SAF-IPRADIO
AI MIB Summary
Standard SNMP MIB module defining data structures for SAF-IPRADIO.
145
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
145 total| Object Name |
|---|
saf OBJECT IDENTIFIER .1.3.6.1.4.1.7571 |
RFC1155-SMI Unknown .1.3.6.1.4.1.7571 |
tehnika OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100 |
microwaveRadio OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1 |
pointToPoint OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1 |
safip OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5 |
ipRadio OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1 |
ipRadioCfg OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1.1 |
ipRadioCfgGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1 |
productName of the model.ro DisplayString .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.1 |
descriptionDescription of the model.ro DisplayString .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.2 |
hostnameThe name of the host.rw DisplayString .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.3 |
sysDateAndTimeCurrent date and time set.
For SET tenths of seconds ignored.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.4 |
sysTemperatureUnit temperature in degrees by Celsius.
NB - sw before 2009.03.18 shows in *10 degreesro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.5 |
licenseTo set license information. Read allways 'OK'.rw DisplayString .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.6 |
licenseMaskRead license mask.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.7 |
licenseUpdateStatusStatus of last license update operation
by setting license using snmp.ro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.8 |
radioTableRadio table. SEQUENCE OF RadioEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10 |
radioEntryEntry containing objects in radio table. RadioEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1 |
radioIndexA unique value for each radio.
Its value represents UNIT:
1 - for 'local';
2 - for 'remote'ro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.1 |
radioGenStatusA General status of each radio:
1 - 'OK';
2 - 'error'ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.2 |
radioSideSide for duplex communication.rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.3 |
radioTxPowerTx power of radio transmitter in dBm.rw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.4 |
radioRxLevelReceived signal level in dBm.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.5 |
radioDuplexShiftUtilized duplex shift in KHz.rw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.6 |
radioLoopbackRadio loopback on/off. To set use
loopback command.ro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.7 |
radioTxMuteStatus of 'Tx mute':
1 - Tx is muted;
2 - Tx is not muted.rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.8 |
radioTxFrequencyTx frequency in kHz.rw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.9 |
radioRxFrequencyRx frequency in kHz.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.10.1.10 |
aTPCTableATPC table SEQUENCE OF ATPCEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.11 |
aTPCEntryEntry containing objects in ATPC table. ATPCEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.11.1 |
atpcIndexIts value represents UNIT
1 for 'local';
2 for 'remote'.ro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.11.1.1 |
atpcEnabledATPC status:
1 for 'on';
2 for 'off'.rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.11.1.2 |
atpcTxPowerCorrectionATPC Tx power correction in dBm.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.11.1.3 |
modemTableCFIP modem table. SEQUENCE OF ModemEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12 |
modemEntryEntry containing objects in modem table. ModemEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1 |
modemIndexValue represents UNIT:
1 for local;
2 for remote.ro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.1 |
modemGeneralStatusA General status of each modem:
1 - 'OK';
2 - 'error'ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.2 |
modemBandwithModem bandwidth set in KHz.rw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.3 |
modemE1T1ChannelsNumber of E1 or T1 channels set.rw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.4 |
modemModulationModem modulation set.
Modulution values are
following: QPSK - 1, 8PSK - 2, 16QAM - 3,
32QAM - 4, 64QAM - 5, 128QAM - 6,
256QAM - 7.
The combination of wide band and ACM calculates as
(modulation + 8*is_wide + 16*is_ACM).
Note: not all of listed modulations supported by hardware.
Plese check manual.ro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.5 |
modemTotalCapacityTotal capacity set in Kbps.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.6 |
modemEthernetCapacityEthernet capacity set in Kbps.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.7 |
modemAcqStatusro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.8 |
modemLastAcqErrorro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.9 |
modemRadialMSERadial mean square error value *10 in dB.
Radial MSE is a method for estimating the
signal to noise ratio. ACM engine uses
normalized MSE, which is the inverse of SNR.
It is calculated by dividing the estimated
MSE level with the energy of the received
constellation. Radial MSE peak value threshold
is dependent on modulation used and LDPC
code rate.
In case of QPSK it is -8 dB (-10.5 for 'wide'),
16APSK - -13 dB (-18 for 'wide') and
32APSK - -15.5 dB (-21.5 for 'wide'). If the
value trespasses this threshold, BER at the
output of LDPC decoder will reach the value
of 1.0e-06.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.10 |
modemInternalAGCgaindBmro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.11 |
modemCarrierOffsetCarrier frequency offset in Hz.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.12 |
modemSymbolRateTxkHzro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.13 |
modemSymbolRateRxkHzro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.14 |
modemLDPCdecoderStressThe load of LDPC (low-density
parity-check code) decoder.
The LDPC is monitored for the number
of errors being corrected on the input
of LDPC decoder.
LDPC stress value thresholds @ BER 1.0e-06:
- for standard settings ~4.0e-02;
- for 'wide' option ~ 1.0e-03.
As long as LDPC stress value is under the
specified thresholds, amount of errors (and
BER itself) on the output of LDPC remains
at zero level.ro DisplayString .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.15 |
modemACMengineStatus of ACM engine. When 'on',
value '1' is shown, when 'off' - value is '2'.ro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.16 |
modemACMmodulationMinModem modulation set.
Modulution values are
following: QPSK - 1, 8PSK - 2, 16QAM - 3,
32QAM - 4, 64QAM - 5, 128QAM - 6,
256QAM - 7.
The combination of wide band and ACM calculates as
(modulation + 8*is_wide + 16*is_ACM).
Note: not all of listed modulations supported by hardware.
Plese check manual.rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.17 |
modemACMtotalCapacityTotal capacity in Kbps set by ACM.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.18 |
modemACMethernetCapacityEthernet capacity in Kbps set by ACM.ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.19 |
modemStandardModem operational standard ETSI or ANSIrw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.20 |
modemE1T1ChannelMaskE1 or T1 channel mask 0x00 - 0x0frw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.21 |
modemACMmodulationMaxModem modulation set.
Modulution values are
following: QPSK - 1, 8PSK - 2, 16QAM - 3,
32QAM - 4, 64QAM - 5, 128QAM - 6,
256QAM - 7.
The combination of wide band and ACM calculates as
(modulation + 8*is_wide + 16*is_ACM).
Note: as PSK modulations are now physicaly deprecated,
theese are replased with QAM, so for new QAM modulations
there are modificatior +32.
Note: not all of listed modulations supported by hardware.
Plese check manual.rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.22 |
modemRowStatusRow status - to update written data for
modemBandwith,
modemACMmodulationMin,
modemACMmodulationMax,
modemE1T1ChannelMask.rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.12.1.23 |
vlansEnabledunit temperature *10 degrees Celsiusrw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.13 |
vlanTableVlan table SEQUENCE OF VlanEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14 |
vlanEntryentry containing vlan objects VlanEntry .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14.1 |
vlanNumberA unique value for each vlan.rw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14.1.1 |
vlanPortTypeVLAN port type
management, traffic or endpointrw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14.1.2 |
vlanPortmapdisplay port bindings
bitfield 111(bin)ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14.1.3 |
vlanFida filtering identifier (assigned automagically)ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14.1.4 |
vlanCfgStatenable/disable vlan # or clear row datarw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14.1.5 |
vlanRowStatusRow status (execute configuration on active)
Changing any table value sets this value into
state notReady. To update row status write value
active(1) into this variable.rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.1.1.14.1.6 |
ipRadioCfgNetwork OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1.1.2 |
localIpIPv4 Ethernet address of the local
unit in a number format(XXX.XXX.XXX.XXX)rw IpAddress .1.3.6.1.4.1.7571.100.1.1.5.1.1.2.1 |
localIpMaskIPv4 Ethernet mask of the local
unit in a number format (XXX.XXX.XXX.XXX)rw IpAddress .1.3.6.1.4.1.7571.100.1.1.5.1.1.2.2 |
remoteIpIPv4 Ethernet address of the remote
unit in a number format (XXX.XXX.XXX.XXX).rw IpAddress .1.3.6.1.4.1.7571.100.1.1.5.1.1.2.3 |
ipRadioMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1.2 |
writeConfigWrite Configrw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.2.1 |
restartcpuRestart of Mng CPU. Values:
1 - 'cold' restart;
3 - swrw INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.2.2 |
loopbacksSet loopback for 1 minute. value error(1) is not writable.
Status of loopbacks.
Values:
1 - 'error' (not writable);
2 - 'off';
3 - 'rf' (radio frequency loopback); N/A 2008.10.21
4 - 'if' (intermediate frequency loopback);
5 - 'modem' (modem loopback);
6 - 'far' (far end loopback); N/A 2008.10.21
7 - 'ethernet' (Ethernet loopback); N/A 2008.10.21
8 - 'e1t1-1' (E1/T1 channel 1 loopback); N/A from firmware 1.51
9 - 'e1t1-2' (E1/T1 channel 2 loopback); N/A from firmware 1.51
10 - 'e1t1-3' (E1/T1 channel 3 loopback); N/A from firmware 1.51
11 - 'e1t1-4' (E1/T1 channel 4 loopback); N/A from firmware 1.51
12 - 'multi' (E1/T1 multi - look channel tributary mask)rw Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.2.3 |
loopback-tributary-maskLoopback mask for E1/T1 channelsro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.2.4 |
ipRadioStat OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1.3 |
ipRadioStatEth OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1.3.2 |
ethRXTruncatedFramesNumber of truncated received frames since
unit start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.1 |
ethRXLongEventsNumber of frames having byte count greater
than MAXIMUM FRAME SIZE parameter (1518,
1536 or 1916 bytes) since unit start or
statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.2 |
ethRXVlanTagsDetectedNumber of VLAN Tags detected since unit
start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.3 |
ethRXUnsupOpcodesNumber of frames recognized as control frames
but contained an Unknown Opcode since unit
start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.4 |
ethRXPauseFramesNumber of frames received as control frames
with valid PAUSE opcodes since unit start or
statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.5 |
ethRXControlFramesNumber of frames received as control frames
since unit start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.6 |
ethRXDribleNibblesIndicates that following the end of the
packet additional 1 to 7 bits are received.
A single nibble, named the dribble nibble,
is formed but not sent to the system;ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.7 |
ethRXBroadcastsNumber of packets, which destination
address contained broadcast address,
since unit start or statiistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.8 |
ethRXMulticastsNumber of packets, which destination
address contained multicast address since
unit start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.9 |
ethRXDonesReception of packets successfully
completed. Number of completed packets
since unit start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.10 |
ethRXOutOfRangeErrorsNumber of frames where Type/Length field
larger than 1518 (Type Field) bytes since
unit start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.11 |
ethRXLengthCheckerrorsErrorsNumber of frames where frame length field
in the packet does not match the actual data
byte length and is not a Type Field since
unit start or statistics reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.12 |
ethRXCRCErrorsNumber of frames where frame CRC do not
match the internally generated CRC since
unit start or statistics resetro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.13 |
ethRXCodeErrorsNumber of packets where one or more nibbles
are signalled as errors during reception of
the packet since unit start or statistics
reset.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.14 |
ethRXFalseCarrierErrorsIndicates that following the last receive
statistics vector, a false carrier was
detected, noted and reported with this the
next receive statistics. The false carrier
is not associated with this packet. False
carrier is activated on the receive channel
that does not result in a packet receive
attempt being made;ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.15 |
ethRXDvEventNumber of the last receive (Rx) events seen
being too short to be valid packets since the
last unit (re)start or purification of
statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.16 |
ethRXPrevPktDroppedIndicates that since the last receive (Rx),
a packet is dropped (i.e. interframe gap
too small).ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.17 |
ethRXByteCounterHiTotal number of bytes received (Rx) on the
wire since the last unit (re)start or
purification of statistics, not counting
collided bytes (bits 31:0).ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.18 |
ethRXByteCounterLowTotal number of bytes received (Rx) on the
wire since the last unit (re)start or
purification of statistics, not counting
collided bytes (bits 62:32).ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.19 |
ethTXVlanTagsNumber of VLAN tagged Tx packets since the
last unit (re)start or purification of
statistics. 32-bit counter.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.21 |
ethTXBackpresEventsNumber of times Tx carrier-sense-method
backpressure was previously applied since the
last unit (re)start or purification of
statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.22 |
ethTXPauseFramesNumber of frames transmitted (Tx) as control
frames with valid PAUSE opcodes since the last
unit (re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.23 |
ethTXControlFramesNumber of frames transmitted (Tx) as control
frames since the last unit (re)start or
purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.24 |
ethTXWireByteCounterHiTotal number of bytes transmitted (Tx)
on the wire since the last unit (re)start
or purification of statistics, including
all bytes from collided attempts
(bits 31:0).ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.25 |
ethTXWireByteCounterLowTotal number of bytes transmitted (Tx)
on the wire since the last unit (re)start
or purification of statistics, including
all bytes from collided attempts
(bits 62:32).ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.26 |
ethTXUnderrunsNumber of underruns occured during frame
transmission (Tx) since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.28 |
ethTXGiantsNumber of Tx frames having byte count
greater than the MAXIMUM FRAME SIZE
parameter (1516, 1536 or 1916 bytes)
since the last unit (re)start or
purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.29 |
ethTXLateCollisionsNumber of Tx collisions occurred beyond
the collision window (512 bit times) since
the last unit (re)start or purification
of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.30 |
ethTXMaxCollisionsNumber of Tx packets aborted after number
of collisions exceeded the RETRANSMISSION
MAXIMUM parameter since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.31 |
ethTXExcessiveDefersNumber of Tx packets deferred in excess
of 6,071 nibble times in 100 Mbps mode,
or 24,287 bit-times in 10 Mbps mode since
the last unit (re)start or purification
of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.32 |
ethTXNonExcessiveDefersNumber of Tx packets deferred for at
least one attempt, but less than an
excessive defer since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.33 |
ethTXBroadcastsNumber of Tx packets since the last unit
(re)start or purification of statistics,
which destination address contained
broadcast address.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.34 |
ethTXMulticastsNumber of Tx packets since the last unit
(re)start or purification of statistics,
which destination address contained
multicast address.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.35 |
ethTXDonesNumber of packets successfully transmitted
(Tx) since the last unit (re)start or
purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.36 |
ethTXLengthCheckErrorsNumber of Tx frames since the last unit
(re)start or purification of statistics,
where length field in the packet does not
match the actual data byte length and is
not a Type Fieldro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.38 |
ethTXCRCErrorsNumber of Tx frames since the last unit
(re)start or purification of statistics,
where CRC does not match the internally
generated CRC.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.39 |
ethTXCollisionsNumber of collisions the current packet
incurred during transmission (Tx) attempts.
Note: Bits 19 through 16 are the collision
count on any successfully transmitted packet
and as such will not show the possible maximum
count of 16 collisions.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.40 |
ethTXByteCounterHiTotal count of bytes transmitted (Tx)
on the wire not including collided bytes
(bits 31:0) since the last unit (re)start
or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.41 |
ethTXByteCounterLowTotal count of bytes transmitted (Tx)
on the wire not including collided bytes
(bits 62:32) since the last unit (re)start
or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.42 |
ethGFPFCSErrorsNumber of generic framing procedure (GFP)
frames with CRC errors received by the
de-encapsulation block since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.44 |
ethGFPCHECErrorsNumber of generic framing procedure (GFP)
frames with CHEC errors received by the
de-encapsulation block since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.45 |
ethGFPDropedFramesNumber of generic framing procedure (GFP)
frames that were dropped in the de-encapsulation
block since the last unit (re)start or
purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.46 |
ethGFPDelineationErrorsNumber of 'lost of synchronization' events since
the last unit (re)start or purification of
statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.47 |
ethQOSRXQ1FramesNumber of frames received on Q1 since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.48 |
ethQOSRXQ1DroppedNumber of frames dropped on Q1 since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.49 |
ethQOSRXQ2FramesNumber of frames received on Q2 since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.50 |
ethQOSRXQ2DroppedNumber of frames dropped on Q2 since the last unit
(re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.51 |
ethQOSTXFramesNumber of frames passed through TX FIFO since the
last unit (re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.52 |
ethQOSTXDroppedNumber of frames dropped in TX FIFO since the last
unit (re)start or purification of statistics.ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.2.53 |
e1t1StatTableE1 (T1) status Table. SEQUENCE OF E1t1StatEntry .1.3.6.1.4.1.7571.100.1.1.5.1.3.3 |
e1t1StatEntryEntry containing objects in E1 (T1) table E1t1StatEntry .1.3.6.1.4.1.7571.100.1.1.5.1.3.3.1 |
e1t1LOSif signal loss presentro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.3.3.1.1 |
e1t1AISif AIS presentro Enumeration .1.3.6.1.4.1.7571.100.1.1.5.1.3.3.1.2 |
e1t1ChannelNre1 channel number (it is not associated with interface number - ifEntry)ro INTEGER .1.3.6.1.4.1.7571.100.1.1.5.1.3.3.1.3 |
modemStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.7571.100.1.1.5.1.3.4 |
modemCountTimeCount time in secondsro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.1 |
modemErroredBlockErrored blockro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.2 |
modemErroredSecondErrored secondro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.3 |
modemSeverelyErroredSecondSeverely errored secondro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.4 |
modemBackgroundBlockErrrorBackground Block Errorro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.5 |
modemTotalBlockNumberTotal Block Numberro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.6 |
modemErroredSecondRatioErrored Second Ratioro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.7 |
modemSeverelyErroredSecondRatioSeverely Errored Second Ratioro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.8 |
modemBackgroundBlockErrorRatioBackground Block Error Ratioro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.9 |
modemUptimeUptime (s)ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.10 |
modemUnavailtimeUnavailtime (s)ro Counter .1.3.6.1.4.1.7571.100.1.1.5.1.3.4.11 |