SWITCH
AI MIB Summary
The SWITCH MIB module provides SNMP access to the system-level attributes of network switches, including device identification, operational status, and hardware health metrics. It enables centralized monitoring of switch inventory, uptime, and configuration parameters across the network infrastructure.
The System Information of the switch
Main OID:
switch.1.3.6.1.4.1.52642.1
1147
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
1147 total| Object Name |
|---|
switchThe System Information of the switch MODULE-IDENTITY .1.3.6.1.4.1.52642.1 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1 |
memory OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.1 |
memIndexBogus Index. This should always return the integer 0.ro Integer32 .1.3.6.1.4.1.52642.1.1.1.1 |
memTotalRealThe total amount of real/physical memory installed on this host.ro Integer32 UNITS "kB" .1.3.6.1.4.1.52642.1.1.1.5 |
memTotalFreeThe total amount of memory free or available for use on
this host.This value typically covers both real memory
and swap space or virtual memory.ro Integer32 UNITS "kB" .1.3.6.1.4.1.52642.1.1.1.11 |
memTotalUsedThe total amount of memory used on this host.
This value typically covers both real memory
and swap space or virtual memory.ro Integer32 UNITS "kB" .1.3.6.1.4.1.52642.1.1.1.12 |
systemStats OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.2 |
ssIndexBogus Index.This should always return the integer 1.ro Integer32 .1.3.6.1.4.1.52642.1.1.2.1 |
ssCpuIdleThe percentage of processor time spent idle, calculated over the last
minute.ro Integer32 .1.3.6.1.4.1.52642.1.1.2.11 |
sysProcessTableThe system precess table. SEQUENCE OF SysProcessEntry .1.3.6.1.4.1.52642.1.1.2.100 |
sysProcessEntryAn entity process entry. Each entry consists of information of an process.
The sysProcessIndex exclusively defines an process id. SysProcessEntry .1.3.6.1.4.1.52642.1.1.2.100.1 |
sysProcessIndexThe pid of process. Integer32 .1.3.6.1.4.1.52642.1.1.2.100.1.1 |
sysProcessNameThe name of the process.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.2.100.1.2 |
operate OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.3 |
configSaveThis should always write running-config to startup-config.And the
valid set value is 1. When get the configSave value, 1 means success, 0 means failure.rw Integer32 .1.3.6.1.4.1.52642.1.1.3.1 |
reloadThis should allow to reboot the switch.The valid input value is 1 and 2.
Value 1 means the switch will reboot without savingcurrent configuration.
Value 2 means the switch will savecurrent configuration before reboot the switch.rw Enumeration .1.3.6.1.4.1.52642.1.1.3.2 |
rebootAtSpecify auto reboot parameters at the special time. 0 is mean clear.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.3.3 |
rebootDelaySpecify auto reboot parameters reboot after delay some time. The value is [1, 720] minutes. 0 is mean clear.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.3.4 |
versionDescription the current versionro OCTET STRING .1.3.6.1.4.1.52642.1.1.3.5 |
serviceTelnetTelnet service.1:enable 2:disable.rw Enumeration .1.3.6.1.4.1.52642.1.1.3.6 |
loginFailThis node only for login fail for three time. Integer32 .1.3.6.1.4.1.52642.1.1.3.7 |
lastCommandSave the last command line and time.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.3.8 |
currentRunningImageShow the current running image.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.3.9 |
sysStartUpTimeShow system startup time.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52642.1.1.3.10 |
sysImageTableThe system image management table. SEQUENCE OF SysImageEntry .1.3.6.1.4.1.52642.1.1.4 |
sysImageEntryAn entity image entry.Each entry consists of information of an entity image.
The sysImageIndex exclusively defines an image file. SysImageEntry .1.3.6.1.4.1.52642.1.1.4.1 |
sysImageIndexThe index of image. Integer32 .1.3.6.1.4.1.52642.1.1.4.1.1 |
sysImageNameThe file name of the image.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.4.1.2 |
sysImageCreateTimeThe create time of the image.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.4.1.3 |
sysImageVersionThe version of the image.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.4.1.4 |
sysImageSizeThe size of the image.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.4.1.5 |
sysImageDirThe dir of the image.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.4.1.6 |
sysImageIsBootThis image is the boot image (1),and is not the boot image (2). Only support enable(1).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.4.1.7 |
flash OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.5 |
flashManMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.5.1 |
flashDevice OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.5.1.1 |
flashTableThis table gives the properties of all the flashes on the system. SEQUENCE OF FlashEntry .1.3.6.1.4.1.52642.1.1.5.1.1.1 |
flashEntryThe entry of flashTable. FlashEntry .1.3.6.1.4.1.52642.1.1.5.1.1.1.1 |
flhIndexThe index of flashTable.It has a minimum value of 1, and maximum value
of the same as the value of flhSupportNum. Integer32 .1.3.6.1.4.1.52642.1.1.5.1.1.1.1.1 |
flhSizeSpecifies the total size of the flash device indexed by flhIndex.
The value should be zero if the flash is removed for a removable device.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.1.1.1.2 |
flhFreeSpecifies the free size of the flash device.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.1.1.1.3 |
flhNameThe flash name within the system.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.1.1.1.4 |
flhDescrDESCRIPTION of the purpose of the flash in the system.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.1.1.1.6 |
flhFiles OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.5.1.1.2 |
flhFileTableTable of file information. SEQUENCE OF FlhFileEntry .1.3.6.1.4.1.52642.1.1.5.1.1.2.1 |
flhFileEntryAn entry representing a file.Indexed using flash number, partition
number, and file number. FlhFileEntry .1.3.6.1.4.1.52642.1.1.5.1.1.2.1.1 |
flhFileIndexIndex of the table, whose range is from 1 to 2147483647. Integer32 .1.3.6.1.4.1.52642.1.1.5.1.1.2.1.1.1 |
flhFileNameA valid file name supported by the file system.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.1.2.1.1.2 |
flhFileSizeThe file size in bytes excluding the file header of file system.
The value should be greater than zero.ro Integer32 .1.3.6.1.4.1.52642.1.1.5.1.1.2.1.1.3 |
flhFileTimeThe time when this file is modified last time.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.1.2.1.1.4 |
flashOperate OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.5.1.2 |
flhOpTableTable used to operate flash. SEQUENCE OF FlhOpEntry .1.3.6.1.4.1.52642.1.1.5.1.2.1 |
flhOpEntryNote an operation can not be stopped until it is finished.
If notification is configured, NMS will receive a notification
at the end of the operation.
Entries in the table will be removed automatically in 5 minutes.
It can also be deleted by NMS directly. FlhOpEntry .1.3.6.1.4.1.52642.1.1.5.1.2.1.1 |
flhOperIndexSpecifies the index of an entry.It is a
random value when creating an entry. Integer32 .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.1 |
flhOperTypeSpecifies the operation to be executed.
flash2Flash(1) Copy a file from flash to flash.
net2Flash(2) Copy a file from net to flash;
flash2Net(3) Copy a file from flash to net.
delete(4) Delete a file from flash, the file name is specified by flhOperSourceFile;
rename(5) Change a file's name.rw Enumeration .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.2 |
flhOperProtocolSpecifies the protocol used to transfer file.
The default protocol is ftp.
Both member switch and commander switch can use them if they
support HGMP v2.
1 FTP
2 TFTPrw Enumeration .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.3 |
flhOperServerAddressThe address of remote host acting as server for operation.
The default value is 0.0.0.0.rw IpAddress .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.4 |
flhOperServerUserWhen using ftp to transfer files, the user name must be
specified through this node.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.5 |
flhOperPasswordRemote user password for copying via ftp protocol.Optionally,
This object may be ignored for protocols other than ftp.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.6 |
flhOperSourceFileSpecifies the source file name to be transferred.
It may be located on flash or remote server.
It may include the file path if it is applicable.
It must be specified.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.7 |
flhOperDestinationFileSpecifies the destination file name.
It may be located on flash or remote server.
It may include the file path if it is applicable.
If it is not specified, the destination file name
is the same as source file name for application.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.8 |
flhOperStatusThe status of the specified operation can be one of
the following.
opInProgress(1) : the operation is in process.
opSuccess(2) : the operation has been completed successfully.
opInvalid(3) : the command is invalid or command-protocol-device combination is unsupported by the system.
opInvalidProtocol(4) :invalid protocol is specified
opInvalidSourceName(5) :invalid source file name is specified.
opInvalidDestName(6) :invalid target name is specified.
opInvalidServerAddress(7) :invalid server address is specified
opDeviceBusy(8) :the device is in use and locked by another process
opDeviceOpenError(9) :invalid device name is specified.
opDeviceError(10) : device read, write or erase error
opDeviceNotProgrammable(11) :device isread-only but a write or erase operation was specified.
opDeviceFull(12) : device is filled to capacity
opFileOpenError(13) :invalid file name; file not found in partition
opFileTransferError(14) :file transfer was unsuccessful
opFileChecksumError(15) :file checksum in Flash is invalid
opNoMemory(16) :system is running in low on memory
opUnknownFailure(19) :failure which is unknown
opDeleteFileOpenError(20) :file is in used by another process
opDeleteInvalidDevice(21) :invalid device name is specified
opDeleteInvalidFunction(22) :deleted operation is unsupported by the device.
opDeleteOperationError(23) :operation is in a low error
opDeleteInvalidFileName(24) :invalid file name is specified
pDeleteDeviceBusy(25) :the device is in use and locked by another process.
opDeleteParaError(26) :the parameters are invalid
opDeleteInvalidPath(27) :the file path is invalid.ro FlashOperationStatus .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.9 |
flhOperIsManagementIfIf use management interface running SNMP or not, true(1):enable.false(2):disablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.12 |
flhOperRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.5.1.2.1.1.13 |
cf OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.6 |
cfManMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.6.1 |
cfDevice OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.6.1.1 |
cfTableThis table gives the properties of all the cfes on the system. SEQUENCE OF CfEntry .1.3.6.1.4.1.52642.1.1.6.1.1.1 |
cfEntryThe entry of cfTable. CfEntry .1.3.6.1.4.1.52642.1.1.6.1.1.1.1 |
cfIndexThe index of cfTable.It has a minimum value of 1, and
maximum value of the same as the value of cfSupportNum.ro Integer32 .1.3.6.1.4.1.52642.1.1.6.1.1.1.1.1 |
cfSizeSpecifies the total size of the cf device indexed
by cfIndex.The value should be zero if the cf is
removed for a removable device.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.1.1.1.2 |
cfFreeSpecifies the free size of the cf device.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.1.1.1.3 |
cfNameThe cf name within the system.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.1.1.1.4 |
cfDescrDescription of the purpose of the cf in the system.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.1.1.1.6 |
cfFiles OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.6.1.1.2 |
cfFileTableTable of file information. SEQUENCE OF CfFileEntry .1.3.6.1.4.1.52642.1.1.6.1.1.2.1 |
cfFileEntryAn entry representing a file. Indexed using cf number,
partition number, and file number. CfFileEntry .1.3.6.1.4.1.52642.1.1.6.1.1.2.1.1 |
cfFileIndexIndex of the table, whose range is from 1 to 2147483647 Integer32 .1.3.6.1.4.1.52642.1.1.6.1.1.2.1.1.1 |
cfFileNameA valid file name supported by the file system.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.1.2.1.1.2 |
cfFileSizeThe file size in bytes excluding the file
header of file system. The value should be greater than zero.ro Integer32 .1.3.6.1.4.1.52642.1.1.6.1.1.2.1.1.3 |
cfFileTimeThe time when this file is modified last time.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.1.2.1.1.4 |
cfOperate OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.6.1.2 |
cfOpTableTable used to operate cf. SEQUENCE OF CfOpEntry .1.3.6.1.4.1.52642.1.1.6.1.2.1 |
cfOpEntryNote an operation can not be stopped until it is finished.
If notification is configured, NMS will receive a notification
at the end of the operation.
Entries in the table will be removed automatically in 5 minutes.
It can also be deleted by NMS directly. CfOpEntry .1.3.6.1.4.1.52642.1.1.6.1.2.1.1 |
cfOperIndexSpecifies the index of an entry. It is a
random value when creating an entry. Integer32 .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.1 |
cfOperTypeSpecifies the operation to be executed.
net2CfWithErase Copy a file to cf; erase cf beforehand.
net2CfWithoutErase Copy a file to cf; do not erase cf
beforehand.
cf2Net Copy a file from cf.
delete Delete a file from cf, the file name is
specified by cfOperSourceFile;
rename Change a file's name.rw Enumeration .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.2 |
cfOperProtocolSpecifies the protocol used to transfer file.The default protocol is ftp.
when 'clusterftp' or 'clustertftp' is selected, the cfOperServerAddress needn't
be set the server address can be acquired automatically, the value of
cfOperServerAddress is uncertain during operation.Both member switch and
commander switch can use them if they support HGMP v2.rw Enumeration .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.3 |
cfOperServerAddressThe address of remote host acting as server for operation.
The default value is 255.255.255.255.rw IpAddress .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.4 |
cfOperServerUserWhen using ftp to transfer files, the user name must be specified through
this node.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.5 |
cfOperPasswordRemote user password for copying via ftp protocol.Optionally.
This object may be ignored for protocols other than ftp.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.6 |
cfOperSourceFileSpecifies the source file name to be transferred.
It may be located on cf or remote server.
It may include the file path if it is applicable.
It must be specified.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.7 |
cfOperDestinationFileSpecifies the destination file name.
It may be located on cf or remote server.
It may include the file path if it is applicable.
If it is not specified, the destination file name
is the same as source file name for application.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.8 |
cfOperStatusThe status of operation.ro CfOperationStatus .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.9 |
cfOperIsManagementIfIf use management interface running SNMP or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.12 |
cfOperRowStatusThe status of this conceptual row.Now only realize CreateAndGo
and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.6.1.2.1.1.13 |
sysTrap OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.7 |
time OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.8 |
timeSet OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.8.1 |
timeSetClockcurrent time. format HH:MM:SS.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.1.1 |
timeSetMonthMonth of the year. range is [1, 12].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.1.2 |
timeSetDayDay of the month. range is [1, 31].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.1.3 |
timeSetYearYear of the date. range is [2000, 2037].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.1.4 |
timezoneSetTableThe table of SummerTime. SEQUENCE OF TimezoneSetEntry .1.3.6.1.4.1.52642.1.1.8.2 |
timezoneSetEntryThe entry of timezone. TimezoneSetEntry .1.3.6.1.4.1.52642.1.1.8.2.1 |
timezoneSetZoneNameZone name, must be less than 32 characters. only include [a-zA-Z_]. The begin and end character must be alphabet. Its length range is [3, 32)rw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.2.1.1 |
timezoneSetTypePositive/Negative time zone offset from UTC.
0 means Negative
1 means Positiverw Integer32 .1.3.6.1.4.1.52642.1.1.8.2.1.2 |
timezoneSetHoursHours offset from UTC, must be range 0~23.rw Integer32 .1.3.6.1.4.1.52642.1.1.8.2.1.3 |
timezoneSetMinutesMinutes offset from UTC, must be range 0~59.rw Integer32 .1.3.6.1.4.1.52642.1.1.8.2.1.4 |
timezoneSetSecondsSeconds offset from UTC, must be range 0~59.rw Integer32 .1.3.6.1.4.1.52642.1.1.8.2.1.5 |
timezoneSetStateThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.8.2.1.6 |
recurrentSummerTimeTableThe table of SummerTime. SEQUENCE OF RecurrentSummerTimeEntry .1.3.6.1.4.1.52642.1.1.8.3 |
recurrentSummerTimeEntryThe entry of SummerTime. RecurrentSummerTimeEntry .1.3.6.1.4.1.52642.1.1.8.3.1 |
recurrentSummerTimeZoneNameZone name, must be less than 32 characters. only include [a-zA-Z_]. The begin and end character must be alphabet. Its length range is [1, 32)rw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.3.1.1 |
recurrentSummerTimeStartMonthStart month of the year. range is [1,12]rw Integer32 .1.3.6.1.4.1.52642.1.1.8.3.1.2 |
recurrentSummerTimeStartDayDay in month to start. range is [1, 31].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.3.1.3 |
recurrentSummerTimeStartClockTime to start. format HH:MM:SSrw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.3.1.4 |
recurrentSummerTimeEndMonthMonth to end. range is [1, 12].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.3.1.5 |
recurrentSummerTimeEndDayDay in month to end. range is [1, 31].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.3.1.6 |
recurrentSummerTimeEndClockTime to end. format HH:MM:SSrw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.3.1.7 |
recurrentSummerTimeOffsetSummer time offset, unit is minute. range is [1, 1440].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.3.1.8 |
recurrentSummerTimeStateThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.8.3.1.9 |
summerTimeTableThe table of SummerTime. SEQUENCE OF SummerTimeEntry .1.3.6.1.4.1.52642.1.1.8.4 |
summerTimeEntryThe entry of SummerTime. SummerTimeEntry .1.3.6.1.4.1.52642.1.1.8.4.1 |
summerTimeZoneNameZone name, must be less than 32 characters.
only include [a-zA-Z_]. The begin and end character must be alphabet. Its length range is [1, 32)rw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.4.1.1 |
summerTimeStartMonthStart month of the year. range is [1, 12].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.4.1.2 |
summerTimeStartDayStart day of month. range is [1, 31].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.4.1.3 |
summerTimeStartYearStart year of summer-time. range is [2000, 2037].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.4.1.4 |
summerTimeStartClockStart time. format HH:MM:SS.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.4.1.5 |
summerTimeEndMonthEnd month of year. range is [1, 12].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.4.1.6 |
summerTimeEndDayEnd day of month. range is [1, 31].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.4.1.7 |
summerTimeEndYearEnd year of summer time. range is [2000, 2037].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.4.1.8 |
summerTimeEndClockEnd time. format HH:MM:SS.rw OCTET STRING .1.3.6.1.4.1.52642.1.1.8.4.1.9 |
summerTimeOffsetSummer time offset, unit is minute. range is [1, 1440].rw Integer32 .1.3.6.1.4.1.52642.1.1.8.4.1.10 |
summerTimeStateThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.1.8.4.1.11 |
cpuUsage OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.1.9 |
fiveSecondsCPU usage within five seconds.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.9.1 |
oneMinuteCPU usage within one minute.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.9.2 |
fiveMinutesCPU usage within five minutes.ro OCTET STRING .1.3.6.1.4.1.52642.1.1.9.3 |
syslog OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.2 |
syslogTimestampThe log timestamp type.
0 RBSD(RFC3164 or bsd).
1 RISO(RFC3339 or iso).
2 RFULL(date).
3 NONE.rw TimeStampFormatType .1.3.6.1.4.1.52642.1.2.1 |
syslogOperateLogEnableThe state of log operate true(1):enable.false(2):disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.2.2 |
syslogBuffer OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.2.3 |
syslogBufferMaxSizeThe maximum number of messages that can be storedin logbuffer.MaxSize range 10~1000.rw INTEGER .1.3.6.1.4.1.52642.1.2.3.1 |
syslogbufferSeverityThe operations staff can selectively filter the messages
with priority which consists of severity that generates
the message and severity of the message.Range 0~7.rw MessageLevelType .1.3.6.1.4.1.52642.1.2.3.2 |
syslogBuffercurrentMessagesThe number of log messages stored in logbuffer.ro Unsigned32 .1.3.6.1.4.1.52642.1.2.3.3 |
syslogBufferDroppedMessagesThe number of log messages dropped in logbuffer.ro Counter32 .1.3.6.1.4.1.52642.1.2.3.4 |
syslogFile OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.2.4 |
syslogFileEnableThe state of log merge true(1):enable.false(2):disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.2.4.1 |
syslogFileSeverityThe operations staff can selectively filter the messages with priority
which consists of severity that generates the message and severity of
the message.Range 0~7.rw MessageLevelType .1.3.6.1.4.1.52642.1.2.4.2 |
syslogServer OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.2.5 |
syslogServerEnableThe state of syslogtrap: true(1): enable.false(2): disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.2.5.1 |
syslogServerFacilityThe operations staff can selectively filter the messages with priority
which consists of facility that generates the message and severity of
the message.Value range 0~11 or 16~23.rw FacilityType .1.3.6.1.4.1.52642.1.2.5.2 |
syslogServerSeverityThe operations staff can selectively filter the messages with priority
which consists of severity that generates the message and severity of
the message.Value range 0~7.default 4rw MessageLevelType .1.3.6.1.4.1.52642.1.2.5.3 |
syslogServerTableThe table of loghost. SEQUENCE OF SyslogServerEntry .1.3.6.1.4.1.52642.1.2.5.4 |
syslogServerEntryThe loghost entry of syslog. SyslogServerEntry .1.3.6.1.4.1.52642.1.2.5.4.1 |
syslogServerIpaddressThe ip address of loghost.ro IpAddress .1.3.6.1.4.1.52642.1.2.5.4.1.1 |
syslogServerMgmtIfThe mgmt if of loghost.
1 noUse.
2 useMgmtIf.ro Enumeration .1.3.6.1.4.1.52642.1.2.5.4.1.2 |
syslogServerRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.2.5.4.1.3 |
syslogTrap OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.2.6 |
syslogTrapEnableThe state of syslog trap. true(1):enable.false(2):disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.2.6.1 |
syslogTrapSeverityThe operations staff can selectively filter the messages with priority
which consists of severity that generates the message and severity of
the message.
0 high.
1 middle.
2 lower.
3 minor.rw MessageTrapLevelType .1.3.6.1.4.1.52642.1.2.6.2 |
syslogMerge OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.2.7 |
syslogMergeEnableThe state of log merge true(1):enable.false(2):disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.2.7.1 |
syslogMergeFifoSizeThe logging merge fifo-size, specify the logging merge buffer.rw INTEGER .1.3.6.1.4.1.52642.1.2.7.2 |
syslogMergeTimeoutThe logging merge timeout value, specify the logging merge interval.default 10.rw INTEGER .1.3.6.1.4.1.52642.1.2.7.3 |
syslogSyncSpecify sync parameter. true(1): sync the syslog and return value is always 0.rw INTEGER .1.3.6.1.4.1.52642.1.2.8 |
syslogClearLogBuffClear logging buffer. true(1): clear the logging buffer and return value is always 0.rw INTEGER .1.3.6.1.4.1.52642.1.2.9 |
mirror OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.3 |
mSSrcIfTableA list of mirror session source port entries. SEQUENCE OF MSSrcIfEntry .1.3.6.1.4.1.52642.1.3.1 |
mSSrcIfEntryA list of parameters that describe a source port to be added to a mirror
session. MSSrcIfEntry .1.3.6.1.4.1.52642.1.3.1.1 |
mSSrcIfIDAn index that uniquely identifies an entry in the mirror session table. Integer32 .1.3.6.1.4.1.52642.1.3.1.1.1 |
mSSrcIfIndexIfIndex of mirror group source port. including ethernet port and agg port Integer32 .1.3.6.1.4.1.52642.1.3.1.1.2 |
mSSrcIfDirectionMirror direction of source port.if the direction first configured
as rx, then configure tx, then the direction will be both.rw Enumeration .1.3.6.1.4.1.52642.1.3.1.1.3 |
mSSrcIfRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.3.1.1.4 |
mSSrcVlanTableA list of mirror session source vlan entries. SEQUENCE OF MSSrcVlanEntry .1.3.6.1.4.1.52642.1.3.2 |
mSSrcVlanEntryA list of parameters that describe a source vlan to be added to a mirror session. MSSrcVlanEntry .1.3.6.1.4.1.52642.1.3.2.1 |
mSSrcVlanIDAn index that uniquely identifies an entry in the mirror session table. Integer32 .1.3.6.1.4.1.52642.1.3.2.1.1 |
mSSrcVlanNumIfIndex of mirror group source vlan. Integer32 .1.3.6.1.4.1.52642.1.3.2.1.2 |
mSSrcVlanDirectionMirror direction of source vlan.if the direction first configured as
rx, then configure tx, then the direction will be both.rw Enumeration .1.3.6.1.4.1.52642.1.3.2.1.3 |
mSSrcVlanRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.3.2.1.4 |
mSDestIfTableA list of mirror group dest port entries. SEQUENCE OF MSDestIfEntry .1.3.6.1.4.1.52642.1.3.3 |
mSDestIfEntryA list of parameters that describe a dest port to be added to a mirror group. MSDestIfEntry .1.3.6.1.4.1.52642.1.3.3.1 |
mSDestIfIDAn index that uniquely identifies an entry in the mirror session table. Integer32 .1.3.6.1.4.1.52642.1.3.3.1.1 |
mSDestIfIndexIfIndex of mirror group dest port. only ethernet port.rw Integer32 .1.3.6.1.4.1.52642.1.3.3.1.2 |
mSSessionTypesession type.rw Enumeration .1.3.6.1.4.1.52642.1.3.3.1.3 |
mSDestVlanIDIfIndex of mirror group dest vlan.rw Integer32 .1.3.6.1.4.1.52642.1.3.3.1.4 |
mSDestIfRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.3.3.1.5 |
mSTableA list of mirror group entries. SEQUENCE OF MSEntry .1.3.6.1.4.1.52642.1.3.4 |
mSEntryA list of parameters that describe a mirror group. MSEntry .1.3.6.1.4.1.52642.1.3.4.1 |
mSIDAn index that uniquely identifies an entry in the mirror session table. Integer32 .1.3.6.1.4.1.52642.1.3.4.1.1 |
mSTypeThe type of a mirror session.
1 Local.
2 remote.ro Enumeration .1.3.6.1.4.1.52642.1.3.4.1.2 |
mSStatusThe status of a mirror session.A mirror session will be active only when it has destination port.
1 Active.
2 Inactive.ro Enumeration .1.3.6.1.4.1.52642.1.3.4.1.3 |
mSRowStatusThe status of this conceptual row.Now only realize Destroy and Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.3.4.1.4 |
mSEscapeMacTableA list of mirror session escape mac entries. SEQUENCE OF MSEscapeMacEntry .1.3.6.1.4.1.52642.1.3.5 |
mSEscapeMacEntryA list of parameters that describe a escape mac to be added to a mirror session. MSEscapeMacEntry .1.3.6.1.4.1.52642.1.3.5.1 |
mSEscapeMacIndexThe index of a escape mac.Range 1~2. INTEGER .1.3.6.1.4.1.52642.1.3.5.1.1 |
mSEscapeMacAddressSpecify certain mac address as special and not mirror.rw OCTET STRING .1.3.6.1.4.1.52642.1.3.5.1.2 |
mSEscapeMacMaskMac mask of mirror Specify certain mac address.rw OCTET STRING .1.3.6.1.4.1.52642.1.3.5.1.3 |
mSEscapeMacRowStatusThe status of this conceptual row.Now only realize CreateAndGo(4) and Destroy(6) and Active(1).
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.3.5.1.4 |
portSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.4 |
portSecurityObject OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.4.1 |
portSecurityPortTableThis table defines the securityStatus of each secure port.
Each port can have a number of authorised MAC addresses, and these are
stored in the portSecurityStaticAddressTable and
portSecurityDynamicAddressTable. SEQUENCE OF PortSecurityPortEntry .1.3.6.1.4.1.52642.1.4.1.1 |
portSecurityPortEntryThere is a Rowin this table for each secure port and It is indexed
using the object ifIndex in RFC1213-MIB. PortSecurityPortEntry .1.3.6.1.4.1.52642.1.4.1.1.1 |
portSecurityEnableThis attribute controls the system wide operation of mac-authentication.
The system-wide mac-authentication options become non-operational
when this attribute is set to disabled.rw Enumeration .1.3.6.1.4.1.52642.1.4.1.1.1.1 |
portSecurityViolationModeThis attribute determines what action to be taken when a security violation is detected
protect(0): discard packet silently
restrict(1): discard packet and print log
shutdown(2): discard packet, log and set the interface error-disabled.rw Enumeration .1.3.6.1.4.1.52642.1.4.1.1.1.2 |
portSecurityMaximumNumberOfMacAddressesThis indicates the maximum value that mac addresses can be learned.
Those objects are bound by the relationship:
staticNumberOfConfiguredMacAddresses
<= totalNumberOfMacAddresses
<= portSecurityMaximumMacAddresses.rw Integer32 .1.3.6.1.4.1.52642.1.4.1.1.1.3 |
portSecurityCurrentNumberOfMacAddressesThis indicates thecurrent number of Mac Addresses.ro Integer32 .1.3.6.1.4.1.52642.1.4.1.1.1.4 |
portSecurityStaticAddressTableThis table stores the static MAC addresses assigned to each port. SEQUENCE OF PortSecurityStaticAddressEntry .1.3.6.1.4.1.52642.1.4.1.2 |
portSecurityStaticAddressEntryThis table stores the static MAC addresses assigned to each port. PortSecurityStaticAddressEntry .1.3.6.1.4.1.52642.1.4.1.2.1 |
portSecurityStaticPortIndexThe port index which port security is configured.
This is the first index into the portSecurityStaticAddressTable. Integer32 .1.3.6.1.4.1.52642.1.4.1.2.1.1 |
portSecurityStaticVlanIdThe Vlan ID associate with the port and the MAC address.
This is the second index into the portSecurityStaticAddressTable. Integer32 .1.3.6.1.4.1.52642.1.4.1.2.1.2 |
portSecurityStaticMacAddressThe MAC address of a station assigned to this port.
The index format of mac address '01:02:0a:0b:ff:ff' should be '1.2.10.11.255.255'
This is the third index into the portSecurityStaticAddressTable. Integer32 .1.3.6.1.4.1.52642.1.4.1.2.1.3 |
portSecurityStaticRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.4.1.2.1.4 |
portSecurityDynamicAddressTableThis table stores the dynamic MAC addresses which
are learned each port. SEQUENCE OF PortSecurityDynamicAddressEntry .1.3.6.1.4.1.52642.1.4.1.3 |
portSecurityDynamicAddressEntryThis table stores the dynamic MAC addresses which
are learned each port. PortSecurityDynamicAddressEntry .1.3.6.1.4.1.52642.1.4.1.3.1 |
portSecurityDynamicVlanIdThe Vlan ID associate with the port and the MAC address.
This is the third index into the portSecurityDynamicAddressTable.ro Integer32 .1.3.6.1.4.1.52642.1.4.1.3.1.1 |
portSecurityDynamicMacAddressThe MAC address of a station assigned to this port.This
is the second index into the portSecurityDynamicAddressTable.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.4.1.3.1.2 |
portSecurityDynamicPortNameThe port name which port security is configured.ro OCTET STRING .1.3.6.1.4.1.52642.1.4.1.3.1.3 |
stormControl OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.5 |
stormControlObject OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.5.1 |
stormControlUnicastTableThis table stores the port name and storm control
unicast mode,level and pps. SEQUENCE OF StormControlUnicastEntry .1.3.6.1.4.1.52642.1.5.1.1 |
stormControlUnicastEntryThis table stores the port name and storm control unicast mode and level. StormControlUnicastEntry .1.3.6.1.4.1.52642.1.5.1.1.1 |
stormControlUnicastPortNameThe name of interface which is configuredstorm
control.ro OCTET STRING .1.3.6.1.4.1.52642.1.5.1.1.1.1 |
stormControlUnicastModeThis indicates which unicast mode is configured whenstorm control is used.
1 PacketPerSecond.
2 Level.rw Enumeration .1.3.6.1.4.1.52642.1.5.1.1.1.2 |
stormControlUnicastLevelWhen unicast mode is configured Level,this
indicates the percentage of bandwith.
The valid range is (0.00-100.00).rw OCTET STRING .1.3.6.1.4.1.52642.1.5.1.1.1.3 |
stormControlUnicastPpsWhen unicast mode is configured PacketPerSecond,
this indicates the number of packet per second.rw Integer32 .1.3.6.1.4.1.52642.1.5.1.1.1.4 |
stormControlUnicastRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.5.1.1.1.5 |
stormControlBroadcastTableThis table stores the port name and storm control
broadcast mode,level and pps. SEQUENCE OF StormControlBroadcastEntry .1.3.6.1.4.1.52642.1.5.1.2 |
stormControlBroadcastEntryThis table stores the port name andstorm control broadcast mode and level. StormControlBroadcastEntry .1.3.6.1.4.1.52642.1.5.1.2.1 |
stormControlBroadcastPortNameThe name of interface which is configuredstorm
control.ro OCTET STRING .1.3.6.1.4.1.52642.1.5.1.2.1.1 |
stormControlBroadcastModeThis indicates which broadcast mode is configured whenstorm control is used.
1 PacketPerSecond.
2 Level.rw Enumeration .1.3.6.1.4.1.52642.1.5.1.2.1.2 |
stormControlBroadcastLevelWhen broadcast mode is configured Level,this
indicates the percentage of bandwith.
The valid range is (0.00-100.00).rw OCTET STRING .1.3.6.1.4.1.52642.1.5.1.2.1.3 |
stormControlBroadcastPpsWhen broadcast mode is configured PacketPerSecond,
this indicates the number of packet per second.rw Integer32 .1.3.6.1.4.1.52642.1.5.1.2.1.4 |
stormControlBroadcastRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.5.1.2.1.5 |
stormControlMulticastTableThis table stores the port name andstorm control
multicast mode and level. SEQUENCE OF StormControlMulticastEntry .1.3.6.1.4.1.52642.1.5.1.3 |
stormControlMulticastEntryThis table stores the port name andstorm control
multicast,level and pps. StormControlMulticastEntry .1.3.6.1.4.1.52642.1.5.1.3.1 |
stormControlMulticastPortNameThe name of interface which is configuredstorm control.ro OCTET STRING .1.3.6.1.4.1.52642.1.5.1.3.1.1 |
stormControlMulticastModeThis indicates which multicast mode is configured whenstorm control is used.
1 PacketPerSecond.
2 Level.rw Enumeration .1.3.6.1.4.1.52642.1.5.1.3.1.2 |
stormControlMulticastLevelWhen multicast mode is configured Level,this indicates the percentage
of bandwith. The valid range is (0.00-100.00).rw OCTET STRING .1.3.6.1.4.1.52642.1.5.1.3.1.3 |
stormControlMulticastPpsWhen multicast mode is configured PacketPerSecond, this indicates the
number of packet per second.rw Integer32 .1.3.6.1.4.1.52642.1.5.1.3.1.4 |
stormControlMulticastRowStatusThe status of this conceptual row.Now only realize CreateAndGo
and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.5.1.3.1.5 |
ntp OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.6 |
ntpObject OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.6.1 |
ntpStratumThis is an eight-bit integer indicating the stratum level
of the local clock, with values defined as follows:
0, unspecified
1, primary reference (e.g.,, radio clock)
2-255, secondary reference (via NTP)ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.1 |
ntpReferenceClockIpThe IP address of the reference clock ip address.ro IpAddress .1.3.6.1.4.1.52642.1.6.1.2 |
ntpFrequencyThe frequency of local clock relative to the primary
reference source.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.3 |
ntpPrecisionPrecision : This is a signed integer indicating the
precision relative to the reference clock ip.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.4 |
ntpReferenceTimeThis is the local time.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.5 |
ntpRootDelayThis is a signed fixed-point number indicating
the total roundtrip delay to the primary reference source
at the root of the synchronization subnet, in seconds.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.6 |
ntpRootDispersionRoot Dispersion : This is a signed fixed-point number
indicating the maximum error relative to the primary
reference source at the root of the synchronization
subnet, in seconds.Only positive values greater than
zero are possible.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.7 |
ntpPeerDispersionThis is a signed fixed-point number indicating
the maximum error of the local clock relative to
the primary reference source at the root of the
synchronization subnet.Only positive values
greater than zero are possible.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.8 |
ntpClockOffsetThis is a signed, fixed-point number indicating the offset
of the local clock relative to the primary clock, in seconds.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.9 |
ntpStabilityThis is a signed, fixed-point number indicating the stability
of the local clock relative to the primary clock, in seconds.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.10 |
ntpAssoTableThis table provides information about the peers and servers
with which the local NTP has associations. SEQUENCE OF NtpAssoEntry .1.3.6.1.4.1.52642.1.6.1.11 |
ntpAssoEntryEach association entry provides NTP information retrieved
from a particular initiative peer or server.Each peer or
server is identified by a unique association identifier.
Entries are automatically created when the user configures
the passive peer to unicast peer list or the passive server
to unicast server list. NtpAssoEntry .1.3.6.1.4.1.52642.1.6.1.11.1 |
ntpAssoRemoteIpAddressThe IP address of the initiative peer or server.ro IpAddress .1.3.6.1.4.1.52642.1.6.1.11.1.1 |
ntpAssoRefIdThe reference identifier of the peer or server.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.2 |
ntpAssoStratumThis is a integer indicating the stratum level
of the peer of server clock.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.3 |
ntpAssoWhenThis is a round second clock whose value change
from 1 to 60.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.4 |
ntpAssoPollThe interval at which the local host polls the peer.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.5 |
ntpAssoReachThis is a shift register of NTP which is used to
determine the reach abilityStatus of the peer.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.6 |
ntpAssoDelayThis is a signed fixed-point number indicating
the total roundtrip delay to the primary reference source
at the root of the synchronization subnet, in seconds.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.7 |
ntpAssoOffsetThis is a signed, fixed-point number indicating the offset
of the peer clock or server clock relative to the local
clock, in seconds.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.8 |
ntpAssoDispersionThis is a signed fixed-point number indicating
the maximum error of the peer or server clock
relative to the primary reference source.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.11.1.9 |
ntpUniPeerTableThis table provides ipaddress about the peer
with which the local NTP has associations.This
Table support create and destroy association
peer entry. SEQUENCE OF NtpUniPeerEntry .1.3.6.1.4.1.52642.1.6.1.12 |
ntpUniPeerEntryThis table provides ipaddress about the peer with which the local NTP
has associations.This table support create and destroy association peer
entry. NtpUniPeerEntry .1.3.6.1.4.1.52642.1.6.1.12.1 |
ntpUnicastPeerIpAddressThe IP address of the initiative peer.ro IpAddress .1.3.6.1.4.1.52642.1.6.1.12.1.1 |
ntpUnicastPeerKeyThe peer use which authentication key pair.rw Integer32 .1.3.6.1.4.1.52642.1.6.1.12.1.2 |
ntpUnicastPeerVersionThe NTP verion of the peer.rw Integer32 .1.3.6.1.4.1.52642.1.6.1.12.1.3 |
ntpUnicastPeerPreferThis indicates the NTP peer is a preferred peer.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.12.1.4 |
ntpUnicastPeerRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.6.1.12.1.5 |
ntpUniServerTableThis table provides ipaddress about the server with which the local NTP
has associations.This table support create and destroy association
server entry. SEQUENCE OF NtpUniServerEntry .1.3.6.1.4.1.52642.1.6.1.13 |
ntpUniServerEntryThis table provides ipaddress about the server with which the local NTP
has associations.This table support create and destroy association
server entry. NtpUniServerEntry .1.3.6.1.4.1.52642.1.6.1.13.1 |
ntpUnicastServerIpAddressThe IP address of the initiative server.ro IpAddress .1.3.6.1.4.1.52642.1.6.1.13.1.1 |
ntpUnicastServerKeyThe server use which authentication key pair.rw Integer32 .1.3.6.1.4.1.52642.1.6.1.13.1.2 |
ntpUnicastServerVersionThe NTP verion of the server.rw Integer32 .1.3.6.1.4.1.52642.1.6.1.13.1.3 |
ntpUnicastServerPreferThis indicates the NTP server is a preferred server.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.13.1.4 |
ntpUnicastServerRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.6.1.13.1.5 |
ntpLocalRefClockStratumThe stratum of local reference clock.If the value is 16, disable local reference clock.rw Integer32 .1.3.6.1.4.1.52642.1.6.1.14 |
ntpSysAuthenticateThis is a integer indicating that system support authentication.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.15 |
ntpBroadcastDelayThe broadcast delay of ntp broadcast mode.rw Integer32 .1.3.6.1.4.1.52642.1.6.1.16 |
ntpKeyTableThe table containing information of authentication key pair. SEQUENCE OF NtpKeyEntry .1.3.6.1.4.1.52642.1.6.1.17 |
ntpKeyEntryAn entry containing information of authentication key pair. NtpKeyEntry .1.3.6.1.4.1.52642.1.6.1.17.1 |
ntpKeyIDNTP authentication key ID Integer32 .1.3.6.1.4.1.52642.1.6.1.17.1.1 |
ntpKeyPairNTP authentication key pair.rw OCTET STRING .1.3.6.1.4.1.52642.1.6.1.17.1.2 |
ntpKeyRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.6.1.17.1.3 |
ntpTrustKeyTableThe table containing information of authentication key pair that trusted. SEQUENCE OF NtpTrustKeyEntry .1.3.6.1.4.1.52642.1.6.1.18 |
ntpTrustKeyEntryAn entry containing information of authentication key pair that trusted. NtpTrustKeyEntry .1.3.6.1.4.1.52642.1.6.1.18.1 |
ntpTrustKeyIDNTP authentication key ID Integer32 .1.3.6.1.4.1.52642.1.6.1.18.1.1 |
ntpTrustKeyTrustNTP authentication key pair trust.rw Integer32 .1.3.6.1.4.1.52642.1.6.1.18.1.2 |
ntpInterfaceReloadReload interfaces.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.19 |
ntpTimeResetStatisticNTP I/O statistics of time since reset.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.20 |
ntpRcvBufferStatisticNTP I/O statistics of receive buffers.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.21 |
ntpFreeRcvBufferStatisticNTP I/O statistics of free receive buffers.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.22 |
ntpUsedRcvBufferStatisticNTP I/O statistics of used receive buffers.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.23 |
ntpLowWaterRefillStatisticNTP I/O statistics of low water refills.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.24 |
ntpDroppedPktStatisticNTP I/O statistics of dropped packets.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.25 |
ntpIgnoredPktStatisticNTP I/O statistics of ignored packets.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.26 |
ntpReceivedPktStatisticNTP I/O statistics of received packets.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.27 |
ntpPktSentStatisticNTP I/O statistics of packets sent.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.28 |
ntpPktNotSentStatisticNTP I/O statistics of packets not sent.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.29 |
ntpInterruptsHandledStatisticNTP I/O statistics of interrupts handled.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.30 |
ntpReceivedByIntStatisticNTP I/O statistics of received by int.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.31 |
ntpAceTableThe table create the Access Control Entries (ACE) of a NTP server/peer. SEQUENCE OF NtpAceEntry .1.3.6.1.4.1.52642.1.6.1.32 |
ntpAceEntryAn entry containing information of NTP ACE. NtpAceEntry .1.3.6.1.4.1.52642.1.6.1.32.1 |
ntpAceIndexNTP ace list index. Integer32 .1.3.6.1.4.1.52642.1.6.1.32.1.1 |
ntpAceAddressIp address or hostname of NTP restrict peer.rw OCTET STRING .1.3.6.1.4.1.52642.1.6.1.32.1.2 |
ntpAceMaskMask of NTP restrict peer.
Default value is 255.255.255.255rw OCTET STRING .1.3.6.1.4.1.52642.1.6.1.32.1.3 |
ntpAceVersionIgnore these hosts if not the current NTP version.enable(1),disable(2).rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.4 |
ntpAceKodIf access is denied, send a kiss-of-death packet.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.5 |
ntpAceIgnoreIgnore all packets from host that match this entry.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.6 |
ntpAceNoqueryIgnore all NTP mode 6 and 7 packets from the source.
Time service is not affected.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.7 |
ntpAceNomodifyIgnore all NTP mode 6 and 7 packets
which attempt to modify the stateof the server.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.8 |
ntpAceNotrapDecline to provide mode 6 control message
trap service to matching hosts.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.9 |
ntpAceNoserverIgnore NTP packets whose mode is other than 6 or 7.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.10 |
ntpAceNopeerProvide stateless time service to polling hosts,
but do not allocate peer memory resources.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.11 |
ntpAceNotrustTreat these hosts normally in other respects,
but never use them as synchronization sources.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.12 |
ntpAceLimitedThese hosts are subject to limitation of
number of clients from the same net.rw Enumeration .1.3.6.1.4.1.52642.1.6.1.32.1.13 |
ntpAceRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.6.1.32.1.20 |
ntpRestrictTableThe table containing information of NTP current restrict list. SEQUENCE OF NtpRestrictEntry .1.3.6.1.4.1.52642.1.6.1.33 |
ntpRestrictEntryAn entry containing information of NTP restrict. NtpRestrictEntry .1.3.6.1.4.1.52642.1.6.1.33.1 |
ntpRestrictIndexNTP current restrict list index. Integer32 .1.3.6.1.4.1.52642.1.6.1.33.1.1 |
ntpRestrictAddressNTP current restrict address.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.33.1.2 |
ntpRestrictMaskNTP current restrict mask.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.33.1.3 |
ntpRestrictCountNTP current restrict count value.ro Integer32 .1.3.6.1.4.1.52642.1.6.1.33.1.4 |
ntpRestrictFlagNTP current restrict flags.ro OCTET STRING .1.3.6.1.4.1.52642.1.6.1.33.1.5 |
acl OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.7 |
aclData OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.7.1 |
aclGroupTableConfigure the match-order of number-acl group. SEQUENCE OF AclGroupEntry .1.3.6.1.4.1.52642.1.7.1.1 |
aclGroupEntryDefine the index of aclGroupTable. AclGroupEntry .1.3.6.1.4.1.52642.1.7.1.1.1 |
aclGroupIndexThe index of acl group.
MAC type :10001..20000
IP Extend type :20001..30000
IP type :30001..40000
IPv6 type :40001..50000
IPv6 Extend type :50001..60000
MLPS type :60001..70000
MPLS Extend type :70001..80000. Integer32 .1.3.6.1.4.1.52642.1.7.1.1.1.1 |
aclGroupNameThe name of acl group. Range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.1.1.2 |
aclGroupRuleNumThe count of rules in this acl group.ro Unsigned32 .1.3.6.1.4.1.52642.1.7.1.1.1.3 |
aclGroupRowStatusThe status of this row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.1.1.4 |
aclGroupDescriptionThe description of this acl group.Up to 100 characters.Range 0~100.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.1.1.5 |
aclMacRuleTableA table of MAC acl group.
If some objects of this table are not supported by some products,
these objects can't be created, changed and applied.
Default value of these objects will be returned when they are read. SEQUENCE OF AclMacRuleEntry .1.3.6.1.4.1.52642.1.7.1.2 |
aclMacRuleEntryMAC acl group information. AclMacRuleEntry .1.3.6.1.4.1.52642.1.7.1.2.1 |
aclMacGroupIndexThe index of MAC-based acl group.Range is 10001~30000 and 50001~60000. Integer32 (10001..30000|50001..60000) .1.3.6.1.4.1.52642.1.7.1.2.1.1 |
aclMacRuleIndexThe rule index of MAC-based acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.2.1.2 |
aclMacActThe action of MAC acl rule.
(1) permit.
(2) deny.rw RuleAction .1.3.6.1.4.1.52642.1.7.1.2.1.3 |
aclMacSrcMacSource MAC of MAC acl rule.
If you do not want to use this filter,
set this item with any valid value
and set aclMacSrcMacWild 'FFFF.FFFF.FFFF'.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.2.1.4 |
aclMacSrcMacWildSource MAC wildcard of MAC acl rule.
If you do not want to use this filter,
set aclMacSrcMac with any valid value
and set this item 'FFFF.FFFF.FFFF'.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.2.1.5 |
aclMacDestMacDestination MAC of MAC acl rule.
If you do not want to use this filter,
set this item with any valid value
and set aclMacDestMacWild 'FFFF.FFFF.FFFF'.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.2.1.6 |
aclMacDestMacWildDestination MAC wildcard of MAC acl rule.
If you do not want to use this filter,
set aclMacDestMac with any valid value
and set this item 'FFFF.FFFF.FFFF'.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.2.1.7 |
aclMacProtocolEther type in decimal/hexadecimal, ranging in <0x0-0xffff>.
(aclMacProtocol = 0, aclMacProtocolWild = 0xffff) means any protocols.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.2.1.8 |
aclMacProtocolWildEther type wildcard in decimal/hexadecimal, ranging in <0x0-0xffff>,
reversely encoded.
(aclMacProtocol = 0, aclMacProtocolWild = 0xffff) means any protocols.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.2.1.9 |
aclMacTypeThe type of protocol
nouse(0)
eth2(1)
sap(2)
snap(3)rwobsolete Integer32 .1.3.6.1.4.1.52642.1.7.1.2.1.10 |
aclMacVlanIdThe vlan id of MAC acl rule.Range 0~4094.
nouse(0)rw Integer32 .1.3.6.1.4.1.52642.1.7.1.2.1.11 |
aclMacInnerVlanIdThe inner vlan id of MAC acl rule. Range 0~4094
nouse(0)rw Integer32 .1.3.6.1.4.1.52642.1.7.1.2.1.12 |
aclMacCosVlan priority of MAC acl rule.Range 0~8
nouse(8).rw Integer32 .1.3.6.1.4.1.52642.1.7.1.2.1.13 |
aclMacInnerCosInner vlan priority of MAC acl rule.Range 0~8.
nouse(8).rw Integer32 .1.3.6.1.4.1.52642.1.7.1.2.1.14 |
aclMacTimeRangeNameThe Time-range of MAC acl rule.Range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.2.1.15 |
aclMacRowStatusThe status of this row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.2.1.30 |
aclIpRuleTableConfigure the rule for ip acl group. SEQUENCE OF AclIpRuleEntry .1.3.6.1.4.1.52642.1.7.1.3 |
aclIpRuleEntryDefine the index of aclIpRuleTable. AclIpRuleEntry .1.3.6.1.4.1.52642.1.7.1.3.1 |
aclIpGroupIndexThe index of ip acl group. Range 20001~40000. Integer32 .1.3.6.1.4.1.52642.1.7.1.3.1.1 |
aclIpRuleIndexThe rule index of ip acl rule.Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.3.1.2 |
aclIpActThe action of ip acl rule.
(1) permit.
(2) deny.rw RuleAction .1.3.6.1.4.1.52642.1.7.1.3.1.3 |
aclIpProtocolThe protocol-type of Ip acl group.
<0-255> Protocol number
Icmp Internet Control Message Protocol(1)
igmp Internet Group Management Protocol(2)
ospf OSPF routing protocol(89)
tcp Transmission Control Protocol (6)
udp User Datagram Protocol (17)
nouse Do not use this filter(256)rw Integer32 .1.3.6.1.4.1.52642.1.7.1.3.1.4 |
aclIpSrcIpSource IP-address of ip acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.3.1.5 |
aclIpSrcWildSource IP-address wild of ip acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.3.1.6 |
aclIpDestIpDestination IP-address of ip acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.3.1.7 |
aclIpDestWildDestination IP-address wild of ip acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.3.1.8 |
aclIpPrecedenceThe value of Precedence.8 means do not use this filter.Range 0~8.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIpDscp is setted.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.3.1.9 |
aclIpDscpThe value of DSCP.64 means do not use this filter.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIpPrecedence is setted.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.3.1.10 |
aclIpFragmentsThe flag of matching fragmented packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.3.1.11 |
aclIpRoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.3.1.12 |
aclIpOptionsThe flag of matching packet with ip option. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.3.1.13 |
aclIpTimeRangeNameThe Time-range of Ip acl rule.String length range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.3.1.14 |
aclIpRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.3.1.16 |
aclTcpRuleTableConfigure the rule for tcp acl group. SEQUENCE OF AclTcpRuleEntry .1.3.6.1.4.1.52642.1.7.1.4 |
aclTcpRuleEntryDefine the index of hh3cAclTcpRuleTable. AclTcpRuleEntry .1.3.6.1.4.1.52642.1.7.1.4.1 |
aclTcpGroupIndexThe index of tcp acl group. Range 20001~40000. Integer32 .1.3.6.1.4.1.52642.1.7.1.4.1.1 |
aclTcpRuleIndexThe rule index of tcp acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.4.1.2 |
aclTcpActThe action of tcp acl rule.
(1) permit.
(2) deny.rw RuleAction .1.3.6.1.4.1.52642.1.7.1.4.1.3 |
aclTcpSrcIpSource IP-address of tcp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.4.1.4 |
aclTcpSrcWildSource IP-address wild of tcp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.4.1.5 |
aclTcpDestIpDestination IP-address of tcp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.4.1.6 |
aclTcpDestWildDestination IP-address wild of tcp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.4.1.7 |
aclTcpPrecedenceThe value of Precedence.8 means do not use this filter.Range 0~8.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclTcpDscp is setted.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.4.1.8 |
aclTcpDscpThe value of DSCP.64 means do not use this filter.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclTcpPrecedence is setted.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.4.1.9 |
aclTcpFragmentsThe flag of matching fragmented packet. True(1),False(2).
This node can not be setted true for aclTcpSrcOp or aclTcpDestOp is setted.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.10 |
aclTcpRoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.11 |
aclTcpOptionsThe flag of matching packet with ip option. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.12 |
aclTcpSrcOpThe source port's operator of tcp acl group.
This node can not be setted if aclTcpFragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.4.1.13 |
aclTcpSrcPort1The fourth layer source port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.4.1.14 |
aclTcpSrcPort2The fourth layer source port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.4.1.15 |
aclTcpDestOpThe destination port's operator of tcp acl group.
This node can not be setted if aclTcpFragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.4.1.16 |
aclTcpDestPort1The fourth layer destination port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.4.1.17 |
aclTcpDestPort2The fourth layer destination port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.4.1.18 |
aclTcpFlagOpThe tcp-flags' operator of tcp acl group.for example, established tcp packet with ack or rst flag setted, set this node matchAny(0) and set aclTcpFlagAck and aclTcpFlagRst can filter established tcp packet.
matchAny(0),
matchAll(1),
invalid(2).rw Enumeration .1.3.6.1.4.1.52642.1.7.1.4.1.19 |
aclTcpFlagUrgThe tcp-urg flag of tcp acl group. True(1),False(2).
TCP protocol URG Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.20 |
aclTcpFlagAckThe tcp-ack flag of tcp acl group.
TCP protocol ACK Packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.21 |
aclTcpFlagPshThe tcp-psh flag of tcp acl group. True(1),False(2).
TCP protocol PSH Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.22 |
aclTcpFlagRstThe tcp-rst flag of tcp acl group. True(1),False(2).
TCP protocol RST Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.23 |
aclTcpFlagSynThe tcp-syn flag of tcp acl group. True(1),False(2).
TCP protocol SYN Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.24 |
aclTcpFlagFinThe tcp-fin flag of tcp acl group. True(1),False(2).
TCP protocol FIN Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.25 |
aclTcpTimeRangeNameThe Time-range of tcp acl rule.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.4.1.26 |
aclTcpRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.4.1.28 |
aclUdpRuleTableConfigure the rule for udp acl group. SEQUENCE OF AclUdpRuleEntry .1.3.6.1.4.1.52642.1.7.1.5 |
aclUdpRuleEntryDefine the index of aclUdpRuleTable. AclUdpRuleEntry .1.3.6.1.4.1.52642.1.7.1.5.1 |
aclUdpGroupIndexThe index of udp acl group. Range 20001~40000. Integer32 .1.3.6.1.4.1.52642.1.7.1.5.1.1 |
aclUdpRuleIndexThe rule index of udp acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.5.1.2 |
aclUdpActThe action of udp acl rule.
(1) permit.
(2) denyrw RuleAction .1.3.6.1.4.1.52642.1.7.1.5.1.3 |
aclUdpSrcIpSource IP-address of udp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.5.1.4 |
aclUdpSrcWildSource IP-address wild of udp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.5.1.5 |
aclUdpDestIpDestination IP-address of udp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.5.1.6 |
aclUdpDestWildDestination IP-address wild of udp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.5.1.7 |
aclUdpPrecedenceThe value of Precedence.8 means do not use this filter.Range 0~8.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclUdpDscp is setted.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.5.1.8 |
aclUdpDscpThe value of DSCP.64 means do not use this filter.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclUdpPrecedence is setted.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.5.1.9 |
aclUdpFragmentsThe flag of matching fragmented packet. True(1),False(2).
This node can not be setted true for aclUdpSrcOp or aclUdpDestOp is setted.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.5.1.10 |
aclUdpRoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.5.1.11 |
aclUdpOptionsThe flag of matching packet with ip option. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.5.1.12 |
aclUdpSrcOpThe source port's operator of udp acl group.
This node can not be setted if aclUdpFragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.5.1.13 |
aclUdpSrcPort1The fourth layer source port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.5.1.14 |
aclUdpSrcPort2The fourth layer source port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.5.1.15 |
aclUdpDestOpThe destination port's operator of udp acl group.
This node can not be setted if aclUdpFragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.5.1.16 |
aclUdpDestPort1The fourth layer destination port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.5.1.17 |
aclUdpDestPort2The fourth layer destination port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.5.1.18 |
aclUdpTimeRangeNameThe Time-range of udp acl rule. Range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.5.1.19 |
aclUdpRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.5.1.21 |
aclIcmpRuleTableConfigure the rule for icmp acl group. SEQUENCE OF AclIcmpRuleEntry .1.3.6.1.4.1.52642.1.7.1.6 |
aclIcmpRuleEntryDefine the index of aclIcmpRuleTable. AclIcmpRuleEntry .1.3.6.1.4.1.52642.1.7.1.6.1 |
aclIcmpGroupIndexThe index of icmp acl group. Range 20001~40000. Integer32 .1.3.6.1.4.1.52642.1.7.1.6.1.1 |
aclIcmpRuleIndexThe rule index of icmp acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.6.1.2 |
aclIcmpActThe action of icmp acl rule.
(1) permit.
(2) denyrw RuleAction .1.3.6.1.4.1.52642.1.7.1.6.1.3 |
aclIcmpSrcIpSource IP-address of icmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.6.1.4 |
aclIcmpSrcWildSource IP-address wild of icmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.6.1.5 |
aclIcmpDestIpDestination IP-address of icmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.6.1.6 |
aclIcmpDestWildDestination IP-address wild of icmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.6.1.7 |
aclIcmpPrecedenceThe value of Precedence.8 means do not use this filter.Range 0~8.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIcmpDscp is setted.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.6.1.8 |
aclIcmpDscpThe value of DSCP.64 means do not use this filter.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIcmpPrecedence is setted.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.6.1.9 |
aclIcmpFragmentsThe flag of matching fragmented packet.
This node can not be setted true if aclIcmpType is setted. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.6.1.10 |
aclIcmpRoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.6.1.11 |
aclIcmpOptionsThe flag of matching packet with ip option. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.6.1.12 |
aclIcmpTypeThe type of ICMP packet.
INTEGER<0-256> ICMP type
echo Type=8, Code=0
echo-reply Type=0, Code=0
fragmentneed-DFset Type=3, Code=4
host-redirect Type=5, Code=1
host-tos-redirect Type=5, Code=3
host-unreachable Type=3, Code=1
information-reply Type=16, Code=0
information-request Type=15, Code=0
net-redirect Type=5, Code=0
net-tos-redirect Type=5, Code=2
net-unreachable Type=3, Code=0
parameter-problem Type=12, Code=0
port-unreachable Type=3, Code=3
protocol-unreachable Type=3, Code=2
reassembly-timeout Type=11, Code=1
source-quench Type=4, Code=0
source-route-failed Type=3, Code=5
timestamp-reply Type=14, Code=0
timestamp-request Type=13, Code=0
ttl-exceeded Type=11, Code=0
nouse 256
This node can not be setted if aclIcmpFragments is true.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.6.1.13 |
aclIcmpCodeThe code of ICMP packet.INTEGER<0-256>
echo Type=8, Code=0
echo-reply Type=0, Code=0
fragmentneed-DFset Type=3, Code=4
host-redirect Type=5, Code=1
host-tos-redirect Type=5, Code=3
host-unreachable Type=3, Code=1
information-reply Type=16, Code=0
information-request Type=15, Code=0
net-redirect Type=5, Code=0
net-tos-redirect Type=5, Code=2
net-unreachable Type=3, Code=0
parameter-problem Type=12, Code=0
port-unreachable Type=3, Code=3
protocol-unreachable Type=3, Code=2
reassembly-timeout Type=11, Code=1
source-quench Type=4, Code=0
source-route-failed Type=3, Code=5
timestamp-reply Type=14, Code=0
timestamp-request Type=13, Code=0
ttl-exceeded Type=11, Code=0
nouse 256
This node can not be setted if aclIcmpType is not setted.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.6.1.14 |
aclIcmpTimeRangeNameThe Time-range of icmp acl rule. Range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.6.1.15 |
aclIcmpRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.6.1.17 |
aclIgmpRuleTableConfigure the rule for igmp acl group. SEQUENCE OF AclIgmpRuleEntry .1.3.6.1.4.1.52642.1.7.1.7 |
aclIgmpRuleEntryDefine the index of aclIgmpRuleTable. AclIgmpRuleEntry .1.3.6.1.4.1.52642.1.7.1.7.1 |
aclIgmpGroupIndexThe index of igmp acl group. Range 20001~40000. Integer32 .1.3.6.1.4.1.52642.1.7.1.7.1.1 |
aclIgmpRuleIndexThe rule index of igmp acl group.Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.7.1.2 |
aclIgmpActThe action of igmp acl rule.
(1) permit.
(2) denyrw RuleAction .1.3.6.1.4.1.52642.1.7.1.7.1.3 |
aclIgmpSrcIpSource IP-address of igmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.7.1.4 |
aclIgmpSrcWildSource IP-address wild of igmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.7.1.5 |
aclIgmpDestIpDestination IP-address of igmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.7.1.6 |
aclIgmpDestWildDestination IP-address wild of igmp acl group.rw IpAddress .1.3.6.1.4.1.52642.1.7.1.7.1.7 |
aclIgmpPrecedenceThe value of Precedence.8 means do not use this filter.Range 0~8.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIgmpDscp is setted.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.7.1.8 |
aclIgmpDscpThe value of DSCP.64 means do not use this filter.
DSCP and Precedence both use IP TOS segment.This node can not be setted for aclIgmpPrecedence is setted.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.7.1.9 |
aclIgmpFragmentsThe flag of matching fragmented packet.
This node can not be setted true if aclIgmpType is setted. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.7.1.10 |
aclIgmpRoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.7.1.11 |
aclIgmpOptionsThe flag of matching packet with ip option.True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.7.1.12 |
aclIgmpTypeThe type of ICMP packet.
0 precedence
17 host query
18 host report
19 dvmrp
20 pim
21 trace
22 v2 report
23 v2 leave
30 mtrace response
31 mtrace
34 v3 report
256 nouse
This node can not be setted if aclIgmpFragments is true.rw Enumeration .1.3.6.1.4.1.52642.1.7.1.7.1.13 |
aclIgmpTimeRangeNameThe Time-range of igmp acl rule.Range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.7.1.14 |
aclIgmpRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.7.1.16 |
aclMplsMacRuleTableA table of MPLS MAC acl group.
If some objects of this table are not supported by some products,
these objects can't be created, changed and applied.
Default value of these objects will be returned when they are read. SEQUENCE OF AclMplsMacRuleEntry .1.3.6.1.4.1.52642.1.7.1.8 |
aclMplsMacRuleEntryMPLS MAC acl group information. AclMplsMacRuleEntry .1.3.6.1.4.1.52642.1.7.1.8.1 |
aclMplsMacGroupIndexThe index of MPLS MAC-based acl group. Range 70001 ~ 80000. Integer32 .1.3.6.1.4.1.52642.1.7.1.8.1.1 |
aclMplsMacRuleIndexThe rule index of MPLS MAC-based acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.8.1.2 |
aclMplsMacActThe action of MPLS MAC acl rule.
(1) permit.
(2) deny.rw RuleAction .1.3.6.1.4.1.52642.1.7.1.8.1.3 |
aclMplsMacSrcMacSource MAC of MPLS MAC acl rule.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.8.1.4 |
aclMplsMacSrcMacWildSource MAC wildcard of MPLS MAC acl rule.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.8.1.5 |
aclMplsMacDestMacDestination MAC of MAC acl rule.
If you do not want to use this filter,
set this item and aclMacDestMacWild 'FF:FF:FF:FF:FF:FF'.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.8.1.6 |
aclMplsMacDestMacWildDestination MAC wildcard of MAC acl rule. If you do not want to use
this filter, set this item and aclMacDestMac 'FF:FF:FF:FF:FF:FF'.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.8.1.7 |
aclMplsMacTypeThe type of protocol
nouse(0)
eth2(1)
sap(2)
snap(3)rw Integer32 .1.3.6.1.4.1.52642.1.7.1.8.1.8 |
aclMplsMacVlanIdThe vlan id of MAC acl rule.Range 0~4094.
nouse(0)rw Integer32 .1.3.6.1.4.1.52642.1.7.1.8.1.9 |
aclMplsMacInnerVlanIdThe inner vlan id of MAC acl rule.
nouse(0)rw Integer32 .1.3.6.1.4.1.52642.1.7.1.8.1.10 |
aclMplsMacCosVlan priority of MAC acl rule.Range 0~8
nouse(8).rw Integer32 .1.3.6.1.4.1.52642.1.7.1.8.1.11 |
aclMplsMacInnerCosInner vlan priority of MAC acl rule.
nouse(8).rw Integer32 .1.3.6.1.4.1.52642.1.7.1.8.1.12 |
aclMplsMacTimeRangeNameThe Time-range of MAC acl rule.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.8.1.13 |
aclMplsMacRowStatusThe status of this row.Now only realize CreateAndGo and Destroy and Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.8.1.20 |
aclMplsLabelRuleTableConfigure the rule for Mpls Label acl group. SEQUENCE OF AclMplsLabelRuleEntry .1.3.6.1.4.1.52642.1.7.1.9 |
aclMplsLabelRuleEntryDefine the index of acl Mpls Label RuleTable. AclMplsLabelRuleEntry .1.3.6.1.4.1.52642.1.7.1.9.1 |
aclMplsLabelGroupIndexThe index of MplsLabel acl group. Range 60001~80000. Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.1 |
aclMplsLabelRuleIndexThe rule index of MplsLabel acl rule.Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.2 |
aclMplsLabelActThe action of MplsLabel acl rule.
(1) permit.
(2) deny.rw RuleAction .1.3.6.1.4.1.52642.1.7.1.9.1.3 |
aclMplsLabelLayerThe layer number of MPLS labels.Range is <1-4>.
Set 1 means match MPLS packets with more than
(or equal to) one layer MPLS label.
Set 2 means match MPLS packets with more than
(or equal to) two layer MPLS label.
Set 3 means match MPLS packets with more than
(or equal to) three layer MPLS label.
Set 4 means match MPLS packets with more than
(or equal to) four layer MPLS label.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.4 |
aclMplsLabel1ValueThe mpls label1 value in in decimal system.
Range is 0~1048575.Default value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.5 |
aclMplsLabel1WildMPLS label wildcard in hexadecimal system.
Range is string 0~fffff.
Default wild value is fffff, means any.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.9.1.6 |
aclMplsLabel1ExpThe exp value of the MPLS label.Range of exp is <0-7>.
8 means do not use.Default value is 8.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.7 |
aclMplsLabel1TtlThe ttl value of the MPLS label.Range of ttl is <0-255>.
256 means do not use.Default value is 256.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.8 |
aclMplsLabel2ValueThe mpls label value in in decimal system.
Range is 0~1048575.Default value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.9 |
aclMplsLabel2WildMPLS label wildcard in hexadecimal system.
Range is string 0~fffff.
Defalut wild value is fffff, means any.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.9.1.10 |
aclMplsLabel2ExpThe exp value of the MPLS label.Range of exp is <0-7>.
8 means do not use.Default value is 8.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.11 |
aclMplsLabel2TtlThe ttl value of the MPLS label.Range of ttl is <0-255>.
256 means do not use.Default value is 256.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.12 |
aclMplsLabel3ValueThe mpls label value in in decimal system.
Range is 0~1048575.Default value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.13 |
aclMplsLabel3WildMPLS label wildcard in hexadecimal system.
Range is string 0~fffff.
Default wild value is fffff, means any.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.9.1.14 |
aclMplsLabel3ExpThe exp value of the MPLS label.Range of exp is <0-7>.
8 means do not use.Default value is 8.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.15 |
aclMplsLabel3TtlThe ttl value of the MPLS label.Range of ttl is <0-255>.
256 means do not use.Default value is 256.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.16 |
aclMplsLabel4ValueThe mpls label value in in decimal system.
Range is 0~1048575.Default value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.17 |
aclMplsLabel4WildMPLS label wildcard in hexadecimal system.
Range is string 0~fffff.
Default wild value is fffff, means any.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.9.1.18 |
aclMplsLabel4ExpThe exp value of the MPLS label.Range of exp is <0-7>.
8 means do not use.Default value is 8.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.19 |
aclMplsLabel4TtlThe ttl value of the MPLS label.Range of ttl is <0-255>.
256 means do not use.Default value is 256.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.9.1.20 |
aclMplsLabelSkBottomSet whether the topmost label as bottom of label stack.
True(1), means matching MPLS packets with
label layer num equal to aclMplsLabelLayer.
False(2), means matching MPLS packets with
label layer num more than aclMplsLabelLayer.
Default value is False.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.9.1.21 |
aclMplsLabelTimeRangeNameThe Time-range of used by the MPLS filter rule.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.9.1.22 |
aclMplsLabelRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.9.1.25 |
aclIpv6RuleTableConfigure the rule for ipv6 acl group. SEQUENCE OF AclIpv6RuleEntry .1.3.6.1.4.1.52642.1.7.1.10 |
aclIpv6RuleEntryDefine the index of aclIpv6RuleTable. AclIpv6RuleEntry .1.3.6.1.4.1.52642.1.7.1.10.1 |
aclIpv6GroupIndexThe index of ipv6 acl group. Range 40001~60000. Integer32 .1.3.6.1.4.1.52642.1.7.1.10.1.1 |
aclIpv6RuleIndexThe rule index of ipv6 acl rule.Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.10.1.2 |
aclIpv6ActThe action of ipv6 acl rule.
(1) permit.
(2) deny.rw RuleAction .1.3.6.1.4.1.52642.1.7.1.10.1.3 |
aclIpv6ProtocolThe protocol-type of Ipv6 acl group.
<0-255> Protocol number
Icmpv6 Internet Control Message Protocol(58)
ospf OSPF routing protocol(89)
tcp Transmission Control Protocol (6)
udp User Datagram Protocol (17)
nouse Do not use this filter(256)rw Integer32 .1.3.6.1.4.1.52642.1.7.1.10.1.4 |
aclIpv6SrcIpv6Source IPv6-address of ipv6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.10.1.5 |
aclIpv6SrcPrefixLenSource IPv6-address prefix length of ipv6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.10.1.6 |
aclIpv6DestIpv6Destination IPv6-address of ipv6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.10.1.7 |
aclIpv6DestPrefixLenDestination IPv6-address prefix length of ipv6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.10.1.8 |
aclIpv6FlowLabelThe value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.10.1.9 |
aclIpv6DscpThe value of DSCP.64 means do not use this filter.Range 0~64.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.10.1.10 |
aclIpv6FragmentsThe flag of matching fragmented packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.10.1.11 |
aclIpv6RoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.10.1.12 |
aclIpv6OptionsThe flag of matching packet with ipv6 option. True(1),False(2).rwobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.10.1.13 |
aclIpv6TimeRangeNameThe Time-range of Ipv6 acl rule.String length range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.10.1.14 |
aclIpv6RowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.10.1.16 |
aclTcp6RuleTableConfigure the rule for tcp6 acl group. SEQUENCE OF AclTcp6RuleEntry .1.3.6.1.4.1.52642.1.7.1.11 |
aclTcp6RuleEntryDefine the index of aclTcp6RuleTable. AclTcp6RuleEntry .1.3.6.1.4.1.52642.1.7.1.11.1 |
aclTcp6GroupIndexThe index of tcp6 acl group. Range 40001~60000. Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.1 |
aclTcp6RuleIndexThe rule index of tcp6 acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.2 |
aclTcp6ActThe action of tcp6 acl rule.
(1) permit.
(2) deny.rw RuleAction .1.3.6.1.4.1.52642.1.7.1.11.1.3 |
aclTcp6SrcIpv6Source IPv6-address of tcp6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.11.1.4 |
aclTcp6SrcPrefixLenSource IPv6-address prefix length of tcp6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.5 |
aclTcp6DestIpv6Destination IPv6-address of tcp6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.11.1.6 |
aclTcp6DestPrefixLenDestination IPv6-address prefix length of tcp6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.7 |
aclTcp6FlowLabelThe value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.8 |
aclTcp6DscpThe value of DSCP.64 means do not use this filter.Range 0~64.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.11.1.9 |
aclTcp6FragmentsThe flag of matching fragmented packet. True(1),False(2).
This node can not be setted true for aclTcp6SrcOp or aclTcp6DestOp is setted.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.10 |
aclTcp6RoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.11 |
aclTcp6OptionsThe flag of matching packet with ipv6 option. True(1),False(2).rwobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.12 |
aclTcp6SrcOpThe source port's operator of tcp6 acl group.
This node can not be setted if aclTcp6Fragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.11.1.13 |
aclTcp6SrcPort1The fourth layer source port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.14 |
aclTcp6SrcPort2The fourth layer source port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.15 |
aclTcp6DestOpThe destination port's operator of tcp6 acl group.
This node can not be setted if aclTcp6Fragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.11.1.16 |
aclTcp6DestPort1The fourth layer destination port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.17 |
aclTcp6DestPort2The fourth layer destination port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.11.1.18 |
aclTcp6FlagOpThe tcp-flags' operator of tcp6 acl group.
for example, established tcp packet with ack or rst flag setted,
set this node matchAny(0) and set aclTcp6FlagAck and aclTcp6FlagRst
can filter established tcp packet.
matchAny(0),
matchAll(1),
invalid(2).rw Enumeration .1.3.6.1.4.1.52642.1.7.1.11.1.19 |
aclTcp6FlagUrgThe tcp-urg flag of tcp6 acl group. True(1),False(2).
TCP protocol URG Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.20 |
aclTcp6FlagAckThe tcp-ack flag of tcp6 acl group.
TCP protocol ACK Packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.21 |
aclTcp6FlagPshThe tcp-psh flag of tcp6 acl group. True(1),False(2).
TCP protocol PSH Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.22 |
aclTcp6FlagRstThe tcp-rst flag of tcp6 acl group. True(1),False(2).
TCP protocol RST Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.23 |
aclTcp6FlagSynThe tcp-syn flag of tcp6 acl group. True(1),False(2).
TCP protocol SYN Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.24 |
aclTcp6FlagFinThe tcp-fin flag of tcp6 acl group. True(1),False(2).
TCP protocol FIN Packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.25 |
aclTcp6TimeRangeNameThe Time-range of tcp6 acl rule.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.11.1.26 |
aclTcp6RowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.11.1.28 |
aclUdp6RuleTableConfigure the rule for udp6 acl group. SEQUENCE OF AclUdp6RuleEntry .1.3.6.1.4.1.52642.1.7.1.12 |
aclUdp6RuleEntryDefine the index of aclUdp6RuleTable. AclUdp6RuleEntry .1.3.6.1.4.1.52642.1.7.1.12.1 |
aclUdp6GroupIndexThe index of udp6 acl group. Range 40001~60000. Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.1 |
aclUdp6RuleIndexThe rule index of udp6 acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.2 |
aclUdp6ActThe action of udp6 acl rule.
(1) permit.
(2) denyrw RuleAction .1.3.6.1.4.1.52642.1.7.1.12.1.3 |
aclUdp6SrcIpv6Source IPv6-address of udp6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.12.1.4 |
aclUdp6SrcPrefixLenSource IPv6-address prefix length of udp6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.5 |
aclUdp6DestIpv6Destination IPv6-address of udp6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.12.1.6 |
aclUdp6DestPrefixLenDestination IPv6-address prefix length of udp6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.7 |
aclUdp6FlowLabelThe value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.8 |
aclUdp6DscpThe value of DSCP.64 means do not use this filter.Range 0~64.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.12.1.9 |
aclUdp6FragmentsThe flag of matching fragmented packet. True(1),False(2).
This node can not be setted true for aclUdp6SrcOp or aclUdp6DestOp is setted.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.12.1.10 |
aclUdp6RoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.12.1.11 |
aclUdp6OptionsThe flag of matching packet with ipv6 option. True(1),False(2).rwobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.12.1.12 |
aclUdp6SrcOpThe source port's operator of udp6 acl group.
This node can not be setted if aclUdp6Fragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.12.1.13 |
aclUdp6SrcPort1The fourth layer source port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.14 |
aclUdp6SrcPort2The fourth layer source port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.15 |
aclUdp6DestOpThe destination port's operator of udp6 acl group.
This node can not be setted if aclUdp6Fragments is true.
eq(0),
gt(2),
lt(3),
range(4),
invalid(5)rw PortOp .1.3.6.1.4.1.52642.1.7.1.12.1.16 |
aclUdp6DestPort1The fourth layer destination port1. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.17 |
aclUdp6DestPort2The fourth layer destination port2. Range 0~65535.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.12.1.18 |
aclUdp6TimeRangeNameThe Time-range of udp6 acl rule. Range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.12.1.19 |
aclUdp6RowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.12.1.21 |
aclIcmp6RuleTableConfigure the rule for icmp6 acl group. SEQUENCE OF AclIcmp6RuleEntry .1.3.6.1.4.1.52642.1.7.1.13 |
aclIcmp6RuleEntryDefine the index of aclIcmp6RuleTable. AclIcmp6RuleEntry .1.3.6.1.4.1.52642.1.7.1.13.1 |
aclIcmp6GroupIndexThe index of icmp6 acl group. Range 40001~60000. Integer32 .1.3.6.1.4.1.52642.1.7.1.13.1.1 |
aclIcmp6RuleIndexThe rule index of icmp6 acl group. Range 1~131071. Integer32 .1.3.6.1.4.1.52642.1.7.1.13.1.2 |
aclIcmp6ActThe action of icmp6 acl rule.
(1) permit.
(2) denyrw RuleAction .1.3.6.1.4.1.52642.1.7.1.13.1.3 |
aclIcmp6SrcIpv6Source IPv6-address of icmp6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.13.1.4 |
aclIcmp6SrcPrefixLenSource IPv6-address prefix length of icmp6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.13.1.5 |
aclIcmp6DestIpv6Destination IPv6-address of icmp6 acl group.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.13.1.6 |
aclIcmp6DestPrefixLenDestination IPv6-address prefix length of icmp6 acl group.Range 0~128rw Integer32 .1.3.6.1.4.1.52642.1.7.1.13.1.7 |
aclIcmp6FlowLabelThe value of FlowLabel.1048576 means do not use this filter.Range 0~1048576.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.13.1.8 |
aclIcmp6DscpThe value of DSCP.64 means do not use this filter.Range 0~64.rw DSCPValue .1.3.6.1.4.1.52642.1.7.1.13.1.9 |
aclIcmp6FragmentsThe flag of matching fragmented packet.
This node can not be setted true if aclIcmp6Type is setted. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.13.1.10 |
aclIcmp6RoutedThe flag of matching routed packet. True(1),False(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.13.1.11 |
aclIcmp6OptionsThe flag of matching packet with ipv6 option. True(1),False(2).rwobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.13.1.12 |
aclIcmp6TypeThe type of ICMPv6 packet.Range 0~256.
This node can not be setted if aclIcmp6Fragments is true.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.13.1.13 |
aclIcmp6CodeThe code of ICMPv6 packet.Range 0~256.
This node can not be setted if aclIcmp6Type is not setted.rw Integer32 .1.3.6.1.4.1.52642.1.7.1.13.1.14 |
aclIcmp6TimeRangeNameThe Time-range of icmp6 acl rule. Range 0~20.rw OCTET STRING .1.3.6.1.4.1.52642.1.7.1.13.1.15 |
aclIcmp6RowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.7.1.13.1.17 |
qos OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8 |
globalQos OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.1 |
globalQosEnableEnable/disable qos globally. enable(1),disable(2).rw Enumeration .1.3.6.1.4.1.52642.1.8.1.1 |
globalQosFlowFirstSet 'true(1)' for flow policer first, 'false(2)' for port policer first.
Default value is false(2).rw Enumeration .1.3.6.1.4.1.52642.1.8.1.2 |
globalQosResetMapObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.1.3 |
globalQosResetDomainMapTableReset configuration of qos maping table in specified domain. SEQUENCE OF GlobalQosResetDomainMapEntry .1.3.6.1.4.1.52642.1.8.1.3.1 |
globalQosResetDomainMapEntryEntry of globalQosResetDomainMapTable. GlobalQosResetDomainMapEntry .1.3.6.1.4.1.52642.1.8.1.3.1.1 |
globalQosResetDomainMapDomainQos domain.Range is <0-7>. Integer32 .1.3.6.1.4.1.52642.1.8.1.3.1.1.1 |
globalQosResetDomainMapTypeRestore the whole running map table to system default table.
Set the value to restore related table.
cosPriColor(1) Restore the COS-to-Priority/Color map
dscpPriColor(2) Restore dscp-priority-color map
expPriColor(3) Restore the exp-to-priority/color map
ipPrecPriColor(4) Restore the IP Precedence to Pri/Color map
priColorCos(5) Restore PRI_COLOR-to-COS map
priColorDscp(6) Restore PRI_COLOR-to-DSCP map
priColorExp(7) Restore PRI_COLOR-to-EXP map
The get of this value alway return 0rw Enumeration .1.3.6.1.4.1.52642.1.8.1.3.1.1.2 |
globalQosResetPriColorQidTidSet 1 to reset priority-color-queueId-thresholdId mapping.
Zero will be returned.rw Integer32 .1.3.6.1.4.1.52642.1.8.1.3.2 |
globalQosMapObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.1.4 |
globalQosMapIngressTableRunning table of interface ingress map. SEQUENCE OF GlobalQosMapIngressEntry .1.3.6.1.4.1.52642.1.8.1.4.1 |
globalQosMapIngressEntryEntry of globalQosMapIngressTable. GlobalQosMapIngressEntry .1.3.6.1.4.1.52642.1.8.1.4.1.1 |
globalQosMapIngressTypeType of map.
cos(1),
dscp(2),
exp(3),
ipPre(4) PriMapType .1.3.6.1.4.1.52642.1.8.1.4.1.1.1 |
globalQosMapIngressDomainIngress domain. Range is <0-7>. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.1.1.2 |
globalQosMapIngressValueDifferent type has different GlobalQosMapIngressValue.
Type-name Range of GlobalQosMapIngressValue
cos (0..7)
dscp (0..63)
ipPre (0..7)
exp (0..7) Integer32 .1.3.6.1.4.1.52642.1.8.1.4.1.1.3 |
globalQosMapIngressToPriorityInternal priority value.Range is <0-63>.rw Integer32 .1.3.6.1.4.1.52642.1.8.1.4.1.1.4 |
globalQosMapIngressToColorInternal color.Set (1)red, (2)yellow, (3)green.rw ColorType .1.3.6.1.4.1.52642.1.8.1.4.1.1.5 |
globalQosMapEgressTableRunning table of interface egress map. SEQUENCE OF GlobalQosMapEgressEntry .1.3.6.1.4.1.52642.1.8.1.4.2 |
globalQosMapEgressEntryEntry of globalQosMapEgressTable GlobalQosMapEgressEntry .1.3.6.1.4.1.52642.1.8.1.4.2.1 |
globalQosMapEgressTypeType of the egress map-table. Only value cos(1), dscp(2), exp(3) can be use. PriMapType .1.3.6.1.4.1.52642.1.8.1.4.2.1.1 |
globalQosMapEgressDomainEgress domain.Range is <0-7>. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.2.1.2 |
globalQosMapEgressPriorityInternal priority value.Range is <0-63>. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.2.1.3 |
globalQosMapEgressColorInternal color. Set (1)red, (2)yellow, (3)green. ColorType .1.3.6.1.4.1.52642.1.8.1.4.2.1.4 |
globalQosMapEgressValueDifferent type has different GlobalQosMapIngressValue.
Type-name Range of GlobalQosMapIngressValue
cos (0..7)
dscp (0..63)
exp (0..7)rw Integer32 .1.3.6.1.4.1.52642.1.8.1.4.2.1.5 |
globalQosMapPriColorQidTidTableA table of qos map priority-color to QueueId - thresholdId. SEQUENCE OF GlobalQosMapPriColorQidTidEntry .1.3.6.1.4.1.52642.1.8.1.4.3 |
globalQosMapPriColorQidTidEntryEntry of globalQosMapPriColorQidTidTable. GlobalQosMapPriColorQidTidEntry .1.3.6.1.4.1.52642.1.8.1.4.3.1 |
globalQosMapPriColorQidTidPriorityQoS Map Priority to be configured.Range is <0-63>. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.3.1.1 |
globalQosMapPriColorQidTidColorInternal color. Set (1)red, (2)yellow, (3)green. ColorType .1.3.6.1.4.1.52642.1.8.1.4.3.1.2 |
globalQosMapPriColorQidTidQueueIdThe queue id to be mapped to.Range is <0-7>.rw IfQueueId .1.3.6.1.4.1.52642.1.8.1.4.3.1.3 |
globalQosMapPriColorQidTidThresholdIdThe threasholdId id to be mapped to.Range is <0-3>.rw Integer32 .1.3.6.1.4.1.52642.1.8.1.4.3.1.4 |
globalQosMapIngressDefaultTableA table of interface ingress map. SEQUENCE OF GlobalQosMapIngressDefaultEntry .1.3.6.1.4.1.52642.1.8.1.4.4 |
globalQosMapIngressDefaultEntryEntry of globalQosMapIngressDefaultTable. GlobalQosMapIngressDefaultEntry .1.3.6.1.4.1.52642.1.8.1.4.4.1 |
globalQosMapIngressDefaultTypeType of map.
cos(1),
dscp(2),
exp(3),
ipPre(4) PriMapType .1.3.6.1.4.1.52642.1.8.1.4.4.1.1 |
globalQosMapIngressDefaultDomainIngress domain. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.4.1.2 |
globalQosMapIngressDefaultValueDifferent type has different GlobalQosMapIngressValue.
Type-name Range of GlobalQosMapIngressValue
cos (0..7)
dscp (0..63)
ipPre (0..7)
exp (0..7) Integer32 .1.3.6.1.4.1.52642.1.8.1.4.4.1.3 |
globalQosMapIngressDefaultToPriorityInternal priority value.ro Integer32 .1.3.6.1.4.1.52642.1.8.1.4.4.1.4 |
globalQosMapIngressDefaultToColorInternal color.Set (1)red, (2)yellow, (3)green.ro ColorType .1.3.6.1.4.1.52642.1.8.1.4.4.1.5 |
globalQosMapEgressDefaultTableA table of interface egress map. SEQUENCE OF GlobalQosMapEgressDefaultEntry .1.3.6.1.4.1.52642.1.8.1.4.5 |
globalQosMapEgressDefaultEntryEntry of globalQosMapEgressDefaultTable. GlobalQosMapEgressDefaultEntry .1.3.6.1.4.1.52642.1.8.1.4.5.1 |
globalQosMapEgressDefaultTypeType of the egress map-table. Only valude cos(1), dscp(2), exp(3) can be use. PriMapType .1.3.6.1.4.1.52642.1.8.1.4.5.1.1 |
globalQosMapEgressDefaultDomainEgress domain. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.5.1.2 |
globalQosMapEgressDefaultPriorityInternal priority value. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.5.1.3 |
globalQosMapEgressDefaultColorInternal color. Set (1)red, (2)yellow, (3)green. ColorType .1.3.6.1.4.1.52642.1.8.1.4.5.1.4 |
globalQosMapEgressDefaultValueDifferent type has different GlobalQosMapIngressValue.
Type-name Range of GlobalQosMapIngressValue
cos (0..7)
dscp (0..63)
exp (0..7)ro Integer32 .1.3.6.1.4.1.52642.1.8.1.4.5.1.5 |
globalQosMapPriColorQidTidDefaultTableA table of default qos mapping configuration of priority-color to QueueId - thresholdId. SEQUENCE OF GlobalQosMapPriColorQidTidDefaultEntry .1.3.6.1.4.1.52642.1.8.1.4.6 |
globalQosMapPriColorQidTidDefaultEntryEntry of globalQosMapPriColorQidTidDefaultTable. GlobalQosMapPriColorQidTidDefaultEntry .1.3.6.1.4.1.52642.1.8.1.4.6.1 |
globalQosMapPriColorQidTidDefaultPriorityInternal priority. Integer32 .1.3.6.1.4.1.52642.1.8.1.4.6.1.1 |
globalQosMapPriColorQidTidDefaultColorInternal color. Set (1)red, (2)yellow, (3)green. ColorType .1.3.6.1.4.1.52642.1.8.1.4.6.1.2 |
globalQosMapPriColorQidTidDefaultQueueIdThe queue id.ro IfQueueId .1.3.6.1.4.1.52642.1.8.1.4.6.1.3 |
globalQosMapPriColorQidTidDefaultThresholdIdThe threasholdId id.ro Integer32 .1.3.6.1.4.1.52642.1.8.1.4.6.1.4 |
globalQosCfiTableA table of qos domain cfi config. SEQUENCE OF GlobalQosCfiEntry .1.3.6.1.4.1.52642.1.8.1.5 |
globalQosCfiEntryEntry of globalQosCfiTable. GlobalQosCfiEntry .1.3.6.1.4.1.52642.1.8.1.5.1 |
globalQosCfiDomainQoS domain to be configured. Range is <0~7>. Integer32 .1.3.6.1.4.1.52642.1.8.1.5.1.1 |
globalQosCfiEnableCfi enable status of qos domain.
Set (1)enable, (2)disable.
Default:(2)disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.1.5.1.2 |
ifQos OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.2 |
ifQosShapeObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.2.1 |
ifQosShapeIfCfgTableA table of interface shape. SEQUENCE OF IfQosShapeIfCfgEntry .1.3.6.1.4.1.52642.1.8.2.1.1 |
ifQosShapeIfCfgEntryEntry of interface shape talbe. IfQosShapeIfCfgEntry .1.3.6.1.4.1.52642.1.8.2.1.1.1 |
ifQosShapeIfCfgTypePort shape mode type.
1 means port shape is based on percent of interface max bandwidth.
2 means port shape is based on the configured rate.rw Enumeration .1.3.6.1.4.1.52642.1.8.2.1.1.1.1 |
ifQosShapeIfCfgPercentPercent value of interface max bandwidth. Range is <0-99>.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.1.1.1.2 |
ifQosShapeIfCfgRateRate of interface max value. Range <0-10000000>kbps.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.1.1.1.3 |
ifQosShapeIfCfgRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.2.1.1.1.4 |
ifQosShapeQueueCfgTableA table of interface queue shape. SEQUENCE OF IfQosShapeQueueCfgEntry .1.3.6.1.4.1.52642.1.8.2.1.2 |
ifQosShapeQueueCfgEntryEntry of interface queue shape table. IfQosShapeQueueCfgEntry .1.3.6.1.4.1.52642.1.8.2.1.2.1 |
ifQosShapeQueueCfgQueueIdQueue Id of the interface. Range <0-7> IfQueueId .1.3.6.1.4.1.52642.1.8.2.1.2.1.1 |
ifQosShapeQueueCfgTypePort shape mode type.
1 means queue shape is based on percent of interface max bandwidth.
2 means queue shape is based on the configured rate.
If no shape is configured, zero will be got.rw Enumeration .1.3.6.1.4.1.52642.1.8.2.1.2.1.2 |
ifQosShapeQueueCfgPercentPercent value of interface max bandwidth. Range is <0-100>.
This value influences the commit information rate.
This value should not be larger than ifQosShapeQueueCfgPercentPeak.
If the queue shape is rate mode, this value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.1.2.1.3 |
ifQosShapeQueueCfgPercentPeakPercent value of interface max bandwidth. Range is <0-100>.
This value influences the peak information rate.
This value should not be smaller than ifQosShapeQueueCfgPercent.
If the queue shape is rate mode, this value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.1.2.1.4 |
ifQosShapeQueueCfgRateCommit information rate of interface queue shaping. Range <0-10000000>kbps.
This value should not be larger than ifQosShapeQueueCfgRatePeak.
If the queue shape is percent mode, this value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.1.2.1.5 |
ifQosShapeQueueCfgRatePeakPeak information rate of interface queue shaping. Range <0-10000000>kbps.
This value should not be smaller than ifQosShapeQueueCfgRate.
If the queue shape is percent mode, this value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.1.2.1.6 |
ifQosShapeQueueCfgRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.2.1.2.1.7 |
ifQosQueueObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.2.2 |
ifQosQueueClassDrrWeightTableA table of interface queue class and Drr Weight . SEQUENCE OF IfQosQueueClassDrrWeightEntry .1.3.6.1.4.1.52642.1.8.2.2.1 |
ifQosQueueClassDrrWeightEntryInterface queue class and Drr Weight entry. IfQosQueueClassDrrWeightEntry .1.3.6.1.4.1.52642.1.8.2.2.1.1 |
ifQosQueueClassDrrWeightQueueIdQueue Id.Range is <0-7>. IfQueueId .1.3.6.1.4.1.52642.1.8.2.2.1.1.1 |
ifQosQueueClass<0-6>:Class Id of the selected queue.
Set -1 to return it to default value.rw Integer32 (-1|0..6) .1.3.6.1.4.1.52642.1.8.2.2.1.1.2 |
ifQosQueueDrrWeightDRR weight of selected queue.
<1-100>: DRR weight range.
Set -1 to return it to default value.rw Integer32 (-1|1..100) .1.3.6.1.4.1.52642.1.8.2.2.1.1.3 |
ifQosQueueManageCfgTableA table of interface queue management. SEQUENCE OF IfQosQueueManageCfgEntry .1.3.6.1.4.1.52642.1.8.2.2.3 |
ifQosQueueManageCfgEntryEntry of ifQosQueueManageCfgTable. IfQosQueueManageCfgEntry .1.3.6.1.4.1.52642.1.8.2.2.3.1 |
ifQosQueueManageQueueIdQueue Id.Range is <0-7> IfQueueId .1.3.6.1.4.1.52642.1.8.2.2.3.1.1 |
ifQosQueueManageDropTypeQueue management mode.
(-1) taildrop.
(0-10) the value of EWMA factor,default EWMA factor is 9.
If this value is (0-10), the drop type is weighted random early drop(wred) mode.rw Integer32(-1..0) .1.3.6.1.4.1.52642.1.8.2.2.3.1.2 |
ifQosQueueManageThresholdPrecedence0Drop threshold for precedence0, only for taildrop mode.
65535 is returned for other mode.Range is <0-12884>.
The set of this value will be ignored for non-taildrop mode.
Set -1 to delete current configuration and retrieve default configuration.
For 1G port, default value is 224;
For 10G port, default value is 576rw Integer32 (-1..12884) .1.3.6.1.4.1.52642.1.8.2.2.3.1.3 |
ifQosQueueManageThresholdPrecedence1Drop threshold for precedence1, only for taildrop mode.
65535 is returned for other mode.Range is <1-12885>.
The set of this value will be ignored for non-taildrop mode.
Set -1 to delete current configuration and retrieve default configuration.
For 1G port, default value is 240;
For 10G port, default value is 592.rw Integer32 (-1|1..12885) .1.3.6.1.4.1.52642.1.8.2.2.3.1.4 |
ifQosQueueManageThresholdPrecedence2Drop threshold for precedence1, only for taildrop mode.
65535 is returned for other mode. Range is <2-12886>.
The set of this value will be ignored for non-taildrop mode.
Set -1 to delete current configuration and retrieve default configuration
for all precedence.
For 1G port, default value is 256;
For 10G port, default value is 608.rw Integer32 (-1|2..12886) .1.3.6.1.4.1.52642.1.8.2.2.3.1.5 |
ifQosQueueManageMinThresholdPre0Random-detect drop precedence0 min threshold, only for wred mode.
65535 is returned for other mode. Range is <0-12886>.
The set of this value will be ignored for non-wred mode.
Set -1 to delete current configuration and retrieve default configuration
for all precedence.
For 1G port, default value is 16;rw Integer32 (-1|0..12886) .1.3.6.1.4.1.52642.1.8.2.2.3.1.6 |
ifQosQueueManageMinThresholdPre1Random-detect drop precedence1 min threshold, only for wred mode.
65535 is returned for other mode. Range is <0-12886>.
The set of this value will be ignored for non-wred mode.
Set -1 to delete current configuration and retrieve default configuration
for all precedence.
For 1G port, default value is 24;rw Integer32 (-1|0..12886) .1.3.6.1.4.1.52642.1.8.2.2.3.1.7 |
ifQosQueueManageMinThresholdPre2Random-detect drop precedence2 min threshold, only for wred mode.
65535 is returned for other mode. Range is <0-12886>.For 1G port, default value is 32;
Set -1 to delete current configuration and retrieve default configuration.rw Integer32 (-1|0..12886) .1.3.6.1.4.1.52642.1.8.2.2.3.1.8 |
ifQosQueueManageMaxThresholdPre0Random-detect drop precedence0 max threshold, only for wred mode,
65535 is returned for other mode.Range is <1-12887>.
The set of this value will be ignored for non-wred mode.
Set -1 to delete current configuration and retrieve default configuration
for all precedence.
For 1G port, default value is 480;rw Integer32 (-1|1..12887) .1.3.6.1.4.1.52642.1.8.2.2.3.1.9 |
ifQosQueueManageMaxThresholdPre1Random-detect drop precedence1 max threshold, only for wred mode.
The set of this value will be ignored for non-wred mode.
65535 is returned for other mode. Range is <1-12887>.
Set -1 to delete current configuration and retrieve default configuration
for all precedence.
For 1G port, default value is 496;rw Integer32 (-1|1..12887) .1.3.6.1.4.1.52642.1.8.2.2.3.1.10 |
ifQosQueueManageMaxThresholdPre2Random-detect drop precedence2 max threshold, only for wred mode.
The set of this value will be ignored for non-taildrop mode.
65535 is returned for other mode. Range is <1-12887>.
Set -1 to delete current configuration and retrieve default configuration
for all precedence.
For 1G port, default value is 512;rw Integer32 (-1|1..12887) .1.3.6.1.4.1.52642.1.8.2.2.3.1.11 |
ifQosQueueManageDropProbabilityPre0Random-detect drop precedence0 drop probability, only for wred mode.
Set -1 to delete current configuration and retrieve default configuration.
The default value is 1024. -2 is returned for other mode. Range is <0-65535>.rw Integer32 (-1|0..65535) .1.3.6.1.4.1.52642.1.8.2.2.3.1.12 |
ifQosQueueManageDropProbabilityPre1Random-detect drop precedence1 drop probability, only for wred mode.
Set -1 to delete current configuration and retrieve default configuration.
The default value is 1024. -2 is returned for other mode. Range is <0-65535>.rw Integer32 (-1|0..65535) .1.3.6.1.4.1.52642.1.8.2.2.3.1.13 |
ifQosQueueManageDropProbabilityPre2Random-detect drop precedence2 drop probability, only for wred mode.
Set -1 to delete current configuration and retrieve default configuration.
The default value is 1024. -2 is returned for other mode. Range is <0-65535>.rw Integer32 (-1|0..65535) .1.3.6.1.4.1.52642.1.8.2.2.3.1.14 |
ifQosCarObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.2.3 |
ifQosCarApplyTableA table of interface CAR applied. SEQUENCE OF IfQosCarApplyEntry .1.3.6.1.4.1.52642.1.8.2.3.1 |
ifQosCarApplyEntryEntry of ifQosCarApplyTable. IfQosCarApplyEntry .1.3.6.1.4.1.52642.1.8.2.3.1.1 |
ifQosCarApplyDirectionDirection of this port-policer applied on.
(1) input.
(2) output. Enumeration .1.3.6.1.4.1.52642.1.8.2.3.1.1.1 |
ifQosCarApplyColorModeValue 1 for color aware mode policer,
value 2 for color blind mode policer.rw Enumeration .1.3.6.1.4.1.52642.1.8.2.3.1.1.2 |
ifQosCarApplyCirCommit information rate (kbps).
Range is <8-10000000>.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.3.1.1.3 |
ifQosCarApplyCbsCommit burst size (bytes).
Range is <1000-128000>.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.3.1.1.4 |
ifQosCarApplyTypeSet (1) is select rfc2697 mode.
Set (2) is select rfc2698 mode.
Set (3) is select rfc4115 mode.
Set (4) is select bwp mode.rw Enumeration .1.3.6.1.4.1.52642.1.8.2.3.1.1.5 |
ifQosCarApplyPirWhen Type mode is rcf2698 means Peak information rate (kbps).
When Type mode is rfc2697&rfc4115&bwp means Excess Information Rate (kbps).
Range is <8-10000000>.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.3.1.1.7 |
ifQosCarApplyPbsWhen Type mode is rcf2698 means Peak burst size (bytes).
When Type mode is rfc2697&rfc4115&bwp means Excess Burst Size (bytes).
Range is <1000-128000>.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.3.1.1.8 |
ifQosCarApplyDropColorDrop color configuration.When configuring 'red(1)',
it only drops red packet; configuring 'yellow(2)',
it drops both 'red' and 'yellow' packet.rw Enumeration .1.3.6.1.4.1.52642.1.8.2.3.1.1.9 |
ifQosCarApplyUseL3Length2 for using L2 frame length;
1 for using L3 length.rw Enumeration .1.3.6.1.4.1.52642.1.8.2.3.1.1.10 |
ifQosCarApplyRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.2.3.1.1.11 |
ifQosPriObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.2.4 |
ifQosCosTableA table of interface cos value. SEQUENCE OF IfQosCosEntry .1.3.6.1.4.1.52642.1.8.2.4.1 |
ifQosCosEntryEntry of ifQosCosTable. IfQosCosEntry .1.3.6.1.4.1.52642.1.8.2.4.1.1 |
ifQosCosValueCos value for this interface.Range is <0-7>.
The default CoS for each interface is 0.rw Integer32 .1.3.6.1.4.1.52642.1.8.2.4.1.1.1 |
ifQosTrustTypeTableA table of interface trust type. SEQUENCE OF IfQosTrustTypeEntry .1.3.6.1.4.1.52642.1.8.2.4.2 |
ifQosTrustTypeEntryEntry of ifQosTrustTypeTable. IfQosTrustTypeEntry .1.3.6.1.4.1.52642.1.8.2.4.2.1 |
ifQosTrustTypeValueTrust priority type for this interface.
Set trust-default to delete current configuration and retrieve default configuration.
trustDefault(-1)
trustPort(0)
trustSTagCos(2)
trustDscpExp(3)
trustIpPre(4)
trustCTagCos(5)rw Enumeration .1.3.6.1.4.1.52642.1.8.2.4.2.1.1 |
ifQosDomainTableA table of interface Domain value. SEQUENCE OF IfQosDomainEntry .1.3.6.1.4.1.52642.1.8.2.4.3 |
ifQosDomainEntryEntry of ifQosDomainTable. IfQosDomainEntry .1.3.6.1.4.1.52642.1.8.2.4.3.1 |
ifQosDomainValueDomain value for this interface.
Range <0-7>. The default value is
0rw Integer32 .1.3.6.1.4.1.52642.1.8.2.4.3.1.1 |
ifQosReplacePriObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.2.5 |
ifQosReplaceTableA table of ifQosReplaceEntry. SEQUENCE OF IfQosReplaceEntry .1.3.6.1.4.1.52642.1.8.2.5.1 |
ifQosReplaceEntryEntry of ifQosReplaceTable. IfQosReplaceEntry .1.3.6.1.4.1.52642.1.8.2.5.1.1 |
ifQosReplaceTypeReplace priority type for this interface. The defult cos is stagcos;
The value of set this node only can be follow:
cos(1),
cosctag(2),
cosstag(3),
dscpExp(4),
nodscp(7),
nocos(8)rw Enumeration .1.3.6.1.4.1.52642.1.8.2.5.1.1.1 |
cbQoS OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.3 |
cbQoSClassifierObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.3.1 |
cbQoSClassifierIndexNextThis object contains an appropriate value to be used for
cbQoSClassifierIndex when creating rows in the
cbQoSClassifierCfgInfoTable.
If the value of this node is less than 0,
it indicates creating a Rowin cbQoSClassifierCfgInfoTable is not permitted.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.1.1 |
cbQoSClassifierCfgInfoTableA table of Classifier configuration information. SEQUENCE OF CBQoSClassifierCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.1.2 |
cbQoSClassifierCfgInfoEntryClassifier Configuration Information Entry. CBQoSClassifierCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.1.2.1 |
cbQoSClassifierIndexIndex of this class-map.Range is <10000-20000>. Integer32 .1.3.6.1.4.1.52642.1.8.3.1.2.1.1 |
cbQoSClassifierNameName of class-map. Only used in creating a conceptual row,
can not modified in an 'active' Rowrw OCTET STRING .1.3.6.1.4.1.52642.1.8.3.1.2.1.2 |
cbQoSClassifierRuleCountThe counter of match rules in class-map.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.1.2.1.3 |
cbQoSClassifierOperatorOperator of the match rules of class-map. Default match operator is match-any.
'and(1)' for match-all rules. 'or(2)' for match-any rules.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.1.2.1.4 |
cbQoSClassifierMatchRuleNextIndexThis object contains an appropriate value to be used for
cbQoSMatchRuleIndex when creating rows in the
cbQoSMatchRuleCfgInfoTable.Begin with 0.
If the value of this node is less than 0,
it indicates creating a Rowin cbQoSMatchRuleCfgInfoTable is not permitted.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.1.2.1.5 |
cbQoSClassifierRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.1.2.1.6 |
cbQoSMatchRuleCfgInfoTableA table of match rule configuration in class-map. SEQUENCE OF CBQoSMatchRuleCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.1.3 |
cbQoSMatchRuleCfgInfoEntryMatch Rule Entry in Class-map. CBQoSMatchRuleCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.1.3.1 |
cbQoSMatchRuleIndexIndex of Match Rule. Currently only access-group(ACL) is used as matching rule.
Range is <10000-20000>. Integer32 .1.3.6.1.4.1.52642.1.8.3.1.3.1.1 |
cbQoSMatchRuleACLNameMatch ACl name.Only used in creating a conceptual row,
can not modified in an 'active' Rowrw OCTET STRING .1.3.6.1.4.1.52642.1.8.3.1.3.1.2 |
cbQoSMatchRuleRowStatusThe status of this conceptual row.Now only realize CreateAndGo and
Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.1.3.1.3 |
cbQoSPolicyObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.3.2 |
cbQoSPolicyIndexNextThis object contains an appropriate value to be used for
cbQoSPolicyIndex when creating rows in the
cbQoSPolicyCfgInfoTable.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.2.1 |
cbQoSPolicyCfgInfoTableA table of policy-map. SEQUENCE OF CBQoSPolicyCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.2.2 |
cbQoSPolicyCfgInfoEntryPolicy-map table Entry. CBQoSPolicyCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.2.2.1 |
cbQoSPolicyIndexIndex of this policy-map.Range is <10000-20000>. Integer32 .1.3.6.1.4.1.52642.1.8.3.2.2.1.1 |
cbQoSPolicyNameName of this policy-map. Only used in creating a conceptual row,
can not modified in an 'active' Rowrw OCTET STRING .1.3.6.1.4.1.52642.1.8.3.2.2.1.2 |
cbQoSPolicyClassCountThe counter of class-maps in this policy-map.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.2.2.1.3 |
cbQoSPolicyClassNextIndexThis object contains an appropriate value to be used for
cbQoSPolicyClassIndex when creating rows in the
cbQoSPolicyClassCfgInfoTable.
If the returned value is less 0,
it indicates creating a Rowis not permitted.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.2.2.1.4 |
cbQoSPolicyRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.2.2.1.5 |
cbQoSPolicyClassCfgInfoTableA table of policy-class. SEQUENCE OF CBQoSPolicyClassCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.2.3 |
cbQoSPolicyClassCfgInfoEntryPolicy-class table Entry. CBQoSPolicyClassCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.2.3.1 |
cbQoSPolicyClassIndexIndex of this policy-class.Range is <10000-20000>. Integer32 .1.3.6.1.4.1.52642.1.8.3.2.3.1.1 |
cbQoSPolicyClassClassifierIndexIndex of classifier applied by a policy.
It is corresponding to cbQoSClassifierName.
The maximum index value 20000 is reserved for class-map class-default only. Integer32 .1.3.6.1.4.1.52642.1.8.3.2.3.1.2 |
cbQoSPolicyClassClassifierNameName of classifier applied by a policy.
It should exist in cbQoSClassifierCfgInfoTable.
Only used in creating a conceptual row, can not modified in an 'active' row.rw OCTET STRING .1.3.6.1.4.1.52642.1.8.3.2.3.1.3 |
cbQoSPolicyClassRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.2.3.1.4 |
cbQoSBehaviorObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.3.3 |
cbQoSAggregativeCarIndexNextThis object contains an appropriate value to be used for
cbQoSAggregativeCarIndex when creating rows in the
cbQoSAggregativeCarCfgInfoTable.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.3.1 |
cbQoSAggregativeCarCfgInfoTableA table of aggregate-policer. SEQUENCE OF CBQoSAggregativeCarCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.3.2 |
cbQoSAggregativeCarCfgInfoEntryAggregate-policer table Entry. CBQoSAggregativeCarCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.3.2.1 |
cbQoSAggregativeCarIndexIndex of aggregate-policer.Range is <10000-20000>. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.2.1.1 |
cbQoSAggregativeCarNameName of aggregate-policer.Only used in creating a conceptual row,
can not modified in an 'active' row.rw OCTET STRING .1.3.6.1.4.1.52642.1.8.3.3.2.1.2 |
cbQoSAggregativeCarColorModeValue 1 for color aware mode policer;
value 2 for color blind mode policer.
Can modified in an 'active' row.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.2.1.3 |
cbQoSAggregativeCarCirCommit information rate (kbps).Range is <8-10000000>.
Only used in creating a conceptual row,
can not modified in an 'active' row.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.2.1.4 |
cbQoSAggregativeCarCbsCommit burst size (bytes).Range is <1000-128000>.
Only used in creating a conceptual row,
can not modified in an 'active' row.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.2.1.5 |
cbQoSAggregativeCarTypeSet (1) is select TRTCM mode.
Set (2) is select SRTCM mode.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.2.1.6 |
cbQoSAggregativeCarEbsExcess burst size (bytes).Range is <1000-128000>.
Only used in creating a conceptual row,
can not modified in an 'active' row.
If the cbQoSAggregativeCarPir is not zero,
this value will be ignored.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.2.1.7 |
cbQoSAggregativeCarPirPeak information rate (kbps).Range is <8-10000000>.
Only used in creating a conceptual row,
can not modified in an 'active' row.
This valude should not be less than cbQoSAggregativeCarCir.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.2.1.8 |
cbQoSAggregativeCarPbsPeak burst size (bytes).Range is <1000-128000>.
Only used in creating a conceptual row,
can not modified in an 'active' row.
If the cbQoSAggregativeCarPir is zero,
this value will be ignored;
This valude should not be less than cbQoSAggregativeCarCbs.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.2.1.9 |
cbQoSAggregativeCarDropColorDrop color configuration.When configuring 'red',
it only drops red packet; configuring 'yellow',
it drops both 'red' and 'yellow' packet.
Only used in creating a conceptual row,
can not modified in an 'active' row.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.2.1.10 |
cbQoSAggregativeCarUseL3Length2 for using L2 frame length;
1 for using L3 length.
Only used in creating a conceptual row,
can not modified in an 'active' row.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.2.1.11 |
cbQoSAggregativeCarStats2 policer stats is disable;
1 policer stats is enable.
Only used in creating a conceptual row,
can not modified in an 'active' row.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.2.1.12 |
cbQoSAggregativeCarRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.3.2.1.13 |
cbQoSBehaviorCarCfgInfoTableA table of behavior. SEQUENCE OF CbQoSBehaviorCarCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.3.3 |
cbQoSBehaviorCarCfgInfoEntryBehavior table Entry. CbQoSBehaviorCarCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.3.3.1 |
cbQoSBehaviorCarPolicyIndexIndex of Policy-map. Range is <10000-20000>.
Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.3.1.1 |
cbQoSBehaviorCarPolicyClassIndexIndex of Policy class-map. Range is <10000-20000>.
Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.3.1.2 |
cbQoSBehaviorCarColorModeValue 1 for color aware mode policer,
value 2 for color blind mode policer.
Only for policer behavior.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.3.1.5 |
cbQoSBehaviorCarCirCommit information rate (kbps).Range is <8-10000000>.
Only for policer behavior.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.3.1.6 |
cbQoSBehaviorCarCbsCommit burst size (bytes).Range is <1000-128000>.
Only for policer behavior.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.3.1.7 |
cbQoSBehaviorCarTypeSet (1) is select rfc2697 mode.
Set (2) is select rfc2698 mode.
Set (3) is select rfc4115 mode.
Set (4) is select bwp mode.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.3.1.8 |
cbQoSBehaviorCarEbsExcess burst size (bytes).Range is <1000-128000>.
Only for policer behavior.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.3.1.9 |
cbQoSBehaviorCarPirPeak information rate (kbps).Range is <8-10000000>.
Only for policer behavior.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.3.1.10 |
cbQoSBehaviorCarPbsPeak burst size (bytes).Range is <1000-128000>.
Only for policer behavior.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.3.1.11 |
cbQoSBehaviorCarDropColorDrop color configuration.Only 'red' and 'yellow' can be used here.
When configuring 'red(1)', it only drops red packet;
configuring 'yellow(2)', it drops both 'red' and 'yellow' packet.
Only for policer behavior.
When policy mode is aggregative policer, the result of DropColor will be none(0).rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.3.1.12 |
cbQoSBehaviorCarUseL3Length2 for using L2 frame length;
1 for using L3 length.
Only for policer behavior.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.3.1.13 |
cbQoSBehaviorCarStats2 policer stats is disable;
1 policer stats is enable.
Only for policer behavior.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.3.1.14 |
cbQoSBehaviorCarRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.3.3.1.15 |
cbQoSBehaviorPriColorCfgInfoTableA table of setting priority-color behavior. SEQUENCE OF CbQoSBehaviorPriColorCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.3.4 |
cbQoSBehaviorPriColorCfgInfoEntrySetting priority-color table Entry. CbQoSBehaviorPriColorCfgInfoEntry .1.3.6.1.4.1.52642.1.8.3.3.4.1 |
cbQoSBehaviorPriColorPolicyIndexIndex of Policy-map. Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.4.1.1 |
cbQoSBehaviorPriColorPolicyClassIndexIndex of Policy class-map.Range is <10000-20000>.
Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.4.1.2 |
cbQoSBehaviorPriColorSetPriorityInternal priority value.Range id <0-63>.
Default priority is 0.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.4.1.3 |
cbQoSBehaviorPriColorSetColorInternal color. Set (1)red, (2)yellow, (3)green.
Set (0) means no set priority.rw ColorType .1.3.6.1.4.1.52642.1.8.3.3.4.1.4 |
cbQoSBehaviorOptionTableA table of behavior. SEQUENCE OF CbQoSBehaviorOptionEntry .1.3.6.1.4.1.52642.1.8.3.3.5 |
cbQoSBehaviorOptionEntryClassTrafficOption table Entry. CbQoSBehaviorOptionEntry .1.3.6.1.4.1.52642.1.8.3.3.5.1 |
cbQoSBehaviorOptionPolicyIndexIndex of Policy-map.Range is <10000-20000>.
Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.5.1.1 |
cbQoSBehaviorOptionPolicyClassIndexIndex of Policy class-map.Range is <10000-20000>.
Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.5.1.2 |
cbQoSBehaviorOptionTrustUse which prioritization type for this flow.
trustNone(-1)
trustPort(0)
trustCos(2)
trustDscp(3)
trustIpPre(4)
trustCosCtag(5)
trustCosStag(6)rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.5.1.3 |
cbQoSBehaviorOptionStatsEn1 for enable statistics for each ace in class map;
2 for disable statistics for each ace in class map.
Default value is 2.rw Enumeration .1.3.6.1.4.1.52642.1.8.3.3.5.1.4 |
cbQoSBehaviorOptionRedirectIfindex<1-65535>:Interface index of redirect.
Set 0 means no redirect.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.5.1.5 |
cbQoSBehaviorOptionMonitorSession<1-3> monitor session number;
0 no monitor, default value is 0.rw Integer32 .1.3.6.1.4.1.52642.1.8.3.3.5.1.6 |
cbQoSBehaviorCarAgpCfgTableA table of behavior. SEQUENCE OF CbQoSBehaviorCarAgpCfgEntry .1.3.6.1.4.1.52642.1.8.3.3.6 |
cbQoSBehaviorCarAgpCfgEntryBehavior table Entry. CbQoSBehaviorCarAgpCfgEntry .1.3.6.1.4.1.52642.1.8.3.3.6.1 |
cbQoSBehaviorCarAgpPolicyIndexIndex of Policy-map. Range is <10000-20000>.
Associated with cbQoSPolicyIndex of cbQoSPolicyCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.6.1.1 |
cbQoSBehaviorCarAgpPolicyClassIndexIndex of Policy class-map. Range is <10000-20000>.
Associated with cbQoSPolicyClassIndex of cbQoSPolicyClassCfgInfoEntry. Integer32 .1.3.6.1.4.1.52642.1.8.3.3.6.1.2 |
cbQoSBehaviorCarAgpCarNameOnly for aggregative policer name.rw OCTET STRING .1.3.6.1.4.1.52642.1.8.3.3.6.1.3 |
cbQoSBehaviorCarAgpRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.3.6.1.15 |
cbQoSApplyPolicyObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.3.4 |
cbQoSIfApplyPolicyTableA table of policy applied on interface. SEQUENCE OF CBQoSIfApplyPolicyEntry .1.3.6.1.4.1.52642.1.8.3.4.1 |
cbQoSIfApplyPolicyEntryPolicy-applied table Entry. CBQoSIfApplyPolicyEntry .1.3.6.1.4.1.52642.1.8.3.4.1.1 |
cbQoSIfApplyPolicyIfIndexIfindex. The interface should only be physical, vlan, or linkagg interface. Integer32 .1.3.6.1.4.1.52642.1.8.3.4.1.1.1 |
cbQoSIfApplyPolicyDirectionDirection of this service-policy applied on.
1. input direction.
2. output direction. Enumeration .1.3.6.1.4.1.52642.1.8.3.4.1.1.2 |
cbQoSIfApplyPolicyIndexIndex of policy in cbQoSPolicyCfgInfoTable.
It is corresponding to cbQoSIfApplyPolicyName.ro Integer32 .1.3.6.1.4.1.52642.1.8.3.4.1.1.3 |
cbQoSIfApplyPolicyNameName of policy applied.
It should exist in cbQoSPolicyCfgInfoTable.
Only used in creating a conceptual row, can not modified in an 'active' Rowrw OCTET STRING .1.3.6.1.4.1.52642.1.8.3.4.1.1.4 |
cbQoSIfApplyPolicyRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.3.4.1.1.5 |
srvQos OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.4 |
srvQosSapIngressObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.4.1 |
srvQosSapIngressTableTable of qos sap ingress. SEQUENCE OF SrvQosSapIngressEntry .1.3.6.1.4.1.52642.1.8.4.1.1 |
srvQosSapIngressEntryEntries of qos sap ingress. SrvQosSapIngressEntry .1.3.6.1.4.1.52642.1.8.4.1.1.1 |
srvQosSapIngressNameName of the qos sap ingress. OCTET STRING .1.3.6.1.4.1.52642.1.8.4.1.1.1.1 |
srvQosSapIngressRowStatusStatus of the srvQosSapIngressEntry row.
1 means Active
4 means CreateAndGo
6 means Destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.4.1.1.1.2 |
srvQosSapIngressDescriptionDescrption of the qos sap ingress.rw OCTET STRING .1.3.6.1.4.1.52642.1.8.4.1.1.1.3 |
srvQosSapIngressApplyPolicyMapPolicy map for the qos sap ingress.rw OCTET STRING .1.3.6.1.4.1.52642.1.8.4.1.1.1.4 |
srvQosSapIngressPolicerTableTable of qos sap ingress policer. SEQUENCE OF SrvQosSapIngressPolicerEntry .1.3.6.1.4.1.52642.1.8.4.1.2 |
srvQosSapIngressPolicerEntryEntries of qos sap ingress policer. SrvQosSapIngressPolicerEntry .1.3.6.1.4.1.52642.1.8.4.1.2.1 |
srvQosSapIngressPolicerModePolicer mode of the qos sap ingress.rw Enumeration .1.3.6.1.4.1.52642.1.8.4.1.2.1.1 |
srvQosSapIngressPolicerCirCir of the qos sap ingress.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.1.2.1.2 |
srvQosSapIngressPolicerCbsCbs of the qos sap ingress.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.1.2.1.3 |
srvQosSapIngressPolicerEbsEbs of the qos sap ingress.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.1.2.1.4 |
srvQosSapIngressPolicerPirPir of the qos sap ingress.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.1.2.1.5 |
srvQosSapIngressPolicerPbsPbs of the qos sap ingress.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.1.2.1.6 |
srvQosSapIngressPolicerDropColorDrop color of the qos sap ingress.rw Enumeration .1.3.6.1.4.1.52642.1.8.4.1.2.1.7 |
srvQosSapIngressPolicerUseL3LengthIf L3 length is used for the qos sap ingress.rw Enumeration .1.3.6.1.4.1.52642.1.8.4.1.2.1.8 |
srvQosSapEgressObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.4.2 |
srvQosSapEgressTableTable of qos sap Egress. SEQUENCE OF SrvQosSapEgressEntry .1.3.6.1.4.1.52642.1.8.4.2.1 |
srvQosSapEgressEntryEntries of qos sap Egress. SrvQosSapEgressEntry .1.3.6.1.4.1.52642.1.8.4.2.1.1 |
srvQosSapEgressNameName of the qos sap Egress. OCTET STRING .1.3.6.1.4.1.52642.1.8.4.2.1.1.1 |
srvQosSapEgressRowStatusStatus of the srvQosSapEgressEntry row.
1 means Active
4 means CreateAndGo
6 means Destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.8.4.2.1.1.2 |
srvQosSapEgressDescriptionDescrption of the qos sap Egress.rw OCTET STRING .1.3.6.1.4.1.52642.1.8.4.2.1.1.3 |
srvQosSapEgressShapeAverageTotal Rate of the qos sap Egress.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.1.1.4 |
srvQosSapEgressQueueTableTable of qos sap egress queue. SEQUENCE OF SrvQosSapEgressQueueEntry .1.3.6.1.4.1.52642.1.8.4.2.2 |
srvQosSapEgressQueueEntryEntries of qos sap egress queue. SrvQosSapEgressQueueEntry .1.3.6.1.4.1.52642.1.8.4.2.2.1 |
srvQosSapEgressQueueIdId of the qos sap Egress Queue. Integer32 .1.3.6.1.4.1.52642.1.8.4.2.2.1.1 |
srvQosSapEgressQueueShapeAverageRateCirShape rate for commit information rate, kbps.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.2.1.2 |
srvQosSapEgressQueueShapeAverageRatePirShape rate for peak information rate, kbps.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.2.1.3 |
srvQosSapEgressQueueInfoTableTable of qos sap egress queue info. SEQUENCE OF SrvQosSapEgressQueueInfoEntry .1.3.6.1.4.1.52642.1.8.4.2.3 |
srvQosSapEgressQueueInfoEntryEntries of qos sap egress queue info. SrvQosSapEgressQueueInfoEntry .1.3.6.1.4.1.52642.1.8.4.2.3.1 |
srvQosSapEgressQueueInfoRandomDetect-1: Tail Drop
0-10: WRED Exponential-Weighted-Moving-Average (EWMA) factor.rw Integer32 (-1..10) .1.3.6.1.4.1.52642.1.8.4.2.3.1.1 |
srvQosSapEgressQueueInfoTailDropThreshold0Tail drop threshold0.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.2 |
srvQosSapEgressQueueInfoTailDropThreshold1Tail drop threshold1, should greater than threshold0.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.3 |
srvQosSapEgressQueueInfoTailDropThreshold2Tail drop threshold2, should greater than threshold1.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.4 |
srvQosSapEgressQueueInfoTailDropThreshold3Tail drop threshold3, should greater than threshold2.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.5 |
srvQosSapEgressQueueInfoRandomDetectMinThreshold0Random-detect threshold0's min threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.6 |
srvQosSapEgressQueueInfoRandomDetectMinThreshold1Random-detect threshold1's min threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.7 |
srvQosSapEgressQueueInfoRandomDetectMinThreshold2Random-detect threshold2's min threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.8 |
srvQosSapEgressQueueInfoRandomDetectMinThreshold3Random-detect threshold3's min threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.9 |
srvQosSapEgressQueueInfoRandomDetectMaxThreshold0Random-detect threshold0's max threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.10 |
srvQosSapEgressQueueInfoRandomDetectMaxThreshold1Random-detect threshold1's max threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.11 |
srvQosSapEgressQueueInfoRandomDetectMaxThreshold2Random-detect threshold2's max threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.12 |
srvQosSapEgressQueueInfoRandomDetectMaxThreshold3Random-detect threshold3's max threshold range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.13 |
srvQosSapEgressQueueInfoRandomDetectDropProbability0Random-detect threshold0 drop probability range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.14 |
srvQosSapEgressQueueInfoRandomDetectDropProbability1Random-detect threshold1 drop probability range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.15 |
srvQosSapEgressQueueInfoRandomDetectDropProbability2Random-detect threshold2 drop probability range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.16 |
srvQosSapEgressQueueInfoRandomDetectDropProbability3Random-detect threshold3 drop probability range.rw Integer32 .1.3.6.1.4.1.52642.1.8.4.2.3.1.17 |
srvQosFreeQueueInfoObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.4.3 |
srvQosFreeQueueInfoServiceQueueNumNumber of queues allocated by each service.ro Integer32 .1.3.6.1.4.1.52642.1.8.4.3.1 |
srvQosFreeQueueInfoMaxSupportQueueNumThe maximum support queue number.ro Integer32 .1.3.6.1.4.1.52642.1.8.4.3.2 |
srvQosFreeQueueInfoAllocatedQueueNumThe allocated queue number.ro Integer32 .1.3.6.1.4.1.52642.1.8.4.3.3 |
srvQosFreeQueueInfoMaxSupportServiceNumThe maximum support service number.ro Integer32 .1.3.6.1.4.1.52642.1.8.4.3.4 |
srvQosFreeQueueInfoAllocatedServiceNumThe allocated service number.ro Integer32 .1.3.6.1.4.1.52642.1.8.4.3.5 |
stats OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.10 |
qosStatsEnableObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.10.1 |
qosStatsPolicyEnableThe status of policer statistics.
(1) enable.
(2) disable.rw EnableType .1.3.6.1.4.1.52642.1.8.10.1.1 |
qosStatsQueueEnableThe status of queue statistics.
(1) enable.
(2) disable.rw EnableType .1.3.6.1.4.1.52642.1.8.10.1.2 |
qosStatsClearStaticsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.10.2 |
qosStatsClearPolicyTableA table of clearing Stats for Policy in a QoS policy applied on the interface. SEQUENCE OF QosStatsClearPolicyEntry .1.3.6.1.4.1.52642.1.8.10.2.1 |
qosStatsClearPolicyEntryClear Stats information entry. QosStatsClearPolicyEntry .1.3.6.1.4.1.52642.1.8.10.2.1.1 |
qosStatsClearPolicyIndexPolicy map entry index. Range 10000~20000. Integer32 .1.3.6.1.4.1.52642.1.8.10.2.1.1.1 |
qosStatsClearPolicyPolicerStatsReset the value of the policer statistics in policy-map.Clear(0).rw QosStatsClear .1.3.6.1.4.1.52642.1.8.10.2.1.1.2 |
qosStatsClearPolicyAceMatchStatsReset the value of the ace-matching statistics in policy-map.Clear(0).rw QosStatsClear .1.3.6.1.4.1.52642.1.8.10.2.1.1.3 |
qosStatsClearPortPolicyTableA table of clearing Stats for Policy
in a QoS PortPolicy applied on the interface. SEQUENCE OF QosStatsClearPortPolicyEntry .1.3.6.1.4.1.52642.1.8.10.2.2 |
qosStatsClearPortPolicyEntryClear Stats information entry. QosStatsClearPortPolicyEntry .1.3.6.1.4.1.52642.1.8.10.2.2.1 |
qosStatsClearPortPolicyIfIndexInterface Index, equal to ifIndex. Integer32 .1.3.6.1.4.1.52642.1.8.10.2.2.1.1 |
qosStatsClearPortPolicyDirectionPolicy direction:
inbound (1)
outbound (2) DirectionType .1.3.6.1.4.1.52642.1.8.10.2.2.1.2 |
qosStatsClearPortPolicyStatsReset the statistics of port policer.Clear(0).rw QosStatsClear .1.3.6.1.4.1.52642.1.8.10.2.2.1.3 |
qosStatsClearAggPolicyTableA table of clearing Stats for Policy in a QoS AggPolicy applied on the
interface. SEQUENCE OF QosStatsClearAggPolicyEntry .1.3.6.1.4.1.52642.1.8.10.2.3 |
qosStatsClearAggPolicyEntryClear agg policer stats information entry. QosStatsClearAggPolicyEntry .1.3.6.1.4.1.52642.1.8.10.2.3.1 |
qosStatsClearAggPolicyIndexIndex of aggregate-policer. Integer32 .1.3.6.1.4.1.52642.1.8.10.2.3.1.1 |
qosStatsClearAggPolicyStatsReset the value of the Stats.Clear(0).rw QosStatsClear .1.3.6.1.4.1.52642.1.8.10.2.3.1.2 |
qosStatsClearQueueTableA table of clearing Stats for Policy in a QoS Queue applied on the
interface. SEQUENCE OF QosStatsClearQueueEntry .1.3.6.1.4.1.52642.1.8.10.2.4 |
qosStatsClearQueueEntryClear Stats information entry. QosStatsClearQueueEntry .1.3.6.1.4.1.52642.1.8.10.2.4.1 |
qosStatsClearQueueifIndexInterface Index, equal to ifIndex. Integer32 .1.3.6.1.4.1.52642.1.8.10.2.4.1.1 |
qosStatsClearQueueIdInterface queue id. IfQueueId .1.3.6.1.4.1.52642.1.8.10.2.4.1.2 |
qosStatsClearQueueStatsReset the value of the Stats.Clear(0).rw QosStatsClear .1.3.6.1.4.1.52642.1.8.10.2.4.1.3 |
qosStatsRunStaticsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.8.10.3 |
qosStatsCbPolicyRunInfoTableA table of Running Stats for Policy in a QoS policy applied on the interface. SEQUENCE OF QosStatsCbPolicyRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.1 |
qosStatsCbPolicyRunInfoEntryPolicy Stats information entry. QosStatsCbPolicyRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.1.1 |
qosStatsCbPolicyIfIndexInterface Index, equal to ifIndex. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.1.1.1 |
qosStatsCbPolicyDirectionPolicy direction:
inbound (1)
outbound (2) DirectionType .1.3.6.1.4.1.52642.1.8.10.3.1.1.2 |
qosStatsPolicyClassIndexPolicyClass Index in a QoS policy. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.1.1.3 |
qosStatsPolicyGreenPacketsNumber of green packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.4 |
qosStatsPolicyGreenBytesNumber of green bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.5 |
qosStatsPolicyRedPacketsNumber of red packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.6 |
qosStatsPolicyRedBytesNumber of red bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.7 |
qosStatsPolicyYellowPacketsNumber of yellow packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.8 |
qosStatsPolicyYellowBytesNumber of yellow bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.9 |
qosStatsPolicyClassBasedPktsNumber of policy class matching packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.10 |
qosStatsPolicyClassBasedBytesNumber of policy class matching bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.1.1.11 |
qosStatsPortPolicyRunInfoTableA table of Running Stats in a QoS policy applied on the port. SEQUENCE OF QosStatsPortPolicyRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.2 |
qosStatsPortPolicyRunInfoEntryPolicy Stats information entry. QosStatsPortPolicyRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.2.1 |
qosStatsPortPolicyIfIndexInterface Index, equal to ifIndex. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.2.1.1 |
qosStatsPortPolicyDirectionPolicy direction:
inbound (1)
outbound (2) DirectionType .1.3.6.1.4.1.52642.1.8.10.3.2.1.2 |
qosStatsPortPolicyConfirmPacketsNumber of green packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.2.1.3 |
qosStatsPortPolicyConfirmBytesNumber of green bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.2.1.4 |
qosStatsPortPolicyNoConfirmPacketsNumber of red packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.2.1.5 |
qosStatsPortPolicyNoConfirmBytesNumber of red bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.2.1.6 |
qosStatsIfQueueRunInfoTableA table of Running Stats for queue
in a QoS policy applied on the interface. SEQUENCE OF QosStatsIfQueueRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.3 |
qosStatsIfQueueRunInfoEntryQueue Stats entry. QosStatsIfQueueRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.3.1 |
qosStatsQueueIfIndexInterface Index, equal to ifIndex. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.3.1.1 |
qosStatsQueueIDQueue ID. Range <0-7>. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.3.1.2 |
qosStatsIfQueueTransmittedPacketsNumber of packets enqueued.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.3.1.3 |
qosStatsIfQueueTransmittedBytesNumber of bytes enqueued.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.3.1.4 |
qosStatsIfQueueDropPacketsNumber of packets discarded when enqueued by tail-drop/wred method. It's zero if the system does not support queue drop statistics.roobsolete Counter64 .1.3.6.1.4.1.52642.1.8.10.3.3.1.5 |
qosStatsIfQueueDropBytesNumber of bytes discarded when enqueued by tail-drop/wred method.
It's zero if the system does not support queue drop statistics.roobsolete Counter64 .1.3.6.1.4.1.52642.1.8.10.3.3.1.6 |
qosStatsCbPolicyAceBasedRunInfoTableA table of Running Stats for matching QoS policy Ace applied on the interface. The matching ace statistics is only for match-any class-map in policy-map SEQUENCE OF QosStatsCbPolicyAceBasedRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.4 |
qosStatsCbPolicyAceBasedRunInfoEntryPolicy Stats information entry. QosStatsCbPolicyAceBasedRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.4.1 |
qosStatsCbAceBasedIfIndexInterface Index, equal to ifIndex. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.4.1.1 |
qosStatsCbAceBasedDirectionPolicy direction:
inbound (1)
outbound (2) DirectionType .1.3.6.1.4.1.52642.1.8.10.3.4.1.2 |
qosStatsCbAceBasedPolicyClassIndexPolicyClass index in policy-map. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.4.1.3 |
qosStatsCbAceBasedMatchRuleIndexMatch rule index in Class-map. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.4.1.4 |
qosStatsCbAceBasedAclGroupRuleIndexRule index(sequence num in cli) in acl Group. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.4.1.5 |
qosStatsCbAceBasedPktsNumber of packets matching ace in policy-map.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.4.1.6 |
qosStatsCbAceBasedBytesBytes of packets matching ace in policy-map.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.4.1.7 |
qosStatsAggPolicyRunInfoTableA table of Running Stats in a QoS aggregate policy applied on the interface. SEQUENCE OF QosStatsAggPolicyRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.5 |
qosStatsAggPolicyRunInfoEntryAggregate Policy Stats information entry. QosStatsAggPolicyRunInfoEntry .1.3.6.1.4.1.52642.1.8.10.3.5.1 |
qosStatsAggPolicyIndexIndex of aggregate-policer. Integer32 .1.3.6.1.4.1.52642.1.8.10.3.5.1.1 |
qosStatsAggPolicyRedPacketsNumber of red packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.5.1.2 |
qosStatsAggPolicyRedBytesNumber of red bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.5.1.3 |
qosStatsAggPolicyGreenPacketsNumber of green packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.5.1.4 |
qosStatsAggPolicyGreenBytesNumber of green bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.5.1.5 |
qosStatsAggPolicyYellowPacketsNumber of yellow packets.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.5.1.6 |
qosStatsAggPolicyYellowBytesNumber of yellow bytes.ro Counter64 .1.3.6.1.4.1.52642.1.8.10.3.5.1.7 |
igsp OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.9 |
lswIgmpsnoopingMibObject OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.9.1 |
igmpSnoopingStatusConfigure to enable IGMP Snooping.
enable(1)
disable(2)rw Enumeration .1.3.6.1.4.1.52642.1.9.1.1 |
igmpSnoopingFastLeaveStatusConfigure to enable IGMP Snooping Fast Leave.
enable(1)
disable(2)rw Enumeration .1.3.6.1.4.1.52642.1.9.1.2 |
igmpSnoopingVersionConfigure to set IGMP Snooping Version.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.3 |
igmpSnoopingMaxMemberNumberConfigure the max member number.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.4 |
igmpSnoopingDiscardUnknownstatusConfigure to enable IGMP Snooping Discard unknown multicast traffic.
enable(1)
disable(2)rw Enumeration .1.3.6.1.4.1.52642.1.9.1.5 |
igmpSnoopingReportSuppressionStatusConfigure to enable IGMP Snooping Report-Suppression.
enable(1)
disable(2)rw Enumeration .1.3.6.1.4.1.52642.1.9.1.6 |
igmpSnoopingLastMemberQueryIntervalConfigure to set IGMP Snooping Last Member Query Interval. Interval range 1000~25500.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.7 |
igmpSnoopingQueryIntervalConfigure to set IGMP Snooping Query Interval.Must more than query max response time. Interval range 2~18000.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.8 |
igmpSnoopingQueryMaxResponseTimeConfigure to set IGMP Snooping Query Max Response Time.Time range 1~25.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.9 |
igmpSnoopingVlanTableThe table contains, one entry per vlan,
infomation about the IGMP Snooping. SEQUENCE OF IgmpSnoopingVlanEntry .1.3.6.1.4.1.52642.1.9.1.10 |
igmpSnoopingVlanEntryEntry containing information about the
IGMP Snooping on vlan. IgmpSnoopingVlanEntry .1.3.6.1.4.1.52642.1.9.1.10.1 |
igmpSnoopingVlanIDAn index uniquely identifies the VLAN id which IGMP
snooping is enabled or disabled. Integer32 .1.3.6.1.4.1.52642.1.9.1.10.1.1 |
igmpSnoopingVlanEnabledIndicating whether IGMP snooping is enabled on this VLAN.
enable(1)
disable(2)rw Enumeration .1.3.6.1.4.1.52642.1.9.1.10.1.2 |
igmpSnoopingVlanFastLeaveStatusConfigure to enable IGMP Snooping Fast Leave on VLAN,
enable(1)
disable(2).rw Enumeration .1.3.6.1.4.1.52642.1.9.1.10.1.3 |
igmpSnoopingVlanReportSuppressionStatusConfigure to enable IGMP Snooping Report-Suppression on VLAN.
enable(1)
disable(2)rw Enumeration .1.3.6.1.4.1.52642.1.9.1.10.1.4 |
igmpSnoopingVlanVersionConfigure to set IGMP Snooping Version on VLAN.Version range 1~3.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.10.1.5 |
igmpSnoopingVlanMaxMemberNumberConfigure the max member number on VLAN.Range 1~8192.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.10.1.6 |
igmpSnoopingVlanDiscardUnknownStatusConfigure to enable IGMP Snooping Discard unknown multicast traffic on VLAN.
enable(1)
disable(2)rw Enumeration .1.3.6.1.4.1.52642.1.9.1.10.1.7 |
igmpSnoopingVlanGroupAccesslistConfigure the IGMP Snooping Group Acess-list on VLAN.rw OCTET STRING .1.3.6.1.4.1.52642.1.9.1.10.1.8 |
igmpSnoopingVlanLastMemberQueryIntervalConfigure to set IGMP Snooping Last Member Query Interval on VLAN. Interval range 1000~25500.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.10.1.10 |
igmpSnoopingVlanQuerierConfigure to Enable or Disable IGMP Snooping Querier on VLAN.
enable(1)
disable(2)rw EnabledStatus .1.3.6.1.4.1.52642.1.9.1.10.1.11 |
igmpSnoopingVlanQuerierOperationalAddressConfigure to get IGMP Snooping Querier Operational Adress on VLAN.ro IpAddress .1.3.6.1.4.1.52642.1.9.1.10.1.12 |
igmpSnoopingVlanQuerierConfigureAddressConfigure to set IGMP Snooping Querier Configure Adress on VLAN.rw IpAddress .1.3.6.1.4.1.52642.1.9.1.10.1.13 |
igmpSnoopingVlanQuerierTimeoutConfigure to set IGMP Snooping Querier Timeout value on VLAN. Timeout range 60~300.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.10.1.14 |
igmpSnoopingVlanQueryIntervalConfigure to set IGMP Snooping Query Interval on VLAN. Query interval should be greater than Query Response Interval. Interval range 2~18000.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.10.1.15 |
igmpSnoopingVlanQueryMaxResponseTimeConfigure to set IGMP Snooping Query Max Response Time on VLAN.rw INTEGER .1.3.6.1.4.1.52642.1.9.1.10.1.16 |
igmpSnoopingVlanStatusGrpJoinsCntConfigure to get IGMP Snooping Group Joins Count on VLAN.roobsolete Counter32 .1.3.6.1.4.1.52642.1.9.1.10.1.17 |
igmpSnoopingVlanStatusGrpLeavesCntConfigure to get IGMP Snooping Group Leaves Count on VLAN.roobsolete Counter32 .1.3.6.1.4.1.52642.1.9.1.10.1.18 |
igmpSnoopingVlanStatusV1QuerierWCntConfigure to get IGMP Snooping Group V1-Querier Warnings Count on VLAN.roobsolete Counter32 .1.3.6.1.4.1.52642.1.9.1.10.1.19 |
igmpSnoopingVlanStatusV2QuerierWCntConfigure to get IGMP Snooping Group V2-Querier Warnings Count on VLAN.roobsolete Counter32 .1.3.6.1.4.1.52642.1.9.1.10.1.20 |
igmpSnoopingVlanStatusResetCountersConfigure to reset IGMP SnoopingStatus Counters on VLAN.
1 reset.rwobsolete Enumeration .1.3.6.1.4.1.52642.1.9.1.10.1.21 |
igmpSnoopingVlanGrpNumConfigure to get IGMP Snooping group number on VLAN.ro INTEGER .1.3.6.1.4.1.52642.1.9.1.10.1.22 |
igmpSnoopingVlanElectedQuerierAddressConfigure to get IGMP Snooping Elected Querier Adress on VLAN.ro IpAddress .1.3.6.1.4.1.52642.1.9.1.10.1.23 |
igmpSnoopingMrouterPortTableA table that contains information about igmp snooping mrouter port list
per vlan. SEQUENCE OF IgmpSnoopingMrouterPortEntry .1.3.6.1.4.1.52642.1.9.1.11 |
igmpSnoopingMrouterPortEntryInformation about IGMP Snooping Mrouter Port on VLAN. IgmpSnoopingMrouterPortEntry .1.3.6.1.4.1.52642.1.9.1.11.1 |
igmpSnoopingVlanidThe VLAN identifier of this mrouter port. Integer32 .1.3.6.1.4.1.52642.1.9.1.11.1.1 |
igmpSnoopingmrouterPortmrouter port ifindex .
1~1024 is switch port, 1025~1151 is agg port(agg1~127). Integer32 .1.3.6.1.4.1.52642.1.9.1.11.1.2 |
igmpSnoopingmrouterPortRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.9.1.11.1.3 |
igmpSnoopingGrpNumConfigure to get IGMP Snooping total group number.ro INTEGER .1.3.6.1.4.1.52642.1.9.1.12 |
lswIgmpsnoopingTrap OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.9.2 |
igmpSnoopingGrplimitReachIgmp snooping group record reaches total limit NOTIFICATION-TYPE .1.3.6.1.4.1.52642.1.9.2.1 |
igmpSnoopingVlanGrplimitReachIgmp snooping group record reaches limit on vlan NOTIFICATION-TYPE .1.3.6.1.4.1.52642.1.9.2.2 |
igmpSnoopingVlanQuerierSwitchIgmp snooping group querier changes NOTIFICATION-TYPE .1.3.6.1.4.1.52642.1.9.2.3 |
linkAgg OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.10 |
linkAggLoadBalanceConfig load balance.
1 dst-mac.
2 src-mac.
3 src-ip.
4 dst-ip.
5 src-port.
6 dst-port.
7 ip-protocol.
8 vxlan-vni.
9 nvgre-vsid.
10 inner-dst-mac.
11 inner-src-mac.
12 inner-src-ip.
13 inner-dst-ip.
14 inner-src-port.
15 inner-dst-port.
16 inner-ip-protocol.rw Bits .1.3.6.1.4.1.52642.1.10.1 |
lacpObject OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.10.2 |
lacpSysPriorityCfg OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.10.2.1 |
lacpSysPriorityConfig lacp system priority.rw Integer32 .1.3.6.1.4.1.52642.1.10.2.1.1 |
lacpIfCfgTableThis table is used for lacp configuration on interface. SEQUENCE OF LacpIfCfgEntry .1.3.6.1.4.1.52642.1.10.2.2 |
lacpIfCfgEntryThis table is used for lacp configuration on interface. LacpIfCfgEntry .1.3.6.1.4.1.52642.1.10.2.2.1 |
lacpIfCfgAdminAggNumberConfig channel group number. Integer32 .1.3.6.1.4.1.52642.1.10.2.2.1.1 |
lacpIfCfgModeThe channel group mode.rw Enumeration .1.3.6.1.4.1.52642.1.10.2.2.1.2 |
lacpIfCfgRowStatusThe status of this conceptual row.Now only realize CreateAndGo and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.10.2.2.1.3 |
lacpIfCfgParaTableThis table is used for lacp configuration on interface. SEQUENCE OF LacpIfCfgParaEntry .1.3.6.1.4.1.52642.1.10.2.3 |
lacpIfCfgParaEntryThis table is used for lacp configuration on interface. LacpIfCfgParaEntry .1.3.6.1.4.1.52642.1.10.2.3.1 |
lacpIfCfgParaPriorityConfig lacp priority on interface.rw Integer32 .1.3.6.1.4.1.52642.1.10.2.3.1.1 |
lacpIfCfgParaTimeOutConfig lacp expire timer on interface.rw Enumeration .1.3.6.1.4.1.52642.1.10.2.3.1.2 |
lacpPortStateTableThis table is used for displaying port state of interface. SEQUENCE OF LacpPortStateEntry .1.3.6.1.4.1.52642.1.10.2.4 |
lacpPortStateEntryThis table is used for lacp configuration on interface. LacpPortStateEntry .1.3.6.1.4.1.52642.1.10.2.4.1 |
lacpPortStateGroupNumDisplay port state. Integer32 .1.3.6.1.4.1.52642.1.10.2.4.1.1 |
lacpPortStateDisplay port state.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.4.1.2 |
lacpActorStateTableThis table is used for displaying actor state. SEQUENCE OF LacpActorStateEntry .1.3.6.1.4.1.52642.1.10.2.5 |
lacpActorStateEntryThis table is used for displaying actor state. LacpActorStateEntry .1.3.6.1.4.1.52642.1.10.2.5.1 |
lacpActorGroupNumDisplay actor group number. Integer32 .1.3.6.1.4.1.52642.1.10.2.5.1.1 |
lacpActorSystemIdDisplay actor system id.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.2 |
lacpActorPortNumDisplay actor port number.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.5.1.3 |
lacpActorPortTransitPduTypeDisplay actor port number. It should be 'fast' or 'slow'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.4 |
lacpActorPortModeDisplay actor port mode. It should be 'active' or 'passive'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.5 |
lacpActorPortPriorityDisplay actor port priority.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.5.1.6 |
lacpActorPortOperKeyDisplay actor port operate key.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.5.1.7 |
lacpActorPortStatsFlagDisplay actor port stats flag.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.8 |
lacpActorPortActivityDisplay actor port activity. It should be 'active' or 'passive'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.9 |
lacpActorPortTimeoutDisplay actor port timeout. It should be 'short' or 'long'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.10 |
lacpActorPortAggregationDisplay actor port number. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.11 |
lacpActorPortSynchronizationDisplay actor port synchronization. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.12 |
lacpActorPortCollectingDisplay actor port collecting. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.13 |
lacpActorPortDistributingDisplay actor port distributing. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.14 |
lacpActorPortDefaultedDisplay actor port defaulted. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.15 |
lacpActorPortExpiredDisplay actor port expired . It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.5.1.16 |
lacpNeighborStateTableThis table is used for displaying neighbor state. SEQUENCE OF LacpNeighborStateEntry .1.3.6.1.4.1.52642.1.10.2.6 |
lacpNeighborStateEntryThis table is used for displaying neighbor state. LacpNeighborStateEntry .1.3.6.1.4.1.52642.1.10.2.6.1 |
lacpNeighborGroupNumdisplay neighbor group number. Integer32 .1.3.6.1.4.1.52642.1.10.2.6.1.1 |
lacpNeighborSystemIdDisplay neighbor system id.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.2 |
lacpNeighborPortNumDisplay neighbor port number.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.6.1.3 |
lacpNeighborPortTransitPduTypeDisplay neighbor port transmit pdu. It should be 'fast' or 'slow'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.4 |
lacpNeighborPortModeDisplay neighbor port mode. It should be 'active' or 'passive'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.5 |
lacpNeighborPortPriorityDisplay neighbor port number.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.6.1.6 |
lacpNeighborOperKeyDisplay neighbor operational key.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.6.1.7 |
lacpNeighborPortStatsFlagDisplay neighbor stats flag.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.8 |
lacpNeighborPortActivityDisplay neighbor stats flag. It should be 'active' or 'passive'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.9 |
lacpNeighborPortTimeoutDisplay neighbor stats flag. It should be 'short' or 'long'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.10 |
lacpNeighborPortAggregationDisplay neighbor stats flag. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.11 |
lacpNeighborPortSynchronizationDisplay neighbor stats flag. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.12 |
lacpNeighborPortCollectingDisplay neighbor stats flag. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.13 |
lacpNeighborPortDistributingDisplay neighbor stats flag. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.14 |
lacpNeighborPortDefaultedDisplay neighbor stats flag. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.15 |
lacpNeighborPortExpiredDisplay neighbor stats flag. It should be 'yes' or 'no'.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.2.6.1.16 |
lacpCounterTableThis table is used for displaying neighbor state. SEQUENCE OF LacpCounterEntry .1.3.6.1.4.1.52642.1.10.2.7 |
lacpCounterEntryThis table is used for displaying neighbor state. LacpCounterEntry .1.3.6.1.4.1.52642.1.10.2.7.1 |
lacpCounterGroupNumDisplay lacp group number. Integer32 .1.3.6.1.4.1.52642.1.10.2.7.1.1 |
lacpCounterSendPduCntDisplay lacp send pdu counts.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.7.1.2 |
lacpCounterRecvPduCntDisplay neighbor receive pdu counts.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.7.1.3 |
lacpCounterSendErrPktCntDisplay neighbor send error packet counts.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.7.1.4 |
lacpCounterRecvErrPktCntDisplay neighbor recevie error packet counts.ro Integer32 .1.3.6.1.4.1.52642.1.10.2.7.1.5 |
lacpClearCntCfg OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.10.2.8 |
lacpClearCounterclear lacp counter. The system will clear all lacp's couter if the value is '0'.rw Integer32 .1.3.6.1.4.1.52642.1.10.2.8.1 |
staticLinkAggObject OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.10.3 |
staticLinkAggTableThis table stores the link aggregator number, name and
configure type and memberlist. SEQUENCE OF StaticLinkAggEntry .1.3.6.1.4.1.52642.1.10.3.1 |
staticLinkAggEntryThis table stores the link aggregator number, name and configure type
and memberlist. StaticLinkAggEntry .1.3.6.1.4.1.52642.1.10.3.1.1 |
staticLinkAggNumberThe number of Link aggregator interface.This is the index of Link
Aggregator table. Integer32 .1.3.6.1.4.1.52642.1.10.3.1.1.1 |
staticLinkAggIndexThe index of link aggregator interface.ro Integer32 .1.3.6.1.4.1.52642.1.10.3.1.1.2 |
staticLinkAggNameThe name of link aggregator interface.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.3.1.1.3 |
staticLinkAggMemberIndexThe index of interface member added to link aggregator.ro Integer32 .1.3.6.1.4.1.52642.1.10.3.1.1.4 |
staticLinkAggMemberNameThe name of interface member added to link aggregator.ro OCTET STRING .1.3.6.1.4.1.52642.1.10.3.1.1.5 |
staticLinkAggMemberEnableThe member is Bundle when the value is 1.
the member is down when the value is 0.
the member is admin down when the value is 2.ro Enumeration .1.3.6.1.4.1.52642.1.10.3.1.1.6 |
staticLinkAggMemberRowStatusThe status of this conceptual row.Now only realize CreateAndGo
and Destroy and Active.
1 means Active
4 means CreateAndGo
6 means Destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.10.3.1.1.7 |
qBridgeExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.11 |
vlanExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.11.1 |
vlanTableA table that contains information about VLAN entries
of the device. SEQUENCE OF VlanEntry .1.3.6.1.4.1.52642.1.11.1.1 |
vlanEntryInformation about a specific VLAN of the device. VlanEntry .1.3.6.1.4.1.52642.1.11.1.1.1 |
vlanIndexAn forward ID, which may be same as VLAN ID in IVL mode. VlanIndex .1.3.6.1.4.1.52642.1.11.1.1.1.1 |
vlanNameAn administratively assigned string, which may be used to identify the VLAN.rw OCTET STRING .1.3.6.1.4.1.52642.1.11.1.1.1.2 |
vlanStatusAn administratively VLANStatus .
1 Inactive;
2 Active(2).rw Enumeration .1.3.6.1.4.1.52642.1.11.1.1.1.3 |
vlanRowStatusThe status of this conceptual row.Now only realize CreateAndGo(4) and Destroy(6) and Active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.52642.1.11.1.1.1.4 |
vlanIfConfigThis object create/destroy vlan interface.
1 Create.
2 Destroy.rw Enumeration .1.3.6.1.4.1.52642.1.11.1.1.1.5 |
vlanStatsPktInIngress packtes number of Vlan.ro Counter64 .1.3.6.1.4.1.52642.1.11.1.1.1.7 |
vlanStatsPktOutEgress packtes number of Vlan.ro Counter64 .1.3.6.1.4.1.52642.1.11.1.1.1.8 |
vlanStatsByteInIngress bytes number of Vlan.ro Counter64 .1.3.6.1.4.1.52642.1.11.1.1.1.9 |
vlanStatsByteOutEgress bytes number of Vlan.ro Counter64 .1.3.6.1.4.1.52642.1.11.1.1.1.10 |
vlanStatsEnThe status of this conceptual row.Now only realize Active(1) and Inactive(0).rw Enumeration .1.3.6.1.4.1.52642.1.11.1.1.1.11 |
portVlanTableA table that contains information about interface's VLAN properties. SEQUENCE OF PortVlanEntry .1.3.6.1.4.1.52642.1.11.1.2 |
portVlanEntryInformation about a specific interface's VLAN properties. PortVlanEntry .1.3.6.1.4.1.52642.1.11.1.2.1 |
fdbExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.11.2 |
vlanClass OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.11.3 |
dot1xExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.12 |
timeRange OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.13 |
stpExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.14 |
igmpExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.16 |
boardHealthyMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.17 |
arpInsp OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.20 |
pimsmExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.21 |
ospfExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.22 |
user OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.30 |
snmpExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.32 |
stm OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.33 |
dnsClient OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.34 |
ssh OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.35 |
dhcp OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.36 |
lswdevMMib OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.37 |
lswTrapMib OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.39 |
ipSourceGuard OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.40 |
vrrpExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.41 |
interface OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.42 |
management OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.43 |
mvr OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.44 |
erps OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.45 |
prefixList OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.46 |
ipUnicast OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.47 |
vrf OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.48 |
aaa OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.49 |
evc OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.51 |
qinq OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.52 |
rmonExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.53 |
routeMap OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.54 |
ripExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.57 |
ldpExt OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.60 |
bgp OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.68 |
mpls OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.69 |
smartlink OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.70 |
flowctrl OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.71 |
cputraffic OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.72 |
portisolate OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.73 |
phyloopback OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.74 |
monitorlink OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.75 |
udld OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.76 |
policyBasedRouting OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.77 |
ddos OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.78 |
l2ping OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.79 |
ipg OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.80 |
syncE OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.81 |
arpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.82 |
cfm OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.83 |
efm OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.84 |
ptp OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.85 |
pm OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.90 |
alarm OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.91 |
rsvpTe OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.92 |
g8031 OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.93 |
g8032 OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.94 |
voiceVlan OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.95 |
ivi OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.96 |
product OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99 |
e3008TSE300,8TS. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3080 |
e30016TXE300,16TX. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3160 |
e3508T12XE350,8T12X. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3200 |
e30024TSE300,24TS. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3240 |
e30024STE300,24ST. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3241 |
e30048TSE300,48TS. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3480 |
b30048TB300,48T. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3481 |
e33048TE330,48T. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3485 |
e33048SEE330,48SE. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3486 |
e33048SE330,48S. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3487 |
g24euG24EU,24+4. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3488 |
e35048T4XE350,48T4X. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.3520 |
e55024T16XE550,24T16X. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5501 |
e55024T16YE550,24T16Y. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5502 |
e58024QE580,24Q. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5801 |
e58048X2Q4ZE580,48X2Q4Z. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5802 |
e58048X6QE580,48X6Q. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5803 |
e58032X2QE580,32X2Q. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5804 |
e58032XE580,32X. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5805 |
e58020Q4ZE580,20Q4Z. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.5806 |
e602E600,2 slots. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.6020 |
e606E600,6 slots. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.6060 |
e614E600,14 slots. OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.6140 |
e802E800,2 slots OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.8020 |
e806E800,6 slots OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.8060 |
e814E800,14 slots OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.99.8140 |
l2protocol OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.100 |
loopbackDetect OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.105 |
ipsla OBJECT IDENTIFIER .1.3.6.1.4.1.52642.1.106 |
vlanTagTypeall(1)
qinq(2)
untagged(3)
::= { portVlanEntry 1 }
pvid OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTIONrw Enumeration .ipslaTrap.4 |