PRVT-EPS-MIB
Private MIB supporting Linear Ethernet Protection Switching (ITU-T G.8031)
Main OID:
prvtEpsMib.1.3.6.1.4.1.6321.1.2.3.2.10.132
47
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
47 total| Object Name |
|---|
prvtEpsMibPrivate MIB supporting Linear Ethernet Protection Switching (ITU-T G.8031) MODULE-IDENTITY .1.3.6.1.4.1.6321.1.2.3.2.10.132 |
prvtEpsMibNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.2.10.132.0 |
prvtEpsDefectAlarm1. EPS service is either operational or not operational;
2. Failure of protocol defects. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.1 |
prvtEpsSwitchoverAlarmThe alarm is issued if the active link is changed,
pointing to the path where the switchover occured. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.2 |
prvtEpsLostCommunicationThe alarm is issued in case of non reception of APS frames
in three consecutive intervals each representing 5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.3 |
prvtEpsRestoredCommunicationAPS frames are received normally after APS communication failure. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.4 |
prvtEpsSignalFailDetectedThe alarm is issued in case of CCMs are not received
and (3.5 * CCMtime(CCMinterval)) has expired. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.5 |
prvtEpsSignalDegradeDetectedThe alarm is issued in case of monitored error threshold is crossed:
1W Jitter error,
2W Jitter error,
Latency error,
Frame loss error. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.6 |
prvtEpsProtctSignalFailDetectedThe alarm is issued in case of CCMs are not received on the protected link
and (3.5 * CCMtime(CCMinterval)) has expired or the protected link is down. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.7 |
prvtEpsSignalFailRecoveryThe alarm is issued in case of CCMs start to be received
correctly again after a prvtEpsSignalFailDetected alarm occured
and (3.5 * CCMtime(CCMinterval)) timer no longer expires or the link is up . NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.8 |
prvtEpsSignalDegradeRecoveryThe alarm is issued in case of monitored error threshold is crossed bellow limis:
1W Jitter error,
2W Jitter error,
Latency error,
Frame loss error. NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.9 |
prvtEpsProtctSignalFailRecoveryThe alarm is issued in case of CCMs start to be received correctly again
on the protected link after a prvtEpsProtctSignalFailDetected alarm occured
and (3.5 * CCMtime(CCMinterval)) timer no longer expires or the link is up . NOTIFICATION-TYPE .1.3.6.1.4.1.6321.1.2.3.2.10.132.0.10 |
prvtEpsMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.2.10.132.1 |
prvtEpsService OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1 |
prvtEpsServiceTableThe table contains Ethernet Protection Switching services information. SEQUENCE OF PrvtEpsServiceEntry .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1 |
prvtEpsServiceEntryEthernet Protection Switching information about a specific service. PrvtEpsServiceEntry .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1 |
prvtEpsSvcIdThe service ID.ro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.1 |
prvtEpsServiceCfmMdLevelValue of the CFM MD level where the protected domain is situated.rw Dot1agCfmMDLevelOrNone .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.2 |
prvtEpsServicePrimaryLocalCfmMepPrimary local CFM MEP Id.rw Dot1agCfmMepIdOrZero .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.3 |
prvtEpsServicePrimaryRemoteCfmMepPrimary remote CFM MEP Id.rw Dot1agCfmMepIdOrZero .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.4 |
prvtEpsServiceSecondaryLocalCfmMepBackup local CFM MEP Id.rw Dot1agCfmMepIdOrZero .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.5 |
prvtEpsServiceSecondaryRemoteCfmMepBackup remote CFM MEP Id.rw Dot1agCfmMepIdOrZero .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.6 |
prvtEpsServiceLocalStateProtection state of the local side. The values can be set:
rsManualSwitch(7), rsClear(6) or rsLockoutOfProtection(15).
The values can be get:
rsNoRequest (0),
rsDoNotRevert (1),
rsReverseRequest (2),
rsExercise (4),
rsWaitToRestore (5),
rsClear (6),
rsManualSwitch (7),
rsSignalDegrade (9),
rsSignalFail (11),
rsForcedSwitch (13),
rsSignalFailForProtection (14),
rsLockoutOfProtection (15).rw PrvtEpsRequestStateType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.7 |
prvtEpsServiceHoldOffTimerValue of the Hold Off timer in msec (increments of 100msec).rw Unsigned32 .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.8 |
prvtEpsServiceWaitToRestoreTimerValue of the Wait To Restore timer in seconds (0 to disable it).rw Unsigned32 (0|5..12) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.9 |
prvtEpsServiceApsChannelActive APS communication.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.10 |
prvtEpsServiceProtectionType of protection (1+1 or 1:1).ro PrvtEpsProtectionType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.11 |
prvtEpsServiceDirectionType of protection (unidirectional or bidirectional).ro PrvtEpsDirectionType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.12 |
prvtEpsServiceRevertiveProtection type (revertive or non-revertive).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.13 |
prvtEpsServiceActivePathProtected service active path.ro PrvtEpsActivePathType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.14 |
prvtEpsServiceDegradeTestTypeType of test used for monitoring signal degrade situations.rw PrvtEpsMonitoringType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.15 |
prvtEpsServiceDegradeTestOwnerOwner of the SAA test used for monitoring.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.16 |
prvtEpsServiceDegradeTestNameName of the CFM or SAA test used for monitoring.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.17 |
prvtEpsServiceDegradeTestEnableStart/stop CFM or SAA test for performance monitoring.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.18 |
prvtEpsServiceDefectFopDefects noticed by APS protocol could be either none or a composition of the bits (0-3):
fullyIncompatibleProvisioning(0) - occures by the reception of three APS frames with the
incompatible 'B' bit value during the period of 22.5 seconds;
protectionSwitchingIncomplete(1) - occures if the transmitted 'Requested Signal' and the
received 'Bridged Signal' do not match for a period of 50ms or longer;
protectionConfigurationMismatch(2) - working/protection configuration mismatch, occures by
the reception of three APS frames from the working transport entity during the period of
22.5 seconds;
epsConfigurationMismatch(3) - provisioning mismatch - for example the local side is
set in revertive mode, the remote side is set in non revertive mode.ro PrvtEpsDefectFopType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.19 |
prvtEpsServiceOperationalStatusThe purpose of this status is to identify to the User whether
this service is ready for running. The operational status can
be up or down. When creating the service the operational
status will be down. Receiving CCMs from both transport
entities and establishment of APS on the protection transport
entity will bring the operational status to up.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.20 |
prvtEpsServicePrimaryStatusPrimary path state (psOk(0) or psFailed(1)).ro PrvtEpsPathStatusType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.21 |
prvtEpsServiceSecondaryStatusSecondary path state (psOk(0) or psFailed(1)).ro PrvtEpsPathStatusType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.22 |
prvtEpsServiceRemoteStateProtection state of the remote side.
The values can be get:
rsNoRequest (0),
rsDoNotRevert (1),
rsReverseRequest (2),
rsExercise (4),
rsWaitToRestore (5),
rsClear (6),
rsManualSwitch (7),
rsSignalDegrade (9),
rsSignalFail (11),
rsForcedSwitch (13),
rsSignalFailForProtection (14),
rsLockoutOfProtection (15).ro PrvtEpsRequestStateType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.23 |
prvtEpsServiceRemoteApsChannelActive APS communication reported by the remote.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.24 |
prvtEpsServiceRemoteProtectionType of protection (1+1 or 1:1) reported by the remote.ro PrvtEpsProtectionType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.25 |
prvtEpsServiceRemoteDirectionType of protection (unidirectional or bidirectional) reported by the remote.ro PrvtEpsDirectionType .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.26 |
prvtEpsServiceRemoteRevertiveProtection type (revertive or non-revertive) reported by the remote.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.27 |
prvtEpsServiceAdminFreezeUsed to freeze the state of the protection service.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.28 |
prvtEpsServiceAdminStatusAdministrative status of the protection.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.29 |
prvtEpsServiceRowStatusThe status of the row.
The writable columns in a row can not be changed if the row
is active. All columns must have a valid value before a row
can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.30 |
prvtEpsServiceProtectionCounterCounts how many times the service has gone to Protection.ro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.2.10.132.1.1.1.1.31 |