SCA-MPLINK2-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for SCA-MPLINK2-MIB.
71
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
71 total| Object Name |
|---|
mplk2 OBJECT IDENTIFIER .1.3.6.1.4.1.208.44 |
SCANET-MIB Unknown .1.3.6.1.4.1.208.44 |
mpl2LockEventLock state changed to <mpl2ServiceLock> for link <mpl2ServiceNumber>.
This trap is sent when an MP Link is locked or
unlocked from local management or via SNMP. TRAP-TYPE .1.3.6.1.4.1.208.44.0.1 |
mpl2WanRetriesEventMax. retries exceeded (<mpl2WanRetries>) for link <mpl2WanNumber>.
This trap is sent when an MP Link has had more
failed connect-attempts than allowed in the
configuration. TRAP-TYPE .1.3.6.1.4.1.208.44.0.2 |
mpl2WanActivityEventDaily Activity Limit has been reached. Link <mpl2WanNumber> locked.
This trap is sent when the Daily Activity
Limit has been reached and locked the link. TRAP-TYPE .1.3.6.1.4.1.208.44.0.3 |
mpl2WanTimerEventLink timer has changed lock state to <WanTimer> for link <WanNumber>.
This trap is sent when an MP Link timer has
locked or unlocked the link. TRAP-TYPE .1.3.6.1.4.1.208.44.0.4 |
mpl2Service OBJECT IDENTIFIER .1.3.6.1.4.1.208.44.1 |
mpl2ServiceTableThis table contains information on MP Links.
These entries applies to LAN entries as well as
WAN entries. SEQUENCE OF Mpl2ServiceEntry .1.3.6.1.4.1.208.44.1.1 |
mpl2ServiceEntryInformation on a particular MP Link. Mpl2ServiceEntry .1.3.6.1.4.1.208.44.1.1.1 |
mpl2ServiceNumberThe MP Link number. The MP Link number is the
same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.44.1.1.1.1 |
mpl2ServiceSlotNumberThe Slot position of the card. Set to 0 for
stand-alone products.ro INTEGER .1.3.6.1.4.1.208.44.1.1.1.2 |
mpl2ServicePlugNumberThe plug number of the physical interface to
which the MP Link is associated.ro INTEGER .1.3.6.1.4.1.208.44.1.1.1.3 |
mpl2ServicePlugNameThe name of the physical interface to which
the MP Link is associated.ro DisplayString .1.3.6.1.4.1.208.44.1.1.1.4 |
mpl2ServiceAttachmentThe connector type used to connect the router
to the LAN or WAN.ro Attachment .1.3.6.1.4.1.208.44.1.1.1.5 |
mpl2ServiceProviderThe type of provider for this MP Link. For WAN
links this specifies the actual protocol
stack.ro Enumeration .1.3.6.1.4.1.208.44.1.1.1.6 |
mpl2ServiceBytesSentUpperThe upper 32 bits of the 64 bits counter which
is the number of octets (bytes) sent via the MP
Link.ro Counter .1.3.6.1.4.1.208.44.1.1.1.7 |
mpl2ServiceBytesSentLowerThe lower 32 bits of the 64 bits counter which
is the number of octets (bytes) sent via the MP
Link.ro Counter .1.3.6.1.4.1.208.44.1.1.1.8 |
mpl2ServiceBytesReceivedUpperThe lower 32 bits of the 64 bits counter which
is the number of octets (bytes) sent via the MP
Link.ro Counter .1.3.6.1.4.1.208.44.1.1.1.9 |
mpl2ServiceBytesReceivedLowerThe lower 32 bits of the 64 bits counter which
is the number of octets (bytes) received via
the MP Link.ro Counter .1.3.6.1.4.1.208.44.1.1.1.10 |
mpl2ServiceLockIndicates whether an MP Link has been locked
from local management. The link may be unlocked
by setting the value to 'off' and locked by
setting the value to 'on'.rw OnOff .1.3.6.1.4.1.208.44.1.1.1.11 |
mpl2LanSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.208.44.2 |
mpl2LanTableThis table contains information on LAN MP
Links. SEQUENCE OF Mpl2LanEntry .1.3.6.1.4.1.208.44.2.1 |
mpl2LanEntryInformation on a particular LAN MP Link. Mpl2LanEntry .1.3.6.1.4.1.208.44.2.1.1 |
mpl2LanNumberThe LAN MP Link number. The MP Link number is
the same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.44.2.1.1.1 |
mpl2LanRxCRCErrorsThe number of frames received which were
discarded due to Cyclic Redundancy Check (CRC)
errors.ro Counter .1.3.6.1.4.1.208.44.2.1.1.2 |
mpl2LanRxOverrunThe number of frames received which were lost
due to RAM overloads within the router. This
should not occur.ro Counter .1.3.6.1.4.1.208.44.2.1.1.3 |
mpl2LanRxLongThe number of frames received which were
discarded due to being larger than the maximum
allowable length on the LAN.ro Counter .1.3.6.1.4.1.208.44.2.1.1.4 |
mpl2LanRxOverflowThe number of frames received which were
discarded due to lack of buffer capacity.ro Counter .1.3.6.1.4.1.208.44.2.1.1.5 |
mpl2LanRxAlnErrorsThe number of frames received which were
discarded due to having the wrong frame
length.ro Counter .1.3.6.1.4.1.208.44.2.1.1.6 |
mpl2LanRxOutsThe number of frames received which were
processed by higher layer protocols.ro Counter .1.3.6.1.4.1.208.44.2.1.1.7 |
mpl2LanRxShortThe number of frames received which were
discarded due to being shorter than the smallest
allowable length on the LAN.ro Counter .1.3.6.1.4.1.208.44.2.1.1.8 |
mpl2LanTxDeferredThe number of outgoing frames which were
discarded due to a busy link.ro Counter .1.3.6.1.4.1.208.44.2.1.1.9 |
mpl2LanTxUnderrunThe number of outgoing frames which were
discarded due to overload.ro Counter .1.3.6.1.4.1.208.44.2.1.1.10 |
mpl2LanTxSQEFailureThe number of outbound frames which had
Signal Quality Errors (SQE).ro Counter .1.3.6.1.4.1.208.44.2.1.1.11 |
mpl2LanTxExcDeferralThe number of transmission attempts which were delayed
for more than 3.2 ms.ro Counter .1.3.6.1.4.1.208.44.2.1.1.12 |
mpl2LanTxCollExceedThe number of outbound frames which were
discarded due to exceeding 16 collisions on the
Ethernet.ro Counter .1.3.6.1.4.1.208.44.2.1.1.13 |
mpl2LanTxLateCollThe number of collisions occurring after the
first 512 bytes of a frame had been
transmitted.ro Counter .1.3.6.1.4.1.208.44.2.1.1.14 |
mpl2LanTxCollisionsThe number of outgoing frames which were
discarded due to collisions that occurred
during transmissions.ro Counter .1.3.6.1.4.1.208.44.2.1.1.15 |
mpl2LanTxNoCarrierThe number of No Carrier detections during
transmissions.ro Counter .1.3.6.1.4.1.208.44.2.1.1.16 |
mpl2WanSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.208.44.3 |
mpl2WanTableThis table contains information on WAN MP
Links. SEQUENCE OF Mpl2WanEntry .1.3.6.1.4.1.208.44.3.1 |
mpl2WanEntryInformation on a particular WAN MP Link. Mpl2WanEntry .1.3.6.1.4.1.208.44.3.1.1 |
mpl2WanNumberThe WAN MP Link number. The MP Link number is
the same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.44.3.1.1.1 |
mpl2WanDataStateThe state of the MP Link seen from the higher
layer protocol.ro DataState .1.3.6.1.4.1.208.44.3.1.1.2 |
mpl2WanDataStateTimerThe time in seconds since the MP Link entered
the Data State.ro INTEGER .1.3.6.1.4.1.208.44.3.1.1.3 |
mpl2WanConnectStateIndicates the connection state of the WAN MP
Link.ro ConnectState .1.3.6.1.4.1.208.44.3.1.1.4 |
mpl2WanConnectStateTimerThe time in seconds since the MP Link entered
the Connect State.ro INTEGER .1.3.6.1.4.1.208.44.3.1.1.5 |
mpl2WanCompressionIndicates if data compression is used over the
WAN MP Link. For frame relay links compression
is not negotiated. For all other WAN protocols
the compression will remain 'off' if not
configured in both routers over the link.ro OnOff .1.3.6.1.4.1.208.44.3.1.1.6 |
mpl2WanCompressionTypeProprietary compression is used for LAPB and
X.25 MP Links. For all other WAN protocols the
Stac compression algorithm is used.ro CompType .1.3.6.1.4.1.208.44.3.1.1.7 |
mpl2WanCallsSucceededThe number of outgoing call which succeeded in
making the connection.ro Counter .1.3.6.1.4.1.208.44.3.1.1.8 |
mpl2WanCallsFailedThe number of outgoing call which failed to
make the connection.ro Counter .1.3.6.1.4.1.208.44.3.1.1.9 |
mpl2WanCallsAcceptedThe number of incoming calls which were
accepted on this link.ro Counter .1.3.6.1.4.1.208.44.3.1.1.10 |
mpl2WanCallsRejectedThe number of incoming calls which were
rejected on this link.ro Counter .1.3.6.1.4.1.208.44.3.1.1.11 |
mpl2WanRetriesThe number of retries made for outgoing
calls. May be set to zero which causes the
call sequence to restarted.rw INTEGER .1.3.6.1.4.1.208.44.3.1.1.12 |
mpl2WanDirectionShows who initiated the call. 'incoming' if the
call was initiated by the remote router and
'outgoing' if the call was inititated by this
router. For PPP Multi Links the direction
refers the the direction of the first slave
link.ro Direction .1.3.6.1.4.1.208.44.3.1.1.13 |
mpl2WanHasBackupIndicates whether this link has a backup link
configured for it.ro OnOff .1.3.6.1.4.1.208.44.3.1.1.14 |
mpl2WanBackupForShows the primary link for which this link is
the backup. The value 0 indicates that this is
not a backup link.ro INTEGER .1.3.6.1.4.1.208.44.3.1.1.15 |
mpl2WanBackupForAttachmentIndicates whether this link is a backup for an
attachment.ro OnOff .1.3.6.1.4.1.208.44.3.1.1.16 |
mpl2WanIsSlaveIndicates whether this link is a slave link
associated with a PPP Multi Link.ro OnOff .1.3.6.1.4.1.208.44.3.1.1.17 |
mpl2WanPppMasterIndicates the master link for a slave link.
For master links and links not associated with
a PPP Multi Link the value is 0.ro INTEGER .1.3.6.1.4.1.208.44.3.1.1.18 |
mpl2WanPppSlaveUpCountThe number of slave links in Connect State
'up'. For slave links and links not associated
with a PPP Multi Link the value is 1.ro INTEGER .1.3.6.1.4.1.208.44.3.1.1.19 |
mpl2WanActivityTimeLeftThe time remaining in seconds until the Daily
Activity Limit will close and lock the link.
When the Daily Activity Limit has been reached,
the link can be activated by setting
mpl2WanActivity to 'on'.ro INTEGER .1.3.6.1.4.1.208.44.3.1.1.20 |
mpl2WanActivityIndicates whether the Daily Activity Limit has
been reached and locked the link. To unlock the
link set the value to 'off'. It is not possible
to set to the value to 'on'.rw OnOff .1.3.6.1.4.1.208.44.3.1.1.21 |
mpl2WanTimerIndicates whether an MP Link timer has locked
the link. 'on' means the link is locked.ro OnOff .1.3.6.1.4.1.208.44.3.1.1.22 |
mpl2IfSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.208.44.4 |
mpl2IfStackTableThis table contains information on the relationships
between the multiple sub-layers of network interfaces.
In particular, it contains information on which sub-
layers run 'on top of' which other sub-layers. Each
sub-layer corresponds to a conceptual row in the
ifTable. SEQUENCE OF Mpl2IfStackEntry .1.3.6.1.4.1.208.44.4.1 |
mpl2IfStackEntryInformation on a particular relationship between two
sub-layers, specifying that one sub-layer runs on
'top' of the other sub-layer. Each sub-layer
corresponds to a conceptual row in the ifTable. Mpl2IfStackEntry .1.3.6.1.4.1.208.44.4.1.1 |
mpl2IfStackNumberThe MP Link number. The MP Link number is the
same as the ifIndex for the corresponding
upper group in the MIB-2 ifGroup.ro INTEGER .1.3.6.1.4.1.208.44.4.1.1.1 |
mpl2IfStackLowerLayerThe value of ifIndex corresponding to the lower sub-
layer of the relationship, i.e., the sub-layer which
runs 'below' the sub-layer identified by the
corresponding instance of mpl2IfStackNumber. If
there is no lower sub-layer, then this object has the
value 0.ro INTEGER .1.3.6.1.4.1.208.44.4.1.1.2 |
mpl2General OBJECT IDENTIFIER .1.3.6.1.4.1.208.44.5 |
mpl2GeneralOverviewChangeThe value of sysUpTime at the time any MP Link
seen from the overview changed state or the
like.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.208.44.5.1 |