NTNTECH-NMS-TRAPS-V1-MIB
Standard SNMP MIB module defining data structures for NTNTECH-NMS-TRAPS-V1-MIB.
Imported Objects
Objects
5 total| Object Name |
|---|
RFC-1212There has been a change in the Fan state. TRAP-TYPE .1.3.6.1.4.1.8059.1.3.0.1001 |
envTempNormal-v1The normal operating temperature inside the chassis has returned.
Note: This trap applies to the micro DSLAMs only. TRAP-TYPE .1.3.6.1.4.1.8059.1.3.0.1002 |
envTempExceeded-v1The normal operating temperature inside the chassis has been exceeded.
Note: This trap applies to the micro DSLAMs only. TRAP-TYPE .1.3.6.1.4.1.8059.1.3.0.1003 |
invIfModPresentTrap-v1A change was detected related to the population state of a chassis slot. This
trap will be triggered when the population state of a slot makes the transition
from vacant to present, where present is any valid interface module type as
defined by 'ifStaType'. TRAP-TYPE .1.3.6.1.4.1.8059.1.3.0.2001 |
invIfModRemovedTrap-v1A change was detected related to the population state of a chassis slot. This
trap will be triggered when the population state of a slot makes the transition
from present, to vacant. In otherwords, this trap will be triggered if an interface
module of type 'a' is immediately replaced with one of type 'b' or 40 seconds after
an interface module is removed leaving the slot vacant. TRAP-TYPE .1.3.6.1.4.1.8059.1.3.0.2002 |
More MIBs from Paradyne
Browse all ParadyneMIBs →The NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB provides an SNMP API to configure and monitor interface parameters across Paradyne IPD12000, IPD4000, and Mini/Micro DSLAM hardware families, including ADSL, E1, T1, IDSL, and SDSL access multiplexers. It enables management of operational modes (Full Rate, G.lite, CAP, 2B1Q, G.SHDSL) and port-level configurations for 6, 12, and 24-port variants supporting voice and data services.
The NTNTECH-CHASSIS-CONFIGURATION-MIB provides SNMP-based configuration management for Paradyne DSLAM chassis hardware, specifically targeting the MUM200-2, MUM2000-2, and various Mini/Micro SDSL/ADSL models (SMD2000, SuD2011, SuD2002 series). It enables remote monitoring and control of critical chassis parameters, including uplink interface module status (UIM-10/100, UIM-DS3, UIM-E1, UIM-E3, UIM-T1) and line encoding modes (2B1Q, G.SHDSL, G.lite) across these
SNMP MIB module
The NTNTECH-INTERFACE-MODULE-STATUS-MIB provides SNMP access to monitor interface statistics and operational status for Paradyne IPD12000, IPD4000, and various Mini/Micro DSLAM hardware platforms supporting ADSL, E1, T1, IDSL, and SDSL (CAP, 2B1Q, G.SHDSL) line encodings. This module enables the retrieval of specific counter metrics and state indicators for 12-port and 24-port access multiplexer interfaces to facilitate remote troubleshooting and performance analysis of legacy DSL aggregation equipment.
The NTNTECH-CHASSIS-STATUS-MIB provides an SNMP interface for monitoring the operational status and uplink module configurations of Paradyne IPD12000, IPD4000, and Mini/Micro DSLAM chassis. It specifically tracks hardware state variables for ADSL, SDSL, and multiplexer uplink modules (UIM-10/100, DS3, E1, E3, T1) across supported line encoding standards including G.lite, 2B1Q, and G.SHDSL.
SNMP MIB module