Q-IN-Q-MIB
The structure of Q-in-Q information for the proprietary enterprise.
Main OID:
swQinQMIB.dlink-common-mgmt.57
74
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
74 total| Object Name |
|---|
swQinQMIBThe structure of Q-in-Q information for the
proprietary enterprise. MODULE-IDENTITY .dlink-common-mgmt.57 |
swQinQCtrl OBJECT IDENTIFIER .dlink-common-mgmt.57.1 |
swQinQStateThis object is used to enable/disable the Q-in-Q status.rw Enumeration .dlink-common-mgmt.57.1.1 |
swQinQInnerTpidThis object is used to set the system's inner TPID.rw OCTET STRING .dlink-common-mgmt.57.1.2 |
swQinQInfo OBJECT IDENTIFIER .dlink-common-mgmt.57.2 |
swQinQPortMgmt OBJECT IDENTIFIER .dlink-common-mgmt.57.3 |
swQinQPortTableA table that contains Q-in-Q VLAN mode information about each port. SEQUENCE OF SwQinQPortEntry .dlink-common-mgmt.57.3.1 |
swQinQPortEntryA list of Q-in-Q VLAN mode information for each port. SwQinQPortEntry .dlink-common-mgmt.57.3.1.1 |
swQinQPortIndexThis object indicates the module's port number.ro INTEGER .dlink-common-mgmt.57.3.1.1.1 |
swQinQPortRoleThis object sets the port role in Q-in-Q mode. It can be
UNI port or NNI port.rw Enumeration .dlink-common-mgmt.57.3.1.1.2 |
swQinQPortMissDropThis object is used to enable/disable C-VLAN based SP-VLAN assignment miss drop.
If missdrop is enabled, the packet that does not match any assignment rule in
the Q-in-Q profile will be dropped.
If missdrop is disabled, then the packet will be assigned to the PVID of the
received port.rw Enumeration .dlink-common-mgmt.57.3.1.1.3 |
swQinQPortTpidSpecifies the outer TPID for each port.rw OCTET STRING .dlink-common-mgmt.57.3.1.1.4 |
swQinQPortUseInnerPriorityThis object specifies whether to use the priority in the C-VLAN
tag as the priority in the SP-VLAN tag.rw Enumeration .dlink-common-mgmt.57.3.1.1.5 |
swQinQPortInnerTagStateSpecifies whether to add inner tag for ingress untagged packets.rw Enumeration .dlink-common-mgmt.57.3.1.1.6 |
swQinQPortInnerTagIf swQinQPortInnerTagState is enabled, this object specifies the inner tag.rw OCTET STRING .dlink-common-mgmt.57.3.1.1.7 |
swQinQPortTrustCVIDIf swQinQState is enabled, this object specifies whether to use the C-VID
of the ingress packet to get S-VID on the UNI port or not.rw Enumeration .dlink-common-mgmt.57.3.1.1.8 |
swQinQPortVlanTranslationIf swQinQState and swQinQPortTrustCVID are enabled, this object specifies
whether to lookup VLAN translation table to get S-VID by the C-VID of
the ingress packet on the UNI port or not.rw Enumeration .dlink-common-mgmt.57.3.1.1.9 |
swQinQPortInnerTpidSpecifies the inner TPID for each port.rw OCTET STRING .dlink-common-mgmt.57.3.1.1.10 |
swQinQPortRuleTableA table that is used to configure a port's Q-in-Q SP-VLAN assignment rule. SEQUENCE OF SwQinQPortRuleEntry .dlink-common-mgmt.57.3.2 |
swQinQPortRuleEntryA list of Q-in-Q SP-VLAN assignment rules for each port. SwQinQPortRuleEntry .dlink-common-mgmt.57.3.2.1 |
swQinQPortRuleIndexThis object indicates the module's port number.ro INTEGER .dlink-common-mgmt.57.3.2.1.1 |
swQinQProfileIdThis object indicates the Q-in-Q profile ID.ro INTEGER .dlink-common-mgmt.57.3.2.1.2 |
swQinQPortRuleRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .dlink-common-mgmt.57.3.2.1.3 |
swVlanTranslateTableA table that contains VLAN translation information. SEQUENCE OF SwVlanTranslateEntry .dlink-common-mgmt.57.3.3 |
swVlanTranslateEntryA list of VLAN translation information. SwVlanTranslateEntry .dlink-common-mgmt.57.3.3.1 |
swVlanTranslatePortIndexThis object indicates the module's port number.ro INTEGER .dlink-common-mgmt.57.3.3.1.1 |
swVlanTranslateCVIDThe customer VLAN identifier in a C-TAG.ro VlanId .dlink-common-mgmt.57.3.3.1.2 |
swVlanTranslateSVIDA VLAN identifier conveyed in an S-TAG.rw VlanId .dlink-common-mgmt.57.3.3.1.3 |
swVlanTranslateSVIDOperationThe 'add' action indicates to add a tag for the assigned SP-VLAN
before the C-VLAN tag. If there is S-TAG in the packet, this rule
will not take effect.
The 'replace' action indicates to replace the C-VLAN in the tag by
the SP-VLAN. If there is no C-TAG in the packet, this rule will not
take effect.rw Enumeration .dlink-common-mgmt.57.3.3.1.4 |
swVlanTranslatePriorityThe priority of the S-TAG.
-1 is default value.rw INTEGER (-1|0..7) .dlink-common-mgmt.57.3.3.1.5 |
swVlanTranslateRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .dlink-common-mgmt.57.3.3.1.6 |
swDoubleVlanTranslateTableA table that contains Double Tag VLAN translation information. SEQUENCE OF SwDoubleVlanTranslateEntry .dlink-common-mgmt.57.3.4 |
swDoubleVlanTranslateEntryA list of Double Tag VLAN translation information
, only work on NNI port. SwDoubleVlanTranslateEntry .dlink-common-mgmt.57.3.4.1 |
swDoubleVlanTranslatePortIndexThis object indicates the module's port number. INTEGER .dlink-common-mgmt.57.3.4.1.1 |
swDoubleVlanTranslateSVIDThe customer VLAN identifier in a S-TAG. VlanId .dlink-common-mgmt.57.3.4.1.2 |
swDoubleVlanTranslateCVIDThe customer VLAN identifier in a C-TAG. VlanId .dlink-common-mgmt.57.3.4.1.3 |
swDoubleVlanTranslateOperationThe 'replace' action indicates to replace the S-VLAN in the tag by
the New S-VLAN.rw Enumeration .dlink-common-mgmt.57.3.4.1.4 |
swDoubleVlanTranslateNewSVIDThe SP-VLAN identifier used to replace.rw VlanId .dlink-common-mgmt.57.3.4.1.5 |
swDoubleVlanTranslatePriorityThe priority of the S-TAG.
-1 is default value.rw INTEGER (-1|0..7) .dlink-common-mgmt.57.3.4.1.6 |
swDoubleVlanTranslateRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .dlink-common-mgmt.57.3.4.1.7 |
swQinQMgmt OBJECT IDENTIFIER .dlink-common-mgmt.57.4 |
swQinQProfileTableThis table is used to create a Q-in-Q profile to assign SP-VLAN.
Multiple rules can be specified for a Q-in-Q profile. SEQUENCE OF SwQinQProfileEntry .dlink-common-mgmt.57.4.1 |
swQinQProfileEntryA list containing Q-in-Q profile information. SwQinQProfileEntry .dlink-common-mgmt.57.4.1.1 |
swQinQProfileIDSpecifies the Q-in-Q profile ID.ro INTEGER .dlink-common-mgmt.57.4.1.1.1 |
swQinQProfileRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .dlink-common-mgmt.57.4.1.1.2 |
swQinQRuleTableThis table contains Q-in-Q rule information. These rules will
indicate whether to add a tag for the SP-VLAN or to replace the
inner C-VLAN in the tag by the SP-VLAN. If the matched packet
has a SP-VLAN tag and the action is 'add', this rule will not
take effect for the packet. If the matched packet has no C-VLAN
tag and the action is 'replace', this rule will not take effect too.
C-VLAN based Q-in-Q rules have lower priority than flow-based Q-in-Q rules.
For flow-based Q-in-Q rules in the same profile, the rule's priority is
decided by the rule's ID; a smaller ID has a higher priority. SEQUENCE OF SwQinQRuleEntry .dlink-common-mgmt.57.4.2 |
swQinQRuleEntryA list of information about Q-in-Q rules. SwQinQRuleEntry .dlink-common-mgmt.57.4.2.1 |
swQinQRuleProfileIDSpecifies the profile ID.ro INTEGER .dlink-common-mgmt.57.4.2.1.1 |
swQinQRuleAccessIDSpecifies the ID of the Q-in-Q rule entry related to the swQinQRuleProfileID.ro INTEGER .dlink-common-mgmt.57.4.2.1.2 |
swQinQRuleClassifySrcMacAddrSpecifies the source MAC address.rw MacAddress (SNMPv2-TC) .dlink-common-mgmt.57.4.2.1.3 |
swQinQRuleClassifySrcMacAddrMaskSpecifies the source MAC address mask.rw MacAddress (SNMPv2-TC) .dlink-common-mgmt.57.4.2.1.4 |
swQinQRuleClassifyDstMacAddrSpecifies the destination MAC address.rw MacAddress (SNMPv2-TC) .dlink-common-mgmt.57.4.2.1.5 |
swQinQRuleClassifyDstMacAddrMaskSpecifies the destination MAC address mask.rw MacAddress (SNMPv2-TC) .dlink-common-mgmt.57.4.2.1.6 |
swQinQRuleSrcIPv4AddressSpecifies an IPv4 source address.rw IpAddress .dlink-common-mgmt.57.4.2.1.7 |
swQinQRuleSrcIPv4AddrMaskSpecifies the IPv4 source address mask.rw IpAddress .dlink-common-mgmt.57.4.2.1.8 |
swQinQRuleDstIPv4AddressSpecifies an IPv4 destination address.rw IpAddress .dlink-common-mgmt.57.4.2.1.9 |
swQinQRuleDstIPv4AddrMaskSpecifies the IPv4 destination address mask.rw IpAddress .dlink-common-mgmt.57.4.2.1.10 |
swQinQRuleInnerVidSpecifies the packet's inner VID range.rw DisplayString (SNMPv2-TC) .dlink-common-mgmt.57.4.2.1.11 |
swQinQRuleOuterVidSpecifies the packet's outer VID range.rw DisplayString (SNMPv2-TC) .dlink-common-mgmt.57.4.2.1.12 |
swQinQRule8021pSpecifies the packet's 802.1p priority.
-1 means the 802.1p priority is not setrw INTEGER(-1|0..7) .dlink-common-mgmt.57.4.2.1.13 |
swQinQRuleIpProtocolSpecifies the IP protocol.rw INTEGER .dlink-common-mgmt.57.4.2.1.14 |
swQinQRuleSourcePortSpecifies the source port number.rw INTEGER .dlink-common-mgmt.57.4.2.1.15 |
swQinQRuleDestinationPortSpecifies the destination port number.rw INTEGER .dlink-common-mgmt.57.4.2.1.16 |
swQinQRuleSpvidOperationThe 'add' action indicates to add a tag for the assigned SP-VLAN
before the C-VLAN tag. If there is S-TAG in the packet, this rule
will not take effect.
The 'replace' action indicates to replace the C-VLAN in the tag by
the SP-VLAN. If there is no C-TAG in the packet, this rule will not
take effect.rw Enumeration .dlink-common-mgmt.57.4.2.1.17 |
swQinQRuleSpvidSpecifies the SP-VLAN ID to be assigned to the matched packet.rw INTEGER .dlink-common-mgmt.57.4.2.1.18 |
swQinQPrioritySpecifies the priority of the SP-VLAN.
-1 is default value.rw INTEGER(-1|0..7) .dlink-common-mgmt.57.4.2.1.19 |
swQinQRuleRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .dlink-common-mgmt.57.4.2.1.20 |
swQinQRuleActivePortSpecifies the active port list which the rule takes effect.ro PortList (Q-BRIDGE-MIB) .dlink-common-mgmt.57.4.2.1.21 |
swVlanTranslationCVIDTableA table that contains VLAN translation information applied in enabling
port's swQinQPortVlanTranslation, swQinQPortTrustCVID and QinQ. SEQUENCE OF SwVlanTranslationCVIDEntry .dlink-common-mgmt.57.4.3 |
swVlanTranslationCVIDEntryA list of VLAN translation information applied in enabling a
port's swQinQPortVlanTranslation, swQinQPortTrustCVID and QinQ. SwVlanTranslationCVIDEntry .dlink-common-mgmt.57.4.3.1 |
swVlanTranslationCVIDThe customer VLAN identifier in a C-TAG.ro VlanId .dlink-common-mgmt.57.4.3.1.1 |
swVlanTranslationSVIDA VLAN identifier conveyed in an S-TAG.rw VlanId .dlink-common-mgmt.57.4.3.1.2 |
swVlanTranslationSVIDOperationThe 'add' action indicates to add a tag for the assigned SP-VLAN
before the C-VLAN tag. If there is S-TAG in the packet, this rule
will not take effect.
The 'replace' action indicates to replace the C-VLAN in the tag by
the SP-VLAN. If there is no C-TAG in the packet, this rule will not
take effect.rw Enumeration .dlink-common-mgmt.57.4.3.1.3 |
swVlanTranslationCVIDRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .dlink-common-mgmt.57.4.3.1.4 |
More MIBs from Default
Browse all DefaultMIBs →RC-TLS-MIB
SNMP MIB module
2614 objects→
AVAYA-WLAN-MIB
The AVAYA-WLAN-MIB provides SNMP-based management and monitoring capabilities for Avaya wireless LAN infrastructure, enabling the collection of performance metrics such as access point status, client association counts, signal strength, and radio interface statistics. This module facilitates the tracking of WLAN-specific events and configuration parameters to support network availability and troubleshooting within Avaya wireless deployments.
2022 objects→
VMWARE-NSX-MIB
The VMWARE-NSX-MIB enables SNMP-based monitoring and management of VMware NSX-T Data Center virtual network infrastructure, exposing metrics for logical switches, routers, distributed firewalls, and overlay tunnel states. It facilitates the tracking of Layer 2 through Layer 7 service instances, including access control lists, Quality of Service policies, and virtual network topology changes within the software-defined networking environment.
1035 objects→
923switch.m
Standard SNMP MIB module defining data structures for 923switch.m.
999 objects→
CTATX-MIB
Standard SNMP MIB module defining data structures for CTATX-MIB.
747 objects→
DC-BGP-MIB
SNMP MIB module
652 objects→