TN-ACL-MIB
AI MIB Summary
The TN-ACL-MIB module enables the configuration and monitoring of Access Control List (ACL) policies on TN-series network modules, specifically tracking rule definitions, hit counts, and packet/byte statistics for traffic filtering enforcement.
The mib provides functionalities for ACL managing in TN modules.
Main OID:
tnAclMgmt.1.3.6.1.4.1.7483.6.3.1.1.5
117
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
117 total| Object Name |
|---|
tnAclMgmtThe mib provides functionalities for ACL managing in TN modules. MODULE-IDENTITY .1.3.6.1.4.1.7483.6.3.1.1.5 |
tnAclPortTableThis table displays and sets the ACL parameters (ACE) of each switch port. SEQUENCE OF TnAclPortEntry .1.3.6.1.4.1.7483.6.3.1.1.5.1 |
tnAclPortEntryThis entry represents an ACL port configuration. TnAclPortEntry .1.3.6.1.4.1.7483.6.3.1.1.5.1.1 |
tnAclPortPolicyIdSelect the policy to apply to this port. The allowed values are 0 through 255.
The default value is 0.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.1 |
tnAclPortActionSelect the policy to apply to this port. The allowed values are 0 through 255.
The default value is 0.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.2 |
tnAclPortRateLimiterIdSelect which rate limiter to apply on this port. The allowed values are Disabled
or the values 1 through 16. The default value is 'Disabled'.rw RateLimiterValue .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.3 |
tnAclPortEvcPolicerStateSelect whether EVC policer is enabled or disabled. The default value is 'Disabled'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.4 |
tnAclPortEvcPolicerIdSelect which EVC policer ID to apply on this port. when 'tnAclPortEvcPolicerState'
is enabled, the valid value is from 1 to 128.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.5 |
tnAclPortRedirectSelect which port frames are redirected on. The allowed values is a specific port number
and it can't be set when action is permitted. When no bit is selected, port redirect is
'disabled'.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.6 |
tnAclPortMirrorStateSpecify the mirror operation of this port. The allowed values are:
Enabled: Frames received on the port are mirrored.
Disabled: Frames received on the port are not mirrored.
The default value is 'Disabled'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.7 |
tnAclPortLoggingStateSpecify the logging operation of this port. The allowed values are:
Enabled: Frames received on the port are stored in the System Log.
Disabled: Frames received on the port are not logged.
The default value is 'Disabled'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.8 |
tnAclPortShutdownStateSpecify the port shut down operation of this port. The allowed values are:
Enabled: If a frame is received on the port, the port will be disabled.
Disabled: Port shut down is disabled.
The default value is 'Disabled'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.9 |
tnAclPortAclStateSpecify the port state of this port. The allowed values are:
Enabled: To reopen ports by changing the volatile port configuration of the ACL user module.
Disabled: To close ports by changing the volatile port configuration of the ACL user module.
The default value is 'Enabled'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.10 |
tnAclPortCounterCounts the number of frames that match this ACE.ro Counter32 .1.3.6.1.4.1.7483.6.3.1.1.5.1.1.11 |
tnAclRateLimiterTableThis table displays and sets the rate limiter for the ACL of the switch. SEQUENCE OF TnAclRateLimiterEntry .1.3.6.1.4.1.7483.6.3.1.1.5.2 |
tnAclRateLimiterEntryThis entry represents an ACL rate limiter. TnAclRateLimiterEntry .1.3.6.1.4.1.7483.6.3.1.1.5.2.1 |
tnAclRateLimitIdThe rate limiter ID for the settings contained in the same row. INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.2.1.1 |
tnAclRateLimitRateThe allowed values are: 0-3276700 in pps
or 0, 100, 200, 300, ..., 1000000 in kbps.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.2.1.2 |
tnAclRateLimitUnitSpecify the rate unit. The allowed values are:
pps: packets per second.
kbps: Kbits per second.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.2.1.3 |
tnAclOperTableThis table sets the ACL operation. SEQUENCE OF TnAclOperEntry .1.3.6.1.4.1.7483.6.3.1.1.5.3 |
tnAclOperEntryThis entry represents an ACL operation. TnAclOperEntry .1.3.6.1.4.1.7483.6.3.1.1.5.3.1 |
tnAclClearCounterSpecify ACL clear operation. The allowed values are:
nooper: no operation.
clear: Clear all ACL counters, including counts the number of frames that match this ACE
and ACL port counters.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.3.1.1 |
tnAceTableThis table contains the configuration of ACE(ACL control entry) of the switch. SEQUENCE OF TnAceEntry .1.3.6.1.4.1.7483.6.3.1.1.5.4 |
tnAceEntryThis entry represents an ACE.
Each entry in this table represents an ACE and can be created or deleted
by the management system. TnAceEntry .1.3.6.1.4.1.7483.6.3.1.1.5.4.1 |
tnAceIndexThe index of ACE. INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.1 |
tnAceNextIndexSpecify the created ACE is placed before which ACE.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.2 |
tnAceIngressPortSelect the ingress port for which this ACE applies.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.3 |
tnAcePolicyFilterTypeSpecify the policy number filter for this ACE.
Any: No policy filter is specified. (policy filter status is 'dont-care'.)
Specific: If you want to filter a specific policy with this ACE, choose this
value. Two field for entering an policy value and bitmask appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.4 |
tnAcePolicyValueWhen 'Specific' is selected for the policy filter, you can enter a specific
policy value. The allowed range is 0 to 255.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.5 |
tnAcePolicyBitMaskWhen 'Specific' is selected for the policy filter, you can enter a specific
policy bitmask. The allowed range is 0x0 to 0xff.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.6 |
tnAcePolicyFrameTypeSelect the frame type for this ACE. These frame types are mutually exclusive.
any: Any frame can match this ACE.
etherType: Only Ethernet Type frames can match this ACE. The IEEE 802.3
describes the value of Length/Type Field specifications to be
greater than or equal to 1536 decimal (equal to 0600 hexadecimal).
arp: Only ARP frames can match this ACE. Notice the ARP frames won't match the
ACE with ethernet type.
ipv4: Only IPv4 frames can match this ACE. Notice the IPv4 frames won't match
the ACE with ethernet type.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.7 |
tnAceActionSpecify the action to take with a frame that hits this ACE.
permit: The frame that hits this ACE is granted permission for the ACE operation.
deny: The frame that hits this ACE is dropped.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.8 |
tnAceRateLimiterSpecify the rate limiter in number of base units. The allowed range is 1 to 16.
'disabled' indicates that the rate limiter operation is disabled.rw RateLimiterValue .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.9 |
tnAceEvcPolicerStateSelect whether EVC policer is enabled or disabled. The default value is 'Disabled'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.10 |
tnAceEvcPolicerIdSelect which EVC policer ID to apply on this ACE. The allowed values are from 1
through 128.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.11 |
tnAcePortRedirectFrames that hit the ACE are redirected to the port number specified here. The allowed
range is the same as the switch port number range. 'disabled' indicates that the port redirect
operation is disabled and the specific port number of 'Port Redirect' can't be set when action
is permitted.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.12 |
tnAceMirrorStateSpecify the mirror operation of this port. Frames matching the ACE are mirrored to the destination
mirror port. The allowed values are:
Enabled: Frames received on the port are mirrored.
Disabled: Frames received on the port are not mirrored.
The default value is 'Disabled'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.13 |
tnAceLoggingStateSpecify the logging operation of the ACE. The allowed values are:
Enabled: Frames matching the ACE are stored in the System Log.
Disabled: Frames matching the ACE are not logged.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.14 |
tnAceShutdownStateSpecify the port shut down operation of the ACE. The allowed values are:
Enabled: If a frame matches the ACE, the ingress port will be disabled.
Disabled: Port shut down is disabled for the ACE.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.15 |
tnAceCounterThe counter indicates the number of times the ACE was hit by a frame.ro Counter32 .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.16 |
tnAceVlan8021qTaggedSpecify whether frames can hit the action according to the 802.1Q tagged. The allowed values are:
any: Any value is allowed ('dont-care').
enabled: Tagged frame only.
disabled: Untagged frame only.
The default value is 'Any'.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.17 |
tnAceVlanIdFilterSpecify the VLAN ID filter for this ACE.
any: No VLAN ID filter is specified. (VLAN ID filter status is 'dont-care'.)
specific: If you want to filter a specific VLAN ID with this ACE, choose this value. A field for
entering a VLAN ID number appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.18 |
tnAceVlanIdWhen 'Specific' is selected for the VLAN ID filter, you can enter a specific VLAN ID number.
The allowed range is 1 to 4095. A frame that hits this ACE matches this VLAN ID value.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.19 |
tnAceTagPrioritySpecify the tag priority for this ACE. A frame that hits this ACE matches this tag priority.
The allowed number range is 0 to 7. The value Any means that no tag priority is specified (tag
priority is 'dont-care').rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.20 |
tnAceRowStatusThe status of this conceptual row entry of ACE table. This object isused to manage the
creation and deletion of conceptual rows.
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.21 |
tnAceLookupSpecify the second lookup operation of the ACE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.1.5.4.1.22 |
tnAceEtherTableThis table contains the related configuration of ACE
when frame type is etherType. SEQUENCE OF TnAceEtherEntry .1.3.6.1.4.1.7483.6.3.1.1.5.5 |
tnAceEtherEntryThis entry represents an etherType related ACE configuration. TnAceEtherEntry .1.3.6.1.4.1.7483.6.3.1.1.5.5.1 |
tnAceEtherSmacFilterSpecify the source MAC filter for this ACE.
any: No SMAC filter is specified. (SMAC filter status is 'dont-care'.)
specific: If you want to filter a specific source MAC address with this ACE, choose this value.
A field for entering an SMAC value appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.5.1.1 |
tnAceEtherSmacValWhen 'Specific' is selected for the SMAC/DMAC filter, you can enter a specific value.
The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxxxxxxxx' (x is
a hexadecimal digit). A frame that hits this ACE matches this SMAC value.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.1.5.5.1.2 |
tnAceEtherDmacFilterSpecify the destination MAC filter for this ACE.
any: No DMAC filter is specified. (DMAC filter status is 'dont-care'.)
unicast: Frame must be unicast.
multicast: Frame must be multicast.
broadcast: Frame must be broadcast.
specific: If you want to filter a specific destination MAC address with this ACE,
choose this value. A field for entering a DMAC value appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.5.1.3 |
tnAceEtherDmacValWhen 'Specific' is selected for the DMAC filter, you can enter a specific value.
The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxxxxxxxx' (x is
a hexadecimal digit). A frame that hits this ACE matches this DMAC value.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.1.5.5.1.4 |
tnAceEtherTypeFilterSpecify the Ethernet type filter for this ACE:
any: No EtherType filter is specified. (EtherType filter status is 'don't-care'.
specific: If you want to filter a specific EtherType filter with this ACE, you can enter a
specific EtherType value. A field for entering a EtherType value appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.5.1.5 |
tnAceEtherTypeValWhen 'Specific' is selected for the EtherType filter, you can enter a specific EtherType value.
The allowed range is 0x600 to 0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and 0x86DD(IPv6). A
frame that hits this ACE matches this EtherType value.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.5.1.6 |
tnAceArpTableThis table contains the related configuration of ACE
when frame type is ARP. SEQUENCE OF TnAceArpEntry .1.3.6.1.4.1.7483.6.3.1.1.5.6 |
tnAceArpEntryThis entry represents an ARP related ACE configuration. TnAceArpEntry .1.3.6.1.4.1.7483.6.3.1.1.5.6.1 |
tnAceArpSmacFilterSpecify the source MAC filter for this ACE.
any: No SMAC filter is specified. (SMAC filter status is 'dont-care'.)
specific: If you want to filter a specific source MAC address with this ACE, choose this value.
A field for entering an SMAC value appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.1 |
tnAceArpSmacValWhen 'Specific' is selected for the SMAC/DMAC filter, you can enter a specific value.
The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxxxxxxxx' (x is
a hexadecimal digit). A frame that hits this ACE matches this SMAC value.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.2 |
tnAceArpDmacFilterSpecify the destination MAC filter for this ACE.
any: No DMAC filter is specified. (DMAC filter status is 'dont-care'.)
unicast: Frame must be unicast.
multicast: Frame must be multicast.
broadcast: Frame must be broadcast.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.3 |
tnAceArpParmArpRarpSpecify the available ARP/RARP opcode (OP) flag for this ACE.
any: No ARP/RARP OP flag is specified. (OP is 'dont-care'.)
arp: Frame must have ARP/RARP opcode set to ARP.
rarp: Frame must have ARP/RARP opcode set to RARP.
other: Frame has unknown ARP/RARP Opcode flag.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.4 |
tnAceArpParmRequestReplySpecify the available requset/reply opcode (OP) flag for this ACE.
any: No ARP/RARP OP flag is specified. (OP is 'dont-care'.)
request: Frame must have ARP Request or RARP Request OP flag set.
reply: Frame must have ARP Reply or RARP Reply OP flag.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.5 |
tnAceArpParmSenderIpFilterSpecify the sender IP filter for this ACE.
any: No sender filter is specified. (sender ip filter status is 'don't-care'.)
host: If you want to filter a specific host address with this ECE, choose this value. A field
for entering a host address appears.
network: If you want to filter a specific network address with this ECE, choose this value.
A Two fields for entering a specific network address and network mask appears.rw HostOrNetworkOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.6 |
tnAceArpParmSenderIpAddressWhen 'Host' or 'Network' is selected for the sender ip filter, you can enter a specific host or
network address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.7 |
tnAceArpParmSenderIpMaskWhen 'Network' is selected for the sender ip filter, you can enter a specific network mask.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.8 |
tnAceArpParmTargetIpFilterSpecify the target IP filter for this ACE.
any: No sender filter is specified. (target ip filter status is 'don't-care'.)
host: If you want to filter a specific host address with this ECE, choose this value. A field
for entering a host address appears.
network: If you want to filter a specific network address with this ECE, choose this value.
A Two fields for entering a specific network address and network mask appears.rw HostOrNetworkOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.9 |
tnAceArpParmTargetIpAddressWhen 'Host' or 'Network' is selected for the target ip filter, you can enter a specific host or
network address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.10 |
tnAceArpParmTargetIpMaskWhen 'Network' is selected for the target ip filter, you can enter a specific network mask.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.11 |
tnAceArpSenderMacMatchSpecify whether frames can hit the action according to their sender hardware address field (SHA) settings.
0: ARP frames where SHA is not equal to the SMAC address.
1: ARP frames where SHA is equal to the SMAC address.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.12 |
tnAceArpRarpTargetMacMatchSpecify whether frames can hit the action according to their target hardware address field (THA) settings.
0: RARP frames where THA is not equal to the SMAC address.
1: RARP frames where THA is equal to the SMAC address.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.13 |
tnAceArpIpEthernetLengthSpecify whether frames can hit the action according to their ARP/RARP hardware address length (HLN) and protocol
address length (PLN) settings.
0: ARP/RARP frames where the HLN is not equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04).
1: ARP/RARP frames where the HLN is equal to Ethernet (0x06) and the (PLN) is equal to IPv4 (0x04).
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.14 |
tnAceArpIpSpecify whether frames can hit the action according to their ARP/RARP hardware address space (HRD) settings.
0: ARP/RARP frames where the HLD is not equal to Ethernet (1).
1: ARP/RARP frames where the HLD is equal to Ethernet (1).
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.15 |
tnAceArpEthernetSpecify whether frames can hit the action according to their ARP/RARP protocol address space (PRO) settings.
0: ARP/RARP frames where the PRO is not equal to IP (0x800).
1: ARP/RARP frames where the PRO is equal to IP (0x800).
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.6.1.16 |
tnAceIpv4TableThis table contains the related configuration of ACE
when frame type is IPv4. SEQUENCE OF TnAceIpv4Entry .1.3.6.1.4.1.7483.6.3.1.1.5.7 |
tnAceIpv4EntryThis entry represents an IPv4 related ACE configuration. TnAceIpv4Entry .1.3.6.1.4.1.7483.6.3.1.1.5.7.1 |
tnAceIpv4ProtoFilterSpecify the IP protocol filter for this ACE.
any: No IP protocol filter is specified. (Protocol filter status is 'don't-care'.)
other: If you want to filter a specific IP protocol filter with this ACE, choose this value.
A field for entering an IP protocol filter appears.
icmp: Select ICMP to filter IPv4 ICMP protocol frames. Extra fields for defining ICMP parameters
will appear. These fields are explained later in this help file.
udp: Select UDP to filter IPv4 UDP protocol frames. Extra fields for defining UDP parameters will
appear. These fields are explained later in this help file.
tcp: Select TCP to filter IPv4 TCP protocol frames. Extra fields for defining TCP parameters will
appear. These fields are explained later in this help file.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.1 |
tnAceIpv4ProtoValueWhen 'Specific' is selected for the IP protocol value, you can enter a specific value. The allowed
range is 0 to 255. A frame that hits this ACE matches this IP protocol value.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.2 |
tnAceIpv4TtlSpecify the Time-to-Live settings for this ACE.
zero: IPv4 frames with a Time-to-Live field greater than zero must not be able to match this entry.
nonZero: IPv4 frames with a Time-to-Live field greater than zero must be able to match this entry.
any: Any value is allowed ('don't-care').rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.3 |
tnAceIpv4FragmentSpecify the fragment offset settings for this ACE. This involves the settings for the More Fragments (MF)
bit and the Fragment Offset (FRAG OFFSET) field for an IPv4 frame.
any: Any value is allowed ('don't-care').
yes: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must be able to
match this entry.
no: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must not be able
to match this entry.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.4 |
tnAceIpv4OptionSpecify the options flag setting for this ACE.
any: Any value is allowed ('don't-care').
yes: IPv4 frames where the options flag is set must be able to match this entry.
no: IPv4 frames where the options flag is set must not be able to match this entry.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.5 |
tnAceIpv4SipFilterSpecify the source IP filter for this ACE.
any: No source IP filter is specified. (source ip filter is 'don't-care'.)
host: Source IP filter is set to Host. Specify the source IP address in the SIP Address field that appears.
network: Source IP filter is set to Network. Specify the source IP address and source IP mask in the SIP
Address and SIP Mask fields that appear.rw HostOrNetworkOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.6 |
tnAceIpv4SipAddressWhen 'Host' or 'Network' is selected for the source ip filter, you can enter a specific host or
network address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.7 |
tnAceIpv4SipMaskWhen 'Network' is selected for the source ip filter, you can enter a specific network mask.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.8 |
tnAceIpv4DipFilterSpecify the destination IP filter for this ACE.
any: No destination IP filter is specified. (source ip filter is 'don't-care'.)
host: Destination IP filter is set to Host. Specify the destination IP address in the SIP Address field that appears.
network: Destination IP filter is set to Network. Specify the destination IP address and source IP mask in the DIP
Address and DIP Mask fields that appear.rw HostOrNetworkOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.9 |
tnAceIpv4DipAddressWhen 'Host' or 'Network' is selected for the destination ip filter, you can enter a specific host or
network address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.10 |
tnAceIpv4DipMaskWhen 'Network' is selected for the destination ip filter, you can enter a specific network mask.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.11 |
tnAceIpv4IcmpTypeFilterSpecify the ICMP filter for this ACE.
any: No ICMP filter is specified. (ICMP filter status is 'dont-care'.)
specific: If you want to filter a specific ICMP filter with this ACE, you can enter a specific ICMP value.
A field for entering an ICMP value appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.12 |
tnAceIpv4IcmpTypeValueWhen 'Specific' is selected for the ICMP filter, you can enter a specific ICMP value. The allowed range is
0 to 255. A frame that hits this ACE matches this ICMP value.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.13 |
tnAceIpv4IcmpCodeFilterSpecify the ICMP code filter for this ACE.
any: No ICMP code is specified. (ICMP filter status is 'dont-care'.)
specific: If you want to filter a specific ICMP code filter with this ACE, you can enter a specific ICMP
code value. A field for entering an ICMP code value appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.14 |
tnAceIpv4IcmpCodeValueWhen 'Specific' is selected for the ICMP code filter, you can enter a specific ICMP code value. The allowed
range is 0 to 255. A frame that hits this ACE matches this ICMP code value.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.15 |
tnAceIPv4SrcPortFilterTypeThe TCP/UDP source port for matching the ACE. It only significant if protocol
filter 'UDP' or 'TCP' is selected. The possible values are:
any: No TCP/UDP source port filter is specified. (Source port filter status is 'don't-care'.)
specific: If you want to filter a specific TCP/UDP source port No. with this ACE, choose this value.
A field for entering a specific source port No. appears.
range: If you want to filter a specific TCP/UDP source port range filter with this ACE, choose
this value. A field for entering a range appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.16 |
tnAceIPv4SrcPortFilterNoWhen 'Specific' is selected for the source port filter, you can enter a specific value.
The allowed value is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.17 |
tnAceIPv4SrcPortRangeStartWhen 'Range' is selected for the source port filter, you can enter a specific range.
The allowed range start is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.18 |
tnAceIPv4SrcPortRangeEndWhen 'Range' is selected for the source port filter, you can enter a specific range.
The allowed range end is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.19 |
tnAceIPv4DstPortFilterTypeThe TCP/UDP destination port for matching the ACE. It only significant if protocol
filter 'UDP' or 'TCP' is selected. The possible values are:
any: No TCP/UDP destination port filter is specified. (Destination port filter status is 'don't-care'.)
specific: If you want to filter a specific TCP/UDP destination port No. with this ACE, choose this value.
A field for entering a specific No. appears.
range: If you want to filter a specific TCP/UDP destination port range filter with this ACE, choose
this value. A field for entering a range appears.rw Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.20 |
tnAceIPv4DstPortFilterNoWhen 'Specific' is selected for the destination port filter, you can enter a specific value.
The allowed value is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.21 |
tnAceIPv4DstPortRangeStartWhen 'Range' is selected for the destination port filter, you can enter a specific range.
The allowed range start is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.22 |
tnAceIPv4DstPortRangeEndWhen 'Range' is selected for the destination port filter, you can enter a specific range.
The allowed range end is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.23 |
tnAceIPv4TcpFinSpecify the TCP 'No more data from sender' (FIN) value for this ACE.
0: TCP frames where the FIN field is set must not be able to match this entry.
1: TCP frames where the FIN field is set must be able to match this entry.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.24 |
tnAceIPv4TcpSynSpecify the TCP 'Synchronize sequence numbers' (SYN) value for this ACE.
0: TCP frames where the SYN field is set must not be able to match this entry.
1: TCP frames where the SYN field is set must be able to match this entry.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.25 |
tnAceIPv4TcpRstSpecify the TCP 'Reset the connection' (RST) value for this ACE.
0: TCP frames where the RST field is set must not be able to match this entry.
1: TCP frames where the RST field is set must be able to match this entry.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.26 |
tnAceIPv4TcpPshSpecify the TCP 'Push Function' (PSH) value for this ACE.
0: TCP frames where the PSH field is set must not be able to match this entry.
1: TCP frames where the PSH field is set must be able to match this entry.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.27 |
tnAceIPv4TcpAckSpecify the TCP 'Acknowledgment field significant' (ACK) value for this ACE.
0: TCP frames where the ACK field is set must not be able to match this entry.
1: TCP frames where the ACK field is set must be able to match this entry.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.28 |
tnAceIPv4TcpUrgSpecify the TCP 'Urgent Pointer field significant' (URG) value for this ACE.
0: TCP frames where the URG field is set must not be able to match this entry.
1: TCP frames where the URG field is set must be able to match this entry.
Any: Any value is allowed ('dont-care').rw TruthValueOrAny .1.3.6.1.4.1.7483.6.3.1.1.5.7.1.29 |
tnAclStatusTableThis table shows the ACL status by different ACL users.
Each row describes the ACE that is defined. It is a
conflict if a specific ACE is not applied to the hardware
due to hardware limitations. The maximum number of ACEs
is 256 on each switch. SEQUENCE OF TnAclStatusEntry .1.3.6.1.4.1.7483.6.3.1.1.5.8 |
tnAclStatusEntryThis entry represents ACL status by different ACL users. TnAclStatusEntry .1.3.6.1.4.1.7483.6.3.1.1.5.8.1 |
tnAclStatusUserIndicates the ACL user. Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.1 |
tnAclStatusIngressPortIndicates the ingress port of the ACE. Possible values are:
All: The ACE will match all ingress port.
Port: The ACE will match a specific ingress port.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.2 |
tnAclStatusFrameTypeIndicates the frame type of the ACE. Possible values are:
Any: The ACE will match any frame type.
EType: The ACE will match Ethernet Type frames. Note that
an Ethernet Type based ACE will not get matched by IP and ARP frames.
ARP: The ACE will match ARP/RARP frames.
IPv4: The ACE will match all IPv4 frames.
IPv4/ICMP: The ACE will match IPv4 frames with ICMP protocol.
IPv4/UDP: The ACE will match IPv4 frames with UDP protocol.
IPv4/TCP: The ACE will match IPv4 frames with TCP protocol.
IPv4/Other: The ACE will match IPv4 frames, which are not ICMP/UDP/TCP.
IPv6: The ACE will match all IPv6 standard frames.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.3 |
tnAclStatusEtypeValIndicates the type value when frame type of the ACE is Ethernet Type.ro INTEGER .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.4 |
tnAclStatusActionIndicates the forwarding action of the ACE.
Permit: Frames matching the ACE may be forwarded and learned.
Deny: Frames matching the ACE are dropped.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.5 |
tnAclStatusRateLimiterIndicates the rate limiter number of the ACE.
The allowed range is 1 to 16. When Disabled is
displayed, the rate limiter operation is disabled.ro RateLimiterValue .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.6 |
tnAclStatusPortRedirectIndicates the port redirect operation of the ACE.
Frames matching the ACE are redirected to the port
number. The allowed values are Disabled or a specific
port number. When Disabled is displayed, the port
redirect operation is disabled.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.7 |
tnAclStatusMirrorSpecify the mirror operation of this port. The allowed values are:
Enabled: Frames received on the port are mirrored.
Disabled: Frames received on the port are not mirrored.
The default value is 'Disabled'.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.8 |
tnAclStatusCpuForward packet that matched the specific ACE to CPU.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.9 |
tnAclStatusCpuOnceForward first packet that matched the specific ACE to CPU.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.10 |
tnAclStatusCounterThe counter indicates the number of times the ACE was hit by a frame.ro Counter32 .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.11 |
tnAclStatusConflictIndicates the hardware status of the specific
ACE. The specific ACE is not applied to the
hardware due to hardware limitations.ro Enumeration .1.3.6.1.4.1.7483.6.3.1.1.5.8.1.12 |