TSMEXT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
49
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
49 total| Object Name |
|---|
tsmExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.800.2.19.1 |
IMPORTS Unknown .1.3.6.1.4.1.800.2.19.1 |
tsmAdmin OBJECT IDENTIFIER .1.3.6.1.4.1.800.2.19.1.1 |
tsmAdminPortTableTSM Port Configuration Table. SEQUENCE OF TsmAdminPortEntry .1.3.6.1.4.1.800.2.19.1.1.1 |
tsmAdminPortEntryA TSM Port Configuration Entry. TsmAdminPortEntry .1.3.6.1.4.1.800.2.19.1.1.1.1 |
tsmAdminPortSlotNumberThe slot number of the Token Ring Switching Module.ro INTEGER .1.3.6.1.4.1.800.2.19.1.1.1.1.1 |
tsmAdminPortNumberThe port number of the Token Ring Switching Module.ro INTEGER .1.3.6.1.4.1.800.2.19.1.1.1.1.2 |
tsmAdminPortStateThe configured state of the port.
1 = enable.
2 = disable.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.3 |
tsmAdminPortActiveMonThe configured active monitor participation of the port.
1 = yes.
Participate in the active monitor selection process.
2 = no.
Do NOT participate in the active monitor selection process.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.4 |
tsmAdminPortAcBitSetThe configured control mode for handling the ARI/FCI Bits of
the port.
1 = nonLocal.
Set ARI/FCI bits on all non-local LLC frames
repeated by the port. For local frames
repeat the ARI/FCI bits just as they are received.
2 = repeat.
Repeat ARI/FCI bit on all LLC frames just as
they are received.
3 = always.
Set ARI/FCI bits on all LLC frames repeated by
the port.
4 = never.
Do not set ARI/FCI bits on any LLC frames repeated by
the port.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.5 |
tsmAdminPortConfigTypeThe configured config-type of the port.
1 = auto.
Automatically set the port's ring speed, mode, duplex
and switching mode parameters.
2 = fixed.
Use customer defined values for the port's ring speed,
mode, duplex and switching mode parameters.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.6 |
tsmAdminPortRingSpeedThe configured ring speed of the port.
1 = auto.
Automatically set the port's ring speed.
2 = fourMegabit.
Always set the port's ring speed at four megabits.
3 = sixteenMegabit.
Always set the port's ring speed at sixteen megabits.
This object may ONLY be set if the value of port's
tsmAdminPortConfigType is fixed(1).rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.7 |
tsmAdminPortPortModeThe configured port mode of the port.
1 = auto.
Automatically sense the port mode. This value is set by
the switch when the tsmAdminPortConfigMode is set to auto.
This object CANNOT be changed to auto by an SNMP SET.
2 = portMode.
Only a dedicated connection to a station is supported.
3 = adapterMode.
The port operates like a station. The connection can
be either dedicated or shared.
This object may ONLY be set if the value of port's
tsmAdminPortConfigType is fixed(1).
auto(1) is NOT a valid SET value.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.8 |
tsmAdminPortDuplexThe configured duplex mode of the port.
1 = auto.
Automatically set the port's duplex mode.
2 = halfDuplex.
Alway run the port in half duplex mode.
3 = fullDuplex.
Alway run the port in full duplex mode.
This object may ONLY be set if the value of port's
tsmAdminPortConfigType is fixed(1).rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.9 |
tsmAdminPortSwModeThe configured duplex mode of the port.
1 = cutThrough.
A scheme that allows frame transmission to begin at the
output port prior to end-of-frame reception at
the input port.
2 = storeAndForward.
The entire packet is received and stored before
switching begins.
3 = adaptive.
Alternate between cut-through and store-and-forward
base on the specified error threshold.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.10 |
tsmAdminPortResetThis object is used to reset the port.
1 = ready.
The port is ready to be reset.
2 = reset.
Reset the port.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.1.1.11 |
tsmAdminSwModeTableTSM Switching Mode Configuration Table. SEQUENCE OF TsmAdminSwModeEntry .1.3.6.1.4.1.800.2.19.1.1.2 |
tsmAdminSwModeEntryA TSM Switching Mode Configuration Entry. TsmAdminSwModeEntry .1.3.6.1.4.1.800.2.19.1.1.2.1 |
tsmAdminSwModeSlotNumberThe slot number of the Token Ring Switching Module.ro INTEGER .1.3.6.1.4.1.800.2.19.1.1.2.1.1 |
tsmAdminSwModeHiErrThreshThe high error threshold in percent for all ports associated with
the TSM which are configured to run in adaptive mode. If the
percentage of errors in a sampling period meets or exceeds
this value, the port's switching mode will change from
cut-through to store-and-forward mode.rw INTEGER .1.3.6.1.4.1.800.2.19.1.1.2.1.2 |
tsmAdminSwModeLoErrThreshThe low error threshold in percent for all ports associated with
the TSM which are configured to run in adaptive mode. If the
percentage of errors in a sampling period falls below
this value, the port's switching mode will change from
store-and-forward to cut-through mode.rw INTEGER .1.3.6.1.4.1.800.2.19.1.1.2.1.3 |
tsmAdminSwModeTrendThreshThe error rate trend threshold in percent for all ports associated
with the TSM which are configured to run in adaptive mode. When the
percentage of errors is between the high and low error thresholds
AND the port is currently running in cut-through mode, the
error rate trend which is the difference in errors between
two sampling periods is compared to the error rate trend threshold.
If the error rate trend is greater than this value, the port's
switching mode will change from cut-through mode to
store-and-forward.
The error rate trend threshold should be no greater than the
difference between the high and low threshold values.rw INTEGER .1.3.6.1.4.1.800.2.19.1.1.2.1.4 |
tsmAdminSwModeSamplePeriodThe sampling period in seconds for all ports associated with the
TSM which are configured to run in adaptive mode.rw INTEGER .1.3.6.1.4.1.800.2.19.1.1.2.1.5 |
tsmAdminSwModeResetThis object is used to reset the TSM.
1 = ready.
The TSM is ready to be reset.
2 = reset.
Reset the TSM.rw Enumeration .1.3.6.1.4.1.800.2.19.1.1.2.1.6 |
tsmOper OBJECT IDENTIFIER .1.3.6.1.4.1.800.2.19.1.2 |
tsmOperPortTableTSM Port Operational Table. SEQUENCE OF TsmOperPortEntry .1.3.6.1.4.1.800.2.19.1.2.1 |
tsmOperPortEntryA TSM Port Operational Entry. TsmOperPortEntry .1.3.6.1.4.1.800.2.19.1.2.1.1 |
tsmOperPortSlotNumberThe slot number of the Token Ring Switching Module.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.1.1.1 |
tsmOperPortNumberThe port number of the Token Ring Switching Module.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.1.1.2 |
tsmOperPortStateThe operational state of the port.
1 = enable.
2 = disable.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.3 |
tsmOperPortActiveMonThe operational active monitor participation of the port.
1 = yes.
Participate in the active monitor selection process.
2 = no.
Do NOT participate in the active monitor selection process.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.4 |
tsmOperPortAcBitSetThe operational control mode for handling the ARI/FCI Bits of
the port.
1 = nonLocal.
Set ARI/FCI bits on all non-local LLC frames
repeated by the port. For local frames
repeat the ARI/FCI bits just as they are received.
2 = repeat.
Repeat ARI/FCI bit on all LLC frames just as
they are received.
3 = always.
Set ARI/FCI bits on all LLC frames repeated by
the port.
4 = never.
Do not set ARI/FCI bits on any LLC frames repeated by
the port.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.5 |
tsmOperPortConfigTypeThe operational config-type of the port.
1 = auto.
Automatically set the port's ring speed, mode and
duplex parameters.
2 = fixed.
Use customer defined values for the port's ring speed,
mode and duplex parameters.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.6 |
tsmOperPortRingSpeedThe operational ring speed of the port.
1 = auto.
The port has not yet automatically set the ring speed.
2 = fourMegabit.
3 = sixteenMegabit.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.7 |
tsmOperPortPortModeThe operational port mode of the port.
1 = auto.
Automatically sense the port mode.
2 = portMode.
Only a dedicated connection to a station is supported.
3 = adapterMode.
The port operates like a station. The connection can
be either dedicated or shared.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.8 |
tsmOperPortDuplexThe configured duplex mode of the port.
1 = auto.
The port has not yet automatically set the port's duplex mode.
2 = halfDuplex.
3 = fullDuplex.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.9 |
tsmOperPortSwModeThe configured switch mode of the port.
1 = cutThrough.
A scheme that allows frame transmission to begin at the
output port prior to end-of-frame reception at
the input port.
2 = storeAndForward.
The entire packet is received and stored before
switching begins.
3 = adaptive.
Alternate between cut-through and store-and-forward
base on the specified error threshold.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.10 |
tsmOperPortAdaptSwModeThe operational adaptive switch mode of the port.
1 = cutThrough.
A scheme that allows frame transmission to begin at the
output port prior to end-of-frame reception at
the input port.
2 = storeAndForward.
The entire packet is received and stored before
switching begins.
3 = notAdaptive.
The port is not running in adaptive mode.ro Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.11 |
tsmOperPortAdaptErrRateThe operational adaptive error rate in percent of the port.
This value is the percent of errors in the last sampling period.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.1.1.12 |
tsmOperPortAdaptTrendThe operational adaptive error rate trend in percent of the port.
This value is the difference in errors between the last two
sampling periods.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.1.1.13 |
tsmOperPortOpenStateThe operational open status of the port.
1 = opened
2 = closed
3 = opening
4 = closing
5 = openFailure
6 = ringFailurero Enumeration .1.3.6.1.4.1.800.2.19.1.2.1.1.14 |
tsmOperPortUpStreamThe operational MAC Address of the up stream neighbour
in the ring.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.800.2.19.1.2.1.1.15 |
tsmOperSwModeTableTSM Switch Mode Operational Table. SEQUENCE OF TsmOperSwModeEntry .1.3.6.1.4.1.800.2.19.1.2.2 |
tsmOperSwModeEntryA TSM Port Operational Entry. TsmOperSwModeEntry .1.3.6.1.4.1.800.2.19.1.2.2.1 |
tsmOperSwModeSlotNumberThe slot number of the Token Ring Switching Module.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.2.1.1 |
tsmOperSwModeHiErrThreshThe operational high error threshold for all ports associated with
the TSM which are configured to run in adaptive mode. If the
percentage of errors in a sampling period meets or exceeds
this value, the port's switching mode will change from
cut-through to store-and-forward mode.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.2.1.2 |
tsmOperSwModeLoErrThreshThe operational low error threshold for all ports associated with
the TSM which are configured to run in adaptive mode. If the
percentage of errors in a sampling period falls below
this value, the port's switching mode will change from
store-and-forward to cut-through mode.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.2.1.3 |
tsmOperSwModeTrendThreshThe operational error rate trend threshold in percent for all ports
associated with the TSM which are configured to run in adaptive mode.
When the percentage of errors is between the high and low error
thresholds AND the port is currently running in cut-through mode, the
error rate trend which is the difference in errors between two
sampling periods is compared to the error rate trend threshold.
If the error rate trend is greater than this value, the port's
switching mode will change from cut-through mode to
store-and-forward.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.2.1.4 |
tsmOperSwModeSamplePeriodThe operational sampling period in seconds for all ports associated
with the TSM which are configured to run in adaptive mode.ro INTEGER .1.3.6.1.4.1.800.2.19.1.2.2.1.5 |