TIARA-HSSI-MIB
The TIARA-HSSI-MIB provides management definitions for Tiara Networks HSSI (High-Speed Serial Interface) modules, enabling monitoring of physical layer status, interface statistics, and HSSI-specific protocol states. It facilitates the tracking of link up/down events, error counters, and throughput metrics for high-speed serial connections on Tiara hardware.
Imported Objects
Objects
27 total| Object Name |
|---|
tiaraHssiMibMIB definitions for Tiara HSSI modules. MODULE-IDENTITY .1.3.6.1.4.1.3174.2.7.2 |
hssiConfigTableThe HSSI interface configurable parameters are listed in this table. SEQUENCE OF HssiConfigTableEntry .1.3.6.1.4.1.3174.2.7.2.1 |
hssiConfigTableEntryHSSI table entry. HssiConfigTableEntry .1.3.6.1.4.1.3174.2.7.2.1.1 |
hssiIfIndexAn integer value that is an index in the entries of the ifTable (MIB-II) with a HSSI interface type. INTEGER .1.3.6.1.4.1.3174.2.7.2.1.1.1 |
hssiConfigClockRateConfigures the clock rate (in Hertz) for the HSSI interface.rw Integer32(1000000 .. 52000000) .1.3.6.1.4.1.3174.2.7.2.1.1.2 |
hssiConfigClockSourceConfigures the clock source for the HSSI interface to either internal or line.rw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.3 |
hssiConfigTxClockSourceConfigures the transmit clock source for the HSSI interface to either internal or terminal. This variable is valid only for the HSSI interface on the USSI card.rw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.4 |
hssiConfigRxClockSourceConfigures the receive clock source for the HSSI interface to either internal or terminal. This variable is valid only for the HSSI interface on the USSI cardrw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.5 |
hssiConfigModeConfigures the mode for the HSSI to either DCE or DTE.rw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.6 |
hssiConfigDataModeConfigures the data mode for the HSSI interface. This variable is valid only for the HSSI interface on the USSI card.rw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.7 |
hssiConfigCRCConfigures the cyclic redundancy check for the HSSI interface to either 16 or 32 bits.rw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.8 |
hssiConfigProcessCtrlSignalConfigures the processing of control signals (CA/TA) for the HSSI interface. This variable is valid only for the HSSI interface on the USSI card.rw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.9 |
hssiDteLoopbackConfigures the local DTE for loopback operation: TRUE : request local DTE to go into line loopback FALSE : request local DTE to abandon line loopback These commands are valid only if the HSSI adaptor is in DCE mode and connected to a local DTE. Since the local DTE has a greater loopback priority than the local DCE, a loopback request initiated by the DCE will be ignored if the DTE simultaneously requests the DCE to loopback. Similarly, the DTE will abort a loopback already initiated by the DCE when the DTE requests the DCE to loopback.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3174.2.7.2.1.1.10 |
hssiDceLoopbackTestConfigures the local/remote DCE for loopback operation. Three DCE loopback modes are available: line, cable, and remote. Use noTest to abandon any of the DCE loopbacks. If the DCE is already in any one of the loopback modes, then noTest must be issued to abort the current test before initiating another loopback request. These commands are valid only if the HSSI adaptor is in DTE mode and it connected to a DCE.rw Enumeration .1.3.6.1.4.1.3174.2.7.2.1.1.11 |
hssiTraps OBJECT IDENTIFIER .1.3.6.1.4.1.3174.2.7.2.2 |
hssiAlarmOnTrapHSSI alarm traps for the Alarm-On state. NOTIFICATION-TYPE .1.3.6.1.4.1.3174.2.7.2.2.0.1 |
hssiAlarmOffTrapHSSI alarm traps for the Alarm-Off state. NOTIFICATION-TYPE .1.3.6.1.4.1.3174.2.7.2.2.0.2 |
hssiTrapVariables OBJECT IDENTIFIER .1.3.6.1.4.1.3174.2.7.2.2.1 |
hssiAlarmTypeSpecifies the type of alarm generated by the agent for the HSSI interface. Alarms are mode dependent; they are interpreted as follows: hssi-alarms-CA - CA not received from DCE (HSSI is DTE) hssi-alarms-ST - HSSI adaptor driving ST (HSSI is DCE) hssi-alarms-TM - TM received from DCE (HSSI is DTE) hssi-alarms-LC - HSSI adaptor detects LC (HSSI is DTE) hssi-alarms-LC - HSSI adaptor driving LC (HSSI is DCE) hssi-alarms-TA - TA not received from DTE (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor detects LA and/or LB (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor driving LA and/or LB (HSSI is DTE) Enumeration .1.3.6.1.4.1.3174.2.7.2.2.1.1 |
hssiStatsTableThe HSSI interface status parameters are listed in this table. SEQUENCE OF HssiStatsTableEntry .1.3.6.1.4.1.3174.2.7.2.3 |
hssiStatsTableEntryHSSI Statistics table entry. HssiStatsTableEntry .1.3.6.1.4.1.3174.2.7.2.3.1 |
hssiStatsAlarmStatusSpecifies the status of the HSSI alarm. If the particular bit is set, then it indicates that the alarm is in ON state. Alarm bits are mode dependent; they are interpreted as follows: hssi-alarms-CA - CA not received from DCE (HSSI is DTE) hssi-alarms-ST - HSSI adaptor driving ST (HSSI is DCE) hssi-alarms-TM - TM received from DCE (HSSI is DTE) hssi-alarms-LC - HSSI adaptor detects LC (HSSI is DTE) hssi-alarms-LC - HSSI adaptor driving LC (HSSI is DCE) hssi-alarms-TA - TA not received from DTE (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor detects LA and/or LB (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor driving LA and/or LB (HSSI is DTE)ro Bits .1.3.6.1.4.1.3174.2.7.2.3.1.1 |
hssiStatsFramesInSpecifies the number of incoming frames.ro Counter32 .1.3.6.1.4.1.3174.2.7.2.3.1.2 |
hssiStatsFramesOutSpecifies the number of outgoing frames.ro Counter32 .1.3.6.1.4.1.3174.2.7.2.3.1.3 |
hssiStatsOctetsInSpecifies the number of incoming octets.ro Counter32 .1.3.6.1.4.1.3174.2.7.2.3.1.4 |
hssiStatsOctetsOutSpecifies the number of outgoing octets.ro Counter32 .1.3.6.1.4.1.3174.2.7.2.3.1.5 |
hssiStatsCRCErrorsSpecifies the number of CRC errors that have been identified.ro Counter32 .1.3.6.1.4.1.3174.2.7.2.3.1.6 |
More MIBs from Tiara
Browse all TiaraMIBs →The TIARA-NETWORKS-DSX-TE1-MIB provides SNMP management definitions for Tiara Networks DSX T1/E1 interface modules, enabling the monitoring of physical layer statistics including line status, error counts (CRC, slips, framing errors), and interface utilization metrics.
The TIARA-NETWORKS-DSX-TE3-MIB provides SNMP management definitions for Tiara Networks DSX T3/E3 interface modules, enabling the monitoring of physical layer interface states, traffic counters, and error statistics specific to T3 and E3 digital signal cross-connect hardware.
The TIARA-FR-MIB enables monitoring and management of Frame Relay interfaces, virtual circuits, and associated traffic statistics on Tiara Network Inc. hardware. It provides specific counters for PVC status, data transmission errors, and bandwidth utilization to facilitate troubleshooting of legacy WAN connectivity.
The TIARA-NETWORKS-SYSTEM-MIB provides standard SNMP system group functionality for Tiara Networks hardware, enabling the monitoring of core device attributes such as system uptime, contact information, location, and operational status. This module facilitates the collection of fundamental management data required for inventory tracking, fault detection, and baseline performance analysis across Tiara routing and switching platforms.
The TIARARIP-MIB provides vendor-specific monitoring and management capabilities for Tiara Networks routing devices, specifically exposing metrics related to the Routing Information Protocol (RIP) such as neighbor adjacencies, route tables, and protocol state transitions.
The TIARA-PACKETFILTER-MIB provides SNMP management interfaces for Tiara Networks packet filtering appliances, enabling the monitoring of filter rule statistics, packet match counters, and dropped traffic events. It facilitates the retrieval of real-time firewall policy performance metrics and session state data to support network traffic analysis and security auditing.