TIARA-V35-MIB
AI MIB Summary
The TIARA-V35-MIB facilitates the monitoring and management of Tiara Networks V.35 serial interface modules, specifically tracking physical layer status, interface statistics, and V.35 protocol state transitions for legacy WAN connectivity.
MIB definitions for Tiara V35 module.
Main OID:
tiaraV35Mib.1.3.6.1.4.1.3174.2.7.3
24
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
24 total| Object Name |
|---|
tiaraV35MibMIB definitions for Tiara V35 module. MODULE-IDENTITY .1.3.6.1.4.1.3174.2.7.3 |
v35ConfigTableTiara Networks V35 interface-related configurable parameters are listed in this table. SEQUENCE OF V35ConfigTableEntry .1.3.6.1.4.1.3174.2.7.3.1 |
v35ConfigTableEntryV35 table entry. V35ConfigTableEntry .1.3.6.1.4.1.3174.2.7.3.1.1 |
v35IfIndexAn integer value that is an index in the entries of the ifTable (MIB-II) with a V.35 interface type. INTEGER .1.3.6.1.4.1.3174.2.7.3.1.1.1 |
v35ConfigClockRateConfigures the clock rate for V35.rw Integer32(1000000 .. 8000000) .1.3.6.1.4.1.3174.2.7.3.1.1.2 |
v35ConfigClockSourceConfigures the clock source for V35. It can be either internal or line.rw Enumeration .1.3.6.1.4.1.3174.2.7.3.1.1.3 |
v35ConfigModeConfigures the mode for V35 to be either dce or dte.rw Enumeration .1.3.6.1.4.1.3174.2.7.3.1.1.4 |
v35ConfigCRCConfigures the cyclic redundancy check for V35 to be either 16 or 32 bits.rw Enumeration .1.3.6.1.4.1.3174.2.7.3.1.1.5 |
v35ConfigDataModeConfigures the data for V.35 to be either normal or inverted.rw Enumeration .1.3.6.1.4.1.3174.2.7.3.1.1.6 |
v35ConfigFlowControlConfigures the hardware flow control for V.35 to be either on or off.rw Enumeration .1.3.6.1.4.1.3174.2.7.3.1.1.7 |
v35StatsTableTiara Networks V35 interface-related status variables are listed in this table. SEQUENCE OF V35StatsTableEntry .1.3.6.1.4.1.3174.2.7.3.2 |
v35StatsTableEntryV35 statistics table entry. V35StatsTableEntry .1.3.6.1.4.1.3174.2.7.3.2.1 |
v35StatsAlarmStatusSpecifies the status of the V35 alarm. If the bit is set, it indicates that the alarm state is on. Alarm bits are mode dependent; they are interpreted as follows: v35-alarms-DTR - DTR not received from DTE (V.35 is DCE) v35-alarms-DSR - DSR not received from DCE (V.35 is DTE) v35-alarms-ST - V.35 adaptor driving ST (V.35 is DCE) v35-alarms-CTS - CTS not received from DCE (V.35 is DTE) v35-alarms-RTS - RTS not received from DTE (V.35 is DCE)ro Bits .1.3.6.1.4.1.3174.2.7.3.2.1.1 |
v35StatsFramesInSpecifies the number of incoming frames.ro Counter32 .1.3.6.1.4.1.3174.2.7.3.2.1.2 |
v35StatsFramesOutSpecifies the number of outgoing frames.ro Counter32 .1.3.6.1.4.1.3174.2.7.3.2.1.3 |
v35StatsOctetsInSpecifies the number of incoming octets.ro Counter32 .1.3.6.1.4.1.3174.2.7.3.2.1.4 |
v35StatsOctetsOutSpecifies the number of outgoing octets.ro Counter32 .1.3.6.1.4.1.3174.2.7.3.2.1.5 |
v35StatsCRCErrorsSpecifies the number of CRC errors that have been identified so far.ro Counter32 .1.3.6.1.4.1.3174.2.7.3.2.1.6 |
v35Traps OBJECT IDENTIFIER .1.3.6.1.4.1.3174.2.7.3.3 |
v35AlarmOnTrapV35 alarm traps for the Alarm On state. NOTIFICATION-TYPE .1.3.6.1.4.1.3174.2.7.3.3.0.1 |
v35AlarmOffTrapV35 alarm traps for the Alarm Off state. NOTIFICATION-TYPE .1.3.6.1.4.1.3174.2.7.3.3.0.2 |
v35TrapVariables OBJECT IDENTIFIER .1.3.6.1.4.1.3174.2.7.3.3.1 |
v35SlotNumberThis V35 trap variable specifies the slot number of the V35 interface. INTEGER .1.3.6.1.4.1.3174.2.7.3.3.1.1 |
v35AlarmTypeThis V35 alarm type specifies the type of the alarm trap generated by the agent for the V35 interface. Alarm bits are mode dependent; they are interpreted as follows: v35-alarms-DTR - DTR not received from DTE (V.35 is DCE) v35-alarms-DSR - DSR not received from DCE (V.35 is DTE) v35-alarms-ST - V.35 adaptor driving ST (V.35 is DCE) v35-alarms-CTS - CTS not received from DCE (V.35 is DTE) v35-alarms-RTS - RTS not received from DTE (V.35 is DCE) Enumeration .1.3.6.1.4.1.3174.2.7.3.3.1.2 |