RFC1407-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
92
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
92 total| Object Name |
|---|
ds3 OBJECT IDENTIFIER .1.3.6.1.2.1.10.30 |
RFC1213-MIB Unknown .1.3.6.1.2.1.10.30 |
dsx3ConfigTableThe DS3/E3 Configuration table. SEQUENCE OF Dsx3ConfigEntry .1.3.6.1.2.1.10.30.5 |
dsx3ConfigEntryAn entry in the DS3/E3 Configuration table. Dsx3ConfigEntry .1.3.6.1.2.1.10.30.5.1 |
dsx3LineIndexThis object is the identifier of a DS3/E3
Interface on a managed device. If there is an
ifEntry that is directly associated with this
and only this DS3/E3 interface, it should have
the same value as ifIndex. Otherwise, number
the dsx3LineIndices with an unique identifier
following the rules of choosing a number that
is greater than ifNumber and numbering the
inside interfaces (e.g., equipment side) with
even numbers and outside interfaces (e.g,
network side) with odd numbers.ro INTEGER .1.3.6.1.2.1.10.30.5.1.1 |
dsx3IfIndexThis value for this object is equal to the
value of ifIndex from the Interfaces table of
MIB II (RFC 1213).ro INTEGER .1.3.6.1.2.1.10.30.5.1.2 |
dsx3TimeElapsedThe number of seconds that have elapsed since
the beginning of the near end current error-
measurement period.ro INTEGER .1.3.6.1.2.1.10.30.5.1.3 |
dsx3ValidIntervalsThe number of previous near end intervals for
which valid data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute near end
intervals since the interface has been online.ro INTEGER .1.3.6.1.2.1.10.30.5.1.4 |
dsx3LineTypeThis variable indicates the variety of DS3 C-bit
or E3 application
implementing this interface. The type of
interface affects the interpretation of the
usage and error statistics.
The rate of DS3 is 44.736 Mbps and E3 is
34.368 Mbps.
The dsx3ClearChannel value means that the C-bits
are not used except for sending/receiving
AIS.
The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3M23 ANSI T1.107-1988
dsx3SYNTRAN ANSI T1.107-1988
dsx3CbitParity ANSI T1.107a-1989
dsx3ClearChannel ANSI T1.102-1987
e3Framed CCITT G.751
e3Plcp ETSI T/NA(91)18.rw Enumeration .1.3.6.1.2.1.10.30.5.1.5 |
dsx3LineCodingThis variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.rw Enumeration .1.3.6.1.2.1.10.30.5.1.6 |
dsx3SendCodeThis variable indicates what type of code is
being sent across the DS3/E3 interface by the
device. (These are optional for E3 interfaces.)
The values mean:
dsx3SendNoCode
sending looped or normal data
dsx3SendLineCode
sending a request for a line loopback
dsx3SendPayloadCode
sending a request for a payload loopback
(i.e., all DS1/E1s in a DS3/E3 frame)
dsx3SendResetCode
sending a loopback deactivation request
dsx3SendDS1LoopCode
requesting to loopback a particular DS1/E1
within a DS3/E3 frame
dsx3SendTestPattern
sending a test pattern.rw Enumeration .1.3.6.1.2.1.10.30.5.1.7 |
dsx3CircuitIdentifierThis variable contains the transmission vendor's
circuit identifier, for the purpose of
facilitating troubleshooting.rw DisplayString .1.3.6.1.2.1.10.30.5.1.8 |
dsx3LoopbackConfigThis variable represents the loopback configuration
of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx3PayloadLoop
The received signal at this interface is looped
through the device.
Typically the received signal
is looped back for retransmission after it has
passed through the device's framing function.
dsx3LineLoop
The received signal at this interface does not
go through the device (minimum penetration) but
is looped back out.
dsx3OtherLoop
Loopbacks that are not defined here.rw Enumeration .1.3.6.1.2.1.10.30.5.1.9 |
dsx3LineStatusThis variable indicates the
Line Status of the interface.
It contains loopback state information
and failure state information.
The dsx3LineStatus is a bit map represented
as a sum, therefore,
it can represent multiple failures
and a loopback (see dsx3LoopbackConfig object
for the type of loopback)
simultaneously.
The dsx3NoAlarm should be set if and only if
no other flag is set.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
herero INTEGER .1.3.6.1.2.1.10.30.5.1.10 |
dsx3TransmitClockSourceThe source of Transmit Clock.
is derived from the recovered receive clock of
another DS3 interface.rw Enumeration .1.3.6.1.2.1.10.30.5.1.11 |
dsx3CurrentTableThe DS3/E3 Current table. SEQUENCE OF Dsx3CurrentEntry .1.3.6.1.2.1.10.30.6 |
dsx3CurrentEntryAn entry in the DS3/E3 Current table. Dsx3CurrentEntry .1.3.6.1.2.1.10.30.6.1 |
dsx3CurrentIndexThe index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.ro INTEGER .1.3.6.1.2.1.10.30.6.1.1 |
dsx3CurrentPESsThe counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.2 |
dsx3CurrentPSESsThe counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.3 |
dsx3CurrentSEFSsThe counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in the current 15 minute
interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.4 |
dsx3CurrentUASsThe counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.5 |
dsx3CurrentLCVsThe counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.6 |
dsx3CurrentPCVsThe counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.7 |
dsx3CurrentLESsThe number of Line Errored Seconds encountered by
a DS3/E3 interface in the current 15 minute
interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.8 |
dsx3CurrentCCVsThe number of C-bit Coding Violations encountered
by a DS3 interface in the current 15 minute
interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.9 |
dsx3CurrentCESsThe number of C-bit Errored Seconds encountered
by a DS3 interface in the current 15 minute
interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.10 |
dsx3CurrentCSESsThe number of C-bit Severely Errored Seconds
encountered by a DS3 interface in the current 15
minute interval.ro Gauge .1.3.6.1.2.1.10.30.6.1.11 |
dsx3IntervalTableThe DS3/E3 Interval table. SEQUENCE OF Dsx3IntervalEntry .1.3.6.1.2.1.10.30.7 |
dsx3IntervalEntryAn entry in the DS3/E3 Interval table. Dsx3IntervalEntry .1.3.6.1.2.1.10.30.7.1 |
dsx3IntervalIndexThe index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.ro INTEGER .1.3.6.1.2.1.10.30.7.1.1 |
dsx3IntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro INTEGER .1.3.6.1.2.1.10.30.7.1.2 |
dsx3IntervalPESsThe counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
one of the previous 96, individual 15 minute,
intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.3 |
dsx3IntervalPSESsThe counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in one of the previous 96, individual 15
minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.4 |
dsx3IntervalSEFSsThe counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.5 |
dsx3IntervalUASsThe counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in one of the previous 96, individual 15
minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.6 |
dsx3IntervalLCVsThe counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in one of the previous 96, individual 15
minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.7 |
dsx3IntervalPCVsThe counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in one of the previous 96, individual 15 minute,
intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.8 |
dsx3IntervalLESsThe number of Line Errored Seconds (BPVs or
illegal zero sequences) encountered by a DS3/E3
interface in one of the previous 96, individual
15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.9 |
dsx3IntervalCCVsThe number of C-bit Coding Violations encountered
by a DS3 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.10 |
dsx3IntervalCESsThe number of C-bit Errored Seconds encountered
by a DS3 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.11 |
dsx3IntervalCSESsThe number of C-bit Severely Errored Seconds
encountered by a DS3 interface in one of the
previous 96, individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.7.1.12 |
dsx3TotalTableThe DS3/E3 Total table. 24 hour interval. SEQUENCE OF Dsx3TotalEntry .1.3.6.1.2.1.10.30.8 |
dsx3TotalEntryAn entry in the DS3/E3 Total table. Dsx3TotalEntry .1.3.6.1.2.1.10.30.8.1 |
dsx3TotalIndexThe index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.ro INTEGER .1.3.6.1.2.1.10.30.8.1.1 |
dsx3TotalPESsThe counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
the previous 24 hour intervalro Gauge .1.3.6.1.2.1.10.30.8.1.2 |
dsx3TotalPSESsThe counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.3 |
dsx3TotalSEFSsThe counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in the previous 24 hour
interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.4 |
dsx3TotalUASsThe counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.5 |
dsx3TotalLCVsThe counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.6 |
dsx3TotalPCVsThe counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.7 |
dsx3TotalLESsThe number of Line Errored Seconds (BPVs or
illegal zero sequences) encountered by a DS3/E3
interface in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.8 |
dsx3TotalCCVsThe number of C-bit Coding Violations encountered
by a DS3 interface in the previous 24 hour
interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.9 |
dsx3TotalCESsThe number of C-bit Errored Seconds encountered
by a DS3 interface in the previous 24 hour
interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.10 |
dsx3TotalCSESsThe number of C-bit Severely Errored Seconds
encountered by a DS3 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.2.1.10.30.8.1.11 |
dsx3FarEndConfigTableThe DS3 Far End Configuration table. SEQUENCE OF Dsx3FarEndConfigEntry .1.3.6.1.2.1.10.30.9 |
dsx3FarEndConfigEntryAn entry in the DS3 Far End Configuration table. Dsx3FarEndConfigEntry .1.3.6.1.2.1.10.30.9.1 |
dsx3FarEndLineIndexThe index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The
interface identified by a particular value of
this index is the same interface as identified
by the same value an dsx3LineIndex object
instance.ro INTEGER .1.3.6.1.2.1.10.30.9.1.1 |
dsx3FarEndEquipCodeThis is the Far End Equipment Identification code
that describes the specific piece of equipment.
It is sent within the Path
Identification Message.rw DisplayString .1.3.6.1.2.1.10.30.9.1.2 |
dsx3FarEndLocationIDCodeThis is the Far End Location Identification code
that describes the specific location of the
equipment.
It is sent within the Path
Identification Message.rw DisplayString .1.3.6.1.2.1.10.30.9.1.3 |
dsx3FarEndFrameIDCodeThis is the Far End Frame Identification code
that identifies where the equipment is located
within a building at a given location.
It is sent within the Path
Identification Message.rw DisplayString .1.3.6.1.2.1.10.30.9.1.4 |
dsx3FarEndUnitCodeThis is the Far End code
that identifies the equipment location within a bay.
It is sent within the Path
Identification Message.rw DisplayString .1.3.6.1.2.1.10.30.9.1.5 |
dsx3FarEndFacilityIDCodeThis code identifies a specific Far End DS3 path.
It is sent within the Path
Identification Message.rw DisplayString .1.3.6.1.2.1.10.30.9.1.6 |
dsx3FarEndCurrentTableThe DS3 Far End Current table. SEQUENCE OF Dsx3FarEndCurrentEntry .1.3.6.1.2.1.10.30.10 |
dsx3FarEndCurrentEntryAn entry in the DS3 Far End Current table. Dsx3FarEndCurrentEntry .1.3.6.1.2.1.10.30.10.1 |
dsx3FarEndCurrentIndexThe index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The interface
identified by a particular value of this index is
the same interface as identified by the same value
an dsx3LineIndex object instance.ro INTEGER .1.3.6.1.2.1.10.30.10.1.1 |
dsx3FarEndTimeElapsedThe number of seconds that have elapsed since the
beginning of the far end current error-measurement
period.ro INTEGER .1.3.6.1.2.1.10.30.10.1.2 |
dsx3FarEndValidIntervalsThe number of previous far end intervals for
which valid data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute far end intervals
since the interface has been online.ro INTEGER .1.3.6.1.2.1.10.30.10.1.3 |
dsx3FarEndCurrentCESsThe counter associated with the number of Far
Far End C-bit Errored Seconds encountered by a DS3
interface in the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.10.1.4 |
dsx3FarEndCurrentCSESsThe counter associated with the number of
Far End C-bit Severely Errored Seconds
encountered by a DS3 interface in the current 15
minute interval.ro Gauge .1.3.6.1.2.1.10.30.10.1.5 |
dsx3FarEndCurrentCCVsThe counter associated with the number of
Far End C-bit Coding Violations reported via
the far end block error count
encountered by a
DS3 interface in the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.10.1.6 |
dsx3FarEndCurrentUASsThe counter associated with the number of
Far End unavailable seconds
encountered by a
DS3 interface in the current 15 minute interval.ro Gauge .1.3.6.1.2.1.10.30.10.1.7 |
dsx3FarEndIntervalTableThe DS3 Far End Interval table. SEQUENCE OF Dsx3FarEndIntervalEntry .1.3.6.1.2.1.10.30.11 |
dsx3FarEndIntervalEntryAn entry in the DS3 Far
End Interval table. Dsx3FarEndIntervalEntry .1.3.6.1.2.1.10.30.11.1 |
dsx3FarEndIntervalIndexThe index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The
interface identified by a particular value of
this index is the same interface as identified
by the same value an dsx3LineIndex object
instance.ro INTEGER .1.3.6.1.2.1.10.30.11.1.1 |
dsx3FarEndIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes
interval (assuming that all 96 intervals are
valid).ro INTEGER .1.3.6.1.2.1.10.30.11.1.2 |
dsx3FarEndIntervalCESsThe counter associated with the number of
Far End C-bit Errored Seconds encountered
by a DS3 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.11.1.3 |
dsx3FarEndIntervalCSESsThe counter associated with the number of
Far End C-bit Severely Errored Seconds
encountered by a DS3 interface in one of the
previous 96, individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.11.1.4 |
dsx3FarEndIntervalCCVsThe counter associated with the number of
Far End C-bit Coding Violations reported via
the far end block error count
encountered by a
DS3 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.11.1.5 |
dsx3FarEndIntervalUASsThe counter associated with the number of
Far End unavailable seconds
encountered by a
DS3 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge .1.3.6.1.2.1.10.30.11.1.6 |
dsx3FarEndTotalTableThe DS3 Far End Total table. 24 hour interval. SEQUENCE OF Dsx3FarEndTotalEntry .1.3.6.1.2.1.10.30.12 |
dsx3FarEndTotalEntryAn entry in the DS3 Far End Total table. Dsx3FarEndTotalEntry .1.3.6.1.2.1.10.30.12.1 |
dsx3FarEndTotalIndexThe index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The interface
identified by a particular value of this index is
the same interface as identified by the same value
an dsx3LineIndex object instance.ro INTEGER .1.3.6.1.2.1.10.30.12.1.1 |
dsx3FarEndTotalCESsThe counter associated with the number of Far
End C-bit Errored Seconds encountered by a DS3
interface in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.12.1.2 |
dsx3FarEndTotalCSESsThe counter associated with the number of
Far End C-bit Severely Errored Seconds
encountered by a DS3 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.2.1.10.30.12.1.3 |
dsx3FarEndTotalCCVsThe counter associated with the number of
Far End C-bit Coding Violations reported via the
far end block error count
encountered by a
DS3 interface in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.12.1.4 |
dsx3FarEndTotalUASsThe counter associated with the number of
Far End unavailable seconds
encountered by a
DS3 interface in the previous 24 hour interval.ro Gauge .1.3.6.1.2.1.10.30.12.1.5 |
dsx3FracTableThe DS3 Fractional table. SEQUENCE OF Dsx3FracEntry .1.3.6.1.2.1.10.30.13 |
dsx3FracEntryAn entry in the DS3 Fractional table. Dsx3FracEntry .1.3.6.1.2.1.10.30.13.1 |
dsx3FracIndexThe index value which uniquely identifies the
DS3 interface to which this entry is applicable
The interface identified by a particular
value of this index is the same interface as
identified by the same value an dsx3LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.2.1.10.30.13.1.1 |
dsx3FracNumberThe channel number for this entry.ro INTEGER .1.3.6.1.2.1.10.30.13.1.2 |
dsx3FracIfIndexAn index value that uniquely identifies an
interface. The interface identified by a particular
value of this index is the same interface
as identified by the same value an ifIndex
object instance. If no interface is currently using
a channel, the value should be zero. If a
single interface occupies more than one time
slot, that ifIndex value will be found in multiple
time slots.rw INTEGER (1..'7fffffff'h) .1.3.6.1.2.1.10.30.13.1.3 |