PT-RADIOLINK-MIB
AI MIB Summary
The PT-RADIOLINK-MIB module enables the monitoring and management of PT (PT Telecom) proprietary radio link hardware, specifically exposing performance metrics such as link status, signal strength, error counters, and interface utilization for point-to-point microwave or wireless backhaul systems.
This is the MIB for Radio Link specifics in PT
Main OID:
ptRadioLink.1.3.6.1.4.1.18086.7
130
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
130 total| Object Name |
|---|
ptRadioLinkThis is the MIB for Radio Link specifics in PT MODULE-IDENTITY .1.3.6.1.4.1.18086.7 |
ctTableA table of CT Table entries. SEQUENCE OF CtEntry .1.3.6.1.4.1.18086.7.1 |
ctEntryAn entry of CT application. CtEntry .1.3.6.1.4.1.18086.7.1.1 |
actualInputPowerActual input power of the CT in dBmro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.1 |
actualOutputPowerActual output power of the CT in dBmro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.2 |
actualRxAcmActual rx modulation and codingro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.3 |
actualTxAcmActual tx modulation and codingro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.4 |
ctDistinguishedNameUnique id/name of the carrier termination, according to FDN (rack/slot/port/class)ro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.5 |
descriptionUser description of the carrior termination.rw OCTET STRING .1.3.6.1.4.1.18086.7.1.1.6 |
carrierIdId of the carrier. (A, B, C, D) Used in XPIC & MIMO configurations to check that the carrier termination is connected to the correct far end carrier termination. Should be the same id on both sides of the hop. Defaulted when not MIMO or XPIC. Sometimes also referred to as preamblerw Enumeration .1.3.6.1.4.1.18086.7.1.1.7 |
ctStatusThe status of the carrier termination, hopro Enumeration .1.3.6.1.4.1.18086.7.1.1.8 |
frameIdA unique identifier for the radio frame to be used. Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.rw Integer32 .1.3.6.1.4.1.18086.7.1.1.9 |
txFrequencySelected frequency on the transmitter (kHz). Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.rw Integer32 .1.3.6.1.4.1.18086.7.1.1.10 |
minTxFrequencyMinimum Tx frequency possible to use, given by the selected frame-idro Integer32 .1.3.6.1.4.1.18086.7.1.1.11 |
maxTxFrequencyMaximum Tx frequency possible to use, given by the selected frame-idro Integer32 .1.3.6.1.4.1.18086.7.1.1.12 |
rxFrequencySelected frequency on the receiver (kHz). Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.rw Integer32 .1.3.6.1.4.1.18086.7.1.1.13 |
minRxFrequencyMinimum Rx frequency possible to use, given by the selected frame-idro Integer32 .1.3.6.1.4.1.18086.7.1.1.14 |
maxRxFrequencyMaximum Rx frequency possible to use, given by the selected frame-idro Integer32 .1.3.6.1.4.1.18086.7.1.1.15 |
frequencyStepSizeFrequency step size in kHzro Integer32 .1.3.6.1.4.1.18086.7.1.1.16 |
duplexDistanceDistance between Tx and Rx frequencies (kHz)ro Integer32 .1.3.6.1.4.1.18086.7.1.1.17 |
duplexTypeThe duplex type is given by the equipment (Fixed,Variable)ro Enumeration .1.3.6.1.4.1.18086.7.1.1.18 |
duplexConfigEnabling or disabling configuration of Rx freq using duplex distancerw EnableStatusTC .1.3.6.1.4.1.18086.7.1.1.19 |
autoFreqSelectionAutomatic frequency selection moderw Enumeration .1.3.6.1.4.1.18086.7.1.1.20 |
autoFreqSelectedChannelAutomatic frequency selected channelrw Integer32 .1.3.6.1.4.1.18086.7.1.1.21 |
autoFreqSelectionStatusAutomatic frequency statusro Enumeration .1.3.6.1.4.1.18086.7.1.1.22 |
channelSpacingChannel spacingro Enumeration .1.3.6.1.4.1.18086.7.1.1.23 |
polarizationAntenna polarizationrw Enumeration .1.3.6.1.4.1.18086.7.1.1.24 |
txOperStatusOperative status of the transmitterro Enumeration .1.3.6.1.4.1.18086.7.1.1.25 |
txAdminStatusAdministrative status of the transmitterrw Enumeration .1.3.6.1.4.1.18086.7.1.1.26 |
selectedOutputPowerTypeSelected output power typerw Enumeration .1.3.6.1.4.1.18086.7.1.1.27 |
availableOutputPowerTypeAvailable output power typerw Enumeration .1.3.6.1.4.1.18086.7.1.1.28 |
selectedMinOutputPowerSelected min output power. Selected min & max output power should be set to the same value for RTPC mode, otherwise the hop operates in ATPC mode.rw Integer32 .1.3.6.1.4.1.18086.7.1.1.29 |
selectedMaxOutputPowerSelected max output power. Selected min & max output power should be set to the same value for RTPC mode, otherwise the hop operates in ATPC mode.rw Integer32 .1.3.6.1.4.1.18086.7.1.1.30 |
availableMinOutputPowerThe minimum output power supported (dBm). The system shows a value if the equipment is available and a frame id has been selected.ro Integer32 .1.3.6.1.4.1.18086.7.1.1.31 |
availableMaxOutputPowerThe maximum output power supported (dBm). The system shows a value if the equipment is available and a frame id has been selected.ro Integer32 .1.3.6.1.4.1.18086.7.1.1.32 |
referenceSecEach modulation is compliant to a Reference Spectrum Efficiency Class (RSEC). When running Adaptive Coding/Modulation, one SEC has to be selected for all the coding/modulations between selectedMinACM and selectedMaxACM. This parameter is called Reference SEC. This setting will affect availableMaxOutputPower, in order to fulfill spectrum requirements. Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.rw Enumeration .1.3.6.1.4.1.18086.7.1.1.33 |
targetInputPowerFarEndThe wanted input power at far end (dBm), when running ATPCrw Integer32 .1.3.6.1.4.1.18086.7.1.1.34 |
berAlarmThresholdThreshold for the BER alarmrw Enumeration .1.3.6.1.4.1.18086.7.1.1.35 |
inputPowerAlarmThresholdThreshold for the input power alarmrw Integer32 .1.3.6.1.4.1.18086.7.1.1.36 |
plannedAlignmentInputPowerThe planned received input power (dBm) dependent upon selected minimum ACM and corresponding output power. Used when doing alignmentrw Integer32 .1.3.6.1.4.1.18086.7.1.1.37 |
atpcFallbackEnable or disable the output power fall back functionrw EnableStatusTC .1.3.6.1.4.1.18086.7.1.1.38 |
atpcFallbackTimerSpecifies the timer for output power fall back (# of seconds)rw Integer32 .1.3.6.1.4.1.18086.7.1.1.39 |
atpcFallbackOutputPowerThe ATPC fallback output powerrw Integer32 .1.3.6.1.4.1.18086.7.1.1.40 |
xpicStatusStatus of the XPIC function.ro XpicMimoTC .1.3.6.1.4.1.18086.7.1.1.41 |
mimoStatusStatus of the MIMO function.ro XpicMimoTC .1.3.6.1.4.1.18086.7.1.1.42 |
actualSnirActual signal to noise plus interference ratio (dB).ro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.43 |
actualXpiThe carrier to cross-polar interference level (dBc).ro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.44 |
actualSiSpatial interference between the CTs when MIMO is configured.ro OCTET STRING .1.3.6.1.4.1.18086.7.1.1.45 |
actualTxCapacityActual capacity supported by the carrier termination.ro Integer32 .1.3.6.1.4.1.18086.7.1.1.46 |
licensedCapacityWanted or installed license for the capacity allowed for the carrier termination.ro Integer32 .1.3.6.1.4.1.18086.7.1.1.47 |
availableMinCapacityMinimum capacity possible to use. Given by the selected frame-id (kbit/s)ro Integer32 .1.3.6.1.4.1.18086.7.1.1.48 |
availableMaxCapacityMaximum capacity possible to use. Given by the selected frame-id (kbit/s)ro Integer32 .1.3.6.1.4.1.18086.7.1.1.49 |
selectedMinCapacitySelected minimum capacity, derived from selected minimum ACM (kbit/s)ro Integer32 .1.3.6.1.4.1.18086.7.1.1.50 |
selectedMaxCapacitySelected maximum capacity, derived from selected maximum ACM (kbit/s)ro Integer32 .1.3.6.1.4.1.18086.7.1.1.51 |
wantedLicensedCapacityWanted licensed capacity and creation of LRF for the carrier termination (kbit/s)rw Integer32 .1.3.6.1.4.1.18086.7.1.1.52 |
availableMinAcmMinimum ACM possible to use, given by the selected frame id.ro AcmTC .1.3.6.1.4.1.18086.7.1.1.53 |
availableMaxAcmMaximum ACM possible to use, given by the selected frame idro AcmTC .1.3.6.1.4.1.18086.7.1.1.54 |
selectedMinAcmSelected minimum coding/modulation. If selectedMinACM = selectedMaxACM, then the modulation is fixedrw AcmTC .1.3.6.1.4.1.18086.7.1.1.55 |
selectedMaxAcmSelected maximum coding/modulation. If selectedMinACM = selectedMaxACM, then the modulation is fixedrw AcmTC .1.3.6.1.4.1.18086.7.1.1.56 |
actualRxAcmTCActual rx modulation and codingro AcmTC .1.3.6.1.4.1.18086.7.1.1.57 |
actualTxAcmTCActual tx modulation and codingro AcmTC .1.3.6.1.4.1.18086.7.1.1.58 |
alignmentModeEnable or disable the alignment moderw EnableStatusTC .1.3.6.1.4.1.18086.7.1.1.59 |
rfLoopEnable or disable the rf looprw EnableStatusTC .1.3.6.1.4.1.18086.7.1.1.60 |
ptRadioLinkConformance OBJECT IDENTIFIER .1.3.6.1.4.1.18086.7.2 |
ptRadioLinkCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.18086.7.2.1 |
ptRadioLinkFullComplianceThe compliance statement for SNMP entities which implement everything. Unknown .1.3.6.1.4.1.18086.7.2.1.1 |
ptRadioLinkGroups OBJECT IDENTIFIER .1.3.6.1.4.1.18086.7.2.2 |
ptRadioLinkCompleteGroupA collection of all current objects in this MIB module. Unknown .1.3.6.1.4.1.18086.7.2.2.1 |
rltTableA table of RLT Table entries. SEQUENCE OF RltEntry .1.3.6.1.4.1.18086.7.3 |
rltEntryAn entry of RLT application. RltEntry .1.3.6.1.4.1.18086.7.3.1 |
rltDistinguishedNameUnique id/name of the radio link termination, according to FDN (rack/slot/port/class)ro OCTET STRING .1.3.6.1.4.1.18086.7.3.1.1 |
neIpAddressNE IP addressro IpAddress .1.3.6.1.4.1.18086.7.3.1.2 |
neIpv6AddressNE IP V6 addressro InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.18086.7.3.1.3 |
neNameNE Namero OCTET STRING .1.3.6.1.4.1.18086.7.3.1.4 |
neTypeNE Typero Enumeration .1.3.6.1.4.1.18086.7.3.1.5 |
idUser defined id of the radio link terminalrw OCTET STRING .1.3.6.1.4.1.18086.7.3.1.6 |
rltStatusThe status of the radio link terminalro Enumeration .1.3.6.1.4.1.18086.7.3.1.7 |
modeThe status of the radio link terminalrw Enumeration .1.3.6.1.4.1.18086.7.3.1.8 |
actualTxTotalCapacityActual aggregated total (packet + TDM) transmitter capacity for the radio link termination. Limited by licenses & configuration (=nearEndLimitedCapacity) and depending on actual modulation/coding used at the moment.ro Integer32 .1.3.6.1.4.1.18086.7.3.1.9 |
limitedTotalCapacityMaximum total capacity allowed by the current configuration and installed licenses. Aggregated from the constituent carrier termination values.ro Integer32 .1.3.6.1.4.1.18086.7.3.1.10 |
protectionStatusStatus of a protected node.ro Enumeration .1.3.6.1.4.1.18086.7.3.1.11 |
revertiveWaitToRestoreThe time, in number of seconds, to wait before switching back to the preferred Tx.rw Integer32 .1.3.6.1.4.1.18086.7.3.1.12 |
revertivePreferredTxThe preferred carrier termination transmitter.rw Enumeration .1.3.6.1.4.1.18086.7.3.1.13 |
protectionSwitchMode.The mode in which the switching mechanism is configuredrw Enumeration .1.3.6.1.4.1.18086.7.3.1.14 |
fadeNotificationTimerNotification is sent if fading is longer than this timer, applicable for protection.rw Integer32 .1.3.6.1.4.1.18086.7.3.1.15 |
expectedFarEndIdExpected id of far-end terminalrw OCTET STRING .1.3.6.1.4.1.18086.7.3.1.16 |
farEndIdCheckEnabling of far end id check.rw Enumeration .1.3.6.1.4.1.18086.7.3.1.17 |
cpriModeSet the mode of the CPRI front-haul product.rw Enumeration .1.3.6.1.4.1.18086.7.3.1.18 |
cpriStatusThe status of the CPRI front-haul product.ro Enumeration .1.3.6.1.4.1.18086.7.3.1.19 |
manualSwitchManual switch of protected carrier termination transmitter.rw Enumeration .1.3.6.1.4.1.18086.7.3.1.20 |
mlhcOperStatusOperative status of multi layer header compression.ro Enumeration .1.3.6.1.4.1.18086.7.3.1.21 |
mlhcAdminStatusAdministrative status of multi layer header compression.rw Enumeration .1.3.6.1.4.1.18086.7.3.1.22 |
mlhcMplsConfigMLHC/MPLS configuration.rw Enumeration .1.3.6.1.4.1.18086.7.3.1.23 |
plcOperStatusOperative status of payload compression.ro Enumeration .1.3.6.1.4.1.18086.7.3.1.24 |
plcAdminStatusAdministrative status of payload compression.rw Enumeration .1.3.6.1.4.1.18086.7.3.1.25 |
ctPerformance OBJECT IDENTIFIER .1.3.6.1.4.1.18086.7.4 |
ctG826ContinuousTableA table of CT G826 Performance Continuous counters entries. The counters are reset by ctG826Reset SEQUENCE OF CtG826ContinuousEntry .1.3.6.1.4.1.18086.7.4.1 |
ctG826ContinuousEntryAn entry of CT G826 Performance Continuous counters. CtG826ContinuousEntry .1.3.6.1.4.1.18086.7.4.1.1 |
ctG826TimeElapsedTime elapsed in seconds since last PMResetro Counter32 .1.3.6.1.4.1.18086.7.4.1.1.1 |
ctBBEBackground Block Errorsro Counter32 .1.3.6.1.4.1.18086.7.4.1.1.2 |
ctBBERBackground Block Errors Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.1.1.3 |
ctESError secondsro Counter32 .1.3.6.1.4.1.18086.7.4.1.1.4 |
ctESRError seconds Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.1.1.5 |
ctSESSeverely error secondsro Counter32 .1.3.6.1.4.1.18086.7.4.1.1.6 |
ctSESRSeverely error seconds Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.1.1.7 |
ctBBBackground blocksro OCTET STRING .1.3.6.1.4.1.18086.7.4.1.1.8 |
ctUASUnavailable secondsro Counter32 .1.3.6.1.4.1.18086.7.4.1.1.9 |
ctG826ResetReset the continuous PM countersrw Enumeration .1.3.6.1.4.1.18086.7.4.1.1.10 |
ctG826Current15mTableA table of CT Performance G826 15 m current counters Table entries. SEQUENCE OF CtG826Current15mEntry .1.3.6.1.4.1.18086.7.4.2 |
ctG826Current15mEntryAn entry of CT Performance G826 15 m current Table counters. CtG826Current15mEntry .1.3.6.1.4.1.18086.7.4.2.1 |
ctG826Current15mTimeElapsedTime elapsed in seconds since last PMResetro Counter32 .1.3.6.1.4.1.18086.7.4.2.1.1 |
ctCurrent15mBBEBackground Block Errorsro Counter32 .1.3.6.1.4.1.18086.7.4.2.1.2 |
ctCurrent15mBBERBackground Block Errors Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.2.1.3 |
ctCurrent15mESError secondsro Counter32 .1.3.6.1.4.1.18086.7.4.2.1.4 |
ctCurrent15mESRError seconds Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.2.1.5 |
ctCurrent15mSESSeverely error secondsro Counter32 .1.3.6.1.4.1.18086.7.4.2.1.6 |
ctCurrent15mSESRSeverely error seconds Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.2.1.7 |
ctCurrent15mBBBackground blocksro Counter32 .1.3.6.1.4.1.18086.7.4.2.1.8 |
ctCurrent15mUASUnavailable secondsro Counter32 .1.3.6.1.4.1.18086.7.4.2.1.9 |
ctG826Current24hTableA table of CT Performance G826 Current 24h counters entries. SEQUENCE OF CtG826Current24hEntry .1.3.6.1.4.1.18086.7.4.3 |
ctG826Current24hEntryAn entry of CT Performance G826 Current 24 h counters. CtG826Current24hEntry .1.3.6.1.4.1.18086.7.4.3.1 |
ctG826Current24hTimeElapsedTime elapsed in seconds since last PMResetro Counter32 .1.3.6.1.4.1.18086.7.4.3.1.1 |
ctCurrent24hBBEBackground Block Errorsro Counter32 .1.3.6.1.4.1.18086.7.4.3.1.2 |
ctCurrent24hBBERBackground Block Errors Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.3.1.3 |
ctCurrent24hESError secondsro Counter32 .1.3.6.1.4.1.18086.7.4.3.1.4 |
ctCurrent24hESRError seconds Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.3.1.5 |
ctCurrent24hSESSeverely error secondsro Counter32 .1.3.6.1.4.1.18086.7.4.3.1.6 |
ctCurrent24hSESRSeverely error seconds Ratioro OCTET STRING .1.3.6.1.4.1.18086.7.4.3.1.7 |
ctCurrent24hBBBackground blocksro Counter32 .1.3.6.1.4.1.18086.7.4.3.1.8 |
ctCurrent24hUASUnavailable secondsro Counter32 .1.3.6.1.4.1.18086.7.4.3.1.9 |