SALIX-DS0-MIB
The SALIX-DS0-MIB enables monitoring and management of DS0 channel status, configuration, and performance counters on Salix Networks hardware. It provides vendor-specific access to digital signal level 0 interface metrics for troubleshooting and provisioning T1/E1 circuits.
Imported Objects
Objects
18 total| Object Name |
|---|
salixDsx0MIBThe MIB describing SALIX specific DS0 objects MODULE-IDENTITY .1.3.6.1.4.1.2158.5.1.4 |
salixDsx0MIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2158.5.1.4.1 |
salixDsx0CrossConnectTableThe table that describes the active DS0 Cross Connections
on the system. There should be one entry for each active
Cross Connect on the system. SEQUENCE OF SalixDsx0CrossConnectEntry .1.3.6.1.4.1.2158.5.1.4.1.1 |
salixDsx0CrossConnectEntryAn entry in the ITX DS0 cross connect table. This entry
describes the status of the DS0 cross connect, and also
provides information describing the cross connect SalixDsx0CrossConnectEntry .1.3.6.1.4.1.2158.5.1.4.1.1.1 |
salixDsx0CrossConnectHighInterfaceThe high ifIndex for identifying the cross connect.
Identifies the DS0 Channel involved in the cross connect.
The salixDsx0CrossConnectHighInterface value should be
higher than the salixDsx0CrossConnectLowInterface value InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2158.5.1.4.1.1.1.1 |
salixDsx0CrossConnectLowInterfaceThe low ifIndex for identifying the cross connect.
Identifies the DS0 Channel involved in the cross connect.
The salixDsx0CrossConnectLowInterface value should be
lower than the salixDsx0CrossConnectHighInterface value InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2158.5.1.4.1.1.1.2 |
salixDsx0CrossConnectDirectionThis attribute describes the direction of traffic flow the
DS0 cross connect.
high2low(1) - Traffic flows from the high interface
to the low interface in the cross
connect
low2high(2) - Traffic flows from the low interface
to the high interface in the cross
connect
bidirectional(3) - Traffic flows both directions through
the cross connectro Enumeration .1.3.6.1.4.1.2158.5.1.4.1.1.1.3 |
salixDsx0CrossConnectOperStatusThis attribute indicates the operational state of the
DS0 cross connection.
up(1) - The cross connect is up and active
down(2) - The cross connect is down and no
traffic is passing
unknown(3) - The status of the cross connect is
not knowro Enumeration .1.3.6.1.4.1.2158.5.1.4.1.1.1.4 |
salixDsx0CrossConnectStartTimeThe time at which the cross connect was createdro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.2158.5.1.4.1.1.1.5 |
salixDsx0CrossConnectRowStatusThe status of this entry in the salixDsx0CrossConnectTable.
This object is used to delete a salixDsx0CrossConnectTable
entry.
To destroy a cross connect, set this value to destory(6)
Row status values:
active(1) - set by the agent after this entry is created
notInService(2) - not applicable
notReady(3) - not applicable
createAndGo(4) - not applicable
createAndWait(5)- not applicable
destroy(6) - set by the management entity to destroy entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2158.5.1.4.1.1.1.6 |
salixDsx0ConfigTableThe DS0 Configuration table. Augments the DS0 Configuration table
from the DS0-MIB. There is an entry in this table for each DS0
interface. SEQUENCE OF SalixDsx0ConfigEntry .1.3.6.1.4.1.2158.5.1.4.1.2 |
salixDsx0ConfigEntryAn augmented entry in the DS0 Configuration table. There
is an entry in this table for each DS0 interface. SalixDsx0ConfigEntry .1.3.6.1.4.1.2158.5.1.4.1.2.1 |
salixDsx0StatusIndicated the status of the given DS0
notused(1) - The DS0 is not currently being used
crossconnect(2) - The DS0 is currently cross connected
rtpconnect(3) - The DS0 is currently connect to an
RTP session
loopback(4) - The DS0 is currently being looped back
test(5) - The DS0 is currently being continuity
tested
unknown(6) - The status of the DS0 is not knownro Enumeration .1.3.6.1.4.1.2158.5.1.4.1.2.1.1 |
salixDsx0MIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2158.5.1.4.2 |
salixDsx0MIBTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2158.5.1.4.2.0 |
salixDsx0MIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.2158.5.1.4.3 |
salixDsx0Groups OBJECT IDENTIFIER .1.3.6.1.4.1.2158.5.1.4.3.1 |
salixDsx0Compliances OBJECT IDENTIFIER .1.3.6.1.4.1.2158.5.1.4.3.2 |
More MIBs from SALIX
Browse all SALIXMIBs →The SALIX-HNE-MIB provides vendor-specific SNMP extensions for Salix HNE appliances, enabling the monitoring of proprietary hardware states, interface statistics, and system resource utilization not covered by standard MIBs. This module facilitates granular visibility into device health and performance metrics specific to the Salix HNE platform's enterprise networking functions.
SNMP MIB module
The SALIX-SYSTEM-MIB provides SNMP access to error reporting counters and core system status variables for Salix Networks appliances, enabling the monitoring of device health, fault conditions, and operational state metrics.
The SALIX-MGMCP-MIB module provides SNMP visibility into Salix MGMCP (Media Gateway Control Protocol) session states, enabling the monitoring of active call sessions, gateway registration status, and protocol negotiation metrics for media gateway controllers.
The SALIX-INSTALLED-SOFTWARE-MIB exposes SNMP-accessible objects to enumerate and track the specific software packages and their version states installed on SALIX network appliances. This module enables automated inventory auditing and compliance verification by providing granular visibility into the device's software composition.
The SALIX-M4-MIB module extends the standard M4-MIB to monitor and manage specific SALIX networking hardware metrics, including interface statistics, system resources, and device status. This vendor-specific extension enables precise telemetry collection for SALIX M4-series devices within SNMP-managed environments.