TELECOM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TELECOM-MIB.
200
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
200 total| Object Name |
|---|
ppc OBJECT IDENTIFIER .1.3.6.1.4.1.935 |
SNMPv2-TCThis data type is a non-zero and non-negative value. INTEGER .1.3.6.1.4.1.935 |
device OBJECT IDENTIFIER .1.3.6.1.4.1.935.10 |
matAgent OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2 |
matObjects OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.1 |
matController OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.1.1 |
matConSerialNumController serial number.ro DisplayString ( SIZE ( 0 .. 15 ) ) .1.3.6.1.4.1.935.10.2.1.1.1 |
matConNamePower system name.ro DisplayString ( SIZE ( 0 .. 31 ) ) .1.3.6.1.4.1.935.10.2.1.1.2 |
matConWarningStateThe values indicate the unrestored traps.
For example,
if 'Controller Battery Low' and 'Controller temperature High'
the agent send
the trap 85 and trap 87 to
NMS,
so the value of matConWarningState should be '85,87'.
And then the two events restored, the value of matConWarningState
should change to empty.ro DisplayString ( SIZE ( 0 .. 31 ) ) .1.3.6.1.4.1.935.10.2.1.1.3 |
matConTemperatureTemperature of the controller, the unit is 0.1 degree.ro INTEGER .1.3.6.1.4.1.935.10.2.1.1.4 |
matAgentSoftwareVerisonThe Network Management Card software/firmware version.ro DisplayString ( SIZE ( 0 .. 31 ) ) .1.3.6.1.4.1.935.10.2.1.1.5 |
matInverter OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.1.2 |
matInvModuleNumThe number of Inverter modules.ro INTEGER .1.3.6.1.4.1.935.10.2.1.2.1 |
matInvTableThis table list Inverter message. SEQUENCE OF MATInvEntry .1.3.6.1.4.1.935.10.2.1.2.2 |
matInvEntryAn entry containing information applicable to a particular Inverter module. MATInvEntry .1.3.6.1.4.1.935.10.2.1.2.2.1 |
matInvModuleIndexThe index of Inverter module. PositiveInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.1 |
matInvSerialNumModule serial number.ro DisplayString ( SIZE ( 0 .. 15 ) ) .1.3.6.1.4.1.935.10.2.1.2.2.1.2 |
matInvFirmwareVersionFirmware version.ro DisplayString ( SIZE ( 0 .. 7 ) ) .1.3.6.1.4.1.935.10.2.1.2.2.1.3 |
matInvHardwareVersionHardware version.ro DisplayString ( SIZE ( 0 .. 7 ) ) .1.3.6.1.4.1.935.10.2.1.2.2.1.4 |
matInvWarningStateThe values indicate the unrestored traps.
For example,
if 'Inverter fault' and 'Inverter Over-loading'
the agent send
the trap 1 and trap 3 to
NMS,
so the value of matConWarningState should be '1,3'.
And then the two events restored, the value of matConWarningState
should change to empty.ro DisplayString ( SIZE ( 0 .. 63 ) ) .1.3.6.1.4.1.935.10.2.1.2.2.1.5 |
matInvOutputVoltageInverter Output Voltage, the unit is 0.1 Volt.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.6 |
matInvOutputCurrentInverter Output Current, unit is 0.1 amp.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.7 |
matInvBatteryVoltageInverter Battery voltage, the unit is 0.1 Volt.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.8 |
matInvOutputFreqOutput frequency, the unit is 0.1 Hz.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.9 |
matInvOutputPowerOutput power, the unit is VA.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.10 |
matInvPowerLimitPower Limit Status of Inverter module, the unit is percent.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.11 |
matInvRunTimeRun time, the unit is Hour.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.12 |
matInvTemperatureTemperature of the inverter, the unit is 0.1 degree.ro INTEGER .1.3.6.1.4.1.935.10.2.1.2.2.1.13 |
matInvLineVoltageLine voltage of 3.5K, the unit is 0.1 Volt.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.14 |
matInvLineFreqLine frequency of 3.5K, the unit is 0.1 Hz.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.15 |
matInvMbsPositionMBS position of 3.5K.ro Enumeration .1.3.6.1.4.1.935.10.2.1.2.2.1.16 |
matInvRunModeCurrently run mode of 3.5K.ro Enumeration .1.3.6.1.4.1.935.10.2.1.2.2.1.17 |
matInvPriorityPriority of 3.5K.ro Enumeration .1.3.6.1.4.1.935.10.2.1.2.2.1.18 |
matConfInvOutputVoltageRating Output voltage, the unit is 0.1 Volt.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.19 |
matConfInvInputVoltageRating Input voltage, the unit is 0.1 Volt.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.20 |
matConfInvOutputVoltHighLossOutput High Loss voltage, the unit is 0.1 Volt.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.21 |
matConfInvOutputVoltLowLossOutput Low loss voltage, the unit is 0.1 Volt.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.22 |
matConfInvOutputPowerRating output power, the unit is VA.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.23 |
matConfInvOutputFreqRating output frequency, the unit is 0.1 Hz.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.2.2.1.24 |
matInvPhaseTypePhase type.ro Enumeration .1.3.6.1.4.1.935.10.2.1.2.2.1.25 |
matInvOnOffStatusInverter module On/Off status.rw Enumeration .1.3.6.1.4.1.935.10.2.1.2.2.1.26 |
matSts OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.1.3 |
matStsModuleNumThe number of STS modules.ro INTEGER .1.3.6.1.4.1.935.10.2.1.3.1 |
matStsTableThis table list STS message. SEQUENCE OF MATStsEntry .1.3.6.1.4.1.935.10.2.1.3.2 |
matStsEntryAn entry containing information applicable to a particular STS module. MATStsEntry .1.3.6.1.4.1.935.10.2.1.3.2.1 |
matStsModuleIndexThe index of STS module. PositiveInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.1 |
matStsModuleTypeModule type, 050 represent 50A, 100 represent 100A.ro DisplayString ( SIZE ( 0 .. 3 ) ) .1.3.6.1.4.1.935.10.2.1.3.2.1.2 |
matStsSerialNumModule serial number.ro DisplayString ( SIZE ( 0 .. 15 ) ) .1.3.6.1.4.1.935.10.2.1.3.2.1.3 |
matStsFirmwareVersionFirmware version.ro DisplayString ( SIZE ( 0 .. 7 ) ) .1.3.6.1.4.1.935.10.2.1.3.2.1.4 |
matStsHardwareVersionHardware version.ro DisplayString ( SIZE ( 0 .. 7 ) ) .1.3.6.1.4.1.935.10.2.1.3.2.1.5 |
matStsWarningStateThe values indicate the unrestored traps.
For example,
if 'STS running in fault mode' and 'STS fan fault'
the agent send
the trap 59 and trap 61 to
NMS,
so the value of matConWarningState should be '59,61'.
And then the two events restored, the value of matConWarningState
should change to empty.ro DisplayString ( SIZE ( 0 .. 63 ) ) .1.3.6.1.4.1.935.10.2.1.3.2.1.6 |
matStsMainInputVoltageSTS Mains I/P voltage, the unit is 0.1 Volts.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.7 |
matStsMainInputFreqSTS Mains I/P frequency, the unit is 0.1 Hz.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.8 |
matStsInvInputVoltageSTS INV I/P voltage, the unit is 0.1 volts.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.9 |
matStsInvInputFreqSTS INV I/P frequency, the unit is 0.1 Hz.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.10 |
matStsOutputVoltageSTS O/P voltage, the unit is 0.1 volts.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.11 |
matStsOutputCurrentSTS O/P Current, the unit is 0.1 amp.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.12 |
matStsOutputPowerSTS O/P Power, the unit is VA.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.13 |
matStsOutputFreqSTS O/P frequency, the unit is 0.1 Hz.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.14 |
matStsRuntimeSTS Runtime, the unit is Hour.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.15 |
matStsTemperatureSTS module's Temperature, the unit is 0.1 degree.ro INTEGER .1.3.6.1.4.1.935.10.2.1.3.2.1.16 |
matStsMbsStatusSTS MBS status.ro Enumeration .1.3.6.1.4.1.935.10.2.1.3.2.1.17 |
matStsStatusSTS status.ro Enumeration .1.3.6.1.4.1.935.10.2.1.3.2.1.18 |
matStsRunningModeSTS Running Mode.ro Enumeration .1.3.6.1.4.1.935.10.2.1.3.2.1.19 |
matStsMainHighLossVoltageSTS Main high loss voltage, the unit is 0.1 volts.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.20 |
matStsMainLowLossVoltageSTS Main low loss voltag, the unit is 0.1 volts.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.21 |
matStsInvHighLossVoltageSTS Inverter high loss voltage, the unit is 0.1 volts.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.22 |
matStsInvLosLossVoltageSTS Inverter low loss voltage, the unit is 0.1 volts.ro NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.3.2.1.23 |
matDryContact OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.1.4 |
matDryContactNumThe number of dry contact.ro INTEGER .1.3.6.1.4.1.935.10.2.1.4.1 |
matDryContactTableThis table list dry contact message. SEQUENCE OF MATDryContactEntry .1.3.6.1.4.1.935.10.2.1.4.2 |
matDryContactEntryAn entry containing information of one dry contact. MATDryContactEntry .1.3.6.1.4.1.935.10.2.1.4.2.1 |
matDryContactIndexThe index of dry contact. PositiveInteger .1.3.6.1.4.1.935.10.2.1.4.2.1.1 |
matDryContactStringformat: xx xx xx xx xx xx xx xx xx xx,
xx: alarm code. If the configured alarm is less than 10, then fill the position with '
Alarm code:
Inverter fault 0x01(for 3.5Kva system and 1.5Kva system),
Inverter over load 0x02(for 3.5Kva system and 1.5Kva system),
Inverter fan fault 0x03(for 3.5Kva system and 1.5Kva system),
Inverter power limit 0x04(for 3.5Kva system and 1.5Kva system),
Inverter DC input Abnormal 0x05(for 3.5Kva system and 1.5Kva system),
Inverter low volt off 0x06(for 3.5Kva system and 1.5Kva system),
Inverter lost 0x07(for 3.5Kva system and 1.5Kva system),
Inverter Mains unavailable 0x19(for 3.5Kva system),
Inverter Maintenance Bypass 0x1A(for 3.5Kva system),
Inverter Output 0x1B(for 3.5Kva system),
STS Inv unavailable 0x2A(for 1.5Kva system),
STS Main unavailable 0x2B(for 1.5Kva system),
STS Output overload 0x2C(for 1.5Kva system),
STS OP Short circuit 0x2D(for 1.5Kva system),
STS K1 Relay open 0x23(for 1.5Kva system),
STS SCR1 short 0x24(for 1.5Kva system),
STS SCR2 short 0x25(for 1.5Kva system),
STS INV Bypass Mode 0x2F(for 1.5Kva system),
STS Over temperature 0x30(for 1.5Kva system),
STS MBS Abnormal 0x31(for 1.5Kva system),
STS Fan Lock 0x27(for 1.5Kva system),
STS Fault Mode 0x26(for 1.5Kva system),
STS Eeprom Fault 0x28(for 1.5Kva system),
SPS Power Fail 0x32(for 1.5Kva system),
STS Output abnormal 0x34(for 1.5Kva system),
STS Maintenance Bypass 0x35(for 1.5Kva system),
STS Output 0x36(for 1.5Kva system),
Controller temperature high 0x42(for 3.5Kva system and 1.5Kva system),
Controller eeprom fail 0x43(for 3.5Kva system and 1.5Kva system),
Controller CAN Bus Off 0x45(for 3.5Kva system and 1.5Kva system)rw DisplayString ( SIZE ( 0 .. 29 ) ) .1.3.6.1.4.1.935.10.2.1.4.2.1.2 |
matConfig OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.1.5 |
matConfInvSysOutputFreqInverter system output frequency, can be 500 or 600, the unit is 0.1 Hz.rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.1 |
matConfInvSysOutputVoltInverter system output voltage, can be 1100, 1150,1200,2080,2200,2300,2400.
The unit is 0.1 Volt.rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.2 |
matConfInvSysOutputVoltHighLossOutput voltage high loss of Inverter System, the unit is 0.1 Volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
1100 1170-1270,
1150 1220-1320,
1200 1270-1380,
2080 2200-2400,
2200 2330-2520,
2300 2440-2640,
2400 2540-2760rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.3 |
matConfInvSysOutputVoltLowLossOutput Voltage Low Loss of inverter System, the unit is 0.1 volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
1100 890-1050,
1150 930-1100,
1200 1000-1140,
2080 1760-1980,
2200 1760-2090,
2300 1850-2180,
2400 1930-2280rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.4 |
matConfInvSysInputVoltInverter System Input Voltage, the unit is 0.1 Volt.
This value depends on matConfInvInputVoltage:
matConfInvInputVoltage(0.1V)=480: Range(400-440),
matConfInvInputVoltage(0.1V)=600: Range(500-550)rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.5 |
matConfInvSysPowerLimitInverter System Power Limited level, format: xxx, range: 50 to 100, the unit is percent.rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.6 |
matConfInvSysLineVoltHighLossHigh loss for line voltage of 3.5k inverter module, the unit is 0.1 volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
2080 2180-2650,
2200 2300-2650,
2300 2400-2650,
2400 2500-2650rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.7 |
matConfInvSysLineVoltLowLossLow loss for line voltage of 3.5k inverter module, the unit is 0.1 volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
2080 1850-1980,
2200 1850-2100,
2300 1850-2200,
2400 1850-2300rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.8 |
matConfInvSysPriorityPriority for 3.5K inverter module.rw Enumeration .1.3.6.1.4.1.935.10.2.1.5.9 |
matConfInvSysFanSpeedInverter System fan speed.rw Enumeration .1.3.6.1.4.1.935.10.2.1.5.10 |
matConfStsAcVoltHighLossSTS Module AC Voltage High Loss Volt, the unit is 0.1 volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
1100 1170-1270,
1150 1220-1320,
1200 1270-1380,
2080 2200-2400,
2200 2330-2520,
2300 2440-2640,
2400 2540-2760rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.11 |
matConfStsAcVoltLowLossSTS Module AC Voltage Low Loss Volt, the unit is 0.1 volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
1100 890-1050,
1150 930-1100,
1200 1000-1140,
2080 1760-1980,
2200 1760-2090,
2300 1850-2180,
2400 1930-2280rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.12 |
matConfStsIpvVoltHighLossSTS module Inverter IPV High Loss Volt, the unit is 0.1 volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
1100 1170-1270,
1150 1220-1320,
1200 1270-1380,
2080 2200-2400,
2200 2330-2520,
2300 2440-2640,
2400 2540-2760rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.13 |
matConfStsIpvVoltLowLossSTS module Inverter IPV low Loss Volt, the unit is 0.1 volt.
This value depends on matConfInvSysOutputVolt, the least significant
digit must be zero, see table:
matConfInvSysOutputVolt(0.1V) Range(0.1V)
1100 890-1050,
1150 930-1100,
1200 1000-1140,
2080 1760-1980,
2200 1760-2090,
2300 1850-2180,
2400 1930-2280rw NonNegativeInteger .1.3.6.1.4.1.935.10.2.1.5.14 |
matConfStsPrioritySTS output priority.rw Enumeration .1.3.6.1.4.1.935.10.2.1.5.15 |
matConfStsFanSpeedSTS fan speed.rw Enumeration .1.3.6.1.4.1.935.10.2.1.5.16 |
matTrapTargets OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.1.6 |
matTrapTargetsNumThe number of trap targets.ro INTEGER .1.3.6.1.4.1.935.10.2.1.6.1 |
matTrapTargetsTableThis table list the managers'IP to send traps to. SEQUENCE OF MatTrapTargetsEntry .1.3.6.1.4.1.935.10.2.1.6.2 |
matTrapTargetsEntryAn entry containing information of one trap target. MatTrapTargetsEntry .1.3.6.1.4.1.935.10.2.1.6.2.1 |
matTrapTargetsIndexThe index to a trap receiver entry PositiveInteger .1.3.6.1.4.1.935.10.2.1.6.2.1.1 |
matTrapTargetsAddressThe IP address of the manager to send a trap to.rw DisplayString ( SIZE ( 0 .. 45 ) ) .1.3.6.1.4.1.935.10.2.1.6.2.1.2 |
matTrapTargetsCommunityThe community name to use in the trap when
sent to the manager.rw DisplayString ( SIZE ( 0 .. 31 ) ) .1.3.6.1.4.1.935.10.2.1.6.2.1.3 |
matTrapTypeThe type of trap to be received by the manager.rw Enumeration .1.3.6.1.4.1.935.10.2.1.6.2.1.4 |
matTrapSeverityLevelThe severity level of traps to be received by this manager.rw Enumeration .1.3.6.1.4.1.935.10.2.1.6.2.1.5 |
matTrapTargetsDescDescription of trap receiversrw DisplayString ( SIZE ( 0 .. 31 ) ) .1.3.6.1.4.1.935.10.2.1.6.2.1.6 |
matTraps OBJECT IDENTIFIER .1.3.6.1.4.1.935.10.2.2 |
matInvFaultMAJOR: Inverter fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.1 |
matReturnFromInvFaultOBSERVE: Return from Inverter fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.2 |
matInvOverLoadMAJOR: Inverter Over-loading. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.3 |
matReturnFromInvOverLoadOBSERVE: Return from Inverter Over-loading. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.4 |
matInvFanFaultMAJOR: Inverter Fan fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.5 |
matReturnFromInvFanFaultOBSERVE: Return from Inverter Fan fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.6 |
matInvTempPowerLimitMAJOR: Inverter power limit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.7 |
matReturnFromInvTempPowerLimitOBSERVE: Return from Inverter power limit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.8 |
matInvInputAbnormalMAJOR: Inverter input abnormal. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.9 |
matReturnFromInvInputAbnormalOBSERVEReturn from Inverter input abnormal. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.10 |
matInvLowInputShutdownMAJOR: Inverter shut down due to low input voltage. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.11 |
matReturnFromInvLowInputShutdownOBSERVE: Return from Inverter shut down due to low input voltage. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.12 |
matInvNotRespondCRITICAL: Inverter disconnected. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.13 |
matReturnFromInvNotRespondOBSERVE: Inverter connected. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.14 |
matInvBusVoltageOverLimitCRITICAL: Inverter Bus voltage over the maximal level. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.15 |
matReturnFromInvBusVoltOverLimitOBSERVE: Return from Inverter Bus voltage over the maximal level. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.16 |
matInvBusVoltageUnderLimitCRITICAL: Inverter Bus volt under the minimal level. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.17 |
matReturnFromInvBusVoltUnderLimitOBSERVE: Return from Inverter Bus volt under the minimal level. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.18 |
matInvBusSoftFailCRITICAL: Inverter Bus Soft Start Fail. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.19 |
matReturnFromInvBusSoftFailOBSERVE: Return from Inverter Bus Soft Start Fail. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.20 |
matInvOutputShortCRITICAL: Inverter Output Short. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.21 |
matReturnFromInvOutputShortOBSERVE: Return from Inverter Output Short. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.22 |
matInvOutputVoltLowCRITICAL: Inverter output voltage low. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.23 |
matReturnFromInvOutputVoltLowOBSERVE: Return from Inverter output voltage low. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.24 |
matInvOutputVoltHighCRITICAL: Inverter output voltage high. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.25 |
matReturnFromInvOutputVoltHighOBSERVE: Return from Inverter output voltage high. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.26 |
matInvTemperatureHighCRITICAL: Inverter Temperature High. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.27 |
matReturnFromInvTemperatureHighOBSERVE: Return from Inverter Temperature High. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.28 |
matInvNegativePowerProtectCRITICAL: Inverter negative power protection. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.29 |
matReturnFromInvNegativePowerProtectOBSERVE: Return from Inverter negative power protection. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.30 |
matInvPulseFaultCRITICAL: Inverter Sync Pulse Fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.31 |
matReturnFromInvPulseFaultOBSERVE: Return from Inverter Sync Pulse Fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.32 |
matInvEPOShutdownCRITICAL: Inverter EPO shutdown. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.33 |
matReturnFromInvEPOShutdownOBSERVE: Return from Inverter EPO shutdown. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.34 |
matInvSoftStartFailCRITICAL: Inverter soft start fail. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.35 |
matReturnFromInvSoftStartFailOBSERVE: Return from Inverter soft start fail. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.36 |
matInvEEPROMFaultMAJOR: Inverter EEPROM fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.37 |
matReturnFromInvEEPROMFaultOBSERVE: Return from Inverter EEPROM fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.38 |
matInvBypassSCRShortCRITICAL: Inverter Bypass SCR Short. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.39 |
matReturnFromInvBypassSCRShortOBSERVE: Return from Inverter Bypass SCR Short. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.40 |
matInvMBSPosErrorCRITICAL: Inverter MBS Position Error. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.41 |
matReturnFromInvMBSPosErrorOBSERVE: Return from Inverter MBS Position Error. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.42 |
matInvBackfeedRelayOpenCRITICAL: Inverter Backfeed Relay Open. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.43 |
matReturnFromInvBackfeedRelayOpenOBSERVE: Return from Inverter Backfeed Relay Open. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.44 |
matInvHardwareErrorCRITICAL: Inverter Hardware Detection Error. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.45 |
matReturnFromInvHardwareErrorOBSERVE: Return from Inverter Hardware Detection Error. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.46 |
matInvMainUnavailableMAJOR: Inverter Mains Unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.47 |
matReturnFromInvMainUnavailableOBSERVE: Return from Inverter Mains Unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.48 |
matInvMaintenaceBypassMAJOR: Inverter Maintenance Bypass. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.49 |
matReturnFromInvMaintenaceBypassOBSERVE: Return from Inverter Maintenance Bypass. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.50 |
matStsBypassUnavailableMAJOR: STS Bypass unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.51 |
matReturnFromStsBypassUnavailableOBSERVE: Return from STS Bypass unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.52 |
matStsBackfeedRelayOpenMAJOR: STS Back-feed relay open. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.53 |
matReturnFromStsBackfeedRelayOpenOBSERVE: Return from STS Back-feed relay open. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.54 |
matStsScr1ShortCurcuitCRITICAL: STS SCR1 short circuit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.55 |
matReturnFromStsScr1ShortCurcuitOBSERVE: Return from STS SCR1 short circuit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.56 |
matStsScr2ShortCurcuitCRITICAL: STS SCR2 short circuit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.57 |
matReturnFromStsScr2ShortCurcuitOBSERVE: Return from STS SCR2 short circuit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.58 |
matStsFaultModeCRITICAL: STS running in fault mode. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.59 |
matReturnFromStsFaultModeOBSERVE: Return from STS running in fault mode. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.60 |
matStsFanFaultMAJOR: STS fan fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.61 |
matReturnFromStsFanFaultOBSERVE: Return from STS fan fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.62 |
matStsEEPROMFaultMAJOR: STS EEPROM fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.63 |
matReturnFromStsEEPROMFaultOBSERVE: Return from STS EEPROM fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.64 |
matStsInvFailMAJOR: STS Inverter unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.65 |
matReturnFromStsInvFailOBSERVE: Return from STS Inverter unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.66 |
matStsMainsFailMAJOR: STS Mains unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.67 |
matReturnFromStsMainFailOBSERVE: Return from STS Mains unavailable. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.68 |
matStsOverLoadMAJOR: STS Output over load. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.69 |
matReturnFromStsOverLoadOBSERVE: Return from STS Output over load. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.70 |
matStsOutputShortCircuitCRITICAL: STS Output short circuit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.71 |
matReturnFromStsOutputShortCircuitOBSERVE: Return from STS Output short circuit. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.72 |
matStsInvBypassModeCRITICAL: STS Inverter bypass mode. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.73 |
matReturnFromStsInvBypassModeOBSERVE: Return from STS Inverter bypass mode. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.74 |
matStsTemperatureHighMAJOR: STS temperature high. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.75 |
matReturnFromStsTemperatureHighOBSERVE: Return from STS temperature high. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.76 |
matStsMBSPosFaultCRITICAL: STS MBS in abnormal position. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.77 |
matReturnFromStsMBSPosFaultOBSERVE: Return from STS MBS in abnormal position. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.78 |
matStsControlPowerFailCRITICAL: STS Control power fail. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.79 |
matReturnFromStsControlPowerFailOBSERVE: Return from STS Control power fail. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.80 |
matStsNotRespondCRITICAL: STS disconnected. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.81 |
matReturnFromStsNotRespondOBSERVE: STS connected. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.82 |
matStsOutputAbnormalMAJOR: STS Output abnormal. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.83 |
matReturnFromStsOutputAbnormalOBSERVE: Return from STS Output abnormal. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.84 |
matStsMaintenanceBypassMAJOR: STS Maintenance Bypass. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.85 |
matReturnFromStsMaintenanceBypassOBSERVE: Return from STS Maintenance Bypass. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.86 |
matConBatteryLowCRITICAL: Controller Battery Low. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.87 |
matReturnFromConBatteryLowOBSERVE: Return from Controller Battery Low. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.88 |
matConTemperatureHighCRITICAL: Controller temperature High. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.89 |
matReturnFromConTemperatureHighOBSERVE: Return from Controller temperature High. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.90 |
matConEEPROMFaultMAJOR: Controller EEPROM fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.91 |
matReturnFromConEEPROMFaultOBSERVE: Return from Controller EEPROM fault. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.92 |
matConBatteryVoltHighCRITICAL: Controller Battery voltage high. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.93 |
matReturnFromConBatteryVoltHighOBSERVE: Return from Controller Battery voltage high. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.94 |
matConCanBusOffCRITICAL: Controller CAN bus off. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.95 |
matReturnFromConCanBusOffOBSERVE: Return from Controller CAN bus off. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.96 |
matConCommunicationLostCRITICAL: Controller communication lost. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.97 |
matReturnFromCommunicationLostOBSERVE: Return from Controller communication lost. TRAP-TYPE .1.3.6.1.4.1.935.10.2.2.0.98 |