PDN-ETHER-MIB
This MIB contains objects that are used to configure ethernet interfaces.
Main OID:
pdn-ether.pdn-common.18
21
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
21 total| Object Name |
|---|
pdn-etherThis MIB contains objects that are used to configure
ethernet interfaces. MODULE-IDENTITY .pdn-common.18 |
IMPORTSThis MIB contains objects that are used to configure
ethernet interfaces. Unknown .pdn-common.18 |
pdnPortConfigMIBObjects OBJECT IDENTIFIER .pdn-common.18.1 |
pdnPortConfigEthernet OBJECT IDENTIFIER .pdn-common.18.1.1 |
pdnPortConfigEthernetTableA Table that contains information about
the Ethernet port configuration SEQUENCE OF PdnPortConfigEthernetEntry .pdn-common.18.1.1.1 |
pdnPortConfigEthernetEntryAn entry that contains configuration
information about an ethernet Port PdnPortConfigEthernetEntry .pdn-common.18.1.1.1.1 |
pdnPortConfigEthernetDuplexModeThis object is used to enable or Disable
Duplex Mode on an ethernet Port. This object
can not be enabled if the auto-negotiate
mode is enabledrw SwitchState (PDN-TC) .pdn-common.18.1.1.1.1.1 |
pdnPortConfigEthernetManageTypeThis object is used to Enable or
Disable Inband or Outband Management.rw ManagementType (PDN-TC) .pdn-common.18.1.1.1.1.2 |
pdnPortConfigEthernetResetStateThis object is used to reset the ethernet port.rw ResetStates (PDN-TC) .pdn-common.18.1.1.1.1.3 |
pdnPortConfigEthernetAutoNegotiateThis object is used to enable or disable
the auto-negotiate mode. Enabling this
mode will disable selection of the speed
and/or full duplex mode.rw SwitchState (PDN-TC) .pdn-common.18.1.1.1.1.4 |
pdnPortConfigEthernetSpeedThis object corresponds to the speed of
the ethernet port. This object can not be
set if the auto-negotiate mode is enabled.rw Enumeration .pdn-common.18.1.1.1.1.5 |
pdnPortConfigGroups OBJECT IDENTIFIER .pdn-common.18.1.2 |
pdnPortConfigMauExtMIBObject OBJECT IDENTIFIER .pdn-common.18.1.3 |
pdnPortConfigMauExtTableA Table that contains configuration information about
the Ethernet port configuration and it extends standard
MAU table from RFC2668. SEQUENCE OF PdnPortConfigMauExtEntry .pdn-common.18.1.3.1 |
pdnPortConfigMauExtEntryAn entry that contains configuration
information about an ethernet Port PdnPortConfigMauExtEntry .pdn-common.18.1.3.1.1 |
pdnPortConfigXoverThis object is used to configure
if crossover or straightthrough cable is
used on ethernet interface if the interface
is not set for autonegotiontion.rw Enumeration .pdn-common.18.1.3.1.1.1 |
pdnPortConfigIfJackMIBObject OBJECT IDENTIFIER .pdn-common.18.1.4 |
pdnIfJackTableThis table conceptually extends the ifJackTable
but not as an augmentation. See the note above. SEQUENCE OF PdnIfJackEntry .pdn-common.18.1.4.1 |
pdnIfJackEntryAn entry that contains configuration information
about a jack. PdnIfJackEntry .pdn-common.18.1.4.1.1 |
pdnActiveJackThis object allows the jack type to be configured or a
priority to be set. This applies to Ethernet interfaces
that may support more than one type of jack on an inter-
face and only one jack is valid at a time. Consider two
cases:
1. A product supports two types of jacks, a RJ45 copper-
wire interface and a SFP fiber interface. The product is
required to have the user set the active jack or allow it
to be auto detected. The values for this object that
allow the requirement to be satisfied and their interp-
retation are as follows:
a. fiber(1) - The fiber jack is active and the others,
e.g. rj45, are ignored.
b. rj45(2) - The rj45 jack is actie and the others,
eg.fiber, are ignored.
c. auto(3) - Either jack can be used and it is up
to the implementation to determine which
jack has presedence when both jacks are
active. This determination must be clearly
documented in the SNMP Operational Speci-
fication.
No default is specified for this MIB object so the default
value for this object must be clearly documented in the
SNMP Operational Specification.
2. A product supports two types of jacks, a RJ45 copper-
wire interface and s SFP fiber interface. The product is
required to have the user select which jack has priority
when both jacks are active. The values for this object
that allow the requirement to be satisfied and their
interpretation are as follos:
a. fiber(1) - The fiber jack has priority.
b. rj45(2) - The rj45 jack has priority.
c. auto(3) - Not used.rw Enumeration .pdn-common.18.1.4.1.1.1 |
pdnPortConfigMIBTraps OBJECT IDENTIFIER .pdn-common.18.2 |