, and the least significant bit
represents the highest numbered card. Thus, each card
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that card is included in the set of cards; the
card is not included if its bit has a value of '0'.
(Note that the setting of the bit corresponding to the
card being queried is irrelevant.)rw OCTET STRING .1.3.6.1.4.1.75.1.2.1.4.1.1.1.3 |
plusbusStatsTableStatistics for a collection of plus bus interfaces
attached to a particular system. SEQUENCE OF PlusbusStatsEntry .1.3.6.1.4.1.75.1.2.1.4.1.2 |
plusbusStatsEntryStatistics for a particular interface to the plus bus. PlusbusStatsEntry .1.3.6.1.4.1.75.1.2.1.4.1.2.1 |
plusbusStatsIndexAn index value that uniquely identifies an interface
to the plus bus. The interface
identified by a particular value of this INDEX
is the same interface as identified by the same
value of ifIndex.ro INTEGER .1.3.6.1.4.1.75.1.2.1.4.1.2.1.1 |
plusbusStatsTxErrorsA count of negative acknowledgements received
on transmission.ro Counter .1.3.6.1.4.1.75.1.2.1.4.1.2.1.2 |
plusbusStatsTxlostacksA count of acknowledgements not
received on transmission.ro Counter .1.3.6.1.4.1.75.1.2.1.4.1.2.1.3 |
plusbusStatsTxtimeoutsA count of bus timeouts that occurred
during transmissions.ro Counter .1.3.6.1.4.1.75.1.2.1.4.1.2.1.4 |
plusbusStatsRxErrorsA count of frames received with CRC or
frame length errorsro Counter .1.3.6.1.4.1.75.1.2.1.4.1.2.1.5 |
plusbusStatsRxtimeoutsA count of bus timeouts that occurred during
frame reception.ro Counter .1.3.6.1.4.1.75.1.2.1.4.1.2.1.6 |
plusbusStatsclocklossesA count of plusbus clock losses-detected.ro Counter .1.3.6.1.4.1.75.1.2.1.4.1.2.1.7 |
rxFifoUnderflowsro Counter .1.3.6.1.4.1.75.1.2.1.4.1.2.1.8 |
ubNVM OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.5 |
ubDownloader OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.5.1 |
ubOptions OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.5.1.1 |
ubDnloadOptionsDownload parameters. UbDnloadOptions .1.3.6.1.4.1.75.1.2.1.5.1.1.1 |
dlVersionIDVersion number of load option file
to be downloaded.ro INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.1 |
dlMaxLoadAttemptsMaximum number of load attempts
before PROM bridge becomes operational.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.2 |
dlMaxBOOTPAttemptsMaximum number of BootP attempts before
trying Rarp instead.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.3 |
dlBOOTPRetransTimeThe retransmission time between BootP
attempts.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.4 |
dlMaxRARPAttemptsMaximum number of Rarp attempts
before continuing with TFTP.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.5 |
dlRARPRetransTimeThe retransmission time between RARP
attempts.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.6 |
dlMaxTFTPAttemptsThe maximum number of times to attempt
TFTP download before initiating the PROM bridge.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.7 |
dlTFTPRetransTimeThe retransmission time between TFTP
attempts.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.1.1.8 |
ubBOOTP OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.5.1.2 |
dlBOOTPOptionsTblBootP options table. SEQUENCE OF DlBOOTPOptions .1.3.6.1.4.1.75.1.2.1.5.1.2.1 |
dlBOOTPOptionsEntryBootP options table entry. DlBOOTPOptions .1.3.6.1.4.1.75.1.2.1.5.1.2.1.1 |
dlBOOTPOptionTblEntryThe number of entries in the ubBootPOptionsTbl.ro INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.2.1.1.1 |
dlBOOTPHostNameHost name of the card for this port.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.75.1.2.1.5.1.2.1.1.2 |
dlBOOTPPortAssignTblBootP Port Assignment Table. SEQUENCE OF DlBOOTPPorts .1.3.6.1.4.1.75.1.2.1.5.1.2.2 |
dlBOOTPPortAssignEntryBOOTP Port assignment entry. DlBOOTPPorts .1.3.6.1.4.1.75.1.2.1.5.1.2.2.1 |
dlBOOTPPortIdId of port on which BootP transmissions can
be sent.ro Enumeration .1.3.6.1.4.1.75.1.2.1.5.1.2.2.1.1 |
dlBOOTPOptionsRunningThe options being run by this Port ID. This is bit mappedrw Enumeration .1.3.6.1.4.1.75.1.2.1.5.1.2.2.1.2 |
ubTFTP OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.5.1.3 |
dlTFTPOptionsTblTFTP options table. SEQUENCE OF DlTFTPOptions .1.3.6.1.4.1.75.1.2.1.5.1.3.1 |
dlTFTPOptionsEntryTFTP options table entry. DlTFTPOptions .1.3.6.1.4.1.75.1.2.1.5.1.3.1.1 |
dlTFTPOptionTblEntryThe number of entries in the ubTFTPOptionsTbl.ro INTEGER .1.3.6.1.4.1.75.1.2.1.5.1.3.1.1.1 |
dlTFTPServerIpAddrAddress of TFTP server located out this port.rw IpAddress .1.3.6.1.4.1.75.1.2.1.5.1.3.1.1.2 |
dlTFTPServerFileNamePath name of Load Information File on
download server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.75.1.2.1.5.1.3.1.1.3 |
dlTFTPPortAssignTblTFTP options table. SEQUENCE OF DlTFTPPorts .1.3.6.1.4.1.75.1.2.1.5.1.3.2 |
dlTFTPPortAssignEntryTFTP options table entry. DlTFTPPorts .1.3.6.1.4.1.75.1.2.1.5.1.3.2.1 |
dlTFTPPortIdId of port on which TFTP transmissions
can be sent.ro Enumeration .1.3.6.1.4.1.75.1.2.1.5.1.3.2.1.1 |
dlTFTPOptionsRunningBit-Mapping of Options that can be run on a given Port ID.rw Enumeration .1.3.6.1.4.1.75.1.2.1.5.1.3.2.1.2 |
ubDefaults OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.1.5.1.4 |
dlDefaultTFTPParamsDefault TFTP parameters for a device that fails BOOTP. DlDefaultTFTPParams .1.3.6.1.4.1.75.1.2.1.5.1.4.1 |
dlTFTPDefaultNodeIpAddrTFTP server default address.rw IpAddress .1.3.6.1.4.1.75.1.2.1.5.1.4.1.1 |
dlTFTPDefaultSubnetMaskTFTP server default subnet mask.rw IpAddress .1.3.6.1.4.1.75.1.2.1.5.1.4.1.2 |
dlTFTPDefaultGatewayIpAddrPath name of Load Information File on
default TFTP server.rw IpAddress .1.3.6.1.4.1.75.1.2.1.5.1.4.1.3 |
ubBridgeParamsBridge parameters. UbBridgeParams .1.3.6.1.4.1.75.1.2.1.5.2 |
ubAgingTimeThe timeout period in seconds for learning addresses
on a segment before bridge will forward packets.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.2.1 |
ubPreForwardingTimeThe timeout period in seconds for learning addresses
on a segment before bridge will forward packets.rw INTEGER .1.3.6.1.4.1.75.1.2.1.5.2.2 |
ubAppleTalkSupportrw Enumeration .1.3.6.1.4.1.75.1.2.1.5.2.3 |
ubSystemParamsSoftware Versions UbSystemParams .1.3.6.1.4.1.75.1.2.1.5.3 |
ubBroadcastPktLmtMaximum number of broadcast packets that can be
placed on the QE bus per second.rw Counter .1.3.6.1.4.1.75.1.2.1.5.3.1 |
ubUnicastPktLmtMaximum number of unicast packets that can be
placed on the QE bus per second.rw Counter .1.3.6.1.4.1.75.1.2.1.5.3.2 |
ubQuickResetrw Enumeration .1.3.6.1.4.1.75.1.2.1.5.3.3 |
ubBasePromCodeCode version number of the Base Prom (Prom 1)ro DisplayString .1.3.6.1.4.1.75.1.2.1.5.3.4 |
ubOpswPromCodeCode version number of the Operational Software
Prom (Prom 2)ro DisplayString .1.3.6.1.4.1.75.1.2.1.5.3.5 |
ubDownloadedCodeCode version of the Downloaded code running.ro DisplayString .1.3.6.1.4.1.75.1.2.1.5.3.6 |
ubRISCMPET OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.2 |
ubRISCTokenRing OBJECT IDENTIFIER .1.3.6.1.4.1.75.1.2.3 |
ubExtInternetworking OBJECT IDENTIFIER .1.3.6.1.4.1.75.2 |
ubInExt1 OBJECT IDENTIFIER .1.3.6.1.4.1.75.2.1 |
ubdot1dExt OBJECT IDENTIFIER .1.3.6.1.4.1.75.2.1.1 |
ubdot1dBaseExt OBJECT IDENTIFIER .1.3.6.1.4.1.75.2.1.1.1 |
ubdot1dAdminStateAdministrative state of bridging. If state
is disabled, no bridging will be performed,
regardless of any filtering specified in the
protocol filter table or in the forwarding database
even if the administrative state of all routing protocols
is disabledrw Enumeration .1.3.6.1.4.1.75.2.1.1.1.1 |
ubdot1dBasePortTableWidening of 'standard' dot1dBasePort table
Entries are manipulated in conjunction with
operations in the standard table. SEQUENCE OF Ubdot1dBasePortEntry .1.3.6.1.4.1.75.2.1.1.1.2 |
ubdot1dBasePortEntryA list of information for each port of the bridge. Ubdot1dBasePortEntry .1.3.6.1.4.1.75.2.1.1.1.2.1 |
ubdot1dBasePortThe port number of the port for which this entry
contains bridge management information.ro INTEGER .1.3.6.1.4.1.75.2.1.1.1.2.1.1 |
ubdot1dBasePortBlockedFramesThe number of frames discarded by this
port due to an adminstrative request to block
frames of a particular protocol type(s).ro Counter .1.3.6.1.4.1.75.2.1.1.1.2.1.2 |
ubdot1dProtocolFilterTableA table containing filtering information configured
into the bridge by (local or network) management
specifying the set of ports to which frames received
from specific ports and of specific protocol types
are allowed to be forwarded. The value of
zero in this table as the port number from which frames
with a specific destination address are received, is
used to specify all ports for which there is no
specific entry in this table for that particular
protocol type. Entries are valid for unicast and
for group/broadcast addresses. SEQUENCE OF Ubdot1dProtFiltEntry .1.3.6.1.4.1.75.2.1.1.2 |
ubdot1dProtFiltEntryFiltering information configured into the bridge by
(local or network) management specifying the set of
ports to which frames received from a specific port and
of a particular protocol type are allowed
to be forwarded. Ubdot1dProtFiltEntry .1.3.6.1.4.1.75.2.1.1.2.1 |
ubdot1dProtFiltTypeThe protocol type in a frame to which this
entry's filtering information applies.rw Enumeration .1.3.6.1.4.1.75.2.1.1.2.1.1 |
ubdot1dProtFiltReceivePortEither the value '0', or the port number of the port
from which a frame must be received in order for this
entry's filtering information to apply. A value of zero
indicates that this entry applies on all ports of the
bridge for which there is no other applicable entry.rw INTEGER .1.3.6.1.4.1.75.2.1.1.2.1.2 |
ubdot1dProtFiltAllowedToGoToThe set of ports to which frames received from a
specific port with a specific protocol type,
are allowed to be forwarded. Each octet within the
value of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8, the
second octet specifying ports 9 through 16, etc. Within
each octet, the most significant bit represents the
lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the
port is not included if its bit has a value of '0'.
(Note that the setting of the bit corresponding to the
port from which a frame is received is irrelevant.)rw OCTET STRING .1.3.6.1.4.1.75.2.1.1.2.1.3 |
ubTrapAttrs OBJECT IDENTIFIER .1.3.6.1.4.1.75.3 |
ubSystem OBJECT IDENTIFIER .1.3.6.1.4.1.75.4 |
ubProduct OBJECT IDENTIFIER .1.3.6.1.4.1.75.5 |
ubExperimental OBJECT IDENTIFIER .1.3.6.1.4.1.75.6 |
ubExpInternetworking OBJECT IDENTIFIER .1.3.6.1.4.1.75.6.2 |
ubInExp1 OBJECT IDENTIFIER .1.3.6.1.4.1.75.6.2.1 |
ubExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.75.7 |