NETI-TRUNK-MIB
MIB for DTM network links (trunks). DTM trunks provide transport of DTM data between two DTM networks nodes. The MIB currently includes the DPP-IP group (neti-dppip), providing management of DPP-IP encapsulated DTM over IP/Ethernet. It includes configuration information and status.
Main OID:
netiTrunkMIB.1.3.6.1.4.1.2928.2.3
84
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
84 total| Object Name |
|---|
netiTrunkMIBMIB for DTM network links (trunks). DTM trunks provide transport of DTM data between two DTM networks nodes. The MIB currently includes the DPP-IP group (neti-dppip), providing management of DPP-IP encapsulated DTM over IP/Ethernet. It includes configuration information and status. MODULE-IDENTITY .1.3.6.1.4.1.2928.2.3 |
trunkObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2928.2.3.1 |
dppipGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2928.2.3.1.1 |
dppipNumberThe number of DPP-IP interfaces (regardless of their current state) present on this system.ro Integer32 .1.3.6.1.4.1.2928.2.3.1.1.1 |
dppipLastChangeThe value of sysUpTime when status or configuration of any the objects in the dppipTable was last changed.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.2928.2.3.1.1.2 |
dppipTableA list of DPP-IP interface entries. The number of entries is given by the value of dppipNumber. The following objects need to be written simultaneously, i.e. as a single write operation, while dppipAdminStatus is `up': dppipTxSlots, dppipMtu, dppipTxFecMode, dppipTxFecRows, dppipTxFecCols SEQUENCE OF DppipEntry .1.3.6.1.4.1.2928.2.3.1.1.3 |
dppipEntryA DPP-IP interface entry containing objects at the subnetwork layer and below for a particular interface. DppipEntry .1.3.6.1.4.1.2928.2.3.1.1.3.1 |
dppipIndexA value greater than zero that is unique for each DPP-IP interface. The value for each DPP-IP interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.1 |
dppipNameThe textual name of the interface. The value of this object should be the name of the DPP-IP interface as assigned by the local device.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2928.2.3.1.1.3.1.2 |
dppipAddressThe IPv4 address of the DPP-IP interface.rw IpAddress .1.3.6.1.4.1.2928.2.3.1.1.3.1.3 |
dppipNetMaskThe subnet mask associated with the IP address of DPP-IP interface. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.rw IpAddress .1.3.6.1.4.1.2928.2.3.1.1.3.1.4 |
dppipDefaultGatewayThe IPv4 address of the default gateway. Packets addressed to a destination outside the subnet of the DPP-IP interface are by default routed to this gateway.rw IpAddress .1.3.6.1.4.1.2928.2.3.1.1.3.1.5 |
dppipPeerAddressThe IPv4 address of the peer DPP-IP interface at the remote end of the DTM trunk.rw IpAddress .1.3.6.1.4.1.2928.2.3.1.1.3.1.6 |
dppipTxSlotsThe DPP-IP interface's current transmit side capacity in slots per DTM frame.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.7 |
dppipTxUsedCapacityAn estimate of the transmit side physical layer capacity used by the DPP-IP interface in bits per second. It represents a minimum required capacity along the network path.ro Gauge32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.8 |
dppipRxSlotsThe DPP-IP interface's current receive side capacity in slots per DTM frame.ro Gauge32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.9 |
dppipRxUsedCapacityAn estimate of the receive side physical layer capacity used by the DPP-IP interface in bits per second. It represents a minimum required capacity along the network path.ro Gauge32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.10 |
dppipDelayVariationThe RMS (i.e. standard deviation) value of the DPP-IP path delay variation in ns. This value represents a momentary snapshot of the delay variation.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.11 |
dppipOperStatusThe current operational state of the interface. The testing(3) state indicates that no operational frames can be passed.ro Enumeration .1.3.6.1.4.1.2928.2.3.1.1.3.1.12 |
dppipFailureA textual string describing a fault status on the DPP-IP interface. The object presents an empty string if there are no faults on the interface.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2928.2.3.1.1.3.1.13 |
dppipReceivedFramesThe total number of DPP-IP frames that have been received.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.14 |
dppipMissingFramesThe number of DPP-IP frames that were missing in the frame sequence, i.e. the expected sequence numbers were not found in the DPP-IP framing buffer.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.15 |
dppipDeliveredFramesThe total number of DPP-IP data frames that have been delivered to the DTM interface.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.16 |
dppipDroppedFramesThe number of DPP-IP frames that have been received and have not been processed since the interface was unable to align them to the DPP-IP frame sequence.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.17 |
dppipDuplicateFramesThe number of DPP-IP frames that were received with a sequence number of an already processed DPP-IP frame.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.18 |
dppipReorderedFramesThe number of DPP-IP frames that were received out of order, but could still be aligned to the DPP-IP frame sequence.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.19 |
dppipLostFramesThe number of missing DPP-IP data frames that could not be delivered to the DTM interface.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.20 |
dppipRecoveredFramesThe number of missing DPP-IP data frames that were recovered by the FEC procedure.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.21 |
dppipSentFramesThe total number of DPP-IP frames that have been sent.ro Counter64 .1.3.6.1.4.1.2928.2.3.1.1.3.1.22 |
dppipDelayVarPtpThe point-to-point value of the DPP-IP path delay variation in nanoseconds. The special value 0 means that the measurement is incompletero Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.23 |
dppipDelayVar999The 99.9 percentile value of the DPP-IP path delay variation given in nanoseconds. The special value 0 means that the measurement is incomplete.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.24 |
dppipAdminStatusThe desired state of the interface.rw Enumeration .1.3.6.1.4.1.2928.2.3.1.1.3.1.25 |
dppipVlanThe VLAN identity associated to the DPP-IP interface. The value 0 indicates that the DPP-IP interface does not belong to a VLAN. The value -1 indicates that Ethernet frames from the DPP-IP interface are not tagged.rw Integer32(-1..4095) .1.3.6.1.4.1.2928.2.3.1.1.3.1.26 |
dppipDelayVar01The 0.1 percentile value of the DPP-IP path delay variation given in nanoseconds. The special value 0 means that the measurement is incomplete.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.27 |
dppipPrioThe Ethernet priority for frames sent from the DPP-IP interface. Ignored if frames are untagged (i.e. dppipVlan is -1).rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.28 |
dppipPhysIfA reference to an object representing the physical interface that supports the DPP-IP interface. The special value .0.0 is used, when no such reference is available.ro RowPointer (SNMPv2-TC) .1.3.6.1.4.1.2928.2.3.1.1.3.1.29 |
dppipMtuThe Maximum Transmission Unit of the DPP-IP interface, i.e. the maximum size of the DPP-IP payload, including IP header, UDP header and DPP-IP header.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.30 |
dppipTtlThe Time To Live of frames sent at the DPP-IP interface. This value is set in the IP header.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.31 |
dppipDscpThe Differential Services Coding Point of frames sent at the DPP-IP interface. This value is set in the IP header.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.32 |
dppipRxSlotsPerFrameNumber of DTM slots per received DPP-IP data frame.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.33 |
dppipAvailTxSlotsThe maximum transmit slot rate (slots/frame) that can be allocated at the DTM switch.ro Gauge32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.34 |
dppipAvailRxSlotsThe maximum receive slot rate (slots/frame) that can be allocated at the DTM switch.ro Gauge32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.35 |
dppipMinUsageRatioThe minimum allowed usage ratio (used slots/configured slots) in per-mille, when dynamic trunk functionality is used. 1000 is default and indicates that the Dynamic Trunk function is disabled. Requires Dynamic Trunk function support equal to 1.1 or higher.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.36 |
dppipTxTranspSlotsThe DPP-IP interface's current transmit side capacity in slots per DTM frame that is actually transported over the. When Dynamic Trunk functionality is disabled this is equal to dppipTxSlots. When Dynamic Trunk functionality is enabled this is less or equal to dppipTxSlots, since slots that are not used by any channel need not be transported. Requires Dynamic Trunk function support equal to 1.1 or higher.ro Gauge32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.37 |
dppipRxTranspSlotsThe DPP-IP interface's current receive side capacity in slots per DTM frame that is actually transported. When Dynamic Trunk functionality is disabled this is equal to dppipRxSlots. When Dynamic Trunk functionality is enabled this is less or equal to dppipRxSlots, since slots that are not used by any channel need not be transported. Requires Dynamic Trunk function support equal to 1.1 or higher.ro Gauge32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.38 |
dppipNomDTDelayThe nominal extra delay in ns when the Dynamic Trunk function is enabled. Requires Dynamic Trunk function support equal to 1.1 or higher.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.39 |
dppipTxFecModeThe DPP-IP interface's current mode of operation of the transmit side Forward Error Correction function (FEC). The FEC function may be not used (fecNone), used for column correction (fec1D) or used for both row and column correction (fec2D).rw FecMode .1.3.6.1.4.1.2928.2.3.1.1.3.1.40 |
dppipTxFecRowsThe DPP-IP interface's current number of data rows in the transmit side Forward Error Correction (FEC) matrix. This object is not applicable when dppipTxFecMode is fecNone.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.41 |
dppipTxFecColsThe DPP-IP interface's current number of data columns in the transmit side Forward Error Correction (FEC) matrix. This object is not applicable when dppipTxFecMode is fecNone.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.42 |
dppipRxFecModeThe DPP-IP interface's current mode of operation of the receive side Forward Error Correction function (FEC). The FEC function may be not used (fecNone), used for column correction (fec1D) or used for both row and column correction (fec2D).ro FecMode .1.3.6.1.4.1.2928.2.3.1.1.3.1.43 |
dppipRxFecRowsThe DPP-IP interface's current number of data rows in the receive side Forward Error Correction (FEC) matrix. This object is not applicable when dppipRxFecMode is fecNone.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.44 |
dppipRxFecColsThe DPP-IP interface's current number of data columns in the receive side Forward Error Correction (FEC) matrix. This object is not applicable when dppipRxFecMode is fecNone.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.45 |
dppipCntControlControls the statistics counter monitoring. The statistics monitoring is restarted and all counters set to 0, by writing `reset' to this object.rw Enumeration .1.3.6.1.4.1.2928.2.3.1.1.3.1.46 |
dppipSuppressAlarmsSuppression control for alarms from the DPP-IP interface. When set to `true', all alarms are suppressed.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2928.2.3.1.1.3.1.47 |
dppipSigFailFilterSignal fail filter hold-off time in milliseconds. Trail Signal Fail conditions must be persistent during the hold-off time, before operStatus is changed from `up' to `down'.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.48 |
dppipDegThresholdThe detection threshold for DEG alarm. A bad second is declared when the number of errored blocks is equal to or greater than the threshold, otherwise a good second is declared. Default is 1200rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.49 |
dppipDegPeriodThe persistence time for detection of DEG alarm as the number of consecutive seconds with changed status (bad or good) before the alarm is set or cleared.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.50 |
dppipTolJitterThe tolerated jitter and wander of the DPP-IP interface given in microseconds.rw Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.3.1.51 |
dppipLimitsTableA list of DPP-IP interface limits entries. The number of entries is given by the value of dppipNumber. SEQUENCE OF DppipLimitsEntry .1.3.6.1.4.1.2928.2.3.1.1.4 |
dppipLimitsEntryA DPP-IP interface limits entry containing limits for a particular interface. DppipLimitsEntry .1.3.6.1.4.1.2928.2.3.1.1.4.1 |
dppipMaxFecModeThe DPP-IP interface's maximum mode of operation of the Forward Error Correction function (FEC). The FEC function may be not used (fecNone), used for column correction (fec1D) or used for both row and column correction (fec2D).ro FecMode .1.3.6.1.4.1.2928.2.3.1.1.4.1.1 |
dppipMaxFecRowsThe DPP-IP interface's maximum number of data rows in the transmit side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.2 |
dppipMinFecRowsThe DPP-IP interface's minimum number of data rows in the transmit side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.3 |
dppipMaxFecColsThe DPP-IP interface's maximum number of data columns in the transmit side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.4 |
dppipMinFecColsThe DPP-IP interface's minimum number of data columns in the transmit side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.5 |
dppipMaxFecElemsThe DPP-IP interface's maximum number of data elements in the transmit side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.6 |
dppipMaxTxSlotsThe maximum number of slots per DTM frame that can be allocated at the DPP-IP transmit interface.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.7 |
dppipMinTxSlotsThe minimum number of slots per DTM frame that can be allocated at the DPP-IP transmit interface.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.8 |
dppipMaxTolJitterThe maximum tolerated jitter that can be configured expressed in units of DPP-IP inter-frame intervals. The DPP-IP inter-frame interval in microseconds is: dppipRxSlotsPerFrame * 125 / dppipRxSlots.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.9 |
dppipMinTolJitterThe minimum tolerated jitter that can be configured expressed in units of DPP-IP inter-frame intervals. The DPP-IP inter-frame interval in microseconds is: dppipRxSlotsPerFrame * 125 / dppipRxSlots.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.4.1.10 |
dppipDTSupportThe local interface's maximum level of support for the Dynamic Trunk function.ro DppipSupport .1.3.6.1.4.1.2928.2.3.1.1.4.1.11 |
dppipTTSupportThe local interface's maximum level of support for the Time Transfer function.ro DppipSupport .1.3.6.1.4.1.2928.2.3.1.1.4.1.12 |
dppipPeerLimitsTableA list of DPP-IP interface limits entries. The number of entries is given by the value of dppipNumber. SEQUENCE OF DppipPeerLimitsEntry .1.3.6.1.4.1.2928.2.3.1.1.5 |
dppipPeerLimitsEntryA DPP-IP interface peer limits entry containing limits for the peer of a particular interface. DppipPeerLimitsEntry .1.3.6.1.4.1.2928.2.3.1.1.5.1 |
dppipPeerMaxFecModeThe peer interface's maximum mode of operation of the Forward Error Correction function (FEC). The FEC function may be not used (fecNone), used for column correction (fec1D) or used for both row and column correction (fec2D).ro FecMode .1.3.6.1.4.1.2928.2.3.1.1.5.1.1 |
dppipPeerMaxFecRowsThe peer interface's maximum number of data rows in the receive side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.5.1.2 |
dppipPeerMinFecRowsThe peer interface's minimum number of data rows in the receive side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.5.1.3 |
dppipPeerMaxFecColsThe peer interface's maximum number of data columns in the receive side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.5.1.4 |
dppipPeerMinFecColsThe peer interface's minimum number of data columns in the receive side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.5.1.5 |
dppipPeerMaxFecElemsThe peer interface's maximum number of data elements in the receive side Forward Error Correction (FEC) matrix.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.5.1.6 |
dppipPeerMaxRxSlotsThe maximum number of slots per DTM frame that can be allocated at the receive interface in the peer.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.5.1.7 |
dppipPeerMinRxSlotsThe minimum number of slots per DTM frame that can be allocated at the DPP-IP receive interface of the peer.ro Unsigned32 .1.3.6.1.4.1.2928.2.3.1.1.5.1.8 |
dppipPeerDTSupportThe peer interface's maximum level of support for the Dynamic Trunk function.ro DppipSupport .1.3.6.1.4.1.2928.2.3.1.1.5.1.9 |
dppipPeerTTSupportThe peer interface's maximum level of support for the Time Transfer function.ro DppipSupport .1.3.6.1.4.1.2928.2.3.1.1.5.1.10 |