Home/Catalog/NETI-VAS-MIB

NETI-VAS-MIB

AI MIB Summary

The NETI-VAS-MIB manages and monitors video appliance services by configuring encoder and decoder pipelines alongside physical ASI/SDI interfaces to control reliable UDP-based push and pull video transport streams. It provides granular visibility into stream processing states, including source/sink topology, transport initiation modes, and associated performance statistics for IP network video delivery.

This document is work in progress, and it is likely to change. Reference: NID4613. MIB for Video Appliance Services. The MIB describes objects for setting up and monitoring of reliable video transports over an IP network. It also contains configuration objects for encoders and decoders. The MIB contains conceptual tables that describes the different objects: The table vasIfTable contains physical video ports, such as ASI or SDI ports. The table vasEncPipeTable contains video encoder pipelines. A video encoder pipeline can encode the video (e.g. from SDI to MPEG-4) to a stream, and process the audio, video and meta-data. The table vasDecPipeTable contains video decoder pipelines. A video decoder pipeline can decode a stream (from e.g. MPEG-4 to SDI) and process the audio, video and data in the stream. The table vasUdpSnkTable contains objects that receives an UDP video stream on an IP interface and provides it as an input to another source object. The table vasUdpSrcTable contains objects that takes a video stream from a sink object and transmits it as a UDP stream from an IP interface. This object is the complement to an object in the vasUdpSnkTable. The table vasPulSrcTable contains the source objects of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source (sender) to the sink (receiver) at the sink. The table vasMpuSrcTable contains the source objects of pull transports, where multiple transports to different destinations may be setup from the same source. The table vasPulSnkTable contains the sink part of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source (sender) to the sink (receiver) at the sink. The table vasPusSrcTable contains the source part of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source (sender) to the sink (receiver) at the source. The table vasPusSnkTable contains the sink part of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source (sender) to the sink (receiver) at the source. The MIB also contains tables for statistics.
Main OID:
netiVasMIB.1.3.6.1.4.1.2928.2.5
265
Objects
Active
Status
4
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
SNMP-FRAMEWORK-MIB
INET-ADDRESS-MIB

Objects

265 total
Object Name
netinsight
OBJECT IDENTIFIER
.1.3.6.1.4.1.2928
netiGeneric
OBJECT IDENTIFIER
.1.3.6.1.4.1.2928.2
netiVasMIBThis document is work in progress, and it is likely to change. Reference: NID4613. MIB for Video Appliance Services. The MIB describes objects for setting up and monitoring of reliable video transports over an IP network. It also contains configuration objects for encoders and decoders. The MIB contains conceptual tables that describes the different objects: The table vasIfTable contains physical video ports, such as ASI or SDI ports. The table vasEncPipeTable contains video encoder pipelines. A video encoder pipeline can encode the video (e.g. from SDI to MPEG-4) to a stream, and process the audio, video and meta-data. The table vasDecPipeTable contains video decoder pipelines. A video decoder pipeline can decode a stream (from e.g. MPEG-4 to SDI) and process the audio, video and data in the stream. The table vasUdpSnkTable contains objects that receives an UDP video stream on an IP interface and provides it as an input to another source object. The table vasUdpSrcTable contains objects that takes a video stream from a sink object and transmits it as a UDP stream from an IP interface. This object is the complement to an object in the vasUdpSnkTable. The table vasPulSrcTable contains the source objects of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source (sender) to the sink (receiver) at the sink. The table vasMpuSrcTable contains the source objects of pull transports, where multiple transports to different destinations may be setup from the same source. The table vasPulSnkTable contains the sink part of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source (sender) to the sink (receiver) at the sink. The table vasPusSrcTable contains the source part of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source (sender) to the sink (receiver) at the source. The table vasPusSnkTable contains the sink part of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source (sender) to the sink (receiver) at the source. The MIB also contains tables for statistics.
MODULE-IDENTITY
.1.3.6.1.4.1.2928.2.5
vasInterfaceGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.2928.2.5.1
vasIfTableTable conceptual table contains video interfaces; physical video ports, such as ASI and SDI ports.
SEQUENCE OF VasIfEntry
.1.3.6.1.4.1.2928.2.5.1.1
vasIfEntryAn entry in the conceptual table represents one video interface.
VasIfEntry
.1.3.6.1.4.1.2928.2.5.1.1.1
vasIfIndexAn index that uniquely identifies the interface in the table. The index is maintained across reboots of the node. The index is generally a small number.
Unsigned32
.1.3.6.1.4.1.2928.2.5.1.1.1.1
vasIfNameA textual name of the interface. The name is unique within the node. The first part of the name is a string representing the type of interface, the second part of the name contains the device number followed by the port number within the device, separated by a semi-colon.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.1.1.1.2
vasIfPurposeA text that can describe the purpose of the interface. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.1.1.1.3
vasIfAdminStatusThe administrative state of the interface. The value controls the desired state of the interface. up(1). The interface shall be enabled. down(2). The interface shall be disabled.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.1.1.1.4
vasIfOperStatusThe operational state of the interface. The value normally follow the state of the administrative state. up(1). The interface is up and operational. down(2). The interface is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasIfFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.1.1.1.5
vasIfFailureA text describing the configuration or error status of the interface. The text is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.1.1.1.6
vasIfLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.1.1.1.7
vasIfResetStatisticsResets all statistics counters for the interface. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.1.1.1.8
vasIfInputFromIf the interface is an output interface, as set on vasIfPortMode, then this is a reference to the object that shall deliver the video stream to the interface. Which type of object that is a valid input depends on the type of interface. If the interface is an input interface, as set on the vasIfPortMode, then the value is always `.0.0'.rw
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.1.1.1.9
vasIfPortModeSpecifies how the interface shall operate. When the port is set as an input, then a video stream received on the physical port is distributed to the objects having this port as their input. When the port is set as an output, then a video stream received from the object referenced in vasIfInputFrom is transmitted on the physical port. asiInput(1). The port shall operate as an ASI input. asiOutput(2). The port shall operate as an ASI output. sdiInput(3). The port shall operate as an SDI input. sdiOutput(4). The port shall operate as an SDI output.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.1.1.1.10
vasIfActiveFormatThe video source format.ro
VasVideoFormat
.1.3.6.1.4.1.2928.2.5.1.1.1.11
vasEncoderPipeGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.2928.2.5.2
vasEncPipeTableThe conceptual table contains objects that represent video encoder pipelines. A video encoder pipeline can encode the video (e.g. from SDI to MPEG-4) to a stream, and process the audio, video and meta-data.
SEQUENCE OF VasEncPipeEntry
.1.3.6.1.4.1.2928.2.5.2.1
vasEncPipeEntryAn entry in the conceptual table represents one encoder pipeline.
VasEncPipeEntry
.1.3.6.1.4.1.2928.2.5.2.1.1
vasEncPipeIndexAn index that uniquely identifies the encoder pipeline in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.2.1.1.1
vasEncPipeRowStatusSee SNMPv2-TC. Use vasEncPipeAdminStatus to activate and de-activate an encoder pipeline. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new encoder pipeline. To activate the encoder pipeline, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The encoder pipeline is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.2.1.1.2
vasEncPipeNameA textual name of the encoder pipeline. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.2.1.1.3
vasEncPipePurposeA text that can describe the purpose of the encoder pipeline. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.2.1.1.4
vasEncPipeAdminStatusThe administrative state of the encoder pipeline. up(1). The encoder pipeline shall be enabled and allocates the necessary resources. down(2). The encoder pipeline shall be disabled and will not allocate any resources.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.2.1.1.5
vasEncPipeOperStatusThe operational state of the encoder pipe. The value normally follow the state of the administrative state. up(1). The encoder pipe is up and operational. down(2). The encoder pipe is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasEncPipeFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.2.1.1.6
vasEncPipeFailureA text describing the configuration or error status of the encoder pipeline. The text is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.2.1.1.7
vasEncPipeLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.2.1.1.8
vasEncPipeResetStatisticsResets all statistics counters for the encoder pipe. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.2.1.1.9
vasEncPipeStatsTr101Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.2.1.1.10
vasEncPipeEnableTr101Enables or disables the ETSI TR 101 290 statistics collection.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.2.1.1.11
vasEncPipeInputFromA reference to the object that shall supply the video stream to the encoder pipe. This could be a physical input port in the vasIfTable, or a stream from e.g. a decoder pipe in the vasDecPipeTable. The value `.0.0' is used when no input is specified.rw
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.2.1.1.12
vasEncPipeCipherA cipher to be used when encrypting the transport stream generated by the encoder pipeline.rw
VasCipher
.1.3.6.1.4.1.2928.2.5.2.1.1.13
vasEncPipeEncryptKeyThe key to be used when encrypting the transport stream generated by the encoder pipeline. The key shall be provided as a text with hexadecimal digits presented as lower case characters.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.2.1.1.14
vasEncPipeProcessedFramesRunning counter of number of encoded frames.ro
Counter32
.1.3.6.1.4.1.2928.2.5.2.1.1.15
vasEncPipeCurrentTsBitrateCurrent transport stream bitrate in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.2.1.1.16
vasEncPipeVideoBitrateTarget video bitrate after encoding in kbps.rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.2.1.1.17
vasDecoderPipeGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.2928.2.5.3
vasDecPipeTableThe conceptual table contains objects that represent video decoder pipelines. A video decoder pipeline can decode a stream (from e.g. MPEG-4 to SDI) and process the audio, video and data in the stream.
SEQUENCE OF VasDecPipeEntry
.1.3.6.1.4.1.2928.2.5.3.1
vasDecPipeEntryAn entry in the conceptual table represents one decoder pipeline.
VasDecPipeEntry
.1.3.6.1.4.1.2928.2.5.3.1.1
vasDecPipeIndexAn index that uniquely identifies the decoder pipeline in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.3.1.1.1
vasDecPipeRowStatusSee SNMPv2-TC. Use vasDecPipeAdminStatus to activate and de-activate a decoder pipeline. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new decoder pipeline. To activate the decoder pipeline, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The decoder pipeline is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.3.1.1.2
vasDecPipeNameA textual name of the decoder pipeline. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.3.1.1.3
vasDecPipePurposeA text that can describe the purpose of the decoder pipeline. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.3.1.1.4
vasDecPipeAdminStatusThe administrative state of the decoder pipeline. up(1). The decoder pipeline shall be enabled and will allocate the necessary resources. down(2). The decoder pipeline shall be disabled and will not allocate any resources.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.3.1.1.5
vasDecPipeOperStatusThe operational state of the decoder pipe. The value normally follow the state of the administrative state. up(1). The decoder pipe is up and operational. down(2). The decoder pipe is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasDecPipeFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.3.1.1.6
vasDecPipeFailureA text describing the configuration or error status of the decoder pipeline. The text is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.3.1.1.7
vasDecPipeLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.3.1.1.8
vasDecPipeResetStatisticsResets all statistics counters for the decoder pipe. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.3.1.1.9
vasDecPipeInputFromA reference to the object that shall supply the encoded video stream to the decoder pipe. This could be e.g. a pull or push transport sink in the vasPulSnkTable or vasPusSnkTable, or an encoder pipe in the vasEncPipeTable. The value `.0.0' is used when no input is specified.rw
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.3.1.1.10
vasDecPipeCipherA cipher to be used when decrypting the transport stream.rw
VasCipher
.1.3.6.1.4.1.2928.2.5.3.1.1.11
vasDecPipeDecryptKeyThe key to be used when decrypting the transport stream. The key shall be provided as a text with hexadecimal digits presented as lower case characters.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.3.1.1.12
vasDecPipeProcessedFramesRunning counter of number of decoded frames.ro
Counter32
.1.3.6.1.4.1.2928.2.5.3.1.1.13
vasDecPipeCurrentTsBitrateCurrent transport stream bitrate in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.3.1.1.14
vasDecPipeVideoBitrateVideo bitrate after decoding in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.3.1.1.15
vasTransportsGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.2928.2.5.4
vasStreamPortThe UDP port number that is used when listening at stream connections requests.rw
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.1
vasUdpSrcTableThe conceptual table contains objects that takes a video stream from a sink object and transmits it as a UDP stream from an IP interface. This object is the complement to an object in the vasUdpSnkTable.
SEQUENCE OF VasUdpSrcEntry
.1.3.6.1.4.1.2928.2.5.4.2
vasUdpSrcEntryAn entry in the conceptual table represents one UDP source.
VasUdpSrcEntry
.1.3.6.1.4.1.2928.2.5.4.2.1
vasUdpSrcIndexAn index that uniquely identifies the UDP source in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.2.1.1
vasUdpSrcRowStatusSee SNMPv2-TC. Use vasUdpSrcAdminStatus to activate and de-activate a UDP source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new UDP source. To activate the UDP source, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The UDP source is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.2.1.2
vasUdpSrcNameA textual name of the UDP source. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.3
vasUdpSrcPurposeA text that can describe the purpose of the UDP source. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.4
vasUdpSrcAdminStatusThe administrative state of the UDP source. up(1). The UDP source shall be enabled and allocates the necessary resources. down(2). The UDP source shall be disabled and will not allocate any resources.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.4.2.1.5
vasUdpSrcOperStatusThe operational state of the UDP source. The value normally follow the state of the administrative state. up(1). The UDP source is up and operational. down(2). The UDP source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasUdpSrcFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.4.2.1.6
vasUdpSrcFailureA string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.7
vasUdpSrcLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.2.1.8
vasUdpSrcConnectionStatusThe status of the stream transport connection.ro
VasConnectionStatus
.1.3.6.1.4.1.2928.2.5.4.2.1.9
vasUdpSrcResetStatisticsResets all statistics counters for the object. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.4.2.1.10
vasUdpSrcStatsUdpIndex for an entry in statistics table vasUdpStatisticsTable for this object.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.2.1.11
vasUdpSrcInputFromA reference to the object that shall supply the video stream to the UDP source. This could be e.g. a pull or push sink in the vasPulSnkTable or vasPusSnkTable, or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.rw
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.2.1.12
vasUdpSrcRemoteHostTypeDescribes how vasUdpSrcRemoteHostAddress shall be interpreted. Supported values are `unknown', `ipv4' and `dns'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.13
vasUdpSrcRemoteHostAddressThe IP address or DNS hostname of the remote source that shall provide the UDP stream.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.14
vasUdpSrcRemotePortThe port number at the remote source that shall provide the UDP stream.rw
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.15
vasUdpSrcLocalIfTypeDescribes how the vasUdpSrcLocalIfAddress shall be interpreted. Supported value is `ipv4'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.16
vasUdpSrcLocalIfAddressThe IP address of a local interface (NIC) that shall be used as input for the video stream. If any interface can be used, set the IPv4 address 0.0.0.0.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.17
vasUdpSrcLocalPortThe local UPD port number. Use 0 for any port.rw
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.18
vasUdpSrcCipherThe cipher to use for encrypting the UDP video stream.rw
VasCipher
.1.3.6.1.4.1.2928.2.5.4.2.1.19
vasUdpSrcDecryptKeyThe key to be used when encrypting the UDP video stream. The key shall be provided as a text with hexadecimal digits presented as lower case characters.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.2.1.20
vasUdpSrcTtlTTL, the Time to Live (hop limit) for the UDP/IP datagram.rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.2.1.21
vasUdpSrcDontFragmentThe Don't Fragment (DF) flag on the IP packet. When set, then if fragmentation would be required to route a packet, the packet is dropped instead.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.2.1.22
vasUdpSnkTableThe conceptual table contains objects that receives a UDP video stream on an IP interface and provides it as an input to another source object.
SEQUENCE OF VasUdpSnkEntry
.1.3.6.1.4.1.2928.2.5.4.3
vasUdpSnkEntryAn entry in the conceptual table represents one UDP sink.
VasUdpSnkEntry
.1.3.6.1.4.1.2928.2.5.4.3.1
vasUdpSnkIndexAn index that uniquely identifies the UDP sink in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.3.1.1
vasUdpSnkRowStatusSee SNMPv2-TC. Use vasUdpSnkAdminStatus to activate and de-activate a UDP source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new UDP sink. To activate the UDP sink, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The UDP sink is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.3.1.2
vasUdpSnkNameA textual name of the UDP sink. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.3
vasUdpSnkPurposeA text that can describe the purpose of the UDP sink. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.4
vasUdpSnkAdminStatusThe administrative state of the UDP sink. up(1). The UDP sink shall be enabled and allocates the necessary resources. down(2). The UDP sink shall be disabled and will not allocate any resources.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.4.3.1.5
vasUdpSnkOperStatusThe operational state of the UDP sink. The value normally follow the state of the administrative state. up(1). The UDP sink is up and operational. down(2). The UDP sink is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasUdpSnkFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.4.3.1.6
vasUdpSnkFailureA string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.7
vasUdpSnkLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.3.1.8
vasUdpSnkConnectionStatusThe status of the stream transport connection.ro
VasConnectionStatus
.1.3.6.1.4.1.2928.2.5.4.3.1.9
vasUdpSnkResetStatisticsResets all statistics counters for the object. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.4.3.1.10
vasUdpSnkStatsUdpIndex for an entry in statistics table vasUdpStatisticsTable for this object.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.3.1.11
vasUdpSnkStatsTr101Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.3.1.12
vasUdpSnkEnableTr101Enables or disables ETSI TR 101 290 statistics collection.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.3.1.13
vasUdpSnkRemoteInetTypeDescribes the format of vasUdpSnkRemoteInetAddress.ro
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.14
vasUdpSnkRemoteInetAddressThe IP address of the remote host from where the UDP stream is being received. The value is empty and vasUdpSnkRemoteInetType is `unknown' when a stream is not received.ro
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.15
vasUdpSnkLocalIfTypeDescribes how the vasUdpSnkLocalIfAddress shall be interpreted. Supported value is `ipv4'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.16
vasUdpSnkLocalIfAddressThe IP address of a local interface (NIC) that shall be used as input for the video stream. If any interface can be used, set the IPv4 address 0.0.0.0.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.17
vasUdpSnkLocalPortThe local UDP port that shall be used for input.rw
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.18
vasUdpSnkCipherThe cipher that shall be used for decrypting the received UDP video stream.rw
VasCipher
.1.3.6.1.4.1.2928.2.5.4.3.1.19
vasUdpSnkEncryptKeyThe key to be used when decrypting the UDP video stream. The key shall be provided as a text with hexadecimal digits presented as lower case characters.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.20
vasUdpSnkMcastIpTypeThe format of vasUdpSnkMcastIp and vasUdpSnkSsmSourceIp. Supported values are `unknown' and `ipv4'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.21
vasUdpSnkMcastIpThe multicast IP address if joining a multicast UDP stream. Set empty and vasUdpSnkMcastIpType to `unknown' if not multicast.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.22
vasUdpSnkSsmSourceIpThe source address if source-specific multicast (SSM) shall be used. Set to empty and vasUdpSnkMcastIpType to `unknown' if multicast shall not be used, or all-zero (0.0.0.0) if multicast but where SSM shall not be used.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.3.1.23
vasUdpSnkCompressRemoves null-packets in an MPEG transport stream.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.3.1.24
vasPulSrcTableThe conceptual table contains objects that represent the source (sender) in a pull transport, i.e. a transport of a stream that is initiated from the sink side, where the stream is pulled from the source to the sink at the sink.
SEQUENCE OF VasPulSrcEntry
.1.3.6.1.4.1.2928.2.5.4.4
vasPulSrcEntryAn entry in the conceptual table represents one pull source object.
VasPulSrcEntry
.1.3.6.1.4.1.2928.2.5.4.4.1
vasPulSrcIndexAn index that uniquely identifies the pull source in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.4.1.1
vasPulSrcRowStatusSee SNMPv2-TC. Use vasPulSrcAdminStatus to activate and de-activate a Pull source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Pull source. To activate the Pull source, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Pull source is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.4.1.2
vasPulSrcNameA textual name of the Pull source. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.3
vasPulSrcPurposeA text that can describe the purpose of the Pull source. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.4
vasPulSrcAdminStatusThe administrative state of the Pull source. The value controls the desired state of the Pull source. up(1). The Pull source shall be enabled. down(2). The Pull source shall be disabled.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.4.4.1.5
vasPulSrcOperStatusThe operational state of the Pull source. The value normally follow the state of the administrative state. up(1). The Pull source is up and operational. down(2). The Pull source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPulSrcFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.4.4.1.6
vasPulSrcFailureA string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.7
vasPulSrcLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.4.1.8
vasPulSrcConnectionStatusThe status of the stream transport connection.ro
VasConnectionStatus
.1.3.6.1.4.1.2928.2.5.4.4.1.9
vasPulSrcResetStatisticsResets all statistics counters for the object. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.4.4.1.10
vasPulSrcStatsTrspIndex for an entry in statistics vasTrspStatisticsTable table for this object.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.4.1.11
vasPulSrcRemoteInetTypeFormat of vasPulSrcRemoteInetAddress.ro
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.12
vasPulSrcRemoteInetAddressThe IP address of the remote host to where the transport stream is being sent. The value is empty and vasPulSrcRemoteInetType is `unknown' when a stream is not sent.ro
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.13
vasPulSrcStreamIdAssigns the stream ID to a transport stream. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.14
vasPulSrcInputFromA reference to the object that shall supply the video stream to the pull source. This could be e.g. an encoder pipeline in the vasEncPipeTable or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.rw
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.4.1.15
vasPulSrcRemoteIdThe remote ID is the assigned to the remote host where the transport stream is received. This is used for compatibility with nodes that does not implement this MIB. A node that implements this MIB is assigned the default value `nimbrava'.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.16
vasPulSrcPasswordA password used for the transport stream. The vasPulSnkPassword on the sink at the remote host must match.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.4.1.17
vasMpuSrcTableThe conceptual table contains objects that represent the source (sender) of pull transports, where multiple transports to different destinations may be setup from the same source.
SEQUENCE OF VasMpuSrcEntry
.1.3.6.1.4.1.2928.2.5.4.5
vasMpuSrcEntryAn entry in the conceptual table represents one multiple pull source object.
VasMpuSrcEntry
.1.3.6.1.4.1.2928.2.5.4.5.1
vasMpuSrcIndexAn index that uniquely identifies the multiple pull source in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.5.1.1
vasMpuSrcRowStatusSee SNMPv2-TC. Use vasMpuSrcAdminStatus to activate and de-activate an Multiple pull source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Multiple pull source. To activate the encoder pipeline, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Multiple pull source is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.5.1.2
vasMpuSrcNameA textual name of the Multiple pull source. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.5.1.3
vasMpuSrcPurposeA text that can describe the purpose of the Multiple pull source. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.5.1.4
vasMpuSrcAdminStatusThe administrative state of the Multiple pull source. The value controls the desired state of the Multiple pull source. up(1). The Multiple pull source shall be enabled. down(2). The Multiple pull source shall be disabled.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.4.5.1.5
vasMpuSrcOperStatusThe operational state of the Multiple Pull source. The value normally follow the state of the administrative state. up(1). The Multiple pull source is up and operational. down(2). The Multiple pull source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasMpuSrcFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.4.5.1.6
vasMpuSrcFailureA string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.5.1.7
vasMpuSrcLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.5.1.8
vasMpuSrcStreamIdAssigns the stream ID to a transport stream. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.5.1.12
vasMpuSrcInputFromA reference to the object that shall supply the video stream to the multiple pull source. This could be e.g. an encoder pipeline on the vasEncPipeTable or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.rw
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.5.1.13
vasPulSnkTableThe conceptual table contains objects that represent the sink (receiver) of a pull transport, i.e. a transport of a stream that is initiated at the sink side, where the stream is pulled from the source to the sink at the sink.
SEQUENCE OF VasPulSnkEntry
.1.3.6.1.4.1.2928.2.5.4.6
vasPulSnkEntryAn entry in the conceptual table represents one pull sink object.
VasPulSnkEntry
.1.3.6.1.4.1.2928.2.5.4.6.1
vasPulSnkIndexAn index that uniquely identifies the pull sink in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.6.1.1
vasPulSnkRowStatusSee SNMPv2-TC. Use vasPulSnkAdminStatus to activate and de-activate a Pull sink. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Pull sink. To activate the Pull sink, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Pull sink is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.6.1.2
vasPulSnkNameA textual name of the Pull sink. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.3
vasPulSnkPurposeA text that can describe the purpose of the Pull sink. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.4
vasPulSnkAdminStatusThe administrative state of the Pull sink. The value controls the desired state of the Pull sink. up(1). The Pull sink shall be enabled. down(2). The Pull sink shall be disabled.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.4.6.1.5
vasPulSnkOperStatusThe operational state of the Pull sink. The value normally follow the state of the administrative state. up(1). The Pull sink is up and operational. down(2). The Pull sink is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPulSnkFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.4.6.1.6
vasPulSnkFailureA string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.7
vasPulSnkLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.6.1.8
vasPulSnkConnectionStatusThe status of the stream transport connection.ro
VasConnectionStatus
.1.3.6.1.4.1.2928.2.5.4.6.1.9
vasPulSnkResetStatisticsResets all statistics counters for the object. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.4.6.1.10
vasPulSnkStatsTrspIndex for an entry in statistics vasTrspStatisticsTable table for this object.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.6.1.11
vasPulSnkStatsTr101Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.6.1.12
vasPulSnkEnableTr101Enables or disables ETSI TR 101 290 statistics collection.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.6.1.13
vasPulSnkRemoteInetTypeFormat of vasPulSrcRemoteInetAddress.ro
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.14
vasPulSnkRemoteInetAddressThe IP address of the remote host from where the transport stream is received. The value is empty and vasPulSnkRemoteInetType is `unknown' when a stream is not received.ro
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.15
vasPulSnkStreamIdSpecifies the stream ID of the stream on the remote host that shall be received. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.16
vasPulSnkPasswordThe password to use for the received transport stream. The password must match the vasPulSrcPassword set on the source at the remote host.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.17
vasPulSnkRemoteHostTypeFormat of vasPulSnkRemoteHostAddress. Supported values are `unknown', `ipv4', and `dns'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.18
vasPulSnkRemoteHostAddressThe IP address or DNS hostname of the remote host from where the transport stream shall be pulled. This address is the first host that will be attempted when a transport stream is to be established.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.19
vasPulSnkRemoteHostType2Format of vasPulSnkRemoteHostAddress2. Supported values are `unknown', `ipv4', and `dns'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.20
vasPulSnkRemoteHostAddress2The second IP address or DNS hostname of the remote host from where the transport stream shall be pulled. When using two addresses, then the transport is setup with two alternative sources. This is a second host that will be attempted if connection to the first host fails when a transport stream is to be established. If a second host shall not be used, then the value shall be empty and the vasPulSnkRemoteHostType shall be `unknown'.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.21
vasPulSnkRemotePortThe UDP port on the remote host that the remote host is listening for connection attempts. See vaStreamPort.rw
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.6.1.22
vasPulSnkRetransmitBufferThe size of the retransmission buffer in milliseconds (ms). The retransmission buffer setting adds bandwidth on the sender side to compensate for packet loss. The setting will affect the allowed maximum bitrate.rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.6.1.23
vasPulSnkFecMaxOverheadThe Forward Error Correction (FEC) overhead in percent (%) of the original stream bit rate. FEC increases the streams tolerance of burst errors and corrects for single errors, as long as they are not clustered, but at the cost of increased latency and is therefore not always desirable.rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.6.1.24
vasPulSnkFecOptimizeWhether to automatically optimize Forward Error Correction (FEC). Optimization will favor the video stream and visually important frames, I and IDR-frames, over others, such as audio. Thereby lowering latency.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.6.1.25
vasPulSnkFecLatencyForward Error Correction (FEC) block size in milliseconds (ms).rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.6.1.26
vasPusSrcTableThe conceptual table contains objects that represent the source (sender) of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source to the sink at the source.
SEQUENCE OF VasPusSrcEntry
.1.3.6.1.4.1.2928.2.5.4.7
vasPusSrcEntryAn entry in the conceptual table represents one push source object.
VasPusSrcEntry
.1.3.6.1.4.1.2928.2.5.4.7.1
vasPusSrcIndexAn index that uniquely identifies the push source in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.7.1.1
vasPusSrcRowStatusSee SNMPv2-TC. Use vasPusSrcAdminStatus to activate and de-activate an Push source. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Push source. To activate the Push source, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Push source is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.7.1.2
vasPusSrcNameA textual name of the Push source. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.3
vasPusSrcPurposeA text that can describe the purpose of the Push source. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.4
vasPusSrcAdminStatusThe administrative state of the Push source. The value controls the desired state of the Push source. up(1). The Push source shall be enabled. down(2). The Push source shall be disabled.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.4.7.1.5
vasPusSrcOperStatusThe operational state of the Push source. The value normally follow the state of the administrative state. up(1). The Push source is up and operational. down(2). The Push source is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPusSrcFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.4.7.1.6
vasPusSrcFailureA string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.7
vasPusSrcLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.7.1.8
vasPusSrcConnectionStatusThe status of the stream transport connection.ro
VasConnectionStatus
.1.3.6.1.4.1.2928.2.5.4.7.1.9
vasPusSrcResetStatisticsResets all statistics counters for the object. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.4.7.1.10
vasPusSrcStatsTrspIndex for an entry in statistics vasTrspStatisticsTable table for this object.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.7.1.11
vasPusSrcRemoteInetTypeFormat of vasPusSrcRemoteInetAddress.ro
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.12
vasPusSrcRemoteInetAddressThe IP address of the remote host to where the transport stream is being sent. The value is empty and vasPusSrcRemoteInetType is `unknown' when a stream is not sent.ro
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.13
vasPusSrcStreamIdAssigns the stream ID to a transport stream. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.14
vasPusSrcInputFromA reference to the object that shall supply the encoded video stream to the push source. This could be e.g. encoder pipeline in the vasEncPipeTable or a UDP sink in the vasUdpSnkTable. The value `.0.0' is used when no input is specified.rw
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.7.1.15
vasPusSrcPasswordA password used for the transport stream. The vasPusSnkPassword on the sink at the remote host must match.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.16
vasPusSrcRemoteHostTypeFormat of vasPusSrcRemoteHostAddress. Supported values are `unknown', `ipv4' and `dns'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.17
vasPusSrcRemoteHostAddressThe IP address or DNS hostname of the remote host to where the transport stream shall be pushed. This address is the first host that will be attempted when a transport stream is to be established.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.18
vasPusSrcRemoteHostType2Format of vasPusSrcRemoteHostAddress2. Supported values are `unknown', `ipv4' and `dns'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.19
vasPusSrcRemoteHostAddress2The second IP address or DNS hostname of the remote host to where the transport stream shall be pushed. This is a second host that will be attempted if connection to the first host fails when a transport stream is to be established. When using two addresses, the transport is setup to two alternative destinations. If a second host shall not be used, then the the value shall be empty and the vasPusSrcRemoteType2 shall be `unknown'.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.20
vasPusSrcRemotePortThe UDP port number on the remote host that the remote host is listening for connection attempts. See vaStreamPort.rw
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.21
vasPusSrcLocalIfTypeDescribes how the vasPusSrcLocalIfAddress shall be interpreted. Supported value is `ipv4'.rw
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.22
vasPusSrcLocalIfAddressThe IP address of a local interface (NIC) that shall be used as output for the video stream. If any interface can be used, set the IPv4 address 0.0.0.0.rw
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.7.1.23
vasPusSrcRetransmitBufferThe size of the retransmission buffer in milliseconds (ms). The retransmission buffer setting adds bandwidth on the sender side to compensate for packet loss. The setting will affect the allowed maximum bitrate.rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.7.1.24
vasPusSrcFecMaxOverheadThe Forward Error Correction (FEC) overhead in percent (%) of the original stream bit rate. FEC increases the streams tolerance of burst errors and corrects for single errors, as long as they are not clustered, but at the cost of increased latency and is therefore not always desirable.rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.7.1.25
vasPusSrcFecOptimizeWhether to automatically optimize Forward Error Correction (FEC). Optimization will favor the video stream and visually important frames, I and IDR-frames, over others, such as audio. Thereby lowering latency.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.7.1.26
vasPusSrcFecLatencyForward Error Correction (FEC) block size in milliseconds (ms).rw
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.7.1.27
vasPusSnkTableThe conceptual table contains objects that represent the sink (receiver) of a push transport, i.e. a transport that is initiated from the source side, and is pushed from the source to the sink at the source.
SEQUENCE OF VasPusSnkEntry
.1.3.6.1.4.1.2928.2.5.4.8
vasPusSnkEntryAn entry in the conceptual table represents one push sink object.
VasPusSnkEntry
.1.3.6.1.4.1.2928.2.5.4.8.1
vasPusSnkIndexAn index that uniquely identifies the push sink in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.8.1.1
vasPusSnkRowStatusSee SNMPv2-TC. Use vasPusSnkAdminStatus to activate and de-activate an Push sink. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Push sink. To activate the Push sink, set the administrative state to up(1) after all columnar objects have been set. destroy(6). The Push sink is deleted. It can be deleted regardless of its operational state.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.8.1.2
vasPusSnkNameA textual name of the Push sink. The name is automatically assigned by the system. The last part of the name is the index in this table.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.8.1.3
vasPusSnkPurposeA text that can describe the purpose of the Push sink. This is for administrative use.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.8.1.4
vasPusSnkAdminStatusThe administrative state of the Push sink. The value controls the desired state of the Push sink. up(1). The Push sink shall be enabled. down(2). The Push sink shall be disabled.rw
Enumeration
.1.3.6.1.4.1.2928.2.5.4.8.1.5
vasPusSnkOperStatusThe operational state of the Push sink. The value normally follow the state of the administrative state. up(1). The Push sink is up and operational. down(2). The Push sink is not operational, either because its administrative state is down, or because of an error. If it is down because of an error, an alarm should be raised and the vasPusSnkFailure should describe the fault.ro
Enumeration
.1.3.6.1.4.1.2928.2.5.4.8.1.6
vasPusSnkFailureA string describing the configuration or error status of the object. The string is the empty string if the configuration is correct and no error is present, otherwise it contains a message describing the error.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.8.1.7
vasPusSnkLastChangedThe value of sysUpTime when status or configuration of the objects was last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.8.1.8
vasPusSnkConnectionStatusThe status of the stream transport connection.ro
VasConnectionStatus
.1.3.6.1.4.1.2928.2.5.4.8.1.9
vasPusSnkResetStatisticsResets all statistics counters for the object. (Not yet implemented).rw
VasResetStatistics
.1.3.6.1.4.1.2928.2.5.4.8.1.10
vasPusSnkStatsTrspIndex for an entry in statistics vasTrspStatisticsTable table for this object.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.8.1.11
vasPusSnkStatsTr101Index for an entry in ETSI TR 101 290 statistics table for this object. (The table is not yet defined).ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.4.8.1.12
vasPusSnkEnableTr101Enables or disables ETSI TR 101 290 statistics collection.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.4.8.1.13
vasPusSnkRemoteInetTypeFormat of vasPusSnkRemoteInetAddress.ro
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.8.1.14
vasPusSnkRemoteInetAddressThe IP address of the remote host from where the transport stream is received. The value is empty and the vasPusSnkRemoteInetType is `unknown' when a stream is not received.ro
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.2928.2.5.4.8.1.15
vasPusSnkStreamIdSpecifies the stream ID of the stream on the remote host that shall be received. The stream ID is a string that identifies the transport stream in all nodes where the stream exists. This must be unique within a node for any given transport stream.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.8.1.16
vasPusSnkPasswordThe password to use for the received transport stream. The password must match the vasPusSrcPassword set on the source at the remote host.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.2928.2.5.4.8.1.17
vasStatisticsGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.2928.2.5.5
vasUdpStatisticsTableThe conceptual table contains perforamance data and counters for UDP video streams.
SEQUENCE OF VasUdpStatisticsEntry
.1.3.6.1.4.1.2928.2.5.5.1
vasUdpStatisticsEntryAn entry in the conceptual table represents statistical data for one UDP object.
VasUdpStatisticsEntry
.1.3.6.1.4.1.2928.2.5.5.1.1
vasUdpStsIndexIndex in the table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.1.1.1
vasUdpStsOwnerReference to the object that allocated and uses this conceptual row.ro
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.5.1.1.2
vasUdpStsBitrateBitrate in bps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.1.1.3
vasTrspStatisticsTableThe conceptual table contains perforamance data and counters for transport streams.
SEQUENCE OF VasTrspStatisticsEntry
.1.3.6.1.4.1.2928.2.5.5.2
vasTrspStatisticsEntryAn entry in the conceptual table represents statistical data for one transport stream.
VasTrspStatisticsEntry
.1.3.6.1.4.1.2928.2.5.5.2.1
vasTrspIndexIndex in table.
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.1
vasTrspOwnerReference to the object that allocated and uses this conceptual row.ro
RowPointer (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.5.2.1.2
vasTrspLastConnectionChangeLast connection status change time.ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.2928.2.5.5.2.1.3
vasTrspConnectsNumber of times that the connection state has changed to `connected'.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.4
vasTrspDisconnectsNumber of times that the connection state has changed to `disconnected'.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.5
vasTrspNetRecvBitrateReceive bitrate in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.6
vasTrspNetRecvBurstLossMaximum number of packets that have been lost in a single burst error.ro
Counter32
.1.3.6.1.4.1.2928.2.5.5.2.1.7
vasTrspNetRecvOctetsThe number of received octets.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.8
vasTrspNetRecvLatencyLatency used for error correction, in milliseconds (ms).ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.9
vasTrspNetRecvDroppedNumber of packets dropped by the network.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.10
vasTrspNetRecvJitterInput jitter in milliseconds (ms).ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.11
vasTrspNetRecvJitterRatioJitter ratio, for rate controlled streams.ro
Integer32
.1.3.6.1.4.1.2928.2.5.5.2.1.12
vasTrspNetRecvOutOfOrderNumber of packets received out of order.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.13
vasTrspNetRecvOverflowsNumber of input jitter buffer overflows.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.14
vasTrspNetRecvPacketsTotal number of received packets.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.15
vasTrspNetRecvPacketRateReceived packets per second.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.16
vasTrspNetRecvPacketLossPacket loss in millipercent (1/100,000)ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.17
vasTrspArqRecvAlmostDroppedNumber of packets that required more than half latency to recover.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.18
vasTrspArqRecvBitrateBitrate of received retransmissions in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.19
vasTrspArqRecvDroppedNumber of packets not recovered by either retransmissions or Forward Error Correction (FEC).ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.20
vasTrspArqRecvDuplicatesNumber of duplicated retransmission packets.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.21
vasTrspArqRecvOverflowsNumber of packets dropped because of retransmission buffer overflow.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.22
vasTrspArqRecvPacketsNumber of packets received by retransmission.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.23
vasTrspArqRecvRecoveredNumber of packets recovered by retransmission.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.24
vasTrspArqRecvRequestsNumber of sent retransmission requests.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.25
vasTrspNetSendBitrateThe send bitrate in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.26
vasTrspNetSendOctetsThe number of sent octets.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.27
vasTrspNetSendLimitThe current sending limit in packets per second.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.28
vasTrspNetSendPacketsTotal number of sent packets.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.29
vasTrspNetSendRttThe return-trip time, RTT, in milliseconds (ms).ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.30
vasTrspNetSendErrorsThe number of packets failed to be sent.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.31
vasTrspArqSendBitrateBitrate of send retransmissions in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.32
vasTrspArqSendIgnoredNumber of ignored too frequent retransmission requests.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.33
vasTrspArqSendMissedNumber of ignored too late retransmission requests.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.34
vasTrspArqSendPacketRateRetransmitted send packets per second.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.35
vasTrspArqSendPacketsNumber of packets sent by retransmission.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.36
vasTrspFecRecvBitrateThe Forward Error Correction (FEC) receive overhead bitrate in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.37
vasTrspFecRecvPacketRateThe Forward Error Correction (FEC) receive packet rate in packets per second.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.38
vasTrspFecRecvPacketsThe number of received Forward Error Correction (FEC) packetsro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.39
vasTrspFecRecvRecoveredThe number of packets recovered by Forward Error Correction (FEC).ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.40
vasTrspFecSendBitrateThe Forward Error Correction (FEC) send bitrate in kbps.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.41
vasTrspFecSendPacketRateThe Forward Error Correction (FEC) receive packet rate in packets per second.ro
Unsigned32
.1.3.6.1.4.1.2928.2.5.5.2.1.42
vasTrspFecSendPacketsThe number of sent Forward Error Correction (FEC) packets.ro
Counter64
.1.3.6.1.4.1.2928.2.5.5.2.1.43
NETI-VAS-MIB - SNMP MIB Reference | MIBs Explorer