Home/Catalog/FS-FIBER-MIB

FS-FIBER-MIB

AI MIB Summary

The FS-FIBER-MIB enables monitoring of optical transceiver parameters and fiber link status on FS (FiberStore) network hardware via SNMP, specifically tracking metrics such as optical power levels, laser bias currents, temperature, and voltage.

This module defines fs fiber module information mibs.
Main OID:
fsFiberMIB.1.3.6.1.4.1.52642.1.1.10.2.105
206
Objects
Active
Status
6
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
SNMPv2-CONF
FS-TC
FS-SMI
IF-MIB

Objects

206 total
Object Name
fsFiberMIBThis module defines fs fiber module information mibs.
MODULE-IDENTITY
.1.3.6.1.4.1.52642.1.1.10.2.105
fsFiberMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.52642.1.1.10.2.105.1
fsFiberTableA table for getting Fiber Module information
SEQUENCE OF FSFiberEntry
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1
fsFiberEntryEntry of a Fiber Module information.
FSFiberEntry
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1
fsFiberPortIndexPort index of the port.ro
IfIndex (FS-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.1
fsFiberPortDescrDiscription of the port.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.2
fsFiberTransceiverTypeTransceiver type of the Fiber module insered into the port.ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.3
fsFiberConnectorTypeConnector type of the Fiber module insered into the port. If the transceiver type of Fiber module is unknown(1), then this object contains a zero value.ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.4
fsFiberWavelengthThe value of wavelength of the Fiber module insered into the port. If the transceiver type of Fiber module is either fiber100CopperSFP(7) or fiber1000CopperSFP(13) (or fiber10GCopperSFPPlus(14), or fiber10GCopperXFP(19), or fiber40GCopperQSFPPlus(26), or fiber2500CopperSFP(28), or unknown(1)), then this object contains a zero value.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.5
fsFiberTransferDistanceSMFThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber for. The value is in units of kilometers. A value of zero means that the transceiver does not support single mode fiber.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.6
fsFiberTransferDistance62point5umOM1The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 62.5 micron multimode (200 MHz*Km at 850 nm, 500 MHz*Km at 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.7
fsFiberTransferDistance62point5umThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 62.5 micron core multimode (200 MHz*Km at 850 nm, 500 MHz*Km at 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the Fiber module type is not XFP.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.8
fsFiberTransferDistance50umOM2The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode (500 MHz*Km at 850 nm for SFP module or at 850 nm and 1310 nm for QSFP+ module) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.9
fsFiberTransferDistance50umThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron core multimode (500 MHz*Km at 850 nm and 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron core multimode fiber or the Fiber module type is not XFP.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.10
fsFiberTransferDistance50umOM3The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode OM3(2000 MHz*Km) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.11
fsFiberTransferDistanceEBW50umThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 2000 MHz*Km (850nm) extended bandwidth 50 micron core multimode fiber. The value is in units of meters. A value of zero means that the transceiver does not support extended bandwidth 50 micron multimode fiber or the Fiber module type is not XFP.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.12
fsFiberTransferDistanceCopperThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using copper cables. The value is in units of meters. A value of zero means that the transceiver does not support copper cables or the Fiber module type is neither SFP/SFP+ nor XFP.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.13
fsFiberTransferDistanceCableAssemblyThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length of the Cable assembly passive. The value is in units of meters. A value of zero means that the transceiver is not a cable assemblyor or the Fiber module type is not QSFP+.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.14
fsFiberDDMSupportStatusThis object indicates that whether the Digital Diagnostic Monitors is implemeted.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.15
fsFiberSerialNumberThe serial number of the Fiber module insered into the port.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.16
fsFiberTempThe temperature of the Fiber module insered into the port. The value is in units of degrees Celsius. If the fsFiberDDMSupportStatus is false, the temperature value is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.17
fsFiberTempStatusThe status ok(2) indicates that the temperature of the Fiber module is in the normal level. The status warning(3) indicates that the temperature of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the temperature of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.18
fsFiberVoltageThe voltage of the Fiber module insered into the port. The value is in units of mVolts. If the fsFiberDDMSupportStatus is false, the voltage value is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.19
fsFiberVoltageStatusThe status ok(2) indicates that the voltage of the Fiber module is in the normal level. The status warning(3) indicates that the voltage of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the voltage of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.20
fsFiberBiasThe bias of the Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the bias value is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.21
fsFiberBiasStatusThe status ok(2) indicates that the bias of the Fiber module is in the normal level. The status warning(3) indicates that the bias of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.22
fsFiberChannel1BiasThe bias in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 1 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.23
fsFiberChannel1BiasStatusThe status ok(2) indicates that the bias in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 1 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.24
fsFiberChannel2BiasThe bias in Channel 2 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 2 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.25
fsFiberChannel2BiasStatusThe status ok(2) indicates that the bias in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 2 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.26
fsFiberChannel3BiasThe bias in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 3 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.27
fsFiberChannel3BiasStatusThe status ok(2) indicates that the bias in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 3 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.28
fsFiberChannel4BiasThe bias in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 4 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.29
fsFiberChannel4BiasStatusThe status ok(2) indicates that the bias in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 4 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.30
fsFiberRXpowerIntegerpartThe integer part of Rx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Rx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.31
fsFiberRXpowerDecimalpartThe decimal part of Rx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the decimal part of Rx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.32
fsFiberRXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3). If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP (or not QSFP+), the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.33
fsFiberRXpowerStatusThe status ok(2) indicates that the Rx power of the Fiber module is in the normal level. The status warning(3) indicates that the Rx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.34
fsFiberChannel1RXpowerIntegerpartThe integer part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.35
fsFiberChannel1RXpowerDecimalpartThe decimal part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.36
fsFiberChannel1RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 1 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.37
fsFiberChannel1RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 1 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.38
fsFiberChannel2RXpowerIntegerpartThe integer part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.39
fsFiberChannel2RXpowerDecimalpartThe decimal part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 2 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.40
fsFiberChannel2RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 2 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.41
fsFiberChannel2RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 2 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.42
fsFiberChannel3RXpowerIntegerpartThe integer part of Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.43
fsFiberChannel3RXpowerDecimalpartThe decimal part of Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.44
fsFiberChannel3RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 3 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.45
fsFiberChannel3RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 3 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.46
fsFiberChannel4RXpowerIntegerpartThe integer part of Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.47
fsFiberChannel4RXpowerDecimalpartThe decimal part of Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.48
fsFiberChannel4RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 4 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.49
fsFiberChannel4RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 4 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.50
fsFiberTXpowerIntegerpartThe integer part of Tx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Tx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.51
fsFiberTXpowerDecimalpartThe decimal part of Tx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the decimal part of Tx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.52
fsFiberTXpowerStatusThe status ok(2) indicates that the Tx power of the Fiber module is in the normal level. The status warning(3) indicates that the Tx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.53
fsFiberChannel1TXpowerIntegerpartThe integer part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.54
fsFiberChannel1TXpowerDecimalpartThe decimal part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.55
fsFiberChannel1TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 1 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.56
fsFiberChannel2TXpowerIntegerpartThe integer part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.57
fsFiberChannel2TXpowerDecimalpartThe decimal part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 2 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.58
fsFiberChannel2TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 2 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.59
fsFiberChannel3TXpowerIntegerpartThe integer part of Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.60
fsFiberChannel3TXpowerDecimalpartThe decimal part of Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.61
fsFiberChannel3TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 3 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.62
fsFiberChannel4TXpowerIntegerpartThe integer part of Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.63
fsFiberChannel4TXpowerDecimalpartThe decimal part of Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.64
fsFiberChannel4TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 4 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.65
fsFiberRXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.66
fsFiberChannel1RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.67
fsFiberChannel2RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.68
fsFiberChannel3RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.69
fsFiberChannel4RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.70
fsFiberTXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.71
fsFiberChannel1TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.72
fsFiberChannel2TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.73
fsFiberChannel3TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.74
fsFiberChannel4TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.75
fsFiberRXpowerThe Rx power of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.76
fsFiberChannel1RXpowerThe Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.77
fsFiberChannel2RXpowerThe Rx power in Channel 2 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.78
fsFiberChannel3RXpowerThe Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.79
fsFiberChannel4RXpowerThe Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.80
fsFiberTXpowerThe Tx power of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.81
fsFiberChannel1TXpowerThe Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.82
fsFiberChannel2TXpowerThe Tx power in Channel 2 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.83
fsFiberChannel3TXpowerThe Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.84
fsFiberChannel4TXpowerThe Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.85
fsFiberWavelengthExactThe value of wavelength of the Fiber module insered into the port. If the transceiver type of Fiber module is either fiber100CopperSFP(7) or fiber1000CopperSFP(13) (or fiber10GCopperSFPPlus(14), or fiber10GCopperXFP(19), or fiber40GCopperQSFPPlus(26), or fiber2500CopperSFP(28), or unknown(1)), then this object contains a NA value.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.86
fsFiberTransferDistance50umOM4The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode OM4(4700 MHz*Km) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.87
fsFiberTransferDistanceSMFExtThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber for. The value is in units of meters. A value of zero means that the transceiver does not support single mode fiber.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.88
fsFiberBandWidthThe value of transfer maximum available bandwidth of the Fiber module insered into the port. The value is in units of Mbit/s. A value of zero means that the transceiver does not insert or unknown type.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.89
fsFiberFormFactorIndicates the form factor of the Fiber module insered into the port.ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.90
fsFiberRXpowerLowWarnThresholdThe Rx power low warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.91
fsFiberRXpowerHighWarnThresholdThe Rx power high warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.92
fsFiberRXpowerLowAlarmThresholdThe Rx power low alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.93
fsFiberRXpowerHighAlarmThresholdThe Rx power high alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.94
fsFiberTXpowerLowWarnThresholdThe Tx power low warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.95
fsFiberTXpowerHighWarnThresholdThe Tx power high warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.96
fsFiberTXpowerLowAlarmThresholdThe Tx power low alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.97
fsFiberTXpowerHighAlarmThresholdThe Tx power high alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.98
fsFiberChannel5BiasThe bias in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 5 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.99
fsFiberChannel5BiasStatusThe status ok(2) indicates that the bias in the Channel 5 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 5 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 5 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.100
fsFiberChannel6BiasThe bias in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 6 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.101
fsFiberChannel6BiasStatusThe status ok(2) indicates that the bias in the Channel 6 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 6 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 6 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.102
fsFiberChannel7BiasThe bias in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 7 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.103
fsFiberChannel7BiasStatusThe status ok(2) indicates that the bias in the Channel 7 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 7 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 7 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.104
fsFiberChannel8BiasThe bias in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 8 is 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.105
fsFiberChannel8BiasStatusThe status ok(2) indicates that the bias in the Channel 8 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 8 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 8 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.106
fsFiberChannel5RXpowerIntegerpartThe integer part of Rx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.107
fsFiberChannel5RXpowerDecimalpartThe decimal part of Rx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.108
fsFiberChannel5RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 5 of QSFP CMIS. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.109
fsFiberChannel5RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 5 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 5 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 5 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.110
fsFiberChannel6RXpowerIntegerpartThe integer part of Rx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.111
fsFiberChannel6RXpowerDecimalpartThe decimal part of Rx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.112
fsFiberChannel6RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 6 of QSFP CMIS. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.113
fsFiberChannel6RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 6 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 6 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 6 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.114
fsFiberChannel7RXpowerIntegerpartThe integer part of Rx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.115
fsFiberChannel7RXpowerDecimalpartThe decimal part of Rx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.116
fsFiberChannel7RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 7 of QSFP CMIS. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.117
fsFiberChannel7RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 7 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 7 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 7 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.118
fsFiberChannel8RXpowerIntegerpartThe integer part of Rx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.119
fsFiberChannel8RXpowerDecimalpartThe decimal part of Rx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.120
fsFiberChannel8RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 8 of QSFP CMIS. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.121
fsFiberChannel8RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 8 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 8 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 8 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.122
fsFiberChannel5TXpowerIntegerpartThe integer part of Tx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.123
fsFiberChannel5TXpowerDecimalpartThe decimal part of Tx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.124
fsFiberChannel5TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 5 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 5 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 5 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.125
fsFiberChannel6TXpowerIntegerpartThe integer part of Tx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.126
fsFiberChannel6TXpowerDecimalpartThe decimal part of Tx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.127
fsFiberChannel6TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 6 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 6 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 6 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.128
fsFiberChannel7TXpowerIntegerpartThe integer part of Tx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.129
fsFiberChannel7TXpowerDecimalpartThe decimal part of Tx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.130
fsFiberChannel7TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 7 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 7 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 7 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.131
fsFiberChannel8TXpowerIntegerpartThe integer part of Tx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.132
fsFiberChannel8TXpowerDecimalpartThe decimal part of Tx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.133
fsFiberChannel8TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 8 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 8 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 8 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.134
fsFiberChannel5RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.135
fsFiberChannel6RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.136
fsFiberChannel7RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.137
fsFiberChannel8RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.138
fsFiberChannel5TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.139
fsFiberChannel6TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.140
fsFiberChannel7TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.141
fsFiberChannel8TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.142
fsFiberChannel5RXpowerThe Rx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.143
fsFiberChannel6RXpowerThe Rx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.144
fsFiberChannel7RXpowerThe Rx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.145
fsFiberChannel8RXpowerThe Rx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.146
fsFiberChannel5TXpowerThe Tx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.147
fsFiberChannel6TXpowerThe Tx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.148
fsFiberChannel7TXpowerThe Tx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.149
fsFiberChannel8TXpowerThe Tx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.150
fsFiberTransferDistance50umOM5The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode OM5(4700 MHz*Km at 850nm, 2470 MHz*km at 953nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.151
fsFiberModeThis object indicates the fiber type.ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.152
fsFiberTempLowWarnThresholdThe temperature low warning threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.153
fsFiberTempHighWarnThresholdThe temperature high warning threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.154
fsFiberTempLowAlarmThresholdThe temperature low alarm threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.155
fsFiberTempHighAlarmThresholdThe temperature high alarm threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.156
fsFiberVoltageLowWarnThresholdThe voltage low warning threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.157
fsFiberVoltageHighWarnThresholdThe voltage high warning threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.158
fsFiberVoltageLowAlarmThresholdThe voltage low alarm threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.159
fsFiberVoltageHighAlarmThresholdThe voltage high alarm threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.160
fsFiberBiasLowWarnThresholdThe bias low warning threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.161
fsFiberBiasHighWarnThresholdThe bias high warning threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.162
fsFiberBiasLowAlarmThresholdThe bias low alarm threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.163
fsFiberBiasHighAlarmThresholdThe bias high alarm threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.1.1.1.164
fsFiberVendorTableA table of Vendor info entries.
SEQUENCE OF FSFiberVendorEntry
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2
fsFiberVendorEntryEntry contains Vendor info.
FSFiberVendorEntry
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1
fsFiberVendorPortIndexThe port index of Vendor info .ro
IfIndex (FS-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1.1
fsFiberVendorNameThe description of vendor name.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1.2
fsFiberVendorOUIThe description of vendor oui.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1.3
fsFiberVendorPartNumberThe description of vendor part number.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1.4
fsFiberVendorRevThe description of vendor revision.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1.5
fsFiberManufacturingDateThe description of vendor's manufacturing date.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1.6
fsFiberEncodingThe description of vendor's encoding type.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.2.1.7
fsFiberOMCTableA table of OMC fiber info entries.
SEQUENCE OF FSFiberOMCEntry
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3
fsFiberOMCEntryEntry contains OMC fiber info.
FSFiberOMCEntry
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3.1
fsFiberOMCPortIndexPort index of the port.ro
IfIndex (FS-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3.1.1
fsFiberOMCRxpowerThe Rx power of the Fiber module insered into the port. Use a comma to separate multiple optical power values for multiple channels, fill in key-value pairs, connect the key and value with an equal sign, the key is the channel name, and the value is the optical power. The unit of the optical power value is dbw.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3.1.2
fsFiberOMCTxpowerThe Tx power of the Fiber module insered into the port. Use a comma to separate multiple optical power values for multiple channels, fill in key-value pairs, connect the key and value with an equal sign, the key is the channel name, and the value is the optical power. The unit of the optical power value is dbw.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3.1.3
fsFiberOMCWavelengthThe value of wavelength of the Fiber module insered into the port. The unit is nm. If it is a single wavelength, report a single value, for example: 1310. If it is a wavelength range, report the wavelength range, for example: 1310-1312. The reported string does not include the unit.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3.1.4
fsFiberOMCTranslengthThe value of transfer distance of the Fiber module insered into the port. The unit is km. If it is a single distance, report a single value, for example: 20 If there are multiple distances in fiber mode, report multiple sets of data separated by commas. The format of each group of data is a key-value pair, the key and value are connected with =, the key is the fiber grade, and the value is the corresponding distance, such as 'OM1=20, OM2=30'ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3.1.5
fsFiberOMCPortTypePort type of the Fiber module insered into the port.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.1.3.1.6
fsFiberAntifakeMIBTraps
OBJECT IDENTIFIER
.1.3.6.1.4.1.52642.1.1.10.2.105.2
fsFiberAntifakeIntfNameDescThe description of the interface.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.2.1
fsFiberAntifakeSerialNumberDescThe description of the serial number of the fiber module.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.2.2
fsFiberAntifakeTrapWhen detect the fiber module is not original fs fiber module, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.52642.1.1.10.2.105.2.3
fsFiberMIBConformance
OBJECT IDENTIFIER
.1.3.6.1.4.1.52642.1.1.10.2.105.3
fsFiberMIBCompliances
OBJECT IDENTIFIER
.1.3.6.1.4.1.52642.1.1.10.2.105.3.1
fsFiberMIBConplianceThe compliance statement for entities which implement the FS Fiber MIB
Unknown
.1.3.6.1.4.1.52642.1.1.10.2.105.3.1.1
fsFiberMIBGroups
OBJECT IDENTIFIER
.1.3.6.1.4.1.52642.1.1.10.2.105.3.2
fsFiberMIBGroupA collection of objects providing Fiber managment.
Unknown
.1.3.6.1.4.1.52642.1.1.10.2.105.3.2.1
fsFiberAntifakeIntfNameDescGroupObjects that providing a literal description of the interface.
Unknown
.1.3.6.1.4.1.52642.1.1.10.2.105.3.2.2
fsFiberAntifakeSerialNumberDescGroupObjects that providing a literal description of the fiber module serial number.
Unknown
.1.3.6.1.4.1.52642.1.1.10.2.105.3.2.3
fsFiberEventMIBTraps
OBJECT IDENTIFIER
.1.3.6.1.4.1.52642.1.1.10.2.105.4
fsFiberEventReasonThe reason of the fiber invalid event.ro
Enumeration
.1.3.6.1.4.1.52642.1.1.10.2.105.4.1
fsFiberEventDescThe description of the fiber invalid event.ro
DisplayString
.1.3.6.1.4.1.52642.1.1.10.2.105.4.2
fsFiberRemoveEventTrapWhen detect the fiber has been removed, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.52642.1.1.10.2.105.4.3
fsFiberInsertEventTrapWhen detect the fiber has been inserted, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.52642.1.1.10.2.105.4.4
fsFiberInvalidTrapDetect the fiber invalid event.
NOTIFICATION-TYPE
.1.3.6.1.4.1.52642.1.1.10.2.105.4.5
fsFiberInvalidResumeTrapThe fiber resume from invalid event.
NOTIFICATION-TYPE
.1.3.6.1.4.1.52642.1.1.10.2.105.4.6
fsFiberAlarmValueThe realtime value of the fiber invalid event. The value of power is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.4.7
fsFiberAlarmThresholdValueThe threshold value of the fiber invalid event. The value of power is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.52642.1.1.10.2.105.4.8
fsFiberSpeedMismatchWhen detect the fiber has been inserted and the speed of the optical module does not match the speed supported by the interface, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.52642.1.1.10.2.105.4.9
FS-FIBER-MIB - SNMP MIB Reference | MIBs Explorer