QB-ATM-MIB
AI MIB Summary
The QB-ATM-MIB extends standard ATM management capabilities to monitor and control ATM link parameters on Quantum Bridge hardware, specifically exposing vendor-specific objects and counters not defined in the IETF standard ATM-MIB. This module enables granular visibility into ATM interface states, traffic statistics, and error conditions unique to the Quantum Bridge platform.
This module defines additional objects for management of ATM links in Quantum Bridge devices, above and beyond what is defined in the standard ATM mib, and proposed drafts.
Main OID:
qbAtmMIB.1.3.6.1.4.1.4323.2.7
174
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
174 total| Object Name |
|---|
qbAtmMIBThis module defines additional objects for management of ATM
links in Quantum Bridge devices, above and beyond what is defined in the
standard ATM mib, and proposed drafts. MODULE-IDENTITY .1.3.6.1.4.1.4323.2.7 |
qbAtmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.1 |
qbAtmInterfaceConfTableThe Quantum Bridge ATM Interface Configuration Table contains
extensions to the ATM Interface Configuration Table,
one entry per ATM interface. SEQUENCE OF QbAtmInterfaceConfEntry .1.3.6.1.4.1.4323.2.7.1.1 |
qbAtmInterfaceConfEntryAn entry in the Quantum ATM Interface Configuration
Table. Every ATM interface contains a corresponding
entry in the table. QbAtmInterfaceConfEntry .1.3.6.1.4.1.4323.2.7.1.1.1 |
qbAtmInterfaceConfPolicingStatusIf this object is set to 'enable' the policing is enabled on this
interface. If the object set to 'disable,' the policing is
disabled. Note: policing can be set on the S622 and 155
cards only.rw Enumeration .1.3.6.1.4.1.4323.2.7.1.1.1.1 |
qbAtmInterfaceConfMaxPvcVpiThis object indicates the maximum value of VPI that can be
used to create a VC on a given ATM native interface.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.1.1.2 |
qbAtmInterfaceConfMinPvcVpiThis object indicates the minimum value of VPI that can be
used to create a VC on a given ATM native interface.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.1.1.3 |
qbAtmInterfaceConfMaxPvcVciThis object indicates the maximum value of VCI that can be
used to create a VC on a given ATM native interface.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.1.1.4 |
qbAtmInterfaceConfMinPvcVciThis object indicates the minimum value of VCI that can be
used to create a VC on a given ATM native interface.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.1.1.5 |
qbAtmInterfaceConfMaxPvpVpiThis object indicates the maximum value of VPI that can be
used to create a VP on a given ATM native interface.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.1.1.6 |
qbAtmInterfaceConfMinPvpVpiThis object indicates the minimum value of VPI that can be
used to create a VP on a given ATM native interface.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.1.1.7 |
qbAtmTrafficDescrParamTableThe Quantum Bridge ATM Traffic Descriptor Table contains
extensions to the ATM Traffic Descriptor Table. SEQUENCE OF QbAtmTrafficDescrParamEntry .1.3.6.1.4.1.4323.2.7.1.2 |
qbAtmTrafficDescrParamEntryAn entry in the Quantum Bridge ATM Traffic Descriptor Table. QbAtmTrafficDescrParamEntry .1.3.6.1.4.1.4323.2.7.1.2.1 |
qbAtmTrafficDescrParamNameA textual description of the traffic descriptor.rw DisplayString .1.3.6.1.4.1.4323.2.7.1.2.1.1 |
qbAtmTrafficDescrParamDefaultThe object indicates whether or not this is a default
traffic descriptor.
Traffic descriptor with indexes from 1 to 20
are default traffic descriptors and cannot be
deleted.ro Boolean .1.3.6.1.4.1.4323.2.7.1.2.1.2 |
qbAtmVclTableThe Quantum Bridge Table contains an extension to
the atmVclConnectTable,
An entry in this table models VCLs. SEQUENCE OF QbAtmVclEntry .1.3.6.1.4.1.4323.2.7.1.3 |
qbAtmVclEntryAn entry in the QB ATM atmVclConnectTable. QbAtmVclEntry .1.3.6.1.4.1.4323.2.7.1.3.1 |
qbAtmVclLoopbackEnable loopback on this ATM VCLrw QbEnableStatus (QB-DWS-MIB) .1.3.6.1.4.1.4323.2.7.1.3.1.1 |
qbAtmVclF4F5LoopbackInsertThis is a loopback Insert object for LLID.
Start loopback Insert by setting this to an LLID value.rw OCTET STRING .1.3.6.1.4.1.4323.2.7.1.3.1.2 |
qbAtmVclF4F5LoopbackStatusStatus of loopback Insert command: in-progress, success, timeout.ro QbF4F5LoopbackStatus .1.3.6.1.4.1.4323.2.7.1.3.1.3 |
qbAtmVclF4F5LoopbackTimestampValue of sysUptime when last Insert completed.ro TimeStamp (QBSYS-SYSTEM-MIB) .1.3.6.1.4.1.4323.2.7.1.3.1.4 |
qbAtmVclMgmtIpAddrActive IP Address for in-band Management SNMP of this chassis.rw IpAddress .1.3.6.1.4.1.4323.2.7.1.3.1.5 |
qbAtmVclMgmtIpMaskThis is the IP network mask associated with the in-band
Management interface.rw IpAddress .1.3.6.1.4.1.4323.2.7.1.3.1.6 |
qbAtmVclMgmtNeighborIPThis is the neighbor IP address associated with the in-band
Management interface.rw IpAddress .1.3.6.1.4.1.4323.2.7.1.3.1.7 |
qbAtmVclConnKindThe VCL connection type.ro QbPvcConnKind (QB-DWS-MIB) .1.3.6.1.4.1.4323.2.7.1.3.1.8 |
qbAtmVclF4F5TxStatusThe transmitted OAM status for the PVC.ro QbF4F5Status .1.3.6.1.4.1.4323.2.7.1.3.1.9 |
qbAtmVclF4F5TxLastChangeThe value of sysUPtime when qbAtmVclF4F5TxStatus last changed.ro TimeStamp (QBSYS-SYSTEM-MIB) .1.3.6.1.4.1.4323.2.7.1.3.1.10 |
qbAtmVclF4F5RxStatusThe received OAM status of the PVC.ro QbF4F5Status .1.3.6.1.4.1.4323.2.7.1.3.1.11 |
qbAtmVclF4F5RxLastChangeThe value of sysUPtime when qbAtmVclF4F5TxStatus last changed.ro TimeStamp (QBSYS-SYSTEM-MIB) .1.3.6.1.4.1.4323.2.7.1.3.1.12 |
qbAtmVplTableThe Quantum Bridge Table contains an extension to
the atmVclConnectTable,
An entry in this table models VPLs. SEQUENCE OF QbAtmVplEntry .1.3.6.1.4.1.4323.2.7.1.4 |
qbAtmVplEntryAn entry in the QB ATM qbAtmVpTable. QbAtmVplEntry .1.3.6.1.4.1.4323.2.7.1.4.1 |
qbAtmVplLoopbackEnable loopback on this ATM VPLrw QbEnableStatus (QB-DWS-MIB) .1.3.6.1.4.1.4323.2.7.1.4.1.1 |
qbAtmVplF4F5LoopbackInsertThis is a loopback Insert object for LLID.
Start loopback Insert by setting this to an LLID value.rw OCTET STRING .1.3.6.1.4.1.4323.2.7.1.4.1.2 |
qbAtmVplF4F5LoopbackStatusStatus of loopback Insert command: in-progress, success, timeout.ro QbF4F5LoopbackStatus .1.3.6.1.4.1.4323.2.7.1.4.1.3 |
qbAtmVplF4F5LoopbackTimestampValue of sysUptime when last Insert completed.ro TimeStamp (QBSYS-SYSTEM-MIB) .1.3.6.1.4.1.4323.2.7.1.4.1.4 |
qbAtmVplF4F5TxStatusThe transmitted OAM status for the PVP.ro QbF4F5Status .1.3.6.1.4.1.4323.2.7.1.4.1.5 |
qbAtmVplF4F5TxLastChangeThe value of sysUPtime when qbAtmVclF4F5TxStatus last changed.ro TimeStamp (QBSYS-SYSTEM-MIB) .1.3.6.1.4.1.4323.2.7.1.4.1.6 |
qbAtmVplF4F5RxStatusThe received OAM status of the PVP.ro QbF4F5Status .1.3.6.1.4.1.4323.2.7.1.4.1.7 |
qbAtmVplF4F5RxLastChangeThe value of sysUPtime when qbAtmVclF4F5TxStatus last changed.ro TimeStamp (QBSYS-SYSTEM-MIB) .1.3.6.1.4.1.4323.2.7.1.4.1.8 |
qbAtmVcCrossConnectTableThe Quantum Bridge Table contains an extension to
the atmVcCrossConnectTable,
An entry in this table models two cross-connected VCLs. SEQUENCE OF QbAtmVcCrossConnectEntry .1.3.6.1.4.1.4323.2.7.1.5 |
qbAtmVcCrossConnectEntryAn entry in the QB ATM atmVcCrossConnectTable. QbAtmVcCrossConnectEntry .1.3.6.1.4.1.4323.2.7.1.5.1 |
qbAtmVcCrossConnectNameA textual description for the cross connect.rw DisplayString .1.3.6.1.4.1.4323.2.7.1.5.1.1 |
qbAtmVcCrossConnectRxTrafficDescrIndexThe value of this object identifies the row
in the ATM Traffic Descriptor Table which
applies to the receive direction of this VCLs cross-connect.rw AtmTrafficDescrParamIndex (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.5.1.2 |
qbAtmVcCrossConnectTxTrafficDescrIndexThe value of this object identifies the row
of the ATM Traffic Descriptor Table which applies
to the transmit direction of this VCLs cross-connectrw AtmTrafficDescrParamIndex (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.5.1.3 |
qbAtmVpCrossConnectTableThe Quantum Bridge Table contains an extension to
the atmVpCrossConnectTable,
An entry in this table models two cross-connected VPLs. SEQUENCE OF QbAtmVpCrossConnectEntry .1.3.6.1.4.1.4323.2.7.1.6 |
qbAtmVpCrossConnectEntryAn entry in the QB ATM atmVpCrossConnectTable. QbAtmVpCrossConnectEntry .1.3.6.1.4.1.4323.2.7.1.6.1 |
qbAtmVpCrossConnectNameA textual description for the cross connect.rw DisplayString .1.3.6.1.4.1.4323.2.7.1.6.1.1 |
qbAtmVpCrossConnectRxTrafficDescrIndexThe value of this object identifies the row
in the ATM Traffic Descriptor Table which
applies to the receive direction of this VPLs cross-connect.rw AtmTrafficDescrParamIndex (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.6.1.2 |
qbAtmVpCrossConnectTxTrafficDescrIndexThe value of this object identifies the row
of the ATM Traffic Descriptor Table which applies
to the transmit direction of this VPLs cross-connectrw AtmTrafficDescrParamIndex (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.6.1.3 |
qbAtmSigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.1.7 |
qbAtmPnniNodeTableThe QbAtmpnniNodeTable contains attributes that affect the
operation of a PNNI logical node.
There is a single row in this table for each PNNI peer
group that the managed system is expected or eligible
to become a member of. SEQUENCE OF QbAtmPnniNodeEntry .1.3.6.1.4.1.4323.2.7.1.7.1 |
qbAtmPnniNodeEntryAn entry in the table, containing information about a PNNI
logical node in this switching system. QbAtmPnniNodeEntry .1.3.6.1.4.1.4323.2.7.1.7.1.1 |
qbAtmPnniNodeIndexA value assigned to a node in this switching system that
uniquely identifies it in the MIB. INTEGER .1.3.6.1.4.1.4323.2.7.1.7.1.1.1 |
qbAtmPnniNodeNetAddrPrefixIndicates the Network Prefix to use for the ATM End
System Address. The value is 13 bytes long, and is
specified in the hexadecimal format. If less than 13
bytes(26 chars) are received, the agent appends
trailing zero's. The object can be set to ''h, if PNNI
protocol is desirable on all interfaces.rw OCTET STRING .1.3.6.1.4.1.4323.2.7.1.7.1.1.2 |
qbAtmPnniNodeEndSysIdIndicates the End System Identifier for ATM End
System Address. The value is 7 bytes long, and is
specified in the hexadecimal format.
The object can be set to ''h, if PNNI
protocol is desirable on all interfaces.rw OCTET STRING .1.3.6.1.4.1.4323.2.7.1.7.1.1.3 |
qbAtmPnniNodeLevelThe level of PNNI hierarchy at which this node exists. This
attribute is used to determine the default node ID and the
default peer group ID for this node. This object may only
be written when pnniNodeAdminStatus has the value down.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.1.1.4 |
qbAtmPnniNodeRowStatusTo create, delete, activate and de-activate a Node.
Setting this object to createAndGo(4) causes
the corresponding row to be created.
Setting this object to destroy(6) causes the corresponding
row to be deleted.
Note that only a single instance of a row
can be created in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4323.2.7.1.7.1.1.5 |
qbAtmPnniNodeOperStatusIndicates the Operational Status of the PNNI Node. For Logical Group
Nodes, the Operational Status will be up only if the child becomes the
PGL.ro Enumeration .1.3.6.1.4.1.4323.2.7.1.7.1.1.6 |
qbAtmPnniNodeAtmAddressThis node's ATM End System Address. Remote systems wishing
to exchange PNNI protocol packets with this node should
direct packets or calls to this address.
The current Qb implementation does not support writing this value.ro QbAtmPnniAtmAddr .1.3.6.1.4.1.4323.2.7.1.7.1.1.7 |
qbAtmPnniNodePeerGroupIdThe Peer Group Identifier of the peer group that the given
node is to become a member of.ro QbAtmPnniPeerGroupId .1.3.6.1.4.1.4323.2.7.1.7.1.1.8 |
qbAtmPnniIfTableThe qbAtmPnniIfTable contains the attributes necessary to
configure a physical interface on a switching system
capable of being used for PNNI routing.
An ifIndex is used as the instance ID to uniquely identify
the interface on the local switching system. This index has
the same value as the ifIndex object defined in RFC 1573
for the same interface, since this table correlates with
the ifTable in RFC 1573.
One row in this table is created by the managed system for
each row in the ifTable that has an ifType of atm(37) or
atmLogical(80). SEQUENCE OF QbAtmPnniIfEntry .1.3.6.1.4.1.4323.2.7.1.7.2 |
qbAtmPnniIfEntryAn entry in the table, containing PNNI specific interface
information in this switching system. QbAtmPnniIfEntry .1.3.6.1.4.1.4323.2.7.1.7.2.1 |
qbAtmPnniIfNodeIndexIdentifies the node within the switching system that the
interface is directly attached to. Note: For this release
this value can be set only to 1.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.2.1.1 |
qbAtmPnniIfAdmWeightCbrThe administrative weight of this interface for the
constant bit rate service category.rw QbAtmPnniWeight .1.3.6.1.4.1.4323.2.7.1.7.2.1.2 |
qbAtmPnniIfAdmWeightRtVbrThe administrative weight of this interface for the
real-time variable bit rate service category.rw QbAtmPnniWeight .1.3.6.1.4.1.4323.2.7.1.7.2.1.3 |
qbAtmPnniIfAdmWeightNrtVbrThe administrative weight of this interface for the
non-real-time variable bit rate service category.rw QbAtmPnniWeight .1.3.6.1.4.1.4323.2.7.1.7.2.1.4 |
qbAtmPnniIfAdmWeightAbrThe administrative weight of this interface for the
available bit rate service category.rw QbAtmPnniWeight .1.3.6.1.4.1.4323.2.7.1.7.2.1.5 |
qbAtmPnniIfAdmWeightUbrThe administrative weight of this interface for the
unspecified bit rate service category.rw QbAtmPnniWeight .1.3.6.1.4.1.4323.2.7.1.7.2.1.6 |
qbAtmPnniIfRccServiceCategoryThe service category used for the PNNI routing control
channel (VCI=18) on this interface.rw AtmServiceCategory (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.7.2.1.7 |
qbAtmPnniIfRccTrafficDescrIndexThe traffic descriptor index referring to the entry in the
atmTrafficDescrParamTable defined in RFC 1695 that
specifies the traffic allocation for the PNNI routing
control channel (VCI=18) on this interface.rw AtmTrafficDescrParamIndex (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.7.2.1.8 |
qbAtmPnniIfPolicingStatusIf this object is set to enable, the policing is enabled on this
interface. If the object is set to 'disable' the policing is
disabled.rwdeprecated Enumeration .1.3.6.1.4.1.4323.2.7.1.7.2.1.9 |
qbAtmPnniRouteAddrTableA table containing all the attributes necessary to
determine what the PNNI entity believes is reachable in
terms of ATM End System Addresses, and to determine which
nodes are advertising this reachability. This table is
also used to configure static routes to reachable address
prefixes. The local node index that receives the
reachability information, reachable address, address prefix
length, and an index that distinguishes between multiple
listings of connectivity to a given address prefix from a
given local node are combined to form an instance ID for
this object. SEQUENCE OF QbAtmPnniRouteAddrEntry .1.3.6.1.4.1.4323.2.7.1.7.3 |
qbAtmPnniRouteAddrEntryAn entry in the table, containing information about a
reachable address prefix. QbAtmPnniRouteAddrEntry .1.3.6.1.4.1.4323.2.7.1.7.3.1 |
qbAtmPnniRouteAddrIfIndexThe local interface over which the reachable address can be
reached. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4323.2.7.1.7.3.1.1 |
qbAtmPnniRouteAddrAddressThe value of the ATM End System Address prefix. OCTET STRING .1.3.6.1.4.1.4323.2.7.1.7.3.1.2 |
qbAtmPnniRouteAddrPrefixLengthIndicates the number of bits to be applied to the ATM End System
Address prefix.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.3.1.3 |
qbAtmPnniRouteAddrRowStatusTo create, delete, activate and de-activate a reachable
address prefix.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4323.2.7.1.7.3.1.4 |
qbAtmPnniRouteAddrProtoThis object indicates the Routing mechanism through which
the connectivity from the advertising node to the
reachable address prefix was learned.ro Enumeration .1.3.6.1.4.1.4323.2.7.1.7.3.1.5 |
qbAtmInterfaceConfSigTableThis table contains ATM local interface configuration
parameters, one entry per ATM interface port. SEQUENCE OF QbAtmInterfaceConfSigEntry .1.3.6.1.4.1.4323.2.7.1.7.4 |
qbAtmInterfaceConfSigEntryThis list contains additonal ATM interface configuration
parameters and state variables. QbAtmInterfaceConfSigEntry .1.3.6.1.4.1.4323.2.7.1.7.4.1 |
qbAtmInterfaceConfSigModeThe type of ATM interface which is either a UNI
(User to Network), PNNI or IISP.
To modify the qbAtmInterfaceConfSignType, ifAdminStatus has
to be down.rw QbAtmSigSpec .1.3.6.1.4.1.4323.2.7.1.7.4.1.1 |
qbAtmInterfaceConfSigSideThe side of ATM interface which is either a user or
network side. NotApplicable value implies that
qbAtmInterfaceConfSignType is other than uni or iisp.rw Enumeration .1.3.6.1.4.1.4323.2.7.1.7.4.1.2 |
qbAtmInterfaceConfSigParseModeIndicates to the signalling stack to use strict
parsing of the INformation Elements (IEs) within
signalling messages. This parameter is set to 'on' for
conformance testing. For systems that do not test
conformance it is recommended to set the object to
'off'.rw Enumeration .1.3.6.1.4.1.4323.2.7.1.7.4.1.3 |
qbAtmInterfaceConfSigAdminStatusEnable/Disable signalling/sscop on this interface.
To modify the qbAtmInterfaceConfSignAdminStatus,
ifAdminStatus has to be down.rw Enumeration .1.3.6.1.4.1.4323.2.7.1.7.4.1.4 |
qbAtmInterfaceConfSigSvcMinVciThe minimum value of SVC connection for vci.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.4.1.5 |
qbAtmInterfaceConfSigSvcMaxVciThe maximum value of SVC connection for vci.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.4.1.6 |
qbAtmInterfaceConfSigSvcMinVpiThe minimum value of SVC connection for vpi.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.4.1.7 |
qbAtmInterfaceConfSigSvcMaxVpiThe maximum value of SVC connection for vpi.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.4.1.8 |
qbAtmInterfaceConfSigSvpMinVpiThe minimum value of SVP connection for vpi.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.4.1.9 |
qbAtmInterfaceConfSigSvpMaxVpiThe maximum value of SVP connection for vpi.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.4.1.10 |
qbAtmInterfaceConfSigLastChangeThe value of sysUpTime at the time this
interface changed its current administrative state.ro AtmVorXLastChange (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.7.4.1.11 |
qbAtmInterfaceConfSigIlmiEnableCan be enabled only if signaling is configured. ILMI is enabled by default when signaling
is configured on the system and the user may enter the disable option .rw Boolean .1.3.6.1.4.1.4323.2.7.1.7.4.1.12 |
qbAtmPnniNbrPeerTableThe qbAtmPnniNbrPeer Object contains all the attributes
necessary to describe the relationship a node in this
switching system has with a neighboring node within the
same peer group. A concatenation of the Node Identifier of
the node within the local switching system and the
neighboring peer's Node Identifier is used to form the
instance ID for this object.
The entire qbAtmPnniNbrPeer object is read-only, reflecting the
fact that neighboring peers are discovered dynamically by
the PNNI protocol rather than configured. SEQUENCE OF QbAtmPnniNbrPeerEntry .1.3.6.1.4.1.4323.2.7.1.7.5 |
qbAtmPnniNbrPeerEntryAn entry in the table, containing information about this
node's relationship with a neighboring peer node. QbAtmPnniNbrPeerEntry .1.3.6.1.4.1.4323.2.7.1.7.5.1 |
qbAtmPnniPeerRemoteNodeIdThe Node Identifier of the neighboring peer node. QbAtmPnniNodeId .1.3.6.1.4.1.4323.2.7.1.7.5.1.1 |
qbAtmPnniPeerStateIndicates the state of this node's Neighboring Peer State
Machine associated with qbAtmPnniPeerRemoteNodeId.ro Enumeration .1.3.6.1.4.1.4323.2.7.1.7.5.1.2 |
qbAtmPnniPeerSvccRccIndexIdentifies the SVCC-based RCC being used to communicate
with the neighboring peer if one exists. If both the local
node and the neighboring peer node are lowest-level nodes,
this attribute is set to zero.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.7.5.1.3 |
qbAtmPnniPeerPortCountA count of the total number of ports that connect to the
neighboring peer. If the neighboring peer only
communicates via an SVCC-based RCC, the value of this
attribute is set to zero. Otherwise it is set to the total
number of ports to the neighboring peer in the Hello state
2-WayInside.ro INTEGER .1.3.6.1.4.1.4323.2.7.1.7.5.1.4 |
qbAtmPnniPeerRcvDbSumsA count of the number of Database Summary Packets received
from the neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.5 |
qbAtmPnniPeerXmtDbSumsA count of the number of Database Summary Packets
transmitted to the neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.6 |
qbAtmPnniPeerRcvPtspsA count of the number of PTSPs received from the
neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.7 |
qbAtmPnniPeerXmtPtspsA count of the number of PTSPs (re)transmitted to the
neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.8 |
qbAtmPnniPeerRcvPtseReqsA count of the number of PTSE Request packets received from
the neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.9 |
qbAtmPnniPeerXmtPtseReqsA count of the number of PTSE Request packets transmitted
to the neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.10 |
qbAtmPnniPeerRcvPtseAcksA count of the number of PTSE Ack packets received from the
neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.11 |
qbAtmPnniPeerXmtPtseAcksA count of the number of PTSE Ack packets transmitted to
the neighboring peer.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.7.5.1.12 |
qbAtmPnniNodePglTablePeer group leader election information for a PNNI node in
this switching system. SEQUENCE OF QbAtmPnniNodePglEntry .1.3.6.1.4.1.4323.2.7.1.7.6 |
qbAtmPnniNodePglEntryAn entry in the table, containing PGL election information
of a PNNI logical node in this switching system. QbAtmPnniNodePglEntry .1.3.6.1.4.1.4323.2.7.1.7.6.1 |
qbAtmPnniNodePglLeadershipPriorityThe Leadership priority value this node should advertise in
its nodal information group for the given peer group. Only
the value zero can be used with nodes that are not PGL/LGN
capable. If there is no configured parent node index or no
corresponding entry in the pnniNodeTable, then the
advertised leadership priority is zero regardless of this
value.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.6.1.1 |
qbAtmPnniNodeCfgParentNodeIndexThe local node index used to identify the node that will
represent this peer group at the next higher level of
hierarchy, if this node becomes peer group leader. The
value 0 indicates that there is no parent node.rw Integer32 .1.3.6.1.4.1.4323.2.7.1.7.6.1.2 |
qbAtmPnniNodePglInitTimeThe amount of time in seconds this node will delay
advertising its choice of preferred PGL after having
initialized operation and reached the full state with at
least one neighbor in the peer group.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.4323.2.7.1.7.6.1.3 |
qbAtmPnniNodePglOverrideDelayThe amount of time in seconds a node will wait for itself
to be declared the preferred PGL by unanimous agreement
among its peers. In the absence of unanimous agreement
this will be the amount of time that will pass before this
node considers a two thirds majority as sufficient
agreement to declare itself peer group leader, abandoning
the attempt to get unanimous agreement.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.4323.2.7.1.7.6.1.4 |
qbAtmPnniNodePglReelectTimeThe amount of time in seconds after losing connectivity to
the current peer group leader, that this node will wait
before re-starting the process of electing a new peer group
leader.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.4323.2.7.1.7.6.1.5 |
qbAtmPnniNodePglStateIndicates the state that this node is in with respect to
the Peer Group Leader election that takes place in the
node's peer group. The values are enumerated in the Peer
Group Leader State Machine.ro Enumeration .1.3.6.1.4.1.4323.2.7.1.7.6.1.6 |
qbAtmPnniNodePreferredPglThe Node ID of
the node which the local node believes should be or become
the peer group leader. This is also the value the local
node is currently advertising in the `Preferred Peer Group
Leader Node ID' field of its nodal information group within
the given peer group. If a Preferred PGL has not been
chosen, this attribute's value is set to (all) zero(s).ro QbAtmPnniNodeId .1.3.6.1.4.1.4323.2.7.1.7.6.1.7 |
qbAtmPnniNodePeerGroupLeaderThe Node Identifier of the node which is currently
operating as peer group leader of the peer group this node
belongs to. If a PGL has not been elected, this attribute's
value is set to (all) zero(s).ro QbAtmPnniNodeId .1.3.6.1.4.1.4323.2.7.1.7.6.1.8 |
qbAtmPnniNodePglTimeStampThe time at which the current Peer Group Leader established
itself.ro TimeStamp (QBSYS-SYSTEM-MIB) .1.3.6.1.4.1.4323.2.7.1.7.6.1.9 |
qbAtmPnniNodeActiveParentNodeIdThe Node Identifier value being used by the Peer Group
Leader to represent this peer group at the next higher
level of the hierarchy. If this node is at the highest
level of the hierarchy or if no PGL has yet been elected
the PNNI Protocol Entity sets the value of this attribute
to (all) zero(s).ro QbAtmPnniNodeId .1.3.6.1.4.1.4323.2.7.1.7.6.1.10 |
qbAtmPnniNodeTimerTableA table of initial PNNI timer values and significant
change thresholds. SEQUENCE OF QbAtmPnniNodeTimerEntry .1.3.6.1.4.1.4323.2.7.1.7.7 |
qbAtmPnniNodeTimerEntryAn entry in the table, containing initial PNNI timer values
and significant change thresholds of a PNNI logical node in
this switching system. QbAtmPnniNodeTimerEntry .1.3.6.1.4.1.4323.2.7.1.7.7.1 |
qbAtmPnniNodePtseHolddownThe initial value for the PTSE hold down timer that will be
used by the given node to limit the rate at which it can
re-originate PTSEs. It must be a positive non-zero number.rw Integer32 UNITS "100 milliseconds" .1.3.6.1.4.1.4323.2.7.1.7.7.1.1 |
qbAtmPnniNodeHelloHolddownThe initial value for the Hello hold down timer that will
be used by the given node to limit the rate at which it
sends Hellos. It must be a positive non-zero number.rw Integer32 UNITS "100 milliseconds" .1.3.6.1.4.1.4323.2.7.1.7.7.1.2 |
qbAtmPnniNodeHelloIntervalThe initial value for the Hello Timer.
In the absence of triggered Hellos, this node will send one
Hello packet on each of its ports on this interval.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.4323.2.7.1.7.7.1.3 |
qbAtmPnniNodeHelloInactivityFactorThe value for the Hello Inactivity factor that this
node will use to determine when a neighbor has gone down.rw Integer32 .1.3.6.1.4.1.4323.2.7.1.7.7.1.4 |
qbAtmPnniNodeHlinkInactThe amount of time a node will continue to
advertise a horizontal (logical) link for which it has
not received and processed a LGN Horizontal Link
information group.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.4323.2.7.1.7.7.1.5 |
qbAtmPnniNodePtseRefreshIntervalThe initial value for the Refresh timer that this node will
use to drive (re-)origination of PTSEs in the absence of
triggered updates.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.4323.2.7.1.7.7.1.6 |
qbAtmPnniNodePtseLifetimeFactorThe value for the lifetime multiplier, expressed as a
percentage. The result of multiplying the
qbAtmPnniNodePtseRefreshInterval attribute value by this
attribute value is used as the initial lifetime that this
node places into self-originated PTSEs.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.7.1.7 |
qbAtmPnniNodeRxmtIntervalThe period between retransmissions of unacknowledged
Database Summary packets, PTSE Request packets, and PTSPs.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.4323.2.7.1.7.7.1.8 |
qbAtmPnniNodePeerDelayedAckIntervalThe minimum amount of time between transmissions of
delayed PTSE acknowledgement packets.rw Integer32 UNITS "100 milliseconds" .1.3.6.1.4.1.4323.2.7.1.7.7.1.9 |
qbAtmPnniNodeAvcrPmThe proportional multiplier used in the algorithms that
determine significant change for AvCR parameters, expressed
as a percentage.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.7.1.10 |
qbAtmPnniNodeAvcrMtThe minimum threshold used in the algorithms that determine
significant change for AvCR parameters, expressed as a
percentage.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.7.1.11 |
qbAtmPnniNodeCdvPmThe proportional multiplier used in the algorithms that
determine significant change for CDV metrics, expressed as
a percentage.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.7.1.12 |
qbAtmPnniNodeCtdPmThe proportional multiplier used in the algorithms that
determine significant change for CTD metrics, expressed as
a percentage.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.7.7.1.13 |
qbAtmPnniLinkTableThis table contains the attributes necessary to describe
the operation of logical links attached to the local
switching system and the relationship with the neighbor
nodes on the other end of the links. Links are attached to
a specific node within the switching system. A
concatenation of the Node Index of the node within the
local switching system and the port ID are used as the
instance ID to uniquely identify the link. Links may
represent horizontal links between lowest level neighboring
peers, outside links, uplinks, or horizontal links to/from
LGNs.
The entire qbAtmPnniLink object is read-only, reflecting the
fact that this information is discovered dynamically by the
PNNI protocol rather than configured. SEQUENCE OF QbAtmPnniLinkEntry .1.3.6.1.4.1.4323.2.7.1.7.8 |
qbAtmPnniLinkEntryAn entry in the table, containing information about a link
attached to a PNNI logical node in this switching system. QbAtmPnniLinkEntry .1.3.6.1.4.1.4323.2.7.1.7.8.1 |
qbAtmPnniLinkPortIdThe Port Identifier of the link as selected by the local
node. This value has meaning only within the context of
the node to which the port is attached. Integer32 .1.3.6.1.4.1.4323.2.7.1.7.8.1.1 |
qbAtmPnniLinkTypeIndicates the type of link being described.ro Enumeration .1.3.6.1.4.1.4323.2.7.1.7.8.1.2 |
qbAtmPnniLinkHelloStateFor horizontal and outside links between lowest-level nodes
and for links of unknown type, this attribute indicates the
state of the Hello protocol exchange over this link. For
links to/from LGNs, this attribute indicates the state of
the corresponding LGN Horizontal Link Hello State Machine.
For uplinks (where the port ID is not also used for the
underlying outside link), this attribute is set to
notApplicable.ro QbAtmPnniHelloState .1.3.6.1.4.1.4323.2.7.1.7.8.1.3 |
qbAtmHiddenVclTableThe QB table with extensions to atmVclTable SEQUENCE OF QbAtmHiddenVclEntry .1.3.6.1.4.1.4323.2.7.1.8 |
qbAtmHiddenVclEntryEntry in qbAtmHiddenVclTable QbAtmHiddenVclEntry .1.3.6.1.4.1.4323.2.7.1.8.1 |
qbAtmHiddenVclNameA textual description for the SPVC name.rw DisplayString .1.3.6.1.4.1.4323.2.7.1.8.1.1 |
qbAtmHiddenVclTypeValue for the interface type.
Native ATM - Q155, S622;
non-native - E1, DS1, ENET, VTrw Enumeration .1.3.6.1.4.1.4323.2.7.1.8.1.2 |
qbAtmHiddenVclIfIndexifIndex value for IOT interface. This
value is not used for native ATM interfaces.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4323.2.7.1.8.1.3 |
qbAtmHiddenVclVtIndexAddress information for a VT card. This
value is used for VT cards only.rw INTEGER .1.3.6.1.4.1.4323.2.7.1.8.1.4 |
qbAtmSwitchModuleGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.1.9 |
qbAtmStatsBuffOverCellsThis object gives the number of cells discarded due to
buffer overflows.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.9.1 |
qbAtmStatsInvalidCellsThis object gives the number of cells discarded due to
unknown VPI/VCI.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.9.2 |
qbAtmStatsInvUpdateCellsThis object gives the number of cells discarded due to
internal switch errors.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.9.3 |
qbAtmInterfaceStatTableThe Quantum Bridge ATM Interface Statistic Table contains
ATM layer statistics for each ATM interface. SEQUENCE OF QbAtmInterfaceStatEntry .1.3.6.1.4.1.4323.2.7.1.10 |
qbAtmInterfaceStatEntryAn entry in the Quantum ATM Interface Table.
Every ATM interface contains a corresponding
entry in the table. QbAtmInterfaceStatEntry .1.3.6.1.4.1.4323.2.7.1.10.1 |
qbAtmInterfaceStatTxOAMCellsThe total number of valid OAM cells transmitted by this
atm layer interface.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.10.1.1 |
qbAtmInterfaceStatRxOAMCellsThe total number of OAS ATM cells received by this atm
layer interface.ro Counter32 .1.3.6.1.4.1.4323.2.7.1.10.1.2 |
qbAtmInBandMgtTableThe QbAtmInBandMgtTable defines in-band Management IP channels for use by ATM connections. SEQUENCE OF QbAtmInBandMgtEntry .1.3.6.1.4.1.4323.2.7.1.11 |
qbAtmInBandMgtEntryAn entry in the table, containing information about an in-band Management
channel. QbAtmInBandMgtEntry .1.3.6.1.4.1.4323.2.7.1.11.1 |
qbAtmInBandMgtIpAddrAn IP Address for in-band SNMP Management of this chassis. IpAddress .1.3.6.1.4.1.4323.2.7.1.11.1.1 |
qbAtmInBandMgtIpMaskThe IP Network Mask associated with this in-band SNMP Management IP Address.rw IpAddress .1.3.6.1.4.1.4323.2.7.1.11.1.2 |
qbAtmInBandMgtIpIfIndexThe Interface associated with this in-band management address.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.3 |
qbAtmInBandMgtNeighborIpThis is the neighbor IP address associated with the in-band Management Interface. If the
qbAtmInBandMgtConnKind is any value other than pvc(1), this object is non-applicable.rw IpAddress .1.3.6.1.4.1.4323.2.7.1.11.1.4 |
qbAtmInBandMgtIfIndexThis is the interface index associated with the in-band Management connection. If the
qbAtmInBandMgtConnKind is any value other than pvc(1), this object is non-applicable.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.5 |
qbAtmInBandMgtVpiIf the value of qbAtmInBandMgtConnKind is pvc(1), this is the VPI associated with
this in-band management connection. If the value of qbAtmInBandMgtConnKind is spvcInitiator(4),
this object is target VPI. In all other cases, the value of this object is non-applicable.rw AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.6 |
qbAtmInBandMgtVciIf the value of qbAtmInBandMgtConnKind is pvc(1), this is the VCI associated with
this in-band management connection. If the value of qbAtmInBandMgtConnKind is spvcInitiator(4),
this object is target VCI. In all other cases, the value of this object is non-applicable.rw AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.7 |
qbAtmInBandMgtConnKindThis is the connection type associated with the in-band Management connection. The currently
accepted types are pvc(1), spvcInitiator(4) and spvcTarget(5).rw AtmConnKind (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.8 |
qbAtmInBandMgtTxTdThe Transmit traffic descriptor associated with this in-band management channel.rw AtmTrafficDescrParamIndex (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.9 |
qbAtmInBandMgtRxTdThe Receive traffic descriptor associated with this in-band management channel.rw AtmTrafficDescrParamIndex (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.10 |
qbAtmInBandMgtTargetNsapAddrIf the value of qbAtmInBandMgtConnKind is spvcInitiator(4) this object
represetns the Target NSAP Address of the connection. In all other cases,
the value of this object is non-applicable.rw AtmAddr (ATM-TC-MIB) .1.3.6.1.4.1.4323.2.7.1.11.1.11 |
qbAtmInBandMgtRowStatusTo create, or delete an Entry in this table.
Setting this object to createAndGo(4) causes
the corresponding row to be created.
Setting this object to destroy(6) causes the corresponding
row to be deleted.
Note that only a single instance of a row
can be created in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4323.2.7.1.11.1.12 |
qbAtmTrafficDescriptorTypes OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.1.12 |
qbAtmPktThis traffic descriptor type is to define a connection with an Ethernet endpoint, and
it is for a user that does not want to use ATM parameters directly. The EtherNet bandwidth
will be converted to a nrtVbr traffic descriptor. The conversion from Ethernet bandwidth to
ATM cell rate must add an ATM cell tax. This is defined using the pcbe (packet-to-cell bandwidth expansion)
factor. If this is not defined for the traffic descriptor, then the system default (qbAtmDefaultPCBE)should be used.
The use of the parameter vector for this type:
Parameter 1: minbw, the minimum guarnteed bandwidth fo rthe connection. This is defined in Mb/sec. (0-100).
Parameter 2: maxbw, the maximum bursting capability of the connection. This is defined in Mb/sec (1-100).
It is default to minbw.
Parameter 3: bw, indicates the bandwidth for the PON segment. Vaules are expressed in Mb, and may take
interger value between 1 and 100. (only apply to 155Mb PON). It is default to minbw.
Parameter 4: pcbe, it defines the packed-to-cell bandwidth expansion. This is the percentage overhead that
is used to convert Ethernet bandwidth to ATM cell rates. It is default to qbAtmDefaultPCBE.
Parameter 5: not used. OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.1.12.1 |
qbAtmConformance OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.2 |
qbAtmCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.2.1 |
qbAtmGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.2.2 |
qbAtmBaseGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4323.2.7.3 |
qbAtmF4F5LLIDThis object stores Loopback Location ID (LLID).rw OCTET STRING .1.3.6.1.4.1.4323.2.7.3.1 |
qbAtmDefaultPCBEThis object stores the default atm cell tax to be used by the system.rw INTEGER .1.3.6.1.4.1.4323.2.7.3.2 |