Home/Catalog/OPTICSIM-ETHNE-MIB

OPTICSIM-ETHNE-MIB

AI MIB Summary

The OPTICSIM-ETHNE-MIB module facilitates the monitoring and management of Ethernet network elements within Opticsim optical transport systems, specifically exposing physical layer metrics such as optical power levels, laser bias currents, and transceiver temperature status via SNMP.

Optics-IM Ethernet NE MIB
Main OID:
opticsimEthNEMib.1.3.6.1.4.1.637.54.1.25.2
148
Objects
Active
Status
8
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
IF-MIB
OPTICSIM-ETHREG-MIB
MAU-MIB
OpticsIMETS-MIB
TSDIM-SNMP-TC
RFC1155-SMI

Objects

148 total
Object Name
opticsimEthNEMibOptics-IM Ethernet NE MIB
MODULE-IDENTITY
.1.3.6.1.4.1.637.54.1.25.2
opticsimEthNEMibObject
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.25.2.1
opticsIMEthConfTableThis media-specific interface table is used to define the proprietary configuration parameters for the Ethernet interfaces.
SEQUENCE OF OpticsIMEthConfEntry
.1.3.6.1.4.1.637.54.1.25.2.1.1
opticsIMEthConfEntry
OpticsIMEthConfEntry
.1.3.6.1.4.1.637.54.1.25.2.1.1.1
opticsIMEthMauIndexThis attribute contains the number of the MAU port that is associated to an internal interface at MAU creation time. This object must be 0 if the interface has not a 'Mau' Underlie Layer.rw
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.1
opticsIMEthJackIndexThis attribute contains the number of the MAU connector that is associated to a MAU port at MAU and hence to an internal interface at MAU creation time. This object must be 0 if the interface has not a 'Mau' Underlie Layer.rw
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.2
opticsIMEthConfEncapsThe encapsulation method used by the local Ethernet entity.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.3
opticsIMEthAvailableBandwidthThis value indicates the total amount of available bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in ifSpeed (converted in Kbps). When this value cannot be measured, this value should contain the nominal bandwidth.ro
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.4
opticsIMEthConfVLANEtherTypeThis object points to an entry in the opticsIMEthVLANTypeTable that represents the EtherType value used to detect VLAN tagged frames received from this interface as well as to insert VLAN tag(s) to the frames to be transmitted (when applicable). The value 0 is reserved to represent the IEEE 802.1Q standard EtherType (i.e. 0x8100). The default value is 0 (IEEE 802.1Q standard EtherType). The value of this object is meaningless for MAC bridge (IEEE 802.1D) ports. The value of this object MUST be equal to 0 for Virtual bridge (IEEE 802.1Q) ports. The value of this object MUST be the same for all Provider bridge (pre-IEEE 802.1ad) ports.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.5
opticsIMEthFCSDiscardErroredFramesIf this object is set to TRUE, the incoming errored Ethernet frames are discarded, if it is set to FALSE the incoming errored Ethernet frames are forwarded as the correct ones.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.6
opticsIMEthDefaultPauseThis object identifies the default administrative PAUSE type. When the underlying layer is mau, this object represent the administratively-configured type of Flow Control operations supported by the Ethernet port. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the Flow Control. In this case, a set to this object will force the Flow Control into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the Flow Control is determined by the auto-negotiation, and the value of this object denotes the type to which the Flow Control will automatically revert if/when auto-negotiation is later disabled. When the underlying layer is not mau, this object can be set only to the disabled (0) value.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.7
opticsIMEthClientTypeIt is used to determine the transmission direction of the frames received from the Ethernet Port. - ETS (1) the frame will be sent to ETS Layer. - ETB (2) the frame will be sent to Ethernet Switch Layer. - LINKAGG (3) the frame will be sent to Link Aggregation Layer. - ELP (4) the frame will be sent to Link Protection Group. - PNP (5) the frame will be sent to PBB Provider Network Portrw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.8
opticsIMEthAdmittedFractionalRateThis value indicates the threshold value of admitted bandwidth on this interface and is specified in kilobits per second (Kbps). This value is requested to trigger PAUSE frame generation and is minor or equal to that specified in ifSpeed.rw
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.9
opticsIMEthLayer2ProtocolListThis parameter enables to choose if to tunnel, toward a Provider Network, or filter Layer 2 Control frames. If the bit is 1 it indicates that the relative frame will be tunneled otherwise if 0 it will be discarded. Default value is all bits set to 1, so tunneling everything. This parameter is significant only if the opticsIMEthClientType is 'ets'.rw
OpticsIMLayer2ProtocolList (OpticsIMETS-MIB)
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.10
opticsIMEthMaclIndexThis object value is the pointer to an entry of opticsIMaclMacTable, representing MACL table.By default the value is zero, indicating no pointer to MACL tablerw
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.11
opticsIMEthPortProfileThe opticsIMEthPortProfile indicates the capabilities and specific or particular behaviour provided by the Ethernet port which managers have to take into account. The default value is the empty string, it means that no peculiarities are present.ro
PortProfile
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.12
opticsIMEthETSServiceTypeIt is used to specify Ethernet Service configuration for an Ethernet Port with ets as Client Type. - Other (0) Ethernet Port supports a generic ETS-flow based Ethernet service with any InFlow Service Type value and any OutFlow Server Type value - ETSVirtualSwitch (1) Ethernet Port supports a 2-Ports ETS Virtual Switch service with Ethernet as unique admitted InFlow Service Type and unique admitted OutFlow Server Type - PortToPort (2) Ethernet Port supports a Port-to-Port Service with Ethernet as Service Type of unique admitted InFlow and Ethernet as Server Type of unique admitted OutFlow. Default value is Other(0)rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.13
opticsIMEthETSServiceStatusThis attribute reports the actual status of those ETS Service types defined over Ethernet Ports with ets as Client Type. This attribute is meaningless in case of Other as ETS Service type. When opticsIMEthETSServiceType is different from Other, the value of this object is: - 0 if ETS Service Type over this EthernetPort is not yet active; - the ifIndex of the peer ETS Service aware port, if ETS Service Type over that Ethernet Port is active.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.14
opticsIMEthCirOverbookingFactorThis attribute defines the overbooking (OB) factor for the CIR BW. The overbooking factor is defined as a percentile. The overbooked CIR BW is calculated as OB CIR BW = (CIR BW * 'opticsIMEthCirOverbookingFactor/ 100). When the value of 'opticsIMEthCirOverbookingFactor' is equal to 100 it means that the OB CIR BW = CIR BW. When the value of 'opticsIMEthCirOverbookingFactor' is equal to 0 it means unlimited overbooking i.e. effectively CoS is set as Best Effort.rw
Unsigned32 (0|100..10000) UNITS "percentile"
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.15
opticsIMEthEirOverbookingFactorThis attribute defines the overbooking (OB) factor for the EIR BW. EIR BW is calculated as EIR = PIR BW - CIR BW. The overbooking factor is defined as a percentile. The overbooked EIR BW is calculated as OB EIR BW = (EIR BW * 'opticsIMEthEirOverbookingFactor/ 100). When the value of 'opticsIMEthEirOverbookingFactor' is equal to 100 it means that the OB CIR BW = CIR BW. When the value of 'opticsIMEthEirOverbookingFactor' is equal to 0 it means unlimited overbooking i.e. effectively CoS is set as Best Effort.rw
Unsigned32 (0|100..10000) UNITS "percentile"
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.16
opticsIMEthAutomaticTxShutdownThis parameter enable the automatic shutdown of the Tx in case a LOS is detected in Rx.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.17
opticsIMEthWaitForDetectionThis parameter specifies how long the Tx is maintained down after LOS is detected in Rx; the parameter is expressed in number of 100ms (the admitted WTR range is 100ms - 10s).rw
Gauge32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.18
opticsIMStormcontrolPointerThis object is pointed to opticsIMStormcontrolIndex. By default the value is zero, indicating no pointer to opticsIMStormCtlTablerw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.19
opticsIMPacketFilteringPointerThe index of packet filtering profile. By default the value is zero, indicating no pointer to opticsIMPksFilteringTablerw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.20
opticsIMEthForcedOutgoingSSMThis object indicates outgoing SSM value for a local Ethernet port. The following values shall be supported: 100: NONE (Disabled Transmission of ESMC Messages) - Default value 0: AUTO (Automatic outgoing SSM value) In case of forced outgoing SSM value - 1: QL-PRC - 2: QL-SSU_A - 3: QL-SSU_B - 4: QL-EEC Option 1 - 5: DNUrw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.21
opticsIMEthHoldOffModeThis object indicates if for the Ethernet interface, involved on a ERP Topology, it has to be applied the hold off time for the ERP protection.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.22
opticsIMEthLosEPSSwitchCriteriaThis object specifies if the LOS of the Ethernet interface, hosted by a board involved on a Equipment Protection Group, is used as switch criteria.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.23
opticsIMEthHwFailConsActThis object specifies the behaviour of the Ethernet interface in case the hosted equipment item is in hardware fail condition. In this case the Ethernet interface can try going on trasmitting signal, i.e. holdon (0) value, or shutting down the transmitter, i.e. shutdown (1) value. Default value is holdon (0). This object applies to the physical interface, either optical or electrical.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.24
opticsIMEthAFRCompensationThe data encapsulation of traffic from UNI to MPLS NNI, will be processed by NE to remove or add some overhead according to flow classification and related policy. Below is key Ethernet data encapsulation used with whole data path from UNI to MPLS NNI: L1 Ethernet Packet include: Preamble,SFD, L2 Ethernet Frame, IPG. This is typical characteristics at physical Ethernet Interface for UNI. L2 Ethernet Frame include: MAC DA/SA,optional 802.1ad/8021q VLAN tag,EtherType,Payload and FCS fields. This is typical characteristics processed by Switch. L1 MPLS Packet include: Preamble, SFD, MAC DA/SA, optional VLAN Tag,EtherType, TUNNEL label, PW label,Optional CW, L2 Ethernet Frame (with optional VLAN operation), IPG. This is typical characteristics at physical Ethernet Interface for MPLS NNI. AFR (admitted fractional Rate),referred as opticsIMEthAdmittedFractionalRate, is based on the traffic metering to trigger pause generation when AFR is reached. The default metering of traffic is applicable for L2 Ethernet frame, which remove 20bytes Preamble/SFD/IPG packet from L1 Ethernet Packet at physical interface, i.e. not based on metering of ifSpeed (refer to opticsIMEthAdmittedFractionalRate description). This de facto behaviour is deviated from AFR original definition. When AFR is applicable for bandwidth shaping with Ingress or Egress physical interface, the removed or appended Overhead versus Ethernet Frame shall be compensated to calibrate the traffic metering mechanism to reflect the traffic rate at Ingress or Egress interface based on the measurement of Ethernet Frames of ingress traffic per port. The value of opticsIMEthAFRCompensation, is defined to indicate the additional byte number shall be taken into account of metering of traffic rate. In order to calibration of traffic rate to ingress physical interface speed, i.e. Ethernet packet rate, 20 bytes (Preamble/SFD/IPG) shall be compensated; In order to calibration of traffic rate to Egress MPLS physical interface speed, i.e. MPLSIF packet rate, below added bytes shall be compensated: Ingress ETS flow VLAN operation (Optional) +4 bytes/VLAN Push -4 bytes/VLAN PoP PW CW (Optional) +4 bytes/enable mode MPLS frame +22bytes(DA/SA/EtherType/TUNNEL label/PW label) L2 encapsulation (Optional) +4 bytes(802.1Q or 802.1ad VLAN tag) Ethernet Packet Overhead +20bytes(Preamble/SFD/IPG) Without the compensation of this value, the AFR indicates the threshold value of admitted bandwidth for Ingress traffic measured with Ethernet Frame. With the compensation of this value, the Admitted fractional rate indicates the threshold value of admitted bandwidth for ingress or egress traffic measured with Ethernet Packet on the associated Ingress or Egress physical Interface. The default value shall be 0 to compatible with previous MIB definition.rw
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.1.1.25
opticsIMEthVLANTypeIndexNextThis object contains an appropriate value to be used for opticsIMEthVLANTypeIndex when creating entries in the opticsIMEthVLANTypeTable. The value 0 indicates that no unassigned entries are available. To obtain the opticsIMEthVLANTypeIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.2
opticsIMEthVLANTypeTableA table containing vendor-specific profiles of the EtherType values used to support provider-bridge VLAN tags (or stacked VLAN).
SEQUENCE OF OpticsIMEthVLANTypeEntry
.1.3.6.1.4.1.637.54.1.25.2.1.3
opticsIMEthVLANTypeEntry
OpticsIMEthVLANTypeEntry
.1.3.6.1.4.1.637.54.1.25.2.1.3.1
opticsIMEthVLANTypeIndexIndex for a row in the opticsIMEthVLANTypeTable. The range is 1...MAXVlanType, where MAXVlanType is product dependent.
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.3.1.1
opticsIMEthVLANTypeEtherTypeThe value of the EtherType field. The default value is the IEEE 802.1Q standard value 0x8100.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.3.1.2
opticsIMEthVLANTypeUserLabelThe user label assigned to this EtherType profile.rw
OpticsIMUserLabel (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.3.1.3
opticsIMEthVLANTypeRowStatusIt is used to create, delete, activate and deactivate a row in the opticsIMEthVLANTypeTable.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.3.1.4
opticsIMifMauExtTableThis table contains extension objects of the ifMauTable.
SEQUENCE OF OpticsIMifMauExtEntry
.1.3.6.1.4.1.637.54.1.25.2.1.4
opticsIMifMauExtEntryAn entry of the opticsIMifMauExtTable.
OpticsIMifMauExtEntry
.1.3.6.1.4.1.637.54.1.25.2.1.4.1
opticsIMifMauExtAsapIndexThis object defines tha ASAP object associated to the MAU interface.rw
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.1
opticsIMifMauExtOpticalChannelTypeIt is used to determine the type of Optical Channel carrying Ethernet interface and associated to the MAU interfacero
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.2
opticsIMifMauExtOpticalChannelLambdaThis object reports lambda (in nm) for optical channel (BlackWhite optical channel, Lambda optical channel) carrying Ethernet interface and associated to the MAU interface.ro
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.3
opticsIMifMauExtOpticalChannelSpacingThis object reports channel spacing (in nm) for colored optical channels carrying Ethernet interfacero
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.4
opticsIMifMauExtCrossoverModeThe opticsIMifMauExtCrossoverMode configures the mode of the positioning of trasmitter and receiver respect to the line: - automatic, with value equal to 1 (default value) means the positioning is performed in automatic way; - mdI, with value equal to 2, means tx and rx are as for DCE (e.g. Hub or switch); - mDIX, with value equal to 3, means they are reverted just as for DTE (e.g. PC).rw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.5
opticsIMifMauExtCrossoverStateThe opticsIMifMauExtCrossoverMode indicates, if possible, the positioning of trasmitter and receiver respect to the line: - unknown, with value equal to 1, if not identifiable - mdI, with value equal to 2, means tx and rx are as for DCE (e.g. Hub or switch) - mDIX, with value equal to 3, means they are reverted just as for DTE (e.g. PC).ro
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.6
opticsIMifMauExtOpticalLinkLengthThis object reports the link length (in m) supported for optical channel carrying Ethernet interface and associated to the MAU interfacero
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.7
opticsIMifMauExtSynchOperationModeIt is used to define the Operation Mode (G.8264) of an Ethernet interface with the following values: - synchronous (1) the interface is belonging to a NE with system clock (EEC) and it should be used for synchronization purpose; in this case the opticsIMifMauExtSynchRole object has to be defined as 'master' or 'slave' value. - asynchronous (2) the interface is not belonging to a NE with system clock (EEC); in this case the opticsIMifMauExtSynchRole object could assume any value incuding 'auto' value (default).rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.8
opticsIMifMauExtSynchRoleA value that uniquely identifies the synchronization role of the Ethernet interface (1000Base-T) advertised by the local auto-negotiation entity. The 'auto' value is not allowed in case the opticsIMifMauExtSynchOperationMode is set to 'synchronous' value.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.9
opticsIMifMauExtOpticalReceivedSignalLevelThis object represents the local received power level. It is a negative integer with associated measure unit expressed in one tenth of dBm.ro
INTEGER (-1000..0)
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.10
opticsIMifMauExtDirectionModeIt is used to define the Interface Direction Mode (IEEE 802.3 clause 66) of an Ethernet interface with the following values: - unidirectional (1) When the interface detects an incoming failure (e.g., LOS), it keeps transmitting traffic in the outgoing direction and also inserts a remote failure indication, if such an indication is defined for that type of MAU (e.g., an RFI signal), to the remote interface. - bidirectional (2) When the interface detects an incoming failure (e.g., LOS), it stops transmitting traffic in the outgoing direction and also inserts a remote failure indication, if such an indication is defined for that type of MAU (e.g., an RFI signal), to the remote interface.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.11
opticsIMifMauExtOpticalTransmittedSignalLevelThis object represents the local transmitted power level. It is an integer with associated measure unit expressed in one tenth of dBm.ro
INTEGER (-1000..1000)
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.12
opticsIMifMauExtEthernetComplianceThis object reports the Ethernet Compliance (MAU type) supported by the physical module hosting this interface.ro
AutonomousType (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.13
opticsIMifMauExtSynchRoleResultA value that uniquely identifies the synchronization role of the Ethernet interface as the result of the auto-negotiatiation between local and peer entities. 'none' value in case auto-negotiation fail. 'notRelevant' in case of syncronization role not meaning the the Ethernet interface (optical).rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.4.1.14
opticsIMEthConfExtTableThis table contains extension objects of the opticsIMEthConfTable.
SEQUENCE OF OpticsIMEthConfExtEntry
.1.3.6.1.4.1.637.54.1.25.2.1.5
opticsIMEthConfExtEntryAn entry of the opticsIMEthConfExtTable.
OpticsIMEthConfExtEntry
.1.3.6.1.4.1.637.54.1.25.2.1.5.1
opticsIMEthConfExtlbLineThis object specifies if the line loopback is active or not. The default value is FALSErw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.5.1.1
opticsIMEthConfExtlbInternalThis object specifies if the internal loopback is active or not. The default value is FALSErw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.5.1.2
opticsIMEthConfExtRemCsfMAUActionThis object identifies the consequent action triggered on local Interface egress port in front of Client failures detection for port-to-port application. - disabled (0) is defined to perform no consequent actions. - transmitter_shutdown (1) is defined to trigger forced transmitter shut-down action. If the interface is not involved in a port-to-port application this consequent action will never be triggered. The default value is disabledrw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.5.1.3
opticsIMEthConfExtMirrorTypeThe port can be configured acting as a mirroring port: the available values are: 0 = no mirroring (the default value) 1 = mirroring a port input 2 = mirroring a port output 3 = BOTH input and output mirroringrw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.5.1.4
opticsIMEthConfExtMirrorPortSelectThis object points to an entry in the ifTable that represents the the port that is mirrored by the port identified by this entry of the opticsIMEthConfExtTable. The default value is 0 (zero) that means no port mirroredrw
InterfaceIndexOrZero (IF-MIB)
.1.3.6.1.4.1.637.54.1.25.2.1.5.1.5
opticsIMEthConfExtCsfMAUActionThis object identifies the consequent action triggered on local Interface egress port for port-to-port application in front of received CSF Frame indications (due to detected remote Ethernet PHY Interface failures). The choice of enabled CSF consequent actions is allowed to be different from SSF consequent actions (consequent actions coping with SDH network failures). disabled (0) is defined to perform no consequent actions. transmitter_shutdown (1) is defined to trigger forced transmitter shut-down action. If the interface is not involved in a port-to-port application, this consequent action will never be triggered. The default value is disabledrw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.5.1.6
opticsIMEthConfExtSsfMAUActionThis object identifies the consequent action triggered on local Interface egress port for port-to-port application in front of Server Layer (e.g.SDH network) failures. The choice of enabled SSF consequent actions is allowed to be different from CSF consequent actions (consequent actions coping with in front of 'Far-end Client Signal Fail (CSF) indications'). disabled (0) is defined to perform no consequent actions. transmitter_shutdown (1) is defined to trigger forced transmitter shut-down action. If the interface is not involved in a port-to-port application, this consequent action will never be triggered. The default value is disabledrw
INTEGER
.1.3.6.1.4.1.637.54.1.25.2.1.5.1.7
opticsIMaclNextIndexThis object contains an appropriate value to be used for opticsIMaclIndex when creating entries in the opticsIMaclTable. The value 0 indicates that no unassigned entries are available. To obtain the opticsIMaclIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index.ro
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.6
opticsIMaclMacAceIndexNextThis object contains an appropriate value to be used for opticsIMaclMacAceIndex when creating entries in the opticsIMaclMacAceTable. The value 0 indicates that no unassigned entries are available. To obtain the opticsIMaclMacAceIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassignedro
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.7
opticsIMaclTableThe table representing the MAC acl. The table references through the index ifIndex the classifier entry associated to the Ethernet port(interface) which the MAC acl applies to.
SEQUENCE OF OpticsIMAclMacEntry
.1.3.6.1.4.1.637.54.1.25.2.1.8
opticsIMAclMacEntryMAC acl entry
OpticsIMAclMacEntry
.1.3.6.1.4.1.637.54.1.25.2.1.8.1
opticsIMaclIndexThe unique index of an ACE within an ACL
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.8.1.1
opticsIMaclNameThe name of an ACL. Within a feature the name is unique used to identifies the list to which the entry belongs in the devicerw
OpticsIMUserLabel (TSDIM-SNMP-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.8.1.2
opticsIMaclApplyChangeA flag to indicate when the changes to the acl are terminated and are applied. When an acl modification is on going, the attribute is equal to false for indicating that the on going changes are not applied.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.8.1.3
opticsIMaclStatusThe status of this ACL conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once a row becomes active, value in any other column within such row cannot be modified.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.8.1.4
opticsIMaclPortIndicatorAssociationThe indication of any interface association. The default value is false. When any port is associated to ACL entry, the agent changes this value to true. This value is changed again to false, when the ACL entry is nomore associated to any interfacero
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.8.1.5
opticsIMaclMacAceTableThe conceptual table of all of aclMacAceEntry
SEQUENCE OF OpticsIMAclMacAceEntry
.1.3.6.1.4.1.637.54.1.25.2.1.9
opticsIMaclMacAceEntryThe conceptual row for aclMacAceTable.
OpticsIMAclMacAceEntry
.1.3.6.1.4.1.637.54.1.25.2.1.9.1
opticsIMaclMacAceIndexThe unique index of an ACE within an ACL
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.1
opticsIMaclMacAceOrderSpecifies the order of execution of ACE within an ACLrw
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.2
opticsIMaclMacAceActionThe action to be executed, if the condition of the ace is verifiedrw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.3
opticsIMaclMacAceSourceMacAddrIt indicates the 48 bits source MAC address. The specified source mac of the packet. The packet's source mac address is AND-ed with the value of aceMacSourceMacAddrBitmask and then compared against the value of this object.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.4
opticsIMaclMacAceSourceMacAddrBitmaskThe specified source mac address mask. If it is not configured, the default value is all 1rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.5
opticsIMaclMacAceDestMacAddrIt indicates the 48 bits destination MAC address. The specified destination mac of the packet The packet's destination mac address is AND-ed with the value of aceMacDestMacAddrBitmask and then compared against the value of this object.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.6
opticsIMaclMacAceDestMacAddrBitmaskThe specified destination mac address mask. If it is not configured, the default value is all 1rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.7
opticsIMaclMacAceVidIndicates the 12 bits of the VLAN Identifier value.rw
OpticsIMETSVlanCfg (OpticsIMETS-MIB)
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.8
opticsIMaclMacAceVidRangeThe specified VLAN Identifier offset. The packet's VLAN Identifier has to be included between aclMacAceVid and this value plus aclMacAceVidRange; if VLAN Identifier range is not configured, 0 is the value of this object.rw
Gauge32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.9
opticsIMaclMacAceEtherTypeIndicates the 16 bits of the EtherType value.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.10
opticsIMaclMacAceEtherTypeRangeThe specified EthernetType offset: the packet's Ethertype has to be included between aclMacEhtertype and this value plus aclMacAceEtherTypeRange; if the Ethertype range is not configured, 0 is the value of this object.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.11
opticsIMaclMacAceStatusThe status of this mac ACE conceptual row entry. This object is used to manage creation, deletion and modification of rows in this table. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once a row becomes active, value in any other column within such row cannot be modified.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.12
opticsIMaclMacAceVidBitmaskThe specified Vid mask. If it is not configured, the default value is all 1rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.13
opticsIMaclMacAceEtherTypeBitmaskThe specified EtherType mask. If it is not configured, the default value is all 1rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.14
opticsIMaclMacAcePriorityIndicates the 8 bits of the 802.1p priority bits value. The specified 802.1p priority bits value of the packet. The packet's 802.1p priority bits value is AND-ed with the value of opticsIMaclMacAcePriorityBitMask and then compared against the value of this object.rw
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.15
opticsIMaclMacAcePriorityBitMaskThe specified 802.1p Priority mask. If it is not configured, the default value is all 1rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.16
opticsIMaclMacAceSourceIPV4AddrIt indicates the 32 bits source IP address. The specified source IP of the packet is AND-ed with the value of opticsIMaclMacAceSourceIPV4AddrBitmask and then compared against the value of this object.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.17
opticsIMaclMacAceSourceIPV4AddrBitmaskThe specified source IPv4 address mask. If it is not configured, the default value is all 1.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.18
opticsIMaclMacAceDestIPV4AddrIt indicates the 32 bits destination IPv4 address. The specified destination IPv4 address is AND-ed with the value of opticsIMaclMacAceDestIPV4AddrBitmask and then compared against the value of this object.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.19
opticsIMaclMacAceDestIPV4AddrBitmaskThe specified destination IPv4 address mask. If it is not configured, the default value is all 1.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.20
opticsIMaclMacAceIpDscpIt indicates IP DSCP valuerw
OpticsIMETSIpDscp (OpticsIMETS-MIB)
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.21
opticsIMaclMacAceIpDscpRangeThe specified DSCP Identifier offset. The packet's DSCP has to be included between aclMacAceIpDscp and this value plus aclMacAceIpDscpRange; if IP DSCP range is not configured, 0 is the value of this object.rw
Gauge
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.22
opticsIMaclMacAceIpDscpBitMaskThe specified DSCP mask. If it is not configured, the default value is all 1rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.23
opticsIMaclMacAceSourceTcpPortIndicates the Source TCP Port value.The default value is 65537(don't care)rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.24
opticsIMaclMacAceMaxSourceTcpPortIndicates the max value of Source TCP Port. Default value:0.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.25
opticsIMaclMacAceDestTcpPortIndicates the Dest TCP Port value.The default value is 65537(don't care)rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.26
opticsIMaclMacAceMaxDestTcpPortIndicates the max value of Dest TCP Port. Default value:0.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.27
opticsIMaclMacAceSourceUdpPortIndicates the Source UDP Port value.The default value is 65537(don't care)rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.28
opticsIMaclMacAceMaxSourceUdpPortIndicates the max value of Source UDP Port. Default value:0.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.29
opticsIMaclMacAceDestUdpPortIndicates the Dest UDP Port value.The default value is 65537(don't care)rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.30
opticsIMaclMacAceMaxDestUdpPortIndicates the max value of Dest UDP Port. Default value:0.rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.31
opticsIMaclMacAceSourceIPV6AddrIt indicates the 128 bits source IPV6 address. The specified source IP of the packet is AND-ed with the value of opticsIMaclMacAceSourceIPV6AddrBitmask and then compared against the value of this object.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.32
opticsIMaclMacAceSourceIPV6AddrBitmaskThe specified source IPv6 address mask. If it is not configured, the default value is all 1.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.33
opticsIMaclMacAceDestIPV6AddrIt indicates the 128 bits destination IPv6 address. The specified destination IPv6 address is AND-ed with the value of opticsIMaclMacAceDestIPV6AddrBitmask and then compared against the value of this object.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.34
opticsIMaclMacAceDestIPV6AddrBitmaskThe specified destination IPv6 address mask. If it is not configured, the default value is all 1.rw
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.35
opticsIMaclMacAceProtocolId8 bits Protocol Identifier value in IPV4 Header (or 8 bits Next Header value in IPv6 Header). Default value:255rw
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.9.1.36
opticsIMaclActualMacAceTableThe conceptual read-only table of all of aclMacAceEntry
SEQUENCE OF OpticsIMAclActualMacAceEntry
.1.3.6.1.4.1.637.54.1.25.2.1.10
opticsIMAclActualMacAceEntryThe conceptual read-only row for aclMacAceTable.
OpticsIMAclActualMacAceEntry
.1.3.6.1.4.1.637.54.1.25.2.1.10.1
opticsIMAclActualMacAceIndexThe unique index of an ACE within an ACL
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.1
opticsIMAclActualMacAceOrderSpecifies the order of execution of ACE within an ACLro
Integer32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.2
opticsIMAclActualMacAceActionThe action to be executed, if the condition of the ace is verifiedro
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.3
opticsIMAclActualMacAceSourceMacAddrIt indicates the 48 bits source MAC address. The specified source mac of the packet The packet's source mac address is AND-ed with the value of aceMacSourceMacAddrBitmask and then compared against the value of this object.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.4
opticsIMAclActualMacAceSourceMacAddrBitmaskThe specified source mac address mask. If it is not configured, the default value is all 1ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.5
opticsIMAclActualMacAceDestMacAddrIt indicates the 48 bits destination MAC address. The specified destination mac of the packet The packet's destination mac address is AND-ed with the value of aceMacDestMacAddrBitmask and then compared against the value of this object.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.6
opticsIMAclActualMacAceDestMacAddrBitmaskThe specified destination mac address mask. If it is not configured, the default value is all 1ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.7
opticsIMAclActualMacAceVidIndicates the 12 bits of the VLAN Identifier value.ro
OpticsIMETSVlanCfg (OpticsIMETS-MIB)
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.8
opticsIMAclActualMacAceVidRangeThe specified VLAN Identifier offset. The packet's VLAN Identifier has to be included between aclMacAceVid and this value plus aclMacAceVidRange; if VLAN Identifier range is not configured, 0 is the value of this object.ro
Gauge32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.9
opticsIMAclActualMacAceEtherTypeIndicates the 16 bits of the EtherType value.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.10
opticsIMAclActualMacAceEtherTypeRangeThe specified EthernetType offset: the packet's Ethertype has to be included between aclMacEhtertype and this value plus aclMacAceEtherTypeRange; if the Ethertype range is not configured, 0 is the value of this object.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.11
opticsIMaclActualMacAceVidBitmaskThe specified Vid maskro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.12
opticsIMaclActualMacAceEtherTypeBitmaskThe specified EtherType mask.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.13
opticsIMaclActualMacAcePriorityIndicates the 8 bits of the 802.1p priority bits value. The specified 802.1p priority bits value of the packet. The packet's 802.1p priority bits value is AND-ed with the value of opticsIMaclMacAcePriorityBitMask and then compared against the value of this object.ro
Enumeration
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.14
opticsIMaclActualMacAcePriorityBitMaskThe specified 802.1p Priority mask. If it is not configured, the default value is all 1ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.15
opticsIMaclActualMacAceSourceIPV4AddrIt indicates the 32 bits source IP address.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.16
opticsIMaclActualMacAceSourceIPV4AddrBitmaskThe specified source IPv4 address mask.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.17
opticsIMaclActualMacAceDestIPV4AddrIt indicates the 32 bits destination IPv4 address.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.18
opticsIMaclActualMacAceDestIPV4AddrBitmaskThe specified destination IPv4 address mask.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.19
opticsIMaclActualMacAceIpDscpIt indicates IP DSCP valuero
OpticsIMETSIpDscp (OpticsIMETS-MIB)
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.20
opticsIMaclActualMacAceIpDscpRangeThe specified DSCP Identifier offset.ro
Gauge
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.21
opticsIMaclActualMacAceIpDscpBitMaskThe specified DSCP mask.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.22
opticsIMaclActualMacAceSourceTcpPortIndicates the Source TCP Port value.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.23
opticsIMaclActualMacAceMaxSourceTcpPortIndicates the max value of Source TCP Port.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.24
opticsIMaclActualMacAceDestTcpPortIndicates the Dest TCP Port value.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.25
opticsIMaclActualMacAceMaxDestTcpPortIndicates the max value of Dest TCP Port.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.26
opticsIMaclActualMacAceSourceUdpPortIndicates the Source UDP Port value.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.27
opticsIMaclActualMacAceMaxSourceUdpPortIndicates the max value of Source UDP Portro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.28
opticsIMaclActualMacAceDestUdpPortIndicates the Dest UDP Port value.ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.29
opticsIMaclActualMacAceMaxDestUdpPortIndicates the max value of Dest UDP Portro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.30
opticsIMaclActualMacAceSourceIPV6AddrIt indicates the 128 bits source IPV6 address. The specified source IP of the packet is AND-ed with the value of opticsIMaclMacAceSourceIPV6AddrBitmask and then compared against the value of this object.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.31
opticsIMaclActualMacAceSourceIPV6AddrBitmaskThe specified source IPv6 address mask.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.32
opticsIMaclActualMacAceDestIPV6AddrIt indicates the 128 bits destination IPv6 address. The specified destination IPv6 address is AND-ed with the value of opticsIMaclMacAceDestIPV6AddrBitmask and then compared against the value of this object.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.33
opticsIMaclActualMacAceDestIPV6AddrBitmaskThe specified destination IPv6 address mask.ro
OCTET STRING
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.34
opticsIMAclActualMacAceProtocolIdIndicates 8 bits Protocol Identifier value in IPV4 Header (or 8 bits Next Header value in IPv6 Header)ro
Unsigned32
.1.3.6.1.4.1.637.54.1.25.2.1.10.1.35
opticsimEthNEMCConf
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.25.99.2
opticsimEthNEMCCompl
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.25.99.2.1
opticsimEthNEMCGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.637.54.1.25.99.2.2
OPTICSIM-ETHNE-MIB - SNMP MIB Reference | MIBs Explorer