SCA-BOX-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for SCA-BOX-MIB.
71
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
71 total| Object Name |
|---|
box OBJECT IDENTIFIER .1.3.6.1.4.1.208.3 |
SCANET-MIB Unknown .1.3.6.1.4.1.208.3 |
boxPowerFailureEventThis trap is sent when a power supply failure has been
detected.
The variable indicates the failing power supply. TRAP-TYPE .1.3.6.1.4.1.208.3.0.1 |
boxFanFailureEventThis trap is sent when a fan failure has been detected. TRAP-TYPE .1.3.6.1.4.1.208.3.0.2 |
boxTempFailureEventThis trap is sent when a temperature sensor has
detected excessive temperature in the enclosure. TRAP-TYPE .1.3.6.1.4.1.208.3.0.3 |
boxModuleInsertedEventThis trap is sent when a module is inserted in the
the enclosure.
The variable slotmapFail indicates in which slot
a module is inserted TRAP-TYPE .1.3.6.1.4.1.208.3.0.4 |
boxModuleRemovedEventThis trap is sent when a module is removed in the
the enclosure.
The variable slotmapFail indicates in which slot
a module is removed TRAP-TYPE .1.3.6.1.4.1.208.3.0.5 |
enclosure OBJECT IDENTIFIER .1.3.6.1.4.1.208.3.1 |
ledts-xxxx
0 : red
off(0),red(1)
1 : green
off(0),green(2)
cs-xxxx
0 : fault
off(0),red(1)
1 : master
off(0),green(2)
2 : test1
off(0),yellow(4)
3 : test2
off(0),yellow(4)
4 : test3
off(0),yellow(4)
5 : test4
off(0),yellow(4)
6 : rx/tx
off(0),green(2)
se-xxxx
0 : fault
off(0),red(1)
1 : power
off(0),green(2)
2 : status1
off(0),red(1),green(2),yellow(4)
3 : status2
off(0),red(1),green(2),yellow(4)
4 : status3
off(0),red(1),green(2),yellow(4)
5 : status4
off(0),red(1),green(2),yellow(4)
6 : status5
off(0),red(1),green(2),yellow(4)
Note. Lower 3 bits indicates off/color (off(0),red(1),
green(2),yellow(4)), Higher 5 bits reserved for
flash frequency.ro OCTET STRING -- .1.3.6.1.4.1.208.3.1.1 |
fanIf this object returns 1 then a Fan has failed.ro Enumeration .1.3.6.1.4.1.208.3.1.2 |
powerIf this object returns a non-zero value then one
or more power supplies have failed.ro Enumeration .1.3.6.1.4.1.208.3.1.3 |
slotsThe number of slots in the enclosure.ro Enumeration .1.3.6.1.4.1.208.3.1.4 |
slotmapA bitmap of the slots in which a card is present.
Setting bit0 to 1 indicates that a card is present
in slot 1, and so on.ro OCTET STRING .1.3.6.1.4.1.208.3.1.5 |
temperatureIf this object returns 1 then a temperature sensor
has detected an excessive temperature in the enclosure.ro Enumeration .1.3.6.1.4.1.208.3.1.6 |
fanNoTotal number of fans supported.ro INTEGER .1.3.6.1.4.1.208.3.1.7 |
powerNoTotal number of power supplies supported.ro INTEGER .1.3.6.1.4.1.208.3.1.8 |
temperatureNoA return value of 1 indicates that temperature sensors
are supported in the enclosure.ro Enumeration .1.3.6.1.4.1.208.3.1.9 |
fanPresentA bitmask of the fans that are present.
Bit0 refers to fan 1, bit 1 to fan 2, etc.ro INTEGER .1.3.6.1.4.1.208.3.1.10 |
powerPresentA bitmask of the power supples that are present.
Bit0 refers to power supply 1, bit 1 to power supply 2, etc.ro INTEGER .1.3.6.1.4.1.208.3.1.11 |
temperaturePresentA return value of 1 indicates that temperature sensors
are present in the enclosure.ro Enumeration .1.3.6.1.4.1.208.3.1.12 |
psuFailThis object returns a non-zero value in a trap
according to the power supply number when a
power supply have failed. Enumeration .1.3.6.1.4.1.208.3.1.13 |
slotmapFailThis object returns a non-zero value in a trap
according to the slot number when a card
is enabled or disabled in the system center INTEGER -- slot number .1.3.6.1.4.1.208.3.1.14 |
boards OBJECT IDENTIFIER .1.3.6.1.4.1.208.3.2 |
brdInfoTable SEQUENCE OF BrdInfoEntry .1.3.6.1.4.1.208.3.2.1 |
brdInfoEntryInfo from 32 bytes standard memory area. BrdInfoEntry .1.3.6.1.4.1.208.3.2.1.1 |
brdNumber1Board Sequence number in enclosure (= slot number)ro INTEGER .1.3.6.1.4.1.208.3.2.1.1.1 |
cardTypeUnique 16 bit card type
This ID is used for unique sw identification of the card.
The list of possible return values is company private.ro INTEGER .1.3.6.1.4.1.208.3.2.1.1.2 |
pcbRevisionPCB Revision numberro INTEGER .1.3.6.1.4.1.208.3.2.1.1.3 |
macAddressThe Base MAC-Address allocated for MAC Interfaces
on the board.ro OCTET STRING -- .1.3.6.1.4.1.208.3.2.1.1.4 |
driverSeqRequired driver sequence number (SW)ro INTEGER .1.3.6.1.4.1.208.3.2.1.1.5 |
productProduct Identification.ro DisplayString .1.3.6.1.4.1.208.3.2.1.1.6 |
serialNumberProduction serial numberro OCTET STRING .1.3.6.1.4.1.208.3.2.1.1.7 |
masterSlaveThe board backplane bus properties.ro INTEGER .1.3.6.1.4.1.208.3.2.1.1.8 |
ramro INTEGER .1.3.6.1.4.1.208.3.2.1.1.9 |
shramro INTEGER .1.3.6.1.4.1.208.3.2.1.1.10 |
epromro INTEGER .1.3.6.1.4.1.208.3.2.1.1.11 |
e2promro INTEGER .1.3.6.1.4.1.208.3.2.1.1.12 |
flashpromro INTEGER .1.3.6.1.4.1.208.3.2.1.1.13 |
spec0Specific board info
The purpose of this BYTE is to indicate special
board hw-options. The definition of this byte
is board specific.
A System Center product with relevant information
in this byte have a specifiation in the product
manual's.ro OCTET STRING -- .1.3.6.1.4.1.208.3.2.1.1.14 |
spec1Specific board info
The purpose of this BYTE is to indicate special
board hw-options. The definition of this byte
is board specific.
A System Center product with relevant information
in this byte have a specifiation in the product
manual's.ro OCTET STRING -- .1.3.6.1.4.1.208.3.2.1.1.15 |
spec2Specific board info
The purpose of this BYTE is to indicate special
board hw-options. The definition of this byte
is board specific.
A System Center product with relevant information
in this byte have a specifiation in the product
manual's.ro OCTET STRING -- .1.3.6.1.4.1.208.3.2.1.1.16 |
spec3Specific board info
The purpose of this BYTE is to indicate special
board hw-options. The definition of this byte
is board specific.
A System Center product with relevant information
in this byte have a specifiation in the product
manual's.ro OCTET STRING -- .1.3.6.1.4.1.208.3.2.1.1.17 |
ipAddrIP Address to Manage Board in this slotro IpAddress .1.3.6.1.4.1.208.3.2.1.1.18 |
nsapNSAP to Manage Board in this slotro OCTET STRING -- .1.3.6.1.4.1.208.3.2.1.1.19 |
brdStatusTable SEQUENCE OF BrdStatusEntry .1.3.6.1.4.1.208.3.2.2 |
brdStatusEntryStatus information from boards. BrdStatusEntry .1.3.6.1.4.1.208.3.2.2.1 |
brdNumber2Board Sequence number in enclosure (= slot number)ro INTEGER .1.3.6.1.4.1.208.3.2.2.1.1 |
brdStatusBoard Status byte.
bit0 - reserved
bit1 Card Failed
bit2 - reserved
bit3 - reserved
bit4 Red component of Status LED (active low)
bit5 Green component of Status LED (active low)
bit6 - reserved
bit7 - reservedro INTEGER .1.3.6.1.4.1.208.3.2.2.1.2 |
brdLedDepends on the card type.
Note. Lower 3 bits indicates off/color (off(0),red(1),
green(2),yellow(4)), Higher 5 bits reserved for
flash frequency.ro OCTET STRING -- .1.3.6.1.4.1.208.3.2.2.1.3 |
brdPlugTableTable of plugs (and the possibly attached pims) on the board SEQUENCE OF BrdPlugEntry .1.3.6.1.4.1.208.3.2.3 |
brdPlugEntryInformation about plugs on boards. BrdPlugEntry .1.3.6.1.4.1.208.3.2.3.1 |
brdNumber3Board Sequence number in enclosure (= slot number)ro INTEGER .1.3.6.1.4.1.208.3.2.3.1.1 |
brdPlugNumberPlug Number - used to index plugs on board.ro INTEGER .1.3.6.1.4.1.208.3.2.3.1.2 |
brdPlugPositionPosition/name of plug on board.ro OCTET STRING .1.3.6.1.4.1.208.3.2.3.1.3 |
brdPlugStatusAvailability of plug on this hardware revisionro Enumeration .1.3.6.1.4.1.208.3.2.3.1.4 |
brdPlugTypeType of plugro OCTET STRING .1.3.6.1.4.1.208.3.2.3.1.5 |
brdPlugPimTypeType of pim inserted in plugro OCTET STRING .1.3.6.1.4.1.208.3.2.3.1.6 |
brdPlugPimLedsStatus of LEDs on pim in plugro OCTET STRING .1.3.6.1.4.1.208.3.2.3.1.7 |
brdPlugPimOptionsTextual description of any options installed
on pim in plugro OCTET STRING .1.3.6.1.4.1.208.3.2.3.1.8 |
brdOptionTableTable of various possible board options.
Options might be sub-boards or other kinds of hardware options. SEQUENCE OF BrdOptionEntry .1.3.6.1.4.1.208.3.2.4 |
brdOptionEntryInformation about board options. BrdOptionEntry .1.3.6.1.4.1.208.3.2.4.1 |
brdNumber4Board Sequence number in enclosure (= slot number)ro INTEGER .1.3.6.1.4.1.208.3.2.4.1.1 |
brdOptionNumberOption Number - used to index options on board.
If options is visible on front panel, they must
be sorted (top-most/left-most first).ro INTEGER .1.3.6.1.4.1.208.3.2.4.1.2 |
brdOptionNameDescriptive Name of option.ro OCTET STRING .1.3.6.1.4.1.208.3.2.4.1.3 |
brdOptionStateIs the option installed ?ro Enumeration .1.3.6.1.4.1.208.3.2.4.1.4 |
brdSwitchSettingTableTable of switch settings on the board. SEQUENCE OF BrdSwitchSettingEntry .1.3.6.1.4.1.208.3.2.5 |
brdSwitchSettingEntryInformation about Switch Setting BrdSwitchSettingEntry .1.3.6.1.4.1.208.3.2.5.1 |
brdNumber5Board Sequence number in enclosure (= slot number)ro INTEGER .1.3.6.1.4.1.208.3.2.5.1.1 |
brdSwitchNumberSwitch Number - used to index switches on board.ro INTEGER .1.3.6.1.4.1.208.3.2.5.1.2 |
brdSwitchNameDescriptive Name - used to identify switch on board.ro OCTET STRING .1.3.6.1.4.1.208.3.2.5.1.3 |
brdSwitchSettingDescriptive Name - used to describe switch setting on board.
Eg. 'On', 'Off', 'Enabled', 'Disabled', '0', '01001100',
'A', 'B', 'C', 'Open', 'Closed', 'Inserted',
'Not inserted', etc.ro OCTET STRING .1.3.6.1.4.1.208.3.2.5.1.4 |