PM-MIB
AI MIB Summary
The PM-MIB module enables SNMP-based monitoring of power distribution unit (PDU) metrics, including outlet-level power consumption, current, voltage, and temperature sensors, specifically for Avocent PM-PDU hardware.
This module defines the Avocent MIB extensions to PM-PDU products.
Main OID:
pm.1.3.6.1.4.1.10418.17
293
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
293 total| Object Name |
|---|
pmThis module defines the Avocent MIB extensions to PM-PDU products. MODULE-IDENTITY .1.3.6.1.4.1.10418.17 |
pmProducts OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1 |
pm1024 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.1 |
pm2003 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.2 |
pm2006 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.3 |
pm2024 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.4 |
pm3003 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.5 |
pm3006 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.6 |
pm3024 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.7 |
pm1010 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.8 |
pm2010 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.9 |
pm3010 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.10 |
pm1020 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.11 |
pm2020 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.12 |
pm3020 OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.1.13 |
pmManagement OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.2 |
pmAppliance OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.2.1 |
pmHostNameThe appliance namero DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.1.1 |
pmProductModelThe appliance product modelro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.1.2 |
pmPartNumberThe part number of this appliance as shown on the label attached or imprinted on the appliance.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.1.3 |
pmSerialNumberThe serial number of this appliance as shown on the label attached or imprinted on the appliance.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.1.4 |
pmEIDNumberThe electronic ID number (EID) of this appliance as shown on the label attached or imprinted on the appliance.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.1.5 |
pmBootcodeVersionThe version of the bootcode of this appliance.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.1.6 |
pmFirmwareVersionThe version of the firmware of this appliance.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.1.7 |
pmRebootA set value of reboot(2) will reboot the appliance. noAction(1) = always returned in a GET. Does nothing if SET. reboot(2) = when SET the appliance immediately reboots.rw Enumeration .1.3.6.1.4.1.10418.17.2.1.9 |
pmSessions OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.2.2 |
pmActiveSessionsNumberOfSessionNumber of active sessions.ro Integer32 .1.3.6.1.4.1.10418.17.2.2.1 |
pmActiveSessionsTableThis table contains the list of active sessions. SEQUENCE OF PmActiveSessionsTableEntry .1.3.6.1.4.1.10418.17.2.2.2 |
pmActiveSessionsTableEntryeach entry has the information about the active session PmActiveSessionsTableEntry .1.3.6.1.4.1.10418.17.2.2.2.1 |
pmActiveSessionsTableIndexA unique index representing an entry in this table.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.10418.17.2.2.2.1.1 |
pmActiveSessionsTableUserThe name of the user that opens this session.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.2.2.1.2 |
pmActiveSessionsTableGroupThe name of the group that the user belongs to.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.2.2.1.3 |
pmActiveSessionsTableTypeThe session type.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.2.2.1.4 |
pmActiveSessionsTableConnectionConnection type.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.2.2.1.5 |
pmActiveSessionsTableSessionTimeTime of the sessionro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.2.2.1.6 |
pmActiveSessionsTableFromThe source IP address of the session.ro DisplayString ( SIZE .1.3.6.1.4.1.10418.17.2.2.2.1.7 |
pmActiveSessionsTableKillA set value of killSession(2) will kill the session. noAction(1) = always returned in a GET. Does nothing if SET. killSession(2)= when SET the appliance immediately kills the session.rw Enumeration .1.3.6.1.4.1.10418.17.2.2.2.1.8 |
pmPowerMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.2.5 |
pmPowerMgmtNumSerialPortsThe number of Serial Ports that has PDU connected on the appliance.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.1 |
pmPowerMgmtSerialTableInformation about each serial port thas has PDU connect. SEQUENCE OF PmPowerMgmtSerialTableEntry .1.3.6.1.4.1.10418.17.2.5.2 |
pmPowerMgmtSerialTableEntryInformation about each serial port thas has PDU connect. PmPowerMgmtSerialTableEntry .1.3.6.1.4.1.10418.17.2.5.2.1 |
pmPowerMgmtSerialTableIndexThe index of the register.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.2.1.1 |
pmPowerMgmtSerialTablePortNumberThe number of the serial port when the PDU is connected.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.2.1.2 |
pmPowerMgmtSerialTableDeviceNameThe device name of this serial port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.2.1.3 |
pmPowerMgmtSerialTableNumberPDUsTotal number of units connected in this serial port.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.2.1.4 |
pmPowerMgmtSerialTableBuzzerset/get buzzer(s) on or off for the chain. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.2.1.10 |
pmPowerMgmtSerialTableSyslogset/get syslog on or off for the chain. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.2.1.11 |
pmPowerMgmtSerialTableOverCurrentset/get over current proctection on or off for the chain. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.2.1.12 |
pmPowerMgmtSerialTableCycleIntervalset/get cycle interval for the chain in whole seconds. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.2.1.13 |
pmPowerMgmtSerialTablePollRateset/get the poll rate for the chain in whole seconds. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.2.1.14 |
pmPowerMgmtSerialTablePassWordset the global password for admin userrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.2.1.15 |
pmPowerMgmtSerialTableSavenoAction(1) = always returned in a GET. Does nothing if SET. save(2) = when SET the save command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.2.1.20 |
pmPowerMgmtSerialTableRestorenoAction(1) = always returned in a GET. Does nothing if SET. restore(2) = when SET the restore command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.2.1.21 |
pmPowerMgmtPDUTableThis table contains the list of detected PDUs. SEQUENCE OF PmPowerMgmtPDUTableEntry .1.3.6.1.4.1.10418.17.2.5.3 |
pmPowerMgmtPDUTableEntryeach entry has the information about the PDU. PmPowerMgmtPDUTableEntry .1.3.6.1.4.1.10418.17.2.5.3.1 |
pmPowerMgmtPDUTablePortNumberNumber of serial port when the PDU is connected.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.3.1.1 |
pmPowerMgmtPDUTablePduIndexA PDU position in the chain.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.3.1.2 |
pmPowerMgmtPDUTablePduIdPDU identification.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.3.1.3 |
pmPowerMgmtPDUTablePortNameName of serial port when the PDU is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.3.1.4 |
pmPowerMgmtPDUTableModelModel of the PDU. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.3.1.5 |
pmPowerMgmtPDUTableVendorVendor of the PDU. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.3.1.6 |
pmPowerMgmtPDUTableFirmwareVersionVersion of the PDU firmware. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.3.1.7 |
pmPowerMgmtPDUTableNumberOfOutletsNumber of outlets of the PDU.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.8 |
pmPowerMgmtPDUTableCurrentNOSNumber of current sensors in the PDU.roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.9 |
pmPowerMgmtPDUTableCurrent1ValueCurrent of the sensor 1 in this PDU unit in AMP. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.). This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentValue, pmPowerMgmtPhasesTableCurrentValue, or pmPowerMgmtOutletsTableCurrentValueroobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.10 |
pmPowerMgmtPDUTableCurrent1MaxMaximum current of the sensor 1 in this PDU unit in AMP. When the PDU does not have support for maximum value, the value will be 0. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) Clear this value, set it with Zero value. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentMax, pmPowerMgmtPhasesTableCurrentMax, or pmPowerMgmtOutletsTableCurrentMaxrwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.11 |
pmPowerMgmtPDUTableCurrent2ValueCurrent of the sensor 2 in this PDU unit in AMP. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.). This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentValue, pmPowerMgmtPhasesTableCurrentValue, or pmPowerMgmtOutletsTableCurrentValueroobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.12 |
pmPowerMgmtPDUTableCurrent2MaxMaximum current of the sensor 2 in this PDU unit in AMP. When the PDU does not have support for maximum value, the value will be 0. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) Clear this value, set it with Zero value. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentMax, pmPowerMgmtPhasesTableCurrentMax, or pmPowerMgmtOutletsTableCurrentMaxrwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.13 |
pmPowerMgmtPDUTableCurrent3ValueCurrent of the sensor 3 in this PDU unit in AMP. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentValue, pmPowerMgmtPhasesTableCurrentValue, or pmPowerMgmtOutletsTableCurrentValueroobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.14 |
pmPowerMgmtPDUTableCurrent3MaxMaximum current of the sensor 3 in this PDU unit in AMP. When the PDU does not have support for maximum value, the value will be 0. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) Clear this value, set it with Zero value. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentMax, pmPowerMgmtPhasesTableCurrentMax, or pmPowerMgmtOutletsTableCurrentMaxrwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.15 |
pmPowerMgmtPDUTableTemperatureNOSNumber of temperature sensors in the PDU.roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.16 |
pmPowerMgmtPDUTableTemperature1ValueTemperature of this PM unit in Celsius degrees. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius).roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.17 |
pmPowerMgmtPDUTableTemperature1MaxMaximum temperature detected in this PM unit in Celsius degrees. The value will be Zero when the PDU does not have support for maximum value. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius). Set with Zero value to clear the max. temperature.rwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.18 |
pmPowerMgmtPDUTableTemperature2ValueTemperature of this PM unit in Celsius degrees. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius).roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.19 |
pmPowerMgmtPDUTableTemperature2MaxMaximum temperature detected in this PM unit in Celsius degrees. The value will be Zero when the PDU does not have support for maximum value. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius). Set with Zero value to clear the max. temperature.rwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.20 |
pmPowerMgmtPDUTableTemperature3ValueTemperature of this PM unit in Celsius degrees. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius).roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.21 |
pmPowerMgmtPDUTableTemperature3MaxMaximum temperature detected in this PM unit in Celsius degrees. The value will be Zero when the PDU does not have support for maximum value. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius). Set with Zero value to clear the max. temperature.rwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.22 |
pmPowerMgmtPDUTableHumidityNOSNumber of humidity sensors in the PDU.roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.23 |
pmPowerMgmtPDUTableHumidity1ValueHumidity of this PM unit . If the humidity measurement is not installed this value will be 0.roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.24 |
pmPowerMgmtPDUTableHumidity1MaxMaximum humidity detected in this PM unit. If the humidity measurement is not installed or the PDU does not have support for maximum value this value will be 0. Set with Zero value to clear the max. temperature.rwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.25 |
pmPowerMgmtPDUTableHumidity2ValueHumidity of this PM unit . If the humidity measurement is not installed this value will be 0.roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.26 |
pmPowerMgmtPDUTableHumidity2MaxMaximum humidity detected in this PM unit. If the humidity measurement is not installed or the PDU does not have support for maximum value this value will be 0. Set with Zero value to clear the max. temperature.rwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.27 |
pmPowerMgmtPDUTableHumidity3ValueHumidity of this PM unit . If the humidity measurement is not installed this value will be 0.roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.28 |
pmPowerMgmtPDUTableHumidity3MaxMaximum humidity detected in this PM unit. If the humidity measurement is not installed or the PDU does not have support for maximum value this value will be 0. Set with Zero value to clear the max. temperature.rwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.29 |
pmPowerMgmtPDUTableVoltageNOSNumber of voltage sensors in the PDU.roobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.30 |
pmPowerMgmtPDUTableVoltage1ValueVoltage of this sensor in this PDU unit. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageValue, pmPowerMgmtPhasesTableVoltageValue, or pmPowerMgmtOutletsTableVoltageValueroobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.31 |
pmPowerMgmtPDUTableVoltage1MaxMaximum voltage of this sensor in this PDU unit. Set with Zero value to clear the maximum voltage. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageMax, pmPowerMgmtPhasesTableVoltageMax, or pmPowerMgmtOutletsTableVoltageMaxrwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.32 |
pmPowerMgmtPDUTableVoltage2ValueVoltage of this sensor in this PDU unit. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageValue, pmPowerMgmtPhasesTableVoltageValue, or pmPowerMgmtOutletsTableVoltageValueroobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.33 |
pmPowerMgmtPDUTableVoltage2MaxMaximum voltage of this sensor in this PDU unit. Set with Zero value to clear the maximum voltage. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageMax, pmPowerMgmtPhasesTableVoltageMax, or pmPowerMgmtOutletsTableVoltageMaxrwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.34 |
pmPowerMgmtPDUTableVoltage3ValueVoltage of this sensor in this PDU unit. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageValue, pmPowerMgmtPhasesTableVoltageValue, or pmPowerMgmtOutletsTableVoltageValueroobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.35 |
pmPowerMgmtPDUTableVoltage3MaxMaximum voltage of this sensor in this PDU unit. Set with Zero value to clear the maximum voltage. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageMax, pmPowerMgmtPhasesTableVoltageMax, or pmPowerMgmtOutletsTableVoltageMaxrwobsolete Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.36 |
pmPowerMgmtPDUTableNumberOfPhasesNumber of phases of the PDU.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.37 |
pmPowerMgmtPDUTableNumberOfBanksNumber of banks in the PDU.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.38 |
pmPowerMgmtPDUTableNumberOfSensorsNumber of sensors in the PDU.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.40 |
pmPowerMgmtPDUTableFactoryDefaultA set value of 2 will set the PDU to factory default settings. noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the factory default command is sent to the PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.41 |
pmPowerMgmtPDUTableColdStartDelayPDUs cold start delay in whole seconds (0-60). Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.42 |
pmPowerMgmtPDUTableRebootA set value of power*(2) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. reboot(2) = when SET the reboot command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.43 |
pmPowerMgmtPDUTableMaxCurrentMaximum value of current allowed in the PDU (A x 10).ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.44 |
pmPowerMgmtPDUTableAlarmShow the PDU alarm status. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.45 |
pmPowerMgmtPDUTableCurrentValueActual value of current in the PDU (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.50 |
pmPowerMgmtPDUTableCurrentMaxMaximum value of current in the PDU (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.51 |
pmPowerMgmtPDUTableCurrentMinMinimum value of current in the PDU (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.52 |
pmPowerMgmtPDUTableCurrentAvgAverage value of current in the PDU (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.53 |
pmPowerMgmtPDUTableCurrentResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.54 |
pmPowerMgmtPDUTablePowerValueActual value of power in the PDU (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.60 |
pmPowerMgmtPDUTablePowerMaxMaximum value of power in the PDU (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.61 |
pmPowerMgmtPDUTablePowerMinMinimum value of power in the PDU (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.62 |
pmPowerMgmtPDUTablePowerAvgAverage value of power in the PDU (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.63 |
pmPowerMgmtPDUTablePowerResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.64 |
pmPowerMgmtPDUTablePowerTypeType of power values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.65 |
pmPowerMgmtPDUTableVoltageValueActual value of voltage in the PDU (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.70 |
pmPowerMgmtPDUTableVoltageMaxMaximum value of voltage in the PDU (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.71 |
pmPowerMgmtPDUTableVoltageMinMinimum value of voltage in the PDU (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.72 |
pmPowerMgmtPDUTableVoltageAvgAverage value of voltage in the PDU (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.73 |
pmPowerMgmtPDUTableVoltageResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.74 |
pmPowerMgmtPDUTableVoltageTypeType of voltage values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.75 |
pmPowerMgmtPDUTablePowerFactorValueActual value of power factor in the PDU (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.80 |
pmPowerMgmtPDUTablePowerFactorMaxMaximum value of power factor in the PDU (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.81 |
pmPowerMgmtPDUTablePowerFactorMinMinimum value of power factor in the PDU (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.82 |
pmPowerMgmtPDUTablePowerFactorAvgAverage value of power factor in the PDU (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.83 |
pmPowerMgmtPDUTablePowerFactorResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.84 |
pmPowerMgmtPDUTablePowerFactorTypeType of power values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.85 |
pmPowerMgmtPDUTablePowerControlA set value of power*(2-4) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. powerOn(2) = when SET the power On command is sent to PDU. powerOff(3) = when SET the power Off command is sent to PDU. powerCycle(4)=when SET the power cycle command is sent to PDU. Returns 0 if not supported.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.90 |
pmPowerMgmtPDUTableResetOCPA set value of power*(2) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU. Returns 0 if not supported.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.91 |
pmPowerMgmtPDUTableCurrentHighCriticaloutlet high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.100 |
pmPowerMgmtPDUTableCurrentHighWarningoutlet high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.101 |
pmPowerMgmtPDUTableCurrentLowWarningoutlet low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.102 |
pmPowerMgmtPDUTableCurrentLowCriticaloutlet low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.103 |
pmPowerMgmtPDUTableEnergyValuepdu energy value (Wh). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.3.1.105 |
pmPowerMgmtPDUTableEnergyStartTimetime at which energy calculation commenced (ISO8601 format). Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.3.1.106 |
pmPowerMgmtPDUTableEnergyResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.3.1.107 |
pmPowerMgmtTotalNumberOfOutletsNumber of outlets managed by the appliance.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.4 |
pmPowerMgmtOutletsTableThis table contains the information about outlets. SEQUENCE OF PmPowerMgmtOutletsTableEntry .1.3.6.1.4.1.10418.17.2.5.5 |
pmPowerMgmtOutletsTableEntryeach entry has the information about the outlet. PmPowerMgmtOutletsTableEntry .1.3.6.1.4.1.10418.17.2.5.5.1 |
pmPowerMgmtOutletsTablePortNumberSerial Port number.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.5.1.1 |
pmPowerMgmtOutletsTablePduNumberIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.5.1.2 |
pmPowerMgmtOutletsTableNumberNumber of the outlet in the PDU.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.5.1.3 |
pmPowerMgmtOutletsTableNameName of the outlet.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.5.1.4 |
pmPowerMgmtOutletsTableStatusStatus of the outlet. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.5 |
pmPowerMgmtOutletsTablePowerControlA set value of power*(2-6) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. powerOn(2) = when SET the power On command is sent to PDU. powerOff(3) = when SET the power Off command is sent to PDU. powerCycle(4)=when SET the power cycle command is sent to PDU. powerLock(5)= when SET the power lock command is sent to PDU. powerUnlock(6)=when SET the power unlock command is sent to PDU. The powerLock and powerUnlock are valid only for Cyclades-PM PDUsrw Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.6 |
pmPowerMgmtOutletsTablePortNameSerial Port Name where the PDU is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.5.1.7 |
pmPowerMgmtOutletsTablePduIdPDU identification.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.5.1.8 |
pmPowerMgmtOutletsTablePostOnDelaypost on delay for the outlet (seconds x 10) Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.9 |
pmPowerMgmtOutletsTablePostOffDelaypost off delay for the outlet (seconds x 10) Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.10 |
pmPowerMgmtOutletsTableAlarmShow the outlet alarm status. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.45 |
pmPowerMgmtOutletsTableCurrentValueActual value of current in the outlet (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.50 |
pmPowerMgmtOutletsTableCurrentMaxMaximum value of current in the outlet (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.51 |
pmPowerMgmtOutletsTableCurrentMinMinimum value of current in the outlet (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.52 |
pmPowerMgmtOutletsTableCurrentAvgAverage value of current in the outlet (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.53 |
pmPowerMgmtOutletsTableCurrentResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.54 |
pmPowerMgmtOutletsTablePowerValueActual value of power in the outlet (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.60 |
pmPowerMgmtOutletsTablePowerMaxMaximum value of power in the outlet (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.61 |
pmPowerMgmtOutletsTablePowerMinMinimum value of power in the outlet (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.62 |
pmPowerMgmtOutletsTablePowerAvgAverage value of power in the outlet (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.63 |
pmPowerMgmtOutletsTablePowerResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.64 |
pmPowerMgmtOutletsTablePowerTypeType of power values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.65 |
pmPowerMgmtOutletsTableVoltageValueActual value of voltage in the outlet (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.70 |
pmPowerMgmtOutletsTableVoltageMaxMaximum value of voltage in the outlet (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.71 |
pmPowerMgmtOutletsTableVoltageMinMinimum value of voltage in the outlet (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.72 |
pmPowerMgmtOutletsTableVoltageAvgAverage value of voltage in the outlet (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.73 |
pmPowerMgmtOutletsTableVoltageResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.74 |
pmPowerMgmtOutletsTableVoltageTypeType of voltage values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.75 |
pmPowerMgmtOutletsTablePowerFactorValueActual value of power factor in the outlet (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.80 |
pmPowerMgmtOutletsTablePowerFactorMaxMaximum value of power factor in the outlet (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.81 |
pmPowerMgmtOutletsTablePowerFactorMinMinimum value of power factor in the outlet (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.82 |
pmPowerMgmtOutletsTablePowerFactorAvgAverage value of power factor in the outlet (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.83 |
pmPowerMgmtOutletsTablePowerFactorResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.84 |
pmPowerMgmtOutletsTablePowerFactorTypeType of power factor values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.85 |
pmPowerMgmtOutletsTableCurrentHighCriticaloutlet high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.100 |
pmPowerMgmtOutletsTableCurrentHighWarningoutlet high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.101 |
pmPowerMgmtOutletsTableCurrentLowWarningoutlet low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.102 |
pmPowerMgmtOutletsTableCurrentLowCriticaloutlet low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.103 |
pmPowerMgmtOutletsTableEnergyValueoutlet energy value (Wh). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.5.1.105 |
pmPowerMgmtOutletsTableEnergyStartTimetime at which energy calculation commenced (ISO8601 format). Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.5.1.106 |
pmPowerMgmtOutletsTableEnergyResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.5.1.107 |
pmPowerMgmtNumberOfOutletGroupNumber of configured group of outlets.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.6 |
pmPowerMgmtGroupTableThis table contains the information about group of outlets. SEQUENCE OF PmPowerMgmtGroupTableEntry .1.3.6.1.4.1.10418.17.2.5.7 |
pmPowerMgmtGroupTableEntryeach entry has the information about group of outlets. PmPowerMgmtGroupTableEntry .1.3.6.1.4.1.10418.17.2.5.7.1 |
pmPowerMgmtGroupTableIndexIndex of the group.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.7.1.1 |
pmPowerMgmtGroupTableNameName of the group of outlets.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.7.1.2 |
pmPowerMgmtGroupTableStatusStatus of the group of outlet.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.7.1.3 |
pmPowerMgmtGroupTablePowerControlA set value of power*(2-4) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. powerOn(2) = when SET the power On command is sent to PDU. powerOff(3) = when SET the power Off command is sent to PDU. powerCycle(4)=when SET the power cycle command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.7.1.4 |
pmPowerMgmtTotalNumberOfPhasesNumber of phases managed by the appliance.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.8 |
pmPowerMgmtPhasesTableThis table contains the information about phases. SEQUENCE OF PmPowerMgmtPhasesTableEntry .1.3.6.1.4.1.10418.17.2.5.9 |
pmPowerMgmtPhasesTableEntryeach entry has the information about the phases. PmPowerMgmtPhasesTableEntry .1.3.6.1.4.1.10418.17.2.5.9.1 |
pmPowerMgmtPhasesTablePortNumberSerial Port number.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.9.1.1 |
pmPowerMgmtPhasesTablePduNumberIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.9.1.2 |
pmPowerMgmtPhasesTableNumberNumber of the phase in the PDU.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.9.1.3 |
pmPowerMgmtPhasesTableNameName of the phase. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.9.1.4 |
pmPowerMgmtPhasesTablePortNameSerial Port Name where the PDU is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.9.1.5 |
pmPowerMgmtPhasesTablePduIdPDU identification.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.9.1.6 |
pmPowerMgmtPhasesTableAlarmShow the phase alarm status. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.45 |
pmPowerMgmtPhasesTableCurrentValueActual value of current in the phase (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.50 |
pmPowerMgmtPhasesTableCurrentMaxMaximum value of current in the phase (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.51 |
pmPowerMgmtPhasesTableCurrentMinMinimum value of current in the phase (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.52 |
pmPowerMgmtPhasesTableCurrentAvgAverage value of current in the phase (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.53 |
pmPowerMgmtPhasesTableCurrentResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.54 |
pmPowerMgmtPhasesTablePowerValueActual value of power in the phase (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.60 |
pmPowerMgmtPhasesTablePowerMaxMaximum value of power in the phase (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.61 |
pmPowerMgmtPhasesTablePowerMinMinimum value of power in the phase (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.62 |
pmPowerMgmtPhasesTablePowerAvgAverage value of power in the phase (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.63 |
pmPowerMgmtPhasesTablePowerResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.64 |
pmPowerMgmtPhasesTablePowerTypeType of power values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.65 |
pmPowerMgmtPhasesTableVoltageValueActual value of voltage in the phase (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.70 |
pmPowerMgmtPhasesTableVoltageMaxMaximum value of voltage in the phase (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.71 |
pmPowerMgmtPhasesTableVoltageMinMinimum value of voltage in the phase (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.72 |
pmPowerMgmtPhasesTableVoltageAvgAverage value of voltage in the phase (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.73 |
pmPowerMgmtPhasesTableVoltageResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.74 |
pmPowerMgmtPhasesTableVoltageTypeType of voltage values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.75 |
pmPowerMgmtPhasesTablePowerFactorValueActual value of power factor in the phase (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.80 |
pmPowerMgmtPhasesTablePowerFactorMaxMaximum value of power factor in the phase (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.81 |
pmPowerMgmtPhasesTablePowerFactorMinMinimum value of power factor in the phase (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.82 |
pmPowerMgmtPhasesTablePowerFactorAvgAverage value of power factor in the phase (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.83 |
pmPowerMgmtPhasesTablePowerFactorResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.84 |
pmPowerMgmtPhasesTablePowerFactorTypeType of power factor values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.9.1.85 |
pmPowerMgmtPhasesTableCurrentHighCriticalphase high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.100 |
pmPowerMgmtPhasesTableCurrentHighWarningphase high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.101 |
pmPowerMgmtPhasesTableCurrentLowWarningphase low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.102 |
pmPowerMgmtPhasesTableCurrentLowCriticalphase low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.9.1.103 |
pmPowerMgmtTotalNumberOfBanksNumber of banks managed by the appliance.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.10 |
pmPowerMgmtBanksTableThis table contains the information about banks. SEQUENCE OF PmPowerMgmtBanksTableEntry .1.3.6.1.4.1.10418.17.2.5.11 |
pmPowerMgmtBanksTableEntryeach entry has the information about the banks. PmPowerMgmtBanksTableEntry .1.3.6.1.4.1.10418.17.2.5.11.1 |
pmPowerMgmtBanksTablePortNumberSerial Port number.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.11.1.1 |
pmPowerMgmtBanksTablePduNumberIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.11.1.2 |
pmPowerMgmtBanksTableNumberNumber of the bank in the PDU.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.11.1.3 |
pmPowerMgmtBanksTableNameName of the bank.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.11.1.4 |
pmPowerMgmtBanksTablePortNameSerial Port Name where the PDU is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.11.1.5 |
pmPowerMgmtBanksTablePduIdPDU identification.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.11.1.6 |
pmPowerMgmtBanksTableAlarmShow the bank alarm status. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.45 |
pmPowerMgmtBanksTableCurrentValueActual value of current in the bank (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.50 |
pmPowerMgmtBanksTableCurrentMaxMaximum value of current in the bank (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.51 |
pmPowerMgmtBanksTableCurrentMinMinimum value of current in the bank (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.52 |
pmPowerMgmtBanksTableCurrentAvgAverage value of current in the bank (A x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.53 |
pmPowerMgmtBanksTableCurrentResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.54 |
pmPowerMgmtBanksTablePowerValueActual value of power in the bank (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.60 |
pmPowerMgmtBanksTablePowerMaxMaximum value of power in the bank (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.61 |
pmPowerMgmtBanksTablePowerMinMinimum value of power in the bank (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.62 |
pmPowerMgmtBanksTablePowerAvgAverage value of power in the bank (W x 10). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.63 |
pmPowerMgmtBanksTablePowerResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.64 |
pmPowerMgmtBanksTablePowerTypeType of power values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.65 |
pmPowerMgmtBanksTableVoltageValueActual value of voltage in the bank (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.70 |
pmPowerMgmtBanksTableVoltageMaxMaximum value of voltage in the bank (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.71 |
pmPowerMgmtBanksTableVoltageMinMinimum value of voltage in the bank (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.72 |
pmPowerMgmtBanksTableVoltageAvgAverage value of voltage in the bank (V). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.73 |
pmPowerMgmtBanksTableVoltageResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.74 |
pmPowerMgmtBanksTableVoltageTypeType of voltage values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.75 |
pmPowerMgmtBanksTablePowerFactorValueActual value of power factor in the bank (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.80 |
pmPowerMgmtBanksTablePowerFactorMaxMaximum value of power factor in the bank (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.81 |
pmPowerMgmtBanksTablePowerFactorMinMinimum value of power factor in the bank (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.82 |
pmPowerMgmtBanksTablePowerFactorAvgAverage value of power factor in the bank (Pf x 100). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.83 |
pmPowerMgmtBanksTablePowerFactorResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.84 |
pmPowerMgmtBanksTablePowerFactorTypeType of power factor values. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.85 |
pmPowerMgmtBanksTableCurrentHighCriticalbank high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.100 |
pmPowerMgmtBanksTableCurrentHighWarningbank high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.101 |
pmPowerMgmtBanksTableCurrentLowWarningbank low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.102 |
pmPowerMgmtBanksTableCurrentLowCriticalbank low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.103 |
pmPowerMgmtBanksTableEnergyValuebank energy value (Wh). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.11.1.105 |
pmPowerMgmtBanksTableEnergyStartTimetime at which energy calculation commenced (ISO8601 format). Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.11.1.106 |
pmPowerMgmtBanksTableEnergyResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.11.1.107 |
pmPowerMgmtTotalNumberOfSensorsNumber of Sensors managed by the appliance.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.12 |
pmPowerMgmtSensorsTableThis table contains the information about sensors. SEQUENCE OF PmPowerMgmtSensorsTableEntry .1.3.6.1.4.1.10418.17.2.5.13 |
pmPowerMgmtSensorsTableEntryeach entry has the information about the sensors. PmPowerMgmtSensorsTableEntry .1.3.6.1.4.1.10418.17.2.5.13.1 |
pmPowerMgmtSensorsTablePortNumberSerial Port number.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.13.1.1 |
pmPowerMgmtSensorsTablePduNumberIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.13.1.2 |
pmPowerMgmtSensorsTableNumberNumber of the sensor in the PDU.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.10418.17.2.5.13.1.3 |
pmPowerMgmtSensorsTableNameName of the sensor.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.13.1.4 |
pmPowerMgmtSensorsTablePortNameSerial Port Name where the PDU is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.13.1.5 |
pmPowerMgmtSensorsTablePduIdPDU identification.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.13.1.6 |
pmPowerMgmtSensorsTableTypeThe type of environmental monitor. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.13.1.7 |
pmPowerMgmtSensorsTableStatusStatus of digital sensors: Dry-Contact, Water level, Smoke sensor, Motion sensor. Returns 0 if not supported.ro Enumeration .1.3.6.1.4.1.10418.17.2.5.13.1.8 |
pmPowerMgmtSensorsTableValueActual value of the sensor. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.13.1.20 |
pmPowerMgmtSensorsTableValueMaxMaximum value of the sensor. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.13.1.21 |
pmPowerMgmtSensorsTableValueMinMinimum value of the sensor. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.13.1.22 |
pmPowerMgmtSensorsTableValueAvgAverage value of the sensor. Returns N/A if not applicable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.10418.17.2.5.13.1.23 |
pmPowerMgmtSensorsTableValueIntActual value of the sensor. Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.25 |
pmPowerMgmtSensorsTableValueMaxIntMaximum value of the sensor. Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.26 |
pmPowerMgmtSensorsTableValueMinIntMinimum value of the sensor. Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.27 |
pmPowerMgmtSensorsTableValueAvgIntAverage value of the sensor. Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.28 |
pmPowerMgmtSensorsTableValueResetnoAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to sensor.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.13.1.30 |
pmPowerMgmtSensorsTableHighCriticalsensor high critical (alarm) threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.40 |
pmPowerMgmtSensorsTableHighWarningsensor high warning threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is higher than HighCritical or lower than LowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.41 |
pmPowerMgmtSensorsTableLowWarningsensor low warning threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is higher than HighWarning or lower than LowCritical. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.42 |
pmPowerMgmtSensorsTableLowCriticalsensor low critical threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is higher than LowWarning. Returns 0 if not supported.rw Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.43 |
pmPowerMgmtSensorsTableUnitsensor unit. Returns 0 if not supported.rw Enumeration .1.3.6.1.4.1.10418.17.2.5.13.1.45 |
pmPowerMgmtSensorsTableHighCriticalCsensor high critical (alarm) threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableHighCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.50 |
pmPowerMgmtSensorsTableHighWarningCsensor high warning threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableHighWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.51 |
pmPowerMgmtSensorsTableLowWarningCsensor low warning threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableLowWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.52 |
pmPowerMgmtSensorsTableLowCriticalCsensor low critical threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableLowCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.53 |
pmPowerMgmtSensorsTableHighCriticalFsensor high critical (alarm) threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableHighCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.60 |
pmPowerMgmtSensorsTableHighWarningFsensor high warning threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableHighWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.61 |
pmPowerMgmtSensorsTableLowWarningFsensor low warning threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableLowWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.62 |
pmPowerMgmtSensorsTableLowCriticalFsensor low critical threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableLowCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.ro Integer32 .1.3.6.1.4.1.10418.17.2.5.13.1.63 |
pmTrapObject OBJECT IDENTIFIER .1.3.6.1.4.1.10418.17.2.6 |