STN-ATM-MIB
AI MIB Summary
STN-ATM-MIB provides management and monitoring capabilities for ATM (Asynchronous Transfer Mode) network interfaces and virtual circuits on STN (Sangoma) hardware, tracking critical performance metrics such as cell loss, cell delay, and interface status.
Initial version of this MIB module.
Main OID:
stnAtm.1.3.6.1.4.1.3551.2.6
234
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
234 total| Object Name |
|---|
stnAtmInitial version of this MIB module. MODULE-IDENTITY .1.3.6.1.4.1.3551.2.6 |
stnAtmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1 |
stnAtmLinks OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.1 |
stnVcLinks OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.1.1 |
stnVcLinkTableA list of VC Link entries. SEQUENCE OF StnVcLinkEntry .1.3.6.1.4.1.3551.2.6.1.1.1.1 |
stnVcLinkEntryEntry contains information about a particular VC link. StnVcLinkEntry .1.3.6.1.4.1.3551.2.6.1.1.1.1.1 |
stnVcLinkIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.1 |
stnVcLinkVpiThe VPI value of the VPL. Note that the VPI=0 is not used for a VPL not associated with a VCL. The maximum VPI value cannot exceed the value allowable by the atmInterfaceMaxVpiBits.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.2 |
stnVcLinkVciThe VCI value of the VCL. The maximum VCI value cannot exceed the value allowable by the atmInterfaceMaxVciBits.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.3 |
stnVcLinkRcvTrafDescrReceive traffic descriptor identifier for this VPL.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.4 |
stnVcLinkXmtTrafDescrTransmit traffic descriptor identifier for this VPL.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.5 |
stnVcLinkAalObjectsValidIndicates whether the following AAL objects are valid (whether the local VCL end-point is also the VCC end-point). Transmit traffic descriptor identifier for this VPL.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.6 |
stnVcLinkAalTypeAn instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL is in use. The type of AAL used on this VCC. The AAL type includes AAL1, AAL3/4, and AAL5. The other(4) may be used as a user-defined AAL type. The unknown type indicates that the AAL type cannot be determined.ro Enumeration .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.7 |
stnVcLinkAal5XmtSDUSizeAn instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDUsize in octets that is supported on the transmit direction of this VCC.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.8 |
stnVcLinkAal5RcvSDUSizeAn instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the receive direction of this VCC.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.9 |
stnVcLinkAal5EncapsTypeAn instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the AAL5 SSCS layer. The definitions reference RFC 1483 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.10 |
stnVcLinkCastTypeThe type of topology of a connection (point- to-point, point-to-multipoint). In the case of point-to-multipoint, the orientation of this VPL in the connection. On a host, p2mpRoot indicates that the host is the root of the p2mp connection, p2mpLeaf indicates that the host is a leaf of the p2mp connection. On a switch, p2mpRoot indicates that cells received by the switching fabric from the interface are from the root of the p2mp connection, p2mpLeaf indicates that cells transmitted to the interface from the switching fabric are to the leaf of the p2mp connection.ro Enumeration .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.11 |
stnVcLinkConnKindThe use of call control. An spvcInitiator is always cross-connected to an svcOutgoing, and an spvcTarget is always cross-connected to an svcIncoming.ro Enumeration .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.12 |
stnVcLinkAccEnabledATM accounting is enabled for this VC Link.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.13 |
stnVcLinkOAMMgmtEnabledOAM management is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.14 |
stnVcLinkOAMXmtFrequencyNumber of seconds between transmitting OAM loopback cells.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.15 |
stnVcLinkOAMRetryUpCountNumber of consecutive end-to-end F5 OAM loopback cell responses that must be received in order to change a PVC state to up. Does not apply to SVCs.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.16 |
stnVcLinkOAMRetryDownCountNumber of consecutive end-to-end F5 OAM loopback cell responses that are not received in order to change a PVC state to down or tear down an SVC.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.17 |
stnVcLinkOAMRetryFrequencyThe frequency (in seconds) that end-to-end F5 loopback cells should be transmitted when a change in UP/DOWN state is being verified. For example, if a PVC is up and a loopback cell response is not received after the frequency (in seconds, then loopback cells are sent at the retry-frequency to verify whether or not the PVC is down.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.18 |
stnVcLinkPppIdPPP IDro Integer32 .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.19 |
stnVcLinkOperStatusOperational status of the VC Link.ro VcLinkOperStatus .1.3.6.1.4.1.3551.2.6.1.1.1.1.1.20 |
stnAtmCrossConns OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.2 |
stnVcCrossConns OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.2.1 |
stnVcCrossConnTableA list of VC cross connection entries. SEQUENCE OF StnVcCrossConnEntry .1.3.6.1.4.1.3551.2.6.1.2.1.1 |
stnVcCrossConnEntryEntry contains information about a particular VC cross connection. StnVcCrossConnEntry .1.3.6.1.4.1.3551.2.6.1.2.1.1.1 |
stnVcCrossConnLowIfIndexThe value of this object is equal to MIB II's ifIndex value of the ATM interface port for this VP cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.1 |
stnVcCrossConnLowVpiThe value of this object is equal to the VPI value at the ATM interface associated with the VP cross-connect that is identified by LowIfIndex. The VPI value cannot exceed the number supported by the atmInterfaceMaxVpiBits at the low ATM interface port.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.2 |
stnVcCrossConnLowVciThe value of this object is equal to the VCI value at the ATM interface associated with the VC cross-connect that is identified by LowIfIndex. The VCI value cannot exceed the number supported by the atmInterfaceMaxVciBits at the low ATM interface port.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.3 |
stnVcCrossConnHighIfIndexThe value of this object is equal to MIB II's ifIndex value of the ATM interface port for this VP cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.4 |
stnVcCrossConnHighVpiThe value of this object is equal to the VPI value at the ATM interface associated with the VP cross-connect that is identified by LowIfIndex. The VPI value cannot exceed the number supported by the atmInterfaceMaxVpiBits at the low ATM interface port.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.5 |
stnVcCrossConnHighVciThe value of this object is equal to the VCI value at the ATM interface associated with the VC cross-connect that is identified by LowIfIndex. The VCI value cannot exceed the number supported by the atmInterfaceMaxVciBits at the low ATM interface port.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.6 |
stnVcCrossConnLowAutoAssignControls low vpi/vci/ifIndex auto assignement to an ECF. If set to true MSM will attempt to dynamically auto assign the connection to an available ECF.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.7 |
stnVcCrossConnHighAutoAssignControls high vpi/vci/ifIndex auto assignement to an ECF. If set to true MSM will attempt to dynamically auto assign the connection to an available ECF.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.8 |
stnVcCrossConnOperStatusOperational status of the VC cross connection.ro VcCrossConnOperStatus .1.3.6.1.4.1.3551.2.6.1.2.1.1.1.9 |
stnVpCrossConns OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.2.2 |
stnAtmTrafficDescrs OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.3 |
stnTrafficDescrTableA list of ATM traffic descriptor entries. SEQUENCE OF StnTrafficDescrEntry .1.3.6.1.4.1.3551.2.6.1.3.1 |
stnTrafficDescrEntryEntry contains information about a particular ATM traffic descriptor. StnTrafficDescrEntry .1.3.6.1.4.1.3551.2.6.1.3.1.1 |
stnTrafDescrIndexThe value of this object identifies the row in the stnTrafficDescrTable.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.1 |
stnTrafDescrNameText name assigned to this traffic descriptor.ro OCTET STRING .1.3.6.1.4.1.3551.2.6.1.3.1.1.2 |
stnTrafDescrTypeThe value of this object identifies the type of ATM traffic descriptor. The type may indicate no traffic descriptor or traffic descriptor with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmTrafDescrParam1, atmTrafDescrParam2, atmTrafDescrParam3, atmTrafDescrParam4, atmTrafDescrParam5 Type values are as follows: no-td no-clp-no-scr clp-no-ag-no-scr clp-agging-no-scr no-clp-scr clp-no-tag-scr clp-tagging-scr clp-no-tag-mcr clp-trans-no-scr clp-trans-scr no-clp-tag-no-scrro Enumeration .1.3.6.1.4.1.3551.2.6.1.3.1.1.3 |
stnTrafDescrParam1The first parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.4 |
stnTrafDescrParam2The second parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.5 |
stnTrafDescrParam3The third parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.6 |
stnTrafDescrParam4The fourth parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.7 |
stnTrafDescrParam5The fifth parameter of the ATM traffic descriptor used according to the value of atmTrafDescrType.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.8 |
stnTrafDescrQosClassThe value of this object identifies the QoS Class. Four Service classes have been specified in the ATM Forum UNI Specification: Service Class A: Constant bit rate video and Circuit emulation. Service Class B: Variable bit rate video/audio. Service Class C: Connection-oriented data. Service Class D: Connectionless data. Four QoS classes numbered 1, 2, 3, and 4 have been specified with the aim to support service classes A, B, C, and D respectively. An unspecified QoS Class numbered '0' is used for best effort traffic.ro Enumeration .1.3.6.1.4.1.3551.2.6.1.3.1.1.9 |
stnTrafDescrServiceCategoryThe ATM service category. Service categories are as follows: other, cbr, rt-vbr, nrt-vbr, abr, ubrro Enumeration .1.3.6.1.4.1.3551.2.6.1.3.1.1.10 |
stnTrafDescrFrameDiscardWhether the network should discard frames rather than cells.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.3.1.1.11 |
stnTrafDescrOperStatusOperational status of the traffic descriptor.ro TrafficDescrOperStatus .1.3.6.1.4.1.3551.2.6.1.3.1.1.12 |
stnTrafDescrCommittedRateThe traffic rate in bits per second that the network is committed to transmit for VCs using this transmit traffic descriptor.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.13 |
stnTrafDescrMaximumRateThe maximum traffic rate in bits per second that the network will transmit for VCs using this transmit traffic descriptor, if it differs from the committed rate.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.3.1.1.14 |
stnAtmPorts OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4 |
stnAtmPortAttrs OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.1 |
stnAtmPortAttrTableA list of ATM port attribute entries. SEQUENCE OF StnAtmPortAttrEntry .1.3.6.1.4.1.3551.2.6.1.4.1.1 |
stnAtmPortAttrEntryEntry contains information about a particular ATM port attribute entry. StnAtmPortAttrEntry .1.3.6.1.4.1.3551.2.6.1.4.1.1.1 |
stnAtmPortIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.1 |
stnAtmPortIfTypeThe interface type of the connection point to the switch fabric. Values are: sonet(1), enet(2), epif(3), rim-enet(4).ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.2 |
stnAtmPortIfStateThe interface state of the connection point to the switch fabric. Values are: not-present(0), detected(1), configured(2), up-non-redundant(3), up-redundant(4), down-non-redundant(5), down-redundant(6), failed(7), initialized(8)ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.3 |
stnAtmPortEnabledWhether the ATM port is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.4 |
stnAtmPortMinVccVpiMinimum VPI used for Virtual Channel Circuits.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.5 |
stnAtmPortMaxVccVpiMaximum VPI used for Virtual Channel Circuits.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.6 |
stnAtmPortMinVccVciMinimum VCI used for Virtual Channel Circuits. To avoid clashes with the reserved ATM VCI values (such as 5 for signaling and any other reserved values including Connection Manager VCs), the recommended value is 32.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.7 |
stnAtmPortMaxVccVciMaximum VCI used for Virtual Channel Circuits.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.8 |
stnAtmPortMinVpcVpiMinimum VPI used for Virtual Path Circuits. To avoid clashes with the reserved ATM VCCs values (such as 5 for signaling and any other reserved values including Connection Manager VCs), the recommended value is 1.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.9 |
stnAtmPortMaxVpcVpiMaximum VCI used for Virtual Channel Circuits.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.10 |
stnAtmPortMaxActivePathsThe maximum number of active paths that can be active at any time on this port.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.11 |
stnAtmPortMaxActiveChannelsThe maximum number of virtual channels that can be active at any time on this port.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.12 |
stnAtmPortPVCAddressThe default configured PVC address information (20-byte NSAP address).ro NSAPAddress (SPRING-TIDE-NETWORKS-TC) .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.13 |
stnAtmPortSVCAddressThe default configured SVC address information (20-byte NSAP address).ro NSAPAddress (SPRING-TIDE-NETWORKS-TC) .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.14 |
stnAtmPortSigVpiThe VPI used for the signaling channel.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.15 |
stnAtmPortSigVciThe VCI used for the signaling channel.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.16 |
stnAtmPortSigEnabledIndicates if port will have a signaling stack.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.17 |
stnAtmPortIlmiVpiThe VPI used for ILMI channel.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.18 |
stnAtmPortIlmiVciThe VCI used for ILMI channel.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.19 |
stnAtmPortIlmiEnabledIndicates if port will use ILMI.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.20 |
stnAtmPortOamManagementEnabledIndicates if port is using OAM Management Procedures.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.21 |
stnAtmPortOamXmtFrequencyIndicates Frequency of OAM Transmit Cells.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.22 |
stnAtmPortOamRetryUpCountIndicates OAM Cell Retry Up Count value.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.23 |
stnAtmPortOamRetryDownCountIndicates OAM Cell Retry Down Count value.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.24 |
stnAtmPortOamRetryFrequencyIndicates OAM Retry Frequency value.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.25 |
stnAtmPortOperStatusOperational status of the Port.ro AtmPortOperStatus .1.3.6.1.4.1.3551.2.6.1.4.1.1.1.26 |
stnAtmPortIlmi OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.2 |
stnAtmPortIlmiTableA list of ATM ILMI Port entries. SEQUENCE OF StnAtmPortIlmiEntry .1.3.6.1.4.1.3551.2.6.1.4.2.1 |
stnAtmPortIlmiEntryEntry contains information about a particular ATM Port ILMI entry. StnAtmPortIlmiEntry .1.3.6.1.4.1.3551.2.6.1.4.2.1.1 |
stnAtmPortIlmiIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.1 |
stnAtmPortIlmiVersionSpecifies the signaling stack protocol type to be used on this port. Valid options are: uni-3-dot-0 uni-3-dot-1 uni-4-dot-0 iisp-3-dot-1ro Enumeration .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.2 |
stnAtmPortIlmiNetworkOrientationSpecifies the ATM device type. Valid options are: user, networkro Enumeration .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.3 |
stnAtmPortIlmiAutoNegotiateIndicates ILMI auto negotiation modero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.4 |
stnAtmPortIlmiPollIntervalILMI connection poll interval (S) in seconds. When DC-ILMI is transmitting SNMP Get messages during the attempt to establish connectivity with the remote ILMI component, this parameter determines the time in seconds between transmissions. The default value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1).ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.5 |
stnAtmPortIlmiCheckConnectionIntILMI check connection poll interval (T) in seconds. If connectivity checking is enabled (as spec by the value connect in the Admin_Status parameter below), this parameter specifies the time in seconds between successive transmissions of MIB Get msgs for the purpose of detecting loss of ILMI connectivity. If connectivity checking is not enabled, this parameter must be set to zero. The default value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1).ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.6 |
stnAtmPortIlmiInactivityFactorILMI inactivity factor (K). The number of consecutive polls for which no response is received from the remote ILMI component before ILMI connectivity is assumed to be lost. The dflt value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1).ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.7 |
stnAtmPortIlmiLocalConnSpecifies whether the local end of the ILMI connection is advertised as a 'public' or 'private' ILMI device. Values are: other, public, privatero Enumeration .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.8 |
stnAtmPortIlmiAdminStatusSpecifies which functions of DC-ILMI are enabled. The value std-ilmi must be specified; this value may be combined (using a bitwise OR) with one or more of the following values: std-ilmi - Standard ILMI functions are enabled. addr-reg - Address registration is enabled. connect - Connectivity chcking is enabled (DC-ILMI periodically sends a MIB Get request for the remote system's System ID, to ensure that it can still send and rcvd data on the ILMI connection). Default: (std-ilmi | addr-reg | connect)ro Bits .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.9 |
stnAtmPortIlmiEnterpriseEnterprise Object ID that DC-ILMI will use in building SNMP traps (or other generic MIB traps). This parameter can be used to identify the originator of the trap. The Object ID is specified as an array of unsigned long vals, as follows: The first entry in the array is the length of the array (the num of unsigned long values it contains, including the len value). The second entry in the array is an identifier specifying the Family type of the Object ID. This reps a prefix Object ID; the MIB Sub-Agent is responsible for matching this id with the dotted-decimal notation for this prefix. The remainder of the array gives the index part of the Object ID (the dotted-decimal notation from the end of the Family), with 1 unsigned long for each decimal number in this notation.ro OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.10 |
stnAtmPortIlmiLocalOidObject ID identifying the local machine - the first 4 octets indicate the length of the object id. For example, the null object id (0.0), which should be used if no object id is specified, is encoded as 3, 0, 0.ro OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.11 |
stnAtmPortIlmiNetPrefixDefault network prefix. If the prefix length is non-zero, ILMI creates an entry in the ILMI NetPrefix Table for this prefix; otherwise the Net_Prefix parameter is not used.ro OCTET STRING .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.12 |
stnAtmPortIlmiPrefixLenThe length of the default network prefixro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.2.1.1.13 |
stnAtmPortSignaling OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.3 |
stnAtmPortSigs OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.3.1 |
stnAtmPortSigTableA list of ATM port signal entries. SEQUENCE OF StnAtmPortSigEntry .1.3.6.1.4.1.3551.2.6.1.4.3.1.1 |
stnAtmPortSigEntryEntry contains information about a particular ATM port signal entry. StnAtmPortSigEntry .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1 |
stnAtmPortSigIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.1 |
stnAtmPortSigVersionSpecifies the signaling stack protocol type to be used on this port. Valid options are: UNI 3.0, UNI 3.1, IISP 3.1, PNNI 1.0ro Enumeration .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.2 |
stnAtmPortSigNetworkOrientationIndicates whether the ATM device is of the user or network type. Valid values are: user, networkro Enumeration .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.3 |
stnAtmPortSigAssignVpiVciSpecifies whether VPI/VCI assignment is the responsibility of the local signaling stack or of its partner stack. This parameter is used only for UNI 4.0. Values are: true - The local signaling stack is responsible for assigning VPIs/VCIs. false - The parent-signaling stack is responsible for assigning VPIs/VCIs. TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.4 |
stnAtmPortSigVpSigTypeSpecifies whether this signaling stack performs VP associated signaling: Valid options are: associated-signaling explicit-vpciro Enumeration .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.5 |
stnAtmPortSigParseModeSpecifies whether the message parser component of Sig should perform validity checking on the contents of received IEs. This element resides in the CCS MIB to allow software config of this behavior for compliance testing. Values are: normal - The parser checks the contents of the IEs the Sig uses and ensures that they are valid. For other IEs, it checks only the IE type and length and does not parse the contents. strict - The parser checks the contents of addit IEs as well as those used by Signaling and also checks for incorrect repetition of these add it IEs. Errors are handled in the same way as for the IEs used by sig (by sending a status message in UNI 3.1 or by following the IE instruction indicator in UNI 4.0).ro Enumeration .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.6 |
stnAtmPortSigPrefCarrierPresentSpecifies whether a default prefrd carrier (transit network) is defined. Valid options are: true - the Default_Network_Id below defines which carr is the preferred carrier. false - no default preferred carrier is defined.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.7 |
stnAtmPortSigPrefCarrierSpecifies the default preferred carrier. If stnAtmPortIlmiPrefCarrierPresent is set to false, this element is not used.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.3.1.1.1.8 |
stnAtmPortSigDurations OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.3.2 |
stnAtmPortSigDurationTableA list of ATM Port Signaling Duration entries. SEQUENCE OF StnAtmPortSigDurationEntry .1.3.6.1.4.1.3551.2.6.1.4.3.2.1 |
stnAtmPortSigDurationEntryEntry contains information about a particular ATM Port Signaling Duration entry. StnAtmPortSigDurationEntry .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1 |
stnAtmPortSigDurIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.1 |
stnAtmPortSigT301DurationT301 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.2 |
stnAtmPortSigT303DurationT303 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.3 |
stnAtmPortSigT306DurationT306 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.4 |
stnAtmPortSigT308DurationT308 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Intrface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.5 |
stnAtmPortSigT309DurationT309 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.6 |
stnAtmPortSigT310DurationT310 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.7 |
stnAtmPortSigT313DurationT313 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.8 |
stnAtmPortSigT316DurationT316 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.9 |
stnAtmPortSigT317DurationT317 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.10 |
stnAtmPortSigT322DurationT322 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.11 |
stnAtmPortSigT331DurationT331 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.12 |
stnAtmPortSigT333DurationT333 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.13 |
stnAtmPortSigT397DurationT397 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.14 |
stnAtmPortSigT398DurationT398 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.15 |
stnAtmPortSigT399DurationT399 timer. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.16 |
stnAtmPortSigSaalRetryDurationSAAL retry duration. See ITU-T Q.2931 B-ISDN DSS2 User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Controlro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.2.1.1.17 |
stnAtmPortSigRetries OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.3.3 |
stnAtmPortSigRetryTableA list of ATM Port Signaling retry entries. SEQUENCE OF StnAtmPortSigRetryEntry .1.3.6.1.4.1.3551.2.6.1.4.3.3.1 |
stnAtmPortSigRetryEntryEntry contains information about a ITU-T Q.2931 timer retry counters. StnAtmPortSigRetryEntry .1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1 |
stnAtmPortSigRetryIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.1 |
stnAtmPortSigT303RetriesThe number of ATM Port Signaling T303 retries.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.2 |
stnAtmPortSigT308RetriesThe number of ATM Port Signaling T308 retries.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.3 |
stnAtmPortSigT316RetriesThe number of ATM Port Signaling T316 retries.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.4 |
stnAtmPortSigT322RetriesThe number of ATM Port Signaling T322 retries.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.5 |
stnAtmPortSigT331RetriesThe number of ATM Port Signaling T331 retries.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.1.1.6 |
stnAtmPortSigSSCSTableA list of ATM Port Signaling SSCS entries. SEQUENCE OF StnAtmPortSigSSCSEntry .1.3.6.1.4.1.3551.2.6.1.4.3.3.2 |
stnAtmPortSigSSCSEntryEntry contains information about a particular Atm Port Signaling SSCS entry. StnAtmPortSigSSCSEntry .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1 |
stnAtmPortSigSSCSIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.1 |
stnAtmPortSigSSCSPollDurationThe duration of the SSCS Poll timer in milliseconds.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.2 |
stnAtmPortSigSSCSKeepAliveDurationThe duration of the SSCS keep-alive timer in milliseconds.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.3 |
stnAtmPortSigSSCSIdleDurationThe duration of the SSCS idle timer in milliseconds.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.4 |
stnAtmPortSigSSCSNoRspDurationThe duration of the SSCS no-response timer in milliseconds.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.5 |
stnAtmPortSigSSCSCcDurationThe duration of the SSCS CC timer in milliseconds.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.6 |
stnAtmPortSigSSCSMaxRcvWindowSizeThe maximum size on a receive window.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.7 |
stnAtmPortSigSSCSMaxCcRetriesThe maximum number of expiries and subsequent connection control PDU retransmissions acceptable before closing the connection.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.8 |
stnAtmPortSigSSCSMaxSdBetwPollsThe maximum number of STAT list elements in a STAT PDU.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.9 |
stnAtmPortSigSSCSMaxStatListElmsThe maximum number of STAT list elements in a STAT PDU.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.10 |
stnAtmPortSigSSCSPollAfterRetransWhether to send a POLL after retransmitting PDUs.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.11 |
stnAtmPortSigSSCSRepeatUstatQSAAL only: if true, send two USTATs each time a USTAT is sent.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.12 |
stnAtmPortSigSSCSUstatRspToPollQSAAL only: whether USTAT PDUs are issued in response to POLLs.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.4.3.3.2.1.13 |
stnAtmPortTraffic OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.4.4 |
stnAtmPortTrafficTableA list of ATM port traffic entries. SEQUENCE OF StnAtmPortTrafficEntry .1.3.6.1.4.1.3551.2.6.1.4.4.1 |
stnAtmPortTrafficEntryEntry contains information about a particular ATM port traffic entry. StnAtmPortTrafficEntry .1.3.6.1.4.1.3551.2.6.1.4.4.1.1 |
stnAtmPortTrafIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.4.4.1.1.1 |
stnAtmPortTrafTxCellsThe number of ATM cells transmitted.ro Counter32 .1.3.6.1.4.1.3551.2.6.1.4.4.1.1.2 |
stnAtmPortTrafRxCellsThe number of ATM cells received.ro Counter32 .1.3.6.1.4.1.3551.2.6.1.4.4.1.1.3 |
stnAtmPortTrafTxParityErrorsThe number of ATM transmit parity errors.ro Counter32 .1.3.6.1.4.1.3551.2.6.1.4.4.1.1.4 |
stnAtmPortTrafRxHdrChkSumErrorsThe number of received ATM header checksum errors.ro Counter32 .1.3.6.1.4.1.3551.2.6.1.4.4.1.1.5 |
stnAtmPortTrafPhyParityErrorsThe number of ATM physical parity errors.ro Counter32 .1.3.6.1.4.1.3551.2.6.1.4.4.1.1.6 |
stnAtmPortTrafCrc10ErrorsThe number of ATM CRC-10 errors.ro Counter32 .1.3.6.1.4.1.3551.2.6.1.4.4.1.1.7 |
stnAtmTraces OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.5 |
stnTraceIps OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.5.1 |
stnTraceIpsEnabledSpecifies whether IPS tracing is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.5.1.1 |
stnTraceIpsSizeSpecifies the maximum IPS trace buffer size multipled by 1024. The IPS trace log file will wrap when it reaches the maximum. Default: 1000 x 1024 Linesro Integer32 .1.3.6.1.4.1.3551.2.6.1.5.1.2 |
stnTraceIpsFileSpecifies the IPS output path and file name. Changes to the path or filename take effect when IPS tracing is disabled and restarted (close file and open new).ro OCTET STRING .1.3.6.1.4.1.3551.2.6.1.5.1.3 |
stnTracePd OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.5.2 |
stnTracePdProblemEnabledSpecifies whether PD problem tracing is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.5.2.1 |
stnTracePdExceptionEnabledSpecifies whether PD exception tracing is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.5.2.2 |
stnTracePdAuditEnabledSpecifies whether PD audit tracing is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.5.2.3 |
stnTracePdDeveloperEnabledSpecifies whether PD developer tracing is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.5.2.4 |
stnTracePdSizeSpecifies the maximum PD trace buffer size multipled by 1024. The PD trace log file will wrap when it reaches the maximum.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.5.2.5 |
stnTracePdFileSpecifies the IPS output path and file name. Changes to the path or filename take effect when IPS tracing is disabled and restarted.ro OCTET STRING .1.3.6.1.4.1.3551.2.6.1.5.2.6 |
stnAtmQos OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.6 |
stnQosCLR OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.6.1 |
stnQosClass1CLRQoS Class 1 cell loss ratio.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.1.1 |
stnQosClass2CLRQoS Class 2 cell loss ratio.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.1.2 |
stnQosClass3CLRQoS Class 3 cell loss ratio.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.1.3 |
stnQosClass4CLRQoS Class 4 cell loss ratio.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.1.4 |
stnQosCDV OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.6.2 |
stnQosClass1CDVQoS Class 1 cell delay variation.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.2.1 |
stnQosClass2CDVQoS Class 2 cell delay variation.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.2.2 |
stnQosClass3CDVQoS Class 3 cell delay variation.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.2.3 |
stnQosClass4CDVQoS Class 4 cell delay variation.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.2.4 |
stnQosCTD OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.6.3 |
stnQosClass1MaxCTDQoS Class 1 cell transfer delay.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.3.1 |
stnQosClass2MaxCTDQoS Class 2 cell transfer delay.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.3.2 |
stnQosClass3MaxCTDQoS Class 3 cell delay transfer.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.3.3 |
stnQosClass4MaxCTDQoS Class 4 cell delay transfer.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.6.3.4 |
stnAtmAddresses OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.7 |
stnAtmAddressTableA list of ATM address entries. SEQUENCE OF StnAtmAddressEntry .1.3.6.1.4.1.3551.2.6.1.7.1 |
stnAtmAddressEntryEntry contains information about a particular session. StnAtmAddressEntry .1.3.6.1.4.1.3551.2.6.1.7.1.1 |
stnAtmAddrIfIndexThe interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the slot and port of the module.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.3551.2.6.1.7.1.1.1 |
stnAtmAddrAddressThe value of the ATM NSAP address.ro NSAPAddress (SPRING-TIDE-NETWORKS-TC) .1.3.6.1.4.1.3551.2.6.1.7.1.1.2 |
stnAtmAddrAddressLenThe number of relevent bits in the ATM address.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.7.1.1.3 |
stnAtmThresholds OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.8 |
stnAtmThresholdTableA list of ATM threshold entries. SEQUENCE OF StnAtmThresholdEntry .1.3.6.1.4.1.3551.2.6.1.8.1 |
stnAtmThresholdEntryEntry contains information about a particular ATM threshold entry. StnAtmThresholdEntry .1.3.6.1.4.1.3551.2.6.1.8.1.1 |
stnAtmTholdTgrpIdSpecifies the threshold group indentifier.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.8.1.1.1 |
stnAtmTholdRegionIdRegion identifier within a threshold group.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.8.1.1.2 |
stnAtmTholdCellLowerLimitLower Cell number limit for region.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.8.1.1.3 |
stnAtmTholdCellUpperLimitUpper Cell number limit for region.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.8.1.1.4 |
stnAtmTholdCellQLimitMarkingQueue limit for any flow above which EFCI marking occurs.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.8.1.1.5 |
stnAtmTholdQLimitDiscardQueue limit for any flow above which Discard processing occurs.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.8.1.1.6 |
stnAtmTholdQueueLimitQueue limit for any flow above which cells are automatically discarded.ro INTEGER .1.3.6.1.4.1.3551.2.6.1.8.1.1.7 |
stnAtmAcct OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.1.9 |
stnAtmAcctEnabledSpecifies whether account logging is turned on or off.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3551.2.6.1.9.1 |
stnAtmAcctMaxSizeSpecifies the maximum accounting log buffer size. in Kbytes. The accounting log file will be closed when it reaches the maximum size and the name appended with a numeric differentiation.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.9.2 |
stnAtmAcctMaxFilesSpecifies the maximum number of history files to be stored. Once the maximum number of files is reached, the oldest file is deleted.ro Integer32 .1.3.6.1.4.1.3551.2.6.1.9.3 |
stnAtmAcctFilePathSpecifies the accounting log output path and file name on remote device.ro OCTET STRING .1.3.6.1.4.1.3551.2.6.1.9.4 |
stnAtmAcctFtpServer1The IP address of the first remote FTP server.ro IpAddress .1.3.6.1.4.1.3551.2.6.1.9.5 |
stnAtmAcctFtpUserName1The first FTP server username.ro DisplayString .1.3.6.1.4.1.3551.2.6.1.9.6 |
stnAtmAcctFtpPassword1The first FTP server password. OCTET STRING .1.3.6.1.4.1.3551.2.6.1.9.7 |
stnAtmAcctFtpServer2The IP address of the second remote FTP server.ro IpAddress .1.3.6.1.4.1.3551.2.6.1.9.8 |
stnAtmAcctFtpUserName2The second FTP server username.ro DisplayString .1.3.6.1.4.1.3551.2.6.1.9.9 |
stnAtmAcctFtpPassword2The second FTP server password. OCTET STRING .1.3.6.1.4.1.3551.2.6.1.9.10 |
stnAtmAcctFtpServer3The IP address of the third remote FTP server.ro IpAddress .1.3.6.1.4.1.3551.2.6.1.9.11 |
stnAtmAcctFtpUserName3The third FTP server username.ro DisplayString .1.3.6.1.4.1.3551.2.6.1.9.12 |
stnAtmAcctFtpPassword3The third FTP server password. OCTET STRING .1.3.6.1.4.1.3551.2.6.1.9.13 |
stnAtmAcctCurrentFtpServerThe IP address of the current FTP server.ro IpAddress .1.3.6.1.4.1.3551.2.6.1.9.14 |
stnAtmAcctPreviousFtpServerThe IP address of the previous FTP server.ro IpAddress .1.3.6.1.4.1.3551.2.6.1.9.15 |
stnAtmMibConformance OBJECT IDENTIFIER .1.3.6.1.4.1.3551.2.6.2 |
stnCdrServerFailureA stnCdrServerFailure trap signifies that the agent entity has detected that the accounting server has failed over to an auxilary server. The generation of this trap can be controlled by the stnNotificationEnableCdrServerFailure object in this MIB. NOTIFICATION-TYPE .1.3.6.1.4.1.3551.2.100.0.15 |
stnCdrLogFailureA stnCdrLogFailure trap signifies that the agent entity has detected that all accounting servers are inaccessible. Accounting data could be lost. The generation of this trap can be controlled by the stnNotificationEnableCdrLogFailure object in this MIB. NOTIFICATION-TYPE .1.3.6.1.4.1.3551.2.100.0.16 |
stnConfigAuditPvcFailureA stnConfigAuditPvcFailure trap signifies that the agent entity has detected an inconsistency between an active and configured PVC after a failover. The generation of this trap can be controlled by the CfgAuditPvcTraps configuration object. NOTIFICATION-TYPE .1.3.6.1.4.1.3551.2.100.0.31 |
stnConfigAuditSpvcFailureA stnConfigAuditSpvcFailure trap signifies that the agent entity has detected an inconsistency between an active and configured SPVC after a failover. The generation of this trap can be controlled by the CfgAuditSpvcTraps configuration object. NOTIFICATION-TYPE .1.3.6.1.4.1.3551.2.100.0.32 |