PDN-DOT1QEXT-MIB
AI MIB Summary
The PDN-DOT1QEXT-MIB enables Paradyne enterprise equipment to monitor and configure IEEE 802.1Q VLAN tagging parameters beyond the standard RFC 2674 scope, specifically exposing proprietary dot1qExt objects for extended VLAN management.
The Paradyne enterprise DOT1q extension MIB. This MIB provides additional DOT1q configuration objects not provided by rfc2674.
Main OID:
pdnDot1qExt.pdn-dot1q.1
20
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
20 total| Object Name |
|---|
pdnDot1qExtThe Paradyne enterprise DOT1q extension MIB.
This MIB provides additional DOT1q configuration
objects not provided by rfc2674. MODULE-IDENTITY .pdn-dot1q.1 |
pdnDot1qExtObjects OBJECT IDENTIFIER .pdn-dot1q.1.1 |
pdnDot1qVlanStaticExtTableThe Paradyne dot1qVlanStatic extension table.
This table is used for configuring extensions
to static vlans. SEQUENCE OF PdnDot1qVlanStaticExtEntry .pdn-dot1q.1.1.1 |
pdnDot1qVlanStaticExtEntryAn entry in the Paradyne dot1q extension to
Static Vlan Table PdnDot1qVlanStaticExtEntry .pdn-dot1q.1.1.1.1 |
pdnDot1qVlanStaticSecureModeStatusThis is objects configure secure mode status for the
selected VLAN. The secure VLAN mode implies that the users
on this VLAN cannot talk to users on a different VLAN. This
setting also validates the configuration of the next three
objects in this table. If the pdnDot1qVlanStaticSecureModeStatus
is disabled non of the other three objects configurations
apply.rw Enumeration .pdn-dot1q.1.1.1.1.1 |
pdnDot1qVlanStaticProxyArpStatusThis objects enables/disabled proxy arp on secure VLAN. If the
VLAN is secure, it can optionally have Proxy ARP enabled.
This object is not valid unless pdnDot1qVlanStaticSecureModeStatus
is set to ENABLED.This object will be disabled(1) by default.rw Enumeration .pdn-dot1q.1.1.1.1.2 |
pdnDot1qVlanStaticUplinkThis is used to configure the port number of the port on
which all frames belonging to secure VLAN are to be forwarded.
This object is not valid unless pdnDot1qVlanStaticSecureModeStatus
is set to ENABLED. If pdnDot1qVlanStaticSecureModeStatus is disabled
this object will read 0 port.rw Integer32 .pdn-dot1q.1.1.1.1.3 |
pdnDot1qVlanStaticDefaultNHRThis object is used to configure Default Next Hop Router
Ip Address that would be used only if the Next Hop Router
cannot be learned (i.e from snooping messages).
This object is not valid unless pdnDot1qVlanStaticSecureModeStatus
is set to ENABLED. If pdnDot1qVlanStaticSecureModeStatus is disabled
this object will read 0.0.0.0 address.rw IpAddress .pdn-dot1q.1.1.1.1.4 |
pdnDot1qVlanStaticOuterTagWhen VLAN stacking (Q in Q) is desired, this object contains the
value of the outer 802.1q VLAN outer tag.
A value of zero (0) indicates that VLAN stacking is not enabled.rw Integer32 .pdn-dot1q.1.1.1.1.5 |
pdnDot1qVlanStaticOuterDefaultPriorityWhen VLAN stacking (Q in Q) is desired, this object contains the
default value of the priority bits in the 802.1q VLAN outer tag
for unknown unicast, broadcast and multicast packets.
For known unicast traffic, the inner VLAN tag priority is copied to
the outer tag priority.
If pdnDot1qVlanStaticOuterTag (above) is zero (0) this object is ignored.rw Integer32 .pdn-dot1q.1.1.1.1.6 |
pdnDot1qVlanStaticOuterEthertypeWhen VLAN stacking (Q in Q) is desired, this object contains the
value of the ethertype in the 802.1q VLAN outer tag.
If pdnDot1qVlanStaticOuterTag (above) is zero (0) this object is ignored.rw Integer32 .pdn-dot1q.1.1.1.1.7 |
pdnDot1BasePortPIWGTableThis table allows mapping of Bridge Ports and Priorities.
In General, every bridge port has an associated physical port
port (identified by its ifIndex). This relationship is defined
in the Dot1dBasePortTable (RFC1493).
In addition, each bridge port is associated with one priority
(PIWG) from a range of valid priorities. This table defines
this relationship.
The range of priorities can vary from product to product. SEQUENCE OF PdnDot1BasePortPIWGEntry .pdn-dot1q.1.1.2 |
pdnDot1BasePortPIWGEntryThe priority (PIWG) defined on a Bridge port. PdnDot1BasePortPIWGEntry .pdn-dot1q.1.1.2.1 |
pdnDot1BasePortThis object specifies the bridge port associated
with this PIWG Unsigned32 .pdn-dot1q.1.1.2.1.1 |
pdnDot1BasePortPIWGIdThis is the integer identifier of the priority (PIWG)ro Unsigned32 .pdn-dot1q.1.1.2.1.2 |
pdnDot1BasePortPIWGCircuitThis is the object identifier of the priority (PIWG),
The value of this object must be a valid identifier
defined under the Paradyne Enterprise Definitions
(pdn_Header.mib).ro OBJECT IDENTIFIER .pdn-dot1q.1.1.2.1.3 |
pdnDot1TpFdbClearThis object is used to perform a clear on the
Bridge Forwarding Table (dot1dTpFdbTable).
A set operation to this object with the value of 'clear (2)'
will clear the entire Bridge Forwarding Table.
A get operation will always return the value of 'noCmd (1)'.rw TblCmd .pdn-dot1q.1.1.3 |
pdnDot1qExtConformance OBJECT IDENTIFIER .pdn-dot1q.1.2 |
pdnDot1qExtGroups OBJECT IDENTIFIER .pdn-dot1q.1.2.1 |
pdnDot1qExtCompliances OBJECT IDENTIFIER .pdn-dot1q.1.2.2 |