NNCEXTSPVC-MIB
This module contains Alcatel CID's proprietary MIB definition for managing Soft Permanent Virtual Connections (SPVCs). This MIB supports the creation, modification, query, and deletion of SPVCs (Soft Permanent Virtual Connections), on Cell Relay (ATM), Frame Relay, and Circuit Emulation endpoints. For Cell Relay-based endpoints, Permanent Virtual Path Connection (PVPC) and Permanent Virtual Channel Connection (PVCC) are supported, while SPVCCs are supported on Frame Relay and Circuit Emulation endpoints.
Cell Relay SPVCs, Frame Relay SPVCs and Circuit Emulation SPVCs are supported in this MIB. SPVCs with any other service types are not supported at this point.
For SPVCs interworking across different endpoint types, CR to FR, FR to CR, CR to CE, CE to CR connections are supported. CE to FR or FR to CE are not suppported.
Operator directed routing for SPVC connections is not supported at this point.
To create an SPVC, the required MIB objects from the destination table must be configured and sent to the destination endpoint. Next, the MIB objects from the source endpoint table (based on the endpoint type and SPVC type - either nncCrSpvpcTable, nncCrSpvccTable, nncFrSpvcTable, or nncCeSpvcTable) are configured and sent to the source endpoint. Assuming a PDU with a RowStatus of 'createAndGo' or 'Active' has been received, if the adminStatus of the SPVC is set to 'enabled', the SPVC will be connected; if the adminStatus of the SPVC is set to 'disabled', the SPVC will be configured but not connected.
SPVC creation SET-REQuests can be sent two ways: using a RowStatus value of 'createAndGo', or using multiple SET-REQs using RowStatus values of 'createAndWait' and 'active'.
Creating an SPVC using rowStatus=createAndWait(5)
In the case of multiple SET-REQs, the RowStatus is set to createAndWait(5) for all but the last SET-REQ, and set to active(1) for the last SET-REQ. The SPVC is configured only after the last PDU (with RowStatus as 'active') is received.
Creating an SPVC using rowStatus=createAndGo(4)
In the other case, all required MIB objects can fit in one SET-REQ. If using only one SET-REQ, the RowStatus should be set to createAndGo(4).
In both cases, default values for MIB objects will be used wherever possible.
To delete an SPVC, the correct table objects must be sent to both the destination endpoint and the source endpoint for the given SPVC, using the correct index, and setting the rowStatus to 'destroy'. This will delete the specified SPVC.
Some abreviations:
abr/ABR/Abr: Available Bit Rate
Bwd: Backward. For traffice descriptors from destination endpoint to source
endpoint (receiving traffic) cbr/CBR/Cbr: Constant Bit Rate
Dst: Destination endpoint
Fwd: Forward. For traffic descriptors from source endpoint to destination endpoint
(transmitting traffic) nt-vbr/nrtvbr/NRT-VBR: Non-Real-Time Variable Bit Rate
Src: Source endpoint
Targ: Target. For the destination endpoint info in source endpoint table
ubr/UBR/Ubr: Unspecified Bit Rate
Main OID:
nncExtSpvc.1.3.6.1.4.1.123.3.82
205
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
205 total| Object Name |
|---|
nncExtSpvcThis module contains Alcatel CID's proprietary MIB definition for managing
Soft Permanent Virtual Connections (SPVCs).
This MIB supports the creation, modification, query, and deletion of SPVCs
(Soft Permanent Virtual Connections), on Cell Relay (ATM), Frame Relay,
and Circuit Emulation endpoints. For Cell Relay-based endpoints,
Permanent Virtual Path Connection (PVPC) and Permanent Virtual
Channel Connection (PVCC) are supported, while SPVCCs are
supported on Frame Relay and Circuit Emulation endpoints.
Cell Relay SPVCs, Frame Relay SPVCs and Circuit Emulation SPVCs are
supported in this MIB. SPVCs with any other service types are not supported
at this point.
For SPVCs interworking across different endpoint types, CR to FR, FR to CR,
CR to CE, CE to CR connections are supported.
CE to FR or FR to CE are not suppported.
Operator directed routing for SPVC connections is not supported at this
point.
To create an SPVC, the required MIB objects from the destination table
must be configured and sent to the destination endpoint. Next,
the MIB objects from the source endpoint table (based on the endpoint
type and SPVC type - either nncCrSpvpcTable, nncCrSpvccTable,
nncFrSpvcTable, or nncCeSpvcTable) are configured and sent to the source
endpoint. Assuming a PDU with a RowStatus of 'createAndGo' or 'Active'
has been received, if the adminStatus of the SPVC is set to 'enabled',
the SPVC will be connected; if the adminStatus of the SPVC is set to
'disabled', the SPVC will be configured but not connected.
SPVC creation SET-REQuests can be sent two ways: using a RowStatus value
of 'createAndGo', or using multiple SET-REQs using RowStatus values of
'createAndWait' and 'active'.
Creating an SPVC using rowStatus=createAndWait(5)
In the case of multiple SET-REQs, the RowStatus is set to createAndWait(5)
for all but the last SET-REQ, and set to active(1) for the last SET-REQ.
The SPVC is configured only after the last PDU (with RowStatus as 'active')
is received.
Creating an SPVC using rowStatus=createAndGo(4)
In the other case, all required MIB objects can fit in one SET-REQ.
If using only one SET-REQ, the RowStatus should be set to createAndGo(4).
In both cases, default values for MIB objects will be used wherever possible.
To delete an SPVC, the correct table objects must be sent to both the
destination endpoint and the source endpoint for the given SPVC,
using the correct index, and setting the rowStatus to 'destroy'.
This will delete the specified SPVC.
Some abreviations:
abr/ABR/Abr: Available Bit Rate
Bwd: Backward. For traffice descriptors from destination endpoint to source
endpoint (receiving traffic)
cbr/CBR/Cbr: Constant Bit Rate
Dst: Destination endpoint
Fwd: Forward. For traffic descriptors from source endpoint to destination endpoint
(transmitting traffic)
nt-vbr/nrtvbr/NRT-VBR: Non-Real-Time Variable Bit Rate
Src: Source endpoint
Targ: Target. For the destination endpoint info in source endpoint table
ubr/UBR/Ubr: Unspecified Bit Rate MODULE-IDENTITY .1.3.6.1.4.1.123.3.82 |
nncExtSpvcObjects OBJECT IDENTIFIER .1.3.6.1.4.1.123.3.82.1 |
nncCrSpvpcTablenncCrSpvpcTable contains all the objects sent to a source
endpoint that are used to create, modify, query and delete
SPVC connections. SEQUENCE OF NncCrSpvpcTableEntry .1.3.6.1.4.1.123.3.82.1.1 |
nncCrSpvpcTableEntryAn entry of nncCrSpvpcTable NncCrSpvpcTableEntry .1.3.6.1.4.1.123.3.82.1.1.1 |
nncCrSpvpcServiceCategoryThis object is used to set the traffic service category. This object
is dependent on the value specified in nncCrSpvpcTrafficDescriptorrw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.1 |
nncCrSpvpcTargEpAddrThis object is used to specify the 20 byte AESA address for
the target endpoint. The address map is as the following:
Byte\Bit 8 7 6 5 4 3 2 1
1-13 byte | 13-byte Internal Subscriber Prefix |
14th byte | I/G | U/L | OUI(most significant 6 bits) |
15th byte | OUI(2nd most significant 8 bits |
16th byte | OUI(3rd most significant 8 bits |
17th byte | Shelf/Slot(1st most significant 8 bits |
18th byte | Shelf/Slot(2nd most significant 8 bits |
19th byte |Flag0| Port |
20th byte | 0 |rw AtmFormatDisplay .1.3.6.1.4.1.123.3.82.1.1.1.2 |
nncCrSpvpcTargVpiThis object contains the virtual path identifier (VPI) value for the
target endpoint. Range: 0 - 4095rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.3 |
nncCrSpvpcAdminStatusThis object accepts two values, enabled (1), and disabled (2).
When the value is disabled, the SPVC is not connected. When
enabled, the SPVC is connected when possible.
Use nncCrSpvpcAdminStatus to determine if the connection is
successful.rw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.4 |
nncCrSpvpcPriorityThis object is used to set the priority for a SPVC connection
request. It ranges between 1-16, with the following values:
Best Priority = 1
Default Priority = 3
Worst Priority = 16rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.5 |
nncCrSpvpcMaxAdminWeightThis object is used to set a cost threshold for an SPVC connection.
If the total cost of all VPCs exceeds this weight value for a given
path, this SPVC will choose an alternative path or give up.
Infinite = -1
Min Admin Weight = 0
Max Admin Weight = 2147483647rw Integer32 (-1..2147483647) .1.3.6.1.4.1.123.3.82.1.1.1.6 |
nncCrSpvpcOperationThis object is used to request a reroute operation. Querying this
object will not provide any useful information.rw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.7 |
nncCrSpvpcCallStatusThis read-only object is used to query the state of a particular SPVC.
SPVCs that are connected and operational will return a value of
'connected', while those that are incomplete or otherwise unable to be
connected will return 'waitingForResources'. SPVCs that are configured
but not yet connected will contain a value of 'readyForConnect'.ro Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.8 |
nncCrSpvpcLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. It can be configured for either the UNI
side or the NNI side, or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.9 |
nncCrSpvpcFwdAbrDynTrfcIcrABR dynamic traffic descriptor's Initial Cell (Information)
Rate for the forward direction.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.10 |
nncCrSpvpcFwdAbrDynTrfcRifABR traffic Rate Increase Factor for the forward direction.
Value is expressed as the -power of 2.
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.11 |
nncCrSpvpcFwdAbrDynTrfcRdfABR traffic Rate Decrease Factor descriptor for the forward direction.
Value is expressed as the -power of 2
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.12 |
nncCrSpvpcBwdAbrDynTrfcIcrABR dynamic traffic descriptor's Initial Cell Rate for the destination
endpoint.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.13 |
nncCrSpvpcBwdAbrDynTrfcRifABR traffic Rate Increase Factor for the backward direction.
Value is expressed as the -power of 2.
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.14 |
nncCrSpvpcBwdAbrDynTrfcRdfABR traffic Rate Decrease Factor descriptor for the backward direction.
Value is expressed as the -power of 2
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.15 |
nncCrSpvpcSrcBillingFlagBilling Configuration for the source endpointrw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.16 |
nncCrSpvpcFwdTmTrafficDescriptorThis object contains the traffic descriptor for the SPVC.
Tag All (1) (UBR using 2k/12k fabric only)
P_0+1 (2) (CBR only)
P_0+1/S_0+1 (3) (NRT/RT-VBR only)
P_0+1/S_0 (4) (NRT/RT-VBR only)
P_0+1/M_0+1 (5) (ABR and UBR only)rw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.17 |
nncCrSpvpcFwdTmPolicingOptionPolicing Option for an SPVPC.
tag is supported only on rt-VBR/nrt-VBR connections that use the
P_0+1/S_0 traffic descriptorrw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.18 |
nncCrSpvpcFwdTmBucketOneRateThis object is for peak cell rate (PCR), the
cell rate which the source may never exceed. It is used
to determine which cells are 'excess'.
Measured in Kb/s.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.19 |
nncCrSpvpcFwdTmBucketOneCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.20 |
nncCrSpvpcFwdTmBucketTwoRateSIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds
the sustained information rate for VBR traffic, and
the minimum information rate for ABR/UBR traffic.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.21 |
nncCrSpvpcFwdTmBucketTwoMbsThis object is for the maximum burst size, in cells,
for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only).
Range: 1 - 10000 cellsrw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.22 |
nncCrSpvpcFwdTmCdvThis value is to set the cell delay variation (CDV) between two
endpoints to support the rt-VBR service category.
Range: 250-10000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.23 |
nncCrSpvpcFwdTmClrThe object is to set the cell loss ratio (CLR) between two SPVC
endpoints when using the nrt-VBR service category.
Value set as 1.0e-#rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.24 |
nncCrSpvpcBwdTmTrafficDescriptorThis object contains the traffic descriptor for the SPVC.
Tag All (1) (UBR using 2k/12k fabric only)
P_0+1 (2) (CBR only)
P_0+1/S_0+1 (3) (NRT/RT-VBR only)
P_0+1/S_0 (4) (NRT/RT-VBR only)
P_0+1/M_0+1 (5) (ABR and UBR only)rw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.25 |
nncCrSpvpcBwdTmPolicingOptionPolicing Option for an SPVPC.
tag is supported only on rt-VBR/nrt-VBR connections that use the
P_0+1/S_0 traffic descriptorrw Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.26 |
nncCrSpvpcBwdTmBucketOneRateThis object is for peak information rate (PIR), the
cell rate which the source may never exceed. It is used
to determine which cells are 'excess'.
Measured in Kb/s.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.27 |
nncCrSpvpcBwdTmBucketOneCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.28 |
nncCrSpvpcBwdTmBucketTwoRateSIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds
the sustained information rate for VBR traffic, and
the minimum information rate for ABR/UBR traffic.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.29 |
nncCrSpvpcBwdTmBucketTwoMbsThis object is for the maximum burst size, in cells,
for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only).
Range: 1 - 10000 cellsrw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.30 |
nncCrSpvpcBwdTmCdvThis value is to set the cell delay variation (CDV) between two
endpoints to support the rt-VBR service category.
Range: 250-10000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.31 |
nncCrSpvpcBwdTmClrThe object is to set the cell loss ratio (CLR) between two SPVC
endpoints when using the nrt-VBR service category.
Value set as 1.0e-#rw INTEGER .1.3.6.1.4.1.123.3.82.1.1.1.32 |
nncCrSpvpcCreatorThe object retrieves the creator of a SPVC connection.ro Enumeration .1.3.6.1.4.1.123.3.82.1.1.1.33 |
nncCrSpvpcRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.1.1.34 |
nncCrSpvpcDstCfgTablethe nncCrSpvpcDstCfg table contains common objects used to
configure, delete, modify and query the destination end
point of an SPVC across different Alcatel CID platforms. SEQUENCE OF NncCrSpvpcDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.2 |
nncCrSpvpcDstCfgTableEntryAn entry of nncCrSpvpcDstCfgTable. NncCrSpvpcDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.2.1 |
nncCrSpvpcDstCfgCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.2.1.1 |
nncCrSpvpcDstCfgPolicingCR Policingrw Enumeration .1.3.6.1.4.1.123.3.82.1.2.1.2 |
nncCrSpvpcDstCfgBillingFlagBilling Configuration for the destination endpoint.rw Enumeration .1.3.6.1.4.1.123.3.82.1.2.1.3 |
nncCrSpvpcDstCfgLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. It can be configured for either the UNI
side or the NNI side, or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.2.1.4 |
nncCrSpvpcDstCfgRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.2.1.5 |
nncCrSpvccTablenncCrSpvccTable contains all the objects sent to a source
endpoint that are used to create, modify, delete
and query Cell Relay SPVC connections. SEQUENCE OF NncCrSpvccTableEntry .1.3.6.1.4.1.123.3.82.1.3 |
nncCrSpvccTableEntryAn entry of nncCrSpvccTable. It contains the objects required
to manage CR SPVCs. NncCrSpvccTableEntry .1.3.6.1.4.1.123.3.82.1.3.1 |
nncCrSpvccServiceCategoryThis object is used to set the traffic service category. This object
is dependent on the value specified in nncCrSpvccTrafficDescriptorrw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.1 |
nncCrSpvccTargEpAddrThis object is used to specify the AESA address for
the target endpoint. The mapping scheme is as follows:
Byte\Bit 8 7 6 5 4 3 2 1
1-13 byte | 13-byte Internal Subscriber Prefix |
14th byte | I/G | U/L | OUI(most significant 6 bits) |
15th byte | OUI(2nd most significant 8 bits |
16th byte | OUI(3rd most significant 8 bits |
17th byte | Shelf/Slot(1st most significant 8 bits |
18th byte | Shelf/Slot(2nd most significant 8 bits |
19th byte |Flag0| Port |
20th byte | 0 |rw AtmFormatDisplay .1.3.6.1.4.1.123.3.82.1.3.1.2 |
nncCrSpvccTargVpiThis object contains the virtual path identifier (VPI) value for the
target endpoint. Range: 0 - 4095rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.3 |
nncCrSpvccTargVciThis object contains the virtual channel identifier (VCI) value for the
target endpoint. Range: 1 - 65535rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.4 |
nncCrSpvccTargDlciThis object contains the data link connection identifier for a frame relay
endpoint. This number is used to identify the target endpoint, and has
only local significance to the specified link.
Range: 16 - 1023 INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.5 |
nncCrSpvccTargCeNumberThis object contains circuit number, channel group number or
both for the Circuit Emulation endpoint. Used in CR to CE connections
when nncCrSpvccTargEpType is configured as circuitEmulation(3).
For CE connections on unchannelized DS3_CCE card, it's the circuit number
1-28 for UDT circuit number
For CE connections on unchannelized E3_CCE card, it's the circuit number
1-16 for UDT circuit number
For CE connections on E1/T1 CES, it's channel group number.
0 for UDT mode, both T1 and E1
1-31 for E1 in SDT mode
1-24 for T1 in SDT mode
For CE connections on channelized DS3_CCE-2 card, it's circuit number
and channel group number combined in the upper and lower byte.
circuitNum (bits 9-16, = 1 to 28 for channelized DS3,
= 0 for unstructured DS3)
channelGroupNum (bits 1-8, = 1 to 24 for SDT mode,
= 0 for UDT Mode)
For CE connections on channelized E3_CCE-2, it's circuit number and
channel group number combined in the upper and lower byte.
circuitNum (bits 9-16, = 1 to 16)
channelGroupNum (bits 1-8, = 1 to 31 for SDT mode,
= 0 for UDT Mode)
Example: Circuit Number = 7, Channel Group = 3 :
nncCrSpvccTargCeNumber = (Circuit Number * 256) +
Channel Group
= 1795
SPVCs across service types other than circuit emulation do not require
this object. INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.6 |
nncCrSpvccTargEpTypeThis object specifies a target endpoint as one of the following types:
cellRelay (1)
frameRelay (2)
circuitEmulation (3)rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.7 |
nncCrSpvccAdminStatusThis object accepts two values, enabled (1), and disabled (2).
When the value is disabled, the SPVC is not connected. When
enabled, the SPVC is connected when possible.
Use nncCrSpvccAdminStatus to determine if the connection is
successful.rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.8 |
nncCrSpvccPriorityThis object is used to set the priority for a SPVC connection
request. It ranges between 1-16, with the following values:
Best Priority = 1
Default Priority = 3
Worst Priority = 16rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.9 |
nncCrSpvccMaxAdminWeightThis object is used to set a cost threshold for an SPVC connection.
If the total cost of all VPCs exceeds this weight value for a given
path, this SPVC will choose an alternative path or give up.
Infinite = -1
Min Admin Weight = 0
Max Admin Weight = 2147483647rw Integer32 (-1..2147483647) .1.3.6.1.4.1.123.3.82.1.3.1.10 |
nncCrSpvccOperationThis object is used to request a reroute operation. Querying this
object will not provide any useful information.rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.11 |
nncCrSpvccCallStatusThis read-only object is used to query the state of a particular SPVC.
SPVCs that are connected and operational will return a value of
'connected', while those that are incomplete or otherwise unable to be
connected will return 'waitingForResources'. SPVCs that are configured
but not yet connected will contain a value of 'readyForConnect'.ro Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.12 |
nncCrSpvccLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. It can be configured for either the UNI
side or the NNI side, or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.13 |
nncCrSpvccFwdAbrDynTrfcIcrABR dynamic traffic descriptor's Initial Cell Rate for the
forward direction.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.14 |
nncCrSpvccFwdAbrDynTrfcRifABR traffic Rate Increase Factor for the forward direction.
Value is expressed as the -power of 2.
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.15 |
nncCrSpvccFwdAbrDynTrfcRdfABR traffic Rate Decrease Factor descriptor for the forward direction.
Value is expressed as the -power of 2
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.16 |
nncCrSpvccBwdAbrDynTrfcIcrABR dynamic traffic descriptor's Initial Cell Rate for the destination
endpoint.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.17 |
nncCrSpvccBwdAbrDynTrfcRifABR traffic Rate Increase Factor for the backward direction.
Value is expressed as the -power of 2.
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.18 |
nncCrSpvccBwdAbrDynTrfcRdfABR traffic Rate Decrease Factor descriptor for the backward direction.
Value is expressed as the -power of 2
Range: 0 - 9rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.19 |
nncCrSpvccSrcBillingFlagBilling Configuration for the source endpointrw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.20 |
nncCrSpvccFwdTmTrafficDescriptorThis object contains the traffic descriptor for the SPVC.
Tag All (1) (UBR using 2k/12k fabric only)
P_0+1 (2) (CBR only)
P_0+1/S_0+1 (3) (NRT/RT-VBR only)
P_0+1/S_0 (4) (NRT/RT-VBR only)
P_0+1/M_0+1 (5) (ABR and UBR only)rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.21 |
nncCrSpvccFwdTmPolicingOptionPolicing Option for an SPVCC.
tag is supported only on rt-VBR/nrt-VBR connections that use the
P_0+1/S_0 traffic descriptorrw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.22 |
nncCrSpvccFwdTmBucketOneRateThis object is for peak cell rate (PCR), the
cell rate which the source may never exceed. It is used
to determine which cells are 'excess'.
Measured in Kb/s.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.23 |
nncCrSpvccFwdTmBucketOneCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.24 |
nncCrSpvccFwdTmBucketTwoRateSIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds
the sustained information rate for VBR traffic, and
the minimum information rate for ABR/UBR traffic.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.25 |
nncCrSpvccFwdTmBucketTwoMbsThis object is for the maximum burst size, in cells,
for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only).
Range: 1 - 10000 cellsrw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.26 |
nncCrSpvccFwdTmCdvThis value is to set the cell delay variation (CDV) between two
endpoints to support the rt-VBR service category.
Range: 250-10000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.27 |
nncCrSpvccFwdTmClrThe object is to set the cell loss ratio (CLR) between two SPVC
endpoints when using the nrt-VBR service category.
Value set as 1.0e-#rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.28 |
nncCrSpvccFwdTmFrameDiscardThe Frame (AAL protocol data unit) Discard option. When enabled,
cells are discarded at the frame level by examining the SDU-type
in the payload type field of the ATM cell header.rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.29 |
nncCrSpvccBwdTmTrafficDescriptorThis object contains the traffic descriptor for the SPVC.
Tag All (1) (UBR using 2k/12k fabric only)
P_0+1 (2) (CBR only)
P_0+1/S_0+1 (3) (NRT/RT-VBR only)
P_0+1/S_0 (4) (NRT/RT-VBR only)
P_0+1/M_0+1 (5) (ABR and UBR only)rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.30 |
nncCrSpvccBwdTmPolicingOptionPolicing Option for an SPVCC.
tag is supported only on rt-VBR/nrt-VBR connections that use the
P_0+1/S_0 traffic descriptorrw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.31 |
nncCrSpvccBwdTmBucketOneRateThis object is for peak cell rate (PCR), the
cell rate which the source may never exceed. It is used
to determine which cells are 'excess'.
Measured in Kb/s.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.32 |
nncCrSpvccBwdTmBucketOneCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.33 |
nncCrSpvccBwdTmBucketTwoRateSIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds
the sustained information rate for VBR traffic, and
the minimum information rate for ABR/UBR traffic.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.34 |
nncCrSpvccBwdTmBucketTwoMbsThis object is for the maximum burst size, in cells,
for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only).
Range: 1 - 10000 cellsrw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.35 |
nncCrSpvccBwdTmCdvThis value is to set the cell delay variation (CDV) between two
endpoints to support the rt-VBR service category.
Range: 250-10000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.36 |
nncCrSpvccBwdTmClrThe object is to set the cell loss ratio (CLR) between two SPVC
endpoints when using the nrt-VBR service category.
Value set as 1.0e-#rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.37 |
nncCrSpvccBwdTmFrameDiscardThe Frame (AAL protocol data unit) Discard option. When enabled,
cells are discarded at the frame level by examining the SDU-type
in the payload type field of the ATM cell header.rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.38 |
nncCrSpvccFrBwdTmArThis object is used to specify the Access Rate, in Kb/s.rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.39 |
nncCrSpvccFrBwdTmCirThe committed Information Rate, in Kb/s.rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.40 |
nncCrSpvccFrBwdTmBcThe Committed Burst Size, in Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.41 |
nncCrSpvccFrBwdTmBeThe Excess Burst Size, in Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.42 |
nncCrSpvccFrBwdTmIwfInterworking Function. Values:
none (None (FR Switching) = 0)
networkInterworking (Network Interworking = 2)
serviceInterworking (Service Interworking = 3)
FFwd Interworking (FFwd Interworking = 4)rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.43 |
nncCrSpvccFrBwdTmPoPolicingrw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.44 |
nncCrSpvccFrBwdTmPacingPacingrw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.45 |
nncCrSpvccFrBwdTmPtclMappingProtocol Mapping for Service Interworking SPVCs.
If Translated Service Interworking is selected,
the a profile must be set using the attribute
nncFrSpvcTmSIWProfile.
Values:
transparent (0),
translated (1) (see also nncFrSpvcTmSIWProfile)rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.46 |
nncCrSpvccFrBwdTmClpMappingCell Loss Priority Mapping.
Values:
cLPEqualsDE (CLP = DE, 0)
cLPEquals0 (CLP = 0, 1 )
cLPEquals1 (CLP = 1, 2 )rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.47 |
nncCrSpvccFrBwdTmDeMappingDiscard Eligibility Mapping
Values:
dEEqualsCLP (DE = CLP, 0)
dESSCSor0 (Network Interworking: DE=FR_SSCS
Service Interworking: DE=0, 1)
dEEquals1 (Service Interworking: DE = 1, 2)
Only the first two values are valid when using
Network Interworking.rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.48 |
nncCrSpvccFrBwdTmEfciMappingExplicit Forward Congestion Indication Mapping
(Applies only to Service Interworking (IWF3), FR to ATM)
Values:
eFCIEqualsFECN (EFCI = FECN, 0)
eFCIEquals0 (EFCI = 0, 1)rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.49 |
nncCrSpvccFrBwdTmPvcMgntProfileEnables or disables the PVC Management Profile.
When enabled, LMI is enabled on the network-side
of the connection.
Used only with FR-CR network interworking selected.rw Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.50 |
nncCrSpvccFrBwdTmSIWProfileThe FR-CR profile index for service interworking connections.
This attribute is used to define the translation profile
to use when a FR to CR SPVC is configured for Translated
Service Interworking (using the attributes nncFrSpvcTmIwf
and nncFrSpvcTmPtclMapping). If the profile selected
isn't defined on the remote node then the connection
will be rejected.
Range: 1 = 16.rw INTEGER .1.3.6.1.4.1.123.3.82.1.3.1.51 |
nncCrSpvccCreatorThe object retrieves the creator of a SPVC connection.ro Enumeration .1.3.6.1.4.1.123.3.82.1.3.1.52 |
nncCrSpvccRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.3.1.53 |
nncCrSpvccDstCfgTablethe nncCrSpvccDstCfg table contains common objects used to
configure, delete, modify and query the destination end
point of an SPVC across different Alcatel CID platforms. SEQUENCE OF NncCrSpvccDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.4 |
nncCrSpvccDstCfgTableEntryAn entry of nncCrSpvccDstCfgTable. NncCrSpvccDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.4.1 |
nncCrSpvccDstCfgCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.4.1.1 |
nncCrSpvccDstCfgPolicingCR Policingrw Enumeration .1.3.6.1.4.1.123.3.82.1.4.1.2 |
nncCrSpvccDstCfgBillingFlagBilling Configuration for the destination endpointrw Enumeration .1.3.6.1.4.1.123.3.82.1.4.1.3 |
nncCrSpvccDstCfgFrVsvdCongestionControlCongestion Control for VS/VD endpoints,
also known as Closed Loop Congestion
Control (CLCC).rw Enumeration .1.3.6.1.4.1.123.3.82.1.4.1.4 |
nncCrSpvccDstCfgLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. It can be configured for either the UNI
side or the NNI side, or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.4.1.5 |
nncCrSpvccDstCfgRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.4.1.6 |
nncFrSpvcTablenncFrSpvcTable contains all the objects sent to a source
endpoint that are used to create, modify, delete
and query FR SPVCCs. SEQUENCE OF NncFrSpvcTableEntry .1.3.6.1.4.1.123.3.82.1.5 |
nncFrSpvcTableEntryAn entry of nncFrSpvcTable. NncFrSpvcTableEntry .1.3.6.1.4.1.123.3.82.1.5.1 |
nncFrSpvcSrcDlciThis object contains the data link connection identifier for a frame relay
endpoint. This number is used to identify the source endpoint, and has
only local significance to the specified link.
Range: 16 - 1023 INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.1 |
nncFrSpvcTargEpAddrThis object contains the target endpoint's 20-byte ATM End System
Address (AESA) proposed by ATM Forum. An endpoint address is created
by appending the switch-wide 13-byte Internal Switch Subscriber
Address Prefix with a 6-byte End Station Identifier (ESI) followed by
a selector byte. The ESI is in IEEE MAC address format and the exact
form depends upon the destination endpoint and the SPVC commissioning
method. The mapping scheme is as follows:
Byte\Bit 8 7 6 5 4 3 2 1
1-13 byte | 13-byte Internal Subscriber Prefix |
14th byte | I/G | U/L | OUI(most significant 6 bits) |
15th byte | OUI(2nd most significant 8 bits |
16th byte | OUI(3rd most significant 8 bits |
17th byte | Shelf/Slot(1st most significant 8 bits |
18th byte | Shelf/Slot(2nd most significant 8 bits |
19th byte |Flag1| Port | Circuit |
20th byte |Circuit(continued) | Stream |rw AtmFormatDisplay .1.3.6.1.4.1.123.3.82.1.5.1.2 |
nncFrSpvcTargDlciThis object contains the data link connection identifier for a frame relay
endpoint. This number is used to identify the target endpoint, and has
only local significance to the specified link.
Range: 16 - 1023rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.3 |
nncFrSpvcTargVpiThis object contains the virtual path identifier (VPI) value for the
Cell Relay based target endpoint. Range: 0 - 4095rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.4 |
nncFrSpvcTargVciThis object contains the virtual channel identifier (VCI) value for the
cell-relay based target endpoint. Range: 1 - 65535rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.5 |
nncFrSpvcTargEpTypeThis object specifies a target endpoint
as one of the following types:
cellRelay (1)
frameRelay (2)rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.6 |
nncFrSpvcAdminStatusThis object accepts two values, enabled (1), and disabled (2).
When the value is disabled, the SPVC is not connected. When
enabled, the SPVC is connected when possible.
Use nncFrSpvcAdminStatus to determine if the connection is
successful.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.7 |
nncFrSpvcPriorityThis object is used to set the priority for a SPVC connection
request. It ranges between 1-16, with the following values:
Best Priority = 1
Default Priority = 3
Worst Priority = 16rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.8 |
nncFrSpvcMaxAdminWeightThis object is used to set a cost threshold for an SPVC connection.
If the total cost of all VPCs exceeds this weight value for a given
path, this SPVC will choose an alternative path or give up.
Infinite = -1
Min Admin Weight = 0
Max Admin Weight = 2147483647rw Integer32 (-1..2147483647) .1.3.6.1.4.1.123.3.82.1.5.1.9 |
nncFrSpvcOperationThis object is used to request a reroute operation. Querying this
object will not provide any useful information.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.10 |
nncFrSpvcCallStatusThis read-only object is used to query the state of a particular SPVC.
SPVCs that are connected and operational will return a value of
'connected', while those that are incomplete or otherwise unable to be
connected will return 'waitingForResources'. SPVCs that are configured
but not yet connected will contain a value of 'readyForConnect'.ro Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.11 |
nncFrSpvcLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. It can be configured for either the UNI
side or the NNI side, or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.12 |
nncFrSpvcSrcBillingFlagBilling Configuration for the source endpoint.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.13 |
nncFrSpvcFrPriorityFrame Relay Priority.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.14 |
nncFrSpvcFrVsvdCongestionControlCongestion Control for VS/VD endpoints,
also known as Closed Loop Congestion
Control (CLCC).rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.15 |
nncFrSpvcFwdFrMirThe FR Src->Dst Minimum Information Rate,
used to set the minimum rate on a CLCC FR-FR
SPVC connection.
If nncFrSpvcFrVsvdCongestionControl is not enabled,
this attribute has no effect.
Range: 0 - 44210 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.16 |
nncFrSpvcFwdTmArThis object is used to specify the Access Rate, in Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.17 |
nncFrSpvcFwdTmCirThe committed Information Rate, in Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.18 |
nncFrSpvcFwdTmBcThe Committed Burst Size, in Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.19 |
nncFrSpvcFwdTmBeExcess Burst Size, Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.20 |
nncFrSpvcTmIwfInterworking Function. Values:
none (None (FR Switching) = 0)
networkInterworking (Network Interworking = 2)
serviceInterworking (Service Interworking = 3)
FFwd Interworking (FFwd Interworking = 4)rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.21 |
nncFrSpvcFwdTmPoPolicing.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.22 |
nncFrSpvcFwdTmPacingPacing.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.23 |
nncFrSpvcTmPtclMappingProtocol Mapping for Service Interworking SPVCs.
If Translated Service Interworking is selected,
the a profile must be set using the attribute
nncFrSpvcTmSIWProfile.
Values:
transparent (0),
translated (1) (see also nncFrSpvcTmSIWProfile)rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.24 |
nncFrSpvcTmClpMappingCell Loss Priority Mapping, for use in FR-CR interworking
SPVCs.
Values:
cLPEqualsDE (CLP = DE, 0)
cLPEquals0 (CLP = 0, 1 )
cLPEquals1 (CLP = 1, 2 )rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.25 |
nncFrSpvcTmDeMappingDiscard Eligibility Mapping, for use in FR-CR interworking
SPVCs.
Values:
dEEqualsCLP (DE = CLP, 0)
dESSCSor0 (Network Interworking: DE=FR_SSCS
Service Interworking: DE=0, 1)
dEEquals1 (Service Interworking: DE = 1, 2)
Only the first two values are valid when using
Network Interworking.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.26 |
nncFrSpvcTmEfciMappingExplicit Forward Congestion Indication Mapping
(Applies only to Service Interworking (IWF3), FR to ATM)
Values:
eFCIEqualsFECN (EFCI = FECN, 0)
eFCIEquals0 (EFCI = 0, 1)rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.27 |
nncFrSpvcTmPvcMgntProfileEnables or disables the PVC Management Profile.
When enabled, LMI is enabled on the network-side
of the connection.
Used only with FR-CR network interworking selected.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.28 |
nncFrSpvcTmSIWProfileThe FR-CR profile index for service interworking connections.
This attribute is used to define the translation profile
to use when a FR to CR SPVC is configured for Translated
Service Interworking (using the attributes nncFrSpvcTmIwf
and nncFrSpvcTmPtclMapping). If the profile selected
isn't defined on the remote node then the connection
will be rejected.
Range: 1 - 16.rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.29 |
nncFrSpvcTmRemapDlciThe source end-point Data Link Connection Identifier
for many-to-one Network Interworking (IWF2) connections.rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.30 |
nncFrSpvcBwdFrMirThe FR Dst->Src Minimum Information Rate, used
on CLCC-enabled connections.
Range: 0 - 44210 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.31 |
nncFrSpvcBwdTmArThis object is used to specify the Access Rate, in Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.32 |
nncFrSpvcBwdTmCirThe committed Information Rate, in Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.33 |
nncFrSpvcBwdTmBcThe Committed Burst Size, in Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.34 |
nncFrSpvcBwdTmBeThe Excess Burst Size, Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.35 |
nncFrSpvcBwdTmPoPolicing.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.36 |
nncFrSpvcBwdTmPacingPacing.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.37 |
nncFrSpvcCrTmServiceCategoryThis object is used to set the traffic service category for SPVC
Connections. This object is dependent on the value specified in
nncFrSpvcCrBwdTmTrafficDescriptor.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.38 |
nncFrSpvcCrBwdTmTrafficDescriptorThis object contains the CR traffic descriptor for a FR-CR SPVC.
Tag All (1) (UBR using 2k/12k fabric only)
P_0+1/S_0+1 (3) (NRT/RT-VBR only)
P_0+1/S_0 (4) (NRT/RT-VBR only)
P_0+1/M_0+1 (5) (ABR and UBR only)rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.39 |
nncFrSpvcCrBwdTmPolicingOptionPolicing Option for a FR SPVC.
tag is supported only on rt-VBR/nrt-VBR connections that use the
P_0+1/S_0 traffic descriptorrw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.40 |
nncFrSpvcCrBwdTmBucketOneRateUsed in FR - CR interworking.
This object is for peak cell rate (PCR), the
cell rate which the cell endpoint may never exceed. It is used
to determine which cells are 'excess'.
Measured in Kb/s.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.41 |
nncFrSpvcCrBwdTmBucketOneCdvtThis object is used to set cell delay variation tolerance (CDVT) for
the CR endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.42 |
nncFrSpvcCrBwdTmBucketTwoRateUsed in FR - CR interworking.
The attribute contains the SIR_0, SIR_0+1 or MIR_0+1.
This parameter holds the sustained information rate
(SIR_0 or SIR_0+1) for VBR traffic, and
the minimum information rate for ABR/UBR traffic.
Range: 0 - 2488320 Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.43 |
nncFrSpvcCrBwdTmBucketTwoMbsThis object is for the maximum burst size, in cells,
for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only).
Range: 1 - 10000 cellsrw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.44 |
nncFrSpvcCrBwdTmCdvThis value is to set the cell delay variation (CDV) at the CR
endpoint. Applicable only when the rt-VBR service category is used.
Range: 250-10000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.45 |
nncFrSpvcCrBwdTmClrThe object is to set the cell loss ratio (CLR) at the CR endpoint of
a FR-CR SPVC. Valid only when using the nrt-VBR service category.
Value set as 1.0e-#rw INTEGER .1.3.6.1.4.1.123.3.82.1.5.1.46 |
nncFrSpvcCrBwdTmFrameDiscardThe Frame (AAL protocol data unit) Discard option. When enabled,
cells are discarded at the frame level by examining the SDU-type
in the payload type field of the ATM cell header.rw Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.47 |
nncFrSpvcCreatorThe object retrieves the creator of a given SPVC connection.ro Enumeration .1.3.6.1.4.1.123.3.82.1.5.1.48 |
nncFrSpvcRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.5.1.49 |
nncFrSpvcDstCfgTablethe nncFrSpvcDstCfg table contains common objects used to
configure, delete, modify and query the destination end
point of an SPVC across different Alcatel CID platforms. SEQUENCE OF NncFrSpvcDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.6 |
nncFrSpvcDstCfgTableEntryAn entry of nncFrSpvcDstCfgTable. NncFrSpvcDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.6.1 |
nncFrSpvcDstCfgTmArThis object is used to specify the Access Rate, in Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.6.1.1 |
nncFrSpvcDstCfgTmCirThe committed Information Rate, Kb/srw INTEGER .1.3.6.1.4.1.123.3.82.1.6.1.2 |
nncFrSpvcDstCfgTmBcThe Committed Burst Size, in Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.6.1.3 |
nncFrSpvcDstCfgTmBeExcess Burst Size, in Kb.rw INTEGER .1.3.6.1.4.1.123.3.82.1.6.1.4 |
nncFrSpvcDstCfgTmIwfInterworking Function. Values:
none (None (FR Switching) = 0)
networkInterworking (Network Interworking = 2)
serviceInterworking (Service Interworking = 3)
FFwd Interworking (FFwd Interworking = 4)rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.5 |
nncFrSpvcDstCfgTmPoPolicing.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.6 |
nncFrSpvcDstCfgTmPacingPacing.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.7 |
nncFrSpvcDstCfgTmPtclMappingProtocol Mapping for Service Interworking SPVCs.
If Translated Service Interworking is selected,
the a profile must be set using the attribute
nncFrSpvcTmPvcMgntProfile.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.8 |
nncFrSpvcDstCfgTmClpMappingCell Loss Priority Mapping.
Values:
cLPEqualsDE (CLP = DE)
cLPEquals0 (CLP = 0 )
cLPEquals1 (CLP = 1 )rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.9 |
nncFrSpvcDstCfgTmDeMappingDiscard Eligibility Mapping
Values:
dEEqualsCLP (DE = CLP, 0)
dESSCSor0 (Network Interworking: DE=FR_SSCS
Service Interworking: DE=0, 1)
dEEquals1 (Service Interworking: DE = 1, 2)
Only the first two values are valid when using
Network Interworking.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.10 |
nncFrSpvcDstCfgTmEfciMappingExplicit Forward Congestion Indication Mapping
(Applies only to Service Interworking (IWF3), FR to ATM)
Values:
eFCIEqualsFECN (0)
eFCIEquals0 (1)rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.11 |
nncFrSpvcDstCfgTmPvcMgntProfileEnables or disables the PVC Management Profile.
When enabled, LMI is enabled on the network-side
of the connection.
Used only with FR-CR network interworking selected.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.12 |
nncFrSpvcDstCfgTmSIWProfileThe FR-CR profile index for service interworking connections.
This attribute is used to define the translation profile
to use when a FR to CR SPVC is configured for Translated
Service Interworking (using the attribute
nncFrSpvcTmPtclMapping). If the profile selected
isn't defined on the remote node then the connection
will be rejected.
Range: 1 = 16.rw INTEGER .1.3.6.1.4.1.123.3.82.1.6.1.13 |
nncFrSpvcDstCfgTmRemapDlciThe source end-point Data Link Connection Identifier
for many-to-one Network Interworking (IWF2) connections.rw INTEGER .1.3.6.1.4.1.123.3.82.1.6.1.14 |
nncFrSpvcDstCfgBillingFlagBilling Configuration for the destination endpoint.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.15 |
nncFrSpvcDstCfgFrPriorityFrame Relay Priority.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.16 |
nncFrSpvcDstCfgLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. It can be configured for either the UNI
side or the NNI side, or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.6.1.17 |
nncFrSpvcDstCfgRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.6.1.18 |
nncCeSpvcTablenncCeSpvcTable contains all the objects sent to a source
endpoint that are used to create, modify, delete
and query CE SPVCCs. The table is indexed using ifIndex,
which includes the circuit number field. SEQUENCE OF NncCeSpvcTableEntry .1.3.6.1.4.1.123.3.82.1.7 |
nncCeSpvcTableEntryAn entry of nncCeSpvcTable. NncCeSpvcTableEntry .1.3.6.1.4.1.123.3.82.1.7.1 |
nncCeSpvcTargEpAddrThis object is used to specify the AESA address of the
target endpoint. The mapping scheme is as follows:
Byte\Bit 8 7 6 5 4 3 2 1
1-13 byte | 13-byte Internal Subscriber Prefix |
14th byte | I/G | U/L | OUI(most significant 6 bits) |
15th byte | OUI(2nd most significant 8 bits |
16th byte | OUI(3rd most significant 8 bits |
17th byte | Shelf/Slot(1st most significant 8 bits |
18th byte | Shelf/Slot(2nd most significant 8 bits |
19th byte |Flag0| Port |
20th byte | Not used, default 0 |rw AtmFormatDisplay .1.3.6.1.4.1.123.3.82.1.7.1.1 |
nncCeSpvcTargVpiThis object contains the virtual path identifier (VPI) value for the
target endpoint. Used in interworking CE to CR connections when
nncCeSpvcTargEpType configured as cellRelay(1). Range: 0 - 4095rw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.2 |
nncCeSpvcTargVciThis object contains the virtual channel identifier (VCI) value for the
target endpoint. Used in interworking CE to CR connections when
nncCeSpvcTargEpType configured as cellRelay(1). Range: 1 - 65535rw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.3 |
nncCeSpvcTargCeNumberThis object contains circuit number, channel group number or
both for the Circuit Emulation endpoint. Used in CE to CE connections
when nncCrSpvccTargEpType is configured as circuitEmulation(3).
For CE connections on unchannelized DS3_CCE card, it's the circuit number
1-28 for UDT circuit number
For CE connections on unchannelized E3_CCE card, it's the circuit number
1-16 for UDT circuit number
For CE connections on E1/T1 CES, it's channel group number.
0 for UDT mode, both T1 and E1
1-31 for E1 in SDT mode
1-24 for T1 in SDT mode
For CE connections on channelized DS3_CCE-2 card, it's circuit number
and channel group number combined in the upper and lower byte.
circuitNum (bits 9-16, = 1 to 28 for channelized DS3,
= 0 for unstructured DS3)
channelGroupNum (bits 1-8, = 1 to 24 for SDT mode,
= 0 for UDT Mode)
For CE connections on channelized E3_CCE-2, it's circuit number and
channel group number combined in the upper and lower byte.
circuitNum (bits 9-16, = 1 to 16)
channelGroupNum (bits 1-8, = 1 to 31 for SDT mode,
= 0 for UDT Mode)
Example: Circuit Number = 7, Channel Group = 3 :
nncCrSpvccTargCeNumber = (Circuit Number * 256) +
Channel Group
= 1795
SPVCs across service types other than circuit emulation do not require
this object.rw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.4 |
nncCeSpvcTargEpTypeThis object specifies a target endpoint
as one of the following types:
cellRelay (1)
circuitEmulation (3)rw Enumeration .1.3.6.1.4.1.123.3.82.1.7.1.5 |
nncCeSpvcAdminStatusThis object accepts two values, enabled (1), and disabled (2).
When the value is disabled, the SPVC is not connected. When
enabled, the SPVC is connected when possible.
Use nncCeSpvcAdminStatus to determine if the connection is
successful.rw Enumeration .1.3.6.1.4.1.123.3.82.1.7.1.6 |
nncCeSpvcPriorityThis object is used to set the priority for a SPVC connection
request. It ranges between 1-16, with the following values:
Best Priority = 1
Default Priority = 3
Worst Priority = 16rw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.7 |
nncCeSpvcMaxAdminWeightThis object is used to set a cost threshold for an SPVC connection.
If the total cost of all VPCs exceeds this weight value for a given
path, this SPVC will choose an alternative path or give up.
Infinite = -1
Min Admin Weight = 0
Max Admin Weight = 2147483647rw Integer32 (-1..2147483647) .1.3.6.1.4.1.123.3.82.1.7.1.8 |
nncCeSpvcOperationThis object is used to request a reroute operation. Querying this
object will not provide any useful information.rw Enumeration .1.3.6.1.4.1.123.3.82.1.7.1.9 |
nncCeSpvcCallStatusThis read-only object is used to query the state of a particular SPVC.
SPVCs that are connected and operational will return a value of
'connected', while those that are incomplete or otherwise unable to be
connected will return 'waitingForResources'. SPVCs that are configured
but not yet connected will contain a value of 'readyForConnect'.ro Enumeration .1.3.6.1.4.1.123.3.82.1.7.1.10 |
nncCeSpvcLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. For circuit emulation UNI side is not
supported. It can be configured for either NNI side or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.7.1.11 |
nncCeSpvcFwdTmBucketOneRateThis object is for peak cell rate (PCR), the
cell rate which the source may never exceed. It is used
to determine which cells are 'excess'.
Measured in Kb/s.
Range: 0 - 2488320 Kb/s
For N x DS0 SDT Basic connections
= ((((1 + 1.0 / 128) * 8 * N / K) + (1.0/1000)) * 53.0 * 8.0) where
N = 1..24 for T1
N = 1..31 for E1
K = 1..47 is the number of data octets per cell.
For N x DS0 SDT CAS connections
= ((((1 + 1.0 / 128) * 8 * (((Cn * N) + (N % 2)) / (Ck * K))) +
(1.0/1000)) * 53.0 * 8.0) where
N = 1..24 for T1
N = 1..31 for E1
K = 2..47 is the number of data octets per cell.
Cn = 49 for T1
Cn = 33 for E1
Ck = 48 for T1
Ck = 32 for E1
= 1755 Kb/s for T1,DS1 UDT connections
= 2328 Kb/s for E1 UDT connections
= 50842 Kb/s for DS3 UDT connectionsrw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.12 |
nncCeSpvcFwdTmBucketOneCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.13 |
nncCeSpvcBwdTmBucketOneRateThis object is for peak cell rate (PCR), the
cell rate which the source may never exceed. It is used
to determine which cells are 'excess'.
Measured in Kb/s.
Range: 0 - 2488320 Kb/s
For N x DS0 SDT Basic connections
= ((((1 + 1.0 / 128) * 8 * N / K) + (1.0/1000)) * 53.0 * 8.0) where
N = 1..24 for T1
N = 1..31 for E1
K = 1..47 is the number of data octets per cell.
For N x DS0 SDT CAS connections
= ((((1 + 1.0 / 128) * 8 * (((Cn * N) + (N % 2)) / (Ck * K))) +
(1.0/1000)) * 53.0 * 8.0) where
N = 1..24 for T1
N = 1..31 for E1
K = 2..47 is the number of data octets per cell.
Cn = 49 for T1
Cn = 33 for E1
Ck = 48 for T1
Ck = 32 for E1
= 1755 Kb/s for T1,DS1 UDT connections
= 2328 Kb/s for E1 UDT connections
= 50842 Kb/s for DS3 UDT connectionsrw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.14 |
nncCeSpvcBwdTmBucketOneCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.7.1.15 |
nncCeSpvcCreatorThe object retrieves the creator of a SPVC connection.ro Enumeration .1.3.6.1.4.1.123.3.82.1.7.1.16 |
nncCeSpvcRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.7.1.17 |
nncCeSpvcDstCfgTablethe nncCeSpvcDstCfg table contains common objects used to
configure, delete, modify and query the destination end
point of an SPVC across different Alcatel CID platforms. SEQUENCE OF NncCeSpvcDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.8 |
nncCeSpvcDstCfgTableEntryAn entry of nncCeSpvcDstCfgTable. NncCeSpvcDstCfgTableEntry .1.3.6.1.4.1.123.3.82.1.8.1 |
nncCeSpvcDstCfgCdvtThis object is used to set cell delay variation tolerance (CDVT) for
one endpoint, measured in microseconds.
Range: 1 - 190,000 microsecondsrw INTEGER .1.3.6.1.4.1.123.3.82.1.8.1.1 |
nncCeSpvcDstCfgLocRerouteConfigThis object is used to configure the 'reroute on loss of continuity'
feature using OAM-CC cells. For circuit emulation UNI side is not
supported. It can be configured for either NNI side or disabled.rw Enumeration .1.3.6.1.4.1.123.3.82.1.8.1.2 |
nncCeSpvcDstCfgRowStatusThis object is used to control the status of a PDU and to query
the status of an SPVC. When the RowStatus value is 'createAndWait',
information for a row is cached in memory; when RowStatus is set to
'createAndGo' or 'active', it indicates that all information is to be
written to permanent storage, and the SPVC to be enabled (AdminStatus
must also be set to 'enabled'). When querying the object, 'active'
indicates a configured SPVC with its AdminStatus enabled, while a status
of 'notInService' indicates either a disabled AdminStatus or an
inability to connect the SPVC. If a query returns 'notInService', use
the CallStatus object to further determine the state of the SPVC. If
the value 'notReady' is returned, it indicates that the SNMP agent is
awaiting further information before activating the connection.
When deleting a connection, use this object with the value 'destroy'rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.123.3.82.1.8.1.3 |
nncExtSpvcGroups OBJECT IDENTIFIER .1.3.6.1.4.1.123.3.82.3 |
nncExtSpvcCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.123.3.82.4 |